TY - JOUR A1 - Madkour, Sherif Aly Hassan Aly A1 - Yin, Huajie A1 - Füllbrandt, Marieke A1 - Schönhals, Andreas T1 - Calorimetric evidence for a mobile surface layer in ultrathin polymeric films: poly(2-vinyl pyridine) N2 - Specific heat spectroscopy was used to study the dynamic glass transition of ultrathin poly(2-vinyl pyridine) films (thicknesses: 405–10 nm). The amplitude and the phase angle of the differential voltage were obtained as a measure of the complex heat capacity. In a traditional data analysis, the dynamic glass transition temperature Tg is estimated from the phase angle. These data showed no thickness dependency on Tg down to 22 nm (error of the measurement of ±3 K). A derivative-based method was established, evidencing a decrease in Tg with decreasing thickness up to 7 K, which can be explained by a surface layer. For ultrathin films, data showed broadening at the lower temperature side of the spectra, supporting the existence of a surface layer. Finally, temperature dependence of the heat capacity in the glassy and liquid states changes with film thickness, which can be considered as a confinement effect. PY - 2015 DO - https://doi.org/10.1039/c5sm01558h SN - 1744-683X VL - 11 IS - 40 SP - 7942 EP - 7952 PB - RSC Publ. CY - Cambridge AN - OPUS4-34605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie T1 - Thermal and Dynamic Glass Transition of Ultrathin Films of Homopolymers and Their Blends T2 - 27th GCCCD Annual Conference CY - Jena, Germany DA - 2015-08-28 PY - 2015 AN - OPUS4-34589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Yin, Huajie A1 - Madkour, Sherif Aly Hassan Aly A1 - Schönhals, Andreas ED - Kremer, F. T1 - Glass transition of ultra-thin polymer films: A combination of relaxation spectroscopy with surface analytics N2 - The glass transition behavior of ultra-thin supported polymer films is discussed controversially in the literature for around 20 years. Substantial efforts have been archived to understand it. In this contribution, a combination of methods sensitive to bulk properties of a system, like dielectric or specific heat spectroscopy with surface analytics, for instance, atomic force microscopy (AFM), contact angle measurements, and X-ray photoelectron spectroscopy (XPS) were employed to study the glass transition of ultra-thin supported films. All investigations were carried out on identically prepared and treated samples. Different systems with different complexities going from more or less flexible homopolymers over rigid main chain macromolecules to polymer blends have been studied. For the investigated flexible macromolecules, the dynamic glass transition temperature estimated within the frame of the linear response approach is independent of the film thickness down to several nanometers and identical to the bulk value. For polystyrene it was found the thermal glass transition temperatures can depend on the film thickness. This different behavior is not well understood till now and needs further experimental clarification. For the investigated main chain polymers polycarbonate and polysulfone. Dynamic and thermal glass transition temperature estimated from the dielectric measurements increases with decreasing film thickness. This is discussed in the frame of a strong interaction of the polymer segments with the surface of the substrate. In general for homopolymers, the interaction energy of the polymer segments with the substrate surface cannot be considered as the only parameter, which is responsible for the change in the thermal glass transition with the film thickness. For the investigated miscible blend system of polystyrene/poly(vinyl methyl ether) at a composition of 50/50 wt-% a decrease of the dynamic glass transition temperature with decreasing film thickness is found. This is explained by the formation of a poly(vinyl methyl ether)-rich surface layer with a higher molecular mobility. KW - Broadband dielectric spectroscopy KW - Specific heat spectroscopy KW - Photoelectron spectroscopy KW - Contact angle measurements KW - Polystyrene KW - Poly(vinyl methyl ether) KW - Poly(2-vinylpyridine) KW - Polycarbonate KW - Polysulfone KW - Polystyrene/ Poly(vinyl methyl ether) blend PY - 2014 SN - 978-3-319-06099-6 SN - 978-3-319-06100-9 DO - https://doi.org/10.1007/978-3-319-06100-9_2 SN - 2190-930X SN - 2190-9318 SP - 17 EP - 59 PB - Springer AN - OPUS4-31078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Madkour, Sherif Aly Hassan Aly A1 - Schönhals, Andreas T1 - Unambiguous evidence for a highly mobile surface layer in ultrathin polymer films by specific heat spectroscopy on blends N2 - Despite the decade long controversial discussion on the effect of nanometer confinement on the glass transition temperature (Tg) of ultrathin polymer films, there is still no consistent picture. Here, the dynamic calorimetric glass transition of ultrathin films of a blend, which is miscible in the bulk, is directly investigated by specific heat spectroscopy. By a self-assembling process, a nanometer thick surface layer with a higher molecular mobility is formed at the polymer/air interface. By measuring the dynamic calorimetric Tg in dependence on the film thickness, it was shown that the Tg of the whole film was strongly influenced by that nanometer thick surface layer, with a lower Tg. Since the observed thickness dependence of the dynamic Tg is similar to the thickness dependence of the Tg for thin films of homopolymers, it is concluded that also for homopolymer a highly mobile surface layer is relevant for the widely observed Tg depression. PY - 2015 DO - https://doi.org/10.1021/acs.macromol.5b01259 SN - 0024-9297 SN - 1520-5835 VL - 48 IS - 14 SP - 4936 EP - 4941 PB - American Chemical Society CY - Washington, DC AN - OPUS4-33841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Schubert, Martina A1 - Schartel, Bernhard A1 - Lang, M. A1 - Yin, Huajie A1 - Dittrich, Bettina A1 - Heidemeyer, P. A1 - Bastian, Martin T1 - Wirkungsweise von halogenfreien Flammschutzmitteln in WPC N2 - Das Ziel des Forschungsvorhabens war die Untersuchung der Wirkungsweise von halogenfreien Flammschutzmitteln in WPC. Eine große Anzahl verschiedener Flammschutzmittel wurde hinsichtlich ihrer Wirkmechanismen umfassend untersucht, um ein Verständnis für die ablaufenden Prozesse zu entwickeln. Hierbei wurden verschiedene Brandtests eingesetzt, um die Materialien bezüglich verschiedener Applikationen (E&E, Transportwesen, Bauwesen) zu beleuchten. Die verschiedenen Untersuchungen liefern aber auch ein umfassendes Bild vom Brandverhalten in den verschiedenen Eigenschaften, wie Entflammbarkeit und Brandausbreitung. Die prinzipiellen Ansätze wurden anhand von verschiedenen Flammschutzmitteln beleuchtet, ihre Pyrolyse und ihre Performance in verschiedenen Brandtests gegenübergestellt. Bei der angestrebten geringen Zusatzmenge ist durch den Zusatz eines einzigen Flammschutzmittels keine zufriedenstellende Reduktion der Brandeigenschaften zu erwarten. Multikomponentensysteme zur Steigerung der Effizienz sind angezeigt. Einige prinzipielle Kombinationsmöglichkeiten wurden für alle Hauptflammschutzmittel durchgespielt. Die teilweise deutlichen Verbesserungen zeigen Wege zur erfolgreichen Produktentwicklung auf. So konnten bei den Spritzgießcompounds Eigenschaften erzielt werden, die eine UL 94 V0 Klassifizierung ermöglichen. Ein Einsatz der im Forschungsvorhaben hergestellten Compounds als Baustoff ist aufgrund des Brandverhaltens in den baustoffspezifischen Prüfungen nicht möglich. Hier sind weitere Flammschutz-Konzepte zu erproben. Gleitmittel nehmen bei den untersuchten Extrusionscompounds keinen Einfluss auf das Brandverhalten. Haftvermittler nehmen ebenfalls keinen signifikanten Einfluss auf das untersuchte Brandverhalten, können aber zu einer veränderten Verteilung der Füllstoffe und damit zur Ausbildung einer effektiveren Schutzschicht führen. Feinere Holzpartikel schneiden bei den Brandprüfungen besser ab als grobe Holzpartikel. Bei Einsatz von grobem Holz wird eine schlechtere Rückstandsstruktur ausgebildet, was das Brandverhalten negativ beeinflusst. Der Einsatz von vorbehandeltem Holz brachte nicht die erwartete Verbesserung. Die neu konzipierte Aufbereitungsanlage auf Basis des Planetwalzenextruders konnte erfolgreich in Betrieb genommen werden. Vergleichende Versuche mit dem Doppelschneckenextruder zeigten, dass der PWE-Aufbau eine gute Alternative zur etablierten DSE-Aufbereitung darstellt. Zusätzlich wurden an Compounds vielversprechender Flammschutzansätze weitere Materialprüfungen (Biegeversuch, Schlagversuch, Wasseraufnahme) durchgeführt, um den Einfluss der FSM auf die spezifischen Eigenschaften der WPC zu beleuchten. N2 - The objective of the research project was to investigate the effect of halogen-free flame retardants in WPC. A large number of different flame retardants was thoroughly examined regarding their effect mechanisms to develop an understanding for the processes taking place. Different fire tests were used to examine the materials with respect to the different applications (E&E, transportation, construction). Additionally, the different investigations provide a comprehensive picture of the fire behavior regarding the different properties, such as flammability and fire spread. The fundamental approaches were examined by means of different flame retardants and their pyrolysis and performance were compared in different fire tests. A satisfactory reduction of the fire properties by adding only one flame retardant cannot be expected with the intended low added amount. Multi-component systems to increase the efficiency are indicated. Some basic combination options were tried out for all main flame retardants. The partially considerable improvements illustrate ways for successful product development. This way, properties could be achieved in injection molding compounds, which allow for a UL 94 V0 classification. It is not possible to use the compounds introduced in the research project as building material due to the fire behavior in the building material specific tests. Further flame protection concepts need to be tested in this area. Slip agents do not have an influence on the fire behavior of the examined extrusion compounds. Adhesion promoters also do not have a significant influence on the examined fire behavior but can lead to a change in the distribution of the fillers and thus to the formation of a more effective protective layer. Finer wood particles performed better in the fire tests than coarse wood particles. When using coarse wood, an inferior residual structure is formed, which has an adverse effect on the fire behavior. The use of pretreated wood fibers did not bring the expected improvement. The newly conceived processing technique based on a planetary roller extruder (PRE) was successfully put into operation. Comparative tests with twin-screw extruders (TSE) showed that the PRE configuration is a good alternative to the established TSE processing. Additionally, further material testing (bending test, impact test, water absorption) was performed on promising flame retarded compounds to examine the influence of the fire retardants on the specific properties of the WPC. KW - Wood plastic composite KW - Halogen free KW - Flame retardancy PY - 2016 SN - 978-3-8440-4645-8 SN - 2364-754X SP - 1 EP - 88 PB - Shaker Verlag CY - Aachen AN - OPUS4-37482 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Napolitano, S. A1 - Schönhals, Andreas T1 - Molecular mobility and glass transition of thin films of poly(bisphenol A carbonate) N2 - Glass transition behavior of thin poly(bisphenol A carbonate) (PBAC) films capped between two aluminum (Al) layers is investigated by means of dielectric expansion dilatometry and dielectric relaxation spectroscopy accompanied by contact angle measurements. The thermal glass transition temperature is more or less independent of the film thickness down to 20 nm. For thickness below 20 nm, an increase of Tg is observed. Meanwhile, an increase of the relaxation time at a fixed temperature is observed for the film with the thickness of 19 nm on the basis of a careful analysis of the temperature dependence of the relaxation rates. A more detailed analysis of the relaxation map reveals that the Vogel temperature increases and the fragility decreases systematically with decreasing film thickness. These properties are discussed in terms of the formation of a boundary layer with PBAC segments adsorbed onto the Al electrode due to the strong interaction between the Al and PBAC layers (2.51 mJ/m²), which results in a reduced molecular mobility with regard to bulk PBAC behavior. As the dielectric strength is proportional to the number of segments fluctuating on the time and length scale of the dynamic glass transition, it is used as a unique probe of the deviations from bulk behavior. The temperature dependence of the penetration depth of the interfacial interactions on the structural relaxation is further quantitatively determined. The dynamic length scale of the perturbations into the chain conformations responsible for the deviation from bulk behavior is estimated to be smaller than 9 nm. PY - 2012 DO - https://doi.org/10.1021/ma202127p SN - 0024-9297 SN - 1520-5835 VL - 45 IS - 3 SP - 1652 EP - 1662 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Calorimetric glass transition of ultrathin poly(bisphenol A carbonate) films N2 - Specific heat spectroscopy in the frequency range from 1 Hz to 10³ Hz with a sensitivity of pJ K-1 was employed to study the glass transition behavior of ultrathin poly(bisphenol A carbonate) (PBAC) films with thicknesses ranging from 192 nm down to 10 nm. The amplitude and the phase angle of the complex differential voltage as a measure of the complex heat capacity were obtained as a function of temperature at a given frequency simultaneously. Both spectra are used to determine the dynamic glass transition temperature as a function of both the frequency and the film thickness. As the main result no thickness dependence of the dynamic glass transition temperature was observed down to a film thickness of 10 nm within the experimental uncertainty of ±3 K. The obtained data were compared with literature results in detail. PY - 2012 DO - https://doi.org/10.1039/c2sm26174j SN - 1744-683X VL - 8 IS - 35 SP - 9132 EP - 9139 PB - RSC Publ. CY - Cambridge AN - OPUS4-26379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Boucher, V.M. A1 - Cangialosi, D. A1 - Yin, Huajie A1 - Schönhals, Andreas A1 - Alegría, A. A1 - Colmenero, J. T1 - Tg depression and invariant segmental dynamics in polystyrene thin films N2 - We investigate the segmental dynamics and glass transition temperature (Tg) of polystyrene (PS) thin films. The former is investigated by alternating current (AC) calorimetry and dielectric spectroscopy (BDS). The Tg, underlying the equilibrium to out-of-equilibrium crossover from the supercooled liquid to the glass, is obtained by differential scanning calorimetry (DSC) and capacitive dilatometry (CD). We show that the intrinsic molecular dynamics of PS are independent of the film thickness both for the freestanding and supported films, whereas Tg decreases with film thickness from several microns down to 15 nm. This result is found for complementary methods and in a simultaneous measurement in BDS and CD. This questions the widespread notion that segmental mobility and the equilibrium to out-of-equilibrium transition are, under any experimental conditions, fully interrelated. For thin films, it appears that the molecular mobility and Tg are affected differently by geometrical factors. PY - 2012 DO - https://doi.org/10.1039/c2sm25419k SN - 1744-683X VL - 8 IS - 19 SP - 5119 EP - 5122 PB - RSC Publ. CY - Cambridge AN - OPUS4-25805 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Glass transition and segmental dynamics of ultrathin poly(bisphenol A carbonate) films N2 - Broadband dielectric spectroscopy (BDS), capacitive scanning dilatometry (CSD) and differential ac-chip calorimetry (DACC) were used to examine the glass transition and segmental dynamics of ultrathin poly(bisphenol A carbonate) (PBAC) films. An increase of Vogel temperature (T0) as well as glass transition temperature (Tg) with decreasing film thickness was observed when the thickness is less than 20 nm. Moreover, the segmental relaxation time at a fixed temperature was found to increase for the aluminium (Al) capped PBAC films (<20 nm) in the BDS measurements, whereas in the DACC measurements no thickness dependency of the segmental dynamics was detected within the experimental error limit for the supported PBAC films (10-55 nm). These properties are discussed in terms of the thin film geometry and the relevant interfacial interaction between the polymer and the substrate. T2 - 6th International conference on times of polymers (TOP) and composites CY - Ischia, Italy DA - 10.06.2012 KW - Ultrathin film KW - Poly(bisphenol A carbonate) KW - Glass transition KW - Aluminium KW - Dielectric thin films KW - Differential scanning calorimetry KW - Permittivity KW - Polymer films PY - 2012 SN - 978-0-7354-1061-9 DO - https://doi.org/10.1063/1.4738399 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings IS - 1459 SP - 64 EP - 67 AN - OPUS4-26349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie T1 - Comparing Different Routes to Halogen-free Flame Retardant Wood-Plastic Composites T2 - Eurofillers Polymer Blends 2015 CY - Montpellier, France DA - 2015-04-26 PY - 2015 AN - OPUS4-33186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Yin, Huajie A1 - Schönhals, Andreas ED - Utracki, L.A. ED - Wilkie, C. A. T1 - Broadband dielectric spectroscopy on polymer blends N2 - In this chapter broadband dielectric spectroscopy (BDS) is employed to polymeric blend systems. In its modern form BDS can cover an extraordinary broad frequency range from 10-4 to 1012 Hz. Therefore, molecular and collective dipolar fluctuations, charge transport, and polarization effects at inner phase boundaries can be investigated in detail including its temperature dependence. In the first part of the chapter, the theoretical basics of dielectric spectroscopy are briefly introduced covering both static and dynamic aspects. This section is followed by short description of the various experimental techniques to cover this broad frequency range. To provide the knowledge to understand the dielectric behavior of polymeric blend systems, the dielectric features of amorphous homopolymers are discussed in some detail. This concerns an introduction of the most important relaxation processes observed for these polymers (localized fluctuations, segmental dynamics related to the dynamic glass transition, chain relaxation), a brief introduction to the conductivity of disordered systems as well as polarization effects at phase boundaries. Theoretical models for each process are shortly discussed. In the last paragraph the dielectric behavior of polymer blends is reviewed where special attention is paid to binary systems for the sake of simplicity. In detail the dielectric behavior of binary miscible blends is described. The two most important experimental facts like the broadening of the dielectric relaxation spectra and the dynamic heterogeneity of the segmental dynamics are addressed in depth. Appropriate theoretical approaches like the temperature-driven concentration fluctuation model and the self-concentration idea are introduced. PY - 2014 SN - 978-94-007-6063-9 SN - 978-94-007-6064-6 SN - 978-94-007-6065-3 DO - https://doi.org/10.1007/978-94-007-6064-6_14 SP - Chapter 12, 1299 EP - 1356 PB - Springer Science + Business Media AN - OPUS4-32087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie T1 - Investigation of Wood-Plastic Composites (WPCs) Using Different Flame Retardants T2 - Kolloquiumsvortrag BEIJING INSTITUTE OF TECHNOLOGY CY - Beijing, China DA - 2014-11-24 PY - 2014 AN - OPUS4-32357 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie T1 - Wood Flour/Polypropylene Composites Using Different Flame Retardants T2 - Kolloquiumsvortrag, Insitute of Chemistry, the Chinese Academy of Sciences CY - Beijing, China DA - 2014-11-26 PY - 2014 AN - OPUS4-32358 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie T1 - Improvement on the Flame Retardancy of Wood-Plastic Composites (WPCs) Using Different Flame Retardants T2 - Kolloquiumsvortrag, Sichuan University CY - Chendu, China DA - 2014-11-27 PY - 2014 AN - OPUS4-32359 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Mix, Renate A1 - Yin, Huajie A1 - Friedrich, Jörg Florian ED - Gutowski, W. ED - Dodiuk, H. T1 - Aerosol-based DBD - A simple way to provide polymers with functional groups for adhesion promotion N2 - Polypropylene (PP) foils were exposed to the plasma of an atmospheric dielectric barrier discharge (DBD) in presence of different aerosols. Pure liquids such as water, ethanol, and 1/1 mixtures ethanol/water (v/v) or aqueous Solutions of acetic acid, poly(acrylic acid), poly(vinyl alcohol), and ethylene glycolpoly(vinyl alcohol) copolymer were introduced into the DBD. Surface composition, the number of functional groups per 100 C atoms, and water contact angles were correlated with the energy density of DBD plasma exposure. The wettability of the treated surfaces was investigated for different storage times. Peel strength of the thermally deposited aluminum layer to modified polymer surfaces revealed that the aerosol introduction strongly improves the adhesion between aluminum and polypropylene. KW - Aerosol-assisted DBD KW - Functional groups KW - Surface modification PY - 2013 SN - 978-90-04-20173-6 SN - 978-90-04-20174-3 SP - Chapter 8, 155 EP - 170 PB - CRC Press AN - OPUS4-30035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Deng, C. A1 - Yin, Huajie A1 - Li, R.-M. A1 - Huang, S.-C. A1 - Schartel, Bernhard A1 - Wang, Y.-Z. T1 - Modes of action of a mono-component intumescent flame retardant MAPP in polyethylene-octene elastomer N2 - A mono-component intumescent flame retardant named ethylenediamine-modified ammonium polyphosphate (MAPP) is used in polyethylene-octene elastomer (POE). Insight into the flame-retardant mechanisms of the MAPP is provided from a new perspective. The fire performance of POE/MAPP composites is investigated by oxygen index (OI) and vertical burning (UL-94) tests. POE Composite containing 35 wt% MAPP achieves a V-0 rating, and its OI is 29.3 vol%. The thermogravimetric Analysis (TGA) and Fourier transform infrared spectra (FTIR) confirm that the incorporation of ethylenediamine changes the thermal decomposition of APP, mainly resulting in the formation of char layer with a thermally stable structure. Cone calorimeter analysis revealed the flame-retardant modes of action of MAPP in POE under forced-flaming conditions. Quantitative analysis illustrates that both the residue due to charring and the fuel dilution/flame Inhibition resulting from the release of incombustible products/ phosphorus species decrease the total heat release (fire load) by 20e28%. The residue increases linearly with increasing MAPP content, whereas the reduction in effective heat of combustion levels off. Moreover, the flame-retardant effect resulting from the protective properties of the char is discovered to be the dominant mode of action (up to 85% reduction) with respect to the peak heat release rate, leading to the excellent flame retardancy of POE/MAPP. KW - Ammonium polyphosphate KW - Flame retardant KW - Carbonization KW - Elastomer PY - 2017 DO - https://doi.org/10.1016/j.polymdegradstab.2017.03.006 SN - 0141-3910 SN - 1873-2321 VL - 138 SP - 142 EP - 150 PB - Elsevier AN - OPUS4-39901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Dittrich, Bettina A1 - Farooq, Muhammad A1 - Kerling, S. A1 - Wartig, K.-A. A1 - Hofmann, D. A1 - Huth, Christian A1 - Okolieocha, C. A1 - Altstädt, V. A1 - Schönhals, Andreas A1 - Schartel, Bernhard T1 - Carbon-based nanofillers/poly(butylene terephthalate): thermal, dielectric, electrical and rheological properties N2 - The influence of distinct carbon based nanofillers: expanded graphite (EG), conducting carbon black (CB), thermally reduced graphene oxide (TRGO) and multi-walled carbon nanotubes (CNT) on the thermal, dielectric, electrical and rheological properties of polybutylene terephthalate (PBT) was examined. The glass transition temperature (Tg) of PBT nanocomposites is independent of the filler type and content. The carbon particles act as nucleation agents and significantly affect the melting temperature (Tm), the crystallization temperature (Tc) and the degree of crystallinity of PBT composites. PBT composites with EG show insulating behaviour over the tested concentration range of 0.5 to 2 wt.-% and hardly changed rheological behaviour. CB, CNT and TRGO induce electrical conductivity to their particular PBT composites by forming a conducting particle network within the polymer matrix. CNT reached the percolation threshold at the lowest concentration (<0.5 wt.-%), followed by TRGO (<1 wt.-%) and CB (<2 wt.-%). With the formation of a particle network, the flow behaviour of composites with CB, CNT and TRGO is affected, i.e., a flow limit occurs and the melt viscosity increases. The degree of influence of the carbon nanofillers on the rheological properties of PBT composites follows the same order as for electrical conductivity. Electrical and rheological results suggest an influence attributed to the particle dispersion, which is proposed to follow the order of EG<< CB