TY - CONF A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas A1 - Lausch, Thomas T1 - Untersuchungen zum Einfluss der Wärmeführung auf die Eigenspannungsausbildung und Gesamtbeanspruchung in Schweißverbindungen aus hochfestem Feinkornbaustahl N2 - In modernen Schweißkonstruktionen des Stahl- und Ingenieurbaus werden zunehmend hochfeste Feinkornbaustähle eingesetzt. Grundsätzlich sind während der schweißtechnischen Verarbeitung hochfester Stahlgüten aufgrund ihres speziellen Gefüges und wegen ihres vergleichweise hohen Streckgrenzenverhältnisses engere Verfahrensgrenzen einzuhalten, als bei Stählen mit niedrigerer Festigkeit. Die Sicherheit von hochfesten Schweißverbindungen erfordert präzise Kenntnisse über die Höhe und Verteilung der schweißbedingten Beanspruchungen, da sie die erreichbare Tragfähigkeit unmittelbar beeinflussen. In den Untersuchungen wurde der Einfluss der Wärmeführung in Form der Zwischenlagentemperatur und Streckenenergie auf die Eigenspannungsausbildung und Gesamtbeanspruchung in hochfesten Schweißverbindungen ermittelt. Zur Berücksichtigung einer äußeren Bauteilsteifigkeit wurden die Proben in Nahtquerrichtung unter einem definierten Einspanngrad in einer speziellen Prüfanlage (CTW-Test) mehrlagig geschweißt. Es zeigte sich beispielsweise, dass insbesondere die Zwischenlagentemperatur einen direkten Einfluss auf die globalen Reaktionsspannungen hat. Ferner bedingt die Erhöhung der Wärmeführung ein deutliches Anheben der Zugeigenspannungen im Bereich des Schweißgutes. T2 - DVS Congress 2013 - Große Schweißtechnische Tagung CY - Essen, Germany DA - 16.09.2013 KW - Eigenspannungen KW - MAG-Schweißen KW - Einspanngrad KW - Hochfeste Feinkornbaustähle KW - Wärmeführung KW - Schweißparameter PY - 2013 SN - 978-3-87155-614-2 VL - 296 SP - 339 EP - 344 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-30687 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhang, Lei A1 - Pittner, Andreas A1 - Michael, Thomas A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Effect of cooling rate on microstructure and properties of microalloyed HSLA steel weld metals N2 - Two high strength Nb/Ti microalloyed S690QL steels were welded with identical filler material, varying welding parameters to obtain three cooling rates: slow, medium and fast cooling. As cooling rate increased, the predominantly acicular ferrite in Nb weld metal (WM) is substituted by bainite, with a consequence of obvious hardness increase, but in Ti WM, no great variation of acicular ferrite at all cooling rates contributed to little increment of hardness. The transition between bainite and acicular ferrite has been analysed from the point view of inclusions characteristics, chemical composition and cooling rate. Excellent Charpy toughness at 233 K was obtained with acicular ferrite as predominantly microstructure. Even with bainite weld of high hardness, the toughness was nearly enough to fulfill the minimal requirements. WM for Ti steel showed to be markedly less sensitive to the variations of cooling rate than that for Nb steel. KW - High strength steel KW - Weld metal KW - Cooling rate KW - Charpy toughness KW - Acicular ferrite PY - 2015 DO - https://doi.org/10.1179/1362171815Y.0000000026 SN - 1362-1718 VL - 20 IS - 5 SP - 371 EP - 377 PB - Taylor and Francis CY - London, UK AN - OPUS4-36518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichel, Levin A1 - Kromm, Arne A1 - Michael, Thomas A1 - Schroepfer, Dirk A1 - Kannengiesser, Thomas T1 - Modern welding processes for optimizing repair welding on high-strength offshore steels N2 - The successful energy transition in Germany will require offshore wind turbines with outputs >10 MW in the future, for which high-strength steels with a yield strength of up to 500 MPa and wall thicknesses up to 150 mm are increasingly being used. The repair of weld seams when detecting defects during NDT requires localized gouging and rewelding. This involves high demands on welding manufacturing, especially for highstrength steels. Due to a lack of investigations, there are no repair concepts and information in standards and guidelines, particularly for high-strength thick plate joints made of high-strength offshore steels. However, these are urgently needed to enable processors, especially SMEs, to carry out safe and economical repairs. Therefore, BAM startedthe FOSTA project P1629 (IGF 01IF22746N) to investigate the stress-optimized repair(local gouging and welding) of high-strength thick plate joints made of offshore grades in the yield strength range off 355 to 460 MPa and similar weld metal with controlled high-performance GMAW processes and optimized narrower gouging grooves. The experimental analyses consider the complex interaction of material, process, and designrelated influences on the formation of weld-related stresses and the special microstructure of high-strength fine-grain structural steels. Welding-related material Degradation and crack-critical residual tensile stresses need to be avoided to ensure high component safety and performance. With component-related welding experiments on special testing equipment, adapted process and heat control concepts along with variable groove configurations will be developed and recommendations for guidelines elaborated. This is the prerequisite for fully utilizing the strength potential of high-strength steels and making a valuable contribution to the energy transition in Germany, especially for steelprocessing SMEs. T2 - 6. Symposium Materialtechnik CY - Clausthal-Zellerfeld, Germany DA - 20.02.2025 KW - Narrow groove KW - Optimized repair welding KW - Modern welding processes KW - High-strength steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636520 DO - https://doi.org/10.21268/20250507-5 SP - 3 EP - 15 AN - OPUS4-63652 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Lorenz, Stephan A1 - Kannengießer, Thomas A1 - Michael, Thomas A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Posch, G. T1 - Laserstrahl-MSG-Hybridschweißen mit hochlegierten Massiv- und Fülldrahtelektroden T2 - Die Verbindungs Spezialisten 2009 - Große Schweißtechnische Tagung CY - Essen, Deutschland DA - 2009-09-14 KW - Laserstrahl-MSG-Hybridschweißen KW - Hochlegiert KW - 1.4306 KW - AISI 304L KW - Positionsschweißen KW - Metastabiler austenitischer Chrom-Nickel-Stahl KW - Metallurgie PY - 2009 SN - 978-3-87155-584-8 VL - 258 SP - 75 EP - 80 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-20107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lausch, Thomas A1 - Steger, Jörg A1 - Kannengießer, Thomas A1 - Schmitz-Niederau, M. T1 - Multiaxiale Belastungsanalyse an dickwandigen Bauteilschweißungen aus 13CrMoV9-10 N2 - Große Materialstärken und komplexe Strukturen bewirken eine erhebliche Schrumpfbehinderung der Schweißnaht. Die aus dem Schweißprozess resultierenden multiaxialen Belastungen tragen maßgeblich zur Gesamteigenbeanspruchung einer Schweißkonstruktion bei und lassen sich nur unter realen Fertigungsbedingungen analysieren. Zur wirklichkeitsnahen Simulation der komplexen Steifigkeitsverhältnisse realer Bauteile wurden hierzu in einer speziellen 3D-Prüfanlage UP-Mehrlagenschweißungen am warmfesten Stahl 13CrMoV9-10 durchgeführt. Während der schweißtechnischen Fertigung sowie der Abkühlung auf Raumtemperatur wurden die Proben an der freien Ausdehnung und Schrumpfung gehindert. Der Einfluss der Wärmeführung, d.h. Streckenenergie (E) und Vorwärm-/Zwischenlagentemperatur (T(Pli>), auf die resultierende Bauteilbeanspruchung wurde durch in-situ Messungen der Reaktionskräfte (Fy) und Biegemomente (Mx) während des Schweißens und der anschließenden Wasserstoffarmglühung untersucht. Sowohl die Reaktionskräfte als auch die Biegemomente steigen mit zunehmender Vorwärmtemperatur an und somit erhöht sich die Beanspruchung des Wurzelbereiches. Während die Vorwärm-/Zwischenlagentemperatur einen signifikanten Einfluss auf die resultierenden Reaktionskräfte hat, ist der Einfluss auf die Biegemomente nach Abkühlung auf Raumtemperatur vernachlässigbar. Eine Erhöhung der Streckenenergie wirkt sich nur geringfügig auf die Höhe der Endreaktionskraft aus, beeinflusst aber signifikant das resultierende Biegemoment nach erfolgter Abkühlung auf Raumtemperatur. T2 - DVS Congress 2014 - Große Schweißtechnische Tagung CY - Berlin, Germany DA - 15.09.2014 KW - Schrumpfbehinderung KW - 13CrMoV9-10 KW - Reaktionskräfte KW - Biegemoment KW - Wärmeführung PY - 2014 SN - 978-3-945023-03-7 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte VL - 306 SP - 42 EP - 48 AN - OPUS4-31523 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schaupp, Thomas A1 - Schröder, Nina A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas T1 - Hydrogen-Assisted Cracking in GMA Welding of High-Strength Structural Steel—A New Look into This Issue at Narrow Groove N2 - Modern arc processes, such as the modified spray arc (Mod. SA), have been developed for gas metal arc welding of high-strength structural steels with which even narrow weld seams can be welded. High-strength joints are subjected to increasingly stringent requirements in terms of welding processing and the resulting component performance. In the present work, this challenge is to be met by clarifying the influences on hydrogen-assisted cracking (HAC) in a high-strength structural steel S960QL. Adapted samples analogous to the self-restraint TEKKEN test are used and analyzed with respect to crack formation, microstructure, diffusible hydrogen concentration and residual stresses. The variation of the seam opening angle of the test seams is between 30° and 60°. To prevent HAC, the effectiveness of a dehydrogenation heat treatment (DHT) from the welding heat is investigated. As a result, the weld metals produced at reduced weld opening angle show slightly higher hydrogen concentrations on average. In addition, increased micro- as well as macro-crack formation can be observed on these weld metal samples. On all samples without DHT, cracks in the root notch occur due to HAC, which can be prevented by DHT immediately after welding. KW - High-strength structural steel KW - Gas metal arc welding KW - Diffusible hydrogen KW - Hydrogen-assisted cracking KW - TEKKEN KW - Residual stresses KW - Weld metal cracking PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527260 DO - https://doi.org/10.3390/met11060904 VL - 11 IS - 6 SP - 904 PB - MDPI CY - Basel AN - OPUS4-52726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröpfer, Dirk A1 - Kromm, Arne A1 - Lausch, Thomas A1 - Rhode, Michael A1 - Wimpory, R. C. A1 - Kannengießer, Thomas T1 - Influence of welding stresses on relief cracking during heat treatment of a creep-resistant 13CrMoV steel: Part III - Assessment of residual stresses from small-scale to real component welds N2 - For higher operational temperatures and pressures required in petrochemical plants, the modified 13CrMoV9-10 steel was developed providing high resistance against creep and compressed hydrogen. Extreme care during the welding procedure is necessary for this steel, attributed to low toughness, high strength in as-welded state, and increased susceptibility to stress relief cracking (SRC) during post-weld heat treatment (PWHT). Previous research of SRC in creep-resistant steels discussed mainly thermal and metallurgical factors. Few previous findings addressed the influences of welding procedure on crack formation during PWHT considering real-life manufacturing conditions. These investigations focus on effects of welding heat control on stresses during welding and subsequent PWHT operations close to realistic restraint and heat dissipation conditions using a special 3D testing facility, which was presented in parts I and II of this contribution. Part III addresses investigations on residual stress evolution affecting crack formation and discusses the transferability of results from large-scale testing to laboratory-scale. Experiments with test set-ups at different scales under diverse rigidity conditions and an assessment of the residual stresses of the weld-specimens using X-ray (surface near) and neutron diffraction analysis (bulk) were performed. This study aims to provide a way of investigating the SRC behaviour considering component-specific residual stresses via small-scale testing concepts instead of expensive weld mock-ups. KW - Welding KW - Creep-resistant steel KW - Residual stresses KW - Post-weld heat treatment KW - Stress relief cracking PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-524403 DO - https://doi.org/10.1007/s40194-021-01101-7 SN - 1878-6669 VL - 65 SP - 1671 EP - 1685 PB - Springer CY - Berlin AN - OPUS4-52440 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Thomas, Maximilian A1 - Kannengießer, Thomas A1 - Gibmeier, J. A1 - Vollert, F. T1 - Assessment of the Solidification Cracking Susceptibility of Welding Consumables in the Varestraint Test by Means of an Extended Evaluation Methodology N2 - Various test methods are available for assessing the susceptibility of materials to solidification cracking during welding. In the widely used Varestraint test, the crack length is selected as a criterion as a function of the applied bending strain. Unfortunately, the crack length does not characterize the material behavior alone but depends to varying degrees on the individual test parameters used, which makes the interpretation of the results difficult. In addition, the crack length is not comparable under different test conditions. To overcome these disadvantages, we have developed a novel evaluation methodology that decouples the machine influence from the material behavior. The measured crack length is related to the maximum possible value specified by welding speed and deformation time. This relative crack length is calculated numerically, considering the orientation of the cracks. Experiments on two high-alloy martensitic welding consumables show that, in contrast to the conventional evaluation, a comparison of different welding parameters becomes possible. Furthermore, the strain rate proved to be a suitable crack criterion in agreement with Prokhorov's hot cracking model. KW - Welding KW - Solidification cracking KW - Varestraint test PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545780 DO - https://doi.org/10.1002/adem.202101650 SN - 1438-1656 SP - 2101650 PB - Wiley online library AN - OPUS4-54578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lausch, Thomas A1 - Kannengießer, Thomas A1 - Bohse, Jürgen A1 - Schmitz-Niederau, M. T1 - Schallemissionsmessung an Bauteilschweißungen aus 13CrMoV9-10 zum Nachweis von Spannungsrelaxationsrissen N2 - In einer speziellen 3D-Prüfanlage zur wirklichkeitsnahen Simulation von komplexen Verhältnissen an Großproben wurden UP-Mehrlagenschweißungen am warmfesten Stahl 13CrMoV9-10 durchgeführt. Während der schweißtechnischen Fertigung und der Abkühlung auf Raumtemperatur wurden die Proben an der freien Ausdehnung und Schrumpfung gehindert. Die daraus resultierenden Reaktionsspannungen führten während der Wärmenachbehandlung zu Relaxationsrissen in der Wärmeeinflusszone. Das Spannungsarmglühen wurde bei einer Temperatur von 705°C und einer Haltezeit von 8 h durchgeführt. Während der Aufheiz- und Abkühlphasen wurde die thermische Ausdehnung der Probe über die 3D-Prüfanlage kompensiert und damit das Spannungsniveau bis zum Erreichen der maximalen Glühtemperatur aufrechterhalten. Nach Erreichen der Glühtemperatur konnte die Probe relaxieren. Der Einsatz der Schallemissionsmessung ermöglichte es die Entstehung von Spannungsrelaxationsrisse, erstmalig online, nachzuweisen. Durch Synchronisierung der Schallemissionsereignisse mit den Messdaten der 3D – Prüfanlage wurde der kritische Temperaturbereich für das Auftreten von Spannungsrelaxationsrissen bestimmt. Die Rissinitiierung findet im Temperaturbereich zwischen 350°C - 500°C statt. Aussagen über das Risswachstum können auf Grund der ungünstigen Versuchsbedingungen, mit Emission von Störgeräuchen, nicht getroffen werden. T2 - 19. Kolloquium Schallemission - Statusberichte zur Entwicklung und Anwendung der Schallemissionsanalyse CY - Augsburg, Germany DA - 12.09.2013 KW - Spannungsrelaxationsrisse KW - SRC KW - Schallemission KW - 13CrMoV9-10 KW - Schrumpfbehinderung PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-291616 SN - 978-3-940283-51-1 N1 - Serientitel: DGZfP-Berichtsband – Series title: DGZfP-Berichtsband IS - 142 SP - 1 EP - 19 (Beitrag 14) PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung CY - Berlin AN - OPUS4-29161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schaupp, Thomas A1 - Ernst, W. A1 - Spindler, H. A1 - Kannengießer, Thomas T1 - Hydrogen-assisted cracking of GMA welded 960 MPa grade high-strength steels N2 - High-strength steels with yield strength of 960 MPa are susceptible to hydrogen-assisted cracking (HAC) during welding processing. In the present paper, the implant test is used to study HAC in a quenched and tempered steel S960QL and a high-strength steel produced by thermo-mechanical controlled process S960MC. Welding is performed using the gas metal arc welding process. Furthermore, diffusible hydrogen concentration (HD) in arc weld metal is determined. Based on the implant test results, lower critical stress (LCS) for complete fracture, critical implant stress for crack initiation, and embrittlement index (EI) are determined. At HD of 1.66 ml/100 g, LCS is 605 MPa and 817 MPa for S960QL and S960MC, respectively. EI is 0.30 and 0.46 for S960QL and S960MC, respectively. Fracture surfaces of S960QL show higher degradation with reduced deformation. Both, higher EI of S960MC and fractography show better resistance to HAC in the HAZ of S960MC compared to S960QL. KW - High-strength steel KW - Welding KW - Diffusible hydrogen KW - Hydrogen-assisted cracking KW - Heat-affected zone KW - Implant test PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-510307 DO - https://doi.org/10.1016/j.ijhydene.2020.05.077 SN - 0360-3199 VL - 45 IS - 38 SP - 20080 EP - 20093 PB - Elsevier Ltd CY - Amsterdam, NL AN - OPUS4-51030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -