TY - CONF A1 - Stuckert, J. A1 - Birchley, J. A1 - Große, M. A1 - Fernandez-Moguel, L. A1 - Onel, Yener A1 - Rössger, C. A1 - Steinbrück, M. T1 - The Quench-Debris test - Experimental results and modeling N2 - In the framework of the SARNET-2 WP5.1 the QUENCH-DEBRIS test was conducted as the 17th severe accident test using the QUENCH facility at KIT to investigate the formation and coolability of a prototypic debris bed. The test scenario was defined by pre-test calculations using the MELCOR code. This code was used also for post-test analysis. The test bundle with length of about 2 m contains the hafnium shroud tube and 12 heated peripheral rods with claddings made of hafnium. Hafnium was chosen because of its much higher melting temperature and the about one order of magnitude lower oxidation rate compared to zirconium. The claddings of the inner nine rods were made from Zry-4. They were filled with pre-fragmented zirconia pellets. The test started with an oxidation phase of 20 h at peek cladding temperature about 1800 K to reach complete oxidation of the Zry-4 claddings over a height of 500 mm. The temperatures expected from the pre-test simulation fitted well the experimentally observed evolution of the bundle conditions. The possibly surviving inner Zry-4 claddings were destroyed by the application of an axial mechanical force resulting in material relocation and formation of a heterogeneous debris bed consisting of segmented pellets and larger cladding tube fragments at the grid spacer 2 (350 mm elevation) and in a smaller amount at grid spacer 3 (1050 mm elevation). The so destroyed bundle was quenched with 10 g/s water. The evaporation rate generally showed an increasing trend during the reflood, except at the time of water penetration through the debris bed at spacer 2 when stagnation was observed. All peripheral hafnium claddings survived the whole test. During the oxidation phase about 100 g hydrogen was released. The time dependence of the hydrogen release predicted in the pre-test calculations fits well the measured one. The post-test examinations comprise videoscope inspections, high energy X-ray-tomography and metallographic investigations of the debris bed. T2 - ERMSAR-2013 - 6th European review meeeting on severe accident research CY - Avignon, France DA - 02.10.2013 KW - Hochenergie-Computertomographie KW - Nukleare Sicherheitsforschung PY - 2013 SP - 1 EP - 13 (Paper 2.6) AN - OPUS4-29467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Onel, Yener A1 - Lange, Axel A1 - Staude, Andreas A1 - Ehrig, Karsten A1 - Kupsch, Andreas A1 - Hentschel, Manfred P. A1 - Wolk, Thomas A1 - Müller, Bernd R. A1 - Bruno, Giovanni T1 - Evaluating porosity in cordierite Diesel particulate filter materials, Part 2 statistical analysis of computed tomography data N2 - Complementary to Part 1 of this work, the bi-continuous microstructure of porous synthetic cordierite ceramics for filtration applications was investigated using 3D x-ray computed tomography at different resolutions. Applying both Fast Fourier Transform and a newly developed image analysis algorithm, we quantitatively evaluated porosity and pore orientation. The statistical approach allows extraction of spatially resolved or average values. Porosity values based on x-ray absorption agree with mercury intrusion measurements, while pore orientation factors agree with x-ray refraction data (Part 1 of this work), and with published crystallographic texture data. KW - Pore orientation KW - Porous ceramics KW - Computed tomography KW - 3D microstructure PY - 2013 DO - https://doi.org/10.4416/JCST2013-00022 SN - 2190-9385 VL - 05 IS - 01 SP - 13 EP - 22 PB - Göller CY - Baden-Baden AN - OPUS4-30379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Illerhaus, Bernhard A1 - Badde, Aurelia A1 - Michaelis, Matthias A1 - Berger, U. A1 - Onel, Yener A1 - Meinel, Dietmar A1 - Goebbels, Jürgen T1 - Einsatz von mobilen Röntgenuntersuchungsmethoden im Museum - Zwei Fallbeispiele N2 - Zwei Bildhauermodelle aus dem Georg-Kolbe-Museum Berlin standen zur Restaurierung an. Das kleinere, 'Lucino' (1920), 41cm, wurde hochauflösend mit CT gemessen, da mittels CT sowohl der Herstellungsprozeß einer Gipsstatue als auch der innere Zustand, wie Ergänzungen, Klebungen und Armierungen, festgestellt werden können. Aus den CT Bildern ergab sich eine für die vorher vermutete Gipszusammensetzung ungewöhnliche innere Struktur. Mit einer Freihand bedienten Röntgenpistole zur Messung der Röntgenfluoreszenz wurde daraufhin die Zusammensetzung des Materials der Statuette als Terracotta bestimmt. Durch den Einsatz von Helium als Spülmittel konnten auch leichte Materialien nachgewiesen und so eine Unterscheidung zwischen Gips und gebranntem Ton durchgeführt werden. Aus den CT Daten wurde eine virtuelle Darstellung der äußeren Geometrie gewonnen. Ein damit versuchsweise erstelltes Replik (Rapid Prototyping, 3D-Drucker, TU-Berlin) entsprach nicht den Anforderungen des Museums zur Erstellung einer Gußform für eine Bronzekleinserie der Statuette. Die zweite Statue, die 'Große Nacht' (1930) ist mit ihrer Größe von 2,12m und aufgrund des durch korrodierende Metallarmierung verursachten Schadensbildes nicht mehr transportfähig. Eine in-situ Untersuchung mit dem mobilen Tomographen, der in den 1980ern zur Untersuchung von Bäumen gebaut und jetzt mit einem modernen Flachdetektor und einer Röntgenröhre ausgestattet ist, wird vorgestellt. Die Möglichkeiten der in-situ CT für große Skulpturen werden anhand der Ergebnisse diskutiert. T2 - DGZfP-Jahrestagung 2010 CY - Erfurt, Deutschland DA - 2010-05-10 KW - Mobile CT KW - Mobile RFA PY - 2010 SN - 978-3-940283-26-9 IS - DGZfP-BB 122 (P12) SP - 1 EP - 8 CY - Berlin AN - OPUS4-24695 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weise, Frank A1 - Onel, Yener A1 - Goebbels, Jürgen T1 - Analyse des Gefüge- und Feuchtezustandes in mineralischen Baustoffen mit der Mikro-Röntgen-3D-Computertomografie KW - Beton KW - Naturstein KW - Schadensanalyse KW - Innovative Prüftechnik PY - 2007 SN - 0171-5445 SN - 1437-0980 VL - 29 IS - 3 SP - 194 EP - 201 PB - Ernst CY - Berlin AN - OPUS4-15688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Onel, Yener A1 - Goebbels, Jürgen T1 - Analyse des Gefüge- und Feuchtezustandes in mineralischen Baustoffen mit der Röntgen-3D-Computertomografie T2 - 12. Bauklimatisches Symposium CY - Dresden, Deutschland DA - 2007-03-29 PY - 2007 VL - 1 SP - 395 EP - 405 PB - TU Dresden CY - Dresden AN - OPUS4-14717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Weise, Frank A1 - Onel, Yener A1 - Maier, Bärbel ED - Stark, J. T1 - Zeitliche und räumliche Visualisierung des Gefügezustandes und der Transportvorgänge in frostbeanspruchten Normalbetonen T2 - 16. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2006-09-20 KW - Dauerhaftigkeit KW - Frostbeständigkeit KW - Beton KW - Schadensanalyse KW - Innovative Prüftechnik PY - 2006 SN - 3-00-018263-2 IS - Band 2 SP - 2-0701 - 2-0706 PB - Bauhaus-Univ. CY - Weimar AN - OPUS4-14398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Onel, Yener A1 - Finn, Monika A1 - Rehmer, Birgit T1 - Charakterisierung des oxidativen Schädigungsverhaltens infiltrierter faserverstärkter 2D-C/C-Keramiken mit Hilfe der Röntgencomputertomographie T2 - 15. Symposium Verbundwerkstoffe und Werkstoffverbunde CY - Kassel, Deutschland DA - 2005-04-06 KW - Schädigungsuntersuchung KW - Röntgencomputertomographie KW - Oxidation KW - Keramische Verbundwerkstoffe KW - Kohlenwerkstoffe PY - 2005 SP - 421 EP - 426 PB - DGM CY - Kassel AN - OPUS4-7622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Weise, Frank A1 - Onel, Yener A1 - Dehn, F. ED - Alexander, M. T1 - Application of X-ray tomography for the verification of damage mechanisms in concrete T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting CY - Cape Town, South Africa DA - 2005-11-21 KW - Bauwerkssicherheit KW - Betonbau KW - Strukturaufklärung KW - Zerstörungsfreie Prüfung KW - Röntgen 3D-CT PY - 2005 SN - 0-415-39654-9 N1 - Serientitel: Balkema proceedings and monographs in engineering, water and earth sciences – Series title: Balkema proceedings and monographs in engineering, water and earth sciences SP - 170 EP - 171 PB - Taylor & Francis CY - London AN - OPUS4-11595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Onel, Yener A1 - Dehn, F. T1 - Application of X-ray Tomography for the Verifikation of Damage Mechanism in Concrete T2 - Proceedings of the "International Conference on Concrete Repair, Rehabilitation and Retrofitting" CY - Cape Town, South Africa DA - 2005-11-21 PY - 2005 AN - OPUS4-10650 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Onel, Yener A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen T1 - 320 kV Mikrofokusröntgenröhre und Flächendetektor, eine Kombination für die 3D-CT? T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2003 CY - Mainz, Deutschland DA - 2003-05-26 PY - 2003 UR - http://www.ndt.net/article/dgzfp03/papers/v27/v27.htm SN - 3-931381-47-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 83-CD SP - 1 EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-2874 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Onel, Yener A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen T1 - Experiences in using a 320 kV micro focus X-ray tube and a large sized amorphous silicon detector for 3D-CT N2 - A novel 3D-CT scanner was set up at BAM to extend the applicability of the X-ray transmission microtomography (µ-CT) to specimens up to 30 cm in diameter. The scanner consists of a bipolar 320 kV micro focus tube and a flat panel detector of amorphous silicon. Minimisation of scattered radiation, control of room and system temperature, and corrective preprocessing on the projection data are necessary to achieve expectable CT images. Statistical evaluations to show the limits and results of CT investigations are reported. T2 - International Symposium on Computed Tomography and Image Processing for Industrial Radiology CY - Berlin, Germany DA - 2003-06-23 PY - 2003 UR - http://www.ndt.net/article/ct2003/v06/v06.htm SN - 3-931381-48-X N1 - Serientitel: DGZfP-Proceedings BB – Series title: DGZfP-Proceedings BB IS - 84-CD SP - 53 EP - 59 PB - DGZfP CY - Berlin AN - OPUS4-2875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Onel, Yener A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen T1 - 320kV Microfokusröntgenröhre und Flachdetektor, eine Kombination für die 3D-CT? T2 - DGZfP-Jahrestagung 2003: Zerstörungsfreie Materialprüfung - ZfP in Anwendung, Entwicklung und Forschung CY - Mainz, Germany DA - 2003-05-26 PY - 2003 AN - OPUS4-3805 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Onel, Yener A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen T1 - Experiences in using a 320kV micro focus X-ray tube and a large sized amorphous silicon detector for 3D-CT T2 - International Symposium on Computed Tomography and Image Processing for Industrial Radiology CY - Berlin, Germany DA - 2003-06-23 PY - 2003 AN - OPUS4-3810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Redmer, Bernhard A1 - Onel, Yener A1 - Ewert, Uwe T1 - Mechanised radiation techniques - an innovative technique of the mobile in-service inspection of circumferential welds T2 - 3rd International Conference "Pipeline Diagnostics" CY - Moscow, Russia DA - 2001-05-21 PY - 2001 SP - I34 AN - OPUS4-1176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Redmer, Bernhard A1 - Onel, Yener A1 - Ewert, Uwe A1 - Lunin, V. A1 - Podobedov, D. T1 - Mechanisierte Durchstrahlungsprüfung - Innovative Techniken zur Bewertung von Rundschweißnähten T2 - Tagung Schweißen und Schneiden ; Große Schweißtechnische Tagung CY - Essen, Deutschland DA - 2001-09-11 PY - 2001 SN - 3-87155-674-2 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 216 SP - 243 EP - 247 PB - Verl. für Schweißen und Verwandte Verfahren, DVS-Verl. CY - Düsseldorf AN - OPUS4-1162 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -