TY - JOUR A1 - Scharf-Wildenhain, R. A1 - Engelking, Lorenz A1 - Hälsig, A. A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas A1 - Hensel, J. T1 - Effect of heat control on mechanical properties and residual stresses at the transition zone of component and substrate in hybrid DED‑arc manufacturing N2 - In hybrid additive manufacturing, components or semi-finished products manufactured by conventional primary forming are enhanced or modified by additive manufactured structures. However, systematic investigations focusing on the critical transition area between the specific properties of the substrate (like high-strength) and the additively manufactured component, made of specific filler material, are still lacking. The focus of the present study was to determine the influence of heat control on the Δt8/5 cooling time, the distortion, the mechanical properties, and the residual stresses in the transition area of hybrid-additive components. This contributed to the knowledge regarding the safe avoidance of cold cracking, excessive distortion, a reduction in yield stress, and the implementation of hybrid DED-arc manufacturing. The heat control was varied by means of heat input and working temperature such that the Δt8/5 cooling times corresponded to the recommended processing range. The heat input has a greater influence on the cooling time in the transition area than the working temperature. Working temperature and the total energy applied per layer have a significant effect on component distortion. The lowest working temperature of 100 °C in combination with the highest total energy per layer leads to significantly greater distortion compared to manufacturing with a high working temperature of 300 °C and low total energy per layer. In addition, the longitudinal residual compressive stresses in the sensitive transition area are reduced from − 500 MPa to approx. − 200 MPa by adjusting the working temperature from 100 to 300 °C. Such complex interactions must be clarified comprehensively to provide users with easily applicable processing recommendations and standard specifications for an economical hybrid additive manufacturing of components made, for example, of high-strength steels in the transition area. T2 - IIW Annual Assembly and International Conference CY - Rhodes Island, Greece DA - 07.07.2024 KW - Hybrid additive manufacturing KW - DED-arc KW - Heat control KW - High-strength metals KW - Residual stress PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630415 DO - https://doi.org/10.1007/s40194-025-02036-z SN - 1878-6669 SP - 1 EP - 15 PB - Springer AN - OPUS4-63041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Masoud Nia, Niloufar A1 - Nietzke, Jonathen A1 - Kannengiesser, Thomas T1 - Ti and Nb microalloying of HSLA steels and its effect on hydrogen diffusion and trapping N2 - Fine-grain, high-strength, low-alloy (HSLA) structural steels with yield strengths > 600 MPa are now the state of the art in construction applications such as mobile cranes and civil engineering. HSLA grades derive their strength from a combination of specific heat treatment and the underlying chemical composition. In this context, Ti or Nb are essential to obtain a fine-grained microstructure as well as the necessary carbides or nitrides for precipitation strengthening. In this context, the specific effect of Ti or Nb-rich compounds on hydrogen trapping and diffusion is well known for special laboratory cast alloys, but unknown for realistic steel compositions. For this reason, a series of S690Q-based alloys were synthesized, close to a real steel composition, but with well controlled Ti or Nb additions in different amounts. Specimens were obtained from these alloys by electrochemical discharge machining (EDM). The specimens were tested using the well-established electrochemical permeation technique. From the experimental results, the hydrogen diffusion coefficients and the analytical subsurface hydrogen concentration were calculated. In addition, the hydrogen trapping behavior at elevated temperatures was interpreted by thermal desorption analysis (TDA) using different heating rates of hydrogen charged samples. The results showed that in contrast to metallurgically "pure" laboratory cast alloys, realistic chemical compositions were similar in their hydrogen trapping behavior, despite some small differences. All investigated steel grades exhibited shallow and reversible hydrogen trapping, regardless of their chemical composition. Of course, the experiments only allowed the calculation of effective diffusion coefficients and trapping energies, which represent an average of the entire microstructure. Nevertheless, HSLA steels are typically joined by arc welding, which includes the risk of delayed hydrogen assisted cracking. From the point of view of welding practice, however, a more or less identical hydrogen diffusion behavior means that no special "metallurgically specific", justifiable measures need to be considered, despite the well-established processes such as "soaking" or dehydrogenation heat treatment. T2 - MPAC 2025 CY - Stuttgart, Germany DA - 06.10.2025 KW - HACC KW - Hydrogen KW - HSLA PY - 2025 AN - OPUS4-64337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichel, Levin A1 - Schroepfer, Dirk A1 - Kromm, Arne A1 - Kannengiesser, Thomas T1 - Stress-Optimised Welding Repair for High-Strength Offshore Steel Joints N2 - The successful energy transition in Germany will require offshore wind turbines with outputs >10 MW in the future. To achieve these high outputs, turbines far from the coast are required, featuring large subsea jacket structures (30 m up to 50 m) and tall towers (up to 200 m). High-strength steels with a yield strengths up to 500 MPa and wall thicknesses of up to 120 mm are increasingly being used for these structures. During manufacture, weld defects detected by non-destructive testing (NDT) require localized repair (gouging and rewelding). To date, there is a lack of repair concepts and information in standards and guidelines. Therefore, BAM initiated the FOSTA project P1629 (IGF 01IF22746N) to investigate the stress-optimized repair (local gouging and welding) of high-strength thick plate joints made of offshore grades in the yield strength range off 355 to 460 MPa and similar weld metal. This research aims to develop a stress-optimized repair concept for thick plate joints, using controlled high-performance GMAW processes and optimized, narrow gouging grooves. Thermal and mechanical gouging are performed, allowing the groove configuration to be modified. Modern welding processes provide deep root penetration and focused energy input capable of welding narrow seams. The aimed residual stress reduction can be attributed to the lower input of weld metal due to the changes in groove configuration and to the reduction in heat input per layer due to the controlled arc process. The experimental analyses take into account the interaction of process, material, and design-related influences on the formation of weld induced stresses. Concluding with recommendations for guidelines elaborated for steel-processing SMEs. T2 - MPA Stuttgart 2025 CY - Stuttgart, Germany DA - 06.10.2025 KW - Repair welding KW - Residual stress KW - High-strength steels KW - Gouging KW - Modern welding processes PY - 2025 AN - OPUS4-64347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, Nina A1 - Rhode, Michael A1 - Kannengießer, Thomas A1 - Kromm, Arne A1 - Kadoke, Daniel A1 - Kruse, Julius T1 - Effect of Ti microalloying on the local strain behavior of cross-weld tensile samples determined by digital image correlation N2 - High-strength low-alloyed (HSLA) steels with yield strength / proof stress ≥ 600 MPa are the basis of modern light-weight steel constructions. Indeed, the economic and ecological benefits strongly depend on their processability in terms of welding. In this context, the use of highly productive welding processes and suitable welding consumables is of vital interest and requires a fundamental understanding of the microstructural changes in the HSLA steel and especially the heat-affected zone (HAZ) of the welded joint. Microalloying elements, such as Ti or Nb, are essential to achieve the desired mechanical properties. To analyse the weldability, three-layer welds were performed using gas metal arc welding (GMAW) and critical microstructures, such as areas of the HAZ that exhibit significant softening or hardening, were identified. The effect of the softened HAZ region on failure was evaluated using cross-weld tensile specimens. Digital image correlation (DIC) was used for in-situ monitoring of the development and accumulation of the local strains in different HAZ regions during tensile testing. Using a specially designed mirror system, the local strains of the microstructure zones on the top and bottom of the weld were recorded simultaneously. In addition, the analysis of the local deformation helps to understand the effects of the softened HAZ on the global strain, the reduction in area, the fracture position, and the overall fracture behavior. KW - High-strength structural steel KW - Microalloying influences KW - HAZ-softening KW - Digital Image Correlation KW - Constraint effect KW - Thermodynamic simulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-643558 DO - https://doi.org/10.1007/s40194-025-02185-1 SP - 1 EP - 17 PB - Springer Nature AN - OPUS4-64355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Uhlig, Marvin A1 - Schröder, Nina A1 - Höfer, Kevin A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Hensel, Jonas T1 - Schweißverfahrensqualifikation an Stumpfnahtverbindungen aus Altstahl- und Feinkornbaustahl N2 - Der Erhalt und die Ertüchtigung bestehender Stahltragwerke gewinnen im Bauwesen zunehmend an Bedeutung. Besonders betroffen sind Konstruktionen aus sogenannten Flussstählen, die im Zeitraum zwischen etwa 1880 und 1940, noch vor Einführung der ersten Stahlnorm DIN 488-1, in großem Umfang im Brücken-, Wasserbau- und Hochspannungsanlagenbau verwendet wurden. Diese Stähle wurden in historischen erstellungsverfahren wie dem Thomas-, Bessemer- oder Siemens-Martin-Verfahren erzeugt und weisen im Vergleich zu heutigen Baustählen eine deutlich größere Streuung in ihren chemischen und mechanischen Eigenschaften auf. Trotz ihres hohen Alters sind viele dieser Tragwerke nach wie vor im Betrieb und befinden sich am Rande ihrer statischen und funktionalen Anforderungen. Ihr Rückbau und Ersatz durch Neubauten sind jedoch oftmals mit erheblichem wirtschaftlichem, logistischem und ökologischem Aufwand verbunden. Daher rückt die Instandhaltung und Weiterverwendung solcher Altbauwerke verstärkt in den Fokus von Infrastrukturprogrammen, Sanierungsstrategien und besitzt eine große kulturelle Bedeutung. Im Rahmen der vorliegenden Untersuchung soll das Potenzial des MAG-Schweißens mit G 18 8 Mn Zusatzwerkstoff für Stumpfnahtverbindungen aus Flussstahl und Feinkornbaustahl qualifiziert werden. Ziel ist es, durch experimentelle und werkstofftechnische Analysen weitere Erkenntnisse über die Schweißbarkeit historischer Stähle zu gewinnen, Anwendungsempfehlungen für die Praxis abzuleiten und damit einen Beitrag zur sicheren und wirtschaftlichen Sanierung historischer Infrastrukturbauwerke zu leisten. T2 - DVS Congress 2025 CY - Essen, Germany DA - 16.09.2025 KW - Altstahl KW - MAG-Schweißen KW - Seigerungen KW - Instandsetzung KW - Feinkornbaustahl PY - 2025 SN - 978-3-96144-298-0 VL - 401 SP - 1 EP - 17 AN - OPUS4-64278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichel, Levin A1 - Schroepfer, Dirk A1 - Kromm, Arne A1 - Kannengiesser, Thomas T1 - Reduction of residual stress by narrowing the repair groove: Optimising repair welding with modern welding processes for high strength offshore steels N2 - The ongoing German energy transition will require offshore wind turbines with outputs of >10 MW in the future. Turbines with these high outputs must be located far from the coast, with up to 50 m large subsea jacket structures and tall towers. These structures are increasingly fabricated of high-strength steels with a yield strength up to 500 MPa and wall thicknesses of up to 120 mm. During production, weld defects identified through non-destructive testing (NDT) must be locally repaired by gouging and rewelding. Standards and guidelines lack sufficient concepts and information regarding such repair procedures. To address this gap, BAM launched the FOSTA project P1629 (IGF 01IF22746N) to explore stress-optimised repair concepts, specifically local gouging and welding, for high-strength thick plate joints made from offshore-grade steels with yield strengths between 355 MPa and 460 MPa, including matching weld metals. This research aims to develop a stress-optimised repair concept for thick plate joints, utilising controlled high-performance GMAW techniques and narrow gouging grooves. Both thermal and mechanical gouging methods are applied, enabling adjustments to the groove geometry. Modern welding processes offer deep root penetration and concentrated energy input, making them suitable for narrow seams. The intended reduction in residual stress results from the decreased weld metal volume, due to modified groove shapes and the lower heat input per layer achieved through controlled arc processes. Experimental investigations examine how process parameters, material properties, and design factors interact to influence the development of welding-induced stresses. The project concludes with practical recommendations for guidelines tailored to steel-processing SMEs. T2 - 4th International Conference on Advanced Joining Processes (AJP 2025) CY - Coimbra, Portugal DA - 16.10.2025 KW - Repair welding KW - Residual stress KW - Modern welding processes KW - High-strength offshore steel KW - Narrow groove PY - 2025 AN - OPUS4-64887 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas T1 - Wasserstoffanalytik und Wasserstoffdegradation von metallischen Werkstoffen T2 - Werkstofftechnisches Kolloquium (öffentlich), Zentrum für Konstruktionswerkstoffe, Institut für Werkstoffkunde Prof. Berger CY - Darmstadt, Germany DA - 2010-04-22 PY - 2010 AN - OPUS4-21287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. A1 - Schillinger, B. T1 - Measuring hydrogen distributions in iron and steel using neutrons N2 - Neutron tomography has been applied to investigate the mechanism of hydrogen assisted cracking in technical iron and supermartensitic steel. Rectangular technical iron block samples showed blistering due to intense hydrogen charging and the tomographic method revealed in situ the spatial distribution of hydrogen and cracks. Hydrogen accumulated in a small region around cracks and the cracks are filled with hydrogen gas. Cracks close to the surface contained no hydrogen. Hydrogenous tensile test samples of supermartensitic steel were pulled until rupture and showed hydrogen accumulations at the notch base and in the plastically deformed region around the fracture surface. T2 - 10th World Conference on Neutron Radiography (WCNR) CY - Grindelwald, Switzerland DA - 05.10.2014 PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-348022 DO - https://doi.org/10.1016/j.phpro.2015.07.062 SN - 1875-3892 VL - 69 SP - 445 EP - 450 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-34802 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - In-situ-phase analysis using synchrotron radiation of low transformation temperature (LTT) welding material N2 - Cold cracking resistance is a relevant evaluation criterion for welded joints and affected by residual stresses which result from the welding procedure. Compressive residual stresses can thereby have a positive influence on preventing cracking. A unique possibility of generating compressive residual stresses already during the welding procedure is offered by the so-called Low Transformation Temperature (LTT) filler wires. Compared to conventional wires, these materials show decreased phase transformation temperatures which can work against the cooling-specific contraction. In consequence, distinct compressive residual stresses can be observed within the weld and adjacent areas. The strength of these fillers makes them potentially applicable to high-strength steel welding. Investigations were carried out to determine the phase transformation behaviour of different LTT-filler materials. Transformation temperatures were identified using Single Sensor Differential Thermal Analysis (SS-DTA). Additionally Synchrotron radiation was used to measure the transformation kinetics of all involved crystalline phases during heating and cooling of a simulated weld thermal cycle. KW - In-situ phase analysis KW - Energy dispersive diffraction KW - Phase transformation KW - Low Transformation Temperature filler wire PY - 2009 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-205922 DO - https://doi.org/10.1590/S0104-92242009000100010 SN - 0104-9224 SN - 1980-6973 VL - 14 IS - 1 SP - 82 EP - 88 PB - Associação Brasileira de Soldagem, ABS CY - Rio de Janeiro AN - OPUS4-20592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Kromm, Arne T1 - Formation of welding residual stresses in low transformation temperature (LTT) materials N2 - For the safety and cost efficiency of welded high-strength steel structures, precise knowledge of the level and distribution of welding- and cooling-specific stresses and residual stresses is essential, since they exert a decisive influence on strength, crack resistance, and finally on the bearable service load. This paper presents innovative filler materials, of which the phase transformation temperature was deliberately adjusted via the chemical composition. The transformation behaviour of these martensitic Low Transformation Temperature (LTT-) filler materials shows direct effects on the local residual stresses in the weld and the HAZ. These effects can purposefully be exploited to counteract the thermally induced shrinkage of the material and to produce significant compressive residual stresses in the weld. Comparative welding experiments were carried out on 690 MPa high-strength base materials using various LTT-filler materials. High energy synchrotron radiation was used for residual stress measurement. Particularly the use of high energy synchrotron radiation makes it possible to detect the residual stress condition fast without destruction of material. Thereby, residual stress depth gradients can be determined simultaneously without removing material. In steel, gradients of up to 150 µm can be resolved in such a way. Furthermore, the application of high energy radiation permits determination of residual stresses of any available residual austenite contents. Results show significant dependence of transformation temperatures on the resulting residual stress level and distribution. KW - Phase specific residual stresses KW - Phase transformation KW - Low transformation temperature filler wire KW - Energy dispersive diffraction KW - High strength steel PY - 2009 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-205909 DO - https://doi.org/10.1590/S0104-92242009000100009 SN - 0104-9224 SN - 1980-6973 VL - 14 IS - 1 SP - 74 EP - 81 PB - Associação Brasileira de Soldagem, ABS CY - Rio de Janeiro AN - OPUS4-20590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Dittmann, Florian A1 - Kromm, Arne A1 - Varfolomeev, Igor A1 - Kannengiesser, Thomas T1 - Improvement of Fatigue Resistance through the Application of a Low-Transformation-Temperature Welding Consumable N2 - Low transformation temperature (LTT) welding consumables are an innovative approach to reduce tensile residual stress in weld seams and the surrounding heat affected zone (HAZ). The reduced tensile stress can lead to an improvement in fatigue strength of welded components. LTT alloys are characterized by a chemical composition which reduce the martensite start temperature (Ms) close to room temperature. This article focuses on a hybrid use of LTT filler metals, where the LTT filler is applied as an additional layer to conventional welds on fatigue-critical spots. Conventional gas metal arc welded longitudinal stiffeners are used as specimens. At the face ends of the stiffeners, a second LTT layer was added with various modifications in weld shapes. These different shapes were achieved by changing the welding parameters such as welding speed and offset to the first layer. These samples were used to analyze shape, dilution, resulting Ms, residual stress and fatigue strength. The dilatometer verified Ms and dilution did not change significant, although the area of the 2nd LTT weld seam was varying clear with each modification. However, the weld modification had a significant effect on the residual stress state and the fatigue strength. The X-ray determined residual stress in the HAZ became lower when the weld toe of the LTT layer was further away from the stiffener. All samples with LTT weld exhibit significantly higher fatigue strength values than conventionally single and double-layer welded samples. The lower the residual stress at weld toe, the higher the fatigue strength. The results show that on the one hand LTT filler metals increase the fatigue strength, and on the other hand the impact of LTT fillers materials is not restricted to the dilution and Ms, the shape of the weld seam must also be considered. T2 - 4th international Conference on Advanced Joining Processes AJP CY - Combria, Portugal DA - 16.10.2025 KW - Low transformation temperature (LTT) KW - Residual stress reduction KW - Fatigue strength KW - Longitudenal stiffener PY - 2025 AN - OPUS4-65090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Engelking, Loenz A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas A1 - Eissel, Antonia A1 - Treutler, Kai A1 - Wesling, Volker T1 - Herstellung beanspruchungsgerechter Oberflächen durch Kombination innovativer additiver und abtragender Fertigungsschritte an hochbelasteten Komponenten N2 - Die additive Fertigung mittels Schweißverfahren bietet große ökonomische Vorteile für eine ressourceneffiziente Bauteilherstellung. Offene Fragen bezüglich Homogenität, Anisotropie der Schweißgefüge und den damit verbundenen Bauteileigenschaften stehen einer wirtschaftlichen Verarbeitung oftmals im Wege. Finale Bauteilgeometrie und Oberflächengüte erfordern meist komplementäre subtraktive Fertigungsschritte. Werkstoffe für hochbelastbare Komponenten sind oftmals schwer span bar. In einem Vorhaben der BAM und des ISAF wurde untersucht, wie die Modifikation der AM-Schweißzusätze und das ultraschallunterstützte Fräsen (US) die Zerspanungssituation verbessern. Der vorliegende Artikel stellt wesentliche Zusammenhänge zwischen Legierung, Gefüge und Zerspanung zweier schwer spanbarer Hochleistungslegierungen (FeNi und CoCr) dar. Großes Potenzial zeigte neben dem US die Modifikation mit Zr und Hf bei Zulegierung in das Schweißgut mittels Beschichtung von Massivdrähten bzw. Herstellung von Fülldrähten. KW - Additive Fertigung (AM) KW - Ultraschallunterstütztes Fräsen (US) KW - Werkstoffmodifikation KW - Oberflächenintegrität KW - Zerspanbarkeit schwer spanbarer Legierungen KW - Ressourceneffizienz in Prozessketten KW - Hochleistungslegierungen KW - Technologietransfer für KMU PY - 2025 SN - 978-3-96144-304-8 VL - 2026 SP - 290 EP - 298 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-65246 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas T1 - Cold Cracking Tests - An Overview of Present Technologies and Applications T2 - IIW Annual Assembly CY - Denver, CO, USA DA - 2012-07-09 PY - 2012 AN - OPUS4-26162 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -