TY - JOUR A1 - Berger, Wolfgang A1 - Bandow, Nicole A1 - Simon, Franz-Georg T1 - Untersuchungen zum Merkmalstransfer bei der Behandlung von Hausmüllverbrennungsasche N2 - In Deutschland fallen aktuell über 5 Mio. Tonnen Hausmüllverbrennungsaschen (HMVA) pro Jahr an. Aus diesen werden nur ca. 8 % Metalle (davon ca. 1 % NE-Metalle) zurückgewonnen. Zur Beurteilung des Wertstoffpotentials werden die HMVA nach standardisierten Vorschriften beprobt, für die Analytik vorbehandelt/vorbereitet/aufgearbeitet und auf ihre Inhaltsstoffe analysiert. Im nachfolgenden Beitrag wird der Schwerpunkt auf die Probenvorbehandlung und -vorbereitung gelegt, wobei der Merkmalstransfer von der Ausgangs-(Feld-)Probe über die Laborprobe und die Prüfprobe bis zur Mess-(Analysen-) Probe am Beispiel von NE-Metallen einer nassaufbereiteten HMVA untersucht wurde. Die Ergebnisse wurden mit Hilfe statistischer Methoden bewertet. Die Ergebnisse zeigen, dass die Verteilung der NE-Metalle in den einzelnen Schritten der Probenbehandlung elementspezifisch ist. Bei Blei ist ein Erhalt der Merkmalsverteilung über alle Behandlungsschritte erkennbar. Bei Kupfer nehmen die Konzentrationen in den aufeinander folgenden Behandlungsschritten deutlich ab. Die Ursache könnte das in der Feinfraktion enthaltene metallische Kupfer mit seinen spezifischen Eigenschaften sein. ------------------------------------------------------------------------------------------------------------------------------------------- More than 5 billion tons of municipal solid waste incineration bottom ashes (MSWI BA) are generated by incineration per year in Germany. Currently only 8 % of metals (of these 1 % are non-ferrous metals) are recovered from MSWI BA. For characterization of recovery potential, MSWI BA samples have to be taken, pre-treated and analyzed according to standardized methods. This manuscript focuses on sample pre-treatment and preparation of a MSWI BA sample aiming to investigate the characteristics transfer over the process of sub-sampling from the original (field) sample to the laboratory sample, test sample until the analytical sample. All results have been evaluated with statistical methods. The results show that influence of each single pre-treatment and preparation step on metal content differs for the individual metals. For lead a conservation of characteristics distribution can be observed, while for copper a continuous decline of solid concentration is observed over all preparation steps. One possible reason may be the fact that copper is mainly contained in the fine fraction as metallic copper with specific properties. KW - Hausmüllverbrennungsasche KW - Probenvorbehandlung und -vorbereitung KW - Merkmalstransfer KW - NE-Metalle KW - Statistische Auswertung PY - 2015 SN - 0027-2957 SN - 1863-9763 VL - 1 SP - 22 EP - 26 PB - Erich Schmidt CY - Berlin AN - OPUS4-32566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Berger, Wolfgang ED - Litz, N. ED - Wilcke, W. ED - Wilke, B.-M. T1 - Thermische Bodenbehandlung KW - Bodenbehandlung KW - Desorption KW - Pyrolyse KW - Verbrennung PY - 2008 SN - 978-3-527-32341-8 IS - Abschnitt IV-3.1.2 SP - 1 EP - 11 PB - Wiley-VCH CY - Weinheim AN - OPUS4-18185 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwarz, Wolfram A1 - Simon, Wolfgang T1 - Untersuchungen zum elektrochemischen Verhalten des Eisens in Alkalilösung PY - 1963 SN - 0005-9021 VL - 67 IS - 1 SP - 108 EP - 117 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-10294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pagel, H.-J. A1 - Schwarz, Wolfram A1 - Simon, Wolfgang T1 - Gas circulating pump for enclosed systems PY - 1958 SN - 0950-7671 VL - 36 SP - 53 PB - Institute of Physics and the Physical Society CY - London AN - OPUS4-7820 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Döring, Joachim A1 - Stark, Wolfgang A1 - Bartusch, Jürgen A1 - Mc Hugh, Jarlath A1 - Simon, W. T1 - Ultraschall-Prozesskontrolle mechanischer Parameter von aushärtenden Polymeren - Inline-Sensorik für die Herstellung von Kunststoffkomponenten KW - Aushärtung KW - Ultraschall KW - Sensoren KW - Materialparameter PY - 2007 SN - 0025-5300 VL - 49 IS - 5 SP - 238 EP - 242 PB - Hanser CY - München AN - OPUS4-14976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg A1 - Eckardt, Jürgen A1 - Christoph, Gabriele T1 - Results of interlaboratory comparisons of column percolation tests N2 - Laboratory leaching tests may be used for source term determination as a basis for risk assessment for soil–groundwater pathway (leachate forecast) on contaminated sites in Germany. Interlaboratory comparisons on the evaluation of the reproducibility of column percolation tests were conducted within the framework of an integrated R + D program using three waste reference materials. The interlaboratory comparisons of column percolation tests showed good reproducibility of the results for inorganic and organic parameters as well as for the accompanying parameters. This is due to the stipulations concerning the time of contact between leachant and sample material as well as the sample placement in the columns. Different column dimensions used by the participants of the interlaboratory comparisons did not have any substantial influence on the column test results. KW - Leachate forecast KW - Column percolation tests KW - Interlaboratory comparisons KW - Contaminated soil KW - Waste material PY - 2007 DO - https://doi.org/10.1016/j.jhazmat.2007.03.039 SN - 0304-3894 VL - 148 IS - 3 SP - 714 EP - 720 PB - Elsevier CY - Amsterdam AN - OPUS4-15754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Berger, Wolfgang A1 - Mantyk, Matthias T1 - Rückgewinnung von Kupfer aus Rostaschen aus der thermischen Abfallbehandlung KW - Flotation KW - Ressourcen KW - Rostasche PY - 2007 SN - 0026-0746 VL - 61 IS - 11 SP - 713 PB - Giesel Verlag GmbH CY - Isernhagen AN - OPUS4-16122 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Holm, Olaf A1 - Berger, Wolfgang T1 - Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling N2 - Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources. KW - Flotation KW - Cadmium KW - Tellurium KW - Thin film technology KW - Sand blasting PY - 2013 DO - https://doi.org/10.1016/j.wasman.2012.12.025 SN - 0956-053X VL - 33 IS - 4 SP - 942 EP - 947 PB - Pergamon Press CY - New York, NY AN - OPUS4-29312 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Durchführung von Ringversuchen zur Validierung der Normen E DIN 19528 und E DIN 19529 N2 - Um den Erfordernissen des Grundwasser- und Bodenschutzes zu entsprechen ist die Kenntnis des Elutionsverhaltens von Abfall- und Bodenmaterialien erforderlich, wenn diese z.B. zur Verwertung im Straßen- oder Landschaftsbau vorgesehen sind. Im Zusammenhang mit der Novellierung der Bundes-Bodenschutzverordnung und der Einführung der Ersatzbaustoffverordnung sowie in Auswertung der Ergebnisse des BMBF-Verbundvorhabens „Sickerwasserprognose“ wurden vom DIN-Normenaus-schuss Wasserwesen, Unterausschuss „Eluierungsverfahren“ zwei Verfahren zur Elution von Fest-stoffen erarbeitet, die im Oktober 2007 als Entwürfe veröffentlicht wurden. Dabei handelt es sich um ein Säulenperkolationsverfahren zur gemeinsamen Untersuchung des Elutionsverhaltens von orga-nischen und anorganischen Stoffen (E DIN 19528) und ein Schüttelverfahren mit einem Wasser-/ Feststoff-Verhältnis (W/F) von 2 l/kg zur Untersuchung der Elution von anorganischen Stoffen (E DIN 19529). Beide Verfahren sind für Bodenmaterialien und mineralische Abfälle mit einer Korngröße bis 32 mm vorgesehen. Für Normen die in Verordnungen zitiert werden sollen, ist eine Verfahrensvalidierung erforderlich. Im Rahmen dieses Vorhabens waren die Verfahrenskenndaten auf der Grundlage von Ringversuchen zu ermitteln. Zunächst wurden vier für die Verordnungen relevante Materialien (Hausmüllverbrennungs-asche, Recyclingbaustoff, Bodenmaterial, Stahlwerksschlacke) als Referenzmaterialien (RM) aufberei-tet. Die zu analysierenden Parameter wurden unter Berücksichtigung der Regelungsrelevanz in Abstimmung mit dem Auftraggeber ausgewählt. Die RM wurden gemeinsam mit Referenzlösungen an die 53 Teilnehmer der Ringversuche ausgegeben. Die statistische Auswertung der Ringversuchsergebnisse erfolgte nach DIN 38402-42, wobei der Gesamtmittelwert aller Teilneh-mer als Sollwert herangezogen wurde. Es konnte gezeigt werden, dass akzeptable Reproduzierbarkeiten für organische und anorganische Schadstoffe durch geeignete Vorgaben sowohl für Schütteltests als auch für Säulenversuche erzielt werden können. Dies gilt insbesondere unter Berücksichtigung des breiten Korngrößenspektrums der RM, der relativ hohen zugelassenen Toleranzen für das W/F bei den Säulenversuchen und des kurzen Bekanntheitsgrades der Normenentwürfe. Die ermittelten Verfahrenskenndaten finden Eingang in die abschließende Bearbeitung der Normen. KW - Verwertung KW - Abfallmaterialien KW - kontaminierter Boden KW - Auslaugungsverhalten KW - Eluierungsverfahren KW - Schütteltest KW - Säulenperkolationsversuch KW - Sickerwasserprognose KW - Standardisierung KW - Validierung KW - Ringversuche PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-354756 SP - 1 EP - 275 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35475 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lopez Meza, Sarynna A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Harmonization and validation of leaching standards - new developments in Germany N2 - This article presents a snapshot of key issues regarding characterization of granular waste materials with respect to their reuse as alternative construction materials, and the factors that need to be considered in their reutilization in order to comply with soil and groundwater protection regulations. KW - Column tests KW - Granular materials KW - Leaching protocols KW - Standardisation KW - Waste PY - 2008 DO - https://doi.org/10.2462/09670513.890 SN - 0967-0513 VL - 16 IS - 1 SP - 45 EP - 49 PB - EPP Publ. CY - Richmond AN - OPUS4-17376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Analytik für Ersatzbaustoffe KW - Ersatzbaustoffe KW - Auslaugverfahren KW - Säulentest PY - 2008 SN - 0344-1733 SN - 1610-8256 VL - 32 IS - 9 SP - 26 EP - 28 PB - Vogel CY - Würzburg AN - OPUS4-17978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg A1 - López Meza, S. T1 - Leaching experiments on the release of heavy metals and PAH from C&D waste and MSWI bottom ash N2 - Leaching tests are fundamental tools for the assessment of long-term impact of contaminated waste materials on the soil-groundwater pathway. Waste materials should be tested under conditions equal to their actual application in re-use scenarios to achieve reliable results. Since the standards for leaching procedures available on international level so far are either not validated or considered inadequate in respect to coarse grained materials, new standards had to be developed. Therefore column percolation and batch test procedures have been standardized and validated to enable their introduction to new German regulations concerning waste management. Practical aspects of the test procedures as well as the boundary conditions compared to the already existing standards will be described. Examples including round robin test results will be given to justify the selection of the new specifications. T2 - 2nd International conference on hazardous and industrial waste management CY - Chania, Crete, Greece DA - 2010-10-05 KW - Leaching KW - Bioavailability KW - Column tests KW - Batch tests PY - 2010 IS - Session A, A5.1. SP - 1 EP - 8 AN - OPUS4-22128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Source term determination by leaching procedures - new developments in Germany T2 - Global waste management symposium CY - San Antonio, TX, USA DA - 2010-10-03 KW - Elutionsverfahren KW - Abfall PY - 2010 SP - 1 EP - 11(?) AN - OPUS4-22256 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Praktische Aspekte der Anwendung von Eluierungsverfahren nach DIN 19528 und DIN 19529 N2 - Im Zusammenhang mit der Novellierung der Bundes-Bodenschutzverordnung und der Einführung einer Ersatzbaustoffverordnung wurden vom DIN-Normenausschuss Wasserwesen, Unterausschuss "Eluierungsverfahren" zwei Verfahren zur Elution von Feststoffen erarbeitet. Dabei handelt es sich um ein Säulenperkolationsverfahren zur gemeinsamen Untersuchung des Elutionsverhaltens von organischen und anorganischen Stoffen und ein Schüttelverfahren mit einem Wasser-/Feststoff-Verhältnis (W/F) von 2 l/kg zur Untersuchung der Elution von anorganischen Stoffen. Beide Verfahren sind für Bodenmaterialien und mineralische Abfälle mit einer Korngröße bis 32 mm vorgesehen. Der Vergleich der Praktikabilität der beiden Elutionsverfahren soll zur Diskussion zu deren Einsatz im Rahmen der geplanten bundeseinheitlichen gesetzlichen Regelungen beitragen, welche gegenwärtig kontrovers geführt wird. KW - Kontaminierter Boden KW - Abfall KW - Eluierungsverfahren KW - Säulenversuche KW - Schüttelversuche KW - Quellstärkeermittlung KW - Leaching KW - Contaminated soil KW - Mineral waste KW - Column test KW - Batch test KW - Legislation PY - 2009 SN - 0942-3818 SN - 1864-8371 VL - 18 IS - 1 SP - 5 EP - 10 PB - Schmidt CY - Berlin AN - OPUS4-18947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Results of German ring tests on the vaildation of leaching standards for source term determination T2 - WASCON 2009 - Sustainable management of waste and recycled materials in construction CY - Lyon, France DA - 2009-06-03 KW - Ringversuche KW - Validierung Normen KW - Kontaminierter Boden KW - Abfall KW - Säulenversuche KW - Schüttelversuche PY - 2009 SP - 1 EP - 10(?) AN - OPUS4-19569 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Eckardt, Jürgen A1 - Simon, Franz-Georg T1 - Evaluation of leaching and extraction procedures for soil and waste N2 - Laboratory leaching tests may be used for source term determination as a basis for risk assessment for soil–groundwater pathways on contaminated sites. In order to evaluate different leaching procedures, batch extraction tests and percolation tests were performed using three reference materials produced from contaminated soil, demolition waste and municipal solid waste incinerator bottom ash. Emphasis was placed on the investigation of the leachability of the heavy metals copper and chromium, polycyclic aromatic hydrocarbons (PAHs) and the anions chloride and sulfate. Significant discrepancies between column experiments and batch/extraction tests were found for the release of PAHs and to a lesser extent for the heavy metals Cu and Cr. Additionally interlaboratory comparisons were conducted based on different leaching tests with the reference materials and evaluated using the criteria of comparability and reproducibility. The best reproducibility was achieved for all investigated substances in column tests. The reproducibility of batch tests was acceptable except for PAHs. The results from the experimental work will help establish standardized and feasible laboratory procedures as fundamental for substance specific risk assessment of contaminated sites. KW - Leaching procedures KW - Leachate prognosis KW - Source term determination KW - Risk assessment KW - Contaminated soil KW - Waste materials PY - 2008 DO - https://doi.org/10.1016/j.wasman.2007.03.008 SN - 0956-053X VL - 28 IS - 6 SP - 1027 EP - 1038 PB - Pergamon Press CY - New York, NY AN - OPUS4-17191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Kalbe, Ute A1 - Berger, Wolfgang ED - Milind V. Khire, ED - Alshawabkeh, Akram N. ED - Krishna R. Reddy, T1 - Waste characterization by leaching and extraction procedures KW - Leaching KW - Heavy metal release KW - Bottom ash PY - 2008 SN - 978-0-7844-0970-1 VL - 177 IS - Geotechnical Special Publication SP - 676 EP - 683 AN - OPUS4-17217 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg A1 - Lopez Meza, Sarynna T1 - Leaching experiments on the release of heavy metals and PAH from soil and waste materials N2 - Leaching tests are fundamental tools for the assessment of long-term impact of contaminated waste materials on the soil-groundwater pathway. Experiments were carried out in the framework of standardization and validation of column percolation and batch test procedures, in particular concerning the stipulation of the experimental setup. The colloid release of column and batch experiments was compared and the influence of different column filling heights (12.5–50 cm) on the release of polycyclic aromatic hydrocarbons (PAH) from soil was studied, as well as the effect of varying contact times (2.5–16 h) on the release of chromium from construction and demolition (C&D) waste and municipal solid waste incineration (MSWI) bottom ash. The results indicate that filtration of the eluate, which is required for batch tests, does not always allow the simulation of the actual colloid amount in soil pore water. Medium column heights four times the inner diameter of the column seemed to provide reasonable equilibrium adjustment conditions and avoid major biodegradation. The release of chromium was only marginally affected by the contact time, varied between 0.115 and 0.150 mg/kg for demolition waste eluate at a liquid-to-solid ratio of approximately 5 L/kg. KW - Column tests KW - Batch tests KW - Waste materials KW - Leaching KW - Standardization PY - 2012 DO - https://doi.org/10.1016/j.jhazmat.2011.02.016 SN - 0304-3894 VL - 207-208 SP - 51 EP - 55 PB - Elsevier CY - Amsterdam AN - OPUS4-24030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lopez Meza, Sarynna A1 - Kalbe, Ute A1 - Berger, Wolfgang A1 - Simon, Franz-Georg T1 - Effect of contact time on the release of contaminants from granular waste materials during column leaching experiments N2 - When reusing or disposing of contaminated granular waste materials there is a need to evaluate how the contaminants will interact on the pathway soil-groundwater and the effect this interaction will have on the surrounding environment. While column testing can provide a closer approximation to field percolation conditions than batch testing, there is still a need to develop column testing procedures that consider the requirements of practical testing time frames. This study evaluates the effect of different column contact times (2.5, 5, and 16 h) on the release of inorganic constituents from bottom ash and demolition waste, two commonly reused granular materials. Leaching data for representative constituents of concern, such as copper, chromium, sulfate and chloride, as well as pH and electrical conductivity was compared for all different contact times studied. Results for the materials investigated in this study showed that variations in contact time have no significant effect on the release of the selected constituents and leaching parameters at low liquid to solid ratios. However, after a liquid to solid ratio of 1 L/kg, the effect is more noticeable, and higher contact times show lower pH values as well as a reduction in the release of constituents of concern from bottom ash. In the case of demolition waste, the variation of contact time did not have a strong effect on the leaching behavior. KW - Leaching procedures KW - Standardisation KW - Column tests KW - Contact time KW - Granular materials KW - Waste PY - 2010 DO - https://doi.org/10.1016/j.wasman.2009.11.022 SN - 0956-053X VL - 30 IS - 4 SP - 565 EP - 571 PB - Pergamon Press CY - New York, NY AN - OPUS4-20934 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schröder, Simon Alexander A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Stephan, Ina A1 - Hohmann, Gloria A1 - Ziegert, Christof T1 - Identifikation und Einordnung von historischen Lehmbauteilen für die Wiederverwendung hinsichtlich Anreicherung von Schadstoffen und bauschädlichen Salzen T1 - Identification and classification of historical earth construction elements for recycling in respect of accumulation of pollutants and structurally damaging salts N2 - Lehmbaustoffe, einschließlich Lehm aus dem historischen Baubestand, bieten ein hohes Potenzial für ihre Wiederverwendbarkeit und die Schonung natürlicher Ressourcen. Zur Bewertung des Wiederverwendungspotenzials gibt es nur wenige Studien hinsichtlich der Schadstoffbelastung und der Anreicherung von Salzen in Gebäuden aus dem historischen Bestand. Tonminerale, die in Lehmbaustoffen als Bindemittel fungieren, können Schadstoffe binden. Die Region Mitteldeutschland ist geprägt durch jahrzehntelange Einwirkung erheblicher Schadstoffemissionen aus der Chemie- und Braunkohleindustrie. Der Eintrag von Schadstoffen in Lehmbaustoffe ist außerdem aus geogenen Hintergrundbelastungen denkbar, z. B. in Auenböden beeinflusst durch Einträge aus dem Erzbergbau. Salzbildende Anionen wie Chloride oder Nitrate können aufgrund ihrer hohen Löslichkeit mittels kapillarer Kräfte durch die Porenstruktur transportiert werden. In Lehmwänden können sie vor allem in oberflächennahen Lagen, in denen höhere Verdunstungsraten vorherrschen, durch Bindung mit in Lösung vorliegenden oder baustoffeigenen Kationen auskristallisieren und bauschädliche Salze ausbilden. Auch durch spezifische Nutzungen akkumulierte Schadstoffe, z. B. durch die Einwirkung von Tabakrauch, könnten theoretisch einer Wiederverwendung von Lehm entgegenstehen. In Anbetracht der Herausforderungen hinsichtlich der klimatischen und gesellschaftlichen Veränderungen, sind wissenschaftliche Erkenntnisse im Lehmbau erforderlich, die eine Integration in eine nachhaltige Kreislaufwirtschaft ermöglichen. Bei bisherigen Gesetzgebungsverfahren zu rezyklierten Baustoffen wurden Lehmbaustoffe noch nicht berücksichtigt. Ziel einer Vorstudie im Rahmen der WIR!-Initiative GOLEHM ist die Überprüfung der Wiederverwendbarkeit Wiederverwendbarkeit von Lehmbaustoffen aus historischen Bauten an Stichproben hinsichtlich der Umwelt- und Nutzerverträglichkeit. Für den Raum Mitteldeutschland können damit Anhaltspunkte darüber gegeben werden, welche Schadstoffe und bauschädlichen Salze in welchem Maße in Lehmbaustoffen aus dem Gebäudebestand erwartet werden können. Daraus können Hinweise zum Umgang mit Lehmbaustoffen aus historischen Gebäuden abgeleitet werden. Darüber hinaus wurden exemplarisch an zwei Gebäuden mikrobiologische Untersuchungen zur Ermittlung einer möglichen Belastung mit Schimmelpilzen vorgenommen. N2 - Earth construction materials, including earth from historical building stock, offer high potential in terms of their recyclability and sparing use of natural resources. Yet, only a few studies have been conducted on the levels of pollutants and the accumulation of salts in buildings from the historical building stock to enable an assessment of the potential for recycling. The aim of a preliminary study as part of the GOLEHM Initiative from WIR! is to use spot checks to review the recyclability of earth construction materials from historical buildings in terms of environmental impact and tolerance by users. This could provide indicators for the Central Germany region on which pollutants and structurally damaging salts can be expected in earth construction materials from the building stock and to what extent, allowing conclusions to be drawn on how to manage earth construction materials from historical buildings. Additionally, microbiological inspections of two sample buildings were performed to assess a potential contamination with mould. T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Wiederverwendung KW - Kreislaufwirtschaft KW - Schadstoffe KW - Bauschädliche Salze PY - 2024 SP - 1 EP - 8 CY - Weimar AN - OPUS4-61883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Berger, Wolfgang T1 - Recovery of scarce metals from end-of-life photovoltaic modules N2 - Photovoltaics (PV) is a promising technology for renewable energy sources. In recent years the annual production of PV modules has been growing steadily reaching a total capacity of over 50GWp installed within the EU in 2011. Thin film technology (cadmium telluride CdTe or copper indium diselenide/disulphide CIS) is growing in importance due to its low production costs and the low energy and materials demands during production. However, the prices for the rare materials indium and tellurium will continue to increase. With the expected strong rise of the demand for thin film PV odules, recycling of indium and tellurium will become more important in the future. Within the EU-LIFE project RESOLVED (Recovery of Solar Valuable Materials, Enrichment and Decontamination) the feasibility of sustainable photovoltaic thin film module recycling by means of wet-mechanical processes was demonstrated by BAM Federal Institute for Materials Research and Testing, together with industry partners First Solar Inc and Deutsche Solar AG. T2 - Resources that Don’t Cost the Earth - Encouraging European Collaboration and Solutions - Workshop CY - Berlin, Germany DA - 01.12.2011 KW - Resources KW - Photovoltaics KW - Recycling PY - 2012 UR - https://www.rsc.org/images/Resources-that-dont-cost-the-earth_tcm18-223030.pdf SP - 18 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-26834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Berger, Wolfgang A1 - Simon, Franz-Georg A1 - Weimann, Karin A1 - Alsema, E. A. T1 - A novel approach for the recycling of thin film photovoltaic modules N2 - A sustainable recycling of photovoltaic (PV) thin film modules gains in importance due to the considerable growing of the PV market and the increasing scarcity of the resources for semiconductor materials. The paper presents the development of two strategies for thin film PV recycling based on (wet) mechanical processing for broken modules, and combined thermal and mechanical methods for end-of-life modules. The feasibility of the processing steps was demonstrated in laboratory scale as well as in semi-technical scale using the example of CdTe and CIS modules. Pre-concentrated valuables In and Te from wet mechanical processing can be purified to the appropriate grade for the production of new modules. An advantage of the wet mechanical processing in comparison to the conventional procedure might be the usage of no or a small amount of chemicals during the several steps. Some measures are necessary in order to increase the efficiency of the wet mechanical processing regarding the improvement of the valuable yield and the related enrichment of the semiconductor material. The investigation of the environmental impacts of both recycling strategies indicates that the strategy, which includes wet mechanical separation, has clear advantages in comparison to the thermal treatment or disposal on landfills. KW - Recycling KW - Photovoltaic KW - Thin film modules KW - CdTe KW - CIS KW - Mechanical processing KW - Life cycle analysis PY - 2010 DO - https://doi.org/10.1016/j.resconrec.2009.12.001 SN - 0921-3449 VL - 54 IS - 10 SP - 711 EP - 718 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-21439 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -