TY - CONF A1 - Schmidt, Martin A1 - Erdt, René A1 - Gödde, M. A1 - Salg, St. A1 - Ittemann, L. T1 - Selbstentzündungsverhalten von Feststoffen: Validierung der Extrapolation von Labortests mithilfe halbtechnischer Versuche bis 1 m3 N2 - Vorgestellt wird ein 2018 gestartetes Projekt zur Überprüfung der Extrapolation von im Labormaßstab ermittelten Selbstentzündungstemperaturen auf technisch relevante Volumina. Für die Ermittlung reaktionskinetischer Daten von Feststoffschüttungen stehen eine Reihe von Untersuchungsmethoden zur Verfügung. Dies sind thermische Analysen wie z. B. die differential scanning calorimetry DSC sowie Mikrokalorimetrie zur hochgenauen Messung von Wärmeströmen, bei denen sehr geringe Probenmengen zum Einsatz kommen. In der Regel wird das Selbstentzündungsverhalten jedoch mithilfe von isoperibolen oder adiabaten Warmlagerungsversuchen beurteilt, hier liegen die Probenvolumina üblicherweise im Bereich von ca. 100 cm3 bis zu einigen Litern. Die Extrapolation über mehrere Größenordnungen auf technische Volumina birgt Unsicherheiten, da mit Zunahme des Lagervolumens veränderte Start- und Randbedingungen vorliegen können. Zudem besteht die Möglichkeit, dass bei in technischen Lagern vorherrschenden niedrigen Temperaturen Reaktionen ablaufen, die in Standard- Laborversuchen nicht erfasst werden, aber einen wesentlichen Einfluss auf das Selbstentzündungsverhalten aufweisen können. Hauptziel des Projektes ist es daher, die im Labormaßstab vorhandenen Prüfeinrichtungen durch einen Versuchsstand zur Untersuchung von Probengrößen von bis zu 1000 dm3 zu erweitern, die Eignung (oder Nichteignung) der etablierten Methoden nachzuweisen und im Labormaßstab nicht erfassbare Einflussgrößen zu ermitteln. Zudem sollen anhand der kleinskaligen Tests Entscheidungskriterien abgeleitet werden, ob eine Extrapolation nach den derzeit üblichen Methoden zulässig ist. T2 - 15. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Brunswick, Germany DA - 21.05.2019 KW - Selbstentzündung KW - Formalkinetische Daten KW - Halbtechnische Versuche KW - Thermoanalytische Methoden PY - 2020 SN - 0030-834X VL - 130 IS - 1 SP - 9 EP - 18 AN - OPUS4-51285 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Erdt, René A1 - Gödde, M. A1 - Salg, St. T1 - Validierung der Extrapolation von Labortests mit Hilfe halbtechnischer Versuche bis 1 m3 und thermoanalytischer Methoden N2 - Zur Bestimmung der reaktionskinetischen Daten von Schüttgütern und iur Vorhersage des Selbstentzündungsverhaltens großer.Lager kommen verschiedene Analysemethoden zum Einsatz. Dabei handelt es sich .um thermische Verfahren wie die Differential-Scanning- Kalorimetrie OS(. die simultane Thermoanalyse STA sowie die Mikrokalorimetrie zur hochpräzisen Messung von Wärmeströmen. Für die oben genannten Methoden werden sehr kleine Probenmengen verwendet. In der Regel wird das Selbstentzündungsverhalten jedoch mit Hilfe von isoperibolen oder adiabatischen Warmlagerungsversuchen ermittelt: die Probenvolumina liegen hier meist im Bereich von ca. 100 cm3 bis zu mehreren Litern. Die Extrapolation auf technisch relevante Volumina birgt jedoch erhebliche Unsicherheiten. Diese Unsicherheiten zu identifizieren und zu reduzieren ist das Hauptziel eines 2018 gestarteten Forschungsprojekts. Dies soll in erster Linie durch den Aufbau eines Versuchsstandes zur Untersuchung von Probengrößen von bis zu. 1000 dm 3 geschehen. Sowohl Warmlagerungsversucl1e im Labormaßstab als auch thermoanalytische Verfahren. die mit Hilfe verschiedener Methoden ausgewertet werden. lassen, einzeln betrachtet. häufig nur bedingt zuverlässige Aussagen über das Selbstentzündungsverhalten von großen Schüttgütern zu. Es werden komplette Versuchsreihen mit allen genannten Prüfverfahren vorgestellt und Aussagen zur Anwendbarkeit der Extrapolationsmethoden diskutiert. T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube 2020" CY - Online meeting DA - 04.11.2020 KW - Selbstentzündung KW - Kinetische Daten KW - Halbtechnische Versuche KW - Thermoanalytische Methoden PY - 2020 SN - 978-3-18-092376-5 SP - 17 EP - 36 AN - OPUS4-52443 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, D. A1 - Abbas, Z. A1 - Krause, U. T1 - Ignition temperatures and flame velocities of metallic nanomaterials N2 - The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powders (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2021 KW - Dust explosions KW - Nanomaterial KW - Flame propagation KW - Minimum ignition temperature PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540930 DO - https://doi.org/10.7795/810.20200724 SP - 591 EP - 605 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Krause, U. A1 - Gabel, D. A1 - Abbas, Z. A1 - Dufaud, O. T1 - Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures N2 - Knowledge of explosion limiting concentration of explosible materials is necessary for the design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptions and possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new set-up operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2020 KW - Dust explosions KW - Gas explosions KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540955 DO - https://doi.org/10.7795/810.20200724 SP - 750 EP - 764 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Gödde, M. A1 - Salg, S. A1 - Erdt, René T1 - Self-ignition Behaviour of Bulk Materials: How Reliable is the Extrapolation of Laboratory Tests? N2 - The self-ignition behaviour of bulks is usually determined with the aid of isoperibolic or adiabatic hot storage tests; the sample volumes here are typically in the range of approx. 100 cm³ to several litres. The extrapolation to technically relevant volumes holds, however, considerable uncertainties. To reduce these uncertainties, a test stand was set up that allows to investigation sample sizes of up to 1000 dm³. These allow the study of selfignition behavior closer to the conditions that prevail in practice. The suitability (or unsuitability) of the established methods (including dangerous goods classification tests) were to be demonstrated and influencing variables that cannot be measured on a laboratory scale were to be determined. In addition, various analytical methods were used for the determination of reaction kinetic data of solid bulk materials and to predict the self-ignition behaviour of large storages. These are thermal analyses such as differential scanning calorimetry DSC, simultaneous thermal analysis STA as well as microcalorimetry for highprecision measurement of heat flows. Complete test series using all mentioned test methods will be presented for crosslinked polyvinyl-pyrrolidone (PVP) and conclusions regarding the applicability of the extrapolation methods will be discussed. Hot storage tests up to semi-industrial scale and their combination with various thermoanalytical methods allow a much more precise prediction of the self-ignition behaviour of large bulks. A further promising approach to estimate their heat release rates, and hence, the risk of self-ignition under technical conditions, is the use of microcalorimetric methods. T2 - Loss Prevention 2022 CY - Prag, Czechia DA - 05.06.2022 KW - Self-ignition KW - Kinetic data KW - Semi-technical tests KW - Thermoanalytical methods PY - 2022 SN - 978-88-95608-88-4 DO - https://doi.org/10.3303/CET2290049 SN - 2283-9216 VL - 90 SP - 289 EP - 294 PB - AIDIC AN - OPUS4-55079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Selbstentzündung von Biokohlen – Lager- und Transportsicherheit N2 - Mit der Abkehr von der Nutzung fossiler Rohstoffe rücken regenerative Energieträger immer weiter in den Focus. Neben klassischen Holzkohlen werden verstärkt so genannte Biokohlen produziert. Dieser Begriff findet Verwendung für mit Hilfe verschiedener Verfahren karbonisierte pflanzliche, tierische oder mikrobielle Ausgangsstoffe. Diese Kohlen werden zum Teil über weite Strecken zum Bestimmungsort transportiert (Überseetransporte) oder vor Verwendung für längere Zeit gelagert. Häufig zeigen diese Kohlen ein kritisches Selbstentzündungsverhalten, wobei Einstufungstests (UN N.4 Test) versagen können. Ein negatives Testergebnis des UN N.4 Tests führte dabei in der Vergangenheit zur Nichteinstufung als selbsterhitzungsfähiger Stoff; in der Praxis entzündeten sich aber bereits vergleichsweise kleine Schüttungen (einige m³), z. B. beim Seetransport in Containern. Der Artikel geht auf dieses Problem ein und stellt Prüfverfahren vor. Aus den Ergebnissen durchgeführter Untersuchungen werden Empfehlungen für sicheren Transport und Lagerung abgeleitet. T2 - Magdeburg-Köthener Brandschutz- und Sicherheitstagung CY - Magdeburg, Germany DA - 14.03.2024 KW - Biokohlen KW - Selbstentzündung KW - Gefahrguteinstufung PY - 2024 SN - 978-3-948749-41-5 SP - 68 EP - 77 PB - Otto-von-Guericke-Universität Magdeburg CY - Magdeburg AN - OPUS4-59717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik ED - Krentel, Daniel ED - Grasse, Dennis ED - Gerbeit, Marco ED - Grobert, Steffen ED - Hauer, Thorsten T1 - Experimental Setup for the Reproducible Generation of Pressure Waves in Free Field Conditions N2 - The injuries caused by the primary blast are still poorly understood, especially in the torso region. To generate sufficiently large data sets, shock tubes are often used. However, these have some limitations, such as blockage, use of the exit jet, widening cross-sections, and scaling problems with respect to compressive strength and test objects. Therefore, it is appropriate to conduct experiments under free-field conditions, but tests with real explosives are often associated with long preparation and setup times as well as high safety requirements. Therefore, this paper presents an experimental setup for the reproducible generation of blast waves under free-field conditions. This experimental setup aims to provide a test environment for a sufficiently large specimen to investigate the behaviour of the shock wave within the specimen, especially at the media interfaces. As an example of application, the influence of the primary explosive effect on protective equipment or on tissue simulants for the investigation of blast injuries can be mentioned. An autoclave is used as a shock wave generator. It has a volume of 0.065 m3 and is filled with a stoichiometric acetylene-oxygen gas mixture. The setup and turnaround time is approximately 30 minutes. The following factors have been selected as target variables for the optimization of the shock wave generator: reproducibility of the pressure wave, use-case-relevant positive phase duration and peak overpressure, a pressure curve characteristic corresponding to that of a military explosive under undisturbed free field conditions, and short setup times of the experimental setup. For this purpose, the experimental setup is presented in this paper. Several series of measurements are presented, showing the characteristics of the generated pressure wave. For the generated pressure wave, the classical pressure curve characteristics can be clearly recognized. A peak pressure of 92 kPa is reached at a distance of 1 m from the opening, and the first positive pressure phase lasts 1.17 ms. Furthermore, the pressure wave propagates in a hemispherical shape. The typical characteristics of the blast wave generated by the SWG have been demonstrated using the military explosive PETN. It is shown that the actual load case corresponds to about 70 g of PETN. T2 - 26th International Symposium on Military Aspects of Blast and Shock CY - Wolongong, Australia DA - 03.12.2023 KW - Shock wave generator KW - Blast injury KW - Pressure wave KW - Experimental setup PY - 2023 SP - 1 EP - 13 AN - OPUS4-59357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico A1 - Hahn, Sarah-K. A1 - Krause, Ulrich T1 - BEV Accidents - Consequences in Case of a Battery Thermal Runaway N2 - The number of cars which use a battery for propulsion, like BEV (battery electric vehicle) or PHEV (plug-in hybrid electric vehicle), is increasing. Following, the probability of these car types being involved in car accidents will increase. In a worst-case accident scenario, the installed batteries could go under thermal runaway (TR). A TR could be initiated by various causes, e.g., high temperatures from outside, mechanical damage of the cells/modules/batteries or internal and external short circuits. During such an event, large amounts of heat and toxic and/or flammable gases are released. This poses a great hazard to people and property in the immediate vicinity. The paper describes a large-scale test series on the lithium-ion battery TR consequences of automobile cells and modules up to E = 6.85 kWh. Near field temperatures of ΔT > 800°C in a distance of l = 2 m were measured. During an overcharge test, fragment throwing distances of l > 30 m were detected. Subsequent gas explosions of the released gases were documented. Hydrogen fluoride (HF) was measured in all tests, from cell to module. The highestmeasured concentration was cHF = 76 ppm, which is significantly higher than the 30-min-level for AEGL 2 (acute exposure guideline level 2). Based on the experimentally determined consequences, concrete measures for the accident analysis are subsequently drawn. T2 - 31st Annual Congress of the European Association for Accident Research and Analysis (EVU) CY - Limassol, Cyprus DA - 05.10.2023 KW - Gas release KW - Consequences KW - Lithium-ion battery KW - Electrical Energy Storage KW - BEV PY - 2023 SP - 1 EP - 18 AN - OPUS4-58552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik A1 - Grobert, Steffen A1 - Krentel, Daniel A1 - Hauer, Thorsten T1 - Influence of torso protective equipment on intracorporeal shock wave behavior N2 - In the field of explosive reactions, there is a type of explosive effect that lacks a sufficient database and reproducible experiments regarding biomechanics. It concerns the primary explosive effect. It is defined as pure shock wave of the explosion. The physical behavior of the shock wave when interacting with different types of tissue and, in particular, the subsequent transitions of the shock wave, have barely been investigated. The transition of the shock wave into other materials is the focus of the research Therefore, the aim of the investigations is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times. An autoclave is used to generate the pressure waves. A simplified torso model consisting of ballistic gelatin is used as a simulant. In this paper, the influence of protective equipment on the pressure load in the tissue simulant is investigated. For this purpose, consecutive test setups are used. First, the behavior of ballistic gelatin as a tissue simulant is investigated. Then, the simplified torso model is covered with typical combat clothing consisting of four layers. Afterwards a currently used UHMWPE ballistic protective plate is placed in front of the simplified torso model. Finally, the combat clothing and the protective plate are examined in combination. Three cast-in pressure sensors are used as measuring devices, as well as an acceleration sensor attached to the protective plate. The experiments show that the maximum overpressure in a model rotected by combat clothing and the protective plate can be reduced by 95%. However, the propagation speed of the shock wave within the simplified torso model increases from 1535.5 m/s to 2204.5 m/s. This shows that even protective equipment, which is not primarily intended to protect against blast, offers a significant reduction in the pressure load in the protected area. On the one hand it is caused by the media transition from air to PE and the resulting higher reflection of the acceleration of the transmitted wave within the simulant. On the other hand, it is also reduced due to the damping and dispersion caused by the clothing layers. T2 - 16th International Personal Armour Systems Symposium CY - Dresden, Germany DA - 11.09.2023 KW - Shock wave generator KW - Blast injury KW - Pressure wave KW - Experimental setup PY - 2023 SN - 978-9-0829-2732-0 SP - 178 EP - 187 CY - Brüssel AN - OPUS4-58640 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Sarah-K. A1 - Tschirschwitz, Rico A1 - Amano, Kofi Owusu Ansah A1 - Gimadieva, Elena A1 - Krause, Ulrich T1 - A Study on Thermal Runaway Propagation in Battery Modules Assembled from Pouch Cells N2 - Thermal runaway reactions were studied in arrangements from single battery cells with energy capacities of 2.5 Ah (9.25 Wh) to battery modules up to 6.85 kWh. All cells were pouch cells of the Li-ion NMC type and the modules were composed of such. Abuse was triggered either by overcharging or thermally by attaching a heat source (heating plate or glow plug) to the cells. Experiments with single cells or assemblies of two to four cells were undertaken in closed autoclaves. Samples of the gas released from the cells during the runaway were extracted and analysed using a Fourier-transformed infrared spectrometer (FTIR). In some experiments pressure peaks up to 7 bar (g) were observed which could not be explained by the gas release alone. Obviously, secondary explosions took place. Thermal runaway propagation was studied with and without an insulation layer between the battery cells. Several materials and combinations of them were tested as insulations: hollow glass spheres (Pyrobubbles®), phase change materials (PCM) and intumescent materials. Experiments showed that already layers of 10 to 20 mm of insulation effectively prevented the propagation of a thermal runaway. In addition to the experiments, a mathematical model was developed for studying numerically the heat transfer through arrangements of multiple battery cells and also the effect of insulation layers. This model was implemented into the commercial finite-element software package COMSOL Multiphysics®. The simulations confirmed the experimental findings that already quite thin insulation layers between cells or modules effectively delay or even suppress the propagation of the thermal runaway. T2 - EUSAS conference "Addressing the Fire Risks of Electromobility" CY - Frankfurt am Main, Germany DA - 10.05.2023 KW - Thermal Runaway KW - Consequences KW - Electrical Energy Storage KW - Gas release KW - Lithium-ion battery PY - 2024 UR - https://eusas.eu/publications/eusas-journals VL - 15 SP - 43 EP - 50 PB - EUSAS e.V. (European Society for Automatic Alarm Systems e.V.), Universität Duisburg-Essen, Dept. Nachrichtentechnische Systeme CY - Duisburg AN - OPUS4-61598 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Sarah-K. A1 - Saupe, Alexander A1 - Tschirschwitz, Rico A1 - Bernardy, Christopher A1 - Janßen, Marvin A1 - Amano, Kofi Owusu Ansah A1 - Krause, Ulrich T1 - Sicherheit elektrochemischer Energiespeicher – Ergebnisse aus dem Projekt SEE-2L N2 - Die Transformation der Energienutzung von konventionellen zu erneuerbaren Quellen führt dazu, dass zukünftig mehr Energie effizient zwischengespeichert werden muss. Eine Möglichkeit der elektrochemischen Zwischenspeicherung bieten Lithium-Ionen-Batterien. Hierfür können ausgemusterte Automobilantriebsbatterien verwendet werden. Erfüllen sie die hohen Anforderungen des mobilen Bereichs nicht mehr, haben sie oftmals noch eine ausreichende Kapazität und Leistungsfähigkeit für die stationäre Zwischenspeicherung. Neben der Verwendung der Batterien im größeren Maßstab, z.B. bei Energieversorgern, werden durch den vermehrten Einsatz von Photovoltaik-Anlagen in Ein- und Mehrfamilienhäusern verstärkt Zwischenspeicher für Privathaushalte nachgefragt. Dies birgt auch für Einsatzkräfte neue Herausforderungen in der Gefahrenabwehr. Im vom Bundesministerium für Bildung und Forschung (BMBF) geförderten Verbundprojekt „SEE-2L – Sicherheit elektrochemischer Energiespeicher in Second Life Anwendungen“ wurden Versuche mit Second Life Modulen durchgeführt. Verbundpartner im Projekt waren neben der vfdb die Otto-von-Guericke-Universität Magdeburg und die Bundesanstalt für Materialforschung und -prüfung. Zudem war das Institut der Feuerwehr Nordrhein-Westfalen eingebunden. Die durchgeführten Versuche bilden eine Grundlage für die Einordnung der Batteriespeicher, z.B. aus Sicht des baulichen Brandschutzes, zur Methodik der Brandbekämpfung oder zur Risikobewertung hinsichtlich der Prozess- und Anlagensicherheit. Im Beitrag werden die Versuchsergebnisse vorgestellt und Ansätze für deren Anwendung gezeigt. Um die gewonnenen Erkenntnisse zu vermitteln, wurde im Projekt zudem ein Schulungskonzept für Einsätze mit Lithium-Ionen-Technologien erarbeitet, das im Beitrag präsentiert wird. Es besteht aus theoretischen und praktischen Anteilen, sodass bei den Feuerwehren praxisnah aus- bzw. fortgebildet werden kann. T2 - 70. Jahresfachtagung der vfdb CY - Magdeburg, Deutschland DA - 06.05.2024 KW - Auswirkungsbetrachtungen KW - Elektrische Energiespeicher KW - Lithium-Ionen-Batterie KW - Stationäre Energiespeicher KW - Thermisches Durchgehen PY - 2024 SN - 978-3-9360-5038-7 SP - 645 EP - 657 PB - vfdb, Vereinigung zur Förderung des Deutschen Brandschutzes e.V. CY - Münster AN - OPUS4-60068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - van Wingerden, Kees T1 - Untersuchung der Freisetzung von Flüssigwasserstoff auf und unter Wasser N2 - In einer Reihe von Experimenten wurden die möglichen Folgen der Freisetzung von verflüssigtem Wasserstoff (LH2) auf, bzw. unter Wasser untersucht. Die Experimente zielten darauf ab, eine unbeabsichtigte Freisetzung von LH2 (z.B. durch Schlauchabriss) insbesondere bei der Betankung eines Schiffes zu simulieren. Für verflüssigtes Erdgas (LNG) wurden dabei sog. RPT’s (rapid phase transition) nachgewiesen, bei denen die spontane Verdampfung relevante Druckwellen erzeugt. Es kann nicht ausgeschlossen werden, dass RPTs auch im Falle von LH2 möglich sind. Die Versuche wurden auf dem Testareal Wasserstoffsicherheit auf dem Testgelände Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) in Horstwalde, im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon im Rahmen des SH2IFT-Programms durchgeführt. Die LH2-Freisetzungen erfolgten direkt aus einem LH2-Tanklastwagen über eine lange, flexible, vakuumisolierte Transferleitung. Während die Freisetzung oberhalb und unterhalb der Wasseroberfläche jeweils vertikal orientiert war, wurde bei der Unterwasserfreisetzung zusätzlich eine horizontale Ausströmung, parallel zur Wasseroberfläche realisiert. Zur Bestimmung des Massenstromes, wurde ein Wägesystem unter dem Tankwagen eingesetzt. Spezielle Drucksensoren wurden verwendet, um die durch die Freisetzungsvorgänge erzeugten Stoßwellen sowohl im Wasser als auch in der Luft zu messen. Die Gaskonzentrationen über dem Wasserbecken wurden an verschiedenen Positionen gemessen. Hochgeschwindigkeits-, Infrarot- (IR) und normale Kameras wurden eingesetzt, um die Phänomenologie der Freisetzung aufzuzeichnen und das Verhalten der Gaswolke im Zeitverlauf zu verfolgen. Neben den fest installierten Systemen an Land, kamen auch Unterwasserkameras sowie eine Drohne mit Normal- und IR-Kameras zum Einsatz. Zwei Wetterstationen wurden zur Messung von Windgeschwindigkeit, Windrichtung, Temperatur und Luftfeuchtigkeit während aller durchgeführten Tests eingesetzt. Des Weiteren kamen Bolometer zur Wärmestrahlungsmessung zum Einsatz. Zwar führten die Freisetzung zu einer hochturbulenten LH2/Wasser Mischzone, jedoch zu keinen nennenswerten Überdrücken durch RPT. Im Gegensatz dazu wurde unerwartet, aber reproduzierbar, eine Zündung der Gaswolke in freier Luft in einiger Entfernung von den Instrumenten und dem Ort der Freisetzung beobachtet. Die daraus resultierenden Gaswolkenexplosionen führten zu relevanten Überdrücken und zur Wärmeabstrahlung in die Umgebung. T2 - Magdeburg-Köthener Brandschutz- und Sicherheitstagung 2024 CY - Magdeburg, Germany DA - 14.03.2024 KW - Flüssigwasserstoff KW - LH2 KW - Freisetzung KW - RPT KW - Gaswolkenexplosion PY - 2024 SN - 978-3-948749-42-2 SP - 127 EP - 136 CY - Magedburg AN - OPUS4-59709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Schulze, Marcel A1 - Kant, Hanjo A1 - Orchini, Alessandro ED - Di Benedetto, Almerinda ED - Portarapillo, Maria T1 - Investigation of the thermal radiation from hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests at real-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as leakage diameter (currently up to 30 mm), release pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s). The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration to obtain a (quasi) stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. T2 - 15th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Neaples, Italy DA - 10.06.2024 KW - Hydrogen KW - Release KW - Jet flame KW - Thermal radiation PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-605107 DO - https://doi.org/10.5281/zenodo.12515710 VL - 2024 SP - 1322 EP - 1333 PB - Zenodo CY - Geneva AN - OPUS4-60510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Kant, Hanjo A1 - Schulze, Marcel A1 - Orchini, Alessandro ED - Nabizada, A. ED - Dechany, A. ED - B. Carré, B. ED - Stendardo, E. ED - Lappa, F. ED - Vanlaere, J. ED - Mendoza, M.J. ED - Dejonghe, M. ED - Daese, M. ED - Namazifard, N. ED - Jacops, R. ED - Jottrand, S. ED - Pahlavan, S. T1 - Real scale safety investigations of hydrogen jet flames at high pressure N2 - In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons. T2 - European PhD Hydrogen Conference 2024 (EPHyC2024) CY - Gent, Belgium DA - 20.03.2024 KW - Thermal radiation KW - Release KW - Hydrogen KW - Jet flame PY - 2024 SP - 551 EP - 556 AN - OPUS4-59910 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik T1 - Investigation of Shock Wave Propagation in Soft Tissue Simulants: An Analysis of Organic Gelatin and Synthetic Gel N2 - This study investigates the effects of shock waves on soft tissue simulants, focusing on organic gelatin and a synthetic gel. Although extensive research has focused on the mechanical properties of soft tissue simulants, their behavior under shock wave conditions, such as those caused by blasts, is less understood. As explosives are increasingly used in modern combat scenarios, it is essential to study how shock waves interact with soft tissue. This knowledge is crucial for improving protective equipment and evaluating blast effects on the human body. A two-phase methodology was applied: First, organic gelatin production and synthetic gel composition were analyzed, identifying uncertainties and measuring sound speeds at varying temperatures to align with human tissue properties. Second, simulants were subjected to free-field shock waves, and embedded pressure sensors captured wave propagation, peak overpressures, and propagation velocity. Findings provide comparative insights into shock wave responses of simulants, offering a foundation for future experimental setups. KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Druckwelle PY - 2025 SN - 9781605956978 VL - 34 SP - 63 EP - 79 PB - DEStech Publications Inc. CY - USA AN - OPUS4-63320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik A1 - Grobert, Steffen A1 - Krentel, Daniel T1 - Description of a measurement setup for the combined measurement of LLB exposures in dynamic situations using high-resolution measurement technology N2 - In order to gain an understanding of the Low Level Blast (LLB) exposure of soldiers when using weapon systems, it is necessary to characterize these weapon systems with regard to their overpressure effect [1]. Carrying out static measurements of weapon systems in the rough terrain of firing ranges and training areas poses a challenge for sensitive measurement technology. Furthermore, soldiers are often exposed to LLB in dynamic situations [2]. Therefore, commercially available blast gauges are often used, which, however, are not sufficient for high-resolution measurement of overpressure exposures with academic requirements due to their intended use [3]. Static measurement setups, such as with penile probes, must be used to characterize weapon systems, but they cannot make valid statements about the real load on dynamically behaving soldiers. However, this real load on the soldier is essential in order to be able to adequately assess the potential resulting medical effects. As part of this challenging measurement task, a prototype of a self-sufficient, high-resolution measurement system is presented, which can be used by an operator in dynamic situations without interference. The complete measuring chain was realized as a self-sufficient unit. The system is based on a 20-liter backpack system, which contains the power supply, the measuring amplifier and the measuring card. The measuring computer is attached to the front of the backpack to allow quick access. The measuring system is capable of recording four channels with a sampling rate of up to 2 MHz. Piezoelectric integrated charge pressure sensors are used as a high-resolution pressure sensor (type: PCB138B32). The pressure sensor is placed on a XX- carrier plates with the dimensions XY × YY. The pressure sensors are attached at the typical positions for Blast-Gauges measurements, like on the left shoulder, on the upper chest and on the back of the head. At the same time, commercial blast gauges are placed at the positions of the pressure sensors to qualify the blast gauges (type: B3 Blast Gauges Gen 6). The measuring system is referred to as a “Sensor Carrier Operator (StEk)”. As part of the functional testing of the measurement system, tests are carried out with hand weapons. For this purpose, a soldier is equipped with the StEk and blast gauges. The handguns used are the pistole P8 (caliber 9 mm) and the long rifle G36 (caliber 5.56 mm). The firing position is standing freehand. In addition, the soldier carried out an examination of the carrying comfort of the StEk as part of the training. Furthermore, it was evaluated whether the measuring chain was adequately integrated into the measuring system. The quality of the pressure measurement was also examined, whereby a direct comparison was made with the blast gauges. The measurement system presented here enables the combined (static and dynamic) scientific characterization of weapon systems, particularly with regard to overpressure loading. T2 - Research Specialist Meeting HFM 371 (NATO STO) CY - Toronto, Canada DA - 09.04.2025 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Low Level Blast PY - 2025 SP - 1 EP - 8 AN - OPUS4-63322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Habib, Abdel Karim A1 - van Wingerden, Kees ED - Beyer, Michael ED - Lucassen, Arnas T1 - Large-scale tests to investigate the consequences of exposing cryogenic storage vessels containing liquid hydrogen to a fire load N2 - Large Scale Experiments have been performed to determine whether a storage vessel containing liquid hydrogen (LH2) and caught in a fire engulfing the vessel can result in a BLEVE (Boiling Liquid Expanding Vapour Explosion) and if so its consequences. The tests were performed at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) in Germany at the Hydrogen Test Area (H2TA) within a research cooperation between BAM and Gexcon as part of the SH2IFT program. Three tests were performed using double-walled vacuum insulated vessels of 1 m3 volume. The cylindrical Vessels differed in orientation (horizontal or vertical) and the insulation material used (perlite or multi-layer insulation (MLI)). The degree of filling of the vessels was approximately 35-40 % in each of the tests performed. The fire load was provided by a propane fed burner-system positioned under the storage vessel and designed to give a homogeneous fire load. The conditions in the vessel (temperatures and pressure) as well as external effects (heat radiation, blast waves, flame ball development and fragmentation) were measured. All vessels were equipped with K-type thermocouples at several locations at the inner and outer vessel shell. The pressure inside the inner vessel and in the space between the inner and outer vessels (vacuum pressure) was measured. Bolometers were used to measure the heat radiation generated by both the propane fire and that generated by a possible fireball/BLEVE. To measure blast generated by the vessel burst/BLEVEs blast pencils were positioned at up to three locations. Further several cameras were used to monitor the events: normal cameras, infrared (IR)-cameras, high-speed cameras also on board of an UAV. Two of these vessels, a horizontal and a vertical vessel both insulated with perlite withstood the fire loading for 1 hour 20 minutes and 4 hours respectively without catastrophic failure. A horizontal vessel insulated with MLI failed by bursting after 1 hour and 6 minutes resulting in a fireball, fragments, and blast wave. T2 - 14th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions CY - Braunschweig, Germany DA - 11.07.2022 KW - Prevention KW - Industrial explosions KW - BLEVE KW - LH2 KW - Fire ball KW - Fragments PY - 2022 DO - https://doi.org/10.7795/810.20221124 SP - 168 EP - 181 AN - OPUS4-59440 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Habib, Abdel Karim A1 - van Wingerden, Kees T1 - Unterfeuerung von Flüssigwassersttofftanks - Topologie eines kritischen Behälterversagens N2 - In einer Versuchsreihe im Realmaßstab wurden drei Flüssigwasserstofftanks (LH2) unterfeuert. Hierbei sollte unter anderem geklärt werden, ob es, analog zu druckverflüssigten Gasen, zu einem BLEVE (Boiling Liquid Expanding Vapor Cloud Explosion) kommen kann. Die Experimente wurden auf dem Testareal Wasserstoffsicherheit des Testgeländes Technische Sicherheit der Bundesanstalt für Materialforschung und -prüfung (BAM-TTS) im Rahmen einer Forschungskooperation zwischen der BAM und Gexcon, als Teil des SH2IFT-Programms durchgeführt. Es handelte sich um doppelwandige, vakuumisolierte Tanks von 1 m³ Volumen. Die zylindrischen Tanks unterschieden sich durch ihre Ausrichtung (horizontal oder vertikal) und das verwendete Isoliermaterial (Perlit oder Mehrschichtisolierung (MLI). Der Füllgrad der Tanks betrug bei jedem der durchgeführten Tests etwa 35-40 %. Die Brandlast wurde homogen durch ein propangasbetriebenes Brennersystem erzeugt. Gemessen wurden die Bedingungen im Behälter (Temperaturen und Druck) sowie äußere Randbedingungen und Auswirkungen beim Versagen (Wärmestrahlung, Druckwellen, Flammenballentwicklung und Fragmentierung). Mit Bolometern wurde die Wärmestrahlung gemessen, die sowohl durch das Propanfeuer als auch durch einen möglichen Feuerball/BLEVE erzeugt wurde. Zur Messung der durch das Bersten von Behältern/BLEVEs erzeugten Druckwellen wurden sog. Pencil-Probes verwendet. Des Weiteren wurden mehrere Kameras zur Überwachung der Experimente eingesetzt: Normalbildkameras, Infrarot (IR)-Kameras und Hochgeschwindigkeitskameras, sowohl bodengestützt als auch mittels einer Drohne. Zwei der untersuchten Tanks, ein horizontaler und der vertikale, die beide mit Perlit isoliert waren, hielten der Brandbelastung stand, ohne dass es zu einem Behälterversagen kam. Der mit MLI isolierte horizontale Behälter barst nach 1 Stunde und 6 Minuten und erzeugte dabei einen Feuerball, Trümmerflug und eine Druckwelle. Neben der Beschreibung der Auswirkungen eines kritischen Versagens eines LH2-Tanks sind weitere Ziele der Arbeit die Identifizierung kritischer Behälterzustände sowie die Erstellung eines umfassendes Datensatzes der Trümmer des geborstenen Tanks. Die größten Abstände für kritische Abstände ergaben sich durch Fragmentwurf. Hier sollen 3D-Scans für die Verwendung in CAD und FEM Anwendungen bereitgestellt werden. Umfassende Daten zu den Fragmentwurfweiten, -massen und -positionen wurden bereits publiziert. Damit soll die Voraussetzung geschaffen werden, um vorhandene Wurfweitenmodelle, die bisher nur für einschalige Behälter konzipiert wurden auf ihre Eignung für mehrschalige Behälter zu überprüfen oder mögliche Anpassungen anhand der realen Daten vornehmen zu können. Zudem wurde damit begonnen die nicht geborstenen Tanks zu vermessen und zu zerlegen, um u.a. die Perlit-Schüttung auf Beeinträchtigungen durch den Transport und die Unterfeuerung zu untersuchen. T2 - Magdeburg-Köthener Brandschutz- und Sicherheitstagung 2024 CY - Magdeburg, Germany DA - 14.03.2024 KW - LH2 KW - Flüssigwasserstoff KW - Bleve KW - Tank KW - Bersten KW - Unterfeuerung PY - 2024 SN - 978-3-948749-42-2 SP - 117 EP - 126 CY - Magdeburg AN - OPUS4-59711 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Kant, Hanjo A1 - Schulze, Marcel A1 - Orchini, Alessandro T1 - Sicherheitstechnische Untersuchungen von Wasserstoff Freistrahlflammen bei Hochdruck im Realmaßstab N2 - Wasserstoff als Energieträger gewinnt zunehmend an Bedeutung. Die Untersuchung von Störfallauswirkungen mit Wasserstoff rückt somit stärker in den Fokus. Da Wasserstoff meist unter Druck gelagert und transportiert wird, ist ein zu betrachtendes Szenario die Freisetzung aus einer Leckage mit anschließender Zündung. Die daraus resultierende Freistrahlflamme (Jet Flame) muss hinsichtlich der in die Umgebung emittierten Wärmestrahlung charakterisiert werden. In der Literatur existieren bereits verschiedene Modelle, welche jedoch vermehrt auf Daten aus Kohlenwasserstoffflammen mit geringem Impuls basieren. Zur Überprüfung dieser Modelle wird im Zuge des BAM internen H2 Jet Flame Projektes die sicherheitstechnische Untersuchung von impulsbehafteten Wasserstoff Freistrahlflammen vorgenommen. Hierfür finden Versuche im Realmaßstab auf dem Testgelände Technische Sicherheit der BAM (BAM-TTS) statt. Gegenstand der Untersuchungen ist die Beurteilung der Auswirkungen von realistischen Freisetzungsszenarien hinsichtlich der Flammengeometrie und der freigesetzten Wärmestrahlung. Dabei werden Parameter wie Freisetzungswinkel, Leckagedurchmesser (z.Zt. 1 mm bis 10 mm), Druck (z.Zt. bis max. 250 bar) und Massenstrom (bis max. 0,5 kg/s) variiert. Zusätzlich können auch Einflüsse wie Art der Zündung, Zündort sowie Zündung mit zeitlichem Verzug untersucht werden. Gewonnene Erkenntnisse werden mit den Ergebnissen bereits vorhandener Modelle verglichen und diese im Bedarfsfall weiterentwickelt. Insbesondere wird der Fokus auf die Modellierung der freigesetzten Wärmestrahlung von Wasserstoffflammen gelegt. Herausforderung dabei stellt die IR-Vermessung und Modellierung von Sichtmodellen der Flammen dar. Die Visualisierung der Flammengeometrie wird mit Hilfe mehrerer Infrarot Kamerasystemen (aus mindestens zwei Blickwinkeln) vorgenommen. Bisherige Messungen, die in der Literatur zu finden sind, basieren meist auf instationären Auströmbedingungen. Der hier verwendete Versuchsaufbau ermöglicht ein stationäres Ausströmen für mehrere Minuten und somit eine direkte Vergleichbarkeit mit den existierenden (stationären) Modellen. Weiterhin ist der Versuchsstand umrüstbar für Vergleichsmessungen mit Kohlenwasserstoffen (Methan etc.) sowie Mischungen aus Wasserstoff und Kohlenwasserstoffen. T2 - Magdeburg-Köthener Brandschutz- und Sicherheitstagung 2024 CY - Magdeburg, Germany DA - 14.03.2024 KW - Wärmestrahlung KW - Wassersoff KW - Freistrahlflamme PY - 2024 SN - 978-3-948749-42-2 SP - 137 EP - 146 CY - Magdeburg AN - OPUS4-59912 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico A1 - Krentel, Daniel A1 - Kluge, Martin T1 - Druckgasbehälter im Feuer - Auswirkungen im Versagensfall N2 - Es wurden insgesamt 57 Einzelversuche zum Versagen von Druckgasbehältern durchgeführt. Untersucht wurden dabei 11-kg-Propangasflaschen, PKW-Radmuldentanks für LPG sowie CNG-Tanks vom Typ III (Compositetanks mit Aluminiumliner) und Typ IV (Compositetanks mit Polymerliner). Mit 18 hydraulischen Berstversuchen wurde das Versagensverhalten unter kalten Bedingungen charakterisiert. In 39 Unterfeuerungsversuchen mit den gefüllten LPG- und CNG-Tanks, davon 36 mit Tanks ohne Sicherheitseinrichtung, wurde das Behälterversagen durch Brandbeaufschlagung untersucht. Neben verschiedenen Behältermanteltemperaturen und dem Behälterinnendruck wurde auch die Temperatur des gespeicherten Mediums dokumentiert. Dadurch war es möglich, genau zu dokumen-tieren, unter welchen Bedingungen und bei welchem Zustand der Behälter versagt hat. In einem Großteil der Unterfeuerungsversuche mit Behältern ohne Sicherheitseinrichtungen kam es zur Bildung eines Feuerballs, einer massiven Druck- und Temperaturwirkung auf den Nahbereich sowie einer Vielzahl von Fragmenten im Nah- und Fernbereich. In einer Entfernung von l = 7 m wurden Überdrücke von bis zu p = 0,41 bar gemessen. In 30 Unterfeuerungsversuchen kam es zur Fragmentierung des Behälters. Dabei konnten 159 Fragmente mit Wurfweite und Masse dokumentiert werden. Die dabei maximal festgestellte Wurfweite eines Fragments lag bei l = 311 m. T2 - 15. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Brunswick, Germany DA - 21.05.2019 KW - Behälterversagen KW - Druckgasbehälter KW - Propan KW - LPG KW - CNG PY - 2020 DO - https://doi.org/10.7795/310.20200199 SN - 0030-834X VL - 130 IS - 1 SP - 55 EP - 70 AN - OPUS4-50570 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - van Wingerden, Kees ED - Beyer, Michael ED - Lucassen, Arnas T1 - Experimental investigation into the consequences of release of liquified hydrogen onto and under water N2 - Large-scale experiments have been performed to investigate the possible consequences of realistic amounts of liquified hydrogen (LH2) encountering water. The experiments aimed at simulating an accidental release of LH2 during especially the fuelling of a ship. For liquified natural gas (LNG) it has been demonstrated that when spilled onto water the evaporation rate can be that high that physical explosions occur which are referred as rapid phase transitions (RPTs). It cannot be excluded that RPTs are also possible in the case of LH2. The tests were performed in a 10 m x 10 m x 1.5 m basin filled with water, at the Test Site Technical Safety of the Bundesanstalt für Materialforschung und –prüfung (BAM) in Horstwalde, Germany within a research cooperation between BAM and Gexcon as part of the SH2IFT program. LH2 releases were established releasing directly from a trailer carrying LH2 through a long flexible double vacuum insulated transfer line. The releases occurred from a height of 50 cm above and 30 cm under the water surface both pointing downwards and 30 cm under the water surface pointing along the water surface too. The release rate was determined based on the weight loss rate of the road tanker which was placed onto load cells. Special blast pressure sensors were used to measure the shock waves generated by the release processes both in the water and in the air. At several locations the gas concentration was measured. Heat radiation was measured at 3 distances from the point of release. High speed, Infrared (IR) and normal cameras were used to record events and to follow the gas cloud behaviour in time. This includes cameras mounted on a UAV and underwater cameras. Two weather stations were used to measure wind speed, wind direction, temperature and humidity during all tests performed. All investigated release configurations resulted in a very chaotic LH2-water mixing zone, causing considerable evaporation but only minor over pressures. The main phenomenon observed was an ignition of the released gas cloud, resulting in significant blast wave overpressures and heat radiation to the surroundings. The location of the ignition occurred in free air at some distance from the instrumentation and release location. T2 - 14th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE 2022) CY - Braunschweig, Germany DA - 11.07.2022 KW - LH2 KW - RPT KW - Release KW - Gas cloud explosion KW - Heat radiation PY - 2022 SP - 182 EP - 196 AN - OPUS4-59441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nattuveettil, Keerthana A1 - Liebner, Christian A1 - Tiebe, Carlo T1 - Hydrogen safety- Dealing with Closed Spaces N2 - Hydrogen is under discussion as a potentially clean energy source, but its safe usage and handling in enclosed environments remains a critical challenge due to the properties of hydrogen. This work focuses on detecting and monitoring hydrogen concentration in closed spaces to improve safety by developing a sensor network-based leak detection system to prevent of the accumulation of hazardous mixtures. Furthermore, the study details the implementation of a hydrogen sensor network within a container, analysing sensor placement, data collection, and safety improvements. The findings contribute to better risk assessment and enhanced safety protocols in hydrogen storage and usage facilities. T2 - SMSI 2025 CY - Nuremberg, Germany DA - 06.05.2025 KW - Sensor Network KW - Hydrogen safety KW - QI-Digital PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640630 SN - 978-3-910600-06-5 DO - https://doi.org/10.5162/SMSI2025/C6.2 SP - 167 EP - 168 PB - AMA Verband für Sensorik und Messtechnik e.V. CY - Berlin AN - OPUS4-64063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Leo, Reinhold A1 - Sobol, Oded A1 - Hango, Silas Ithete A1 - Saliwan Neumann, Romeo A1 - Askar, Enis A1 - Boellinghaus, Thomas T1 - Ex-situ investigation of the compatibility of Duplex Stainless Steel for high-pressure hydrogen applications N2 - The key to a successful transition into clean energy carriers such as hydrogen requires the construction of safe transportation pipelines made of alloys which are not susceptible to hydrogen assisted cracking. Duplex Stainless Steels (DSS) are considered as a proper class for components because of their many distinctive qualities. As this consideration depends strongly on the susceptibility level to Hydrogen Assisted Cracking (HAC), the DSS class has been broadly investigated under electrochemical charging conditions. In this work, the interplay between several factors controlling the level of HAC, was examined using light microscopy, high-pressure gaseous hydrogen pre-charging, Electron Backscatter Diffraction (EBSD), tensile testing, fractography and hydrogen concentration measurements using Carrier Gas Hot Extraction (CGHE). The effect of gaseous hydrogen on the mechanical properties with the role of hydrogen induced phase transformation have been investigated both in unused material and in high pressure pipeline section. In contrary to the common electrochemical charging described broadly in the literature, no significant martensitic phase transformation of the austenitic phase was observed. On the other hand, the influence of hydrogen on parameters such as elongation at fracture and reduction of area was noticeable. It is concluded based on the performance of DSS in gaseous hydrogen, that this material has a better potential for utilization in hydrogen applications. As for future experiments, the intention is to analyse the impact of high-pressure gaseous hydrogen on the welded components of this grade, and under mechanical load using the hollow specimen technique. T2 - 5th International Conference on Metals and Hydrogen CY - Ghent, Belgium DA - 14.10.2025 KW - High-Pressure Hydrogen KW - Pipelines KW - Duplex Stainless Steels KW - Hydrogen Assisted Cracking KW - Hollow Specimen Technique PY - 2025 SN - 978-9-08179-424-4 SP - 1 EP - 19 AN - OPUS4-64426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis A1 - Grunewald, Thomas T1 - Experimental Study on the ignition of hydrogen containing atmospheres by mechanical impacts N2 - Mechanical friction, impact or abrasion is one of the ignition sources that must be avoided in hazardous zones with explosive atmospheres. The effectiveness of mechanical impacts as ignition source is dependent from several parameters including the minimum ignition energy of the explosive atmosphere, the properties of the material pairing, the kinetic impact energy or the impact velocity. By now there is no standard procedure to determine the effectiveness of mechanical impacts as ignition source. In this work the effectiveness of mechanical impacts with defined and reproducible kinetic impact energy as ignition source for hydrogen containing atmospheres was studied systematically in dependence from the inhomogeneous material pairing considering materials with practical relevance like stainless steel, low alloy steel, concrete, and non-iron-metals. It was found that ignition can be avoided, if non-iron metals are used in combination with different metallic materials, but in combination with concrete even the impact of non-iron-metals can be an effective ignition source if the kinetic impact energy is not further limited. Moreover, the consequence of hydrogen admixture to natural gas on the effectiveness of mechanical impacts as ignition source was studied. In many cases ignition of atmospheres containing natural gas by mechanical impacts is rather unlikely. No influence could be observed for admixtures up to 25% hydrogen and even more. The results are mainly relevant in the context of repurposing the natural gas grid or adding hydrogen to the natural gas grid. T2 - International Conference on Hydrogen Safety (ICHS) 2023 CY - Quebec City, Canada DA - 19.09.2023 KW - Explosion protection KW - Hydrogen transport in pipelines KW - ATEX KW - Hazardous areas KW - Mechanical sparks KW - Ignition source PY - 2023 SN - 979-12-210-4274-0 SP - 82 EP - 93 AN - OPUS4-58515 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis A1 - Schmidt, Martin A1 - El Harrab, Hayat A1 - Pekalski, Andrzej T1 - Ignition Indices of Hydrogen Mixtures under Electrolysis Process Conditions N2 - The formation of hydrogen-oxygen mixtures for example due to cross-over, malfunction or start-up and shut-down processes is a hazard very specific to given electrolysis processes that must be properly addressed. In this work the explosion limits of hydrogen-oxygen-mixtures at conditions up to 30 bar and 300 °C were determined experimentally. It was found that the existing experimental data can be interpolated with good accuracy using empirical approaches. Moreover, explosion limits at atmospheric conditions were also determined with reduced ignition energy, down to 1 mJ. Although in the literature it can be found that the ignition energy of flammable gases increases strongly when the concentration changes from stoichiometric to near the explosion limits, no significant influence on the mixture concentration was found within tested ignition energy range for H2/O2 mixtures. Finally, hot surface ignition for mixtures with 6 mol% hydrogen in oxygen, thus slightly above the explosion limit, were experimentally studied at different pressures up to 30 bara. Similarly, only slight difference from the ignition temperatures determined for stoichiometric mixtures were found. A 0D adiabatic, constant-volume reactor model was used to calculate the ignition temperatures. The model was tested for its prediction of ignition temperatures of hydrogen mixtures at different pressures. T2 - 11th International Conference on Hydrogen Safety (ICHS) 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Explosion limits KW - Ignition temperature KW - Ignition energy KW - Electrolyzer PY - 2025 SN - 979-12-243-0274-2 VL - 11 SP - 1259 EP - 1271 AN - OPUS4-64525 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - zur Nedden, Philipp Maximilian A1 - von Saldern, Jakob Georg Raimund A1 - Beuth, Jan Paul A1 - Orchini, Alessandro ED - Carcassi, Marco T1 - Thermal radiation of inclined large scale hydrogen jet flames N2 - In order to assess the thermal radiation emanating from hydrogen jet flames, experiments under real scale conditions were carried out at the Test Site Technical Safety of BAM. Herein, the behavior of inclined hydrogen jet flames was investigated. The aim of the work is to determine the Surface Emissive Power and radiant heat fraction of these flames and to provide a reliable dataset for model evaluation purposes. Since the aforementioned values are not directly measurable, the incident heat radiation was measured at defined distances from the flame, as well as the flame's shape and size. The required values were then derived from these measurements. The hydrogen releases ranged from 0.005 kg/s to 0.175 kg/s with a 30 mm orifice. The mass flows were held constant during the releases, nevertheless a transient behavior of the flame could be observed since the experiments were carried out under open field conditions, with unsteady wind fields. In the literature, the flame lengths are often determined using visible light imaging, either by injecting coloring substances in the low light emitting hydrogen jet flame or by carrying out the measurements in darkness. In this work the jet flames were visualized using infrared (IR) and OH* imaging. The recorded flame shapes and resulting flame lengths are compared. Results from this showed that the flame lengths determined with OH* and IR recordings differ greatly. A flame length ratio l_(f OH*)/l_(f IR) in the range of 0.47-0.62 can be found. In addition, the SEP differ also in the range of 10 kW/m²-16 kW/m² (IR) and 40 kW/m²-80 kW/m² (OH*) for hydrogen jet flames due to differences in the determined flame surface. Conclusions regarding the determined x_(RAD )values for IR and OH* result in approximately the same range of 0.031-0.043. T2 - 11th International conference on hydrogen safety 2025 CY - Seoul, Republic of Korea DA - 22.09.2025 KW - IR and OH* measurement KW - Hydrogen release KW - Inclined jet flame KW - Thermal radiation KW - Radiant heat fraction PY - 2025 SN - 979-12-243-0274-2 SP - 837 EP - 849 AN - OPUS4-65362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Krietsch, Arne A1 - Schröder, Volkmar T1 - Comparative study on standardized ignition sources used for explosion testing N2 - For the determination of safety characteristics of gases, vapors and dusts different types of ignition sources are used in international standards and guidelines. Table 1 compares technical relevant ignition sources with their main features. The paper presents test results of a comparative calorimetric and visual study between four different types of ignition sources. The ignition procedures were analyzed visually with a high-speed camera and electric recordings. In addition to that, the influence of the electrode-orientation, -distance as well as ignition energy on the reproducibility of the exploding wire igniter was tested. The exploding wire is already in use for standardized determination of safety characteristics of gases, first tests on the suitability of the exploding wire igniter for dust testing have been carried out by Scheid et al. Using the exploding wire, the ignition energy can be varied from 2 to 10 000 J (2 x 5 000 J) and thus it could be used for gases, vapors, dusts and hybrid mixtures. Moreover it can be used at high initial pressures and it is the only ignition source with an easily measurable ignition energy release. Furthermore, it does not introduce another chemical reaction into the system. Finally, a proposal for a standard ignition source for explosion tests on hybrid mixtures is derived from the test results. T2 - 13th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions CY - Online meeting DA - 27.07.2020 KW - Ignition source KW - Exploding Wire KW - Hybrid mixtures KW - Safety characteristics determination PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-517908 UR - https://oar.ptb.de/files/download/5f3e662f4c93901010006dbf DO - https://doi.org/10.7795/810.20200724 VL - 13 SP - 864 EP - 875 PB - PTB Physikalisch-Technische Bundesanstalt Braunschweig AN - OPUS4-51790 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Krietsch, Arne A1 - Schröder, Volkmar T1 - Entwicklungen zu Bestimmungsverfahren für sicherheitstechnische Kenngrössen hybrider Gemische N2 - Zur Bestimmung sicherheitstechnischer Kenngrößen (STK) von hybriden Gemischen (Gemisch aus mindestens zwei brennbaren Phasen, wie z.B. Staub/Gas- oder Gas/Dampf-Gemisch) existieren bislang keine einheitlichen, genormten Prüfmethoden. Die Normen und Regelwerke zur Bestimmung der STK von einphasigen brennbaren Systemen (Staub, Gas, Dampf) unterscheiden sich teilweise erheblich. Beispielsweise sind in den jeweiligen Normen für Stäube, Gase und Dämpfe unterschiedliche Zündquellen und Zündenergien definiert. Des Weiteren unterscheiden sich die in den Normen definierten Prüfabläufe bei der Gemischherstellung. Bei der Entwicklung einer einheitlichen Norm für hybride Gemische muss der Einfluss dieser beiden Parameter ermittelt werden, um die Vergleichbarkeit mit den STK der einzelnen Komponenten Gas, Staub und Dampf gewährleisten zu können und bisherige Erkenntnisse zu hybriden Gemischen interpretieren und bewerten zu können. T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Online meeting DA - 04.11.2020 KW - Explodierender Draht KW - Sicherheitstechnische Kenngrößen KW - Hybride Gemische PY - 2020 SN - 978-3-18-092376-5 SN - 0083-5560 VL - 2376 SP - 3 EP - 15 PB - VDI Verlag GmbH CY - Düsseldorf AN - OPUS4-51789 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Junias, Josua Kondja A1 - Holtappels, Kai A1 - Liebner, Christian A1 - Thewis, Max A1 - Askar, Enis A1 - Shaanika, Erasmus T1 - Hydrogen Mixtures Flammability Limits Prediction using Machine Learning Models N2 - Flammability characteristics of hydrogen mixtures have been extensively investigated at different initial conditions(temperature and pressure). Based on the available experimental datasets, empirical and semi-empirical models are commonly used to calculate flammability limits in dependance to initial conditions and mixture composition to reduce the experimental effort. However, unevenly distributed empirical data and the complex non-linear relationship characteristics of these data present significant challenges to empirical flammability limits prediction methods under various mixture initial conditions. Moreover, the empirical models and semi-empirical models only cover some influencing parameters, respectively. To address these issues, the present study adapts a machine learning (ML) approach for improving the hydrogen-air/oxygen-inert gas mixture flammability limits prediction at different conditions with a holistic approach. A Multi-Layer Perceptron (MLP) model was trained, validated, and tested using key input features such as flammability state, initial mixture temperature, equivalence ratio, inert gas concentration, adiabatic flame temperature, and Lewis numbers. Data augmentation techniques were conducted on experimental datasets to improve the predictive capability of the model. The models’ performance was compared with empirical flammability limit prediction methods. The goal is to deliver fast, reliable, and more accurate predictions across different scenarios with a single prediction model. Most importantly, the machine learning approach offers a cost-effective and robust alternative to existing empirical flammability limit prediction methods, thus also reducing the experimental effort for explosion limits determination. T2 - 11th International Conference on Hydrogen Safety (ICHS) 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Machine Learning KW - Flammability Limits PY - 2025 SN - 979 -12 -243 -0274 - 2 SP - 1389 EP - 1401 AN - OPUS4-64624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Schulze, Marcel A1 - Kant, Hanjo A1 - Orchini, Alessandro ED - Ruggiero, Eric J. T1 - Experimental investigation of large-scale hydrogen diffusion jet flames N2 - Hydrogen is a promising alternative to natural gas in industrial energy applications which would serve the goal of limiting global warming. However, wide application of hydrogen requires specific safety considerations taking into account that hydrogen is stored and transported under much higher pressure than natural gas. Thus, one scenario to be considered for hazard assessment is a sudden release of hydrogen from a leakage or safety valve and its subsequent ignition. For hydrocarbon flames, various jet flame models are available. However, hydrogen flames significantly differ from hydrocarbon flames in their combustion behavior, so that the applicability of these models to hydrogen has to be investigated. For that purpose, reals scale tests were carried out at the BAM Test Site Technical Safety. In addition, hydrocarbon jet flames (methane) were investigated. In these tests, the flame geometry and the thermal heat radiation were investigated for a release angle of 90°, for different release pressures (up to 220 bar) and mass flows (up to 0.175 kg/s). While existing heat radiation data from the literature are mostly based on unsteady outflow conditions and/or releases in still air, the experiments presented here are focused on ensuring a constant mass flow over the release duration under realistic free field conditions (with wind influence). This allows a better comparability with the stationary jet flame models and assessment of wind influence on model predictions. A number of parameters such as the surface emissive power of the jet flame and the radiant heat fraction were determined. A detailed comparison of the obtained experimental results with literature radiation models was performed. Good agreement between experimental and literature data was found for hydrogen whereas significant differences were identified for methane. Based on the investigations, empirical equations for modelling jet flames could be derived. T2 - American Society of Mechanical Engineers - Turbomachinery Technical Conference & Exposition GT2025 CY - Memphis, TN, USA DA - 16.06.2025 KW - Hydrogen release KW - Jet flame KW - Radiant heat fraction KW - Thermal radiation PY - 2025 SN - 978-0-7918-8877-3 DO - https://doi.org/10.1115/GT2025-FM2 SP - 1 EP - 11 PB - The American Society of Mechanical Engineers CY - Livingston AN - OPUS4-64098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -