TY - JOUR A1 - Rhode, Michael A1 - Schaupp, Thomas A1 - Münster, C. A1 - Mente, Tobias A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas T1 - Hydrogen determination in welded specimens by carrier gas hot extraction - a review on the main parameters and their effects on hydrogen measurement N2 - Carrier gas hot extraction (CGHE) is a commonly applied technique for determination of hydrogen in weld joints using a thermal conductivity detector (TCD) for hydrogen measurement. The CGHE is based on the accelerated hydrogen effusion due to thermal activation at elevated temperatures. The ISO 3690 standard suggests different specimen geometries as well as necessary minimum extraction time vs. temperature. They have the biggest influence on precise hydrogen determination. The present study summarizes the results and experience of numerous test runs with different specimen temperatures, geometries (ISO 3690 type B and small cylindrical samples), and factors that additionally influence hydrogen determination. They are namely specimen surface (polished/as-welded), limited TCD sensitivity vs. specimen volume, temperature measurement vs. effects of PI-furnace controller, as well as errors due to insufficient data assessment. Summarized, the temperature is the driving force of the CGHE. Two different methods are suggested to increase the heating rate up to the desired extraction temperature without changing the experimental equipment. Suggestions are made to improve the reliability of hydrogen determination depended on the hydrogen signal stability during extraction accompanied by Evaluation of the recorded data. Generally, independent temperature measurement with dummy specimens is useful for further data analysis, especially if this data is used for calculation of trapping kinetics by thermal desorption analysis (TDA). KW - Hydrogen KW - Carrier gas hot extraction KW - Experimental design KW - Thermal conductivity device PY - 2019 DO - https://doi.org/10.1007/s40194-018-0664-9 SN - 0043-2288 VL - 63 IS - 2 SP - 511 EP - 526 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-47603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas A1 - Florian, Wolfgang A1 - Böllinghaus, Thomas T1 - Einfluss des Einspanngrades auf die Beanspruchung beim Schweißen eingespannter Bauteile T2 - 18. Tagung Werkstoffprüfung 2000 ; 18. Vortrags- und Diskussionstagung Werkstoffprüfung 2000 CY - Bad Nauheim, Deutschland DA - 2000-12-07 PY - 2000 SP - 95 EP - 102 PB - Dt. Verband für Materialforschung CY - Berlin AN - OPUS4-980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kannengießer, Thomas A1 - Mc Inerney, T. A1 - Florian, Wolfgang A1 - Böllinghaus, Thomas A1 - Cross, C.E. ED - Cerjak, H. T1 - The influence of local weld deformation on hot cracking susceptibility T2 - 6th International Seminar on the Numerical Analysis of Weldability CY - Seggauberg, Austria DA - 2001-10-01 PY - 2002 SN - 1-902653-56-4 N1 - Serientitel: Books of IOM3 – Series title: Books of IOM3 IS - 784 SP - 803 EP - 818 PB - Maney CY - London AN - OPUS4-1793 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Kannengießer, Thomas A1 - Jochum, C. A1 - Stiebe-Springer, I. T1 - Effect of filler material selection on stress strain build up and stress corrosion cracking resistance of welded supermartensitic stainless steel pipes T2 - Corrosion 2002 CY - Denver, CO, USA DA - 2002-04-07 KW - Supermartensitic stainless steel KW - Filler material KW - Orbital TIG welding KW - Duplex stainless steel KW - Hydrogen assisted cracking KW - Stress strain distribution KW - Shrinkage restraint KW - Formation water PY - 2002 SP - Paper 02061, 1 EP - 20 PB - NACE International CY - Houston, Tex. AN - OPUS4-1794 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Kannengießer, Thomas T1 - Steps to more conclusive testing of welded supermartensitic stainless steel pipes T2 - 2nd International Conference Supermartensitic Stainless Steels 2002 CY - Brussels, Belgium DA - 2002-10-03 KW - Component testing KW - Conclusive test sequences KW - Hydrogen assisted cracking KW - Supermartensitic stainless steels KW - Martensite transformation KW - Welded pipelines PY - 2002 SP - 71 EP - 76 PB - KCI Publ. CY - Zutphen AN - OPUS4-2301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas A1 - Zimmer, Peter T1 - Investigations of Cold Cracking by the CTS-Test at Various Cooling Conditions T2 - 56th IIW International Conference Welded Construction for Urban Infrastructure CY - Bucharest, Romania DA - 2003-07-10 KW - Kaltrisstests KW - Schweißsicherheit PY - 2003 SN - 0043-2288 SN - 1878-6669 VL - 47 SP - 1(?) EP - 12(?) PB - Springer CY - Oxford AN - OPUS4-2630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böllinghaus, Thomas A1 - Kannengießer, Thomas A1 - Schobbert, Helmut T1 - Neue werkstofftechnische Erkenntnisse und Ergebnisse aus der BAM PY - 2003 SN - 0935-0292 VL - 18.2004 SP - 80 EP - 90 PB - Verl. für Schweißen u. Verwandte Verfahren DVS-Verl. CY - Düsseldorf AN - OPUS4-2656 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Seeger, D.M. A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas T1 - Risssicherheit von Schweißnähten an Pipelines der Offshore-Industrie aus supermartensitischem Stahl T2 - Schweißen und Schneiden 2005 CY - Essen, Deutschland DA - 2005-09-12 KW - Supermartensit KW - Risssicherheit KW - Geschlossene Prüfkette PY - 2005 SN - 3-87155-695-5 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 237 SP - 85 EP - 91 PB - DVS-Verl. CY - Düsseldorf AN - OPUS4-11083 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Zimmer, Peter A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas T1 - Kaltrissprüfverfahren nach der DVS Richtlinie 1006 T2 - Schweißen und Schneiden 2005 CY - Essen, Deutschland DA - 2005-09-12 KW - Kaltriss KW - Kaltrissprüfung KW - DVS-Richtlinie 1006 PY - 2005 SN - 3-87155-695-5 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 237 SP - 275 EP - 280 PB - DVS-Verl. CY - Düsseldorf AN - OPUS4-11084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stelling, Karen A1 - Schobbert, Helmut A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas T1 - Vertical-up and -down laser plasma powder hybrid welding of a high nitrogen austenitic stainless steel KW - Laser welding KW - Photon beam welding KW - Radiation welding KW - Plasma welding KW - Arc Welding KW - Gas shielded arc welding KW - Vertical down KW - Vertical position KW - Welding position KW - Vertical up KW - Process parameters KW - Process conditions KW - Speed KW - Austenitic stainless steels KW - Stainless steels KW - Steels PY - 2005 SN - 0043-2288 SN - 1878-6669 VL - 49 IS - 5/6 SP - 45 EP - 49 PB - Springer CY - Oxford AN - OPUS4-11885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Zimmer, Peter A1 - Kannengießer, Thomas A1 - Florian, Wolfgang A1 - Böllinghaus, Thomas T1 - Kaltrissprüfungen für hochfeste Feinkornbaustähle T2 - Große Schweißtechnische Tagung "Schweißen und Schneiden" 2004 CY - Magdeburg, Deutschland DA - 2004-09-22 PY - 2004 SN - 3-87155-689-0 SN - 0418-9639 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 232 SP - 207 EP - 214 PB - DVS-Verl. CY - Düsseldorf AN - OPUS4-4634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Neuhaus, Mathias A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas A1 - Herold, H. A1 - Hoffmeister, H. T1 - Beurteilung der Kaltrisssicherheit von Schweißverbindungen in realen Konstruktionen mit der Finite-Elemente-Methode T2 - Große Schweißtechnische Tagung "Schweißen und Schneiden" 2004 CY - Magdeburg, Deutschland DA - 2004-09-22 PY - 2004 SN - 3-87155-689-0 SN - 0418-9639 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 232 SP - 195 EP - 200 PB - DVS-Verl. CY - Düsseldorf AN - OPUS4-4635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas A1 - Neuhaus, M. T1 - Effects of the load history on the residual stress distribution in welded components KW - Loading KW - Residual stresses KW - Stress distribution KW - Influencing factors KW - Practical investigations KW - Measurement KW - Cooling KW - Hardness KW - Mechanical properties KW - Temperature distribution KW - Heat affected zone KW - Weld zone KW - Yield strength KW - Strength KW - Parent material KW - Restraint PY - 2006 SN - 0043-2288 SN - 1878-6669 VL - 50 IS - 7/8 SP - 11 EP - 17 PB - Springer CY - Oxford AN - OPUS4-12516 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kannengießer, Thomas A1 - Florian, Wolfgang A1 - Böllinghaus, Thomas A1 - Herold, H. ED - Miannay, D. P. T1 - Analysis of welding reaction stresses and welding reaction moments in component tests - Stress characteristics dependent on the intensity of restraint N2 - Up to the present, the thermomechanical loads during welding and subsequent cooling under design-specific shrinkage restraint resulting from the interaction between the materials and the structure have often not been taken into consideration approperiately for weldability assessment of components. As compared to previous investigations using small specimens this report presents component weld tests under varying intensities of restraint. Online records of the reaction forces and moments demonstrate in which way the intensity of restraint affects the reaction stresses and moments and their meaning for the evaluation of the load level in welded components. T2 - EUROMAT Topical 2000 CY - Tours, France DA - 07.11.2000 PY - 2000 SN - 0-08-042815-0 VL - 1 SP - 145 EP - 150 PB - Elsevier CY - Amsterdam AN - OPUS4-11847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böllinghaus, Thomas A1 - Kannengießer, Thomas A1 - Neuhaus, Mathias ED - Cerjak, H. ED - Bhadeshia, H. K. D. H. T1 - Effects of the structural restraint intensity on the stress strain build up in butt joints T2 - 7th International Seminar on Numerical Analysis of Weldability CY - Graz, Austria DA - 2003-09-29 PY - 2005 SN - 3-901351-99-X SP - 651 EP - 669 PB - Techn. Univ., TUG CY - Graz AN - OPUS4-11850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Zimmer, Peter A1 - Böllinghaus, Thomas A1 - Kannengießer, Thomas T1 - Effects of hydrogen on weld microstructure mechanical properties of the high strength steels S 690Q and S 1100QL PY - 2004 UR - http://www.china-weldnet.com/English/information/II-1525-04.htm IS - II-1525-04 SP - 1 EP - 16 PB - International Institute of Welding CY - Paris AN - OPUS4-11851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas A1 - Florian, Wolfgang A1 - Herold, H. T1 - Effect of weld metal strength and welding conditions on reaction forces and stress distribution of restrained components N2 - Düring the past decades, weldability studies have predominantly been concentrated on the material and the welding process. In order to achieve a closer insight into the structural effects, component weldability tests have been performed by online monitoring of the reaction forces and moments. As a particular item, the effects of different strengths of the base and filier material on the reaction force and stress build up transverse to the welding direction have been studied at a specific structural restraint. As a most relevant result for practical welding it is demonstrated that the final reaction force and also the reaction stress level in the multilayer butt welds decreases with overmatch of the weld metal. PY - 2000 IS - IX-1971-00 SP - 1 EP - 18 PB - International Institute of Welding CY - Paris AN - OPUS4-11842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Eliezer, D. A1 - Böllinghaus, Thomas T1 - In situ synchrotron X-ray radiation analysis of hydrogen behavior in stainless steel subjected to continuous heating N2 - Hydrogen generally causes lattice distortions and phase transformations when introduced into a metallic crystal lattice. For the investigations reported in this contribution, hydrogen thermal desorption analysis has been carried out to observe the influence of hydrogen desorption on the lattice of super martensitic stainless steel during continuous heating. The lattice expansion parameter and the phase transformations have been monitored during the thermal desorption process, and the influence of hydrogen on such characteristics has been evaluated. It was found that hydrogen has a significant influence on both the lattice parameter and on the thermal expansion. However, hydrogen has no influence on phase transformation during thermal desorption. The hydrogen's desorption behavior in this process was also observed and it turned out that hydrogen desorbs in two stages, i.e., firstly diffusible hydrogen and trapped hydrogen afterward. KW - Synchrotron radiation KW - In situ KW - Hydrogen PY - 2012 DO - https://doi.org/10.1007/s10853-012-6489-9 SN - 0022-2461 SN - 1573-4803 VL - 47 IS - 15 SP - 5879 EP - 5885 PB - Springer Science + Business Media B.V. CY - Norwell, Mass. AN - OPUS4-26179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lausch, Thomas A1 - Kannengießer, Thomas A1 - Schmitz-Niederau, M. T1 - Multi-axial load analysis of thick-walled component welds made of 13CrMoV9-10 N2 - A 20 mm thick heat resistant 13CrMoV9-10 steel was welded using a multi-pass submerged arc tandem setup on a 3-D testing facility designed to prevent shrinkage both during the welding and the subsequent cooling to room temperature. The effects of variations in pre-heating and interpass temperatures on the local stresses were monitored by in situ measurement of reaction forces and bending moments during welding and the subsequent dehydrogenation heat treatment. The austenite to bainite transformation and its effects on the overall loads were monitored through the use of a high sampling rate. Increasing the pre-heating and interpass temperatures led to a rise in reaction forces and bending moments. The bending moments originated from the eccentric force transmission over the backing, with a concomitant risk of fracture, especially in the critical root zone. Although the pre-heating and interpass temperatures had a strong effect on the reaction forces, their effect on the bending moments upon cooling to room temperature was negligible. KW - Component welding KW - Clamping KW - Submerged arc welding KW - Heat input KW - Reaction force KW - Reaction moment PY - 2013 DO - https://doi.org/10.1016/j.jmatprotec.2013.01.008 SN - 0924-0136 SN - 1873-4774 VL - 213 IS - 7 SP - 1234 EP - 1240 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-27953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wolf, Martin A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas ED - Carl E. Cross, ED - John C. Lippold, ED - Böllinghaus, T. ED - Herold, H. T1 - Determination of critical strain rate for solidification cracking by numerical simulation PY - 2008 SN - 978-3-540-78627-6 IS - Part I SP - 77 EP - 92 PB - Springer CY - Berlin AN - OPUS4-24488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -