TY - CONF A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Stark, Wolfgang ED - Riedl, A. T1 - Was passiert bei tiefen Temperaturen? - Dichtungsverhalten im Bereich des Glasübergangs N2 - Elastomere werden vielfach als Dichtungsmaterial für verschiedene Anwendungen eingesetzt. In vielen Bereichen ist die Funktion der Dichtung auch bei tiefen Temperaturen erforderlich. Daher ist das Verständnis des Versagensmechanismus von großer Bedeutung. Normalerweise werden Elastomere oberhalb ihres Glass-Gummi Umwandlungsbereiches eingesetzt, wobei die minimale Einsatztemperatur nicht exakt definiert ist. Daher ist es sinnvoll, diese untere Temperatureinsatzgrenze in Abhängigkeit von den Materialeigenschaften zu bestimmen. Hierfür werden die Ergebnisse der thermischen Analyse mit den Resultaten des Druckverformungsrests aus einer abgewandelten Messung mit der Dynamisch Mechanischen Analyse (DMA) kombiniert. Weiterhin werden Ergebnisse von Bauteilversuchen vorgestellt und diskutiert. Die vorgestellten Untersuchungen wurden zum großen Teil auf Untersuchungen im Rahmen der Dissertation von M. Jaunich durchgeführt. T2 - XVIII. Dichtungskolloquium - Sichere und zuverlässige Dichtverbindungen CY - Rheine, Germany DA - 25.09.2013 KW - Dichtung KW - Glasübergang KW - Elastomer KW - Druckverformungsrest PY - 2013 SN - 978-3-8027-2216-5 SP - 51 EP - 58 PB - Vulkan AN - OPUS4-29221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Fritsch, Sebastian A1 - Kelm, Jürgen T1 - Vulcanization Monitoring in the Mould by Means of Ultrasound T2 - German Rubber Conference 2006 CY - Nuremberg, Germany DA - 2006-07-03 KW - Vulkanisation KW - Ultraschall KW - Prozesskontrolle KW - Rheologie PY - 2006 SP - 189 EP - 193 PB - Deutsche Kautschuk-Gesellschaft CY - Frankfurt am Main AN - OPUS4-13082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaal, Mate A1 - Bovtun, Viktor A1 - Stark, Wolfgang A1 - Erhard, Anton A1 - Yakymenko, Y. A1 - Kreutzbruck, Marc T1 - Viscoelastic properties of cellular polypropylene ferroelectrets N2 - Viscoelastic properties of cellular polypropylene ferroelectrets (PP FEs) were studied at low frequencies (0.3–33 Hz) by dynamic mechanical analysis and at high frequencies (250 kHz) by laser Doppler vibrometry. Relaxation behavior of the in-plane Young’s modulus (Y´ 11~1500 MPa at room temperature) was observed and attributed to the viscoelastic response of polypropylene matrix. The out-of-plane Young’s modulus is very small (Y´33≈0.1 MPa) at low frequencies, frequency- and stress-dependent, evidencing nonlinear viscoelastic response of PP FEs. The highfrequency mechanical response of PP FEs is shown to be linear viscoelastic with Y´33≈0.8 MPa. It is described by thickness vibration mode and modeled as a damped harmonic oscillator with one degree of freedom. Frequency dependence of Y*33 in the large dynamic strain regime is described by the broad Cole-Cole relaxation with a mean frequency in kHz range attributed to the Dynamics of the air flow between partially closed air-filled voids in PP FEs. Switching-off the relaxation contribution causes dynamic crossover from the nonlinear viscoelastic regime at low frequencies to the linear viscoelastic regime at high frequencies. In the small strain regime, contribution of the air flow seems to be insignificant and the power-law response, attributed to the mechanics of polypropylene cell walls and closed air voids, dominates in a broad frequency range. Mechanical Relaxation caused by the air flow mechanism takes place in the sound and ultrasound frequency range (10 Hz–1MHz) and, therefore, should be taken into account in ultrasonic applications of the PP FEs deal with strong exciting or receiving signals. KW - Viscoelastic KW - Cellular polypropylene KW - Ferroelectret PY - 2016 U6 - https://doi.org/10.1063/1.4944798 SN - 0021-8979 SN - 1089-7550 SN - 1520-8850 VL - 119 SP - Article Number: 125101 PB - AIP Publishing AN - OPUS4-35956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kürten, C. T1 - Vernetzung reaktiver Kunststoffe mit Ultraschall überwachen KW - Elastomer KW - Epoxidharz KW - Phenolharz KW - Vernetzung KW - Vulkanisation KW - Schallgeschwindgkeit KW - Prozesskontrolle PY - 2008 SN - 0939-2629 SN - 0176-6058 IS - 2 SP - 31 EP - 33 PB - Holzverl. CY - Kissing AN - OPUS4-17587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Walentowski, Heinz-Ulrich T1 - Vernetzen statt Verglasen PY - 2000 UR - http://www.kunststoffe.de/ku/default.asp SN - 0023-5563 VL - 90 IS - 4 SP - 90 EP - 92 PB - Hanser CY - München AN - OPUS4-823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Fengler, Petra A1 - Mc Hugh, Jarlath A1 - Kelm, Jürgen T1 - Verfolgung der Aushärtung bei Epoxidharzen mit der Dynamisch Mechanischen Analyse (DMA) von flüssig bis fest T2 - DMA 242 - Anwender-Treffen CY - Selb, Germany DA - 2004-11-24 PY - 2004 AN - OPUS4-4872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Kürten, C. T1 - Verarbeitung von Harnstoff-Formmassen - Begleitende Online-Prozesskontrolle N2 - Harnstoff-Formmassen gehören zu den duroplastischen Formmassen, die im Werkzeug chemisch vernetzen und so ihre herausragende Temperaturbeständigkeit erreichen. Im Wettbewerb mit Thermoplasten weisen Formmassen den Nachteil auf, dass die Vernetzungsreaktion eine kritische Zeit bedingt, damit die Glasübergangstemperatur soweit verschoben werden kann, dass die heißen Teile stabil und blasenfrei entformt werden können. Die Zykluszeiten sind bei Formmassen daher deutlich höher als bei Thermoplasten. Eine Möglichkeit, die Zykluszeit zu verringern, wäre die Erhöhung der Werkzeugtemperatur, da bekanntlich eine Erhöhung der Reaktionstemperatur um 10 K zu einer Verdoppelung der Reaktionsgeschwindigkeit führt. Allerdings wird dabei das Zeitfenster für die Entformung optimal gehärteter Teile deutlich kleiner, der Prozess anfälliger gegen Schwankungen im Prozess und in der Formmasse-Zusammensetzung. Mit einer Online-Kontrolle des Vernetzungszustands sollte es aber gelingen, den Prozess auch bei einer höheren Werkzeugtemperatur noch stabil zu beherrschen. In der vorliegenden Arbeit wird die Methode der dielektrischen Prozesskontrolle in der Fertigung von Spritzgieß-Formteilen erprobt und die Möglichkeiten einer Prozesssteuerung werden herausgearbeitet. KW - Harnstoffharz KW - Elektroinstallationsteile KW - Aushärtungsverlauf KW - Kochversuch PY - 2008 SN - 0176-1625 VL - 61 IS - 12 SP - 790 EP - 793 PB - Gupta CY - Ratingen AN - OPUS4-18734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Döring, Joachim A1 - Stark, Wolfgang T1 - Untersuchungen zur Aushärtung von Duroplasten T2 - DACH-Tagung 1996 CY - Lindau, Deutschland DA - 1996-05-13 PY - 1996 SN - 3-931381-07-0 VL - 52 SP - 765 EP - 771 AN - OPUS4-22935 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald T1 - Untersuchungen zum Vernetzungsgrad von Duromeren mittels Methoden der thermischen Analyse T2 - 1. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-16721 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Mc Hugh, Jarlath A1 - Trappe, Volker A1 - Schönhals, Andreas T1 - Untersuchungen zum Aushärteverhalten und zum Aushärtungszustand von Epoxidharz T2 - VII Internationale AVK-TV Konferenz CY - Baden-Baden, Germany DA - 2004-09-28 PY - 2004 AN - OPUS4-4759 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mielke, Werner A1 - Stark, Wolfgang T1 - Unter Kontrolle - Aushärtung duroplastischer Formmassen PY - 1995 SN - 0047-3766 VL - 29 SP - 35 EP - 37 PB - Verl. Moderne Industrie CY - Landsberg AN - OPUS4-11798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Döring, Joachim A1 - Mc Hugh, Jarlath A1 - Goering, Harald A1 - Kürten, Ch. A1 - Bräuning, R. A1 - Götz, J. T1 - Ungesättigte Polyesterharze, BMC und SMC - Charakterisierung von Reifung bis Aushärtung T2 - 8. Internationale Tagung der Arbeitsgemeinschaft Verstärkte Kunststoffe - Technische Vereinigung e. V. (AVK-TV) CY - Baden-Baden, Germany DA - 2005-09-27 PY - 2005 AN - OPUS4-14333 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - von der Ehe, Kerstin A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Stark, Wolfgang T1 - Understanding the low temperature properties of rubber seals N2 - Rubbers are widely used as main sealing materials for containers for low and intermediate level radioactive waste and as additional component to metal seals in spent fuel and high active waste containers. The save encapsulation of the radioactive container inventory has to be guaranteed according to legislation and appropriate guidelines for long term storage periods as well as down to temperatures of -40 °C during transport. Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of rubbers are strongly temperature dependent. At low temperatures this is caused by the rubber-glass transition (abbr. glass transition). During continuous cooling the material changes from rubber-like entropy-elastic to stiff energy-elastic behaviour, that allows nearly no strain or retraction, due to the glass transition. Hence rubbers are normally used above their glass transition but the minimum working temperature limit is not defined precisely, what can cause problems during application. Therefore the lower operation temperature limit of rubber seals should be determined in dependence of the material properties. The results of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) are combined with the results of standardized measurements as the compression set according to ISO 815. To reduce the test time of the standard tests a faster technique was developed. Additionally, the breakdown temperature of the sealing function of complete O-ring seals is measured in a component test setup to compare it with the results of the other tests. The experimental setup is capable of measuring the leakage rate at low temperatures by the pressure rise method. A fluorocarbon rubber (FKM) was selected for this investigation as it is often used for radioactive waste containers. Some materials (seals and test sheets) were purchased from a commercial seal producer and some materials were compounded and cured at BAM in form of rubber sheets. T2 - PATRAM 2010 - 16th International symposium on the packaging and transport of radioactive materials CY - London, UK DA - 2010-10-03 KW - Dichtungen KW - Elastomere KW - Tieftemperaturverhalten PY - 2010 SP - 1 EP - 7 (Session T41 / Paper 169) AN - OPUS4-23887 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - von der Ehe, Kerstin A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Stark, Wolfgang T1 - Understanding low temperature properties of elastomer seals N2 - Elastomers are widely used as the main sealing materials for containers for low and intermediate level radioactive waste and as an additional component to metal seals in spent fuel and high active waste containers. The safe encapsulation of the radioactive container inventory has to be guaranteed according to regulation and appropriate guidelines for long term storage periods as well as for temperatures as low as -40°C during transport. Therefore, the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of elastomers are strongly temperature dependent. At low temperatures, this is caused by the rubber-glass transition (abbreviated: glass transition). During continuous cooling, the material changes from a rubber-like entropy elastic to a stiff energy elastic behaviour, which allows nearly no strain or retraction. Hence, rubbers are normally used above their glass transition, but the minimum working temperature limit is not defined precisely; this can cause problems during the above noted applications. Therefore, the lower operation temperature limit of elastomer seals must be determined in dependence of the material properties. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) are combined with standardised measurements to determine the compression set according to ISO 815. To reduce the test time of the standard tests, a faster technique than normally used was developed. Additionally, the breakdown temperature of the sealing function of complete O ring seals was measured in a component test set-up to compare it with the results of the other tests. The experimental set-up is capable of measuring the leakage rate at low temperatures by the pressure rise method. A fluorocarbon rubber (FKM) was selected for this investigation as it is often used for radioactive waste containers. The materials (seals and test sheets) were purchased from a commercial seal producer. KW - Sealing material KW - Elastomer KW - Compression set KW - Dynamic mechanical analysis KW - Low temperature behaviour PY - 2011 U6 - https://doi.org/10.1179/1746510911Y.0000000004 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 2 SP - 83 EP - 88 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-24015 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Mc Hugh, Jarlath A1 - Bartusch, Jürgen T1 - Ultrasound on-line cure monitoring for industrial applications N2 - In recent years eure monitoring with ultrasonic methods became more important. An on-line measurement System for industrial applications is presented in this paper. It operates in through-transmission and the measured parameters are the sound velocity and the attenuation of the sound wave. An objective of this paper is to establish the ränge of possible applications for an ultrasonic eure monitoring System. KW - Ultrasonic monitoring KW - Cure process KW - Composite material KW - Process controlling PY - 2000 SN - 0963-6935 PB - Woodhead Publ. CY - Cambridge AN - OPUS4-1061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Ultrasound measuring system for flow front and cure monitoring at composite manufacturing (RTM, prepreg, injection moulding) T2 - Composite Europe, 5. Europäische Fachmesse und Forum für Verbundstoffe, Technologie und Anwendungen CY - Essen, Germany DA - 2010-09-14 PY - 2010 AN - OPUS4-22102 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang T1 - Ultrasonic Production Control N2 - Ultrasound waves penetrate solid objects without damaging them. Their fields of application range from the imaging of internal organs in medicine, to interior testing of mechanical and chemical engineering components. However, ultrasonic systems can also be used to visualise the way the mechanical properties of reactive resins change during processing in the mould. PY - 2001 SN - 0945-0084 VL - 91 IS - 1 SP - 35 EP - 36 PB - Hanser CY - München AN - OPUS4-2135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Straet, T. A1 - Bayerl, H. A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kürten, Ch. T1 - Ultrasonic Measurements on Thermoset Moulding Compounds KW - Ultraschall KW - Fertigungskontrolle KW - Schallgeschwindigkeit KW - Vernetzungsreaktion KW - Qualitätssicherung PY - 2005 SN - 0945-0084 VL - 95 IS - 7 SP - 1 EP - 5 PB - Hanser CY - München AN - OPUS4-10304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Mc Hugh, Jarlath A1 - Kürten, Ch. A1 - Hoster, B. A1 - Bohmeyer, W. A1 - Lange, K. T1 - Ultraschallmesstechnik zur Wareneingangskontrolle und zur Überwachung T2 - 5th Int. Thermoset Conference CY - Iserlohn, Germany DA - 2008-11-20 PY - 2008 AN - OPUS4-18468 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Mc Hugh, Jarlath A1 - Simon, W. T1 - Ultraschall-Prozesskontrolle mechanischer Parameter von aushärtenden Polymeren - Inline-Sensorik für die Herstellung von Kunststoffkomponenten KW - Aushärtung KW - Ultraschall KW - Sensoren KW - Materialparameter PY - 2007 SN - 0025-5300 VL - 49 IS - 5 SP - 238 EP - 242 PB - Hanser CY - München AN - OPUS4-14976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen T1 - Ultraschall on-line Prozesskontrolle bei der Vulkanisation KW - Prozesskontrolle KW - Vulkanisation KW - Ultraschall KW - Sensoren KW - Schubmodul KW - Verlustmodul PY - 2000 SN - 0948-3276 SN - 0022-9520 SP - 9 Seiten PB - Hüthig CY - Heidelberg AN - OPUS4-997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Stark, Wolfgang T1 - Tieftemperaturverhalten von Elastomerdichtungen - Eigenschaftsbestimmung für den Einsatz in Transport- und Lagerbehältern für radioaktive Stoffe N2 - Die Messung des dynamischen Speichermoduls mit der Dynamisch-Mechanischen-Analyse ermöglicht einen schnellen Überblick über das temperaturabhängige Verhalten von elastomeren Dichtungsmaterialien. Ein direkter Rückschluss von der so ermittelten Glasübergangstemperatur Tg auf die Versagenstemperatur einer Dichtung ist aber ohne zusätzliche Messungen bisher nicht möglich. Mit den Ergebnissen des Druckverformungsrestes DVR und des DVRDMA ist eine ge-nauere Beschreibung der Tieftemperatureigenschaften und dadurch der Funktion von elastomeren Dichtungsmaterialien möglich. Messungen ergeben beispielsweise, dass sich das EPDM bei einer Temperatur von -40 °C laut der Dynamisch Mechanischen Analyse noch im gummielastischen Bereich befindet. Die DVRDMA-Werte zeigen eine Rückstellung um mehr als 40 % der Ausgangsdeformation in wenigen Minuten. Mit derart detailliert bestimmten Eigenschaften lassen sich Rückschlüsse auf einsatzspezifische Anforderungen wie z. B. die Dichtwirkung in Abhängigkeit von Betriebstemperatur und mechanischer Belastungsgeschwindigkeit ziehen, so dass je nach Einsatzbedingungen für die Dichtungen eine geeignete Materialauswahl getrof-fen werden kann. T2 - Jahrestagung Kerntechnik 2010 CY - Berlin, Deutschland DA - 2010-05-04 KW - Dichtungen KW - Elastomere KW - Tieftemperaturverhalten PY - 2010 IS - Sektion 5 / 503 SP - 1 EP - 4 CY - Berlin AN - OPUS4-21272 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Goering, Harald A1 - Stark, Wolfgang A1 - Bayerl, H. A1 - Brinkmann, P. T1 - Thermoanalytische Untersuchungen zur Phenolharzhärtung unter hohem Druck - Ein Weg zur Optimierung der Nachtemperung T2 - 3rd International Thermoset Conference CY - Iserlohn, Deutschland DA - 2005-04-21 KW - Post curing KW - High pressure DSC KW - DMA KW - Reaction kinetic KW - Phenolic resin PY - 2005 SP - 107 EP - 114 PB - Fachhochschule Südwestfalen - Hochschule für Technik und Wirtschaft CY - Iserlohn AN - OPUS4-7452 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Böhning, Martin T1 - Thermoanalytische Methoden DSC/Hochdruck-DSC und DMA bei der Charakterisierung der Vernetzung reaktiver Kunststoffe T2 - Praxistag Uni Rostock "Thermische Analyse für spezielle Anwendungen" CY - Rostock, Germany DA - 2012-06-19 PY - 2012 AN - OPUS4-26084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias T1 - Thermoanalytische Charakterisierung von Ethylen-Vinylacetat-Copolymer (EVA) für Photovoltaikmodule N2 - Das Ziel der Untersuchungen war mit Hilfe von DSC und DMA EVA-Folien im Anlieferungszustand hinsichtlich der Lage der Glasübergangstemperatur, des Schmelzverhaltens und der Temperaturabhängigkeit der Vernetzungsreaktion zu charakterisieren. Auf dieser Basis sollte die Lieferstabilität im Sinne einer Wareneingangskontrolle auf eine messtechnische Basis gestellt werden. In einem 2. Schritt sollte die vernetzte Folie dahingehend charakterisiert werden, ob infolge der Vernetzung eine Änderung der KW - Photovoltaik KW - Klebfolie KW - EVA KW - DSC KW - DMA PY - 2011 VL - 8 SP - 3 EP - 5 AN - OPUS4-24168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, Uwe T1 - Thermoanalyse der Phenolharzhärtung - Ein Weg zur Optimierung der Nachtemperung N2 - Angesichts der spezifischen Bedeutung der Aushärtung von Phenolharzen für ihre Eigenschaften als Ingenieurwerkstoffe besteht großes Interesse an deren quantitativer Charakterisierung. Mittels DSC-Messungen unter hohem Druck (HP-DSC) kann die Vernetzungsreaktion der Phenolharzformmassen durch die Unterdrückung der Verdampfung niedermolekularer Substanzen ohne störende Überlagerungen verfolgt werden. Mittels verschiedener Vernetzungsgrade können die Einflussparameter der Aufheizrate und der Nachtemperung optimiert werden. Die Messergebnisse ermöglichen eine Modellierung der Reaktionskinetik mit dem Ziel einer verbesserten Prozessführung und Qualitätskontrolle in der industriellen Praxis. KW - Phenolharze KW - Thermische Analyse KW - DMA KW - DSC KW - Aushärtung KW - Glasübergang PY - 2006 SN - 0025-5300 VL - 48 IS - 11-12 SP - 556 EP - 561 PB - Carl Hanser Verlag CY - München AN - OPUS4-13802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Goering, Harald A1 - Stark, Wolfgang A1 - Bayerl, H. A1 - Brinkmann, P. T1 - Thermo Analytical Investigations of Phenol Moulding Compound Curing - Potential for Post-Cure Optimisation T2 - 3rd International Thermoset Conference CY - Iserlohn, Germany DA - 2005-04-21 KW - Post curing KW - High pressure DSC KW - DMA KW - Reaction kinetic KW - Phenolic resin PY - 2005 SP - 219 EP - 225 PB - Fachhochschule Südwestfalen - Hochschule für Technik und Wirtschaft CY - Iserlohn AN - OPUS4-7453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gorokhovatsky, Y.A. A1 - Krüger, Simone A1 - Brademann-Jock, Kerstin A1 - Stark, Wolfgang A1 - Temnov, Dmitri A1 - Kuvshinova, Oksana A1 - Goldade, V.A. ED - Fleming, R. J. T1 - Thermally stimulated luminescence in LDPE fibers T2 - 11th International Symposium on Electrets (ISE 11) CY - Melbourne, Australia DA - 2002-10-01 PY - 2002 SN - 0-7803-7560-2 SP - 138 EP - 140 PB - IEEE Service Center CY - Piscataway, NJ AN - OPUS4-1654 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Goering, Harald A1 - Mc Hugh, Jarlath A1 - Opfermann, J. A1 - Knappe, S. T1 - The RTM-Process and the Problems with Gelation, Vitrification and Degree of Curing T2 - 6th Internationale AVK-Tv Conference CY - Baden-Baden, Germany DA - 2003-09-07 PY - 2003 AN - OPUS4-4072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Sturm, Heinz A1 - Schulz, Eckhard A1 - Stark, Wolfgang A1 - Bovtun, V. A1 - Friedrich, Jörg Florian ED - Olefjord, I. ED - Nyborg, L. ED - Briggs, D. T1 - Techniques for surface composition analysis with scanning force microscopy (SFM) using electrical surface properties T2 - 7th European Conference on Applications of Surface and Interface Analysis CY - Göteborg, Sweden DA - 1997-06-16 PY - 1997 SN - 0-471-97827-2 SP - 579 EP - 582 PB - Wiley CY - Chichester AN - OPUS4-6854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Simulation of cross-linking process of prepregs by dynamic mechanical analysis T2 - 11. Internationale Tagung "Arbeitsgemeinschaft verstärkte Kunststoffe AVK" CY - Essen, Germany DA - 2008-09-22 PY - 2008 AN - OPUS4-17946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stark, Wolfgang A1 - Döring, Joachim A1 - Kelm, Jürgen A1 - Fritsch, Sebastian ED - Green, R. E. ED - Djordjevic, B. B. ED - Hentschel, M. P. T1 - Rubber processing monitored by ultrasound T2 - 11th International Symposium on Nondestructive Characterization of Materials CY - Berlin, Germany DA - 2002-06-24 PY - 2003 SN - 3-540-40154-7 SP - 659 EP - 664 PB - Springer CY - Berlin AN - OPUS4-2769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Mc Hugh, Jarlath A1 - Bartusch, Jürgen A1 - Fengler, Petra T1 - Rheologische und akustische Bestimmung der Fließ-Härtungseigenschaften von Injektionsharzen N2 - Zusammenfassung Der Ausgangspunkt für diese Arbeiten ist eine in [1] beschriebene Ultraschall-(US)-Sensorik zur Aushärtungskontrolle. Sie wurde für rieselfähige Formmassen entwickelt [2,3]. Darauf aufbauend ist es das Ziel der vorliegenden Arbeit, die Voraussetzungen für den Einsatz dieser Sensorik beim Harzinjektionsverfahren zu schaffen und ihre Kalibrierung durch rheologische und DSC-Messungen zu ermöglichen. Der erste Teil des Beitrages beschäftigt sich mit dem technologischen Ablauf des Harzinjektionsverfahren und den Einsatzmöglichkeiten der US-Sensorik bei dieser Technologie. Ergebnisse von Schallgeschwindigkeits- und Dämpfungsmessungen für EP-Harze werden vorgestellt. Im zweiten Teil wird auf das Kalibrieren der US-Sensorik für den Verarbeiter eingegangen. Es kann mittels der bisherigen Prozessführung oder durch Vergleich mit den Ergebnissen anderer Mess-Verfahren wie Rheometer- oder Differential-Scanning-Calerometry-(DSC)-Messungen erfolgen. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Ultraschall KW - Harzinjektionsverfahren KW - RTM KW - Prozesskontrolle KW - Aushärtung PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/v51/v51.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-1913 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mc Hugh, Jarlath A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Guey, J. L. T1 - Relationship between the Mechanical and Ultrasound Properties of Polymer Materials T2 - 9th European Conference on NDT CY - Berlin, Germany DA - 2006-09-25 KW - Ultrasound KW - DMA KW - Epoxy KW - Modulus KW - tan delta KW - High temperature PY - 2006 SN - 3-931381-86-2 SP - 1(?) EP - 9(?) PB - European Federation for Non-Destructive Testing CY - Berlin AN - OPUS4-14065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frübing, P. A1 - Wang, F. A1 - Günter, C. A1 - Gerhard, R. A1 - Wegener, M. A1 - Jaunich, Matthias A1 - Stark, Wolfgang T1 - Relation between dielectric and mechanical losses in ferroelectric poly(vinylidene fluoride - hexafluoropropylene) films N2 - The temperature dependences of dielectric permittivity and elastic modulus of poly(vinylidene fluoride - hexafluoropropylene) (P(VDF-HFP)) are compared and explained by use of structural data obtained by differential scanning calorimetry and X-ray analysis. Special emphasis is put on the effect of uniaxial stretching which renders the polymer ferroelectric. It is shown that dielectric and mechanical relaxations at the glass transition (aa relaxation) are closely related and not significantly affected by stretching. It is further confirmed that stretching destroys the non-polar spherulitic crystalline structure and produces relatively small-sized polar crystallites. This manifests in the disappearence of the so-called ac relaxation which is associated to molecular motions within the spherulitic crystalline lamellae. However, there are discrepancies between dielectric and mechanical losses above the glass transition which point towards a still not described structural transition. T2 - 10th IEEE International conference on solid dielectrics (ICSD) CY - Potsdam, Germany DA - 2010-07-04 KW - Poly(vinylidene(fluoride - hexafluoropropylene) KW - P(VDF-HFP) KW - Ferroelectric polymer KW - Dielectric relaxation KW - Dynamic mechanical analysis KW - Uniaxial stretching PY - 2010 SN - 978-1-4244-7945-0 U6 - https://doi.org/10.1109/ICSD.2010.5567936 SP - 1 EP - 4(?) AN - OPUS4-23421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Qualitätskontrolle von Duroplasten unter besonderer Berücksichtigung der Phenoplaste aus heutiger Sicht T2 - Baekeland-Tag 2008 CY - Erkner, Germany DA - 2008-02-22 PY - 2008 AN - OPUS4-16685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Kürten, Ch. T1 - Prozessüberwachung bei duroplastischen Formmassen N2 - Dielektrische Sensoren überwachen den Vernetzungsprozess beim Spritzgießen direkt im Werkzeug. Der Aushärtungszustand wird kontinuierlich verfolgt, Abweichungen werden erkannt und die Zykluszeit optimiert. KW - Prozesskontrolle KW - Aushärtegrad KW - Kochversuch KW - Harnstoffformasse KW - Dielektrik PY - 2006 SN - 0023-5563 IS - 7 SP - 97 EP - 100 PB - Hanser CY - München AN - OPUS4-13084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Properties of elastomeric seals at low temperature T2 - International rubber conference (IRC 2009) CY - Nürnberg, Germany DA - 2009-06-29 PY - 2009 IS - Poster 23 SP - 1 EP - 3 AN - OPUS4-19611 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang T1 - Produktionskontrolle mit Ultraschall N2 - Ultraschallwellen durchdringen Festkörper, ohne sie zu schädigen. Der Einsatzbereich von Ultraschall reicht von der Darstellung der inneren Organe in der Medizin bis zur Prüfung des Inneren von Bauteilen im Maschinen- und Anlagenbau. Ultraschall-Systeme können jedoch auch genutzt werden, um sichtbar zu machen, wie sich mechanische Eigenschaften von Reaktionsharzen während ihrer Verarbeitung im Werkzeug verändern. PY - 2001 UR - http://www.kunststoffe.de/directlink.asp?KU101838 SN - 0023-5563 VL - 91 IS - 1 SP - 83 EP - 85 PB - Hanser CY - München AN - OPUS4-2137 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Bayerl, H. A1 - Hoster, B. T1 - Post-annealing of thermosets T2 - 4th International Thermoset Conference CY - Iserlohn, Germany DA - 2006-11-16 PY - 2006 AN - OPUS4-13801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, Uwe A1 - Krüger, Simone A1 - Bayerl, H. A1 - Kürten, Ch. T1 - Optimierung der Nachtemperung von Formteilen mit Hilfe von Thermo- und dynamisch mechanischer Analyse T2 - 8. Internationale Tagung der Arbeitsgemeinschaft Verstärkte Kunststoffe - Technische Vereinigung e. V. (AVK-TV) CY - Baden-Baden, Germany DA - 2005-09-27 PY - 2005 AN - OPUS4-10989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Fengler, Petra A1 - Michel, Uwe T1 - Optimierung der Nachtemperung von Formteilen für den Einsatz am heißen Motor mit Hilfe der Dynamisch Mechanischen Analyse T2 - 9. Anwendertreffen Dynamisch Mechanische Analyse CY - Selb, Germany DA - 2006-02-14 PY - 2006 AN - OPUS4-12113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Döring, Joachim A1 - Mc Hugh, Jarlath A1 - Kürten, Ch. A1 - Hoster, B. T1 - Online-Aushärtungskontrolle im Werkzeug - Messprinzip und industrielle Anwendungsbeispiele T2 - 9. Internationale AVK (Arbeitsgemeinschaft verstärkte Kunststoffe) Tagung CY - Essen, Germany DA - 2006-09-19 PY - 2006 AN - OPUS4-13039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Mc Hugh, Jarlath A1 - Straet, T. A1 - Bayerl, H. A1 - Kürten, Ch. T1 - Online Überwachung des Spritzgießprozesses mit Hilfe von Ultraschall T2 - 8. Internationale Tagung der Arbeitsgemeinschaft Verstärkte Kunststoffe-Technische Vereinigung e. V. (AVK-TV) CY - Baden-Baden, Germany DA - 2005-09-27 PY - 2005 AN - OPUS4-11622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Goering, Harald A1 - Michel, U. A1 - Bayerl, H. T1 - Online monitoring of thermoset post-curing by dynamic mechanical thermal analysis DMTA N2 - Thermosetting moulding compounds are synthetic materials which can be easily formed in the molten state and achieve high temperature stability due to a cross-linking process which takes place during manufacture. To ensure thermal and mechanical properties, post-curing of moulded phenolic resin components is necessary for high quality applications. In the industrial practice, post-curing time-temperature-programs are heuristically acquired. In this paper, dynamical mechanical thermal analysis is employed to determine optimal post-curing conditions for injection moulded parts from phenolic resin. KW - DMTA KW - Moulding compound KW - Thermoset KW - Phenolic resin KW - Post-curing PY - 2009 U6 - https://doi.org/10.1016/j.polymertesting.2009.02.005 SN - 0142-9418 VL - 28 IS - 6 SP - 561 EP - 566 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-19822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Fritsch, Sebastian A1 - Döring, Joachim A1 - Kelm, Jürgen A1 - Mc Hugh, Jarlath T1 - Online Kontrolle der Vernetzungsreaktion von Kunststoffen mit Ultraschall T2 - Werkstoffwoche 2004: Kongress für innovative Werkstoffe, Verfahren und Anwendungen CY - Munich, Germany DA - 2004-09-21 PY - 2004 AN - OPUS4-4874 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Stark, Wolfgang A1 - Bohmeyer, W. ED - Karbhari, V.M. T1 - Non-destructive evaluation (NDE) of composites: using ultrasound to monitor the curing of composites N2 - Typical composite materials for lightweight construction consist of a fibre (glass or carbon) reinforced thermosetting matrix. The impregnation of the fabric is made with liquid resin – usually epoxy resin or unsaturated polyester resin are used. The main processing methods are resin transfer moulding (RTM) and prepreg technology often used in combination with autoclave curing. After shaping, the resin must be cured. The final properties of the produced parts depend on the curing degree and the final glass transition temperature. Analytical methods and the use of ultrasound for online cure monitoring in the manufacturing process are introduced. Examples for the application of ultrasonic cure monitoring for the production of composite parts for traffic systems are also covered. KW - Epoxy KW - DSC KW - DMA KW - Kinetic KW - Autoclave KW - Curing KW - Glass transition KW - Curing behaviour KW - Curing degree KW - Rheology KW - Differential scanning calorimetry KW - Dynamic mechanical analysis KW - Sound velocity KW - Sound damping KW - Resin transfer moulding KW - RTM KW - Prepreg PY - 2013 SN - 978-0-85709-344-8 SN - 978-0-85709-355-4 U6 - https://doi.org/10.1533/9780857093554.1.136 SN - 2052-5281 SN - 2052-529X N1 - Serientitel: Woodhead publishing sereies in composites science and engineering – Series title: Woodhead publishing sereies in composites science and engineering VL - 43 IS - Part 1 / Chapter 7 SP - 136 EP - 181 PB - Woodhead Publishing Ltd CY - Cambridge, UK AN - OPUS4-28848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Hoster, B. A1 - Kürten, Ch. T1 - Nachtemperung von duroplastischen Bauteilen - Spagat zwischen Eigenschaftsverbesserung und Eigenschaftsverschlechterung PY - 2005 SN - 0176-1625 VL - 58 IS - 11 SP - 718 EP - 722 PB - Gupta CY - Ratingen AN - OPUS4-11592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Fritsch, Sebastian A1 - Stark, Wolfgang A1 - Kelm, Jürgen ED - Kühnert, I. T1 - Möglichkeiten der Online-Kontrolle der Vulkanisation mit Ultraschall T2 - 18. TECHNOMER 2003 ; 18. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 2003-11-13 KW - Kautschuk KW - Vulkanisation KW - Ultraschall PY - 2003 SN - 3-00-012510-8 SP - 1 EP - 10 PB - Techn. Univ. CY - Chemnitz AN - OPUS4-2822 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - Stark, Wolfgang T1 - Monitoring the vulcanization of rubber with ultrasound: Influence of material thickness and temperature N2 - In consideration of the influence of the curing reaction on the material properties of elastomers, it is very important to control the vulcanization process properly. As shown previously [1], the effects of the vulcanization reaction of an elastomer can be monitored by use of ultrasonic sound waves. This technique has to a certain degree a high similarity to the standard curemeter test according to ISO 6502 but can be applied also inside a production tool. So far, the method was only applied to the vulcanization of one compound at a given temperature and sample thickness. This is now complemented with measurements on another compound system at different temperatures and sample thicknesses. The expected effects of temperature and thickness on the curing behaviour were found by use of the ultrasound online control. KW - Vulcanization KW - Cure process KW - Ultrasound KW - Curemeter KW - Elastomer KW - Natural rubber PY - 2009 U6 - https://doi.org/10.1016/j.polymertesting.2009.08.006 SN - 0142-9418 VL - 28 IS - 8 SP - 901 EP - 906 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-19959 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -