TY - JOUR A1 - Zerbst, Uwe A1 - Vormwald, M. A1 - Pippan, R. A1 - Gänser, H.-P. A1 - Sarrazin-Baudoux, C. A1 - Madia, Mauro T1 - About the fatigue crack propagation threshold of metals as a design criterion - A review N2 - The fatigue crack propagation threshold ΔKth is of paramount importance for any kind of damage tolerant design, but in contrast to this importance, the determination and application of the parameter is not on the firm ground as previously assumed. The paper discusses questions of its experimental determination as well as of its application to components. In both fields, new questions have been raised with the potential to challenge or modify long-standing knowledge. Against this background, the paper is an attempt to systematize the established knowledge as well as questions and open issues. KW - Fatigue crack propagation threshold KW - Experimental determination KW - Influencing factors KW - Transferability to components PY - 2016 DO - https://doi.org/10.1016/j.engfracmech.2015.12.002 SN - 0013-7944 SN - 1873-7315 VL - 153 SP - 190 EP - 243 PB - Elsevier Science CY - Kidlington AN - OPUS4-35264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Beier, T. T1 - IBESS: Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen - eine Einführung T2 - DVS-Congress 2015 CY - Nürnberg DA - 2015-09-14 PY - 2015 AN - OPUS4-33500 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Zerbst, Uwe T1 - Application of the cyclic R-curve method in notch fatigue analysis N2 - The paper deals with the prediction of the fatigue Limit of notched specimens. Some authors in the literature have shown that this issue can be solved by employing an approach based on critical distances, others used elastic fracture mechanics. In this paper the fatigue limit of notched specimens is given by the non-propagating condition of mechanically small surface cracks. According to the so-called cyclic R-curve method, the crack driving force of a growing small crack is compared to its resistance force, which incorporates the gradual build-up of crack closure. The fatigue limit is determined by that applied nominal stress, for which the tangency condition of crack driving and resistance force is satisfied. The approach has been modified to incorporate plasticity effects in the mechanically short crack Regime and it has been applied to a mild and a high-strength steel, in case of an infinite plate with circular hole under remote tensile stress. The method has been successfully applied to the evaluation of fatigue notch-sensitivity in case of surface roughness. KW - Notch fatigue KW - Notch sensitivity KW - Cyclic R-curve KW - Non-propagating cracks KW - Critical distance PY - 2016 DO - https://doi.org/10.1016/j.ijfatigue.2015.06.015 SN - 0142-1123 VL - 82 IS - 1 SP - 71 EP - 79 PB - Elsevier Ltd. CY - Oxford, UK AN - OPUS4-35298 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe T1 - Bruchmechanische Bestimmung der Schwingfestigkeit basierend auf der zyklischen R-Kurve N2 - Konventionell wird in der Bauteilauslegung zwischen Konzepten der Schwing- und Betriebsfestigkeit auf der einen und der Bruchmechanik auf der anderen Seite unterschieden. Werden in der Schwingfestigkeitsbewertung Gesamtlebensdauern ermittelt, so sind es in der Bruchmechanik Restlebensdauern bei Vorhandensein eines größeren, d.h., bereits zerstörungsfrei auffindbaren Risses. Daneben gibt es seit längerem Bestrebungen, bruchmechanische Ansätze auch für die Ermittlung der Gesamtlebensdauer fruchtbar zu machen. Der besondere Wert einer solchen Kombination besteht darin, dass die Bruchmechanik die explizite theoretische Behandlung von Eingangsparametern (Kerben, Oberflächenrauhigkeit, Mittelspannung, etc.) erlaubt, die in den konventionellen Ansätzen mit vergleichsweise hoher Ungenauigkeit halbempirisch einbezogen werden. Der Beitrag stellt einen von den Autoren entwickelten bruchmechanischen Ansatz zur Ermittlung von Wöhlerkurven vor, der eine Reihe innovativer Merkmale wie die Anwendung der elastischplastischen Bruchmechanik auf kurze Risse, die Ermittlung der Ausgangsrissgröße aus Rissarrestbetrachtungen, die Beschreibung der transienten Entwicklung des Rissschließeffekts mit Hilfe zyklischer R-Kurven (Risslängenabhängigkeit des Schwellenwertes von der Risstiefe), die theoretische Erfassung von Mehrfachrisswachstum bei Lastniveaus oberhalb der Dauerfestigkeit und statistische Aspekte umfasst. Das diskutierte Beispiel ist eine Schweißverbindung (Stumpfnaht) und wurde im Rahmen des laufenden Cluster-Projektes IBESS (Integrale bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen) generiert. T2 - 42. Tagung des DVM-Arbeitskreises Betriebsfestigkeit CY - Dresden, Germany DA - 07.10.2015 KW - Bruchmechanik KW - Schwingfestigkeit KW - Zyklische R-Kurve PY - 2015 SN - 1616-5144 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 142 SP - 285 EP - 296 CY - Berlin AN - OPUS4-35299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Klinger, Christian A1 - Clegg, R. T1 - Fracture mechanics as a tool in failure analysis - Prospects and limitations N2 - Although fatigue crack propagation and fracture cause a large part of failure events in industrial practice, fracture mechanics in failure analysis seems to be still a side issue. Starting from an introduction into important basic questions of failure analysis and fracture mechanics, the authors specify what kind of questions in failure analysis can be effectively solved by fracture mechanics (and which can't). They illustrate their discussion with a number of 13 case studies from the literature. Much more pronounced than in the design stage the benefit of fracture mechanics in failure analysis depends on its accuracy. This is limited by both, intrinsic factors of the method and the availability and quality of the input information. The authors discuss the various aspects and provide the reader with some background information which, as they believe, will be helpful for better understanding the prospects and limitations of fracture mechanics in failure analysis and the conditions of its application. KW - Failure analysis KW - Fracture mechanics KW - Fatigue KW - Root cause KW - Accompanying measures PY - 2015 DO - https://doi.org/10.1016/j.engfailanal.2015.07.001 SN - 1350-6307 SN - 1873-1961 VL - 55 SP - 376 EP - 410 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-33839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Hübner, P. T1 - Fracture mechanics assessment of welded structures. Method for S-N curve determination T2 - Symposium on recent trends in fracture and damage mechanics CY - Freiberg DA - 2015-09-24 PY - 2015 AN - OPUS4-33848 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Kiyak, Yusuf A1 - Madia, Mauro A1 - Burgold, Andreas A1 - Riedel, Gernot T1 - Reference loads for plates with semi-elliptical surface cracks subjected to tension and bending for application within R6 type flaw assessment N2 - Two of the authors of the present paper proposed a definition of a reference load F0 which can be used as an alternative option to the common limit load for cases where the definition of the latter might be problematic in the frame of flaw assessment procedures such as R6, BS 7910, SINTAP or FITNET. The reference load is defined as that load at which the ligament yielding parameter Lr approaches one. F0, in general, varies along the crack front. It has to be obtained by finite element analyses but the results can be approximated by analytical expressions. In a previous study of the authors such a solution was presented for tension loaded plates with semi-elliptical surface cracks. In the present paper it is extended to pure bending and to combined bending and tension. KW - Flaw assessment KW - R6 procedure KW - BS 7910 KW - SINTAP KW - FITNET KW - Limit load KW - Reference load PY - 2013 DO - https://doi.org/10.1016/j.engfracmech.2012.11.017 SN - 0013-7944 SN - 1873-7315 VL - 99 SP - 132 EP - 140 PB - Elsevier Science CY - Kidlington AN - OPUS4-30416 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. T1 - A model for the determination of the fatigue life in technical alloys containing large and small defects N2 - The determination of the fatigue life in technical alloys containing large and small defects must rely on a propagation model which accounts for short and long crack growth. Recently an analytical model which incorporates propagation in the short crack regime and plastic correction for the crack driving force has been presented by two of the authors. This work is intended to show further validation of the model, taking into account data sets for different materials with different testing conditions. Despite the assumptions about missing parameters, the value of which had to be taken from the literature, the predictions showed a fairly good approximation of the fatigue lives. A possible interpretation of the results in terms of multiple crack initiation and propagation at higher loads is proposed. T2 - EFC20 - 20th European conference on fracture CY - Trondheim, Norway DA - 30.06.2014 KW - Fatigue strength KW - Crack propagation KW - Short cracks PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-311961 DO - https://doi.org/10.1016/j.mspro.2014.06.082 SN - 2211-8128 VL - 3 SP - 493 EP - 498 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-31196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Klinger, Christian A1 - Clegg, R. T1 - Fracture mechanics as a tool in failure analysis T2 - ICEFA IV CY - Lisbon, Portugal DA - 2014-07-06 PY - 2014 AN - OPUS4-31122 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Arafah, D. T1 - Reference load solutions for plates with semi-elliptical surface cracks T2 - ECF 20 - European Conference on Fracture CY - Trondheim, Norway DA - 2014-06-30 PY - 2014 AN - OPUS4-31123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Zerbst, Uwe ED - Zerbst, Uwe T1 - Analytische bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen (IBESS-A3) N2 - Ziel des DFG-AiF-Forschungsclusters IBESS war die Entwicklung einer Methodik zur bruchmechanischen Ermittlung von Wöhlerkurven in Schweißverbindungen. Dem vorliegenden Teilprojekt A3 kamen dabei zwei Aufgaben zu: die Entwicklung einer analytischen bruchmechanischen Methodik und die Koordinierung des insgesamt acht Partner umfassenden Clusters. Dieser Bericht fasst die Ergebnisse der erstgenannten Aufgabe zusammen. Die bruchmechanische Methode ist durch folgende Aspekte charakterisiert. (a) Sie beschreibt sowohl Kurz- als auch Langrisswachstum. Ersteres umfasst mechanisch und physikalisch kurze Risse. Mechanisch kurze Risse weisen Abmessungen in der Größenordnung der plastischen Zone auf, weshalb sie zwar bruchmechanisch, nicht jedoch auf der Basis des linear-elastischen K-Konzepts charakterisiert werden können. Im Projekt wurde entsprechend eine Methode zur Bestimmung eines „plastizitätskorrigierten“ zyklischen K-Faktors entwickelt, die auf dem zyklischen J-Integral beruht. Physikalisch kurz bedeutet, dass die Rissschließeffekte im Ausgangsstadium der Rissentwicklung zunächst noch nicht vorhanden sind, dann jedoch graduell aufgebaut werden, bis sie mit Erreichen des Langrissstadiums eine risstiefenunabhängig konstante Größe erreichen. Beschrieben wird dieser Effekt durch die Anwendung der sogenannten zyklischen R-Kurve, der Funktion des Schwellenwerts gegen Rissausbreitung von der Risstiefe. Mittels Rissarrestbetrachtungen des kurzen Risses werden (b) die Ausgangsrissgröße für die weitere Bruchmechanikanalyse und (c) die für N = 107 definierte Dauerfestigkeit der Bauteile bestimmt. Die Analyse erfolgt (d) statistisch, Schwankungen der lokalen Nahtgeometrie entlang des Nahtübergangs über ein Modell äquidistanter Abschnitte einbezogen werden. (e) Eigenspannungen werden sowohl im unbehandelten Schweißzustand als auch nach zyklischer Belastung berücksichtigt. Das Modell wird an insgesamt 33 Wöhlerkurven validiert, die an drei Schweißverbindungsformen (Stumpfstoß, Kreuzstoß, Längssteife) mit je zwei unterschiedlichen Ausführungen, zwei Werkstoffen (S355NL und S960QL), sowie im spannungsarmgeglühten und ungeglühten Zustand experimentell ermittelt wurden. KW - Bruchmechanik KW - Schweißverbindungen KW - Schwingfestigkeit PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-359891 SP - Römisch I EP - 182 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Schork, Benjamin T1 - Fracture mechanics based determination of the fatigue strength of weldments N2 - A fracture mechanics model which shall be applied to the fatigue strength determination of weldments has to focus on various aspects such as: (a) the description of mechanical and physical short fatigue crack extension which is characterised by yielding conditions which do not permit the application of the common ΔK concept and by the gradual build-up of the crack closure effect, (b) a consistent methodology for determining the initial crack size, (c) based on this, the determination of a fatigue limit, (d) the treatment of multiple crack propagation at load levels above this limit, (e) the variation of the local geometry along the weld toe, and (f) statistical effects.The paper gives alimited overview of the work the authors did in this field during the last years within the German project cluster IBESS. A model is presented and briefly discussed which covers the questions above. T2 - XV Portugese Conference on Fracture CY - Lissabon, Portugal DA - 10.02.2016 KW - Weldments KW - fatigue strength KW - fracture mechanics KW - fatigue crack propagation PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-361571 UR - http://www.sciencedirect.com/science/article/pii/S2452321616000044 DO - https://doi.org/doi:10.1016/j.prostr.2016.02.003 VL - 2016/1 SP - 10 EP - 17 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-36157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Eufinger, J. A1 - Bruder, T. T1 - Bruchmechanisches Modell zur Ermittlung der Schwingfestigkeit von geschweißten und nichtgeschweißten Proben N2 - Ermüdungsrisse gehen in technischen Materialien in der Regel von Werkstoffdefekten auf oder nahe der Oberfläche aus. Bei Schweißverbindungen können Schweißnahtdefekte, z. B. oberflächennahe Schlackeneinschlüsse die Risseinleitungsphase erheblich verkürzen, so dass der Hauptteil der Lebensdauer auf die Phase der Kurzriss- und zu geringerem Anteil auf die Langrissausbreitung entfällt. Bei nichtgeschweißten Bauteilen aus technischen Werkstoffen starten Ermüdungsrisse häufig an Einschlüssen, oberflächennahen Poren oder anderen Ungänzen. Einerseits ermöglicht dies prinzipiell die Anwendung bruchmechanischer Methoden zur Ermittlung der Schwingfestigkeit, andererseits müssen die Methoden in der Lage sein, spezielle Aspekte des Kurzrisswachstums wie den graduellen Aufbau des Rissschließeffekts und die lokale Rissspitzenplastizität zu erfassen. Im Beitrag werden ein geeignetes analytisches Modell sowie erste Validierungen an Proben aus verschiedenen Aluminiumlegierungen vorgestellt. Der abschließende Teil des Beitrags geht auf Besonderheiten von Schweißverbindungen (Schweißnahtdefekte, Eigenspannungen etc.) im Kontext des vorgestellten Modells ein. Eine Erweiterung des Modells für Schweißverbindungen aus Stahl wird im Rahmen eines kürzlich gestarteten DFG-AiF-Clusterprojekts erfolgen. PY - 2013 UR - http://www.hanser-elibrary.com/doi/pdf/10.3139/120.110465 DO - https://doi.org/10.3139/120.110465 SN - 0025-5300 VL - 55 IS - 7-8 SP - 511 EP - 519 PB - Hanser CY - München AN - OPUS4-30323 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe ED - Baumgartner, J. ED - Melz, T. T1 - Assessment of welded joints by fracture mechanics IBESS - the development of a procedure N2 - The idea to determine the fatigue strength of weldments by means fracture mechanics was originally based on the empirical observation that the major portion of the fatigue life in weldments is frequently spent in crack propagation. The present paper gives a brief overview on the basic principles of fracture mechanics-based determination of fatigue strength and on special features which have to be considered for weldments. Based on this information, the ongoing research project IBESS is introduced and briefly reviewed. T2 - SoSDiD - 4th Symposium on structural durability in Darmstadt CY - Darmstadt, Germany DA - 2014-05-14 KW - Fracture mechanics KW - Fatigue strength KW - (Residual) lifetime KW - Weldments PY - 2014 SP - 49 EP - 66 PB - Fraunhofer Verlag AN - OPUS4-31321 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Klinger, Christian T1 - Anmerkungen zur Auslegung und zum sicheren Betrieb von Radsatzwellen aus der Sicht von Betriebsfestigkeit und Bruchmechanik N2 - Die Sicherheit von Radsatzwellen beruht gegenwärtig auf zwei Säulen: der Schwingfestigkeitsauslegung und periodischen Inspektionen. Ausgehend von einem Schadensfall, der gebrochenen ICE 3-Welle von Köln, 2008, werden ausgewählte Aspekte dieser beiden Säulen diskutiert und Vorschläge zur weiteren Verbesserung gemacht. Diese betreffen u. a. Fragen einer Betriebszeitbegrenzung, Veränderungen der Schwingfestigkeit während des Betriebs infolge von Korrosion und Steinschlag, den Einfluss von Korrosion auf Schwingrissinitiierung und -fortschritt, den potenziellen Einfluss nichtmetallischer Einschlüsse auf die Schwingfestigkeit, die Möglichkeiten, sie im Rahmen der Qualitätssicherung zu detektieren, sowie Fragen der Bruchmechanik und der Zuverlässigkeit zerstörungsfreier Schwingriss-Prüfverfahren im Rahmen eines Konzepts regelmäßiger Inspektionen. KW - Radsatzwellen KW - Schwingfestigkeit KW - Sichere Lebensdauer KW - Schadenstoleranz KW - Zerstörungsfreie Inspektion KW - Korrosion KW - Steinschlag KW - Nichtmetallische Einschlüsse PY - 2014 DO - https://doi.org/10.3139/120.110593 SN - 0025-5300 VL - 56 IS - 7-8 SP - 528 EP - 534 PB - Hanser CY - München AN - OPUS4-31355 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Beier, H.T. T1 - A model for fracture mechanics based prediction of the fatigue strength: Further validation and limitations N2 - Recently two of the authors of the present paper proposed a model for a fracture mechanics based prediction of the S–N characteristics of metallic components with large microstructural defects and supported this by a validation exercise on tensile plates made of an aluminium alloy AL5380 H321. Here the authors extend the study using a number of further data sets from the literature for which data were available at different R ratios. These data include two aluminium alloys, Al 2024-T3 and Al 7075-T6, and a ductile cast iron, EN-GJS- 400-18-LT. Despite of necessary assumptions for the compensation of partially missing input information the results were fairly reasonable with the exception of one data set. The authors identify high applied stress levels in combination with potential multiple crack initiation as the probable root of the problem and propose a scheme how the model can be extended for taking into account crack initiation. KW - Fatigue strength KW - S–N curve KW - Fracture mechanics KW - Crack propagation KW - Short cracks PY - 2014 UR - http://ac.els-cdn.com/S0013794413003901/1-s2.0-S0013794413003901-main.pdf?_tid=1403b676-b8a0-11e3-9087-00000aab0f26&acdnat=1396248522_d8c91133aa860e68196d9325c22ce651 DO - https://doi.org/10.1016/j.engfracmech.2013.12.005 SN - 0013-7944 SN - 1873-7315 SP - 1 EP - 17 PB - Elsevier Science CY - Kidlington AN - OPUS4-30452 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Arafah, D. A1 - Zerbst, Uwe T1 - Reference load solutions for plates with semi-elliptical surface cracks subjected to biaxial tensile loading N2 - The yield or limit load is a key parameter with respect to the accuracy of flaw assessment based on R6 type procedures such as the R6 routine, the SINTAP and FITNET method, the standard BS 7910 and others. In a number of previous papers two of the present authors proposed the use of a reference load instead of the common limit load, which not only provided more exact fracture mechanics predictions, but showed also a wider and more general application range than the conventional parameter. Here the method has been extended to biaxial tensile loading and it has been successfully validated by a thorough comparison with finite element results and alternative solutions available in the literature. KW - Flaw assessment KW - R6 procedure KW - Limit load KW - Reference load KW - Biaxial tensile loading PY - 2014 DO - https://doi.org/10.1016/j.ijpvp.2014.02.004 SN - 0308-0161 VL - 119 SP - 19 EP - 28 PB - Applied Science Publ. Ltd. CY - Barking AN - OPUS4-31429 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - The Fatigue Crack Propagation threshold as a design criterion - actual developments and open issues T2 - ESIS TC1/TC3 workshop on "The fatigue crack propagation threshold as a design criterion" CY - Poitiers, France DA - 2014-11-04 PY - 2014 AN - OPUS4-31686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Schödel, M. A1 - Beier, H.T. T1 - Parameters affecting the damage tolerance behaviour of railway axles N2 - The paper provides a discussion on damage tolerance options applied to railway axles and factors influencing the residual lifetime as well as the required inspection interval. These comprise material properties such as the scatter of the da/dN–ΔK curve, the fatigue crack propagation threshold ΔKth and the toughness of the material. Parameters affecting axle loading such as the press fit, rotating bending, load history and mixed crack opening modes are discussed. Finally the influence of the initial crack geometry on residual lifetime is simulated. KW - Railway axles KW - Damage tolerance KW - Fatigue crack propagation PY - 2011 DO - https://doi.org/10.1016/j.engfracmech.2010.03.013 SN - 0013-7944 SN - 1873-7315 VL - 78 IS - 5 SP - 793 EP - 809 PB - Elsevier Science CY - Kidlington AN - OPUS4-22491 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Ainsworth, R. A. A1 - Madia, Mauro T1 - Grenzlast oder Referenzlast? - Vorschlag für eine hybride Vorgehensweise bei der elastisch-plastischen Bauteilbewertung T2 - 42. Tagung des DVM-Arbeitskreises Bruchvorgänge - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Paderborn, Deutschland DA - 2010-02-23 KW - Bruchmechanische Bauteilbewertung KW - EPRI-Methode KW - Referenzspannungsmethode KW - R6-Routine KW - SINTAP KW - FITNET KW - FKM-Richtlinie KW - Grenzlast KW - Referenzlast PY - 2010 SP - 183 EP - 194 AN - OPUS4-22493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Beretta, S. A1 - Schödel, M. A1 - Zerbst, Uwe A1 - Luke, M. A1 - Varfolomeyev, I. T1 - Stress intensity factor solutions for cracks in railway axles N2 - The aim of this paper is a collection of stress intensity factor solutions for cracks in railway axle geometries which the authors of the present special issue developed and/or used for damage tolerance analyses. These solutions comprise closed form analytical as well as tabled geometry functions and they refer to solid as well as hollow axles and various crack sites such as the T- and V-notch and the axle body. KW - Railway axles KW - Stress intensity factor PY - 2011 DO - https://doi.org/10.1016/j.engfracmech.2010.03.019 SN - 0013-7944 SN - 1873-7315 VL - 78 IS - 5 SP - 764 EP - 792 PB - Elsevier Science CY - Kidlington AN - OPUS4-22495 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Beretta, S. T1 - Failure and damage tolerance aspects of railway components N2 - Railway structures such as rails and axles are safety relevant components since any failure includes the risk of catastrophic derailment. This paper gives a brief overview on the most important potential failure scenarios driven by fatigue crack initiation and propagation and discusses the effects of important influencing factors such as vehicle weight and speed, track quality and environmental conditions. The present paper summarizes earlier work of the authors in this field. KW - Railway rails KW - Railway axles KW - Fatigue crack propagation KW - Damage tolerance KW - Fracture mechanics PY - 2011 DO - https://doi.org/10.1016/j.engfailanal.2010.06.001 SN - 1350-6307 SN - 1873-1961 VL - 18 IS - 2 SP - 534 EP - 542 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-22639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Kiyak, Yusuf A1 - Zerbst, Uwe T1 - Extended parametric equations for weld toe stress concentration factors and through-thickness stress distributions in butt-welded plates subject to tensile and bending loading N2 - Based on a large set of 2D finite element analyses, parametric equations for weld toe stress concentration factors and through-thickness stress profiles are provided for butt-welded plates. These cover Single-Vand Double-V joints subject to tensile and bending loading. Compared to the most widespread solutions in the literature, which have also been tested against the finite element data in this work, the application range is extended particularly with respect to the weld toe radius(0.1≤ρ≤4 mm)andangle(10 °≤α≤60 °). Furthermore, two values of excess weld metal are considered (h=0.75;2.5mm). The analyses are performed for a plate thickness of 10 mm. Besides the extended validity range, the proposed equations show also an improved accuracy compared to the existing solutions. KW - Butt welds KW - Weld toes KW - Stress analysis KW - Structures PY - 2016 DO - https://doi.org/10.1007/s40194-016-0377-x VL - 60 IS - 6 SP - 1247 EP - 1259 AN - OPUS4-37959 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - S., Romano A1 - D., Manenti A1 - S., Beretta T1 - Semi-probabilistic method for residual lifetime of aluminothermic welded rails with foot cracks N2 - One of the most frequent and dangerous failure modes in continuous welded rails is fatigue crack Propagation terminated by brittle fracture. Due to the brittleness of the weld material and HAZ and the scatter in its mechanical properties, a statistical approach is necessary. The paper deals with surface cracks at the foot base of aluminothermic welded rails, developing a probabilistic methodology for determining the day by day prospective failure probability. The investigations presented here comprise weld material characterization, simulation of fatigue crack propagation and finally the determination of the failure probability using the Monte Carlo method. The effect of various parameters, such as axle weight, Initial crack size, residual stresses, fatigue crack propagation threshold and date of inspection were analyzed. The results show that, independent of the date of the last inspection, almost any failure event happens in wintertime. This is in accordance with practical experience. However, from the proposed analysis it is evident that the main parameter controlling rail fracture is not only the minimum local temperature, but the temperature range over the whole year. Finally, the results are compared to the standard rail classification method. KW - Railway rails KW - Foot crack KW - Fatigue crack KW - Failure probability KW - Residual lifetime PY - 2016 DO - https://doi.org/10.1016/j.tafmec.2016.05.002 SN - 0167-8442 VL - 85 IS - Part B SP - 398 EP - 411 PB - Elsevier AN - OPUS4-38156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Fracture mechanics in failure analysis N2 - Starting from an introduction into important Basic questions of failure analysis and fracture mechanics, the author specifies what kind of questions in failure analysis can be effectively solved by fracture mechanics (and which can't). He illustrates his discussion with a number of case studies. Much more pronounced than in the design stage the benefit of fracture mechanics in failure analysis depends on ist accuracy. This is limited by both, intrinsic factors of the method and the availability and quality of the input information. The author discusses the various aspects and provides the participants with background information helpful for better understanding the prospects and limitations of fracture mechanics in failure analysis and the conditions of its application. T2 - ICEFA VII - International Conference of Engineering Failure Analysis CY - Leipzig, Germany DA - 03.07.2016 KW - Failure analysis PY - 2016 AN - OPUS4-38166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Schadensentwicklung und Schadenstoleranz von SLM-gefertigten Werkstoffen N2 - Unterschiedliche Werkstoffeigenschaften reagieren auf jeweils spezifische Weise auf Gittertyp, Gefüge und Defekte. Für die schadenstolerante Betrachtung von Werkstoff und Bauteil ist das Verständnis dieser Zusammenhange essentiell. Der Beitrag gibt mit Hinblick auf additiv gefertigte metallische Bauteile (Selective Laser Melting) einen kurzen, keineswegs vollständigen Überblick über Faktoren, die die Steifigkeit, Festigkeit, Duktilität, Zähigkeit, Ermüdungsrissausbreitung und Schwingfestigkeit beeinflussen. Es wird aufgezeigt, wie die bruchmechanische Betrachtung zur Quantifizierung der zusammenhänge beitragen kann. T2 - 1. Tagung des Arbeitskreises Additiv gefertigte Bauteile und Strukturen CY - Berlin, Germany DA - 02.11.2016 KW - Selective Laser Melting (SLM) KW - Werkstoffeigenschaften KW - Schadenstoleranz KW - Bruchmechanik PY - 2016 SN - 2509-8772 VL - Bericht 401 SP - 187 EP - 212 AN - OPUS4-38420 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Heckel, Thomas A1 - Carboni, M. T1 - Non-destructive testing and fracture mechanics - A short discussion N2 - A discussion is provided on the relation between non-destructive testing (NDT) and fracture mechanics. The basic tasks behind this are to guarantee the safety of a component at a potential hazard loading event, to specify inspection intervals or, alternatively, of demands on NDT for a fixed inspection regime, to plan accompanying measures for cases of temporary continued operation of structures in which cracks have been detected, and, finally, fatigue strength considerations which take into account initial defects. T2 - 42nd Annual review of progress in quantitative nondestructive evaluation conference CY - Minneapolis, Minnesota, USA DA - 2015-07-26 KW - Zerstörungsfreie Prüfung KW - Schwingfestigkeit KW - Schadenstoleranz KW - Bruchmechanik KW - probability KW - damage tolerance KW - railway axles KW - inspection PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940614 SN - 0094-243X VL - 1706 SP - 150002-1 EP - 150002-5 PB - AIP Publishing CY - Melville, New York, USA AN - OPUS4-33866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro T1 - Der Schwellenwert DKth als Auslegekriterium. Aktuelle Entwicklungen und Fragestellungen. T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge CY - Freiberg DA - 2015-02-10 PY - 2015 AN - OPUS4-32351 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scolavino, L. A1 - Beretta, S. A1 - Madia, Mauro A1 - Zerbst, Uwe T1 - Critical speed of flawed rotors: global vs local approach N2 - The burst of a disc in rotating machinery can cause catastrophic damage of the equipment and, more importantly, it can represent a mortal threat to anyone in the sphere of influence of the event. In order to minimize the danger associated to a rotating component failure, burst testing is required by the authorities in order to set safety margins to the normal operating speeds. Moreover more accurate predicting tools are required for designing the components. This paper presents the results of a numerical and analytical study on the assessment of the crack driving force for discs containing surface flaws. The aim is to provide a simple, though reliable, tool in order to be able to calculate the possible dangerous in-service speed for a rotating component and, therefore, to set burst margins above the normal operating conditions of the equipment. An R6-like flaw assessment procedure is adopted considering different assumptions in the definition of the critical speed and the analytical predictions are compared with the results of elastic-plastic finite element analysis of disc. In particular, the validity and potentiality of the method is proved for surface flaws in different positions in the disc. T2 - ASME Turbo Expo 2014 - GT2014 CY - Düsseldorf, Germany DA - 16.06.2014 KW - Critical speed KW - Flawed rotors KW - Flaw assessment PY - 2014 SN - 978-0-7918-4576-9 DO - https://doi.org/10.1115/GT2014-26881 VL - 7A SP - 26881, 1 EP - 8 AN - OPUS4-32382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Statistische Aspekte der Bauteilbewertung T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge; Weiterbildungsseminar CY - Freiberg, Germany DA - 2015-02-09 PY - 2015 AN - OPUS4-32845 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. A1 - Schöne, Dieter T1 - Analytische Beschreibung von Rissarrest, Kurz- und Langrisswachstum in Schweißverbindungen N2 - Kernstück der angestrebten IBESS-Prozedur ist eine analytische Methode zur bruchmechanischen Beschreibung der Rissausbreitung unter Schwingbelastung. Da man es im Bereich der Schwingfestigkeit mit kurzen Rissen zu tun hat, auf die die etablierten Methoden der Langrissbruchmechanik nicht anwendbar sind, werden Lösungen entwickelt, die es erlauben, sowohl die rissnahen Plastizitätsverhältnisse als auch die mit wachsendem Riss graduell zunehmenden Rissschließeffekte quantitativ zu beschreiben. Unter Einbeziehung der sogenannten "zyklischen R-Kurve", deren experimentelle Methodik ebenfalls im Rahmen des Projekts weiterentwickelt wird, ist es zudem möglich, Ausgangsrissgrößen vorherzusagen, die auf Dauerfestigkeitsniveau gerade so noch arretieren würden. Dies erlaubt umgekehrt eine Abschätzung der Dauerfestigkeit an realen Bauteilen wie eben Schweißnähten sowie die statistisch basierte, analytische Vorhersage des Zeitfestigkeitsastes der Wöhlerkurve. Die im Modell berücksichtigten Parameter bzw. deren statistische Verteilung schließen Werkstoffdaten und die lokale Nahtgeometrie (Nachtübergangsradius, Nahtanstiegswinkel, Einbrandkerben oder Oberflächenrauhigkeit) ein. Im Vortrag wird das analytische Modell vorgestellt und vor dem Hintergrund der im IBESS-Cluster bereitgestellten experimentellen Information diskutiert. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 300 EP - 306 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34799 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schork, B. A1 - Zerbst, Uwe A1 - Kucharczyk, P. A1 - Bernhard, J. A1 - Kaffenberger, M. A1 - Baumgartner, J. A1 - Oechsner, M. T1 - Imperfektionen für die schwingbruchmechanische Bewertung von Schweißverbindungen N2 - Bruchmechanischen Bewertungsmethoden liegt stets eine tatsachlich vorhandene oder fiktive Anfangsrisslange zu Grunde. Schweißverbindungen sind mit strukturellen Imperfektionen wie beispielsweise lnhomogenitaten in der Mikrostruktur und den Werkstoffeigenschaften behaftet, welche auf der Werkstoffseite berücksichtigt werden können. Imperfektionen wie der Kantenversatz und der Nahtübergangsradius, die als außere geometrische Imperfektionen aufgefasst werden können, haben vor allem Auswirkungen auf den Spannungszustand und werden daher auf der Lastseite erfasst. Innere geometrische Imperfektionen wie Einschlüsse oder Poren, von welchen Risse initiieren und sich ausbreiten, können als Ausgangsrissgröße aufgefasst werden. Im Teilprojekt A1 des Forschungsclusters IBESS wurden außere geometrische Imperfektionen an Schweißverbindungen ermittelt und statistisch ausgewertet. Des Weiteren wurden Schweißverbindungen fraktografisch im Rasterelektronenmikroskop (REM) bezüglich innerer geometrischer Imperfektionen untersucht, jedoch konnten aufgrund der hohen Schweißgütekeine schadigungsrelevanten inneren Imperfektionen (Ausgangsdefekte) detektiert werden. Um dennoch eine Ausgangsrisskonfiguration zu bestimmen, wurden "Heat-Tinting" Versuche eingesetzt, mit denen auf der Bruchflache verschiedene Anrissstadien markiert werden können. Mit dem .Heat-Tinting" Verfahren können sehr kleine Anrisse detektiert und in Abhangigkeit von der Beanspruchung frühe Anrisskonfigurationen ermittelt werden. Des Weiteren haben Zerbst und Madia im Teilprojekt A3 ein Modell entwickelt, mit dem für den Grundwerkstoff mittels zyklischer R-Kurven eine Ausgangsrissgröße rechnerisch ermittelt werden kann. Unter Verwendung der Ergebnisse aus den Versuchen zur Ermittlung der Anrissstadien soll dieses Modell validiert werden, um auch für Schweißverbindungen Anwendung zu finden. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 271 EP - 277 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Beier, H.T. A1 - Nitschke-Pagel, T. T1 - IBESS: Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen - Eine Einführung N2 - Die Projektbezeichnung IBESS steht für .Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen". Ziel des von acht Partnern vorangetriebenen AiF-DFG-Forschungsclusters IBESS ist die Entwicklung eines Ansatzes zur bruchmechanischen Ermittlung der Schwingfestigkeit von Schweißverbindungen. Die Arbeiten umfassen grundlegende Untersuchungen zum Wachstum und Arrest kurzer Risse, zur Ausbildung und Beeinflussung von Schweißeigenspannungen unter zyklischer Last, zum Einfluss der lokalen Nahtgeometrie auf die Rissausbreitung, zum Mehrfachriss-Phänomen oberhalb des Dauerfestigkeitsniveaus sowie zum Koaleszenzverhalten benachbarter Risse. Die gewonnenen Erkenntnisse fließen in ein analytisches Modell zur Ermittlung der Schwingfestigkeit ein, das physikalisch begründete und mithin sehr viel individuellere Vorhersagen des Ermüdungsverhaltens von Schweißnähten ermöglichen soll, als das auf konventioneller Basis bislang möglich ist. Ein nicht geringer Teil der Aktivitäten des Clusters ist mit der Bereitstellung von Daten zur Validierung befasst. Diese wird auf verschiedenen Ebenen vorgenommen, von der Beschreibung des Wachstuns von Einzelrissen über ihr Zusammenwachsen bis hin zur kompletten Wöhlerkurve. Ziel dieses Vortrags ist ein kurzer Überblick über das IBESS-Gesamtprojekt, das dem Zuhörer eine Einordnung der im IBESS-Vortragsblock vorgestellten Einzelaktivitäten ermöglichen soll. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 265 EP - 271 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34801 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, P. A1 - Zerbst, Uwe ED - Hütter, G. ED - Zybell, L. T1 - Fracture mechanics assessment of welded components at static loading N2 - Special aspects of welded components such as geometrical imperfections, inhomogeneity, strength mismatch and welding residual stresses have to be taken into account in a fracture mechanics analysis since they affect the crack driving force in the component as weil as the fracture resistance of the material. The treatment of components subjected to static loading is based on methods such as the European SINT AP procedure, which has been validated in a nurober of case studies. In the present paper the influence of strength mismatch and residual stresses on the fracture resistance and the assessment of a component are discussed. T2 - International symposium 'Recent trends in fracture and damage mechanics' CY - Freiberg/Sachsen, Germany DA - 24.09.2015 KW - Fracture mechanics KW - Weldments PY - 2015 SN - 978-3-319-21466-5 SP - Part II, 61 EP - 86 PB - Springer AN - OPUS4-34758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Bruchmechanik: Konzepte, Kennwertermittlung, Bauteilbewertung. Kurzeinführung Betriebsfestigkeit T2 - TU Flensburg CY - Flensburg DA - 2015-08-31 PY - 2015 AN - OPUS4-33849 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro T1 - Der Schwellenwert DKth als Auslegekriterium. Aktuelle Entwicklungen und Fragestellungen N2 - Bei der Bestimmung der Restlebensdauer zyklisch beanspruchter Bauteile kommt dem Schwellenwert für Ermüdungsrissausbreitung, K111, oft entscheidende Bedeutung zu. Dabei ist seine Anwendung weniger gesichert als bislang angenommen. Der Vortrag diskutiert Fragen der experimentellen Ermittlung des Schwellenwertes sowie seiner Anwendung auf Bauteile. Auf beiden Gebieten haben sich in den letzten Jahren Probleme ergeben, die bestehendes Wissen teilweise wieder in Frage stellen oder modifizieren. Im Beitrag diskutiert werden der Einfluss unterschiedlicher Rissschließmechanismen auf K111, Konsequenzen, die sich daraus hinsichtlich der Ermittlung und Übertragung des Kennwertes ergeben, sowie die Effekte von Einflussgrößen wie Spannungsverhältnis und Rissgröße, aber auch des Werkstoffgefüges und der damit korrelierten mechanischen Eigenschaften. T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge und Bauteilsicherheit - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Freiberg, Sachsen, Germany DA - 10.02.2015 PY - 2015 SN - 1616-4687 SP - 305 EP - 321 AN - OPUS4-34621 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Ainsworth, R. A. A1 - Beier, H.T. A1 - Pisarski, H. A1 - Zhang, Z. L. A1 - Nikbin, K. A1 - Nitschke-Pagel, T. A1 - Münstermann, S. A1 - Kucharczyk, P. A1 - Klingbeil, Dietmar T1 - Review on fracture and crack propagation in weldments - A fracture mechanics perspective N2 - Welding is one of the most common methods in industrial practice for joining components. Its main advantages are high speed in manufacturing combined with low costs and, usually, a high degree of flexibility, integrity and reliability. Nevertheless, welding is a highly complex metallurgical process and, therefore, weldments are susceptible to material discontinuities, flaws and residual stresses which may lead to structural failure and life time reduction. As a consequence weldments are an important field of fracture mechanics methods although its application is more complex than for homogeneous or non-welded structures. The aim of the paper is to provide an overview on the current state of fracture mechanics application to weldments. It starts by discussing the specific features which any fracture mechanics analysis of weldments has to take into account. Then, the experimental determination of fracture toughness, fatigue crack propagation and tensile properties of weldments is addressed. Finally, the analytical determination of the crack driving force in components and structural integrity assessment approaches for weldments are presented. KW - Weldments KW - Fracture mechanics KW - Fracture toughness KW - Fatigue crack propagation KW - Residual stresses KW - Strength mismatch PY - 2014 DO - https://doi.org/10.1016/j.engfracmech.2014.05.012 SN - 0013-7944 SN - 1873-7315 VL - 132 SP - 200 EP - 276 PB - Elsevier Science CY - Kidlington AN - OPUS4-32819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Arafah, D. A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beretta, S. A1 - Cristea, M.E. T1 - Instability analysis of pressurized pipes with longitudinal surface cracks N2 - Recently three of the authors of this paper presented analytical solutions for reference loads of plate geometries with semi-elliptical surface cracks subjected to tension, bending, combined tension-bending and biaxial tension. These solutions were shown to provide more accurate crack driving force estimates than the conventional limit load solutions available in the literature, and the method behind them allowed for a wider application range. Within the present paper a methodology for the fracture analysis of thick-wall pressurized pipes using the R6 assessment method and considering both, biaxial and combined tension-bending loading is developed and validated. The analyses are carried out analytically, and the comparison between the predicted critical loads and experimental burst test failure loads shows satisfying agreement, this way demonstrating the potential of the proposed method. KW - Burst test KW - Pipes KW - R6 KW - Reference load KW - Biaxial loading KW - Tearing instability KW - Plastic collapse KW - Limit load PY - 2015 DO - https://doi.org/10.1016/j.ijpvp.2015.01.001 SN - 0308-0161 VL - 126-127 SP - 48 EP - 57 PB - Applied Science Publ. Ltd. CY - Barking AN - OPUS4-32820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Werkstoffverhalten unter zyklischer Belastung T2 - DVM-Fortbildungsseminar "Bruchmechanische Prüfverfahren" CY - Freiburg, Germany DA - 2015-03-17 PY - 2015 AN - OPUS4-32836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Anwendungsphilosophien der Bruchmechanik in der Bauteilbewertung T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge; Weiterbildungsseminar CY - Freiberg, Germany DA - 2015-02-09 PY - 2015 AN - OPUS4-32840 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Rissspitzenbeanspruchung bei linear elastischem und elastisch-plastischem Deformationsverhalten. Praktische Ermittlung T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge; Weiterbildungsseminar CY - Freiberg, Germany DA - 2015-02-09 PY - 2015 AN - OPUS4-32842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Bauteilbewertung gegen Bruch. Demonstrationsbeispiele Druckbehälter T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge; Weiterbildungsseminar CY - Freiberg, Germany DA - 2015-02-09 PY - 2015 AN - OPUS4-32843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Primär- und Sekundärspannungen in der Bruchmechanik-Analyse T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge; Weiterbildungsseminar CY - Freiberg, Germany DA - 2015-02-09 PY - 2015 AN - OPUS4-32844 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Beier, T. T1 - Model for fracture mechanics based prediction of the fatigue strength of engineering alloys containing microscopical initial defects T2 - 2nd International Conference on Fatigue Design and Materials Defects (FDMD II) CY - Paris (Frankreich) DA - 2014-06-11 PY - 2014 AN - OPUS4-33237 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Assessment of welded joints by fracture mechanics. IBESS - Delevopment of a procedure N2 - The idea to determine the fatigue strength of weldments by means fractuie mechanics was originally based on the empirical observation that the major portion of the fatigue life in weldments is frequently spent in crack propagation. The present paper gives a brief OverView on the basic principles of fracture mechanics-based determination of fatigue strength and on special features which have to be considered for weldments. Based on this Information, the ongoing research project IBESS is introduced and briefly reviewed. T2 - 4th Symposium on Structural Durability CY - Darmstadt DA - 14.05.2014 PY - 2014 AN - OPUS4-33239 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schöne, Dieter A1 - Zerbst, Uwe A1 - Madia, Mauro T1 - Experimentelle Ermittlung des Schwellenwertes DeltaKth mittels unterschiedlicher Methoden und für verschiedene Spannungsverhältnisse N2 - ln den letzten Jahren hat sich gezeigt, dass die Ermittlung des Schwellenwertes DeltaKth nach den bestehenden Standardvorschriften für verschiedene Materialien zu nichtkonservativen Werten führt. Das ergibt sich im Vergleich mit Schwellenwerten, die man mit Anrissen erhält, die hinsichtlich der Ober- und der Unterlast komplett im Druckbereich erzeugt wurden. Dort, wo die Diskrepanz auftritt, verstärkt sie sich mit abnehmendem Spannungsverhältnis. ln der vorliegenden Studie wurden an einem mittel- und einem hochfesten Stahl bei unterschiedlichen Spannungsverhältnissen Schwellenwerte bestimmt. Anwendung fanden die konventionelle Lastabsenkungsmethode nach ASTM-Standard und ein Verfahren, bei dem der Langrissscbwellenwert als Endpunkt der sogenannten Zyklischen R-Kurve erhalten wird. Dieses folgt im Wesentlichen der von Pippan et al. entwickelten Methode, ergänzt diese jedoch durch eine eigene Verfahrensvariante. T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge und Bauteilsicherheit - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Freiberg, Germany DA - 10.02.2015 KW - Ermüdungsrissausbreitung KW - Schwellenwert KW - Lastabsenkung KW - Druckanschwingen KW - Zyklische R-Kurve KW - Fatigue crack propagation KW - Threshold KW - Load decreasing KW - Compression pre-cracking KW - Cyclic R curve PY - 2015 SN - 1616-4687 SP - 269 EP - 283 AN - OPUS4-32569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Madia, Mauro T1 - Fracture mechanics based assessment of the fatigue strength: approach for the determination of the initial crack size N2 - In a number of previous papers, the authors have proposed a model for fracture mechanics based prediction of the S-N characteristics of metallic components with large microstructural defects. Here, an extension to materials that do not show large defects onto the fracture surfaces is provided. In such cases, an approach based on a so-called cyclic R-curve analysis is proposed for the determination of the initial flaw size, which has to be used in the calculation of fatigue crack propagation. The principle is explained and demonstrated by a first application to a welded joint. KW - Fatigue strength KW - Weldments KW - Short cracks KW - Initial flaw size KW - Cyclic R-curve PY - 2015 DO - https://doi.org/10.1111/ffe.12288 SN - 1460-2695 SN - 0160-4112 SN - 8756-758X VL - 38 IS - 9 SP - 1066 EP - 1075 PB - Blackwell CY - Oxford AN - OPUS4-33838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - Schadensentwicklung und Schadenstoleranz von SLM-gefertigten Werkstoffen und Bauteilen N2 - Unterschiedliche Werkstoffeigenschaften reagieren auf jeweils spezifische Weise auf Gittertyp, Gefüge und Defekte. Für die schadenstolerante Betrachtung von Werkstoff und Bauteil ist das Verständnis dieser Zusammenhänge essentiell. Der Beitrag gibt mit Hinblick auf additiv gefertigte metallische Bauteile(Selective Laser Melting) einen kurzen, keineswegs vollständigen Überblick über Faktoren, die die Steifigkeit, Festigkeit, Duktilität, Zähigkeit, Ermüdungsrissausbreitung und Schwingfestigkeit beeinflussen. Es wird aufgezeigt, wie die bruchmechanische Betrachtung zur Quantifizierung der Zusammenhänge beitragen kann T2 - DVM - AK "Additiv gefertigte Bauteile und Strukturen" CY - Berlin, Germany DA - 02.11.2016 KW - Selective Laser Melting (SLM) KW - Werkstoffeigenschaften KW - Schadenstoleranz KW - Bruchmechanik PY - 2016 AN - OPUS4-38873 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe T1 - IBESS - an integral method for fracture mechanics-based determination of the fatigue strength of weldments N2 - The paper provides an overview on the results of a German cluster project on the use of fracture mechanics to the determination of the fatigue strength of weldments with fatigue cracks originating at the weld toes. The approach includes (a) a concept for short crack propagation for which the common K concept is not applicable and the crack closure effects are still being gradually build-up, (b) a method for determining fatigue life relevant initial crack sizes as they are needed in any fracture mechanics analysis and (c) multiple cracking and crack coalescence at load levels higher than the endurance limit. The analyses are stochastically performed. Both, the endurance limit as defined for 107 loading cycles and the finite life branch of the S-N curve are determined. Besides a brief introduction into the approach, a wide range of validation examples is presented. These comprise different weldment types (butt welds, cross joints and longitudinal stiffened plates), two steels of quite different strengths, different weld geometries due to different welding techniques (TIG, MAG), as-welded and stress relieved welds and different stress ratios varying from R = -1 to R = 0.5. T2 - Vortrag beim TWI (Welding Institute) CY - Great Abington, Cambridge, UK DA - 06.06.2017 KW - Fracture mechanics KW - S-N curve KW - Weldments PY - 2017 AN - OPUS4-43771 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Vormwald, M. T1 - Schwingfestigkeit und Bruchmechanik N2 - Um bruchmechanisch Schwingfestigkeiten ermitteln zu können, sind einige Voraussetzungen erforderlich: (a) Das Wachstum sowohl langer als auch mechanisch und physikalisch kurzer Risse muss adäquat beschrieben werden. Das erfordert die Anwendung elastisch plastischer Konzepte zur Beschreibung der zyklischen Rissspitzenbeanspruchung sowie die Modellierung des graduellen Aufbaus der Rissschließeffekte im Kurzrissbereich. (b) Es müssen physikalisch sinnvolle Ausgangsrissgrößen für die bruchmechanische Analyse bestimmt werden. (c) Bei Spannungen oberhalb der Dauerfestigkeit respektive der Versagensspannung bei 107 Lastwechseln muss gegebenenfalls Mehrfachrisswachstum berücksichtigt werden. Der Vortrag diskutiert diese Punkte und zeigt Lösungswege auf. T2 - 49. Tagung des Arbeitskreises "Bruchmechanik und Bauteilsicherheit" CY - Mittweida, Germany DA - 14.02.2017 KW - Schwingfestigkeit KW - Bruchmechanik KW - Ausgangsriss KW - Mehrfachriss PY - 2017 VL - 249 SP - 77 EP - 92 PB - DVM (Deutscher Verband für Materialforschung und -prüfung) CY - Berlin AN - OPUS4-39227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -