TY - JOUR A1 - Rabe, Torsten A1 - Eberlee, Ina A1 - Güther, Wolfgang A1 - Stark, Wolfgang T1 - Mechanische und thermomechanische Charakterisierung keramischer Grünfolien KW - Keramische Grünfolien KW - Mechanische Prüfung KW - DMTA PY - 2004 SN - 0173-9913 SN - 0196-6219 VL - 18 IS - 1 SP - 58 EP - 68 PB - Göller CY - Baden-Baden AN - OPUS4-5338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Buchholz, Uwe A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Habel, Wolfgang A1 - Petersson, B.A.T. T1 - Acoustic data of cross linked polyethylene (XLPE) and cured liquid silicone rubber (LSR) by means of ultrasonic and low frequency DMTA N2 - Partial discharges may cause damage to electrical insulation of high voltage equipment. They initiate elastic waves in the insulating material, e.g. in the stress cone of an outdoor termination. Localisation of the origin of such elastic waves can help to predict serious damaging processes in the electrical insulation. In order to measure and evaluate the wave propagation effects in typical multilayered elastomeric structures, knowledge of the material properties is required. The propagating velocity and the attenuation of longitudinal waves are important parameters. Values for these quantities found in the literature were not appropriate. Therefore, for cross-linked polyethylene (XLPE) and cured liquid silicone rubber (LSR), the longitudinal wave velocity and the attenuation were evaluated in the temperature interval from -20°C to 50°C and in the frequency range from 200 kHz to 600 kHz using a two-sample ultrasound technique. The loss factor was determined from these measured quantities. Additionally, low frequency Dynamic Mechanical Thermal Analysis (DMTA) was applied to investigate LSR and XLPE in a temperature interval between -100 and 50°C and to check qualitatively the ultrasound data. KW - Acoustic propagation KW - Cross linked polyethylene insulation KW - Mechanical variables measurement KW - Silicone rubber PY - 2012 U6 - https://doi.org/10.1109/TDEI.2012.6180250 SN - 1070-9878 SN - 0018-9367 SN - 1558-4135 VL - 19 IS - 2 SP - 558 EP - 566 PB - Institute of Electrical and Electronics Engineers CY - New York, NY AN - OPUS4-26106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Fritsch, Sebastian A1 - Stark, Wolfgang A1 - Kelm, Jürgen ED - Kühnert, I. T1 - Möglichkeiten der Online-Kontrolle der Vulkanisation mit Ultraschall T2 - 18. TECHNOMER 2003 ; 18. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 2003-11-13 KW - Kautschuk KW - Vulkanisation KW - Ultraschall PY - 2003 SN - 3-00-012510-8 SP - 1 EP - 10 PB - Techn. Univ. CY - Chemnitz AN - OPUS4-2822 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Walentowski, Heinz-Ulrich T1 - Crosslinking Instead of Glassy Transition N2 - In processing fibre-reinforced composites, the curing reaction can be significantly retarded if the temperature and reaction time are not optimally set. In such situations, complete curing is sometimes impossible under practically relevant conditions. It is difficult for processors to recognize or detect incomplete curing. The equilibrium glass transition temperature plays an important role in complete curing in the production process. PY - 2000 SN - 0945-0084 VL - 90 IS - 4 SP - 33 EP - 35 PB - Hanser CY - München AN - OPUS4-822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Walentowski, Heinz-Ulrich T1 - Vernetzen statt Verglasen PY - 2000 UR - http://www.kunststoffe.de/ku/default.asp SN - 0023-5563 VL - 90 IS - 4 SP - 90 EP - 92 PB - Hanser CY - München AN - OPUS4-823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen A1 - Fritsch, Sebastian T1 - Kontrolle der Kautschukvulkanisation im Werkzeug mit Ultraschall N2 - Zusammenfassung In diesem Beitrag wird zunächst die für die on-line Prozesskontrolle an duroplastischen Formmassen entwickelte Ultraschallmesstechnik vorgestellt. Die Methode basiert auf der Durchschallung des vernetzenden Materials mit Hilfe von in das Werkzeug integrierten druck- und temperaturfesten 4 MHz-Ultraschallsensoren. Die Auswertung von Schalllaufzeit und Signalamplitude erfolgt vollautomatisch und dient der Berechnung von Schallgeschwindigkeit und -dämpfung. Beide Größen repräsentieren die änderung der mechanischen Eigenschaften infolge der Vernetzungsreaktion. Durch Anwendung auf vulkanisierende Materialien sollte die Anwendbarkeit der bewährten Methode erweitert werden. Im Ergebnis wird gezeigt, dass die Größe des Messeffekts von der Menge an Vernetzer (Schwefelkonzentration) abhängt. Bei ausreichend hohem Vernetzungsgrad zeigt die Ultraschallgeschwindigkeit signifikante, gut auswertbare Resultate, die den Ablauf der Vulkanisation on-line zu verfolgen gestatten. Ein Vergleich mit Vulkameterkurven zeigt große ähnlichkeiten und berechtigt zu der Hoffnung, dass die Methode industriellen Einsatz finden kann. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Prozesskontrolle KW - Vulkanisation KW - Vulkameter KW - Ultraschall KW - Schallgeschwindigkeit PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/p21/p21.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Dielektrische Online-Prozesskontrolle bei Formmassen T2 - Dielektrik-Seminar und Workshop der Fa. Netzsch CY - Selb, Germany DA - 2003-03-19 PY - 2003 AN - OPUS4-3227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Mc Hugh, Jarlath A1 - Bartusch, Jürgen T1 - Ultrasound on-line cure monitoring for industrial applications N2 - In recent years eure monitoring with ultrasonic methods became more important. An on-line measurement System for industrial applications is presented in this paper. It operates in through-transmission and the measured parameters are the sound velocity and the attenuation of the sound wave. An objective of this paper is to establish the ränge of possible applications for an ultrasonic eure monitoring System. KW - Ultrasonic monitoring KW - Cure process KW - Composite material KW - Process controlling PY - 2000 SN - 0963-6935 PB - Woodhead Publ. CY - Cambridge AN - OPUS4-1061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bovtun, Viktor Petrovic A1 - Stark, Wolfgang A1 - Kelm, Jürgen A1 - Porokhonskyy, V. A1 - Yakimenko, Y. T1 - Microwave Dielectric Properties of Rubber Compounds Undergoing Vulcanisation - Part 1. Natural rubber with and without carbon black filler KW - Dielectric parameters KW - Microwave methods KW - Vulcanisation KW - Elastomers KW - Monitoring PY - 2000 SN - 0948-3276 SN - 0022-9520 PB - Hüthig CY - Heidelberg AN - OPUS4-1062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen T1 - Ultraschall on-line Prozesskontrolle bei der Vulkanisation KW - Prozesskontrolle KW - Vulkanisation KW - Ultraschall KW - Sensoren KW - Schubmodul KW - Verlustmodul PY - 2000 SN - 0948-3276 SN - 0022-9520 SP - 9 Seiten PB - Hüthig CY - Heidelberg AN - OPUS4-997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -