TY - CONF A1 - Musolff, André A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Gründer, Klaus-Peter T1 - Experimental testing of impact limiters for RAM packages under drop test conditions N2 - In context with new cask designs and their approval procedure, the experimental testing of impact limiters under drop test conditions becomes more and more important in order to assess the damage mechanics behaviour and safety margins for validation reasons. In recent years, various designs of impact limiters have been tested by the Federal Institute for Materials Research and Testing within specific component testing and particularly with regard to type B package design approval procedures. The paper focuses on the experimental realisation of impact limiter tests and presents implemented measurement techniques to determine the amount of deformation and to explain the impact behaviour by means of photogrammetric metrology and three-dimensional fringe projection method, high speed motion analysis and adjusted deceleration measurements. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Drop test KW - Impact limiters KW - RAM packages KW - Measurement methods PY - 2013 SP - 1 EP - 9 PB - Omnipress AN - OPUS4-31040 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Quercetti, Thomas A1 - Droste, Bernhard A1 - Müller, Karsten A1 - Gründer, Klaus-Peter T1 - Experimental investigation of RAM packages impact limiters - 14256 N2 - In context with new cask designs and their approval procedure the experimental testing of impact limiters under drop test conditions becomes more and more important in order to assess the damage mechanics behavior and safety margins for validation reasons. In recent years various designs of impact limiters have been tested by the Federal Institute for Materials Research and Testing (BAM) within specific component testing and particularly with regard to type B package design approval procedures. The paper focuses on the experimental realization of impact limiter tests and presents implemented measurement techniques to determine the amount of deformation and to explain the impact behavior by means of photogrammetric metrology and 3-d fringe projection method, high-speed motion analysis and adjusted deceleration measurements. T2 - WM2014 Conference CY - Phoenix, Arizona, USA DA - 02.03.2014 KW - Drop test KW - Impact limiters KW - RAM packages KW - Measurement methods PY - 2014 SN - 978-0-9836186-3-8 SP - Paper 14256, 1 EP - 10 AN - OPUS4-31050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Costabel, S. A1 - Hiller, Thomas A1 - Dlugosch, R. A1 - Kruschwitz, Sabine A1 - Müller Petke, M. T1 - Evaluation of single-sided nuclear magnetic resonance technology for usage in geosciences N2 - Because of its mobility and ability to investigate exposed surfaces, single-sided (SiS) nuclear magnetic resonance (NMR) technology enables new application fields in geosciences. To test and assess its corresponding potential, we compare longitudinal (T1) and transverse (T2) data measured by SiS NMR with those of conventional geoscientific laboratory NMR. We use reference sandstone samples covering a broad range of pore sizes. Our study demonstrates that the lower signal-to-noise ratio of SiS NMR data generally tends to slightly overestimated widths of relaxation time distributions and consequently pore size distributions. While SiS and conventional NMR produce very similar T1 relaxation data, unbiased SiS NMR results for T2 measurements can only be expected for fine material, i.e. clayey or silty sediments and soils with main relaxation times below 0.05s. This limit is given by the diffusion relaxation rate due to the gradient in the primary magnetic field associated with the SiS NMR. Above that limit, i.e. for coarse material, the relaxation data is strongly attenuated. If considering the diffusion relaxation time of 0.2 s in the numerical data inversion process, the information content >0.2s is blurred over a range larger than that of conventional NMR. However, our results show that principle range and magnitudes of the relaxation time distributions are reconstructed to some extent. Regarding these findings, SiS NMR can be helpful to solve geoscientific issues, e.g. to assess the hydro-mechanical properties of the walls of underground facilities or to provide local soil moisture data sets for calibrating indirect remote techniques on the regional scale. The greatest opportunity provided by the SiS NMR technology is the acquisition of profile relaxation data for rocks with significant bedding structures at the µm scale. With this unique feature, SiS NMR can support the understanding and modeling of hydraulic and diffusional anisotropy behavior of sedimentary rocks. KW - Single-sided NMR KW - Geosciences KW - Nuclear magnetic resonance PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-561676 DO - https://doi.org/10.1088/1361-6501/ac9800 SN - 0957-0233 VL - 34 IS - 1 SP - 1 EP - 13 PB - IOP Publishing AN - OPUS4-56167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Johnson, Mark A1 - Tait, Trevor A1 - Tso, Chi-Fung A1 - Izatt, Conrad ED - ASME, T1 - Drop testing of a container for the storage. transport and disposal of intermediate level waste N2 - Impact tests were performed, as part of a corresponding container’s substantiation, during design development of a shielded container. The container will be used for storage, transport, and disposal of intermediate level waste in the UK. The mechanical test program comprised a 9m free drop test onto an unyielding target in a container long lid edge down orientation at ambient conditions. Further, a 0,5m free drop test onto a punch target was performed. Here, the container was orientated with the lid downwards in a way that the punch, a mild steel bar, impacts a filter lid. The test specimen was instrumented with strain gauges and accelerometers for the drop tests. Transient strains at selected points of the inner and outer container walls, at the shielding lid, as well as at the lid bolts were measured during the container’s impact. Furthermore, decelerations of the container body, container lid, and the skip were measured. The complex geometrical changes of the container due to impact were determined by optical 3d- deformation measures using the projected fringes method in combination with multi-image photogrammetry. This paper summarizes the performance of the drop tests and various drop test results in context with the design development as well as aspects regarding the associated Finite Element (FE) analyses and post-test evaluation. KW - Drop testing KW - Container KW - Intermediate level waste PY - 2017 SN - 978-0-7918-5802-8 VL - 7 SP - Article UNSP V007T07A036, 1 EP - 7 CY - New York AN - OPUS4-44047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, Andre A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Bartholmai, Matthias T1 - Kinematic aspects of RAM packages drop tests N2 - BAM is the German Federal Institute for Materials Research and Testing and the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste. In context with safety assessment of RAM packages BAM performed numerous drop tests in the last decades. The tests were mostly accompanied by extensive and various measurement techniques especially by instrumented measurements with strain gages and accelerometers. The procedure of drop testing and the resulting measurement analysis are the main methods to evaluate the safety against mechanical test conditions. Measurement techniques are dedicated to answer questions in regard to the structural integrity of a RAM package, the mechanical behavior of the prototype as well as of its content under impact conditions. Test results like deceleration-time functions constitute a main basis for the validation of assumptions in the safety analysis and for the evaluation of numerical calculations. In this context the adequate selection of accelerometers and measurement systems for the performance of drop tests is important. Therefore it is not only necessary to find suitable positions for the accelerometers at the test specimens, but also to consider technical boundary conditions as e.g. temperature. T2 - 2018 WM Symposia CY - Phoenix, AZ, USA DA - 18.03.2018 KW - Drop KW - Test KW - Measurement KW - Analysis KW - Prototyp PY - 2018 SP - Paper 18149, 1 EP - 12 AN - OPUS4-44872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, Christina A1 - Heckel, Thomas A1 - Brömel, Philip A1 - Pavlovic, Mato A1 - Ronneteg, U. T1 - Attenuation dependent detectability at ultrasonic inspection of copper N2 - This report describes the progress in understanding and describing the detectability of the ultrasonic inspection technique developed by SKB for the inspection of copper tubes used for the final disposal of the Swedish spent nuclear fuel. In former research activities dedicated to the different parts of the canister, the probability of detection (POD) evaluation technique, as developed for thin aircraft components, was further developed for the application on complex hick-walled components. The result of this development was the introduction of a “multi-parameter” POD framework. In contrast to taking only the defect size into consideration (as for aircraft components) additional influencing factors, relevant for thick components, such as depth position, orientation and part geometry, were included. Furthermore, the variation of ultrasonic attenuation due to various material properties was included. PY - 2014 SP - ID 1411328, 1 EP - 54 AN - OPUS4-32522 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter A1 - Goedecke, Thomas A1 - Kadoke, Daniel A1 - Müller, Karsten A1 - Münzenberger, Sven A1 - Protz, Christian T1 - Prüfung von Gefahrgutumschließungen mit optischen 3D-Messverfahren N2 - Der Beitrag konzentriert sich auf bildgebende Messverfahren, die der dreidimensionalen Bestimmung mechanischer, geometrischer und kinematischer Parameter von Materialien und Bauteilen dienen. Das sind hier insbesondere die Mehrbildfotogrammetrie sowie die Stereomessverfahren, die auf folgenden physikalisch-optischen Grundlagen beruhen: die zeit- und raumveränderliche Projektion von Lichtstreifensystemen, die Bildkorrelation mittels Grauwertmustern und die Verfolgung kontrastreich applizierter Punkttargets. Letztendlich werden aus den gemessenen Punktkoordinaten unterschiedlicher Dichte und Belastungszustände die gewünschten 3D-Parameter abgeleitet. Hierzu gehören z. B. die Oberflächengestalt und deren Verformung, approximierte 3D-Geometrielemente, veränderliche 6DoF-Starrkörperorientierungen, Vektorverschiebungsfelder, Oberflächendehnung, Koordinaten-Zeit-Funktionen, Geschwindigkeit und Beschleunigung. Diese Kenngrößen sind beispielsweise für die Ermittlung mechanischer Werkstoffeigenschaften und -kennwerte bis hin zur Form- und Verformungsmessung von Bauteilen in gezielt quasi-statisch oder dynamisch beanspruchenden Prüfeinrichtungen wichtig. Vorteilhaft für die praktische Anwendung dieser Verfahren ist insbesondere, dass sie berührungslos arbeiten, kombiniert werden können und skalierbar sind z. B. hinsichtlich Messvolumen, Auflösung, Genauigkeit und Koordinatensystemen der zu bestimmenden 3D-Punktkoordinaten an Materialoberflächen bzw. Komponenten. Ausgehend von der Beschreibung der messtechnischen Prinzipien dieser Verfahren sollen zwei Anwendungsbeispiele aus dem Bereich der Gefahrgutbehäl-terprüfung im Rahmen von Bauartzulassungen und der normungsbegleitenden Mate-rialforschung den Stand in der Anwendungspraxis aufzeigen und einen Eindruck hinsichtlich der flexiblen Einsatzmöglichkeiten dieser optischen 3D-Verfahren verdeutlichen. T2 - 4. Fachseminar Optische Prüf- und Messverfahren CY - Hamburg, Germany DA - 17.03.2015 KW - 3D-Messverfahren KW - Verformung KW - Dehnung KW - Bremsbeschleunigung PY - 2015 SP - Vortrag 9, 1 EP - 10 AN - OPUS4-32808 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Krause, Martin A1 - Mayer, K. A1 - Ballier, G. A1 - Borchardt, Kerstin A1 - Chinta, P.K. A1 - Effner, Ute A1 - Milmann, Boris A1 - Müller, Sabine A1 - Nowak, Thomas Rudolf T1 - Hochgenaue Strukturerkennung von Holzbauteilen mit 3D-Ultraschall N2 - Inhalt ist die zerstörungsfreie Detailuntersuchung von Holzbauteilen mit einem dreidimensional abbildenden Ultraschall-Echoverfahren. Das neu entwickelte 3D-Verfahren berücksichtigt den anisotropen Aufbau des Holzes. Die Bildschnitte und Projektionen werden aus flächigen Ultraschallaufnahmen berechnet. Die Messungen erfolgen an Probekörpern sowie an Bauteilen aus der Praxis. In dem Forschungsvorhaben wird die für Holz neue 3D-Rekonstruktionsrechnung verwendet und mit dem Ziel weiterentwickelt, unter Berücksichtigung der anisotropen Struktur des Holzes eine dreidimensional aufgelöste Abbildung von Reflektoren im Inneren der Holzbauteile zu ermöglichen. Damit werden die bisher für Holzbauteile zur Verfügung stehenden Verfahren entscheidend ergänzt, weil nun eine hochgenaue dreidimensionale Abbildung erreichbar ist (Auflösung: 20 mm und besser). KW - Ultraschallecho-Verfahren KW - Holzbauteile KW - Abbildungsverfahren KW - Imaging PY - 2014 UR - https://www.irb.fraunhofer.de/bauforschung/baufolit/projekt/Hochgenaue-Strukturerkennung-von-Holzbauteilen-mit-3D-Ultraschall/20138035979 SN - 978-3-8167-9212-3 VL - 109 SP - 1 EP - 101 PB - Fraunhofer IRB Verl. CY - Stuttgart AN - OPUS4-32852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quercetti, Thomas A1 - Ballheimer, Viktor A1 - Droste, Bernhard A1 - Müller, Karsten T1 - Internal cask content collisions during drop test of transport casks for radioactive materials N2 - In transport casks for radioactive materials, significantly large axial and radial gaps between cask and internal content are often present because of certain specific geometrical dimensions of the content (e.g. spent fuel elements) or thermal reasons. The possibility of inner relative movement between content and cask will increase if the content is not fixed. During drop testing, these movements can lead to internal cask content collisions, causing significantly high loads on the cask components and the content itself. Especially in vertical drop test orientations onto a lid side of the cask, an internal collision induced by a delayed impact of the content onto the inner side of the lid can cause high stress peaks in the lid and the lid bolts with the risk of component failure as well as impairment of the leak tightness of the closure system. This paper reflects causes and effects of the phenomenon of internal impact on the basis of experimental results obtained from instrumented drop tests with transport casks and on the basis of analytical approaches. Furthermore, the paper concludes the importance of consideration of possible cask content collisions in the safety analysis of transport casks for radioactive materials under accident conditions of transport. KW - Drop test KW - Cask KW - Internal collision KW - Transport KW - Radioactive material PY - 2013 DO - https://doi.org/10.1179/1746510913Y.0000000032 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 24 IS - 2 SP - 75 EP - 82 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-31306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Quercetti, Thomas A1 - Musolff, André A1 - Droste, Bernhard T1 - Quality assurance requirements for mechanical test campaigns of packagings N2 - A management system based on international, national or other standards acceptable to the competent authority shall be established and implemented for all activities including design, manufacture, testing, documentation, use, maintenance, inspection in accordance with IAEA SSR-6. Hereby, quality assured testing and documentation can substantially contribute to the demonstration of package design compliance with the regulations. Nowadays, a drop test campaign within the approval process of packages for radioactive materials can be a very complex and extensive project including various test and measurement techniques. On this basis of procedures and documents the experimental tests of packages and containers are performed with quality proofed results and a high reliability. A complete traceability and direct transferability of package design test results can give particular importance to the type approval procedure. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Quality assurance KW - Packaging KW - Drop test PY - 2013 SP - Paper 181, 1 EP - 7 PB - Omnipress AN - OPUS4-30493 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Bartholmai, Matthias T1 - Impact Analysis of RAM Packages under Kinematic Aspects N2 - BAM is the German Federal Institute for Materials Research and Testing and the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste. In context with safety assessment of RAM packages BAM performed numerous drop tests in the last decades. The tests were mostly accompanied by extensive and various measurement techniques especially by instrumented measurements with strain gages and accelerometers. The procedure of drop testing and the resulting measurement analysis are the main methods to evaluate the safety against mechanical test conditions. Measurement techniques are dedicated to answer questions in regard to the structural integrity of a RAM package, the mechanical behavior of the prototype as well as of its content under impact conditions. Test results like deceleration-time functions constitute a main basis for the validation of assumptions in the safety analysis and for the evaluation of numerical calculations. In this context the adequate selection of accelerometers and measurement systems for the performance of drop tests is important. Therefore it is not only necessary to find suitable positions for the accelerometers at the test specimens, but also to consider technical boundary conditions as e.g. temperature. T2 - PATRAM 2016 CY - Kobe, Japan DA - 18.09.2016 KW - RAM packages KW - Drop test KW - Impact KW - Radioactive PY - 2016 UR - http://www.patram2016.org/ SP - Paper 1030, 1 AN - OPUS4-38859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Favre, A. A1 - Hilbert, F. A1 - Quercetti, Thomas A1 - Neumeyer, Tino A1 - Weingart, Barbara T1 - Prototype testing of a protective structural packaging for 30B cylinder N2 - Three drop test campaigns have been performed with DN 30 Protective Structural Packaging (PSP) developed by DAHER NUCLEAR TECHNOLOGIES GmbH for the transport of natural, enriched and reprocessed uranium hexafluoride (up to 5 wt%) in 30B cylinders. The mechanical prototype testing is intended to demonstrate that the package DN30 complies with regulatory requirements under normal and hypothetical accident conditions of transport (NCT, ACT) relevant to IF, AF and B(U)F packages, respectively. The paper includes the results of the latest test campaign carried out in 2015-2016 at the drop test facility of BAM, Germany with new full scale prototypes of the DN30 PSP and 30B cylinders. Repetition of drop test sequences became necessary after changing to Polyisocyanurate foam as shock absorbing material with variable foam densities. Furthermore, the mechanical behavior of the UF6 content of the 30B cylinder is now simulated by a mixture of cement and steel grid as modified surrogate material; instead of small steel balls. The behavior of this new content simulation is assumed to be more realistic with respect to the properties of real UF6. T2 - PATRAM 2016, 18th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Kobe, Japan DA - 18.09.2016 KW - Drop test KW - Packaging KW - Radioactive material KW - Uranium hexafluoride PY - 2016 SP - Paper 1018, 1 EP - 11 PB - INMM CY - Deerfield, Illinois, USA AN - OPUS4-37568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Musolff, Andre A1 - Nakagami, M. A1 - Komatsuki, S. A1 - Tamaki, H. A1 - Kishimoto, J. A1 - Fujisawa, K. A1 - Nishio, T. ED - Quercetti, Thomas T1 - Experimental testing of RAM packages within Japanese German projects N2 - In context with Japanese disposal and transport container safety assessment the German Federal Institute for Materials Research and Testing (Bundesanstalt für Materialforschung und -prüfung) per-formed extensive drop test series with prototypes of RAM packages in recent years. The paper presents two cooperative projects focused on project management, testing performance and experimental results. In the first project, a full-scale prototype of a package for transport and storage of spent fuel elements with a total mass of 127,000 kg and its reduced-scale model which was similar to the prototype in both geometry and design were drop tested in 9 m and 1 m puncture tests at various drop orientations under regulatory conditions. In context with a corresponding research project the test data was used in combination with numerical methods to investigate the phenomenon of internal cask- content collisions during drop tests. Here, technological gaps between basket or radioactive content and cask body or primary lid can be a reason for significant high dynamic loadings of cask components and its internals due to additional impact interactions in the cask cavity caused by inner relative movement between content and cask. Further investigations were carried out in the field of similarity mechanics comparing experimental drop test data of the full-scale prototype and reduced-scale model in regard to the transferability of package impact response from reduced-scale models to full-scale packages. In the second project, drop tests with a waste container for intermediate depth disposal were per-formed being contracted by Kobe Steel, Ltd. and a consortium of Japanese electric power plant com-panies. The drop test program comprised three single 8-m drop tests in a specimen’s corner edge orientation. For drop tests according to legal regulations for interim storage or final disposal it is often necessary to use a target which represents the real ground of the storage facility. In such cases the container hits directly onto a well-defined concrete slab on top of the IAEA target. Here, the directly impact target for the drop tests were concrete slabs manufactured in Japan and connected by mortar to the impact pad of the unyielding IAEA target. KW - Drop testing KW - Package PY - 2016 SP - Paper 1043, 1 EP - 13 CY - Kobe, Japan AN - OPUS4-37557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Musolff, André A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Gründer, Klaus-Peter T1 - Experimental testing of impact limiters for RAM packages under drop test conditions N2 - In context with new cask designs and their approval procedure, the experimental testing of impact limiters under drop test conditions becomes more and more important in order to assess the damage mechanics behaviour and safety margins for validation reasons. In recent years, various designs of impact limiters have been tested by the Federal Institute for Materials Research and Testing within specific component testing and particularly with regard to type B package design approval procedures. The paper focuses on the experimental realisation of impact limiter tests and presents implemented measurement techniques to determine the amount of deformation and to explain the impact behaviour by means of photogrammetric metrology and three-dimensional fringe projection method, high speed motion analysis and adjusted deceleration measurements. KW - Experimental KW - Drop test KW - Impact limiter KW - Close range photogrammetry PY - 2014 DO - https://doi.org/10.1179/1746510915Y.0000000003 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 25 IS - 3-4 SP - 133 EP - 138 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-33776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Schubert, Sven T1 - Comparison of experimental results from drop testing of a spent fuel package design using a full-scale prototype model and a reduced-scale model T2 - PATRAM 2007, 15th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Miami, Florida, USA DA - 2007-10-21 KW - Drop KW - Testing KW - Experiment KW - Prototype KW - Reduced-scale KW - Full-scale PY - 2007 SP - 1 EP - 8 PB - Institute of Nuclear Materials Management AN - OPUS4-18624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Droste, Bernhard A1 - Musolff, André A1 - Müller, Karsten A1 - Quercetti, Thomas T1 - Drop and fire testing of spent fuel and HLW transport casks at "BAM test site technical safety" - 10079 T2 - WM2010 - 36th Annual radioactive waste management symposium CY - Phoenix, Arizona, USA DA - 2010-03-07 KW - transport packages of radioactive materials KW - Safety KW - Mechanical tests KW - Thermal tests KW - Drop test facility KW - Fire test facilities KW - Numerical calculations PY - 2010 SN - 978-0-9828171-0-0 SP - 1 EP - 11 CY - Tempe, AZ, USA AN - OPUS4-21830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Schubert, Sven T1 - Comparison of experimental results from drop testing of spent fuel package design using full scale prototype model and reduced scale model N2 - This paper presents a comparison between full scale prototype and reduced scale model drop test data in regard to similarity mechanics. Together with a current BAM research project, the paper contributes to the further development of mechanical evaluation methods for safety assessment of RAM transport and storage packages including the transferability of package impact response from reduced scale models to full scale packages. KW - Full scale KW - Reduced scale KW - Drop testing KW - Similarity PY - 2008 DO - https://doi.org/10.1179/174651008X362575 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 19 IS - 4 SP - 197 EP - 202 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-20135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Karsten A1 - Quercetti, Thomas A1 - Melnik, Nauka A1 - Droste, Bernhard T1 - Impact target characterisation of BAM drop test facility N2 - BAM safety related research of containers for radioactive material focuses on advanced mechanical safety assessment methods for verification of the structural integrity and leak tightness under normal conditions of transport and hypothetical accident conditions during transport and storage. An essentially unyielding target with a rigid surface is required for impact tests performed for package approval according to IAEA regulations. In addition to specification of a target, e.g. with a combined mass more than 10 times that of the specimen for drop tests, unyielding target characteristics have been investigated with various package designs and different impact tests. The unyielding target of the BAM drop test facility, a reinforced concrete block together with an embedded and anchored mild steel plate, provides relatively large mass and stiffness with respect to the packages being tested. For monitoring reasons accelerometers and strain gauges are embedded in the concrete block of the foundation at several positions. Additionally, dynamic impact responses like vibrations and rigid body motion can be measured by seismic accelerometers. The mechanical characterisation of the target's rigidity is based on experimental results from various drop tests. Test containers with weights of 181 000 kg, 127 000 kg and 8010 kg hit the target with velocities up to 13·5 m s-1 in the horizontal and vertical drop positions. The rigidity of the impact target can be demonstrated with experimental results confirmed by analytical approaches. Some conclusions can be drawn about experimental testing as well as analytical calculations in order to compare impact effects. KW - Target KW - Unyielding KW - Impact KW - Drop test PY - 2009 DO - https://doi.org/10.1179/174651008X344449 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 19 IS - 4 SP - 217 EP - 221 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-20136 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Karsten A1 - Quercetti, Thomas A1 - Musolff, André T1 - Characterisation of shock-absorbing components under impact loading N2 - For validation of structural integrity under normal and hypothetical accident conditions during transport and storage of dangerous goods the Federal Institute for Materials Research and Testing (BAM) focuses its safety related scientific research on advanced mechanical safety assessment methods including simulation of high rate impact of model components and structures. An impact and crash test facility was recently developed for performing dynamic impact tests with component size specimen, or to crash specimens of impact limiter materials and structural components. The paper presents experimental techniques of BAM drop test machine and options of several measurement methods and advancements in order to characterize typical shock-absorbing materials under impact loading conditions. Instrumented drop weight tests are performed to complete materials data base and energy absorption of shock-absorbing materials as well as to implement materials and structural parameters into FEA of reference structures. T2 - 9th International conference on the mechanical and physical behaviour of materials under dynamic loading - DYMAT 2009 CY - Brussels, Belgium DA - 2009-09-07 PY - 2009 SN - 978-2-7598-0472-6 DO - https://doi.org/10.1051/dymat/2009081 VL - 1/2 SP - 569 EP - 574 PB - EDP Sciences AN - OPUS4-20242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Debatin, F. A1 - Thomas, A. A1 - Kelling, A. A1 - Hedin, N. A1 - Bacsik, Z. A1 - Senkovska, I. A1 - Kaskel, S. A1 - Junginger, M. A1 - Müller, H. A1 - Schilde, U. A1 - Jäger, Christian A1 - Friedrich, A. A1 - Holdt, H.-J. T1 - In situ synthesis of an imidazolate-4-amide-5-imidate ligand and formation of a microporous zinc-organic framework with H2-and CO2-storage ability KW - Metal-organic framework KW - Synthesis KW - XRD KW - FTIR KW - NMR KW - Gas sorption KW - Microporous materials KW - N,O ligands KW - Solvothermal synthesis PY - 2010 DO - https://doi.org/10.1002/anie.200906188 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 49 IS - 7 SP - 1258 EP - 1262 PB - Wiley-VCH CY - Weinheim AN - OPUS4-21132 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quercetti, Thomas A1 - Nakagami, M. A1 - Komatsuki, S. A1 - Musolff, André A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Fujisawa, K. T1 - Disposal container safety assessment - drop tests with 'Yoyushindo-disposal' waste container onto concrete target N2 - This paper presents technical details of the drop test performance as well as some experimental results of tests carried out with the Japanese 'Yoyushindo-Disposal' waste container for intermediate depth disposal. The drop test program comprised three single 8 m drop tests at the specimen's corner edge orientation onto a concrete slab. The slab was connected to the unyielding IAEA target of the BAM's 200 t drop test facility. The three tested specimens had masses between 20 000 and 28 000 kg depending on their content mass. The tests were accompanied by various metrology, such as strain and deceleration measurements, optical three-dimensional deformation methods, leak tightness testing and test installation for potential particle release measurements to collect a set of data for establishing a basis for safety assessment. KW - Drop test KW - Disposal container KW - Safety PY - 2010 DO - https://doi.org/10.1179/174650910X12681251630291 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 21 IS - 3 SP - 132 EP - 141 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-22613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Droste, Bernhard A1 - Quercetti, Thomas A1 - Müller, Karsten T1 - Durchführung experimenteller Fallprüfungen im Rahmen der mechanischen Bauartprüfung von Transportbehältern für radioaktive Stoffe T2 - Jahrestagung Kerntechnik 2010 CY - Berlin, Deutschland DA - 2010-05-04 PY - 2010 SP - 1 EP - 7 CY - Berlin AN - OPUS4-22770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -