TY - CONF A1 - Klinge, Andrea A1 - Mönig, Julian A1 - Kalbe, Ute A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Ziegert, Christof A1 - Röhlen, Ulrich A1 - Roswag-Klinge, Eike T1 - upMIN 100 – upcycling MINeralischer Bau- und Abbruchabfälle zur Substitution natürlicher Gesteinskörnungen in Lehmbaustoffen T1 - upMIN 100 – Upcycling mineral construction and demolition debris as a substitute for natural aggregates in earth building materials N2 - Um zukünftig die Entnahme von Primärrohstoffen und die Deponierung von geeignetem Bodenaushub zu vermeiden, wurde im Forschungsvorhaben «upMIN100» der Einsatz von rezyklierten Gesteinskörnungen < 2 mm in Lehmbaustoffen untersucht. Diese Korngrößen aus Rezyklaten, die je nach Ausgangsstoffen und Produkt 5 – 70 % des fertigen Baustoffs ausmachen, waren zum Zeitpunkt des Projektstarts in den gültigen Lehmbaustoff-Normen DIN 18945 – 18948 nicht zugelassen, da diese als Zusatzstoffe nur natürliche Gesteinskörnungen nach DIN EN 12620, Mehl aus mörtelfreien Ziegeln sowie Blähperlit etc. nach DIN EN 13055-1 und als Bindemittel nur Baulehm aus natürlichen Vorkommen vorsahen. Um den Einsatz von rezyklierten Bau- und Abbruchabfällen für Lehmbaustoffe in der Norm zu ermöglichen, mussten daher die technische Durchführbarkeit, Qualitätsanforderungen an Ausgangsstoffe (z.B. Schadstoffgrenzwerte in Bezug auf Gesundheits- und Umweltverträglichkeit) sowie zulässige Anteile der Rezyklate geregelt werden. Aktuelle Sortier- und Aufbereitungsmethoden wurden im Hinblick auf die technische sowie die wirtschaftliche Machbarkeit überprüft und auf eine mögliche Optimierung untersucht. Um Fragen zur technischen Machbarkeit beantworten zu können, wurde im Vorhaben die exemplarische Entwicklung von zwei wiederverwendbaren Lehmbaustoffen (Lehmstein, Lehmputzmörtel) angestrebt, um zukünftig sowohl das Abfallaufkommen als auch die Rohstoffinanspruchnahme zu reduzieren. Zum einen sollten die Zuschläge bis zu 100% aber auch das natürliche Bindemittel Ton zu 80% – 100% substituiert werden. Der Machbarkeitsnachweis für beide Entwicklungen wurde in Form eines Prototyps mit einem Technologie-Reifegrad 4–5 (TRL 4–5) erbracht. N2 - To avoid the extraction of primary raw materials and the landfilling of suitable excavated soil in the future, the use of recycled aggregates < 2 mm in earth building materials was investigated in the “upMIN 100” research project. These grain sizes from recycled materials, which make up 5–70 % of the finished building material depending on the source materials and product, were not permitted in the applicable earth building material standards DIN 18945–18948 at the time the project started, as these only allow natural aggregates in accordance with DIN EN 12620, flour from mortarfree bricks and expanded perlite etc. as additives in accordance with DIN EN 13055-1 and only building clay from natural sources as a binder. For the use of recycled construction and demolition waste for earth building materials in the standard, the technical feasibility, quality requirements for source (e. g. limit values for harmful substances in terms of health and environmental compatibility) and permissible proportions of recyclates had to be regulated. Current sorting and processing methods were reviewed in terms of technical and economic feasibility and examined for possible optimisation. To ascertain the technical feasibility of the use of recycled construction demolition waste for earth building materials, the project developed two reusable earth building materials (earth blocks, clay plaster mortar) as examples of both waste reduction and of the use of raw materials in the future. On the one hand, up to 100 % of the aggregates and 80–100 % of the natural binder clay should be substituted. The proof of concept for both developments was provided in the form of a prototype with a technology readiness level 4–5 (TRL 4–5). T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Recycled aggregates KW - Earthen building materials KW - Contaminants KW - Reuse KW - Resources PY - 2024 SP - 1 EP - 10 CY - Weimar AN - OPUS4-62612 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Musyanovych, A. A1 - Grimmer, Christoph A1 - Sadak, A. E. A1 - Heßling, L. A1 - Lüdicke, M. A1 - Bilsel, M. A1 - Horn, Wolfgang A1 - Richter, Matthias T1 - Polymer Capsules with Volatile Organic Compounds as Reference Materials for Controlled Emission N2 - Encapsulation of volatile organic compounds (VOCs) that could evaporate at a defined rate is of immense interest for application in emission reference materials (ERMs). Polyurethane/polyurea microcapsules with various VOC active ingredients (limonene, pinene, and toluene) were successfully produced by interfacial polymerization with Shirasu porous glass membrane emulsification in a size range between 10 and 50 μm. The effect of surfactant, VOC, monomer(s) type, and ratio has a great effect on the formulation process and morphology of capsules. The type of VOC played a significant role in the encapsulation efficiency. Due to the difference in vapor pressure and VOC/water interfacial tension, the formulation for encapsulation was optimized for each individual VOC. Furthermore, to achieve effective stability of the large droplets/capsules, a combination of ionic and nonionic surfactants was used. Optical and scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA), were used to characterize the optimized microcapsules. The results showed that the obtained microcapsules exhibited a spherical shape and core–shell morphology and featured characteristic urethane-urea bonds. The amount of encapsulated VOC ranges between 54 and 7 wt %. The emission tests were performed with the help of the emission test chamber procedure (EN 16516). The limonene-loaded polyurethane/polyurea microcapsules show a change in emission rate of less than 10% within 14 days and can be considered as a potential candidate for use as an ERM. KW - Polymer microcapsules KW - Membrane emulsification KW - Polyaddition KW - Volatile organic compound (VOC) KW - Emission testing PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-619227 DO - https://doi.org/10.1021/acsami.4c12826 SN - 1944-8252 VL - 16 IS - 50 SP - 69999 EP - 70009 PB - ACS AN - OPUS4-61922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - de Krom, I. A1 - Heikens, D. A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Richter, Matthias A1 - Baldan, A. T1 - Metrological generation of SI-traceable gas-phase standards and reference materials for (semi-) volatile organic compounds N2 - EN 16516 sets specifications for the determination of emissions into indoor air from construction products. Reliable, accurate and International System of Unit (SI)-traceable measurement results of the emissions are the key to consumer protection. Such measurement results can be obtained by using metrologically traceable reference materials. Gas-phase standards of volatile organic compounds (VOCs) in air can be prepared by a variety of dynamic methods according to the ISO 6145 series. However, these methods are not always applicable for semi-VOCs (SVOCs) due to their high boiling point and low vapour pressure. Therefore, a novel dynamic gas mixture generation system has been developed. With this system gas-phase standards with trace level VOCs and SVOCs in air can be prepared between 10 nmol mol−1 and 1000 nmol mol−1. The VOCs and SVOCs in this study have normal boiling points ranging from 146 °C to 343 °C. Metrologically traceable reference materials of the gas-phase standard were obtained by sampling of the VOC gas-phase standard into Tenax TA® sorbent material in SilcoNert® coated stainless steel tubes. Accurately known masses between 10 ng and 1000 ng per VOC were sampled. These reference materials were used to validate the dynamic system. Furthermore, the storage and stability periods of the VOCs in the reference materials were determined as these are crucial characteristics to obtain accurate and SI-traceable reference materials. In a round robin test (RRT), the reference materials were used with the aim of demonstrating the feasibility of providing SI-traceable standard reference values for SVOCs for interlaboratory comparison purposes. Based on the results from the validation, the storage and stability studies and the RRT, gas-phase standards and reference materials of VOCs and SVOCs with relative expanded uncertainties between 5% and 12% (k = 2) have been developed. These reference standards can be used as calibrants, reference materials or quality control materials for the analysis of VOC emissions. KW - SVOC KW - Dynamic calibration gas mixtures KW - Reference materials KW - Indoor air KW - Thermal desorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-565978 DO - https://doi.org/10.1088/1361-6501/aca704 VL - 34 IS - 3 SP - 1 EP - 13 PB - IOP Publishing AN - OPUS4-56597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Klinke, A. A1 - Horn, Wolfgang A1 - Kalbe, Ute A1 - Mönig, J. A1 - Richter, Matthias A1 - Roswag-Klinge, E. A1 - Röhlen, U. A1 - Ziegert, C. T1 - Upcycling mineralischer Bau- und Abbruchabfälle (upMIN 100) N2 - Der Bausektor ist einer der ressourcenintensivsten Sektoren in Deutschland und ist für 40 % der CO2-Emissionen verantwortlich. Für den Bau von Gebäuden werden in Deutschland jährlich rund 517 Millionen Tonnen mineralische Rohstoffe benötigt. Gleichzeitig stellen mineralische Bauabfälle mit 229,3 Millionen Tonnen (2020) den größten Stoffstrom dar. Die Quoten des Baustoffrecyclings sind seit 2000 gestiegen, insbesondere bei mineralischen Abfällen. Dennoch wird der Großteil der recycelten Gesteinskörnungen in technisch weitgehend ungeregelten Anwendungen (z.B. Straßenbau) eingesetzt. Durch dieses Downcycling gehen wertvolle Ressourcen für technisch und wirtschaftlich wertvolle Anwendungen verloren. Das Forschungsprojekt upMIN100 geht der Frage nach, ob und inwieweit sich rezyklierte mineralische Bau- und Abbruchabfälle als Zusatzstoff in Lehmbaustoffen wie Lehmputzen und Lehmsteinen eignen. Der Fokus liegt dabei auf der Korngröße < 2 mm, die derzeit überwiegend deponiert wird, da es derzeit keine Vorschriften für den Einsatz in Bauprodukten gibt. Um den Einsatz von Bau- und Abbruchabfällen zu ermöglichen, müssen die technische Machbarkeit sichergestellt, Qualitätsanforderungen an die Ausgangsmaterialien (z.B. Grenzwerte für gesundheits- und umweltrelevante Schadstoffe und gefährliche Substanzen) und zulässige Anteile an rezyklierten Gesteinskörnungen definiert werden. Um negative Auswirkungen auf die Gebäudenutzer zu vermeiden, wurden die entwickelten Baumaterialien auf die in den mineralischen Abfällen enthaltenen Schadstoffe sowie auf Emissionen in die Innenraumluft geprüft. Außerdem sollen die aus mineralischen Abfällen hergestellten Lehmbauprodukte frei von Schadstoffen sein, um eine Rückführung in die Umwelt zu ermöglichen. Nach der Ersatzbaustoffverordnung (EBV) entspricht dies dem Kriterium BM-0. KW - Mineralische Baustoffe KW - Baustoffrecycling KW - Lehmbaustoffe PY - 2024 SN - 1868-0097 SP - 1 EP - 150 AN - OPUS4-61820 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Richter, Matthias T1 - Round robin tests of odour and VOC emissions from building products – What have we learned so far? N2 - Emission testing of volatile organic compounds (VOC) and odour from materials and products is commonly based on emission test chamber measurements. These measurements are often the basis of mandatory or voluntary labelling procedures. To ensure the comparability of results from different testing laboratories their performance must be verified. For this purpose, round robin tests (RRTs) are conducted. Bundesanstalt für Materialforschung und - prüfung (BAM) offers such a RRT every two years using well characterised test materials with defined VOC emissions. In addition to the VOC quantification, the evaluation of odour is also implemented in the round robin tests. At the beginning, only perceived intensity (PI) was tested but over the years also the acceptance evaluation was considered. In principle, the results of PI and acceptance evaluation are comparable. The advantage of PI is the lower number of panel members necessary for one evaluation. T2 - Healthy Buildings 2023 Europe CY - Aachen, Germany DA - 11.06.2023 KW - Perceived intensity KW - VOC-emission KW - Poficiency test KW - Chamber test KW - Odour PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-580001 SP - 434 EP - 436 PB - ISIAQ (International Society of Indoor Air Quality and Climate) CY - Herndon, VA, USA AN - OPUS4-58000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musyanovych, A. A1 - Grimmer, Christoph A1 - Sadak, A. E. A1 - Heßling, L. A1 - Bilsel, M. A1 - Horn, Wolfgang A1 - Richter, Matthias T1 - Polymeric Capsules with VOCs for Controlled Emission N2 - Micro-(nano-)encapsulation technology involves building of a barrier between the core and the environment and offers a number of benefits to preserve the functional and physicochemical properties of core material. Tremendous progress has been made in synthesizing well-defined capsules to achieve desired properties such as particle size, chemical composition, and controlled release of the payload. Encapsulation of volatile organic compounds (VOCs) that could evaporate with a defined rate is of immense interest for application in emission reference materials (ERM). These are urgently needed for quality assurance and quality control purposes (QA/QC) required by test standards for the determination of chemical emissions of construction and other materials for interior use. As such ERMs are hardly available on the market, the EU-funded EMPIR project MetrIAQ [1] was started to fill this gap by developing a material with temporally constant emission of VOCs typically found in indoor air. Different capsules in a size range between 5 and 50 μm were synthesized through an interfacial polyaddition/polycondensation reaction in direct (water-in-oil) system. As VOC several types of hydrophobic liquid materials were used. After synthesis, the morphology and physicochemical properties of capsules were characterized by electron microscopy, FTIR and DSC/TGA. An encapsulation efficiency up to 90% could be reached. The emission kinetic of volatile agents was studied in emission test chambers at 23 °C and 50% RH for 14 days. First results indicate that variation of the cross-linking grade of the shell material is one important parameter to adjust the desired emission rate. The overall aim is to achieve a consistent emission profile that decreases by less than 10 % over a target period of at least 14 days. T2 - 36th European Colloid & Interface Society Conference CY - Chania, Crete, Greece DA - 04.09.2022 KW - Capsules KW - Volatile organic compound KW - Polymer KW - Material emissions KW - Reference materials PY - 2022 AN - OPUS4-56039 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Richter, Matthias A1 - Wilke, Olaf T1 - Volatile organic compounds from building products - Results from seven proficiency tests with emission test chambers conducted between 2008 and 2021 N2 - Emission testing of volatile organic compounds (VOC) from materials and products is commonly based on emission test chamber measurements. To ensure the comparability of results from different testing laboratories their measurement performance must be verified. For this purpose, Bundesanstalt für Materialforschung und -prüfung (BAM) organizes an international proficiency test every two years using well-characterised test materials (one sealant, one furniture board and four times a lacquer) with defined VOC emissions. The materials fulfilled the requirements of homogeneity, reproducibility, and stability. Altogether, 41 VOCs were included of which 37 gave test chamber air concentrations between 10 and 98 µg/m³. This is the typical concentration range to be expected and to be quantified when performing chamber tests. Four compounds had higher concentrations between 250 and 1105 µg/m³. The relative standard deviations (RSD) of BAM proficiency tests since 2008 are compared and the improvement of the comparability of the emission chamber testing is shown by the decrease of the mean RSD down to 23% in 2021. In contrast, the first large European interlaboratory comparison in 1999 showed a mean RSD of 51%. T2 - Proficiency Testing in Analytical Chemistry, Microbiology and Laboratory Medicine CY - Windsor, United Kingdom DA - 25.09.2023 KW - Proficiency Test KW - VOC-Emission KW - Chamber-test PY - 2023 AN - OPUS4-59694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Klinge, A. A1 - Radeljic, L. A1 - Jann, Oliver T1 - Natural building materials for interior fitting and refurbishment - What about indoor emissions? N2 - Indoor air quality can be adversely affected by emissions from building materials, consequently having a negative impact on human health and well-being. In this study, more than 30 natural building materials (earth dry boards and plasters, bio-based insulation materials, and boards made of wood, flax, reed, straw, etc.) used for interior works were investigated as to their emissions of (semi-) volatile organic compounds ((S)VOC), formaldehyde, and radon. The study focused on the emissions from complete wall build-ups as they can be used for internal Partition walls and the internal insulation of external walls. Test chambers were designed, allowing the compounds to release only from the surface of the material facing indoors under testing Parameters that were chosen to simulate model room conditions. The emission test results were evaluated using the AgBB evaluation scheme, a procedure for the health-related evaluation of construction products and currently applied for the approval of specific groups of building materials in Germany. Seventeen out of 19 sample build-ups tested in this study would have passed this scheme since they generally proved to be low-emitting and although the combined emissions of multiple materials were tested, 50% of the measurements could be terminated before half of the total testing time. KW - Bio-based insulation KW - Earthen building materials KW - Volatile organic compounds KW - Semivolatile organic compounds KW - Radon PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-519634 DO - https://doi.org/10.3390/ma14010234 VL - 14 IS - 1 (Special issue: Measurement of the environmental impact of materials) SP - 234-1 EP - 234-14 PB - MDPI CY - Basel AN - OPUS4-51963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Richter, Matthias A1 - Jann, Oliver T1 - Volatile organic compounds from building products - Results from six round robin tests with emission test chambers conducted between 2008 and 2018 N2 - Emission testing of volatile organic compounds (VOC) from materials and products is commonly based on emission test chamber measurements. To ensure the comparability of results from different testing laboratories, their measurement performance must be verified. For this purpose, Bundesanstalt für Materialforschung und -prüfung (BAM) organizes an international proficiency test (round robin test, RRT) every two years using well-characterized test materials (one sealant, one furniture board, and four times a lacquer) with defined VOC emissions. The materials fulfilled the requirements of homogeneity, reproducibility, and stability. Altogether, 36 VOCs were included of which 33 gave test chamber air concentrations between 13 and 83 µg/m3. This is the typical concentration range to be expected and to be quantified when performing chamber tests. Three compounds had higher concentrations between 326 and 1105 µg/m3. In this paper, the relative standard deviations (RSD) of BAM round robin tests since 2008 are compared and the improvement of the comparability of the emission chamber testing is shown by the decrease of the mean RSD down to 28 % in 2018. In contrast, the first large European interlaboratory comparison in 1999 showed a mean RSD of 51 %. KW - Construction product KW - Emission test chamber KW - Interlaboratory comparison KW - Proficiency testing KW - Rround robin test KW - VOC emission PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526139 DO - https://doi.org/10.1111/ina.12848 VL - 31 IS - 6 SP - 2049 EP - 2057 PB - Wiley AN - OPUS4-52613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schröder, Simon Alexander A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Stephan, Ina A1 - Hohmann, Gloria A1 - Ziegert, Christof T1 - Identifikation und Einordnung von historischen Lehmbauteilen für die Wiederverwendung hinsichtlich Anreicherung von Schadstoffen und bauschädlichen Salzen T1 - Identification and classification of historical earth construction elements for recycling in respect of accumulation of pollutants and structurally damaging salts N2 - Lehmbaustoffe, einschließlich Lehm aus dem historischen Baubestand, bieten ein hohes Potenzial für ihre Wiederverwendbarkeit und die Schonung natürlicher Ressourcen. Zur Bewertung des Wiederverwendungspotenzials gibt es nur wenige Studien hinsichtlich der Schadstoffbelastung und der Anreicherung von Salzen in Gebäuden aus dem historischen Bestand. Tonminerale, die in Lehmbaustoffen als Bindemittel fungieren, können Schadstoffe binden. Die Region Mitteldeutschland ist geprägt durch jahrzehntelange Einwirkung erheblicher Schadstoffemissionen aus der Chemie- und Braunkohleindustrie. Der Eintrag von Schadstoffen in Lehmbaustoffe ist außerdem aus geogenen Hintergrundbelastungen denkbar, z. B. in Auenböden beeinflusst durch Einträge aus dem Erzbergbau. Salzbildende Anionen wie Chloride oder Nitrate können aufgrund ihrer hohen Löslichkeit mittels kapillarer Kräfte durch die Porenstruktur transportiert werden. In Lehmwänden können sie vor allem in oberflächennahen Lagen, in denen höhere Verdunstungsraten vorherrschen, durch Bindung mit in Lösung vorliegenden oder baustoffeigenen Kationen auskristallisieren und bauschädliche Salze ausbilden. Auch durch spezifische Nutzungen akkumulierte Schadstoffe, z. B. durch die Einwirkung von Tabakrauch, könnten theoretisch einer Wiederverwendung von Lehm entgegenstehen. In Anbetracht der Herausforderungen hinsichtlich der klimatischen und gesellschaftlichen Veränderungen, sind wissenschaftliche Erkenntnisse im Lehmbau erforderlich, die eine Integration in eine nachhaltige Kreislaufwirtschaft ermöglichen. Bei bisherigen Gesetzgebungsverfahren zu rezyklierten Baustoffen wurden Lehmbaustoffe noch nicht berücksichtigt. Ziel einer Vorstudie im Rahmen der WIR!-Initiative GOLEHM ist die Überprüfung der Wiederverwendbarkeit Wiederverwendbarkeit von Lehmbaustoffen aus historischen Bauten an Stichproben hinsichtlich der Umwelt- und Nutzerverträglichkeit. Für den Raum Mitteldeutschland können damit Anhaltspunkte darüber gegeben werden, welche Schadstoffe und bauschädlichen Salze in welchem Maße in Lehmbaustoffen aus dem Gebäudebestand erwartet werden können. Daraus können Hinweise zum Umgang mit Lehmbaustoffen aus historischen Gebäuden abgeleitet werden. Darüber hinaus wurden exemplarisch an zwei Gebäuden mikrobiologische Untersuchungen zur Ermittlung einer möglichen Belastung mit Schimmelpilzen vorgenommen. N2 - Earth construction materials, including earth from historical building stock, offer high potential in terms of their recyclability and sparing use of natural resources. Yet, only a few studies have been conducted on the levels of pollutants and the accumulation of salts in buildings from the historical building stock to enable an assessment of the potential for recycling. The aim of a preliminary study as part of the GOLEHM Initiative from WIR! is to use spot checks to review the recyclability of earth construction materials from historical buildings in terms of environmental impact and tolerance by users. This could provide indicators for the Central Germany region on which pollutants and structurally damaging salts can be expected in earth construction materials from the building stock and to what extent, allowing conclusions to be drawn on how to manage earth construction materials from historical buildings. Additionally, microbiological inspections of two sample buildings were performed to assess a potential contamination with mould. T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Wiederverwendung KW - Kreislaufwirtschaft KW - Schadstoffe KW - Bauschädliche Salze PY - 2024 SP - 1 EP - 8 CY - Weimar AN - OPUS4-61883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grimmer, Christoph A1 - Richter, Matthias A1 - Neuhaus, T. A1 - Prinz, Carsten A1 - Strzelczyk, Rebecca Skadi A1 - Colakoglu, Irem A1 - Horn, Wolfgang T1 - Towards a multi-VOC emission reference material with temporally constant emission profile for QA/QC of materials emission testing procedures N2 - Emission reference materials (ERMs) are sought after to further control and improve indoor air quality. The impregnation of porous materials with volatile organic compounds (VOCs) is a promising approach to produce ERMs. Different VOCs were used to impregnate various porous materials (mainly zeolites, activated carbons and a metal organic framework). The influence of different methodological parameters and material properties were studied to optimize the impregnation procedure and to find the best material/VOC combination. The impregnation procedure remains quite irreproducible, nevertheless, very good ERM candidates were identified. Two materials (zeolite 4 and AC 1 impregnated with n-hexadecane) showed a very stable emission over 14 days (<10 % change). Another material (AC 1 impregnated with toluene) showed a declining emission profile but with a very good in-batch reproducibility and a storage stability of up to 12 months. KW - Emission reference material KW - Porous materials KW - Indoor air quality KW - Emission test chamber KW - CO2 assisted impregnation KW - EN 16516 PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612238 DO - https://doi.org/10.1016/j.chemosphere.2024.143437 SN - 1879-1298 VL - 366 SP - 1 EP - 8 PB - Elsevier AN - OPUS4-61223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klinge, A A1 - Mönig, J A1 - Ziegert, C A1 - Richter, Matthias A1 - Kalbe, Ute A1 - Horn, Wolfgang A1 - Röhlen, U A1 - Rauscher, S A1 - Roswag-Klinge, E T1 - upMIN 100 – upcycling of mineral construction and demolition waste to substitute natural aggregates in earthen building materials N2 - The construction sector is one of the most resource-intensive sectors in Germany and is responsible for 40 % of CO2 emissions. Around 517 million tons of mineral raw materials are required annually for the construction of buildings in Germany. At the same time, mineral construction waste was the largest material flow at 229.3 million tons (2020). The rates of construction and demolition waste (CDW) recycling have increased since 2000, especially for mineral waste. Nevertheless, the majority of recycled aggregates are used in technically largely unregulated applications (e.g. road construction). This downcycling leads to a loss of valuable resources for technically and economically valuable applications. The upMIN 100 research project is investigating the question of whether and to what extent recycled CDW is suitable as an additive an binder in earthen building materials. The focus is placed on grain sizes of < 2 mm, which are currently predominantly landfilled, as there are at present no regulations for their use in building products. The soil matrix of earthen building materials however, naturally contains of different grain sizes, whith < 2mm – 0,063 for aggregates and < 0.063 mm as a binder. Therefore, the focused grain sizes (sand, clay and silt) could have a high usage potential. In order to enable the use of CDW, the technical feasibility must be ensured, quality requirements for source materials (e.g. threshold values for pollutants in terms of health and environmental compatibility and hazardous substances) and permissible proportions of recycled aggregates must be defined. Two different building material developments (earth blocks and -plaster)were used to assess both, the technical feasibility as well the pollutant content of the recycled aggregate and its final emissions into the indoor air. For both materials two mixtures could be established, that also meet the mechanical specifications according to the DIN standard, such as the compressive strength. A method was developed to design material mixtures with a high amount of CDW that comply with the defined limit values. The mixtures reached a recycling rate of 28 % with high mechanical properties and 70 % with minimum strength requirements. KW - Mineral waste KW - Upcycling KW - Earthen building product KW - Circular construction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652831 DO - https://doi.org/10.1088/1755-1315/1554/1/012084 SN - 1755-1307 VL - 1554 IS - 1 SP - 1 EP - 9 PB - IOP Publishing AN - OPUS4-65283 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -