TY - JOUR A1 - Zoega, A. A1 - Krause, Martin A1 - Kurz, J. A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Boßmann, N. T1 - Ultraschalluntersuchungen zur Rissdetektion an Spannbetonschwellen N2 - Im deutschen Eisenbahnnetz sind ca. 80 Millionen Spannbetonschwellen verbaut. Analog zu anderen Bauwerken werden Wpannbetonschwellen regelmäßig visuell inspiziert. Die Rissbildung ist bei diesen Inspektionen ein Kriterium für die Schädigung einer Spannbetonschwelle. Durch Rissbildung kann es passieren, dass Betonschwellen ihre Nutzungsdauer nicht erreichen. KW - ZfPBau KW - Spannbeton PY - 2017 VL - März 2017 IS - Ernst & Sohn Special 2017 SP - 20 EP - 22 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-48112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Knackmuß, J. A1 - Creutzburg, R. T1 - Comparative visualization of the geometry of a hollow box girder using 3D-Lidar Part 2: Reconstruction of 3D Geometric Modell N2 - With the mandatory introduction of the May 2011 directive for reassessment of bridges in Germany, the administrations of the federal and state governments have the duty to prove the stability of their bridge stock. Verification of bridge stability will be realized with consideration of the newly increased traffic loads. Particularly in older bridges, the verification can only be achieved if calculative surplus load capacity of the original structural design is taken into account in the recalculation. One option for considering these reserves is the exact determination of the dead weight of the bridge. Within this case study, it will be demonstrated how the problem can be practically solved. In order to determine the dead weight of a concrete bridge, its volume has to be calculated. as a first step, a 3D laser scanner is used to record the internal geometry of a hollow box bridge girder. For the determination of the thickness of the concrete member, the non-destructive technique ultrasonic echo is applied. The construction must be segmented in approximately equidistant parts in order to be able to carry out an economic and efficient investigation. The description of the segmentation of the point cloud, carried out in a 2D model, was presented in the first part of the publication. The subject of this presentation is the merging of 2D cross sections into a 3D model, from which the weight of the bridge can be calculated. T2 - IS&T International Symposium on Electronic Imaging 2017 CY - San Francisco, CA, USA DA - 29.01.2017 KW - Zerstörungsfreie Prüfung im Bauwesen KW - LiDAR KW - NDT PY - 2017 AN - OPUS4-39156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Taffe, A. T1 - Istzustandserfassung von Parkbauten mit Betondeckungsmessung und Bewehrungsortung N2 - Der Schutz und die Instandsetzung von Betonbauteilen haben im Bereich von Parkhäusern aufgrund der dort herrschenden Beanspruchungen eine besondere Bedeutung. Wichtigste Voraussetzung für die sachkundige Planung von Instandsetzungsmaßnahmen ist die Ist-Zustandserfassung der betroffenen Betonbauteile. Diese wird üblicherweise mittels einer Kombination aus zerstörungsfreien und zerstörungsarmen Prüfverfahren durchgeführt. Welche Verfahren und Verfahrenskombinationen sind für eine Ist-Zustandserfassung von Betonbauteilen geeignet und haben sich in der Praxis bewährt? Was ist bei ihrer Durchführung zu beachten und wie sind die Prüfergebnisse zu beurteilen? T2 - DBV-Arbeitstagung "Schutz und Instandsetzung von Betonbauteilen - Aktuelle Regelwerke, Istzustandserfassung von Parkbauten" CY - Berlin, Germany DA - 07.12.2017 KW - Zerstörungsfreie Prüfung KW - Parkhaus KW - Istzustandserfassung PY - 2017 AN - OPUS4-43366 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Knackmuß, J. A1 - Creutzburg, R. T1 - Comparative visualization of the geometry of a hollow box girder using 3D-LiDAR – Part 2: Reconstruction of 3D Geometric Model N2 - With the mandatory introduction of the May 2011 directive for reassessment of bridges in Germany, the administrations of the federal and state governments have the duty to prove the stability of their bridge stock. Verification of bridge stability will be realized with consideration of the newly increased traffic loads. Particularly in older bridges, the verification can only be achieved if calculative surplus load capacity of the original structural design is taken into account in the recalculation. One option for considering these reserves is the exact determination of the dead weight of the bridge. Within this case study, it will be demonstrated how the problem can be practically solved. In order to determine the dead weight of a concrete bridge, its volume has to be calculated. as a first step, a 3D laser scanner is used to record the internal geometry of a hollow box bridge girder. For the determination of the thickness of the concrete member, the non-destructive technique ultrasonic echo is applied. The construction must be segmented in approximately equidistant parts in order to be able to carry out an economic and efficient investigation. The description of the segmentation of the point cloud, carried out in a 2D model, was presented in the first part of the publication. The subject of this presentation is the merging of 2D cross sections into a 3D model, from which the weight of the bridge can be calculated. T2 - IS&T International Symposium on Electronic Imaging 2017 CY - San Francisco, CA, USA DA - 29.01.2017 KW - LiDAR KW - Zerstörungsfreie Prüfung KW - Brücken KW - NDT KW - Bridge inspection PY - 2017 U6 - https://doi.org/10.2352/ISSN.2470-1173.2017.6.MOBMU-308 SP - 255 EP - 264 PB - Society for Imaging Science and Technology AN - OPUS4-39242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan T1 - Zerstörungsfrie Prüfungen an Konstruktionen aus Beton - Stand der Technik – Stand der Forschung N2 - Darstellung verschiedener zerstörungsfreier Prüfverfahren des Bauwesens zur Untersuchung von Konstruktionen aus Beton. T2 - Interne Arbeitssitzung der DEGES - 3.T-/KI-Runde CY - Berlin, Germany DA - 21.04.2017 KW - Brücke KW - zerstörungsfreie Prüfung PY - 2017 AN - OPUS4-39904 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Mielentz, Frank A1 - Wiggenhauser, Herbert T1 - Bauwerksüberwachung mit Ultraschall N2 - Übersichtsvortrag zur Bauwerksüberwachung mit Ultraschall mit dem Schwerpunkt auf Materialcharakterisierung. T2 - 23. DEGA Workshop "Physikalische Akustik" CY - Bad Hönnef, Germany DA - 19.10.2017 KW - Ultraschall KW - Beton KW - Zerstörungsfreie Prüfung PY - 2017 AN - OPUS4-42616 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Gründer, Klaus-Peter A1 - Hille, Falk A1 - Liehr, Sascha A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Pirskawetz, Stephan A1 - Rogge, Andreas A1 - Said, Samir A1 - Viefhues, Eva A1 - Zorn, Sebastian ED - Baeßler, Matthias ED - Möller, G. ED - Rogge, Andreas ED - Schiefelbein, N. T1 - Innovative Messsysteme zum Brückenmonitoring am Beispiel einer Versuchsbrücke – vom Sensor bis zur Zustandsprognose N2 - In der aktuellen Projektphase liegt der Fokus auf der Datenaufnahme, -bearbeitung und -speiche-rung mit dem Ziel, automatisierte Auswerteverfahren einsetzen zu können. Aktuell wurden primär punktuelle Messungen an ausgewählten Messtagen aufgenommen. Die Systeme sollen so weiter-entwickelt werden, dass sie sich auch für kontinuierliche Messungen im Rahmen von Monitoring-aufgaben eignen. Ein wichtiger Fokus bei der Auswertung ist die Kombination mit numerischen Modellen, die mithilfe von Bayesian Update Verfahren und den aufgenommenen Messdaten kalibriert und im Verlauf der Monitoringaufgabe angepasst werden sollen. Insbesondere sollen auch zeitabhängige Modelle, die eine zeitliche Entwicklung von Struktureigenschaften beinhalten (Kriechen, Schwinden, Ermüdung, Korrosion) dazu verwendet werden, die zukünftige Performance der Struktur bewerten zu können. Basierend darauf werden dann Konzepte zur Planung von Inspektion und Wartung erstellt. T2 - Messen im Bauwesen 2017 CY - Berlin, Germany DA - 14.11.2017 KW - Brückeninfrastruktur KW - Innovative Messverfahren KW - Stereofotogrammetrie PY - 2017 SN - 978-3-9818270-8-8 VL - 2017/1 SP - 7 EP - 19 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-44306 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -