TY - CONF A1 - Wolff, Dietmar A1 - Jaunich, Matthias A1 - Stark, Wolfgang T1 - Investigating the performance of rubber seals at low temperatures N2 - Rubbers are widely used as main sealing materials for Containers for low and intermediate level radioactive waste and as additional component to metal seals in spent fuel and high active waste containers. The save enclosure of the radioactive container inventory has to be guaranteed according to legislation and appropriate guidelines for long term storage periods as well as down to temperatures of -40 °C for transportation. Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is necessary to ensure a proper material choice which is certainly also influenced by additional factors as e.g. the aging behavior. T2 - 14th International high-level radioactive waste management conference CY - Albuquerque, New Mexico, USA DA - 28.04.2013 KW - Rubber seals KW - Elastomers KW - Compression set KW - Low temperature KW - Leakage rate PY - 2013 SN - 978-1-62748-644-6 SP - 1 EP - 7(Paper # 6888) PB - Omnipress AN - OPUS4-28530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Sturm, Heinz A1 - Stark, Wolfgang A1 - Bovtun, V. A1 - Schulz, Eckhard ED - Xia, Z. T1 - Methods for simultaneous measurements of topography and local electrical properties using scanning force microscopy N2 - Two different approaches to investigate the local complex conductivity and the surface charge with Scanning Force Microscopy (SFM) techniques are presented. It is shown that the measurement of local electrical properties with SFM leads to interesting information about the composition of electrically heterogeneous surfaces T2 - 9th International Symposium on Electrets (ISE 9) CY - Shanghai, China DA - 1996-09-25 PY - 1996 SN - 0-7803-2695-4 DO - https://doi.org/10.1109/ISE.1996.578073 SP - 223 EP - 228 PB - IEEE Service Center CY - Piscataway, NJ AN - OPUS4-6851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Sturm, Heinz A1 - Schulz, Eckhard A1 - Stark, Wolfgang A1 - Bovtun, V. A1 - Friedrich, Jörg Florian ED - Olefjord, I. ED - Nyborg, L. ED - Briggs, D. T1 - Techniques for surface composition analysis with scanning force microscopy (SFM) using electrical surface properties T2 - 7th European Conference on Applications of Surface and Interface Analysis CY - Göteborg, Sweden DA - 1997-06-16 PY - 1997 SN - 0-471-97827-2 SP - 579 EP - 582 PB - Wiley CY - Chichester AN - OPUS4-6854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Straet, T. A1 - Bayerl, H. A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kürten, Ch. T1 - Ultrasonic Measurements on Thermoset Moulding Compounds KW - Ultraschall KW - Fertigungskontrolle KW - Schallgeschwindigkeit KW - Vernetzungsreaktion KW - Qualitätssicherung PY - 2005 SN - 0945-0084 VL - 95 IS - 7 SP - 1 EP - 5 PB - Hanser CY - München AN - OPUS4-10304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Braun, Ulrike A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich N2 - Faserverbundbauteile werden durch Tränkung von Fasergewebe mit flüssigem Harz, in der Regel Epoxidharzen, und anschließender Härtung des Harzes gefertigt. Dabei kann man das Gewebe im Vorfeld mit reaktivem Harz tränken und als so genanntes Prepreg verarbeiten oder man injiziert das frisch mit dem Härter gemischte Harz in ein Werkzeug, in dem das Gewebe bereits liegt - z. B. beim RTM-Prozess. Ausgehend von der Aufgabenstellung, eine Prepregherstellung mit hohem Qualitätsstandard zu realisieren und Möglichkeiten der Fertigungskontrolle für den Prepreg-Verarbeiter aufzuzeigen, wurde an einem für die Prepregherstellung vorgesehenen Harzsystem eine weitgehende Charakterisierung des Aushärtungsverlaufs vorgenommen. Wegen der Schwierigkeit, schnell konstante Aushärtungstemperaturen zu erreichen, wurden bei allen Methoden mit einer Heizrate von 1 K/min von RT bis 200 °C aufgeheizt. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 KW - Thermoanalyse KW - Lineare Aufheizung KW - Online Prozesskontrolle KW - Epoxidharz KW - Prepreg PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 1.1 SP - 1 EP - 9 AN - OPUS4-24910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Kürten, Ch. T1 - Prozessüberwachung bei duroplastischen Formmassen N2 - Dielektrische Sensoren überwachen den Vernetzungsprozess beim Spritzgießen direkt im Werkzeug. Der Aushärtungszustand wird kontinuierlich verfolgt, Abweichungen werden erkannt und die Zykluszeit optimiert. KW - Prozesskontrolle KW - Aushärtegrad KW - Kochversuch KW - Harnstoffformasse KW - Dielektrik PY - 2006 SN - 0023-5563 IS - 7 SP - 97 EP - 100 PB - Hanser CY - München AN - OPUS4-13084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Kürten, C. T1 - Verarbeitung von Harnstoff-Formmassen - Begleitende Online-Prozesskontrolle N2 - Harnstoff-Formmassen gehören zu den duroplastischen Formmassen, die im Werkzeug chemisch vernetzen und so ihre herausragende Temperaturbeständigkeit erreichen. Im Wettbewerb mit Thermoplasten weisen Formmassen den Nachteil auf, dass die Vernetzungsreaktion eine kritische Zeit bedingt, damit die Glasübergangstemperatur soweit verschoben werden kann, dass die heißen Teile stabil und blasenfrei entformt werden können. Die Zykluszeiten sind bei Formmassen daher deutlich höher als bei Thermoplasten. Eine Möglichkeit, die Zykluszeit zu verringern, wäre die Erhöhung der Werkzeugtemperatur, da bekanntlich eine Erhöhung der Reaktionstemperatur um 10 K zu einer Verdoppelung der Reaktionsgeschwindigkeit führt. Allerdings wird dabei das Zeitfenster für die Entformung optimal gehärteter Teile deutlich kleiner, der Prozess anfälliger gegen Schwankungen im Prozess und in der Formmasse-Zusammensetzung. Mit einer Online-Kontrolle des Vernetzungszustands sollte es aber gelingen, den Prozess auch bei einer höheren Werkzeugtemperatur noch stabil zu beherrschen. In der vorliegenden Arbeit wird die Methode der dielektrischen Prozesskontrolle in der Fertigung von Spritzgieß-Formteilen erprobt und die Möglichkeiten einer Prozesssteuerung werden herausgearbeitet. KW - Harnstoffharz KW - Elektroinstallationsteile KW - Aushärtungsverlauf KW - Kochversuch PY - 2008 SN - 0176-1625 VL - 61 IS - 12 SP - 790 EP - 793 PB - Gupta CY - Ratingen AN - OPUS4-18734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - McHugh, J. T1 - Cure state detection for pre-cured carbon-fibre epoxy prepreg (CFC) using temperature-modulated differential scanning calorimetry (TMDSC) N2 - Carbon-fibre prepregs have found widespread use in lightweight applications. They are based on a carbon-fibre fabric impregnated with reactive epoxy resin. Prepreg materials are generally pre-cured so that they have a higher molecular weight than typical resins in order to reduce resin flow, which facilitates storage and later processing properties. The measurements were carried out using commercially available materials and follow the published DMA investigations of the same material. TMDSC was used to find the correlation between curing conditions, the degree of cure and glass transition temperature. TMDSC has the advantage over standard DSC that it enables better determination of the glass transition temperature, which is often accompanied by an exothermic curing reaction, and thus overshadowed. The influence of the amplitude of temperature modulation was tested in preliminary experiments. For non-cured material a glass transition temperature of approximately 0 °C was determined; whereas for the totally cured material it was approximately 230 °C. The changes in degree of cure, temperature of actual glass transition and post-reaction are given as a function of curing time at 180 °C. The correlation between actual glass transition temperature and degree of cure is derived. KW - Prepreg KW - Carbon fibre KW - Glass transition KW - Degree of curing KW - DSC KW - TMDSC PY - 2013 DO - https://doi.org/10.1016/j.polymertesting.2013.07.007 SN - 0142-9418 VL - 32 IS - 7 SP - 1261 EP - 1272 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-29067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - McHugh, J. T1 - Carbon-fibre epoxy prepreg (CFC) curing in an autoclave analogue process controlled by dynamic mechanical analysis (DMA) N2 - Carbon fibre prepregs have found widespread application in lightweight constructions. They are based on a carbon-fibre fabric impregnated with reactive epoxy resin. DMA measurements under temperature conditions similar to an autoclave programme were carried out using commercially available prepreg material with a high glass transition temperature. The characteristic of the temperature programme was a dynamic heating segment at 1.5 K/min followed by a longer isothermal segment at 180 °C. The courses of the storage modulus E', loss modulus E'' and tanδ were recorded. The measuring frequency was varied between 1 Hz and 33.3 Hz. Gelation and vitrification are assigned. The influence of the measuring frequency on the time to vitrification and the correlation with DSC are discussed. The reaction does not end even after 10 h curing at 180 °C, which is interpreted as the slow cessation of the reaction caused by vitrification. KW - Prepreg KW - CFC KW - Curing KW - DMA KW - DSC KW - Autoclave KW - Gelation KW - Vitrification KW - Glass transition PY - 2013 DO - https://doi.org/10.1016/j.polymertesting.2013.09.014 SN - 0142-9418 VL - 32 IS - 8 SP - 1487 EP - 1494 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-29479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Mc Hugh, Jarlath T1 - Dynamic mechanical analysis (DMA) of epoxy carbon-fibre prepregs partially cured in a discontinued autoclave analogue process N2 - Epoxy carbon-fibre prepreg, Hexcel Type 6376 HTS, was investigated using Dynamic Mechanical Analysis (DMA). The DMA characteristic parameters are storage modulus E', loss modulus E' and loss factor tanδ. These parameters are ideally suited to observe the vitrification, referred to as glass transition, resulting from the cross-linking reaction. Detection of the cure state may also be achieved by determining the momentary glass transition temperature of partially cured samples. The consequent use of a multi-frequency measuring regime was used to derive the apparent activation energy for the glass transition process. Different temperature programs were also applied to monitor the curing process directly, as well as to investigate the different states of incomplete cure reached in preceding curing steps. The intention was to provide better understanding of the consequences of an interrupted autoclave curing process and to use DMA to detect the cure state achieved. With DMA, the continuation of an incomplete curing process also can be monitored. DMA measurements up to 300 °C showed, furthermore, that the final glass transition temperature was reduced by thermal degradation at high temperatures. KW - Composites KW - Epoxy KW - Cross-linking KW - Prepreg KW - Degree of cure KW - Glass transition PY - 2015 DO - https://doi.org/10.1016/j.polymertesting.2014.11.004 SN - 0142-9418 VL - 41 SP - 140 EP - 148 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-32325 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Bohmeyer, W. A1 - Lange, K. T1 - Investigation of the crosslinking behaviour of ehtylene vinyl acetate (EVA) for solar cell encapsulation by rheology and ultrasound N2 - EVA is a widely used material for the encapsulation of photovoltaic modules. It melts at elevated temperatures, and seals the module before it is crosslinked at temperatures above 130 °C by a peroxide-initiated crosslinking reaction. EVA has good optical properties necessary for application in solar modules. For process optimization and quality management, a method for the quick and reliable characterization of EVA crosslinking behaviour is of great value. Here, the practicability of ultrasound for online crosslinking monitoring is demonstrated. A sound velocity increase of about 8 m/s during the crosslinking reaction is found. The ultrasound results are compared with rheometer measurements performed with a curemeter typically used for the investigation of rubber crosslinking. KW - Ethylene vinyl acetate KW - EVA KW - Crosslinking KW - Ultrasound KW - Rheology KW - Curemeter KW - DSC PY - 2012 DO - https://doi.org/10.1016/j.polymertesting.2012.07.004 SN - 0142-9418 VL - 31 IS - 7 SP - 904 EP - 908 PB - Elsevier CY - Amsterdam AN - OPUS4-26291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias T1 - Investigation of ethylene/vinyl acetate copolymer (EVA) by thermal analysis DSC and DMA N2 - Two types of commercially applied Ethylene/Vinyl Acetate Copolymers (EVA) for encapsulation of photovoltaic modules were investigated by the thermal analysis methods of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) in the temperature range from -150 °C to 200 °C. Glass transition, crystal melting and cross-linking were analyzed. The aims of the investigations were to gain more information for incoming goods control and to get information about the whole temperature dependent material properties in the investigated temperature range, starting at very low temperatures up to the crosslinking temperature region. KW - EVA KW - Thermal analysis KW - DSC KW - DMA KW - Glass transition KW - Crystal melting KW - Cross-linking PY - 2011 DO - https://doi.org/10.1016/j.polymertesting.2010.12.003 SN - 0142-9418 VL - 30 IS - 2 SP - 236 EP - 242 PB - Elsevier Ltd. CY - Amsterdam [u.a.] AN - OPUS4-23206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias T1 - Thermoanalytische Charakterisierung von Ethylen-Vinylacetat-Copolymer (EVA) für Photovoltaikmodule N2 - Das Ziel der Untersuchungen war mit Hilfe von DSC und DMA EVA-Folien im Anlieferungszustand hinsichtlich der Lage der Glasübergangstemperatur, des Schmelzverhaltens und der Temperaturabhängigkeit der Vernetzungsreaktion zu charakterisieren. Auf dieser Basis sollte die Lieferstabilität im Sinne einer Wareneingangskontrolle auf eine messtechnische Basis gestellt werden. In einem 2. Schritt sollte die vernetzte Folie dahingehend charakterisiert werden, ob infolge der Vernetzung eine Änderung der KW - Photovoltaik KW - Klebfolie KW - EVA KW - DSC KW - DMA PY - 2011 VL - 8 SP - 3 EP - 5 AN - OPUS4-24168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Hoster, B. A1 - Kürten, Ch. T1 - Nachtemperung von duroplastischen Bauteilen - Spagat zwischen Eigenschaftsverbesserung und Eigenschaftsverschlechterung PY - 2005 SN - 0176-1625 VL - 58 IS - 11 SP - 718 EP - 722 PB - Gupta CY - Ratingen AN - OPUS4-11592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Hoster, B. A1 - Kürten, C. T1 - Längenänderung bei erhöhten Temperaturen und Aushärtegrad von duroplastischen Formteilen KW - Harnstoffharze KW - Verzug KW - Spritzgießen KW - Aushärtegrad KW - Schrumpf PY - 2006 SN - 0176-1625 VL - 59 IS - 10 SP - 627 EP - 631 PB - Gupta CY - Ratingen AN - OPUS4-14444 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, U. A1 - Bayerl, H. T1 - Online monitoring of thermoset post-curing by dynamic mechanical thermal analysis DMTA N2 - Thermosetting moulding compounds are synthetic materials which can be easily formed in the molten state and achieve high temperature stability due to a cross-linking process which takes place during manufacture. To ensure thermal and mechanical properties, post-curing of moulded phenolic resin components is necessary for high quality applications. In the industrial practice, post-curing time-temperature-programs are heuristically acquired. In this paper, dynamical mechanical thermal analysis is employed to determine optimal post-curing conditions for injection moulded parts from phenolic resin. KW - DMTA KW - Moulding compound KW - Thermoset KW - Phenolic resin KW - Post-curing PY - 2009 DO - https://doi.org/10.1016/j.polymertesting.2009.02.005 SN - 0142-9418 VL - 28 IS - 6 SP - 561 EP - 566 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-19822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Fritsch, Sebastian A1 - Kelm, Jürgen T1 - Vulcanization Monitoring in the Mould by Means of Ultrasound T2 - German Rubber Conference 2006 CY - Nuremberg, Germany DA - 2006-07-03 KW - Vulkanisation KW - Ultraschall KW - Prozesskontrolle KW - Rheologie PY - 2006 SP - 189 EP - 193 PB - Deutsche Kautschuk-Gesellschaft CY - Frankfurt am Main AN - OPUS4-13082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Walentowski, Heinz-Ulrich T1 - Crosslinking Instead of Glassy Transition N2 - In processing fibre-reinforced composites, the curing reaction can be significantly retarded if the temperature and reaction time are not optimally set. In such situations, complete curing is sometimes impossible under practically relevant conditions. It is difficult for processors to recognize or detect incomplete curing. The equilibrium glass transition temperature plays an important role in complete curing in the production process. PY - 2000 SN - 0945-0084 VL - 90 IS - 4 SP - 33 EP - 35 PB - Hanser CY - München AN - OPUS4-822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Walentowski, Heinz-Ulrich T1 - Vernetzen statt Verglasen PY - 2000 UR - http://www.kunststoffe.de/ku/default.asp SN - 0023-5563 VL - 90 IS - 4 SP - 90 EP - 92 PB - Hanser CY - München AN - OPUS4-823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kürten, C. T1 - Vernetzung reaktiver Kunststoffe mit Ultraschall überwachen KW - Elastomer KW - Epoxidharz KW - Phenolharz KW - Vernetzung KW - Vulkanisation KW - Schallgeschwindgkeit KW - Prozesskontrolle PY - 2008 SN - 0939-2629 SN - 0176-6058 IS - 2 SP - 31 EP - 33 PB - Holzverl. CY - Kissing AN - OPUS4-17587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen A1 - Fritsch, Sebastian ED - Green, R. E. ED - Djordjevic, B. B. ED - Hentschel, M. P. T1 - Rubber processing monitored by ultrasound T2 - 11th International Symposium on Nondestructive Characterization of Materials CY - Berlin, Germany DA - 2002-06-24 PY - 2003 SN - 3-540-40154-7 SP - 659 EP - 664 PB - Springer CY - Berlin AN - OPUS4-2769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen A1 - Fritsch, Sebastian T1 - Kontrolle der Kautschukvulkanisation im Werkzeug mit Ultraschall N2 - Zusammenfassung In diesem Beitrag wird zunächst die für die on-line Prozesskontrolle an duroplastischen Formmassen entwickelte Ultraschallmesstechnik vorgestellt. Die Methode basiert auf der Durchschallung des vernetzenden Materials mit Hilfe von in das Werkzeug integrierten druck- und temperaturfesten 4 MHz-Ultraschallsensoren. Die Auswertung von Schalllaufzeit und Signalamplitude erfolgt vollautomatisch und dient der Berechnung von Schallgeschwindigkeit und -dämpfung. Beide Größen repräsentieren die änderung der mechanischen Eigenschaften infolge der Vernetzungsreaktion. Durch Anwendung auf vulkanisierende Materialien sollte die Anwendbarkeit der bewährten Methode erweitert werden. Im Ergebnis wird gezeigt, dass die Größe des Messeffekts von der Menge an Vernetzer (Schwefelkonzentration) abhängt. Bei ausreichend hohem Vernetzungsgrad zeigt die Ultraschallgeschwindigkeit signifikante, gut auswertbare Resultate, die den Ablauf der Vulkanisation on-line zu verfolgen gestatten. Ein Vergleich mit Vulkameterkurven zeigt große ähnlichkeiten und berechtigt zu der Hoffnung, dass die Methode industriellen Einsatz finden kann. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Prozesskontrolle KW - Vulkanisation KW - Vulkameter KW - Ultraschall KW - Schallgeschwindigkeit PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/p21/p21.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen T1 - Ultraschall on-line Prozesskontrolle bei der Vulkanisation KW - Prozesskontrolle KW - Vulkanisation KW - Ultraschall KW - Sensoren KW - Schubmodul KW - Verlustmodul PY - 2000 SN - 0948-3276 SN - 0022-9520 SP - 9 Seiten PB - Hüthig CY - Heidelberg AN - OPUS4-997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Knappe, S. A1 - Mc Hugh, Jarlath A1 - Opfermann, J. T1 - Der RTM-Prozess und die Probleme von Gelierung, Verglasung und Aushärtegrad T2 - 6. Internationale AVK-TV Tagung für Verstärkte Kunststoffe und Duroplastische Formmassen ; 6th International AVK-TV Conference for Reinforced Plastics and Thermoset Moulding Compounds CY - Baden-Baden, Deutschland DA - 2003-10-07 KW - Epxidharz KW - Compositbauteil KW - Vernetzungsreaktion PY - 2003 VL - 6 SP - C14-1-C14-16 PB - AVK-TV CY - Frankfurt am Main AN - OPUS4-3034 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Stark, Wolfgang A1 - Bohmeyer, W. ED - Karbhari, V.M. T1 - Non-destructive evaluation (NDE) of composites: using ultrasound to monitor the curing of composites N2 - Typical composite materials for lightweight construction consist of a fibre (glass or carbon) reinforced thermosetting matrix. The impregnation of the fabric is made with liquid resin – usually epoxy resin or unsaturated polyester resin are used. The main processing methods are resin transfer moulding (RTM) and prepreg technology often used in combination with autoclave curing. After shaping, the resin must be cured. The final properties of the produced parts depend on the curing degree and the final glass transition temperature. Analytical methods and the use of ultrasound for online cure monitoring in the manufacturing process are introduced. Examples for the application of ultrasonic cure monitoring for the production of composite parts for traffic systems are also covered. KW - Epoxy KW - DSC KW - DMA KW - Kinetic KW - Autoclave KW - Curing KW - Glass transition KW - Curing behaviour KW - Curing degree KW - Rheology KW - Differential scanning calorimetry KW - Dynamic mechanical analysis KW - Sound velocity KW - Sound damping KW - Resin transfer moulding KW - RTM KW - Prepreg PY - 2013 SN - 978-0-85709-344-8 SN - 978-0-85709-355-4 DO - https://doi.org/10.1533/9780857093554.1.136 SN - 2052-5281 SN - 2052-529X N1 - Serientitel: Woodhead publishing sereies in composites science and engineering – Series title: Woodhead publishing sereies in composites science and engineering VL - 43 IS - Part 1 / Chapter 7 SP - 136 EP - 181 PB - Woodhead Publishing Ltd CY - Cambridge, UK AN - OPUS4-28848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Döring, Joachim A1 - Mc Hugh, Jarlath T1 - Making cure visible: monitoring the crosslinking process using integrated ultrasound sensors N2 - A special ultrasonic measuring system was developed to monitor the cross-linking process, enabling interaction with the manufacturing process in order to optimise part quality and reduce cycle times. KW - Thermoset KW - Ultrasound sensors KW - Mould KW - Rtm KW - Gelation KW - Vitrification PY - 2008 SN - 1639-965X IS - 38 SP - 64 EP - 66 PB - JEC CY - Paris AN - OPUS4-18610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Characterizing the flow-cure behaviour of thermoset plastics using thermoanalytical and ultrasonic methods N2 - The prospects of modern thermoanalytical methods for characterisation of flow, curing and final mechanical behaviour of moulding compounds were demonstrated. Using urea resin moulding compounds from different manufacturers the possibilities of the various techniques could be shown. With comparatively low effort, fundamental information can be gained before production process had been started. On this basis it is possible to make appropriate material selection at an early point in the process chain. On the basis of thermoanalytical data an incoming goods inspection can be established. Also it is easy to control the compliance with the conditions of delivery. In some cases it could also be helpful to have stored analysis data especially when problems appear in manufacturing process or unexpected part damages occur With the ultrasound measuring system it is possible to transfer the findings from the analytical methods directly to the processes in the mould. The application of ultrasound provides Dynamic Mechanical Analysis in the mould. Beside quality assurance ultrasound can also be used for process optimisation, especially for reduction of cycle time. In an advanced form ultrasound information can be used as a basis for improved machine control based on material state. The ultrasound measuring system developed by ISK Iserlohn and BAM can be obtained from the ISK. T2 - 5. Internationale Duroplasttagung / International Thermoset Conference CY - Iserlohn, Germany DA - 2008-11-20 KW - Differential Scanning Calorimetry KW - Dynamic Mechanical Analysis KW - Ultrasound KW - Urea rsin KW - Moulding compound KW - Incoming goods inspection KW - Process optimization PY - 2008 IS - Duro08_GB_08 SP - 1 EP - 8 AN - OPUS4-18586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Das Referenzelastomerprogramm der BAM T2 - Frühjahrstreffen der Bezirksgruppe Ost der Deutschen Kautschuk-Gesellschaft CY - Berlin, Germany DA - 2010-05-27 PY - 2010 AN - OPUS4-21393 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Simulation of cross-linking process of prepregs by dynamic mechanical analysis T2 - 11. Internationale Tagung "Arbeitsgemeinschaft verstärkte Kunststoffe AVK" CY - Essen, Germany DA - 2008-09-22 PY - 2008 AN - OPUS4-17946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Change of specific heat; thermal diffusity and thermal conductivity of a c-fibre prepreg during curing T2 - 15. Nationales Symposium SAMPE Deutschland CY - Berlin, Germany DA - 2009-02-18 PY - 2009 AN - OPUS4-18972 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Investigation of epoxy curing and determination of glass transition temperature by dynamic mechanical analysis (DMA) T2 - 15. Nationales Symposium SAMPE Deutschland CY - Berlin, Germany DA - 2009-02-18 PY - 2009 AN - OPUS4-18973 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stark, Wolfgang T1 - Historische Entwicklung der Überwachungsmethoden bei der Duroplastverarbeitung T2 - TECHNOMER 2009 - 21. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 2009-11-12 KW - Bakelit KW - Phenolharz KW - Isolierstoff KW - Gütesicherung KW - Prüfung PY - 2009 SN - 978-3-939382-09-6 IS - PQP4 SP - 1 EP - 9 AN - OPUS4-20399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang T1 - Entwicklung der Gütesicherung bei Isolierstoffen KW - Materialprüfungsamt KW - Kunstharze KW - Bakelit KW - Phenolharz KW - Aminoharz KW - Gütesicherung KW - Technische Vereinigung PY - 2010 UR - https://www.google.de/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwivis-l7tvKAhVFWBoKHa-jD1gQFggeMAA&url=https%3A%2F%2Fwww.kunststoffe.de%2F_storage%2Fasset%2F538701%2Fstorage%2Fmaster%2Ffile%2F5804889%2Fdownload%2FEntwicklung%2520der%2520G%25C3%25BCtesicherung%2520bei%2520Isolierstoffen.pdf&usg=AFQjCNE14vu5Aw1foQ7OZdcTT2vwsRX_TQ SN - 0023-5563 VL - 100 IS - 2 SP - 14 EP - 17 PB - Hanser CY - München AN - OPUS4-20935 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang T1 - Development of quality assurance for insulating materials PY - 2010 UR - https://www.google.de/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwjyyejZ7tvKAhXBVxoKHeV0Dr4QFgghMAA&url=https%3A%2F%2Fwww.kunststoffe.de%2Fen%2F_storage%2Fasset%2F590842%2Fstorage%2Fmaster%2Ffile%2F6128237%2Fdownload%2FDevelopment%2520of%2520Quality%2520Assurance%2520for%2520Insulating%2520Materials.pdf&usg=AFQjCNGMbKTaYDrHEdGuZ2IB_7zQCrTVkw SN - 1862-4243 VL - 100 IS - 2 SP - 6 EP - 9 PB - Hanser CY - München AN - OPUS4-20936 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang T1 - Investigation of curing behaviour of melamine/phenolic (MP) thermosets N2 - Commercially available melamine/phenolic (MP) moulding compounds used for manufacturing electro installation parts were investigated by laboratory thermal analysis methods: Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC) and Dielectric Analysis (DEA). The results were compared with on-line measurements in a compression mould using incorporated dielectric and ultrasound sensors. Softening and cross-linking behaviour were analyzed. For on-line process monitoring, only the ultrasound method worked well. The dielectric method was distorted by water formed as a by-product from the poly-condensation reaction. KW - Thermoset KW - Melamine KW - Phenol KW - Moulding compound KW - Cross-linking KW - DSC PY - 2010 DO - https://doi.org/10.1016/j.polymertesting.2010.05.008 SN - 0142-9418 VL - 29 IS - 6 SP - 723 EP - 728 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-20982 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Kontrolle des Vernetzungsverhaltens von reaktiven Kunststoffen T2 - 2. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2010-03-11 PY - 2010 AN - OPUS4-21011 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Kontrolle der Härtung bei reaktiven Formmassen und Faserverbundbauteilen T2 - 2. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2010-03-11 PY - 2010 AN - OPUS4-21015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Die Rolle des Staatlichen Materialprüfungsamtes Berlin-Dahlem bei der Typisierung der Pressmassen und der Gütesicherung T2 - 6th International Thermoset Conference CY - Iserlohn, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Characterisation of Flow and Curing Behaviour of Thermosetting Materials by Thermoanalytical and Ultrasound Methods T2 - 5th International Thermoset Conference Iserlohn CY - Iserlohn, Germany DA - 2008-11-21 PY - 2008 AN - OPUS4-18428 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Ultraschallmesstechnik zur Wareneingangskontrolle und zur Überwachung T2 - 5th Int. Thermoset Conference CY - Iserlohn, Germany DA - 2008-11-20 PY - 2008 AN - OPUS4-18468 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Elastomere Referenzmaterialien und ausgewählte Prüfverfahren T2 - DVM-Tag 2009 Elastomere CY - Berlin, Germany DA - 2009-04-22 PY - 2009 AN - OPUS4-19291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Kontrolle der Härtungsreaktion bei Faserverbundbauteilen T2 - 10. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2010-09-08 PY - 2010 AN - OPUS4-21930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Charakterisierung des Aushärtungsverhaltens von vernetzenden Kunststoffen - vom Labor in die Fertigung T2 - Vortragsveranstaltung Fraunhofer Institut für angewandte Polymerforschung (IAP) CY - Potsdam, Germany DA - 2010-10-08 PY - 2010 AN - OPUS4-22114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Ultrasound measuring system for flow front and cure monitoring at composite manufacturing (RTM, prepreg, injection moulding) T2 - Composite Europe, 5. Europäische Fachmesse und Forum für Verbundstoffe, Technologie und Anwendungen CY - Essen, Germany DA - 2010-09-14 PY - 2010 AN - OPUS4-22102 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Dielektrische Online-Prozesskontrolle bei Formmassen T2 - Dielektrik-Seminar und Workshop der Fa. Netzsch CY - Selb, Germany DA - 2003-03-19 PY - 2003 AN - OPUS4-3227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Der RTM-Prezess und die Probleme von Gelierung, Verglasung und Aushärtegrad T2 - Jahrestagung des AVK-TV 2003 CY - Baden-Baden, Germany DA - 2003-10-06 PY - 2003 AN - OPUS4-4555 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Charakterisierung duroplastischer Formmassen mit thermoanalytischen Methoden T2 - Frühjahrstagung des Fachverbandes Polymerphysik der Deutschen Physikalischen Gesellschaft (DPG) und Rheologentagung CY - Leipzig, Germany DA - 1999-03-01 PY - 1999 AN - OPUS4-5748 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Formmassen: Ultraschall zur Warenausgangs- und Wareneingangskontrolle T2 - 3rd International Thermoset Conference CY - Iserlohn, Germany DA - 2005-04-21 PY - 2005 AN - OPUS4-7352 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - "Sehende" Nachtemperung: Praktische Anwendung der Methode der Dynamisch Mechanischen Analyse (DMA) T2 - 3rd International Thermoset Conference CY - Iserlohn, Germany DA - 2005-04-21 PY - 2005 AN - OPUS4-7353 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Untersuchungen zum Aushärteverhalten und zum Aushärtungszustand von Epoxidharz T2 - VII Internationale AVK-TV Konferenz CY - Baden-Baden, Germany DA - 2004-09-28 PY - 2004 AN - OPUS4-4759 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -