TY - JOUR A1 - Vierneusel, B. A1 - Schneider, Thomas A1 - Tremmel, S. A1 - Wartzack, S. A1 - Gradt, Thomas T1 - Humidity resistant MoS2 coatings deposited by unbalanced magnetron sputtering N2 - MoS2 is a suitable solid lubricant for environments free of oxygen or water vapor (i.e. vacuum). Humid air degrades film properties due to oxidation accompanied by high wear and increasing coefficients of friction. The present study aims at the further development of sputtered pure MoS2 coatings, extending their applicability to varying environmental conditions by increasing the resistance against humidity. The systematic coating development process is supported by using an experimental Box–Behnken design with variations of the deposition parameters cathode voltage, target/substrate distance, temperature and argon gas pressure. In contrast to common one-factor-at-a-time (OFAT) studies, this approach enables a determination of interactions between deposition process parameters and tribological–mechanical MoS2 film properties. The tribological improvement focuses on a maximization of wear resistance in air and vacuum measured in ball-on-disk experiments. The evaluated mechanical properties are hardness, elastic modulus and residual stresses. These stresses were determined by the substrate curvature method. The study reveals that the residual stress state in the films and the hardness-to-modulus ratio are crucial for their tribological performance in humid air and vacuum environments. After a detailed determination of the relationships between deposition conditions and film properties, some selected microstructural analyses are presented which show that a substantially basal orientation of the lattice has positive effects on wear but also causes anisotropic film properties which result in fissile fracture of the coating if strong shock or point loads occur. KW - Unbalanced magnetron sputtering KW - MoS2 KW - Humidity resistance KW - Residual stress PY - 2013 DO - https://doi.org/10.1016/j.surfcoat.2013.07.019 SN - 0257-8972 VL - 235 SP - 97 EP - 107 PB - Elsevier B.V. AN - OPUS4-29729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Technische Prüfvorschriften für Fahrbahnübergänge aus Asphalt, TL/TP-ING - Teil 6, Abschnitt 7 N2 - Technische Lieferbedingungen und Technische Prüfvorschriften für Ingenieurbauten KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-343-3 VL - 780/3 SP - 1 EP - 26 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56218 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Technische Lieferbedingungen für die Baustoffe zur Herstellung von Fahrbahnübergängen aus Asphalt (TL ING, Teil 6, Abschnitt 7) N2 - TL BEL-FÜ Technische Lieferbedingungen für die Baustoffe zur Herstellung von Fahrbahnübergängen aus Asphalt TL/TP-Ing - Teil 6, Abschnitt 7 Technische Lieferbedingungen und Technische Prüfvorschriften für Ingenieurbauten KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-342-6 VL - 780/2 SP - 1 EP - 20 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Thomas A1 - Vierneusel, B. A1 - Gradt, Thomas A1 - Tremmel, S. A1 - Wartzack, S. A1 - Szücs, Z. A1 - Arendt, I. T1 - Optimierte MoS2-PVD-Schichten für wechselnde Umgebungsbedingungen N2 - Der Festschmierstoff Molybdändisulfid ist insbesondere für Extremanwendungen, bei denen konventionelle Öl- oder Fettschmierung nicht in Frage kommen (Vakuum, hohe Pressungen) ein gerne eingesetzter Werkstoff. Problematisch ist jedoch der negative Einfluss von Feuchtigkeit, wodurch die Einsetzbarkeit von M0S2 unter Normalbedingungen leidet. Bei mittels PVD-Verfahren abgeschiedenen MoSa-Schichten ergibt sich jedoch die Möglichkeit, durch Anpassung der Beschichtungsparameter vorwiegend basal ausgerichtete Schichten herzustellen, die auch an normal feuchter Luft ein verbessertes tribologisches Verhalten zeigen. MoSa-Schichten sind darüber hinaus auch für Anwendungen bei extrem tiefen Temperaturen interessant, da hier kein Schmierstoff zur Verfügung steht, der ähnlich günstige Reibeigenschaften aufweist. Für bewegliche Stützelemente zwischen supraleitenden Magnetspulen des Kernfusions-Experiments Wendelstein 7-X waren bis zu 7 pm dicke Schichten entwickelt worden, die jedoch durch das notwendige langsame Aufwachsen für andere Anwendungen nicht wirtschaftlich herzustellen waren. Hier sollen neue, im Rahmen eines Kooperationsprojekts entstandene MoS2-PVD-Schichten vorgestellt werden, die bei wechselnden Umgebungsbedingungen noch gute tribologische Eigenschaften liefern, jedoch durch ihre Dicke von 1-2 pm und hoher Aufwachsrate kostengünstig sind. N2 - The solid lubricant molybdenum disulfide is a well known material for extreme conditions where conventlonal oll or grease lubrication is not feasible (vacuum, high pressures). Problems arise due to a negative effect of humidity which is a drawback for the suitability of M0S2 under normal conditions. However, by using a PVD process, Deposition parameters can be optimized to gain coatings with a more textured structure orienting the basal planes parallel to the Substrate surface. Therefore, an improved tribological behavior even under moist conditions can be achieved. MoS2-coatings additionally are interesting candidates for being applied under cryogenic temperatures, since no lubricant is available having similarly favorable frictional properties. Up to 7 pm thick coatings have been developed especially for sliding support elements between superconducting magnets of the fusion-experiment Wendelstein 7-X, however, the extremely slow deposition rate precluded its utilization on more common tribo-systems due to cost considerations. Here, new MoS2-coatings are presented which were developed in a cooperational project, giving good tribological results under variing environments but are more cost effective being only 1-2 pm in thickness and faster in film growth.. T2 - 53. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß CY - Göttingen, Germany DA - 24.09.2012 PY - 2012 SN - 978-3-00-039201-6 SP - 46/1 EP - 46/12 CY - Aachen AN - OPUS4-26724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hickel, Tilmann A1 - Divinski, S. A1 - Starikov, S. A1 - Soisson, F. A1 - Mény, C. A1 - Hegde, O. A1 - Gerlitz, M. A1 - Magnifouet, G. A1 - Schneider, A. A1 - Barreteau, C. A1 - Mirebeau, I. A1 - Tran, V.T. A1 - Förster, G. A1 - Front, A. A1 - Egorov, A. A1 - Wilde, G. A1 - Amara, H. A1 - Hammerschmidt, T. A1 - Mrovec, M. A1 - Pierron-Bohnes, V. A1 - Drautz, R. A1 - Fu, C. T1 - Magnetism in iron alloys: methodological advances for thermodynamics, defects, and kinetics N2 - Steels are among the technologically and economically most relevant materials. Key innovations in important sectors of human society such as mobility, energy and safety, are currently based on alloying of Fe with other transition-metal elements such as Mn, Cr, or Co. Due to strong impacts and conceptual challenges related to magnetism, however, the fundamental understanding and the ability to computationally design these steels in high-throughput approaches lags behind other classes of alloys. In this article, we will provide a substantial review of the role of magnetism, magnetic excitations and transformations for alloy thermodynamics, point defects, interfaces and kinetics. This will be achieved by combining insights from different methods: Ab initio simulations have the advantage that the magnetic ground state is intrinsic part of the electronic minimization. Due to the coarsening of the many-electron structures and therewith magnetic interactions, tight-binding methods can handle larger system sizes. Effective interaction models provide the freedom to exploit more sophisticated magnetic interactions. The performance of these methods in terms of magnetic properties of Fe alloys will be evaluated by providing state-of-the-art results for their sensitivity to magnetism. Furthermore, dedicated experiments will be discussed to complete the understanding of magnetic effects in Fe alloys and to validate the modeling strategy. KW - Magnetic excitations KW - Defects KW - Diffusion KW - Density functional theory KW - Tight-binding KW - Effective interaction models PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634530 DO - https://doi.org/10.1515/ijmr-2023-0225 SN - 1862-5282 VL - 60 IS - 99 SP - 1 EP - 14761 PB - Walter de Gruyter GmbH AN - OPUS4-63453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Zusätzliche Technische Vertragsbedingungen und Richtlinien für Ingenieurbauten, Teil 6: Bauwerksausstattung, Abschnitt 7: Fahrbahnübergänge N2 - Die Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Ingenieurbauten (ZTV-ING) wurden zuletzt mit ARS Nr. 23/2021 vom 20. 10. 2021 mit dem Stand 2021/10 fortgeschrieben. Die jetzige Fortschreibung beinhaltet eine Gliederungsänderung des Regelwerks, um die für den Brückenbau relevanten Teile vorne gebündelt darstellen zu können. Eine Synopse hierzu ist der Anlage 4 zu entnehmen. „Wesentliche Änderungen in den ZTV-ING“ gegenüber der letzten Fassung sind der Anlage 3 zu entnehmen. In gleicher Weise sind die aktuellen „Hinweise zu den ZTV-ING — Stand 2022/01“ gemäß Anlage 2 einzubeziehen. Die Hinweise zu den entsprechenden Abschnitten der ZTV-ING sind bei der Projektbearbeitung und Ausschreibung zu beachten. Soweit die „Hinweise zu den ZTV-ING“ für die jeweilige Maßnahme zutreffend sind und vertragsrechtliche Bedeutung haben, sind entsprechende Textpassagen gesondert in die Vergabeunterlagen aufzunehmen bzw. zu vereinbaren. KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-344-0 VL - 782/7 SP - 1 EP - 30 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mi, W. A1 - Josephs, R. D. A1 - Melanson, J. E. A1 - Dai, X. A1 - Wang, Y. A1 - Zhai, R. A1 - Chu, Z. A1 - Fang, X. A1 - Thibeault, M.-P. A1 - Stocks, B. B. A1 - Meija, J. A1 - Bedu, M. A1 - Martos, G. A1 - Westwood, S. A1 - Wielgosz, R. I. A1 - Liu, Q. A1 - Teo, T. L. A1 - Liu, H. A1 - Tan, Y. J. A1 - Öztuğ, M. A1 - Saban, E. A1 - Kinumi, T. A1 - Saikusa, K. A1 - Schneider, Rudolf A1 - Weller, Michael G. A1 - Konthur, Zoltán A1 - Jaeger, Carsten A1 - Quaglia, M. A1 - Mussell, C. A1 - Drinkwater, G. A1 - Giangrande, C. A1 - Vaneeckhoutte, H. A1 - Boeuf, A. A1 - Delatour, V. A1 - Lee, J. E. A1 - O'Connor, G. A1 - Ohlendorf, R. A1 - Henrion, A. A1 - Beltrão, P. J. A1 - Naressi Scapin, S. M. A1 - Sade, Y. B. T1 - PAWG Pilot Study on Quantification of SARS-CoV-2 Monoclonal Antibody - Part 1 N2 - Under the auspices of the Protein Analysis Working Group (PAWG) of the Comité Consultatif pour la Quantité de Matière (CCQM) a pilot study, CCQM-P216, was coordinated by the Chinese National Institute of Metrology (NIM), National Research Council of Canada (NRC) and the Bureau International des Poids et Mesures (BIPM). Eleven Metrology Institutes or Designated Institutes and the BIPM participated in the first phase of the pilot study (Part 1). The purpose of this pilot study was to develop measurement capabilities for larger proteins using a recombinant humanized IgG monoclonal antibody against Spike glycoprotein of SARS-CoV-2 (Anti-S IgG mAb) in solution. The first phase of the study was designed to employ established methods that had been previously studies by the CCQM Protein Analysis Working Group, involving the digestion of protein down to the peptide or amino acid level. The global coronavirus pandemic has also led to increased focus on antibody quantitation methods. IgG are among the immunoglobulins produced by the immune system to provide protection against SARS-CoV-2. Anti-SARS-CoV-2 IgG can therefore be detected in samples from affected patients. Antibody tests can show whether a person has been exposed to the SARS-CoV-2, and whether or not they potentially show lasting immunity to the disease. With the constant spread of the virus and the high pressure of re-opening economies, antibody testing plays a critical role in the fight against COVID-19 by helping healthcare professionals to identify individuals who have developed an immune response, either via vaccination or exposure to the virus. Many countries have launched large-scale antibody testing for COVID-19. The development of measurement standards for the antibody detection of SARS-CoV-2 is critically important to deal with the challenges of the COVID-19 pandemic. In this study, the SARS-CoV-2 monoclonal antibody is being used as a model system to build capacity in methods that can be used in antibody quantification. Amino acid reference values with corresponding expanded uncertainty of 36.10 ± 1.55 mg/kg, 38.75 ± 1.45 mg/kg, 18.46 ± 0.78 mg/kg, 16.20 ± 0.67 mg/kg and 30.61 ± 1.30 mg/kg have been established for leucine, valine, phenylalanine, isoleucine and proline, respectively. Agreement between nearly all laboratories was achieved for the amino acid analysis within 2 to 2.5 %, with one participant achieving markedly higher results due to a technical issue found in their procedure; this result was thus excluded from the reference value calculations. The relatively good agreement within a laboratory between different amino acids was not dissimilar to previous results for peptides or small proteins, indicating that factors such as hydrolysis conditions and calibration procedures could be the largest sources of variability. Peptide reference values with corresponding expanded uncertainty of 4.99 ± 0.28 mg/kg and 6.83 ± 0.65 mg/kg have been established for ALPAPIEK and GPSVFPLAPSSK, respectively. Not surprisingly due to prior knowledge from previous studies on peptide quantitation, agreement between laboratories for the peptide-based analysis was slightly poorer at 3 to 5 %, with one laboratory's result excluded for the peptide GPSVFPLAPSSK. Again, this level of agreement was not significantly poorer than that achieved in previous studies with smaller or less complex proteins. To reach the main text of this paper, click on Final Report. KW - Antibody quantification KW - Amino acid analysis KW - Peptide analysis KW - Round robin test PY - 2021 DO - https://doi.org/10.1088/0026-1394/59/1a/08001 VL - 59 IS - 1A SP - 08001 AN - OPUS4-54972 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Devi, Sarita A1 - Goel, S. A1 - Rani, S. A1 - Schneider, Rudolf J. A1 - Rohilla, R. A1 - Kumari, Surbhi A1 - Prabhakar, N. T1 - MOF-metal nanohybrid-assisted charge transfer amplification for electrochemical biosensing of the MUC1 cancer biomarker N2 - Cancer is a severe disease characterized by high mortality and complex pathophysiology; however, its early and accurate diagnosis remains inadequate. Conventional diagnostic approaches often fall short, particularly for dense tissues, and are frequently invasive, costly, and of limited availability. This reinforces the need for a compact, economical, and ultrasensitive assay that is operationally simple and interpretable. We present an efficient electrochemical detection platform for the cancer biomarker mucin 1 (MUC1). A fluorine-doped tin oxide (FTO) surface was modified with an iron-based metal–organic framework (FeMOF) intercalated with palladium nanorods (PdNR). FeMOF was prepared using Fe3+/Fe2+ precursors at a 1.2/1 mmol ratio and dual ligands, i.e. tetrahydroxy-1,4-benzoquinone and 2-aminobenzene-1,4-dicarboxylic acid. AntiMUC1 antibodies were immobilized on a modified electrode via p-phenylenediamine (PDA) (FTO/FeMOF@PdNR/PDA/antiMUC1Ab) and evaluated using electrochemical impedance spectroscopy (EIS) and voltammetry. The designed sensor demonstrated an excellent binding affinity for the MUC1 antigen. Among these techniques, the EIS method stands out for its technical performance, as evidenced by the high sensitivity (detection limit 0.074 fg mL−1), quantification limit 0.24 fg mL−1, and high analytical sensitivity (1.39 × 103 Ω fg−1 mL−1 cm−2). The negligible cross-reactivity with interferent biomolecules, rapid response (10-minute equilibrium), regenerability up to 5 cycles, high reproducibility (RSD ∼1–3%), and long-term stability (up to 35 days) further validate the suitability of the proposed MUC1 immunosensor. This study presents an ultrasensitive biosensor that is compact, cost-effective, and easy for individuals at home to use after further development into a kit-based end product. Moreover, its excellent functionality for spiked serum samples shows promise for next-generation clinical diagnostics. KW - Antibodies KW - Metal-organic framework KW - Immunoassay PY - 2026 DO - https://doi.org/10.1039/D6AN00018E SP - 1 EP - 11 PB - Royal Society of Chemistry CY - London AN - OPUS4-65726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pereira, P.M.R. A1 - Carvalho, José Joao A1 - Silva, S. A1 - Cavaleiro, J.A.S. A1 - Schneider, Rudolf A1 - Fernandes, R. A1 - Tomé, J.P.C. T1 - Porphyrin conjugated with serum albumins and monoclonal antibodies boosts efficiency in targeted destruction of human bladder cancer cells N2 - The synthesis of a novel PS conjugated with bovine and human serum albumin (BSA and HSA) and a monoclonal antibody anti-CD104 is reported, as well as their biological potential against the human bladder cancer cell line UM-UC-3. No photodynamic effect was detected when the non-conjugated porphyrin was used. Yet, when it was coupled covalently with the mAb anti-CD104, BSA and HSA, the resulting photosensitizer conjugates demonstrated high efficacy in destroying the cancer cells, the mAb anti-CD104 efficacy overruling the albumins. KW - Rinderserumalbumin KW - BSA KW - Monoklonale Antikörper KW - Blasenkrebs KW - Konjugate KW - Conjugates KW - Therapeutische Antikörper KW - CD104 PY - 2014 DO - https://doi.org/10.1039/c3ob42082e SN - 1477-0520 SN - 1477-0539 VL - 12 IS - 11 SP - 1804 EP - 1811 PB - RSC CY - Cambridge AN - OPUS4-30451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kepsutlu, B. A1 - Wycisk, V. A1 - Achazi, K. A1 - Kapishnikov, S. A1 - Perez-Berna, A.J. A1 - Guttmann, P. A1 - Cossmer, Antje A1 - Pereiro, E. A1 - Ewers, H. A1 - Ballauff, M. A1 - Schneider, G. A1 - McNally, J.G. T1 - Cells Undergo Major Changes in the Quantity of Cytoplasmic Organelles after Uptake of Gold Nanoparticles with Biologically Relevant Surface Coatings N2 - Here, we use cryo soft X-ray tomography (cryo-SXT), which delivers 3D ultrastructural volumes of intact cells without chemical fixation or staining, to gain insight about nanoparticle uptake for nanomedicine. We initially used dendritic polyglycerol sulfate (dPGS) with potential diagnostic and therapeutic applications in inflammation. Although dPGS-coated gold nanoparticle (dPGS-AuNP) uptake followed a conventional endocytic/degradative pathway in human lung epithelial cell lines (A549), with cryo-SXT, we detected ∼5% of dPGS-AuNPs in the cytoplasm, a level undetectable by confocal light microscopy. We also observed ∼5% of dPGS-AuNPs in a rarely identified subcellular site, namely, lipid droplets, which are important for cellular energy metabolism. Finally, we also found substantial changes in the quantity of cytoplasmic organelles upon dPGS-AuNP uptake over the 1–6 h incubation period; the number of small vesicles and mitochondria significantly increased, and the number of multivesicular bodies and the number and volume of lipid droplets significantly decreased. Although nearly all organelle numbers at 6 h were still significantly different from controls, most appeared to be returning to normal levels. To test for generality, we also examined cells after uptake of gold nanoparticles coated with a different agent, polyethylenimine (PEI), used for nucleic acid delivery. PEI nanoparticles did not enter lipid droplets, but they induced similar, albeit less pronounced, changes in the quantity of cytoplasmic organelles. We confirmed these changes in organelle quantities for both nanoparticle coatings by confocal fluorescence microscopy. We suggest this cytoplasmic remodeling could reflect a more common cellular response to coated gold nanoparticle uptake. KW - Cellular trafficking KW - Confocal laser scanning microscopy KW - Cytoplasmic remodeling KW - Dendritic polyglycerol sulfate KW - Polyethylenimine KW - 3D ultrastructural analysis KW - Cryo-soft X-ray tomography PY - 2020 DO - https://doi.org/10.1021/acsnano.9b09264 VL - 14 IS - 2 SP - 2248 EP - 2264 AN - OPUS4-50464 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulze-Makuch, D. A1 - Haque, S. A1 - Beckles, D. A1 - Schmitt-Kopplin, P. A1 - Harir, M. A1 - Schneider, Beate A1 - Stumpp, C. A1 - Wagner, D. T1 - A chemical and microbial characterization of selected mud volcanoes in Trinidad reveals pathogens introduced by surface water and rain water N2 - Terrestrial mud volcanoes are unique structures driven by tectonic pressure and fluids from the deep subsurface. These structures are mainly found in active tectonic zones, such as the area near the Los Bajos Fault in Trinidad. Here we report a chemical and microbiological characterization of three mud volcanoes, which included analyses of multiple liquid and solid samples from the mud volcanoes. Our study confirms previous suggestions that at least some of the mud volcano fluids are a mixture of deeper salt-rich water and surficial/precipitation water. No apparent water quality differences were found between sampling sites north and south of a major geological fault line. Microbiological analyses revealed diverse communities, both aerobic and anaerobic, including sulfate reducers, methanogens, carbon dioxide fixing and denitrifying bacteria. Several identified species were halophilic and likely derived from the deeper salt-rich subsurface water, while we also cultivated pathogenic species from the Vibrionaceae, Enterobacteriaceae, Shewanellaceae, and Clostridiaceae. These microorganisms were likely introduced into the mud volcano fluids both from surface water or shallow ground-water, and perhaps to a more minor degree by rain water. The identified pathogens are a major health concern that needs to be addressed. KW - Water stable isotope analysis KW - Mud volcanoe fluids KW - Metabolomics PY - 2020 DO - https://doi.org/10.1016/j.scitotenv.2019.136087 VL - 707 SP - 136087 PB - Elsevier B.V. AN - OPUS4-50499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, S. A1 - Schneider, Ronald A1 - Faber, M.H. ED - Haukaas, T. T1 - Quantification of the value of structural health monitoring information for fatigue deteriorating structural systems N2 - This paper addresses the quantification of the value of structural health monitoring (SHM) before its implementation for structural systems on the basis of its Value of Information (VoI). The value of SHM is calculated utilizing the Bayesian pre-posterior decision analysis modelling the structural life cycle performance, the integrity management and the structural risks. The relevance and precision of SHM information for the reduction of the structural system risks and the expected cost of the structural integrity management throughout the life cycle constitutes the value of SHM and is quantified with this framework. The approach is focused on fatigue deteriorating structural steel systems for which a continuous resistance deterioration formulation is introduced. In a case study, the value of SHM for load monitoring is calculated for a Daniels system subjected to fatigue deterioration. The influence of and the value of SHM in regard to the structural system risks and the integrity management is explicated and explained. The results are pointing to the importance of the consideration of the structural system risks for the quantification of the value of SHM. T2 - ICASP 12 - 12th International conference on applications of statistics and probability in civil engineering CY - Vancouver, Canada DA - 12.07.2015 PY - 2015 DO - https://doi.org/10.14288/1.0076284 SP - Paper 605, 1 EP - 8 AN - OPUS4-34332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Ronald A1 - Fischer, J. A1 - Bügler, M. A1 - Nowak, M. A1 - Thöns, S. A1 - Borrmann, A. A1 - Straub, D. T1 - Assessing and updating the reliability of concrete bridges subjected to spatial deterioration - principles and software implementation N2 - Inspection and maintenance of concrete bridges is a major cost factor in transportation infrastructure, and there is significant potential for using information gained during inspection to update predictive models of the performance and reliability of such structures. In this context, this paper presents an approach for assessing and updating the reliability of prestressed concrete bridges subjected to chloride-induced reinforcement corrosion. The system deterioration state is determined based on a Dynamic Bayesian Network (DBN) model that considers the spatial variability of the corrosion process. The overall system reliability is computed by means of a probabilistic structural model coupled with the deterioration model. Inspection data are included in the system reliability calculation through Bayesian updating on the basis of the DBN model. As proof of concept, a software prototype is developed to implement the method presented here. The software prototype is applied to a typical highway bridge and the influence of inspection information on the system deterioration state and the structural reliability is quantified taking into account the spatial correlation of the corrosion process. This work is a step towards developing a software tool that can be used by engineering practitioners to perform reliability assessments of ageing concrete bridges and update their reliability with inspection and monitoring data. KW - Structural reliability KW - Dynamic Bayesian Networks KW - Spatial deterioration KW - Inspection KW - Monitoring general KW - Analysis and design methods KW - Reinforcement KW - Corrosion KW - Prestressed concrete PY - 2015 DO - https://doi.org/10.1002/suco.201500014 SN - 1464-4177 VL - 16 IS - 3 SP - 356 EP - 365 PB - Ernst & Sohn CY - Berlin AN - OPUS4-34336 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Schneider, S. A1 - Prediger, L. A1 - Flassenberg, G. ED - Hájek, P. ED - Tywoniak, J. ED - Lupísek, A. ED - Sojková, K. T1 - Sustainability analysis for the recycling of masonry T2 - CESB 13 - 3rd International conference Central Europe towards sustainable building - Sustainable building and refurbishment for next generations CY - Prague, Czech Republic DA - 2013-06-26 KW - Masonry KW - Recycling KW - Sustainability KW - LCA KW - LCC KW - LCWE PY - 2013 SN - 978-80-247-5015-6 SN - 978-80-247-5017-0 SP - 345 EP - 348 AN - OPUS4-30407 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Schneider, S. A1 - Brandstetter, C.P. A1 - Flassenberg, G. T1 - Stoffkreislauf im Mauerwerksbau - Nachhaltigkeitsanalyse für das Mauerwerksrecycling N2 - In Deutschland fallen nach Abschätzungen von jährlich bis zu 10 Millionen Tonnen Mauerwerkbruch an. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind diese Restmassen zukünftig einem möglichst hochwertigen und individuell angepassten Recycling zuzuführen. Vor diesem Hintergrund wurde im IGF-Forschungsvorhaben 17022 N der Forschungsvereinigung Porenbetonindustrie e.V. die Nachhaltigkeit verschiedener Recyclingoptionen für Mauerwerkbruch ganzheitlich untersucht. Unter Einbeziehung der Hauptmauersteinarten Ziegel, Kalksandstein, Porenbeton und Leichtbeton wurden dabei material- und verfahrenstechnische sowie ökologische, ökonomische und soziale Aspekte berücksichtigt. Als Ergebnis wurde ein EDV-gestütztes Analysetool (Web-Tool) zur Nachhaltigkeitsbewertung für das Mauerwerksrecycling entwickelt. Mit dem Web-Tool sollen Anwender (Planer, Architekten, Recycler) die Möglichkeit erhalten, für verschiedene Untersuchungsfälle unter Einbeziehung regional und sachlich bedingter Parameter objektspezifische Aussagen zur Nachhaltigkeit treffen zu können. Auf diesem Wege können im Sinne der aktuellen gesetzlichen Vorgaben nachhaltige Stoffkreisläufe im Mauerwerksbau geschlossen und somit letztlich die Deponierung von Mauerwerksrestmassen reduziert oder gar vermieden werden. T2 - R'13 - Fachtagung Recycling CY - Weimar, Germany DA - 19.09.2013 PY - 2013 SP - 1 EP - 6 PB - Bauhaus-Univ. CY - Weimar AN - OPUS4-30408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Stephan A1 - Hanelt, S. A1 - Canitz, C. A1 - Hoffmann, Holger A1 - Garbe, L.-A. A1 - Schneider, Rudolf T1 - Entwicklung monoklonaler Antikörper gegen Diclofenac N2 - Diclofenac (DCF) wird als nicht-steroidales, antientzündliches Arzneimittel gegen Fieber, Entzündungen, rheumatische Erkrankungen und Schmerzen eingesetzt. 70 % werden nach Einnahme wieder ausgeschieden. Aufgrund unvollständiger Elimination in den Kläranlagen lassen sich Rückstände im Trinkwasser und im Oberflächengewässer nachweisen. Diclofenac wird in der Umweltanalytik v.a. mittels GC-MS oder LCMS nachgewiesen. Bioanalytische Methoden machen sich die spezifische Antigen-Antikörper-Wechselwirkung zunutze, so z.B. Immunoassays. Die hierfür erforderlichen Antikörper werden durch Immunisierung mit einem Konjugat aus dem Analyten und einem Trägerprotein gewonnen. Die Kopplung kann direkt über die Carboxylfunktion von Diclofenac erfolgen. Um Abschirmungseffekte zu vermeiden, kann zwischen Protein und Analy1 ein Spacer sinnvoll sein. PY - 2015 SN - 1618-3258 SN - 1617-5301 IS - 4 SP - 107 EP - 109 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-35241 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schneider, Ronald A1 - Fischer, J. A1 - Straub, D. A1 - Thöns, S. A1 - Bügler, M. A1 - Borrmann, A. T1 - Intelligente Bauwerke - Prototyp zur Ermittlung der Schadens- und Zustandsentwicklung für Elemente des Brückenmodells N2 - Dieser Bericht beschreibt ein Systemmodell für eine integrale Ermittlung und Prognose der Schadens- und Zustandsentwicklung der Elemente eines Brückensystems unter Berücksichtigung von Ergebnissen aus Inspektionen und Überwachung. Das Systemmodell wurde anhand eines ausgesuchten Spannbetonüberbaus in einzelliger Kastenbauweise entwickelt. Es besteht aus zwei integralen Teilmodellen: ein Modell zur Beschreibung des Systemschädigungszustandes und ein Modell zur Beschreibung der Standsicherheit. Für die Modellierung des stochastischen Systemschädigungszustandes eines Brückensystems werden dynamische Bayes'sche Netze (DBN) vorgeschlagen. Dieser Ansatz ermöglicht es, alle relevanten Schädigungsprozesse und deren stochastische Abhängigkeiten zu berücksichtigen. Ein wesentlicher Vorteil dieses Ansatzes ist es, dass DBN ideal dafür geeignet sind, Bayes'sche Aktualisierungen auf Grundlage von Informationen aus Inspektionen und Überwachungsmaßnahme auf eine effiziente und robuste Art und Weise durchzuführen. Der DBN-Ansatz ist deshalb für die Entwicklung von Software für das Erhaltungsmanagement von alternden Brückenbauwerken, die vom Benutzer keine vertieften Kenntnisse der Zuverlässigkeitstheorie verlangt, ideal geeignet. Für die Modellierung der Standsicherheit eines alternden Kastenträgers wird vereinfachend Biegeversagen des globalen Längssystems betrachtet. Zur Berechnung der maximalen Traglast eines Kastenträgers infolge des Systemschädigungszustandes wird ein plastisch-plastisches Verfahren eingesetzt, wobei die Beanspruchungen mittels der Fließgelenktheorie unter Ausnutzung der plastischen Beanspruchbarkeit der Querschnitte des Kastenträgers ermittelt werden. Ein Kastenträger versagt, wenn sich durch die Ausbildung einer ausreichend großen Anzahl von Fließgelenken eine kinematische Kette ausbildet. Dieser Modellierungsansatz berücksichtigt Redundanzen, die sich aus der plastischen Beanspruchbarkeit der Querschnitte und der statischen Unbestimmtheit eines Kastenträgers ergeben. Zum Nachweis der praktischen Einsetzbarkeit des entwickelten Systemmodells wurde ein Software-Prototyp entwickelt, der eine intuitiv benutzbare graphische Benutzeroberfläche (Front-End) mit einem Berechnungskern (Back-End) koppelt. Die aktuelle Version des Software-Prototyps implementiert ein Modell der chloridinduzierten Bewehrungskorrosion und ein Tragwerksmodell, welches das Verfahrens der stetigen Laststeigerung zur Bestimmung der maximalen Traglast des Kastenträgers auf der Grundlage eines Finite-Elemente-Modells umsetzt. Zur Durchführung von Bayes'schen Aktualisierungen des Systemschädigungszustandes auf der Grundlage des DBN-Modells implementiert der Prototyp den Likelihood-Weighting-Algorithmus. Die entwickelte Architektur des Prototyps ermöglicht eine Erweiterung der Software um weitere Schädigungsprozesse. Der entwickelte Software-Prototyp ermöglicht Benutzern ohne vertiefte Kenntnisse der Zuverlässigkeitstheorie eine Berechnung des Einflusses von Bauwerksinformationen auf den Systemschädigungszustand und die Tragsicherheit eines Kastenträgers. Auf dieser Grundlage können effiziente Inspektions- und Überwachungsmaßnahmen identifiziert und das Erhaltungsmanagement optimiert werden. KW - Bridge KW - Condition survey KW - Damage KW - Deterioration KW - Development KW - Digital model KW - Durability KW - Engineering structure KW - Expert system KW - Forecast KW - Germany KW - Propability KW - Prototype KW - Reinforced concrete KW - Research report KW - Software KW - Stability KW - Stochastic process PY - 2015 UR - http://bast.opus.hbz-nrw.de/volltexte/2015/1615/ SN - 978-3-95606-190-5 SN - 0943-9293 VL - 117 SP - 1 EP - 74 PB - Carl Schünemann Verlag GmbH CY - Bergisch Gladbach AN - OPUS4-35193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raysyan, Anna A1 - Galvidis, I. A. A1 - Schneider, Rudolf A1 - Eremin, S. A. A1 - Burkin, M. A. T1 - Development of a latex particles-based lateral flow immunoassay for group determination of macrolide antibiotics in breast milk N2 - A lateral flow immunoassay (LFIA) using latex particles labeled with antibody to BSAclarithromycin (CLA) was developed for the rapid simultaneous group determination of six macrolide antibiotics. Optimization of antigen spotting on the membrane and latex probe loading allowed improving visual detectability (vLOD) 100 times, which was 1, 1, 10, 10, 50, and 1000 ng/mL for CLA, roxithromycin, erythromycin, dirithromycin, azithromycin, and oleandomycin in buffer, respectively. The calculated limits of instrumental detection (cLOD) were respectively 0.12, 0.15, 1.4, 2.1, 2.4, and 3.3 ng/mL. To avoid a strong influence of breast milk of a very diverse and variable composition, a sample pretreatment is proposed. The six macrolides mentioned can be visually detected in breast milk after 20 minutes pretreatment at concentrations of 10-1000 ng / ml or instrumentally with cLOD of 4.0, 2.5, 30, 42, 42 and 180 ng/mL. The recovery rate from the spiked samples carried out using a strip scanner device ranged from 71% to 110%, and precision expressed as relative standard deviation was between 3-14%. The described rapid on-site diagnostic assay format can be useful for monitoring the content of antibiotics in breast milk during macrolide treatment to ensure safe breastfeeding of infants. KW - Clarithromycin KW - Roxithromycin KW - Erythromycin KW - Dirithromycin KW - Azithromycin KW - Oleandomycin KW - Macrolide antibiotics KW - Makrolide KW - Antibiotika PY - 2020 DO - https://doi.org/10.1016/j.jpba.2020.113450 SN - 0731-7085 VL - 189 IS - 113450 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam, NL AN - OPUS4-51343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raysyan, Anna A1 - Moerer, R. A1 - Coesfeld, Bianca A1 - Eremin, S. A1 - Schneider, Rudolf T1 - Fluorescence polarization immunoassay for the determination of diclofenac in wastewater N2 - Pharmacologically active compounds are often detected in wastewater and surface waters. The nonsteroidal anti-inflammatory drug diclofenac (DCF) was included in the European watch list of substances that requires its environmental monitoring in the member states. DCF may harmfully influence the ecosystem already at concentrations ≤ 1 μg L−1. The fast and easy quantification of DCF is becoming a subject of global importance. Fluorescence polarization immunoassay (FPIA) is a homogeneous mix-and-read method which does not require the immobilization of reagents. FPIA can be performed in one phase within 20–30 min, making it possible to analyse wastewater without any complicated pre-treatment. In this study, new tracermolecules with different structures, linking fluorophores to derivatives of the analyte, were synthesized, three homologous tracers based on DCF, two including a C6 spacer, and one heterologous tracer derived from 5-hydroxy-DCF. The tracer molecules were thoroughly assessed for performance. Regarding sensitivity of the FPIA, the lowest limit of detection reached was 2.0 μg L−1 with a working range up to 870 μg L−1. The method was validated for real wastewater samples against LC-MS/MS as reference method with good agreement of both methods. KW - Abwasser KW - Umweltschadstoffe KW - Antikörper KW - Antibody PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-518398 DO - https://doi.org/10.1007/s00216-020-03058-w SN - 1618-2642 VL - 413 IS - 4 SP - 999 EP - 107 PB - Springer CY - Heidelberg AN - OPUS4-51839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scala-Benuzzi, M. L. A1 - Soler-Illia, G. J. A. A. A1 - Rabia, J. A1 - Battaglini, F. A1 - Schneider, Rudolf A1 - Pereira, S. V. A1 - Messina, G. A. T1 - Immunosensor based on porous gold and reduced graphene platform for the determination of EE2 by electrochemical impedance spectroscopy N2 - In this work, we report an electrochemical immunosensor to detect ethinylestradiol in water samples, using electrochemical impedance spectroscopy (EIS) as a detection technique. For the development of this immunosensor, the direct modification of the working electrode of a screen-printed carbon electrode was carried out. First, to reduce the resistance of the electrode, electroreduced graphene was incorporated on the surface. Second, a porous gold structure was electrodeposited on reduced graphene by electrodeposition and the dynamic hydrogen bubble template assisted method. Thus, a marked increase in surface area was obtained for anti-EE2 antibodies immobilization. Subsequently, the specific anti-EE2 antibodies were covalently immobilized using α-lipoic acid for attaching them to the gold surface. The electrode modified with the antibodies was incubated for 30 min in the samples containing EE2, producing the specific Antigen antibody binding. As the charge transfer resistance of a redox probe in the electrode surface is governed by the surface blocking effects, the charge transfer resistance was related to the amount of EE2 captured to realize a quantitative determination. For this, the EIS measurements were performed in a 4 mM [Fe(CN)6]4−/3− solution in 0.1 M KCl. The obtained Nyquist diagrams were adjusted using the Randles circuit as an equivalent circuit to obtain the corresponding resistances. The developed methodology showed good selectivity, precision, and sensitivity; although the LOD obtained was higher than those presented in other published articles, it turned out to be an alternative that allows the determination of ethinylestradiol using a simple disposable electrode. KW - Ethinylestradiol KW - Biosensor KW - Elektrochemisch KW - Impedanz PY - 2021 DO - https://doi.org/10.1016/j.jelechem.2021.115604 SN - 1572-6657 VL - 897 SP - 115604 EP - 115611 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-54048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Florian, Camilo A1 - Fischer, Daniel A1 - Freiberg, K. A1 - Duwe, M. A1 - Sahre, Mario A1 - Schneider, S. A1 - Hertwig, Andreas A1 - Krüger, Jörg A1 - Rettenmayr, M. A1 - Beck, Uwe A1 - Undisz, A. A1 - Bonse, Jörn T1 - Single Femtosecond Laser-Pulse-Induced Superficial Amorphization and Re-Crystallization of Silicon N2 - Superficial amorphization and re-crystallization of silicon in <111> and <100> orientation after irradiation by femtosecond laser pulses (790 nm, 30 fs) are studied using optical imaging and transmission electron microscopy. Spectroscopic imaging ellipsometry (SIE) allows fast data acquisition at multiple wavelengths and provides experimental data for calculating nanometric amorphous layer thickness profiles with micrometric lateral resolution based on a thin-film layer model. For a radially Gaussian laser beam and at moderate peak fluences above the melting and below the ablation thresholds, laterally parabolic amorphous layer profiles with maximum thicknesses of several tens of nanometers were quantitatively attained. The accuracy of the calculations is verified experimentally by high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (STEM-EDX). Along with topographic information obtained by atomic force microscopy (AFM), a comprehensive picture of the superficial re-solidification of silicon after local melting by femtosecond laser pulses is drawn. KW - Femtosecond laser KW - Silicon KW - Amorphization KW - Crystallization KW - Spectroscopic imaging ellipsometry PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-523687 UR - https://www.mdpi.com/1996-1944/14/7/1651 DO - https://doi.org/10.3390/ma14071651 SN - 1996-1944 VL - 14 IS - 7 SP - 1651-1 EP - 1651-21 PB - MDPI AG CY - Basel, Switzerland AN - OPUS4-52368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -