TY - JOUR A1 - Epishin, A. I. A1 - Link, T. A1 - Nolze, Gert A1 - Svetlov, I. L. A1 - Bokshtein, B. S. A1 - Rodin, A. O. A1 - Saliwan Neumann, Romeo A1 - Oder, Gabriele T1 - Diffusion processes in multicomponent nickel-base superalloy-nickel system N2 - Optical and scanning electron microscopy, as well as electron microprobe analysis and electron backscatter diffraction, have been used to study diffusion processes that occur in a diffusion pair that consistsof a single-crystal CMSX-10 nickel-base superalloy and polycrystalline nickel, at temperatures of 1050–1250°C. It has been found that, in this system, the distributions of γ-stabilizing elements (Cr, Co, W, and Re) are described by the Boltzmann solution for diffusion between two semiinfinite plates of a binary alloy. The processing of these distributions has shown that the diffusion coefficients of Cr, Co, W, and Re in the multicomponent system are close to those in binary alloys of these elements with Ni. The diffusion redistribution of the elements leads to the dissolution of the γ′ phase in the nickel-base superalloy, growth of nickel grains toward the superalloy constituent of the diffusion pair, and the formation of porosity on both sides of the migrating interface, which is determined from a crystal misorientation of the alloy single crystal and nickel grains. KW - Ni-base superalloy KW - Interface KW - Diffusion KW - Phase transformation KW - Porosity PY - 2014 SN - 0031-918X VL - 115 IS - 1 SP - 21 EP - 29 AN - OPUS4-37980 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolze, Gert A1 - Saliwan Neumann, Romeo A1 - Buchheim, Michaela T1 - Microstructure investigations of iron meteorites by EBSD and EDS analyses N2 - Meteorites are a unique and inspiring material for microstructural studies because if their very specific genesis. Iron meteorites have been formed under unimaginable cooling rates of a few ten Kelvins per million years so that the observable transformation of the formerly huge Fe-Ni single crystals of taenite occurred under nearly-equilibrium conditions. Octahedrites (meteorites having a Ni content between 6...15%) are characterized by ribbons of the low-temperature Fe-Ni phase kamacite separated by rims of residual taenite. This very specific feature is known as Widmanstaetten structure and has been investigated by synchrotron radiation in order to cover a higher volume fraction for a statistically relevant description of orientation relationships. However, plessite – a microstructure mainly consisting of the same phases – reflects the orientation relationship between kamacite and taenite as well. For their characterization, a scanning electron microscope is very suitable in order to investigate crystal orientations or identify phases. Despite the apparently ideal formation circumstances of iron meteorites, Ni concentration profiles prove non-equilibrium conditions. Combined EDS (energy dispersive spectroscopy) and EBSD (electron backscatter diffraction) measurements at a selected plessitic region of the Cape York iron shows that a correlation exists between Ni-concentration and the locally detected orientation relationship. T2 - 15th European Microscopy Congress CY - Manchester, UK DA - 16.09.2012 KW - Phase identification KW - Corrosion KW - Chloride KW - Dermbach PY - 2012 SP - 90 AN - OPUS4-37775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Wencke A1 - Nofz, Marianne A1 - Dörfel, Ilona A1 - Saliwan Neumann, Romeo A1 - Kranzmann, Axel T1 - Aluminiumoxid als Schutzschicht für kommerzielle Kraftwerksstähle (Teil 1) N2 - In Kohlekraftwerken mit Oxyfuel-Technologie erfolgt die Verbrennung unter Zufuhr von reinem Sauerstoff. Damit steht für die Abscheidung und Speicherung von CO2 ein Rauchgas mit hohem CO2-Anteil zur Verfügung (CCS-Technologie). Aufgrund dieses Verbrennungsprozesses ändert sich im Wesentlichen die Rauchgaszusammensetzung hin zu hohem H2O- und SO2 -Anteil. Deshalb wurden in verschiedenen Laboratorien kommerzielle Kraftwerksstähle unter den entsprechenden korrosiven Bedingungen getestet. Im Vergleich zur herkömmlichen Verbrennungsmethode zeigten die ferritisch-martensitischen Stähle schon nach 1000 h Auslagerungszeit unter Oxyfuel-Bedingungen eine durch einen deutlich erhöhten Materialverlust gekennzeichnete Korrosion. Eine Möglichkeit um dennoch die Lebensdauer dieser Stähle zu gewährleisten, besteht im Aufbringen geeigneter Schutzschichten auf die Stahloberfläche. Die vorliegende Arbeit befasst sich mit der Herstellung und Bewertung von Sol-Gel-Aluminiumoxidschichten als Schutz vor Korrosion in Oxyfuel-Rauchgas-Atmosphäre. Diese wurden auf den warmfesten Stahl X20CrMoV12-1 (X20) mittels der Tauchmethode aufgebracht. Anschließend erfolgte eine Auslagerung der beschichteten Proben für 1000 h bei 600 °C in einer H2O-CO2-O2-SO2 -Atmosphäre. Im Vergleich zum unbeschichteten Stahl X20 war der Materialverlust des beschichteten Stahls deutlich geringer. Insbesondere konnte durch die Aluminiumoxidschicht der Transport von CO2 und SO2 zur Stahloberfläche verhindert werden. KW - Stahl KW - Korrosion KW - Aluminiumoxid KW - Sol-Gel PY - 2016 SN - 0016-4232 VL - 107 IS - 9 SP - 1900 EP - 1903 PB - Leuze Verlag CY - Bad Saulgau AN - OPUS4-38148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Wencke A1 - Nofz, Marianne A1 - Dörfel, Ilona A1 - Saliwan Neumann, Romeo A1 - Kranzmann, Axel ED - Leuze-Reichert, Sylvia T1 - Aluminiumoxid als Schutzschicht für kommerzielle Kraftwerksstähle (Teil 2) N2 - In Kohlekraftwerken mit Oxyfuel-Technologie erfolgt die Verbrennung unter Zufuhr von reinem Sauerstoff. Damit steht für die Abscheidung und Speicherung von CO2 ein Rauchgas mit hohem CO2-Anteil zur Verfügung (CCS-Technologie). Aufgrund dieses Verbrennungsprozesses ändert sich im Wesentlichen die Rauchgaszusammensetzung hin zu hohem H2O- und SO2 -Anteil. Deshalb wurden in verschiedenen Laboratorien kommerzielle Kraftwerksstähle unter den entsprechenden korrosiven Bedingungen getestet. Im Vergleich zur herkömmlichen Verbrennungsmethode zeigten die ferritisch-martensitischen Stähle schon nach 1000 h Auslagerungszeit unter Oxyfuel-Bedingungen eine durch einen deutlich erhöhten Materialverlust gekennzeichnete Korrosion. Eine Möglichkeit um dennoch die Lebensdauer dieser Stähle zu gewährleisten, besteht im Aufbringen geeigneter Schutzschichten auf die Stahloberfläche. Die vorliegende Arbeit befasst sich mit der Herstellung und Bewertung von Sol-Gel-Aluminiumoxidschichten als Schutz vor Korrosion in Oxyfuel-Rauchgas-Atmosphäre. Diese wurden auf den warmfesten Stahl X20CrMoV12-1 (X20) mittels der Tauchmethode aufgebracht. Anschließend erfolgte eine Auslagerung der beschichteten Proben für 1000 h bei 600 °C in einer H2O-CO2-O2-SO2 -Atmosphäre. Im Vergleich zum unbeschichteten Stahl X20 war der Materialverlust des beschichteten Stahls deutlich geringer. Insbesondere konnte durch die Aluminiumoxidschicht der Transport von CO2 und SO2 zur Stahloberfläche verhindert werden. KW - Stahl KW - Korrosion KW - Aluminiumoxid KW - Sol-Gel PY - 2016 SN - 0016-4232 VL - 107 IS - 10 SP - 2098 EP - 2102 PB - Leuze-Verlag CY - Bad Saulgau AN - OPUS4-38149 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheibe, Maximilian A1 - Binkowski, Sigrid A1 - Benemann, Sigrid A1 - Saliwan Neumann, Romeo T1 - Comparing different preparation techniques for the characterisation of niobium carbides PY - 2014 UR - http://www.struers.com/article-niobium_carbides_EN UR - http://www.struers.com/article-niobium_carbides_DE IS - 19 SP - 1 EP - 12 AN - OPUS4-32432 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chandra, Kamlesh A1 - Kranzmann, Axel A1 - Saliwan Neumann, Romeo A1 - Rizzo, F. T1 - Comparative study on high temperature oxidation of T92 steel in dry and wet oxyfuel environments N2 - Fireside oxidation of T92 steel was studied after exposure times up to 1000 h in the temperature range of 580–650 °C in simulated dry (CO2–27 % N2–2 % O2–1 % SO2) and wet (CO2–20 % H2O–7 % N2–2 % O2–1 % SO2) oxyfuel environments. Water vapour addition to the oxyfuel gas substantially increased the oxidation rate. The oxide scales developed under wet environment contained more defects, resulting in higher access of oxidants to the substrate material and enhanced oxidation. In addition, the oxide scales had lower chromium enrichment in the inner layer as compared to that in the dry condition. The oxide scales consisted of hematite and magnetite in the outer layer and a mixture of (Fe, Cr)-spinel, sulphides and wustite in the inner layer. The sulphur distribution differed between the oxide scales developed in dry and wet oxyfuel environments. Sulphur was mainly concentrated in the inner layer and at the oxide/alloy interface. In contrast to the wet oxyfuel gas, very high sulphur concentration was measured in the inner oxide scale formed in the dry oxyfuel gas. Additionally, Fe-sulphide was formed at the interface of inner and outer oxide layer in the wet condition. KW - Oxyfuel environment KW - Oxidation KW - High temperature corrosion KW - Water vapour KW - Sulphur PY - 2015 DO - https://doi.org/10.1007/s11085-015-9565-0 SN - 0030-770X SN - 1573-4889 VL - 84 IS - 3-4 SP - 463 EP - 490 PB - Springer CY - New York, NY AN - OPUS4-34585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chandra, Kamlesh A1 - Kranzmann, Axel A1 - Saliwan Neumann, Romeo A1 - Oder, Gabriele A1 - Rizzo, F. T1 - High temperature oxidation behavior of 9-12 % Cr ferritic/martensitic steels in a simulated dry oxyfuel environment N2 - The materials in oxyfuel power plant will be subjected to CO2– and SO2–rich gases on the fireside. The oxidation behaviour of two 9–12 % Cr steels T92 and VM12 was studied under dry oxyfuel environment in the temperature range of 580–650 °C for up to 1,000 h. The oxide structure and morphology were analyzed using various experimental techniques. A complex temperature dependence of oxidation rate is observed for both T92 and VM12 whereby the oxidation rate decreased with increasing temperature. This is attributed to increased Cr-enrichment in the inner scale with increasing temperature. T92 and VM12 alloys are also susceptible to carburization in an oxyfuel environment. KW - Oxyfuel environment KW - Ferritic/martensitic steel KW - Oxidation KW - High temperature corrosion KW - Carburization KW - Steel KW - EPMA KW - SEM PY - 2015 DO - https://doi.org/10.1007/s11085-014-9521-4 SN - 0030-770X SN - 1573-4889 VL - 83 IS - 3-4 SP - 291 EP - 316 PB - Springer CY - New York, NY AN - OPUS4-32737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nofz, Marianne A1 - Zietelmann, Christina A1 - Feigl, Michael A1 - Dörfel, Ilona A1 - Saliwan Neumann, Romeo T1 - Microstructural origin of time-dependent changes in alumina sol-gel-coated Inconel 718 exposed to NaCl solution N2 - Inconel 718 was spin coated twice and fourfold with a sol to obtain 200- and 400-nm-thick transition alumina films on the surface. Bare and sol–gel alumina-coated Inconel 718 samples were exposed to NaCl solution to study their corrosion behavior by means of electrochemical impedance spectroscopy. In combination with scanning electron microscopy, it was shown that bare Inconel 718 is after initial passivation prone to pitting corrosion. For the coated Inconel 718 samples, an improvement in the protective effect of the coatings with time was observed. This observation is in contradiction to the results of other authors who observed degradation of alumina coatings exposed to NaCl solution with time. Transmission electron microscopy revealed a formation of (1) a compacted region at the coating surface as well as (2) a chromium-rich region at the interface between coating and alloy during the contact with a NaCl solution. The last one mainly contributes to the observed chronological sequence of electrochemical characteristics of the samples. KW - Alumina coatings KW - Superalloys KW - Corrosion protection KW - EIS KW - SEM KW - TEM PY - 2015 DO - https://doi.org/10.1007/s10971-015-3668-6 SN - 0928-0707 SN - 1573-4846 VL - 75 IS - 1 SP - 6 EP - 16 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-33338 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sobol, Oded A1 - Nolze, Gert A1 - Saliwan Neumann, Romeo A1 - Eliezer, D. A1 - Böllinghaus, Thomas A1 - Unger, Wolfgang T1 - Novel approach to image hydrogen distribution and related phase transformation in duplex stainless steels at the sub-micron scale N2 - The effect of electrochemical charging of hydrogen on the structure of a lean duplex stainless steel LDX 2101® (EN 1.4162, UNS S32101) was examined by both Time-of-Flight secondary ion mass spectrometry and electron back-scatter diffraction. The goal is to correlate hydrogen concentration and induced structural changes. Chemical and structural characterizations were done for the same region at the sample's surface with sub-micron spatial resolution. Regions of interest were varying in size between 50 × 50 μm and 100 × 100 μm. The results show a phase transformation of austenite to mainly a defect-rich BCC and scarcely a HCP phase. The phase transformation occurred in deuterium rich regions in the austenite. KW - Time-of-flight secondary ion mass spectrometry KW - ToF-SIMS KW - Electron backscatter diffraction KW - EBSD KW - Hydrogen-assisted cracking KW - Data fusion KW - Lean duplex stainless steel PY - 2017 DO - https://doi.org/10.1016/j.ijhydene.2017.08.016 SN - 0360-3199 VL - 42 IS - 39 SP - 25114 EP - 25120 AN - OPUS4-42022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mosquera Feijoo, Maria A1 - Oder, Gabriele A1 - Saliwan Neumann, Romeo A1 - Buchheim, Michaela A1 - Kranzmann, Axel A1 - Olbricht, Jürgen T1 - Impact of Sample Geometry and Surface Finish on VM12‑SHC Ferritic–Martensitic Steel Under Cyclic Steam Atmosphere Operating Conditions N2 - The steam side oxidation of ferritic–martensitic VM12-SHC steel was investigated under thermo-cyclic conditions in water steam at 620/320 °C and 30 bar with a focus on assessing the influence of pre-oxidation time, specimen geometry and surface finish. The specimens were pre-oxidized under isothermal conditions in water steam at 620 °C and 30 bar for 500 h or 1500 h. After pre-oxidation treatment, all specimens were subjected up to 258 thermal cycles. Three different geometries—rectangular coupons, U-shaped ring segments and ring samples—were investigated to evaluate the influence of open/closed shape, and flat/curved surface on corrosion rate. At the same time, two types of surface finish were considered: “as received” and “ground.” The formation of a protective scale by pre-oxidation was investigated. EBSD and ESMA analyses revealed that the Cr-content of the alloy appeared to be insufficient for obtaining a protective oxide scale under studied conditions, at the same time the anayses confirmed that initial oxidation depends on presence of minor alloying elements as Si and Mn, strong oxide formers which can alter the kinetics and morphology of the corrosion reaction. Moreover, rectangular coupons with small wall thickness and flat surface exhibited the highest corrosion rate, while “ground” curved samples showed only local oxidation. This indicates that for same pre-oxidation time, oxidation kinetics is controlled by curvature. KW - Cyclic steam oxidation KW - 12%Cr steel KW - Specimen geometry KW - Surface treatments PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-551808 DO - https://doi.org/10.1007/s11085-022-10114-6 SN - 0030-770X SP - 1 EP - 18 PB - Springer AN - OPUS4-55180 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -