TY - JOUR A1 - Moritz, W. A1 - Werner, R. A1 - Tausche, A. A1 - Cherkaschinin, G. A1 - Molajew, R. A1 - Wirth, Thomas A1 - Unger, Wolfgang A1 - Linke, S. T1 - Alloys for gas sensors investigated using the continuous gradient-high throughput screening macroscope CG-HTSM N2 - Ternary alloys have been studied as the gate metal of chemical sensors based on the field effect in silicon. The investigation of reduced poisoning of hydrogen sensors by H2S is presented in the alloy system PdxNiyCo1-x-y. A new method in high throughput screening of alloys is applied. Not singular sample compositions but a continuous gradient in alloy concentrations was produced on a semiconductor sample. A laser scanning system produces a photo current in the semiconductor to map the sensor signal and provide a quasi continuous alloy characterization. The new system is therefore called Continuous Gradient—High Throughput Screening Macroscope (CG-HTSM). Typically 625 alloys are characterized in 15 minutes. The resolution of our set-up allows distinguishing 100.000 alloy compositions. KW - Alloy KW - Sensor KW - High throughput screening KW - Macroscope PY - 2011 DO - https://doi.org/10.1166/sl.2011.1586 SN - 1546-198X SN - 1546-1971 VL - 9 IS - 2 SP - 662 EP - 664 PB - American Scientific Publishers (ASP) CY - Stevenson Ranch, CA, USA AN - OPUS4-24504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holzweber, Markus A1 - Lippitz, Andreas A1 - Hesse, R. A1 - Denecke, R. A1 - Werner, W. A1 - Unger, Wolfgang T1 - The use of ionic liquids for the determination of the spectrometer transmission function in X-ray photoelectron spectroscopy (XPS) N2 - The uncertainty of measurement in quantitative XPS analysis can be reduced by using a calibrated spectrometer transmission function T (E), which is usually determined by taking spectra from Au, Ag, Cu and Ge elemental reference materials. However, this approach is quite time-consuming due to required sample preparation steps like sputter cleaning etc., and the relatively big number of samples to be measured. This contribution proposes the use of the ionic liquids [C2C1im][NTf2] and [C3C1im][NTf2] as reference materials for a determination of T(E). These multi-elemental samples deliver five intensive photoemission peaks, F 1s, O 1s, N 1s, C 1s and S 2p, in an energy window from 160 eV to 700 eV which is of specific interest for applications of quantitative XPS for surface chemical analysis of soft matter, one of the major applications of XPS. KW - Quantitative XPS KW - Ionic liquid KW - Transmission function PY - 2019 DO - https://doi.org/10.1016/j.elspec.2019.03.008 VL - 233 SP - 51 EP - 56 PB - Elsevier B.V. AN - OPUS4-48019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Bruno, Giovanni A1 - Buffière, J.-Y. A1 - Wegener, T. A1 - Niendorf, T. A1 - Wu, T. A1 - Zhang, X. A1 - Kashaev, N. A1 - Meneghetti, G. A1 - Hrabe, Nik A1 - Madia, Mauro A1 - Werner, Tiago A1 - Hilgenberg, Kai A1 - Koukolikova, M. A1 - Prochazka, R. A1 - Dzugan, J. A1 - Möller, B. A1 - Beretta, S. A1 - Evans, Alexander A1 - Wagener, R. A1 - Schnabel, K. T1 - Damage tolerant design of additively manufactured metallic components subjected to cyclic loading: State of the art and challenges N2 - This article is an outcome of a workshop on Fatigue of Additive Manufactured Metallic Components jointly organized by the Federal Institute for Materials Research and Testing (BAM) Berlin, Germany and the National Institute of Standards and Technology (NIST) Boulder, CO, U.S.A. The aim of the workshop was a comprehensive discussion of the specific aspects of additively manufactured (AM) components in regard to failure under cyclic loading. Undoubtedly, a better understanding and the further development of approaches for damage tolerant component design of AM parts are among the most significant challenges currently facing the use of these new technologies. This article presents a thorough overview of the workshop discussions. It aims to provide a review of the parameters affecting the damage tolerance of AM parts with special emphasis on the process parameters intrinsic to the AM technologies, the resulting defects and residual stresses. Based on these aspects, concepts for damage tolerant component design for AM are reviewed and critically discussed. KW - Additive manufacturing KW - Fatigue loading KW - Component assessment KW - Damage tolerance KW - Defects KW - Residual stresses PY - 2021 DO - https://doi.org/10.1016/j.pmatsci.2021.100786 SN - 0079-6425 VL - 121 PB - Elsevier CY - Amsterdam AN - OPUS4-51937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seah, M.P. A1 - Spencer, S.J. A1 - Bensebaa, F. A1 - Vickridge, I. A1 - Danzebrink, H. A1 - Krumrey, M. A1 - Gross, Thomas A1 - Österle, Werner A1 - Wendler, E. A1 - Rheinländer, B. A1 - Azuma, Y. A1 - Kojima, I. A1 - Suzuki, N. A1 - Suzuki, M. A1 - Tanuma, S. A1 - Moon, D.W. A1 - Lee, H.J. A1 - Cho, H.M. A1 - Chen, H.Y. A1 - Wee, A. T. S. A1 - Osipowicz, T. A1 - Pan, J.S. A1 - Jordaan, W.A. A1 - Hauert, R. A1 - Klotz, U. A1 - van der Marel, C. A1 - Verheijen, M. A1 - Tamminga, Y. A1 - Jeynes, C. A1 - Bailey, P. A1 - Biswas, S. A1 - Falke, U. A1 - Nguyen, N.V. A1 - Chandler-Horowitz, D. A1 - Ehrstein, J.R. A1 - Muller, D. A1 - Dura, J.A. T1 - Critical review of the current status of thickness measurements for ultrathin SiO2 on Si - Part V: Results of a CCQM pilot study N2 - Results are reported from a pilot study under the Consultative Committee for Amount of Substance (CCQM) to compare measurements of and resolve any relevant measurement issues in, the amount of thermal SiO2 oxide on (100) and (111) orientation Si wafer substrates in the thickness range 1.5 - 8 nm. As a result of the invitation to participate in this activity, 45 sets of measurements have been made in different laboratories using 10 analytical methods: medium-energy ion scattering spectrometry (MEIS), nuclear reaction analysis (NRA), RBS, elastic backscattering spectrometry (EBS), XPS, SIMS, ellipsometry, grazing-incidence x-ray reflectrometry (GIXRR), neutron reflectometry and transmission electron microscopy (TEM). The measurements are made on separate sets of 10 carefully prepared samples, all of which have been characterised by a combination of ellipsometry and XPS using carefully established reference conditions and reference parameters. The results have been assessed against the National Physical Laboratory (NPL) data and all show excellent linearity. The remaining data sets correlate with the NPL data with average root-mean-square scatters of 0.15 nm, half being better than 0.1 nm and a few at or better than 0.05 nm. Each set of data allows a relative scaling constant and a zero thickness offset to be determined. Each method has an inherent zero thickness offset between 0 nm and 1 nm and it is these offsets, measured here for the first time, that have caused many problems in the past. There are three basic classes of offset: water and carbonadeous contamination equivalent to ~1 nm as seen by ellipsometry; adsorbed oxygen mainly from water at an equivalent thickness of 0.5 nm as seen by MEIS, NRA, RBS and possibly GIXRR; and no offset as seen by XPS using the Si 2p peaks. Each technique has a different uncertainty for the scaling constant and consistent results have been achieved. X-Ray photoelectron spectroscopy has large uncertainties for the scaling constant but a high precision and, critically, if used correctly, has zero offset. Thus, a combination of XPS and the other methods allows the XPS scaling constant to be determined with low uncertainty, traceable via the other methods. XPS laboratories returning results early were invited to test a new reference procedure. All showed very significant improvements. The reference attenuation lengths thus need scaling by 0.986 ± 0.009 (at an expansion factor of 2) deduced from the data for the other methods. Several other methods have small offsets and, to the extent that these can be shown to be constant or measurable, then these methods will also show low uncertainty. Recommendations are provided for parameters for XPS, MEIS, RBS and NRA to improve their accuracy. KW - Calibration KW - Ellipsometry KW - GIXRR KW - Interlaboratory study KW - MEIS KW - Neutron reflectometry KW - NRA KW - RBS KW - Silicon dioxide KW - SIMS KW - XPS PY - 2004 DO - https://doi.org/10.1002/sia.1909 SN - 0142-2421 SN - 1096-9918 VL - 36 IS - 9 SP - 1269 EP - 1303 PB - Wiley CY - Chichester AN - OPUS4-5549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Seah, M.P. A1 - Spencer, S.J. A1 - Bensebaa, F. A1 - Vickridge, I. A1 - Danzebrink, H. A1 - Krumrey, M. A1 - Gross, Thomas A1 - Österle, Werner A1 - Wendler, E. A1 - Rheinländer, B. A1 - Azuma, Y. A1 - Kojima, I. A1 - Suzuki, N. A1 - Suzuki, M. A1 - Tanuma, S. A1 - Moon, D.W. A1 - Lee, H.J. A1 - Cho, H.M. A1 - Chen, H.Y. A1 - Wee, A. T. S. A1 - Osipowicz, T. A1 - Pan, J.S. A1 - Jordaan, W.A. A1 - Hauert, R. A1 - Klotz, U. A1 - van der Marel, C. A1 - Verheijen, M. A1 - Tamminga, Y. A1 - Jeynes, C. A1 - Bailey, P. A1 - Biswas, S. A1 - Falke, U. A1 - Nguyen, N.V. A1 - Chandler-Horowitz, D. A1 - Ehrstein, J.R. A1 - Muller, D. A1 - Dura, J.A. T1 - Ultra-thin SiO2 on Si, Part V: Results of a CCQM Pilot Study of Thickness Measurements KW - SiO2 KW - Thin films KW - Thickness KW - XPS KW - Ellipsometry KW - TEM PY - 2003 SN - 1473-2734 SP - 57 pages AN - OPUS4-4118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moldovan, R.-P. A1 - Wenzel, B. A1 - Teodoro, R. A1 - Neumann, W. A1 - Dukic-Stefanovic, S. A1 - Kraus, Werner A1 - Rong, P. A1 - Deuther-Conrad, W. A1 - Hey-Hawkins, E. A1 - Krügel, U. A1 - Brust, P. T1 - Studies towards the development of a PET radiotracer for imaging of the P2Y1 receptors in the brain: synthesis, 18F-labeling and preliminary biological evaluation N2 - Purine nucleotides such as ATP and ADP are important extracellular signaling molecules in almost all tissues activating various subtypes of purinoreceptors. In the brain, the P2Y1 receptor (P2Y1R) subtype mediates trophic functions like differentiation and proliferation, and modulates fast synaptic transmission, both suggested to be affected in diseases of the central nervous system. Research on P2Y1R is limited because suitable brain-penetrating P2Y1R-selective tracers are not yet available. Here, we describe the first efforts to develop an 18F-labeled PET tracer based on the structure of the highly affine and selective, non-nucleotidic P2Y1R allosteric modulator 1-(2-[2-(tert-butyl)phenoxy]pyridin-3-yl)-3- [4-(trifluoromethoxy)phenyl]urea (7). A small series of fluorinated compounds was developed by systematic modification of the p-(trifluoromethoxy)phenyl, the urea and the 2-pyridyl subunits of the lead compound 7. Additionally, the p-(trifluoromethoxy)phenyl subunit was substituted by carborane, a boron-rich cluster with potential applicability in boron neutron capture therapy (BNCT). By functional assays, the new fluorinated derivative 1-{2-[2-(tert-butyl)phenoxy]pyridin-3-yl}-3-[4-(2-fluoroethyl) phenyl]urea (18) was identified with a high P2Y1R antagonistic potency (IC50 ¼10 nM). Compound [18F] 18 was radiosynthesized by using tetra-n-butyl ammonium [18F]fluoride with high radiochemical purity, radiochemical yield and molar activities. Investigation of brain homogenates using hydrophilic interaction chromatography (HILIC) revealed [18F]fluoride as major radiometabolite. Although [18F]18 showed fast in vivo metabolization, the high potency and unique allosteric binding mode makes this class of compounds interesting for further optimizations and investigation of the theranostic potential as PET tracer and BNCT agent. KW - Purine P2Y1 receptors KW - Positron emission tomography KW - Brain PET tracers KW - Radiometabolites KW - Micellar chromatography KW - Hydrophilic interaction chromatography PY - 2019 DO - https://doi.org/10.1016/j.ejmech.2019.01.006 SN - 0223-5234 VL - 165 SP - 142 EP - 159 PB - Elsevier CY - Amsterdam AN - OPUS4-47253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Ekenhorst, Derk A1 - Brzezinka, Klaus-Werner A1 - Hentschel, Manfred P. ED - Krenkel, W. T1 - Fiber Induced Failure of Carbon/Carbon Composites T2 - 4th International Conference on High Temperature Ceramic Matrix Composites ; 4th HT-CMC Conference CY - Munich, Germany DA - 2001-10-01 PY - 2001 SN - 3-527-30320-0 VL - 4 SP - 175 EP - 180 PB - Wiley-VCH CY - Weinheim AN - OPUS4-1289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Storek, Werner A1 - Kosslick, H. A1 - Lischke, G. A1 - Parlitz, B. A1 - Fricke, R. T1 - Acidity and active sites of Al-MCM-41 N2 - The influence of the aluminum contents of MCM-41 (Si/Al ratio varied between 2.7 and 69) on the coordination of Al, on the acidity, and on the catalytic properties is studied by 27Al MAS NMR, temperature programmed desorption of ammonia, and the conversion of acetone. Based on TPDA results, an assignment of the peaks of desorption of ammonia is proposed. With low Al contents, the concentration of strong Brønsted acid sites, which are attributed to tetrahedral aluminum, increases with growing Al amounts. At higher Al contents, however, the number of strong acid sites decreases again. Besides usual strong Brønsted sites, TPDA reveals the existence of weak Brønsted and Lewis sites and of Lewis sites of a high acidic strength. Separation between the two types of sites of weak acidity is incomplete. In the temperature programmed decomposition of NH4-exchanged MCM-41 samples, strong Lewis acid sites temporarily re-adsorb ammonia generated by the thermal decomposition of the NH4+ ions located at the Brønsted sites. Ammonia re-adsorption at Lewis sites results in a shift of the maximum of the TPDA peak to a higher temperature. Calcination of samples leads to the formation of strong Lewis sites at the expense of Brønsted sites. To evaluate the acidity of Al-MCM-41, recording of decomposition profiles has been extended to Ga- and Fe-MCM-41. Catalytic activity in the conversion of acetone reaches its maximum with the sample based on Al-MCM-41 with the molar Si/Al ratio of 6.85. Highly favored formation of isobutene points to a comparably high acidic strength of the active sites. KW - MCM-41 PY - 1999 DO - https://doi.org/10.1016/S0926-860X(99)00078-2 SN - 0926-860X SN - 1873-3875 VL - 184 IS - 1 SP - 49 EP - 60 PB - Elsevier CY - Amsterdam AN - OPUS4-740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Richter, M. A1 - Trunschke, A. A1 - Bentrup, U. A1 - Brzezinka, Klaus-Werner A1 - Schreier, E. A1 - Schneider, M. A1 - Pohl, M.-M. A1 - Fricke, R. T1 - Selective Catalytic Reduction of Nitric Oxide by Ammonia over Egg-Shell MnOx/NaY Composite Catalysts N2 - A novel composite catalyst system for the selective catalytic reduction (SCR) of NOx by NH3 is described operating at temperatures lower than 470 K in the presence of water with NO conversions of 80–100% at space velocities of 30,000–50,000 h-1. The catalyst is prepared by egg-shell precipitation of MnO2 on the external surface of zeolite NaY. Structural and thermal stability of precipitated MnO2 as well as of the MnO2/NaY composite catalyst were characterized by N2 adsorption, X-ray diffraction, laser Raman spectroscopy, temperature-programmed reduction, and electron microscopy. MnO2 precipitated on zeolite NaY (15 wt% loading) retained its amorphous state up to calcination temperatures of 775 K. The zeolite component remained structurally intact. Calcination at higher temperatures destroyed the zeolite structure and transformed MnO2 into Mn3O4. DRIFT spectroscopic investigations revealed the presence of symmetric O=N—O—N=O species formally corresponding to N2O3 on the composite catalyst after contact with NO. Catalytic measurements under integral flow conditions showed that the catalyst performance is associated with a close coupling of nitrite formation and its drain off from equilibria with NO/NO2 and nitrate by ammonia. Several results are in line with the “diazotation” mechanism, including NH3 protonation to NH4+, whereas prevailing Lewis acid sites should enable NH3 activation via amide species, thus leading to a parallel “amide/nitrosamide” SCR reaction route. The activity-temperature profile fulfills the requirements of a low-temperature NOx reduction catalyst for mobile diesel engines if an ammonia supply is implemented “on board,” e.g., by urea decomposition. PY - 2002 DO - https://doi.org/10.1006/jcat.2001.3468 SN - 0021-9517 SN - 1090-2694 VL - 206 SP - 98 EP - 113 PB - Acad. Press CY - San Diego, Calif. AN - OPUS4-1638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Drews, A. A1 - Pietzsch, H.-J. A1 - Syhre, R. A1 - Seifert, S. A1 - Varnäs, K. A1 - Hall, H. A1 - Halldin, C. A1 - Kraus, Werner A1 - Karlsson, P. T1 - Synthesis and biological evaluation of technetium(III) mixed-ligand complexes with high affinity for the cerebral 5-HT1A receptor and the alpha-1-adrenergic receptor N2 - Tc(III) and Re(III) complexes [M(NS3)(CNR)] (M = Re, 99mTc, NS3 = 2,2?,2?-nitrilotris(ethanethiol), CNR = functionalized isocyanide bearing a derivative of WAY 100635) have been synthesized and characterized. Re was used as Tc surrogate for chemical characterization and in vitro receptor-binding studies. For two representatives subnanomolar affinities for the 5-HT1A as well as for the alpha1-adrenergic receptor were reached. Biodistribution studies in rats of the 99mTc complexes showed brain uptakes between 0.3 and 0.5% ID/organ (5 min p.i.). In vitro autoradiography of one 99mTc representative in sections of post mortem human brain indicate its accumulation in 5-HT1A receptor-rich brain regions. However, addition of the specific 5-HT1A receptor agonist 8-OH-DPAT as well as the alpha1-adrenoceptor antagonist prazosin could not substantially block this tracer accumulation. A preliminary SPET study in a monkey showed negligible brain uptake. KW - 5-HT1A receptor KW - Alpha 1-adrenergic receptor KW - Technetium-99m KW - Rhenium KW - Autoradiography KW - SPET PY - 2002 DO - https://doi.org/10.1016/S0969-8051(02)00296-2 SN - 0883-2897 VL - 29 IS - 4 SP - 389 EP - 398 PB - Elsevier Science Inc. CY - New York, NY AN - OPUS4-1553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heimbold, I. A1 - Drews, A. A1 - Kretzschmar, M. A1 - Varnäs, K. A1 - Hall, H. A1 - Halldin, C. A1 - Syhre, R. A1 - Kraus, Werner A1 - Pietzsch, H.-J. T1 - Synthesis, Biological and Autoradiographic Evaluation of a Novel Tc-99m Radioligand derived from WAY 100635 with High Affinity for the 5-HT1A Receptor and the alpha1-Adrenergic Receptor N2 - This paper reports the synthesis, biological evaluation, in vitro and ex vivo autoradiography of the first Tc-99m ligand with subnanomolar affinity for the 5-HT1A receptor and a remarkably high affinity for the alpha1-adrenergic receptor. The neutral “3+1” mixed-ligand complex combines 4-(6-mercaptohexyl)-1-(2-methoxyphenyl)piperazine as monodentate and 3-(N-methyl)azapentane-1,5-dithiol as tridentate unit with oxotechnetium(V). The analogous rhenium complex was synthesized for complete structural characterization and used in receptor binding assays. In competition experiments both complexes display subnanomolar affinity for the 5-HT1A receptor (IC500.24 nM for Re, 0.13 nM for Tc) but also very high affinities for the alpha1-adrenergic receptor (IC50 0.05 nM for Re, 0.03 nM for Tc). Biodistribution studies show a brain uptake in rat of 0.22% ID five minutes post injection. In vitro autoradiographic studies in rat brain and postmortem human brain indicate accumulation of the Tc-99m complex in brain areas which are rich in 5-HT1A receptors or in alpha1-adrenergic receptors. This in vitro enrichment can be blocked respectively by the 5-HT1A receptor agonist 8-OH-DPAT or by prazosin hydrochloride, an alpha1-adrenergic receptor antagonist. Ex vivo autoradiographic studies in rats show a slight accumulation of the Tc-99m complex in 5-HT1A receptor-rich areas of the brain, which could not be blocked, as well as in regions rich in alpha1-adrenergic receptors, which could be blocked by prazosin hydrochloride. KW - Serotonin-5-HT1A receptor KW - Tc-99m receptor ligand KW - WAY100635 analogue KW - Ligand synthesis KW - In vitro and ex vivo autoradiography KW - Receptor binding assay PY - 2002 DO - https://doi.org/10.1016/S0969-8051(01)00313-4 SN - 0883-2897 VL - 29 SP - 375 EP - 387 PB - Elsevier Science Inc. CY - New York, NY AN - OPUS4-1554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rother, A. A1 - Kniess, T. A1 - Bergmann, R. A1 - Kraus, Werner A1 - Jungclas, H. A1 - Spies, H. ED - Marino, N. T1 - Investigations on redox-active pyridium salt - dihydropyridine bearing Tc- and Re- complexes T2 - 6th International Symposium on Technetium in Chemistry and Nuclear Medicine CY - Bressanone, Italy DA - 2002-09-04 PY - 2002 SN - 88-86281-73-0 N1 - Serientitel: Technetium, rhenium and other metals in chemistry and nuclear medicine – Series title: Technetium, rhenium and other metals in chemistry and nuclear medicine VL - 6 IS - 6 SP - 73 EP - 78 PB - SGEditoriali CY - Padova AN - OPUS4-1558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram A1 - Hässelbarth, Werner A1 - Hirlehei, U. A1 - Hotze, H.-J. A1 - Mickan, B. A1 - Kramer, R. A1 - Dopheide, D. T1 - Uncertainty Analysis and Long-Term Stability Investigation of the German Primary High Pressure Natural Gas Test Facility pigsar T2 - 11th FLOMEKO CY - Groningen, The Netherlands DA - 2003-05-12 PY - 2003 CY - [Groningen] AN - OPUS4-2653 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meißner, T. A1 - Bergmann, R. A1 - Oswald, J. A1 - Rode, K. A1 - Stephan, H. A1 - Richter, W. A1 - Zänker, H. A1 - Kraus, Werner A1 - Emmerling, Franziska A1 - Reck, Günter T1 - Chitosan-encapsulated Keggin anion [Ti2W10PO40]7-.Synthesis, characterization and cellular uptake studies N2 - The Keggin type polyoxotungstate [Ti2W10PO40]7- forms stable associates with the biopolymer chitosan in the nanometer size range. The cluster compound crystallizes from aqueous solution as K4H3[Ti2W10PO40] · 15H2O having a tetragonal structure. Both, the cluster compound and the chitosan/[Ti2W10PO40] associates show a high hydrolytic stability at pH 7.4. The associates formed between the cluster anion [Ti2W10PO40]7- with the polyaminosaccharide chitosan have been characterized by photon correlation spectroscopy, scanning electron microscopy, filtration, centrifugation and zeta potential measurements. The size of the associates formed is in the range of ca. 5×101 to 5×102 nm. These particles have a defined stoichiometry with 5–6 cluster anions bound per molecule chitosan. The isoelectric point determined by zeta potential measurements was found for a cluster anion to chitosan molar ratio of 5.5, indicating the charge neutralization between protonated chitosan and [Ti2W10PO40]7- anions. Cellular uptake studies with [Ti2W10PO40]7- using tumor cell lines FaDu (human squamous carcinoma) and HT-29 (human adenocarcinoma) showed that the tungsten amount inside the cells is remarkably enhanced in the presence of chitosan. KW - Cluster compound KW - Keggin structure KW - Bipolymer KW - Chitosan PY - 2006 DO - https://doi.org/10.1007/s11243-006-0035-z SN - 0340-4285 SN - 1572-901X VL - 31 IS - 5 SP - 603 EP - 610 PB - Springer CY - Dordrecht AN - OPUS4-12568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bathke, Werner A1 - Philippovich, N. A1 - Stickler, R. A1 - Frieler, K. T1 - Brazing under microgravity - TEXUS II experiment T2 - 3rd European Symposium on Material Science in Space ; 3éme Symposium Européen de Science des Matériaux dans l'Espace CY - Grenoble, France DA - 1979-04-24 PY - 1979 SN - 0379-6566 N1 - Serientitel: ESA SP – Series title: ESA SP IS - 142 SP - 95 EP - 100 PB - European Space Agency CY - Neuilly AN - OPUS4-9207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bathke, Werner A1 - Philippovich, N. A1 - Stickler, R. A1 - Frieler, K. ED - Faust, D. T1 - Brazing of capillary gaps under microgravity - sounding rocket project TEXUS II PY - 1979 SP - 1 EP - 38 PB - Deutsche Forschungs- u. Versuchsanstalt für Luft- und Raumfahrt e.V. CY - Köln AN - OPUS4-9208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Daum, Werner A1 - Werthschützky, R. T1 - Strukturintegrierte Sensorik PY - 2012 DO - https://doi.org/10.1524/teme.2012.9026 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 79 IS - 7-8 SP - 335 EP - 336 PB - Oldenbourg CY - München AN - OPUS4-26386 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stößer, R. A1 - Brenneis, Rudolf A1 - Herrmann, Werner A1 - Steinfeldt, N. ED - Petzow, G. T1 - Nachweis mechanisch induzierter Strukturänderungen bei Druck- bzw. Biegebelastung hochkorundhaltiger Werkstoffe mit Hilfe der Elektronenspinresonanz T2 - Beiträge zum Abschlußkolloquium im Schwerpunktprogramm "Keramische Hochleistungswerkstoffe" der Deutschen Forschungsgemeinschaft CY - Stuttgart, Deutschland DA - 1994-02-17 PY - 1996 SN - 3-527-27138-4 SP - 287 EP - 297 PB - VCH CY - Weinheim AN - OPUS4-12653 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mirtschink, P. A1 - Stehr, S.N. A1 - Pietzsch, H.J. A1 - Bergmann, R. A1 - Pietzsch, J. A1 - Wunderlich, G. A1 - Heintz, A.C. A1 - Kropp, J. A1 - Spies, H. A1 - Kraus, Werner A1 - Deussen, A. A1 - Walther, M. T1 - Modified "4+1" Mixed Ligand Technetium-Labeled Fatty Acids for Myocardial Imaging: Evaluation of Myocardial Uptake and Biodistribution N2 - Our group previously synthesized 99mTc-labeled fatty acids suitable for myocardial metabolism and flow imaging. In this set of experiments, 29 new analogues were synthesized according to the “4 + 1” mixed ligand approach with some specific differences. Conventional “4 + 1” 99mTc-fatty acids are built in the sequence: Tc-chelate, alkyl chain, and carboxylic group. We developed compounds following a new design with the sequence: carboxylic group, alkyl chain, Tc-chelate, and lipophilic tail. Therefore, the 99mTc-chelate was transferred to a more central position of the compound, aiming toward an improved myocardial profile and an accelerated liver clearance. In this context, several functional groups incorporated in the lipophilic tail section were tested to evaluate their influence on the compound's character. In addition to biodistribution studies in vivo, the myocardial first-pass extraction of the compounds was tested in an isolated Langendorff rat heart model. A satisfactory myocardial uptake of up to 20% of the injected dose (% ID) in the perfused heart and a fast liver clearance in vivo with only 0.29% ID/g at 60 min postinjection demonstrate that the induced molecular modifications affect the kinetics of 99mTc-radiolabeled fatty acid compounds favorably. From the data set, rules for estimating the biodistribution of fatty acids tracers are deduced. PY - 2008 DO - https://doi.org/10.1021/bc700164c SN - 1043-1802 SN - 1520-4812 VL - 19 IS - 1 SP - 97 EP - 108 CY - Washington, DC AN - OPUS4-16499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Senoner, Mathias A1 - Wirth, Thomas A1 - Unger, Wolfgang A1 - Österle, Werner A1 - Kaiander, I. A1 - Sellin, R. L. A1 - Bimberg, D. ED - Wilkening, G. ED - Koenders, L. T1 - Testing the Lateral Resolution in the Nanometre Range with a New Type of Certified Reference Material T2 - NanoScale 2004 Seminar ; 6th Seminar on Quantitative Microscopy ; 2nd Seminar on Nanoscale Calibration Standards and Methods CY - Braunschweig, Germany DA - 2004-03-25 KW - Laterale Auflösung KW - Nanometrologie KW - Nanotechnologie KW - Oberflächenanalytik KW - Zertifiziertes Referenzmaterial PY - 2004 SN - 3-527-40502-X DO - https://doi.org/10.1002/3527606661.ch21 SP - 282 EP - 294 PB - Wiley-VCH CY - Weinheim AN - OPUS4-7541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -