TY - JOUR A1 - Rabe, Torsten A1 - Eberlee, Ina A1 - Güther, Wolfgang A1 - Stark, Wolfgang T1 - Mechanische und thermomechanische Charakterisierung keramischer Grünfolien KW - Keramische Grünfolien KW - Mechanische Prüfung KW - DMTA PY - 2004 SN - 0173-9913 SN - 0196-6219 VL - 18 IS - 1 SP - 58 EP - 68 PB - Göller CY - Baden-Baden AN - OPUS4-5338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Buchholz, Uwe A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Habel, Wolfgang A1 - Petersson, B.A.T. T1 - Acoustic data of cross linked polyethylene (XLPE) and cured liquid silicone rubber (LSR) by means of ultrasonic and low frequency DMTA N2 - Partial discharges may cause damage to electrical insulation of high voltage equipment. They initiate elastic waves in the insulating material, e.g. in the stress cone of an outdoor termination. Localisation of the origin of such elastic waves can help to predict serious damaging processes in the electrical insulation. In order to measure and evaluate the wave propagation effects in typical multilayered elastomeric structures, knowledge of the material properties is required. The propagating velocity and the attenuation of longitudinal waves are important parameters. Values for these quantities found in the literature were not appropriate. Therefore, for cross-linked polyethylene (XLPE) and cured liquid silicone rubber (LSR), the longitudinal wave velocity and the attenuation were evaluated in the temperature interval from -20°C to 50°C and in the frequency range from 200 kHz to 600 kHz using a two-sample ultrasound technique. The loss factor was determined from these measured quantities. Additionally, low frequency Dynamic Mechanical Thermal Analysis (DMTA) was applied to investigate LSR and XLPE in a temperature interval between -100 and 50°C and to check qualitatively the ultrasound data. KW - Acoustic propagation KW - Cross linked polyethylene insulation KW - Mechanical variables measurement KW - Silicone rubber PY - 2012 DO - https://doi.org/10.1109/TDEI.2012.6180250 SN - 1070-9878 SN - 0018-9367 SN - 1558-4135 VL - 19 IS - 2 SP - 558 EP - 566 PB - Institute of Electrical and Electronics Engineers CY - New York, NY AN - OPUS4-26106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Goering, Harald A1 - Stark, Wolfgang A1 - Bayerl, H. A1 - Brinkmann, P. T1 - Thermoanalytische Untersuchungen zur Phenolharzhärtung unter hohem Druck - Ein Weg zur Optimierung der Nachtemperung T2 - 3rd International Thermoset Conference CY - Iserlohn, Deutschland DA - 2005-04-21 KW - Post curing KW - High pressure DSC KW - DMA KW - Reaction kinetic KW - Phenolic resin PY - 2005 SP - 107 EP - 114 PB - Fachhochschule Südwestfalen - Hochschule für Technik und Wirtschaft CY - Iserlohn AN - OPUS4-7452 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Goering, Harald A1 - Stark, Wolfgang A1 - Bayerl, H. A1 - Brinkmann, P. T1 - Thermo Analytical Investigations of Phenol Moulding Compound Curing - Potential for Post-Cure Optimisation T2 - 3rd International Thermoset Conference CY - Iserlohn, Germany DA - 2005-04-21 KW - Post curing KW - High pressure DSC KW - DMA KW - Reaction kinetic KW - Phenolic resin PY - 2005 SP - 219 EP - 225 PB - Fachhochschule Südwestfalen - Hochschule für Technik und Wirtschaft CY - Iserlohn AN - OPUS4-7453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Fengler, Petra A1 - Michel, Uwe T1 - Optimierung der Nachtemperung von Formteilen für den Einsatz am heißen Motor mit Hilfe der Dynamisch Mechanischen Analyse T2 - 9. Anwendertreffen Dynamisch Mechanische Analyse CY - Selb, Germany DA - 2006-02-14 PY - 2006 AN - OPUS4-12113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Mielke, Werner A1 - Kunze, Ralf T1 - Charakterisierung duroplastischer Formmassen mit thermoanalytischen Methoden T2 - Frühjahrstagung des Fachverbandes Polymerphysik der Deutschen Physikalischen Gesellschaft (DPG) und Rheologentagung CY - Leipzig, Germany DA - 1999-03-01 PY - 1999 AN - OPUS4-5748 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Mc Hugh, Jarlath A1 - Straet, T. A1 - Bayerl, H. A1 - Kürten, Ch. T1 - Online Überwachung des Spritzgießprozesses mit Hilfe von Ultraschall T2 - 8. Internationale Tagung der Arbeitsgemeinschaft Verstärkte Kunststoffe-Technische Vereinigung e. V. (AVK-TV) CY - Baden-Baden, Germany DA - 2005-09-27 PY - 2005 AN - OPUS4-11622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Bayerl, H. A1 - Hoster, B. T1 - Post-annealing of thermosets T2 - 4th International Thermoset Conference CY - Iserlohn, Germany DA - 2006-11-16 PY - 2006 AN - OPUS4-13801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, Uwe T1 - Thermoanalyse der Phenolharzhärtung - Ein Weg zur Optimierung der Nachtemperung N2 - Angesichts der spezifischen Bedeutung der Aushärtung von Phenolharzen für ihre Eigenschaften als Ingenieurwerkstoffe besteht großes Interesse an deren quantitativer Charakterisierung. Mittels DSC-Messungen unter hohem Druck (HP-DSC) kann die Vernetzungsreaktion der Phenolharzformmassen durch die Unterdrückung der Verdampfung niedermolekularer Substanzen ohne störende Überlagerungen verfolgt werden. Mittels verschiedener Vernetzungsgrade können die Einflussparameter der Aufheizrate und der Nachtemperung optimiert werden. Die Messergebnisse ermöglichen eine Modellierung der Reaktionskinetik mit dem Ziel einer verbesserten Prozessführung und Qualitätskontrolle in der industriellen Praxis. KW - Phenolharze KW - Thermische Analyse KW - DMA KW - DSC KW - Aushärtung KW - Glasübergang PY - 2006 SN - 0025-5300 VL - 48 IS - 11-12 SP - 556 EP - 561 PB - Carl Hanser Verlag CY - München AN - OPUS4-13802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Dielektric Process Monitoring of Thermosetting Resins T2 - DEA-Seminar, Achema-Messe CY - Frankfurt am Main, Germany DA - 2003-05-22 PY - 2003 AN - OPUS4-4071 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Mc Hugh, Jarlath A1 - Opfermann, J. A1 - Knappe, S. T1 - The RTM-Process and the Problems with Gelation, Vitrification and Degree of Curing T2 - 6th Internationale AVK-Tv Conference CY - Baden-Baden, Germany DA - 2003-09-07 PY - 2003 AN - OPUS4-4072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Schulze, Dietmar A1 - Fengler, Petra A1 - Kelm, Jürgen T1 - Bestimmung der Glasübergangstemperatur von Elastomerdichtungen mit der Dynamisch Mechanischen Analyse DMA - Betrachtungen zur Temperatur-Messgenauigkeit T2 - DMA 242 - Users meeting CY - Selb, Germany DA - 2003-11-26 PY - 2003 AN - OPUS4-4075 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cappella, Brunero A1 - Stark, Wolfgang T1 - Adhesion of amorphous polymers as a function of temperature probed with AFM force-distance curves N2 - Force–displacement curves have been obtained with a commercial atomic force microscope at different temperatures and probe rates on a thick film of poly(n-butyl methacrylate) and on two films of polystyrene with different molecular weight. In a previous publication [B. Cappella, S.K. Kaliappan, H. Sturm, Macromolecules 38 (2005)1874] the analysis of force–displacement curves has been focused on the stiffness and on the Young's modulus of the samples. In the present publication we consider the temperature dependence of the work of adhesion. We have obtained master curves of the work of adhesion at fixed maximum loads and, by comparing the results of the two analysis, we show that the work of adhesion follows the Williams–Landel–Ferry equation with the same coefficients previously found for the Young's modulus. Furthermore, we show that the temperature dependence of the work of adhesion of the polymers is a consequence of the temperature dependence of the tip–sample contact area and in the end of the temperature dependence of the stiffness and of the elastic–plastic properties of the samples. KW - Atomic force microscope KW - Force-distance curves KW - Indentation KW - Elastic-plastic properties KW - Adhesion KW - Time-temperature superposition principle KW - Glass transition temperature PY - 2005 DO - https://doi.org/10.1016/j.jcis.2005.09.043 SN - 0021-9797 SN - 1095-7103 SP - 1 EP - 8(?) PB - Elsevier CY - Orlando, Fla. AN - OPUS4-11187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Mc Hugh, Jarlath T1 - Kontrolle von Aushärtungsverlauf und Aushärtegrad mittels dynamisch mechanischer Analyse und Ultraschall T2 - Rohima - Die deutsche FVK-Messe - Marktplatz Forschung CY - Leipzig, Germany DA - 2006-06-27 PY - 2006 AN - OPUS4-12528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Krüger, Simone A1 - Mc Hugh, Jarlath A1 - Kürten, Ch. A1 - Hoster, B. T1 - Charakterisierung von Aushärtungsverlauf und Aushärtungszustand in Labor und Fertigung T2 - Rohima - Die deutsche FVK-Messe - Marktplatz Forschung CY - Leipzig, Germany DA - 2006-06-27 PY - 2006 AN - OPUS4-12534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Döring, Joachim A1 - Mc Hugh, Jarlath A1 - Kürten, Ch. A1 - Lange, K. T1 - Kontrolle des Aushärtungsverlaufs im Werkzeug mit Hilfe von Ultraschall T2 - Rohima - Die deutsche FVK-Messe, Marktplatz Forschung CY - Leipzig, Germany DA - 2006-06-27 PY - 2006 AN - OPUS4-12535 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bovtun, Viktor Petrovic A1 - Stark, Wolfgang A1 - Kelm, Jürgen A1 - Pashkov, V.M. A1 - Yakimenko, Y. T1 - Characterization of carbon black filled rubber compounds by the Microwave Coaxial Method KW - Dielectric parameters KW - Microwave methods KW - Filled rubber compounds KW - Vulcanisation PY - 2005 SN - 0025-5300 VL - 47 IS - 3 SP - 118 EP - 122 PB - Carl Hanser Verlag CY - München AN - OPUS4-7273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Göring, H. A1 - Mc Hugh, Jarlath A1 - Opfermann, J. A1 - Knappe, S. T1 - Der RTM-Prezess und die Probleme von Gelierung, Verglasung und Aushärtegrad T2 - Jahrestagung des AVK-TV 2003 CY - Baden-Baden, Germany DA - 2003-10-06 PY - 2003 AN - OPUS4-4555 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mielke, Werner A1 - Stark, Wolfgang T1 - Unter Kontrolle - Aushärtung duroplastischer Formmassen PY - 1995 SN - 0047-3766 VL - 29 SP - 35 EP - 37 PB - Verl. Moderne Industrie CY - Landsberg AN - OPUS4-11798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, Uwe A1 - Krüger, Simone A1 - Bayerl, H. A1 - Kürten, Ch. T1 - Optimierung der Nachtemperung von Formteilen mit Hilfe von Thermo- und dynamisch mechanischer Analyse T2 - 8. Internationale Tagung der Arbeitsgemeinschaft Verstärkte Kunststoffe - Technische Vereinigung e. V. (AVK-TV) CY - Baden-Baden, Germany DA - 2005-09-27 PY - 2005 AN - OPUS4-10989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Fritsch, Sebastian A1 - Kelm, Jürgen T1 - Vulcanization Monitoring in the Mould by Means of Ultrasound T2 - German Rubber Conference 2006 CY - Nuremberg, Germany DA - 2006-07-03 KW - Vulkanisation KW - Ultraschall KW - Prozesskontrolle KW - Rheologie PY - 2006 SP - 189 EP - 193 PB - Deutsche Kautschuk-Gesellschaft CY - Frankfurt am Main AN - OPUS4-13082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Kürten, Ch. T1 - Prozessüberwachung bei duroplastischen Formmassen N2 - Dielektrische Sensoren überwachen den Vernetzungsprozess beim Spritzgießen direkt im Werkzeug. Der Aushärtungszustand wird kontinuierlich verfolgt, Abweichungen werden erkannt und die Zykluszeit optimiert. KW - Prozesskontrolle KW - Aushärtegrad KW - Kochversuch KW - Harnstoffformasse KW - Dielektrik PY - 2006 SN - 0023-5563 IS - 7 SP - 97 EP - 100 PB - Hanser CY - München AN - OPUS4-13084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolff, Dietmar A1 - Jaunich, Matthias A1 - Stark, Wolfgang T1 - Investigating the performance of rubber seals at low temperatures N2 - Rubbers are widely used as main sealing materials for Containers for low and intermediate level radioactive waste and as additional component to metal seals in spent fuel and high active waste containers. The save enclosure of the radioactive container inventory has to be guaranteed according to legislation and appropriate guidelines for long term storage periods as well as down to temperatures of -40 °C for transportation. Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is necessary to ensure a proper material choice which is certainly also influenced by additional factors as e.g. the aging behavior. T2 - 14th International high-level radioactive waste management conference CY - Albuquerque, New Mexico, USA DA - 28.04.2013 KW - Rubber seals KW - Elastomers KW - Compression set KW - Low temperature KW - Leakage rate PY - 2013 SN - 978-1-62748-644-6 SP - 1 EP - 7(Paper # 6888) PB - Omnipress AN - OPUS4-28530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Trappe, Volker T1 - Kinetic Model for Cross-linking Reaction of Epoxy Resin for Rotor Blade Production T2 - Thermosets Conference 2013 - From Monomers to Components CY - Berlin, Germany DA - 2013-09-18 PY - 2013 AN - OPUS4-28701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Braun, Ulrike A1 - Teteris, Gundars A1 - Bohmeyer, W. A1 - McHugh, J. T1 - Characterisation of curing behaviour of epoxy resin - from incoming goods control to on-line process monitoring T2 - Thermosets Conference 2013 - From Monomers to Components CY - Berlin, Germany DA - 2013-09-18 PY - 2013 AN - OPUS4-28702 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Low temperature - For a seal this depends on the applied material T2 - DKT 2012 - German Rubber Conference CY - Nuremberg, Germany DA - 2012-07-02 PY - 2012 IS - 10-2330_5-L-1530 SP - 1 EP - 4 PB - Deutsche Kautschuk-Gesellschaft CY - Frankfurt am Main AN - OPUS4-26190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Behaviour of rubber seals at low temperatures - results of component tests - N2 - The investigation of low temperature properties of elastomeric sealing materials by means of thermo-analytical methods is a sound way to get information about the glass transition process. The breakdown temperature of the sealing function of O-ring seals was measured in a component test setup depending on material and degree of compression. An in depth explanation of the observed component tests behaviour is currently in preparation. It requires the results of thermo-analytical methods and measurements as the compression set (not shown here). With that, a model was developed to describe the correlation between physical material parameters and observed component behaviour. T2 - Jahrestagung Kerntechnik 2013 CY - Berlin, Germany DA - 14.05.2013 PY - 2013 SP - 1 EP - 6 AN - OPUS4-28574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Wolff, Dietmar T1 - Investigation the sealing behaviour of rubber seals at low temperatures T2 - 11. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Wolff, Dietmar T1 - Characterization of the low temperature behaviour of rubber sealing materials T2 - 22. Fachtagung TECHNOMER 2011 CY - Chemnitz, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Braun, Ulrike A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich N2 - Faserverbundbauteile werden durch Tränkung von Fasergewebe mit flüssigem Harz, in der Regel Epoxidharzen, und anschließender Härtung des Harzes gefertigt. Dabei kann man das Gewebe im Vorfeld mit reaktivem Harz tränken und als so genanntes Prepreg verarbeiten oder man injiziert das frisch mit dem Härter gemischte Harz in ein Werkzeug, in dem das Gewebe bereits liegt - z. B. beim RTM-Prozess. Ausgehend von der Aufgabenstellung, eine Prepregherstellung mit hohem Qualitätsstandard zu realisieren und Möglichkeiten der Fertigungskontrolle für den Prepreg-Verarbeiter aufzuzeigen, wurde an einem für die Prepregherstellung vorgesehenen Harzsystem eine weitgehende Charakterisierung des Aushärtungsverlaufs vorgenommen. Wegen der Schwierigkeit, schnell konstante Aushärtungstemperaturen zu erreichen, wurden bei allen Methoden mit einer Heizrate von 1 K/min von RT bis 200 °C aufgeheizt. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 KW - Thermoanalyse KW - Lineare Aufheizung KW - Online Prozesskontrolle KW - Epoxidharz KW - Prepreg PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 1.1 SP - 1 EP - 9 AN - OPUS4-24910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich T2 - Technomer - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24900 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Characterization of the low temperature behaviour of rubber sealing materials N2 - Rubbers are often used for seal applications due to their special material properties and easy use. In many applications the material is exposed to low temperatures during Operation. Therefore it is important to know the material behavior at low temperatures to determine the temperature ränge that allows a Safe Operation of the seal, e.g. in storage and transport Containers for radioactive materials. The seal function of an elastomer is limited in temperature by the rubber-glass transition during which the material properties change from rubber-like to stiff and glass-like. For a given application this correlation is not trivial and therefore needs an in-depth investigation under consideration of the physical properties and the application conditions. In this work different analytical methods are used to characterize the material behavior at low temperature in the ränge of the glass-rubber-transition and are compared with the quality of Operation of a component which is here defined by the detected leakage rate. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 3.7 SP - 1 EP - 4 AN - OPUS4-24971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang T1 - Investigation of the curing behaviour of carbon fibre epoxy prepreg by dynamic mechanical analysis DMA N2 - Carbon fibre prepregs have found widespread application in lightweight constructions. They are based on a carbon fibre fabric impregnated with reactive epoxy resin. Measurements were carried out using commercially available prepreg material. For Dynamic Mechanical Analysis (DMA), a single cantilever measuring device was applied. The DMA results were refined by additional DSC measurements. The measurements were carried out with dynamic heating in the temperature range -90 to 280 °C. The heating rates were 1 and 2 K/min, respectively. A glass transition of the uncured material (Tg0) near 1 °C, and crosslinking-induced vitrification and devitrification at the maximal glass transition temperature of the cured material (Tgmax) in the temperature range 220 to 230 °C were found. The activation energies for the glass transitions were determined using an Arrhenius plot. By detailed consideration of the influence of the frequency on the DMA data, indications for gelation were deduced. KW - CRP KW - Prepreg KW - Carbon fibre KW - Epoxy KW - DMA KW - DSC KW - Glass transition KW - Crosslinking KW - Vitrification KW - Devitrification PY - 2013 DO - https://doi.org/10.1016/j.polymertesting.2012.11.004 SN - 0142-9418 VL - 32 IS - 2 SP - 231 EP - 239 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-27584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars T1 - Einsatz thermoanalytischer Methoden bei der Charakterisierung vernetzender Kunststoffe T2 - Anwenderseminar zur Thermoanalyse, Netzsch, Analytica 2012 CY - Munich, Germany DA - 2012-04-18 PY - 2012 AN - OPUS4-25890 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Bohmeyer, W. A1 - Lange, K. T1 - Investigation of the crosslinking behaviour of ehtylene vinyl acetate (EVA) for solar cell encapsulation by rheology and ultrasound N2 - EVA is a widely used material for the encapsulation of photovoltaic modules. It melts at elevated temperatures, and seals the module before it is crosslinked at temperatures above 130 °C by a peroxide-initiated crosslinking reaction. EVA has good optical properties necessary for application in solar modules. For process optimization and quality management, a method for the quick and reliable characterization of EVA crosslinking behaviour is of great value. Here, the practicability of ultrasound for online crosslinking monitoring is demonstrated. A sound velocity increase of about 8 m/s during the crosslinking reaction is found. The ultrasound results are compared with rheometer measurements performed with a curemeter typically used for the investigation of rubber crosslinking. KW - Ethylene vinyl acetate KW - EVA KW - Crosslinking KW - Ultrasound KW - Rheology KW - Curemeter KW - DSC PY - 2012 DO - https://doi.org/10.1016/j.polymertesting.2012.07.004 SN - 0142-9418 VL - 31 IS - 7 SP - 904 EP - 908 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-26291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Characterisation of curing behaviour of carbon fibre epoxy prepreg (CFK, CFC)-analysis of non-cured prepreg and autoclave curing process T2 - 7th International CFK-Valley Stade Convention - Latest Innovations in CFRP Technology CY - Stade, Germany DA - 2013-06-11 PY - 2013 AN - OPUS4-27835 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Trappe, Volker T1 - Modelling of curing behaviour of epoxy resin based on DSC data T2 - 7th International Thermoset Conference CY - Iserlohn, Germany DA - 2013-04-17 PY - 2013 AN - OPUS4-27838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Mc Hugh, Jarlath A1 - Döring, Joachim A1 - Erhard, Anton A1 - Stark, Wolfgang A1 - Raab, S. T1 - Einfluss hoher Temperaturen und Drücke auf die Ultraschalleigenschaften eines Komposit-Prüfkopfes T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2004 CY - Salzburg, Österreich DA - 2004-05-17 PY - 2004 UR - http://www.ndt.net/article/dgzfp04/papers/p12/p12.htm SN - 3-931381-55-2 SP - 1 EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-5214 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Mc Hugh, Jarlath A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Erhard, Anton T1 - Characterisation of epoxy materials used in the development of ultrasound arrays T2 - 16th World Conference on Nondestructive Testing CY - Montreal, Canada DA - 2004-08-30 PY - 2004 UR - http://www.ndt.net/article/wcndt2004/pdf/materials_characterization/616_mchugh.pdf SP - 8 pages PB - International Committee for Non-Destructive Testing CY - Montreal AN - OPUS4-5215 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Hoster, B. A1 - Kürten, Ch. T1 - Nachtemperung von duroplastischen Bauteilen - Spagat zwischen Eigenschaftsverbesserung und Eigenschaftsverschlechterung PY - 2005 SN - 0176-1625 VL - 58 IS - 11 SP - 718 EP - 722 PB - Gupta CY - Ratingen AN - OPUS4-11592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Mc Hugh, Jarlath A1 - Simon, W. T1 - Ultraschall-Prozesskontrolle mechanischer Parameter von aushärtenden Polymeren - Inline-Sensorik für die Herstellung von Kunststoffkomponenten KW - Aushärtung KW - Ultraschall KW - Sensoren KW - Materialparameter PY - 2007 SN - 0025-5300 VL - 49 IS - 5 SP - 238 EP - 242 PB - Hanser CY - München AN - OPUS4-14976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Qualitätskontrolle von Duroplasten unter besonderer Berücksichtigung der Phenoplaste aus heutiger Sicht T2 - Baekeland-Tag 2008 CY - Erkner, Germany DA - 2008-02-22 PY - 2008 AN - OPUS4-16685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Goering, Harald T1 - Charakterisierung der Vernetzungsreaktion von Harnstoff-Formmasse mittels Hochdruck-DSC T2 - 1. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-16720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald T1 - Untersuchungen zum Vernetzungsgrad von Duromeren mittels Methoden der thermischen Analyse T2 - 1. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-16721 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Simulation of cross-linking process of prepregs by dynamic mechanical analysis T2 - 11. Internationale Tagung "Arbeitsgemeinschaft verstärkte Kunststoffe AVK" CY - Essen, Germany DA - 2008-09-22 PY - 2008 AN - OPUS4-17946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Mc Hugh, Jarlath A1 - Trappe, Volker A1 - Schönhals, Andreas T1 - Untersuchungen zum Aushärteverhalten und zum Aushärtungszustand von Epoxidharz T2 - VII Internationale AVK-TV Konferenz CY - Baden-Baden, Germany DA - 2004-09-28 PY - 2004 AN - OPUS4-4759 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fritsch, Sebastian A1 - Stark, Wolfgang A1 - Kelm, Jürgen A1 - Goering, Harald A1 - Krüger, Simone A1 - Opfermann, J. T1 - DMA- und DSC-Untersuchungen zur formalkinetischen Modellierung der Kautschukvulkanisation T2 - Polydays 2004 CY - Potsdam, Germany DA - 2004-10-04 PY - 2004 AN - OPUS4-4760 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Characterisation of Flow and Curing Behaviour of Thermosetting Materials by Thermoanalytical and Ultrasound Methods T2 - 5th International Thermoset Conference Iserlohn CY - Iserlohn, Germany DA - 2008-11-21 PY - 2008 AN - OPUS4-18428 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Straet, T. A1 - Bayerl, H. A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kürten, Ch. T1 - Ultrasonic Measurements on Thermoset Moulding Compounds KW - Ultraschall KW - Fertigungskontrolle KW - Schallgeschwindigkeit KW - Vernetzungsreaktion KW - Qualitätssicherung PY - 2005 SN - 0945-0084 VL - 95 IS - 7 SP - 1 EP - 5 PB - Hanser CY - München AN - OPUS4-10304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Döring, Joachim A1 - Mc Hugh, Jarlath A1 - Kürten, Ch. A1 - Hoster, B. T1 - Online-Aushärtungskontrolle im Werkzeug - Messprinzip und industrielle Anwendungsbeispiele T2 - 9. Internationale AVK (Arbeitsgemeinschaft verstärkte Kunststoffe) Tagung CY - Essen, Germany DA - 2006-09-19 PY - 2006 AN - OPUS4-13039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -