TY - JOUR A1 - Droste, Bernhard A1 - Komann, Steffen A1 - Wille, Frank A1 - Rolle, Annette A1 - Probst, Ulrich A1 - Schubert, Sven T1 - Consideration of aging mechanism influence on transport safety of dual purpose casks for spent nuclear fuel of HLW N2 - When storage of spent nuclear fuel or high level waste is carried out in dual purpose casks (DPC), the effects of aging on safety relevant DPC functions and properties have to be managed in a way that a safe transport after the storage period of several decades is capable and can be justified and certified permanently throughout that period. The effects of aging mechanisms (e.g. radiation, different corrosion mechanisms, stress relaxation, creep, structural changes and degradation) on the transport package design safety assessment features have to be evaluated. Consideration of these issues in the DPC transport safety case will be addressed. Special attention is given to all cask components that cannot be directly inspected or changed without opening the cask cavity, like the inner parts of the closure system and the cask internals, like baskets or spent fuel assemblies. The design criteria of that transport safety case have to consider the operational impacts during storage. Aging is not the subject of technical aspects only but also of ‘intellectual’ aspects, like changing standards, scientific/technical knowledge development and personal as well as institutional alterations. Those aspects are to be considered in the management system of license holders and in appropriate design approval update processes. The paper addresses issues that are subject of an actual International Atomic Energy Agency TECDOC draft 'Preparation of a safety case for a dual purpose cask containing spent nuclear fuel'. KW - Transport KW - Storage KW - Spent fuel KW - High-level waste KW - Aging KW - Metal seals KW - Transport and storage casks KW - Spent nuclear fuel KW - Aging mechanisms KW - Corrosion KW - Safety assessment PY - 2014 U6 - https://doi.org/10.1179/1746510914Y.0000000070 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 25 IS - 3-4 SP - 105 EP - 112 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-33428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Wille, Frank T1 - Transport of large nuclear power plant components: experiences in mechanical design assessment N2 - In the course of decommissioning of power plants in Germany large nuclear components (steam generator, reactor pressure vessel) must be transported over public traffic routes to interim storage facilities, where they are dismantled or stored temporarily. Since it concerns surface contaminated objects or low specific activity materials, a safety evaluation considering the IAEA transport regulations mainly for industrial packages (type IP-2) is necessary. For these types of industrial packages the requirements from normal transport conditions are to be covered for the mechanical proof. For example, a free drop of the package from a defined height, in dependence of its mass, onto an unyielding target, and a stacking test are required. Since physical drop tests are impossible generally due to the singularity of such 'packages', a calculation has to be performed, preferably by a complex numerical analysis. The assessment of the loads takes place on the basis of local stress distributions, also with consideration of radiation induced brittleness of the material and with consideration of recent scientific investigation results. Large nuclear components have typically been transported in an unpackaged manner, so that the external shell of the component provides the packaging wall. The investigation must consider the entire component including all penetration areas such as manholes or nozzles. According to the present IAEA regulations the drop position is to be examined, which causes the maximum damage to the package. In the case of a transport under special arrangement a drop only in an attitude representing the usual handling position (administratively controlled) is necessary. If dose rate values of the package are higher than maximum allowable values for a public transport, then it is necessary that additional shielding construction units are attached to the large component. KW - Radioactive material KW - Large components KW - Decommissioning KW - Nuclear power plant KW - Mechanical assessment KW - Numerical analysis PY - 2009 U6 - https://doi.org/10.1179/174650909X12543085665266 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 20 IS - 4 SP - 149 EP - 153 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-20820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Wille, Frank T1 - Dicht und sicher abgeschirmt N2 - BAM-GGR Transportverpackungen für radioaktive Stoffe müssen den BAM-Gefahrgutregeln entsprechen. Ein kurzer Einblick in die Richtlinien. PY - 2014 SN - 0944-6117 VL - 3 SP - 18 EP - 20 PB - Vogel CY - München AN - OPUS4-30487 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Neumann, Martin A1 - Ballheimer, Viktor A1 - Wille, Frank A1 - Weber, Mike A1 - Qiao, Linan A1 - Droste, Bernhard T1 - Mechanical assessment within type B packages approval: application of static and dynamic calculation approaches N2 - This paper demonstrates exemplarily how numerical and experimental approaches can be combined reasonably in mechanical assessment of package integrity according to the IAEA regulations. The paper also concentrates on the question about how static mechanical approaches can be applied, and what their problems are in relation to dynamic calculation approaches. Under defined impact tests, which represent accident transport conditions, the package has to withstand impact loading, e.g. resulting from a 9 m free drop onto an unyielding target in sequence with a 1 m puncture drop test. Owing to the local character of the interaction between the puncture bar and the cask body, it is possible to develop a dynamic numerical model for the 1 m puncture drop which allows an appropriate simulation of the interaction area. Results from existing experimental drop tests with prototype or small scale cask models can be used for verification and validation of applied analysis codes and models. The link between analysis and experimental drop testing is described exemplarily by considering a regulatory 1 m puncture bar drop test onto the cask body of a recently approved German high level waste transport package. For the 9 m drop test of the package, it is difficult to develop a dynamic numerical model of the package due to the complexity of the interaction between cask body, impact limiters and unyielding target. Dynamic calculations require an extensive verification with experimental results. The simulation of a 9 m drop of a package with impact limiters is thereby often more complex than the simulation of a 1 m puncture drop onto the cask body. A different approximation method can be applied for the consideration of dynamic effects on the impact loading of the package. In a first step, maximum impact force and rigid body deceleration of the cask body during the impact process can be calculated with simplified numerical tools. This rigid body deceleration can subsequently be applied on a verified static numerical model. Dynamic effects, which cannot be covered by the static numerical analysis, have therefore to be considered by using an additional dynamic factor. The paper describes this approach exemplarily for a 9 m horizontal drop of a typical spent fuel cask design. KW - Package assessment KW - Package KW - Packaging KW - Structural analysis PY - 2011 U6 - https://doi.org/10.1179/1746510911Y.0000000012 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 4 SP - 179 EP - 183 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-26448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank T1 - Zur Prüfung verpflichtet - Die BAM-Gefahrgutregel 016 (BAM-GGR 016) N2 - Im Gegensatz zu den zulassungspflichtigen Versandstücken für die gemäß der gefahrgutrechtlichen Regelwerksanforderungen eine behördlich ausgestellte Zulassung erforderlich ist, ist für die prüfpflichtigen Versandstücke lediglich eine behördliche Anerkennung und Überwachung des Managementsystems für die Auslegung, Herstellung, Prüfung, Dokumentation, den Gebrauch, die Wartung und Inspektion erforderlich. In der Bundesrepublik Deutschland ist gemäß den Festlegungen in der Gefahrgutverordnung Straße, Eisenbahn und Binnenschifffahrt die Bundesanstalt für Materialforschung und -prüfung (BAM) zuständig für die Anerkennung und Überwachung von Managementsystemen. KW - Gefahrgut KW - Radioaktive Stoffe KW - Normen KW - Regeln PY - 2018 SN - 0944-6117 VL - 2018 IS - 1-2 SP - 10 EP - 12 PB - Springer Fachmedien München GmbH CY - München AN - OPUS4-44168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank A1 - Droste, Bernhard T1 - Transport von Großkomponenten aus der Stilllegung kerntechnischer Anlagen in Deutschland-Erfahrungen bei der mechanischen Intergritätsbewertung N2 - Im Zuge des Rückbaus kerntechnischer Anlagen in Deutschland müssen u. a. Großkomponenten (Dampferzeuger, Reaktordruckbehälter) über öffentliche Verkehrswege in Zwischenlager transportiert werden, in denen sie zerlegt bzw. zwischengelagert werden. Da es sich hierbei um aktivierte und/oder oberflächenkontaminierte Objekte handelt, ist eine Begutachtung unter Berücksichtigung der Gefahrgutbeförderungsvorschriften notwendig. In den meisten Fällen handelt es sich um oberflächenkontaminierte Gegenstände, welche als Industrieversandstücke des Typs IP-2 zu befördern sind. KW - Zwischenlagerung KW - Entsorgung KW - Kerntechnik KW - Radioaktive Stoffe PY - 2016 SN - 0005-6650 VL - Mai 2016 IS - Band 91 SP - 188 EP - 192 PB - Springer VDI Verlag CY - Düsseldorf AN - OPUS4-36852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank A1 - Droste, Bernhard T1 - Transport von Großkomponenten aus der Stilllegung kerntechnischer Anlagen in Deutschland-Erfahrungen bei der mechanischen Integritätsbewertung N2 - Im Zuge des Rückbaus kerntechnischer Anlagen in Deutschland müssen u. a. Großkomponenten (Dampferzeuger, Reaktordruckbehälter) über öffentliche Verkehrswege in Zwischenlager transportiert werden, in denen sie zerlegt bzw. zwischengelagert werden. Für diese Versandstücke ist eine mechanische Integritätsbewertung, nach den Vorschriften der Internationalen Atomenergie-Organisation (IAEO), notwendig, die in der Regel unter dem Einsatz einer komplexen numerischen Berechnung erfolgt. ---------------------------------------------------------- In the course of decommissioning of power plants in Germany large nuclear components (steam generator, reactor pressure vessel) must be transported over public traffic routes to interim storage facilities, where they are dismantled or stored temporarily. For these packages a safety evaluation considering the International Atomic Energy Agency (IAEA) transport regulations is necessary, preferably by a complex numerical analysis. KW - Radioaktive Stoffe KW - Transport KW - Mechanik KW - Numerische Analyse PY - 2016 SN - 0005-6650 VL - 91 IS - 5 SP - 188 EP - 192 PB - Springer VDI Verlag CY - Düsseldorf AN - OPUS4-36016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank A1 - Schubert, Sven T1 - Neue Regel für das Alterungsmanagement N2 - Die Regelwerksanforderungen für Verpackungen für den Transport radioaktiver Stoffe basieren auf den Empfehlungen der IAEA und werden über die verkehrsträgerspezifischen internationalen Regelwerke in nationales Recht umgesetzt. Um die Anforderungen des Regelwerkes zu erläutern, entwickelt die Bundesanstalt für Materialforschung und -prüfung (BAM) Gefahrgutregeln (BAM-GGR), welche die Entwickler, Hersteller und Betreiber von Behältern über die von der BAM angewandten Verfahren bei der Umsetzung gesetzlicher Bestimmungen informieren und unterstützen sollen. KW - Gefahrgut KW - Radioaktive Stoffe KW - Alterung KW - Transport PY - 2023 VL - 2023 IS - 9 SP - 16 EP - 18 PB - Heinrich Vogel CY - München AN - OPUS4-58577 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -