TY - JOUR A1 - Sklorz, Christian A1 - Otremba, Frank A1 - Balke, Christian T1 - BLEVE performance of fire protection coating systems on dangerous goods tanks in a test fire N2 - How can the risk of a BLEVE be reduced? That is the main question based on different research projects. In various large scale fire tests fire protection coating systems were used of different manufacturers. The degree of the coating as well as the layer thickness and the processing were varied. These experimental configurations were partly tested with and without pressure relief valve. The pressure relief valves were not protected again the thermal Load from the test fire. The ambition is to find a minimum of the thickness from the fire protection coating witch delay a BLEVE up to 90 minutes. Here are given the most interested configurations of tanks in fire and a description of the test-rigs. KW - BLEVE KW - Fire protection coating KW - Isolation KW - Test rigs KW - Large scale fire test PY - 2013 DO - https://doi.org/10.12720/ijmse.1.2.90-93 SN - 2315-4527 VL - 1 IS - 2 SP - 90 EP - 93 PB - Engineering and technology publishing AN - OPUS4-30124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pötzsch, Sina A1 - Krüger, Simone A1 - Sklorz, Christian A1 - Borch, Jörg A1 - Hilse, Thilo A1 - Otremba, Frank T1 - The fire resistance of lightweight composite tanks depending on fire protection systems N2 - To save weight and resources lightweight tanks with complex geometries made of glass-fibre reinforced plastics (GFRP) are a promising innovation for the transportation of dangerous goods. To realise the use of polymer tanks for such applications, their fire safety must be guaranteed. This paper presents solutions to protect fibre-reinforced plastic tanks from fire. The fire resistance of six GFRP tanks with different fire protection systems was tested in an outdoor full-scale fire test facility according to the regulation stipulated in the ADR (European agreement concerning the national carriage of dangerous goods by road). All tanks feature a complex geometry and a holding capacity of 1100 litres. The fire protection systems are composed of specialised resins as well as two intumescent coatings. All systems had a protective impact. The best results were achieved by the epoxy based intumescent coating, which was able to prolong the time needed to reach 150 °C inside the tank by 20 min. The emergence of a temperature holding point inside the tank due to condensation effects was observed at temperatures around 100 °C. KW - Fire safety composite tanks PY - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0379711218301644 DO - https://doi.org/10.1016/j.firesaf.2018.08.007 SN - 0379-7112 SN - 1873-7226 VL - 100 SP - 118 EP - 127 PB - Elsevier Ltd. AN - OPUS4-45697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Iancu, O.T. A1 - Erhard, Anton A1 - Otremba, Frank A1 - Sklorz, Christian T1 - Consistency between analytical and finite element predictions for safety of cylindrical pressure vessels at higher temperatures N2 - Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt. KW - Materials testing KW - FEM KW - Plastic instability KW - Limit load analysis KW - Pressure vessel KW - Analytical solution PY - 2014 SN - 0025-5300 VL - 56 IS - 4 SP - 274 EP - 278 PB - Hanser CY - München AN - OPUS4-30722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konersmann, Rainer A1 - Sklorz, Christian T1 - Zur Früherkennung technischer Risiken N2 - Der Begriff 'Risiko' erzeugt selten positive Emotionen. Risiken mögen wir eigentlich nicht, denn sie können manchmal existenzgefährdend sein. Deshalb möchten wir Risiken so früh wie möglich entdecken. Das rechtzeitige Erkennen riskanter Entwicklungen und Zustände, so die Theorie, ermöglicht es, die 'Stellschrauben' für die Konsequenz und die Eintrittswahrscheinlichkeit, d. h. den beiden Faktoren der Risikoformel, so weit zurückzudrehen, bis uns das verbleibende Restrisiko akzeptabel erscheint. Es besteht aber der begründete Verdacht, dass es manchmal sehr schwierig ist, risikoträchtigen Entwicklungen rechtzeitig entgegen zu wirken, zumal sich Fehlerquellen oft nicht sofort zeigen. Es könnte aber auch sein, dass die Ursachenforschung – aufgrund wirtschaftlicher Erwägungen – nicht konsequent genug betrieben wird. So kann es passieren, dass einzelne Schadensereignisse als unerheblich bewertet werden und kostenintensive Nachbesserungen entbehrlich erscheinen. Der folgende Beitrag beschreibt einige Beispiele zu diesem Thema und versucht eine Antwort darauf zu finden, warum die Früherkennung technischer Risiken bislang so wenig erfolgreich war. KW - Risiko KW - Früherkennung KW - Vorsorgeprinzip PY - 2014 SN - 2191-0073 VL - 4 IS - 6 SP - 45 EP - 50 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-30868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Sklorz, Christian A1 - Widjaja, Martinus Putra A1 - Mair, Georg W. A1 - Seidlitz, Holger T1 - Application of the incremental hole-drilling method for residual stress determination in type 4 pressure vessels N2 - Hole-drilling method is a standardized technique for obtaining residual stresses in isotropic structures. Previous studies provide a foundation that enables the use of this method to investigate orthotropic structures, such as fiber-reinforced composites. In this study, the incremental hole-drilling method was applied to investigate residual stresses in filament wound type 4 composite pressure vessels. The investigated composite cylinders were manufactured with different internal pressure functions during the winding process, to achieve distinct residual stress states. Additionally, the influence of the initial loading under sustained internal pressure and increased temperature on the stress distribution was investigated. It was shown that the residual stress state can be influenced by varying the internal pressure in the winding process. After testing at sustained load and increased temperature, a stress redistribution was observed, which took place due to creep phenomena. Finally, a discussion of the challenges for the application of the hole-drilling method to composite pressure vessels is provided. KW - Hole-drilling method KW - Filament winding KW - Type 4 composite pressure vessels KW - Residual stresses KW - Stress redistribution PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627765 DO - https://doi.org/10.1515/mt-2024-0328 SN - 2195-8572 VL - 67 IS - 4 SP - 663 EP - 674 PB - Walter de Gruyter GmbH AN - OPUS4-62776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -