TY - JOUR A1 - Zhou, X. A1 - Mathews, P. A1 - Berkels, B. A1 - Delis, W. A1 - Saood, S. A1 - Alhassan, A. A1 - Keuter, P. A1 - Schneider, J. A1 - Korte-Kerzel, S. A1 - Sandlöbes, S. A1 - Raabe, D. A1 - Neugebauer, j. A1 - Dehm, G. A1 - Hickel, Tilmann A1 - Scheu, C. A1 - Zhang, S. T1 - Materials Design by Constructing Phase Diagrams for Defects N2 - Phase transformations and crystallographic defects are two essential tools todrive innovations in materials. Bulk materials design via tuning chemicalcompositions is systematized using phase diagrams. It is shown here that thesame thermodynamic concept can be applied to manipulate the chemistry atdefects. Grain boundaries in Mg–Ga system are chosen as a model system,because Ga segregates to the boundaries, while simultaneously improving thestrength and ductility of Mg alloys. To reveal the role of grain boundaries,correlated atomic-scale characterization and simulation to scope and buildphase diagrams for defects are presented. The discovery is enabled bytriggering phase transformations of individual grain boundaries through localalloying, and sequentially imaging the structural and chemical changes usingatomic-resolution scanning transmission electron microscopy. Ab initiosimulations determined the thermodynamic stability of grain boundaryphases, and found out that increasing Ga content enhances grain boundarycohesion, relating to improved ductility. The methodology to trigger, trace,and simulate defect transformation at atomic resolution enables a systematicdevelopment of defect phase diagrams, providing a valuable tool to utilizechemical complexity and phase transformations at defects. KW - Automatic pattern recognition KW - Defect phase diagram KW - Density functional theory KW - Grain boundary complexion KW - Transmission electron microscopy PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618063 DO - https://doi.org/10.1002/adma.202402191 SN - 1521-4095 SP - 1 EP - 9 PB - Wiley AN - OPUS4-61806 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Thomas A1 - Vierneusel, B. A1 - Gradt, Thomas A1 - Tremmel, S. A1 - Wartzack, S. A1 - Szücs, Z. A1 - Arendt, I. T1 - Optimierte MoS2-PVD-Schichten für wechselnde Umgebungsbedingungen N2 - Der Festschmierstoff Molybdändisulfid ist insbesondere für Extremanwendungen ein gerne eingesetzter Werkstoff, problematisch ist jedoch der negative Einfluss von Feuchtigkeit. Bei mittels PVD-Verfahren abgeschiedenen MoS2-Schichten ergibt sich jedoch die Möglichkeit, durch Anpassung der Beschichtungsparameter vorwiegend basal ausgerichtete Schichten herzustellen, die auch an Luft ein verbessertes tribologisches Verhalten zeigen. N2 - The solid lubricant molybdenum disulfide is a well known material for extreme conditions, but Problems arise due to a negative effect of humidity. However, by using a PVD process, deposition parameters can be optimized to gain coatings with a more textured structure orienting the basal planes parallel to the Substrate surface. Therefore, an improved tribological behavior even under moist conditions can be achievcd. KW - MoS2-coatings KW - PVD-process KW - Tribology KW - Moisture KW - Cryogenic temperatures KW - MoS2-Beschichtungen KW - PVD KW - Tribologie KW - Luftfeuchte KW - Kryogene Temperaturen PY - 2013 SN - 0724-3472 VL - 60 IS - 4 SP - 18 EP - 23 PB - Expert Verlag CY - Renningen AN - OPUS4-29995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulze-Makuch, D. A1 - Lipus, D. A1 - Arens, F. L. A1 - Baque, M. A1 - Bornemann, T. L. V. A1 - de Vera, J. P. A1 - Flury, M. A1 - Froesler, J. A1 - Heinz, J. A1 - Hwang, Y. A1 - Kounaves, S. P. A1 - Mangelsdorf, K. A1 - Meckenstock, R. U. A1 - Pannekens, M. A1 - Probst, A. J. A1 - Saenz, J. S. A1 - Schirmack, J. A1 - Schloter, M. A1 - Schmitt-Kopplin, P. A1 - Schneider, Beate A1 - Uhl, J. A1 - Vestergaard, G. A1 - Valenzuela, B. A1 - Zamorano, P. A1 - Wagner, D. T1 - Microbial hotspots in lithic microhabitats inferred from DNA fractionation and metagenomics in the Atacama Desert N2 - The existence of microbial activity hotspots in temperate regions of Earth is driven by soil heterogeneities, especially the temporal and spatial availability of nutrients. Here we investigate whether microbial activity hotspots also exist in lithic microhabitats in one of the most arid regions of the world, the Atacama Desert in Chile. While previous studies evaluated the total DNA fraction to elucidate the microbial communities, we here for the first time use a DNA separation approach on lithic microhabitats, together with metagenomics and other analysis methods (i.e., ATP, PLFA, and metabolite analysis) to specifically gain insights on the living and potentially active microbial community. Our results show that hypolith colonized rocks are microbial hotspots in the desert environment. In contrast, our data do not support such a conclusion for gypsum crust and salt rock environments, because only limited microbial activity could be observed. The hypolith community is dominated by phototrophs, mostly Cyanobacteria and Chloroflexi, at both study sites. The gypsum crusts are dominated by methylotrophs and heterotrophic phototrophs, mostly Chloroflexi, and the salt rocks (halite nodules) by phototrophic and halotolerant endoliths, mostly Cyanobacteria and Archaea. The major environmental constraints in the organic-poor arid and hyperarid Atacama Desert are water availability and UV irradiation, allowing phototrophs and other extremophiles to play a key role in desert ecology. KW - Desert ecology KW - Extremophile KW - Hyperarid PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527959 DO - https://doi.org/10.3390/microorganisms9051038 SN - 2076-2607 VL - 9 IS - 5 SP - 1038 PB - MDPI CY - Basel AN - OPUS4-52795 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Beck, Uwe A1 - Ermilova, Elena A1 - Schneider, S. A1 - Peters, S. T1 - Gemeinsamer Abschlussbericht WIPANO-Vorhaben „Standardisierung und Normung der Ellipsometrie als universeller Spektroskopie“ N2 - Im Vorhaben SNELLIUS wurden in enger Zusammenarbeit der BAM mit den Firmen Accurion und SENTECH Instruments aufbauend auf der Norm DIN 50989-1 „Ellipsometrie - Teil 1: Grundlagen; Ellipsometry – Part 1: Principles“ insgesamt fünf Normenentwürfe erarbeitet, die fünf Modell-basierten Anwendungsfällen der Ellipsometrie entsprechen. Unter Berücksichtigung des neuartigen Modell-basierten Normungskonzepts wurde in den Normenentwürfen erstmals eine GUM- und DIN EN ISO/IEC 17025:2018 konforme Bestimmung bzw. Abschätzung der Messunsicherheit umgesetzt. Dies erforderte neben der textlichen Erstellung auch umfangreiche experimentelle Arbeiten bei den Firmen, Vergleichsversuche und komplementäre Modell- und Datenevaluierungen, da sowohl die verwendete ellipsometrische Hardware (unterschiedliche ellipsometrische Funktionsprinzipien) als auch die ellipsometrische Software (Modell-Randbedingungen, Fitalgorithmus) firmenspezifisch zum Teil sehr unterschiedlich sind. Hierbei mussten in einem Konsensprozess Lösungen gefunden werden, die die beiden deutschen Ellipsometer-Anbieter Accurion (Imaging-Ellipsometrie) und SENTECH Instruments (Mapping Ellipsometrie) gleichermaßen akzeptieren konnten und die zudem einen Transfer auf die Internationale Ebene (ISO Norm) ermöglichen, also vom Grundsatz her auch auf weitere Ellipsometerhersteller wie (J. A. Woollam Co., USA; SEMILAB, Ungarn; HORIBA, Japan) mit wieder anderen ellipsometrischen Funktionsprinzipien, Hard- und Softwarelösungen anwendbar sind. Die weitgehende Unabhängigkeit von ellipsometrischen Funktionsprinzipien, Hard- und Softwarelösungen wurde dadurch erreicht, dass normativ festgelegt wurde, dass die ellipsometrischen Größen PSI und DELTA im Sinne von DIN ENISO/IEC 17025 als Rohdaten fungieren. KW - Ellipsometrie-Norm KW - Messunsicherheit ellipsometrischer Messungen KW - Validierungskonzepte ellipsometrischer Messungen KW - DIN 50989, Teile 1 bis 6 KW - DIN EN ISO/IEC 17025:2018 und GUM Kompatibilität PY - 2021 SP - 1 EP - 16 AN - OPUS4-52857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raysyan, Anna A1 - Zwigart, S. A1 - Eremin, S. A. A1 - Schneider, Rudolf T1 - BPA Endocrine Disruptor Detection at the Cutting Edge: FPIA and ELISA Immunoassays N2 - BPA is a chemical commonly used in the production of polymer-based materials that can have detrimental effects on the thyroid gland and impact human reproductive health. Various expensive methods, such as liquid and gas chromatography, have been suggested for detecting BPA. The fluorescence polarization immunoassay (FPIA) is an inexpensive and efficient homogeneous mix-and-read method that allows for high-throughput screening. FPIA offers high specificity and sensitivity and can be carried out in a single phase within a timeframe of 20–30 min. In this study, new tracer molecules were designed that linked the fluorescein fluorophore with and without a spacer to the bisphenol A moiety. To assess the influence of the C6 spacer on the sensitivity of an assay based on the respective antibody, hapten–protein conjugates were synthesized and assessed for performance in an ELISA setup, and this resulted in a highly sensitive assay with a detection limit of 0.05 µg/L. The lowest limit of detection was reached by employing the spacer derivate in the FPIA and was 1.0 µg/L, working range from 2 to 155 µg/L. The validation of the methods was conducted using actual samples compared to LC–MS/MS, which served as the reference method. The FPIA and ELISA both demonstrated satisfactory concordance. KW - Fluorescence Polarization KW - Enzyme-Linked Immunosorbent Assay KW - Endokriner Disruptor KW - Bisphenol A KW - Freisetzung PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579497 DO - https://doi.org/10.3390/bios13060664 VL - 13 IS - 6 SP - 1 EP - 12 PB - MDPI CY - Basel AN - OPUS4-57949 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Rudolf A1 - Schmidt, S. A1 - Hanelt, S. A1 - Canitz, C. A1 - Hoffmann, H. A1 - Garbe, L.-A. T1 - Synthetic Strategies for the Modification of Diclofenac N2 - For many heterogeneous sensor applications as well as the synthesis of hapten antigens to produce antibodies, protein conjugates of the target substance are essential. A requirement is that the target substance already offers or is modified to contain a functionality that allows for coupling to a protein, that is, an amino acid residue. Ideally, to avoid shielding of the compound by the carrier protein, a sufficient distance to the protein surface should be provided. With its carboxyl function diclofenac (DCF) allows for direct binding to lysine residues after in situ synthesis of the NHS ester. One problem is that diclofenac as free acid tends to autocondensation, which results in low yields. Here we describe the 'insertion' of a C6 spacer via synthesis of the amide with 6-aminohexanoic acid. To carry out the reaction in solution, first the methyl ester of the amino acid had to be produced. Due to otherwise low yields and large cleaning efforts, solid-phase synthesis on Fmoc Ahx Wang resin is recommended. The crude product is mainly contaminated by cleavage products from the resin which were removed by chromatography. The structure of the highly pure hapten was completely determined by nuclear magnetic resonance (NMR) spectroscopy. KW - Diclophenac KW - Hapten synthesis KW - Solid-phase synthesis PY - 2017 DO - https://doi.org/10.1055/s-0036-1588858 SN - 0936-5214 VL - 28 IS - 15 SP - 1984 EP - 1989 PB - Georg Thieme Verlag AN - OPUS4-43316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Recknagel, Christoph A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Commer, T. A1 - Gallai, G. A1 - Goldschmidt, M. A1 - Habiger, D. A1 - Karczewski, B. A1 - Koll, R.-J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Rossi, M. A1 - Schneider, T. A1 - Seiffart, J. A1 - Staeck, M. A1 - Stark, S. A1 - Wehner, H. A1 - Willand, E. T1 - Hinweise für die Herstellung von Fahrbahnübergängen aus Poyurea oder Polyurethan für Ingenieurbauten - H FüPP N2 - Diese Hinweisbroschüre erläutert allgemeine Planungsvoraussetzungen und Dimensionierungsregelungen, Baugrundsätze und Zulassungsbedingungen zur Anwendung innovativer Belagsdehnfugensysteme (Fahrbahnübergangskonstruktionen) in hochbeanspruchten Verkehrsflächen des Bundesfernstraßenbereiches. Alle planungsrelevanten, baustoffrelevanten, versuchstechnische, qualitätssichernden und baupraktischen Aspekte werden zur Unterstützung der Straßenbauverwaltungen, der Lieferfirmen und Ausführungsbetriebe erläutert. Die Veröffentlichung stellt eine technische Analyse aus Erfahrungssammlungen und Auswertung praktischer Erkenntnisse dar. KW - Brückenbeläge KW - Fahrbahnübergänge KW - Dehnfugenkonstruktionen KW - technische und technologische Anforderungen PY - 2022 SN - 978-3-86446-355-6 VL - 778 SP - 1 EP - 47 PB - Forschungsgesellschaft für Straßen- und Verkehrswesen CY - Köln AN - OPUS4-59374 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Thomas A1 - Gradt, Thomas A1 - Vierneusel, B. A1 - Tremmel, S. A1 - Wartzack, S. T1 - Tribological behavior of MoS2 in hydrogen environment N2 - The solid lubricant molybdenum disulfide is a well known material for extreme conditions where conventional oil or grease lubrication is not feasible (vacuum, high pressures). However, under reactive environments e.g. high humidity or hydrogen MoS2 is prone to premature failure. By using a PVD process, deposition parameters can be optimized to gain coatings with a more textured structure orienting the basal planes parallel to the Substrate surface, A similar concept has been used by Koch et al. for coatings developed to withstand the extreme operational conditions of the WENDELSTEIN W7-X fusion experiment. Therefore, an improved tribological behavior even under adverse conditions can be achieved. T2 - WTC 2013 - 5th World tribology congress CY - Torino, Italy DA - 08.09.2013 KW - Tribologie KW - Festschmierstoffe KW - MoS2 KW - Wasserstofftechnologie PY - 2013 SP - 1 EP - 3 AN - OPUS4-31156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vierneusel, B. A1 - Schneider, Thomas A1 - Tremmel, S. A1 - Wartzack, S. A1 - Gradt, Thomas T1 - Humidity resistant MoS2 coatings deposited by unbalanced magnetron sputtering N2 - MoS2 is a suitable solid lubricant for environments free of oxygen or water vapor (i.e. vacuum). Humid air degrades film properties due to oxidation accompanied by high wear and increasing coefficients of friction. The present study aims at the further development of sputtered pure MoS2 coatings, extending their applicability to varying environmental conditions by increasing the resistance against humidity. The systematic coating development process is supported by using an experimental Box–Behnken design with variations of the deposition parameters cathode voltage, target/substrate distance, temperature and argon gas pressure. In contrast to common one-factor-at-a-time (OFAT) studies, this approach enables a determination of interactions between deposition process parameters and tribological–mechanical MoS2 film properties. The tribological improvement focuses on a maximization of wear resistance in air and vacuum measured in ball-on-disk experiments. The evaluated mechanical properties are hardness, elastic modulus and residual stresses. These stresses were determined by the substrate curvature method. The study reveals that the residual stress state in the films and the hardness-to-modulus ratio are crucial for their tribological performance in humid air and vacuum environments. After a detailed determination of the relationships between deposition conditions and film properties, some selected microstructural analyses are presented which show that a substantially basal orientation of the lattice has positive effects on wear but also causes anisotropic film properties which result in fissile fracture of the coating if strong shock or point loads occur. KW - Unbalanced magnetron sputtering KW - MoS2 KW - Humidity resistance KW - Residual stress PY - 2013 DO - https://doi.org/10.1016/j.surfcoat.2013.07.019 SN - 0257-8972 VL - 235 SP - 97 EP - 107 PB - Elsevier B.V. AN - OPUS4-29729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Technische Prüfvorschriften für Fahrbahnübergänge aus Asphalt, TL/TP-ING - Teil 6, Abschnitt 7 N2 - Technische Lieferbedingungen und Technische Prüfvorschriften für Ingenieurbauten KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-343-3 VL - 780/3 SP - 1 EP - 26 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56218 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Technische Lieferbedingungen für die Baustoffe zur Herstellung von Fahrbahnübergängen aus Asphalt (TL ING, Teil 6, Abschnitt 7) N2 - TL BEL-FÜ Technische Lieferbedingungen für die Baustoffe zur Herstellung von Fahrbahnübergängen aus Asphalt TL/TP-Ing - Teil 6, Abschnitt 7 Technische Lieferbedingungen und Technische Prüfvorschriften für Ingenieurbauten KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-342-6 VL - 780/2 SP - 1 EP - 20 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Thomas A1 - Vierneusel, B. A1 - Gradt, Thomas A1 - Tremmel, S. A1 - Wartzack, S. A1 - Szücs, Z. A1 - Arendt, I. T1 - Optimierte MoS2-PVD-Schichten für wechselnde Umgebungsbedingungen N2 - Der Festschmierstoff Molybdändisulfid ist insbesondere für Extremanwendungen, bei denen konventionelle Öl- oder Fettschmierung nicht in Frage kommen (Vakuum, hohe Pressungen) ein gerne eingesetzter Werkstoff. Problematisch ist jedoch der negative Einfluss von Feuchtigkeit, wodurch die Einsetzbarkeit von M0S2 unter Normalbedingungen leidet. Bei mittels PVD-Verfahren abgeschiedenen MoSa-Schichten ergibt sich jedoch die Möglichkeit, durch Anpassung der Beschichtungsparameter vorwiegend basal ausgerichtete Schichten herzustellen, die auch an normal feuchter Luft ein verbessertes tribologisches Verhalten zeigen. MoSa-Schichten sind darüber hinaus auch für Anwendungen bei extrem tiefen Temperaturen interessant, da hier kein Schmierstoff zur Verfügung steht, der ähnlich günstige Reibeigenschaften aufweist. Für bewegliche Stützelemente zwischen supraleitenden Magnetspulen des Kernfusions-Experiments Wendelstein 7-X waren bis zu 7 pm dicke Schichten entwickelt worden, die jedoch durch das notwendige langsame Aufwachsen für andere Anwendungen nicht wirtschaftlich herzustellen waren. Hier sollen neue, im Rahmen eines Kooperationsprojekts entstandene MoS2-PVD-Schichten vorgestellt werden, die bei wechselnden Umgebungsbedingungen noch gute tribologische Eigenschaften liefern, jedoch durch ihre Dicke von 1-2 pm und hoher Aufwachsrate kostengünstig sind. N2 - The solid lubricant molybdenum disulfide is a well known material for extreme conditions where conventlonal oll or grease lubrication is not feasible (vacuum, high pressures). Problems arise due to a negative effect of humidity which is a drawback for the suitability of M0S2 under normal conditions. However, by using a PVD process, Deposition parameters can be optimized to gain coatings with a more textured structure orienting the basal planes parallel to the Substrate surface. Therefore, an improved tribological behavior even under moist conditions can be achieved. MoS2-coatings additionally are interesting candidates for being applied under cryogenic temperatures, since no lubricant is available having similarly favorable frictional properties. Up to 7 pm thick coatings have been developed especially for sliding support elements between superconducting magnets of the fusion-experiment Wendelstein 7-X, however, the extremely slow deposition rate precluded its utilization on more common tribo-systems due to cost considerations. Here, new MoS2-coatings are presented which were developed in a cooperational project, giving good tribological results under variing environments but are more cost effective being only 1-2 pm in thickness and faster in film growth.. T2 - 53. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß CY - Göttingen, Germany DA - 24.09.2012 PY - 2012 SN - 978-3-00-039201-6 SP - 46/1 EP - 46/12 CY - Aachen AN - OPUS4-26724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hickel, Tilmann A1 - Divinski, S. A1 - Starikov, S. A1 - Soisson, F. A1 - Mény, C. A1 - Hegde, O. A1 - Gerlitz, M. A1 - Magnifouet, G. A1 - Schneider, A. A1 - Barreteau, C. A1 - Mirebeau, I. A1 - Tran, V.T. A1 - Förster, G. A1 - Front, A. A1 - Egorov, A. A1 - Wilde, G. A1 - Amara, H. A1 - Hammerschmidt, T. A1 - Mrovec, M. A1 - Pierron-Bohnes, V. A1 - Drautz, R. A1 - Fu, C. T1 - Magnetism in iron alloys: methodological advances for thermodynamics, defects, and kinetics N2 - Steels are among the technologically and economically most relevant materials. Key innovations in important sectors of human society such as mobility, energy and safety, are currently based on alloying of Fe with other transition-metal elements such as Mn, Cr, or Co. Due to strong impacts and conceptual challenges related to magnetism, however, the fundamental understanding and the ability to computationally design these steels in high-throughput approaches lags behind other classes of alloys. In this article, we will provide a substantial review of the role of magnetism, magnetic excitations and transformations for alloy thermodynamics, point defects, interfaces and kinetics. This will be achieved by combining insights from different methods: Ab initio simulations have the advantage that the magnetic ground state is intrinsic part of the electronic minimization. Due to the coarsening of the many-electron structures and therewith magnetic interactions, tight-binding methods can handle larger system sizes. Effective interaction models provide the freedom to exploit more sophisticated magnetic interactions. The performance of these methods in terms of magnetic properties of Fe alloys will be evaluated by providing state-of-the-art results for their sensitivity to magnetism. Furthermore, dedicated experiments will be discussed to complete the understanding of magnetic effects in Fe alloys and to validate the modeling strategy. KW - Magnetic excitations KW - Defects KW - Diffusion KW - Density functional theory KW - Tight-binding KW - Effective interaction models PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634530 DO - https://doi.org/10.1515/ijmr-2023-0225 SN - 1862-5282 VL - 60 IS - 99 SP - 1 EP - 14761 PB - Walter de Gruyter GmbH AN - OPUS4-63453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Zusätzliche Technische Vertragsbedingungen und Richtlinien für Ingenieurbauten, Teil 6: Bauwerksausstattung, Abschnitt 7: Fahrbahnübergänge N2 - Die Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Ingenieurbauten (ZTV-ING) wurden zuletzt mit ARS Nr. 23/2021 vom 20. 10. 2021 mit dem Stand 2021/10 fortgeschrieben. Die jetzige Fortschreibung beinhaltet eine Gliederungsänderung des Regelwerks, um die für den Brückenbau relevanten Teile vorne gebündelt darstellen zu können. Eine Synopse hierzu ist der Anlage 4 zu entnehmen. „Wesentliche Änderungen in den ZTV-ING“ gegenüber der letzten Fassung sind der Anlage 3 zu entnehmen. In gleicher Weise sind die aktuellen „Hinweise zu den ZTV-ING — Stand 2022/01“ gemäß Anlage 2 einzubeziehen. Die Hinweise zu den entsprechenden Abschnitten der ZTV-ING sind bei der Projektbearbeitung und Ausschreibung zu beachten. Soweit die „Hinweise zu den ZTV-ING“ für die jeweilige Maßnahme zutreffend sind und vertragsrechtliche Bedeutung haben, sind entsprechende Textpassagen gesondert in die Vergabeunterlagen aufzunehmen bzw. zu vereinbaren. KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-344-0 VL - 782/7 SP - 1 EP - 30 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mi, W. A1 - Josephs, R. D. A1 - Melanson, J. E. A1 - Dai, X. A1 - Wang, Y. A1 - Zhai, R. A1 - Chu, Z. A1 - Fang, X. A1 - Thibeault, M.-P. A1 - Stocks, B. B. A1 - Meija, J. A1 - Bedu, M. A1 - Martos, G. A1 - Westwood, S. A1 - Wielgosz, R. I. A1 - Liu, Q. A1 - Teo, T. L. A1 - Liu, H. A1 - Tan, Y. J. A1 - Öztuğ, M. A1 - Saban, E. A1 - Kinumi, T. A1 - Saikusa, K. A1 - Schneider, Rudolf A1 - Weller, Michael G. A1 - Konthur, Zoltán A1 - Jaeger, Carsten A1 - Quaglia, M. A1 - Mussell, C. A1 - Drinkwater, G. A1 - Giangrande, C. A1 - Vaneeckhoutte, H. A1 - Boeuf, A. A1 - Delatour, V. A1 - Lee, J. E. A1 - O'Connor, G. A1 - Ohlendorf, R. A1 - Henrion, A. A1 - Beltrão, P. J. A1 - Naressi Scapin, S. M. A1 - Sade, Y. B. T1 - PAWG Pilot Study on Quantification of SARS-CoV-2 Monoclonal Antibody - Part 1 N2 - Under the auspices of the Protein Analysis Working Group (PAWG) of the Comité Consultatif pour la Quantité de Matière (CCQM) a pilot study, CCQM-P216, was coordinated by the Chinese National Institute of Metrology (NIM), National Research Council of Canada (NRC) and the Bureau International des Poids et Mesures (BIPM). Eleven Metrology Institutes or Designated Institutes and the BIPM participated in the first phase of the pilot study (Part 1). The purpose of this pilot study was to develop measurement capabilities for larger proteins using a recombinant humanized IgG monoclonal antibody against Spike glycoprotein of SARS-CoV-2 (Anti-S IgG mAb) in solution. The first phase of the study was designed to employ established methods that had been previously studies by the CCQM Protein Analysis Working Group, involving the digestion of protein down to the peptide or amino acid level. The global coronavirus pandemic has also led to increased focus on antibody quantitation methods. IgG are among the immunoglobulins produced by the immune system to provide protection against SARS-CoV-2. Anti-SARS-CoV-2 IgG can therefore be detected in samples from affected patients. Antibody tests can show whether a person has been exposed to the SARS-CoV-2, and whether or not they potentially show lasting immunity to the disease. With the constant spread of the virus and the high pressure of re-opening economies, antibody testing plays a critical role in the fight against COVID-19 by helping healthcare professionals to identify individuals who have developed an immune response, either via vaccination or exposure to the virus. Many countries have launched large-scale antibody testing for COVID-19. The development of measurement standards for the antibody detection of SARS-CoV-2 is critically important to deal with the challenges of the COVID-19 pandemic. In this study, the SARS-CoV-2 monoclonal antibody is being used as a model system to build capacity in methods that can be used in antibody quantification. Amino acid reference values with corresponding expanded uncertainty of 36.10 ± 1.55 mg/kg, 38.75 ± 1.45 mg/kg, 18.46 ± 0.78 mg/kg, 16.20 ± 0.67 mg/kg and 30.61 ± 1.30 mg/kg have been established for leucine, valine, phenylalanine, isoleucine and proline, respectively. Agreement between nearly all laboratories was achieved for the amino acid analysis within 2 to 2.5 %, with one participant achieving markedly higher results due to a technical issue found in their procedure; this result was thus excluded from the reference value calculations. The relatively good agreement within a laboratory between different amino acids was not dissimilar to previous results for peptides or small proteins, indicating that factors such as hydrolysis conditions and calibration procedures could be the largest sources of variability. Peptide reference values with corresponding expanded uncertainty of 4.99 ± 0.28 mg/kg and 6.83 ± 0.65 mg/kg have been established for ALPAPIEK and GPSVFPLAPSSK, respectively. Not surprisingly due to prior knowledge from previous studies on peptide quantitation, agreement between laboratories for the peptide-based analysis was slightly poorer at 3 to 5 %, with one laboratory's result excluded for the peptide GPSVFPLAPSSK. Again, this level of agreement was not significantly poorer than that achieved in previous studies with smaller or less complex proteins. To reach the main text of this paper, click on Final Report. KW - Antibody quantification KW - Amino acid analysis KW - Peptide analysis KW - Round robin test PY - 2021 DO - https://doi.org/10.1088/0026-1394/59/1a/08001 VL - 59 IS - 1A SP - 08001 AN - OPUS4-54972 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Devi, Sarita A1 - Goel, S. A1 - Rani, S. A1 - Schneider, Rudolf J. A1 - Rohilla, R. A1 - Kumari, Surbhi A1 - Prabhakar, N. T1 - MOF-metal nanohybrid-assisted charge transfer amplification for electrochemical biosensing of the MUC1 cancer biomarker N2 - Cancer is a severe disease characterized by high mortality and complex pathophysiology; however, its early and accurate diagnosis remains inadequate. Conventional diagnostic approaches often fall short, particularly for dense tissues, and are frequently invasive, costly, and of limited availability. This reinforces the need for a compact, economical, and ultrasensitive assay that is operationally simple and interpretable. We present an efficient electrochemical detection platform for the cancer biomarker mucin 1 (MUC1). A fluorine-doped tin oxide (FTO) surface was modified with an iron-based metal–organic framework (FeMOF) intercalated with palladium nanorods (PdNR). FeMOF was prepared using Fe3+/Fe2+ precursors at a 1.2/1 mmol ratio and dual ligands, i.e. tetrahydroxy-1,4-benzoquinone and 2-aminobenzene-1,4-dicarboxylic acid. AntiMUC1 antibodies were immobilized on a modified electrode via p-phenylenediamine (PDA) (FTO/FeMOF@PdNR/PDA/antiMUC1Ab) and evaluated using electrochemical impedance spectroscopy (EIS) and voltammetry. The designed sensor demonstrated an excellent binding affinity for the MUC1 antigen. Among these techniques, the EIS method stands out for its technical performance, as evidenced by the high sensitivity (detection limit 0.074 fg mL−1), quantification limit 0.24 fg mL−1, and high analytical sensitivity (1.39 × 103 Ω fg−1 mL−1 cm−2). The negligible cross-reactivity with interferent biomolecules, rapid response (10-minute equilibrium), regenerability up to 5 cycles, high reproducibility (RSD ∼1–3%), and long-term stability (up to 35 days) further validate the suitability of the proposed MUC1 immunosensor. This study presents an ultrasensitive biosensor that is compact, cost-effective, and easy for individuals at home to use after further development into a kit-based end product. Moreover, its excellent functionality for spiked serum samples shows promise for next-generation clinical diagnostics. KW - Antibodies KW - Metal-organic framework KW - Immunoassay PY - 2026 DO - https://doi.org/10.1039/D6AN00018E SP - 1 EP - 11 PB - Royal Society of Chemistry CY - London AN - OPUS4-65726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pereira, P.M.R. A1 - Carvalho, José Joao A1 - Silva, S. A1 - Cavaleiro, J.A.S. A1 - Schneider, Rudolf A1 - Fernandes, R. A1 - Tomé, J.P.C. T1 - Porphyrin conjugated with serum albumins and monoclonal antibodies boosts efficiency in targeted destruction of human bladder cancer cells N2 - The synthesis of a novel PS conjugated with bovine and human serum albumin (BSA and HSA) and a monoclonal antibody anti-CD104 is reported, as well as their biological potential against the human bladder cancer cell line UM-UC-3. No photodynamic effect was detected when the non-conjugated porphyrin was used. Yet, when it was coupled covalently with the mAb anti-CD104, BSA and HSA, the resulting photosensitizer conjugates demonstrated high efficacy in destroying the cancer cells, the mAb anti-CD104 efficacy overruling the albumins. KW - Rinderserumalbumin KW - BSA KW - Monoklonale Antikörper KW - Blasenkrebs KW - Konjugate KW - Conjugates KW - Therapeutische Antikörper KW - CD104 PY - 2014 DO - https://doi.org/10.1039/c3ob42082e SN - 1477-0520 SN - 1477-0539 VL - 12 IS - 11 SP - 1804 EP - 1811 PB - RSC CY - Cambridge AN - OPUS4-30451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kepsutlu, B. A1 - Wycisk, V. A1 - Achazi, K. A1 - Kapishnikov, S. A1 - Perez-Berna, A.J. A1 - Guttmann, P. A1 - Cossmer, Antje A1 - Pereiro, E. A1 - Ewers, H. A1 - Ballauff, M. A1 - Schneider, G. A1 - McNally, J.G. T1 - Cells Undergo Major Changes in the Quantity of Cytoplasmic Organelles after Uptake of Gold Nanoparticles with Biologically Relevant Surface Coatings N2 - Here, we use cryo soft X-ray tomography (cryo-SXT), which delivers 3D ultrastructural volumes of intact cells without chemical fixation or staining, to gain insight about nanoparticle uptake for nanomedicine. We initially used dendritic polyglycerol sulfate (dPGS) with potential diagnostic and therapeutic applications in inflammation. Although dPGS-coated gold nanoparticle (dPGS-AuNP) uptake followed a conventional endocytic/degradative pathway in human lung epithelial cell lines (A549), with cryo-SXT, we detected ∼5% of dPGS-AuNPs in the cytoplasm, a level undetectable by confocal light microscopy. We also observed ∼5% of dPGS-AuNPs in a rarely identified subcellular site, namely, lipid droplets, which are important for cellular energy metabolism. Finally, we also found substantial changes in the quantity of cytoplasmic organelles upon dPGS-AuNP uptake over the 1–6 h incubation period; the number of small vesicles and mitochondria significantly increased, and the number of multivesicular bodies and the number and volume of lipid droplets significantly decreased. Although nearly all organelle numbers at 6 h were still significantly different from controls, most appeared to be returning to normal levels. To test for generality, we also examined cells after uptake of gold nanoparticles coated with a different agent, polyethylenimine (PEI), used for nucleic acid delivery. PEI nanoparticles did not enter lipid droplets, but they induced similar, albeit less pronounced, changes in the quantity of cytoplasmic organelles. We confirmed these changes in organelle quantities for both nanoparticle coatings by confocal fluorescence microscopy. We suggest this cytoplasmic remodeling could reflect a more common cellular response to coated gold nanoparticle uptake. KW - Cellular trafficking KW - Confocal laser scanning microscopy KW - Cytoplasmic remodeling KW - Dendritic polyglycerol sulfate KW - Polyethylenimine KW - 3D ultrastructural analysis KW - Cryo-soft X-ray tomography PY - 2020 DO - https://doi.org/10.1021/acsnano.9b09264 VL - 14 IS - 2 SP - 2248 EP - 2264 AN - OPUS4-50464 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulze-Makuch, D. A1 - Haque, S. A1 - Beckles, D. A1 - Schmitt-Kopplin, P. A1 - Harir, M. A1 - Schneider, Beate A1 - Stumpp, C. A1 - Wagner, D. T1 - A chemical and microbial characterization of selected mud volcanoes in Trinidad reveals pathogens introduced by surface water and rain water N2 - Terrestrial mud volcanoes are unique structures driven by tectonic pressure and fluids from the deep subsurface. These structures are mainly found in active tectonic zones, such as the area near the Los Bajos Fault in Trinidad. Here we report a chemical and microbiological characterization of three mud volcanoes, which included analyses of multiple liquid and solid samples from the mud volcanoes. Our study confirms previous suggestions that at least some of the mud volcano fluids are a mixture of deeper salt-rich water and surficial/precipitation water. No apparent water quality differences were found between sampling sites north and south of a major geological fault line. Microbiological analyses revealed diverse communities, both aerobic and anaerobic, including sulfate reducers, methanogens, carbon dioxide fixing and denitrifying bacteria. Several identified species were halophilic and likely derived from the deeper salt-rich subsurface water, while we also cultivated pathogenic species from the Vibrionaceae, Enterobacteriaceae, Shewanellaceae, and Clostridiaceae. These microorganisms were likely introduced into the mud volcano fluids both from surface water or shallow ground-water, and perhaps to a more minor degree by rain water. The identified pathogens are a major health concern that needs to be addressed. KW - Water stable isotope analysis KW - Mud volcanoe fluids KW - Metabolomics PY - 2020 DO - https://doi.org/10.1016/j.scitotenv.2019.136087 VL - 707 SP - 136087 PB - Elsevier B.V. AN - OPUS4-50499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, S. A1 - Schneider, Ronald A1 - Faber, M.H. ED - Haukaas, T. T1 - Quantification of the value of structural health monitoring information for fatigue deteriorating structural systems N2 - This paper addresses the quantification of the value of structural health monitoring (SHM) before its implementation for structural systems on the basis of its Value of Information (VoI). The value of SHM is calculated utilizing the Bayesian pre-posterior decision analysis modelling the structural life cycle performance, the integrity management and the structural risks. The relevance and precision of SHM information for the reduction of the structural system risks and the expected cost of the structural integrity management throughout the life cycle constitutes the value of SHM and is quantified with this framework. The approach is focused on fatigue deteriorating structural steel systems for which a continuous resistance deterioration formulation is introduced. In a case study, the value of SHM for load monitoring is calculated for a Daniels system subjected to fatigue deterioration. The influence of and the value of SHM in regard to the structural system risks and the integrity management is explicated and explained. The results are pointing to the importance of the consideration of the structural system risks for the quantification of the value of SHM. T2 - ICASP 12 - 12th International conference on applications of statistics and probability in civil engineering CY - Vancouver, Canada DA - 12.07.2015 PY - 2015 DO - https://doi.org/10.14288/1.0076284 SP - Paper 605, 1 EP - 8 AN - OPUS4-34332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Ronald A1 - Fischer, J. A1 - Bügler, M. A1 - Nowak, M. A1 - Thöns, S. A1 - Borrmann, A. A1 - Straub, D. T1 - Assessing and updating the reliability of concrete bridges subjected to spatial deterioration - principles and software implementation N2 - Inspection and maintenance of concrete bridges is a major cost factor in transportation infrastructure, and there is significant potential for using information gained during inspection to update predictive models of the performance and reliability of such structures. In this context, this paper presents an approach for assessing and updating the reliability of prestressed concrete bridges subjected to chloride-induced reinforcement corrosion. The system deterioration state is determined based on a Dynamic Bayesian Network (DBN) model that considers the spatial variability of the corrosion process. The overall system reliability is computed by means of a probabilistic structural model coupled with the deterioration model. Inspection data are included in the system reliability calculation through Bayesian updating on the basis of the DBN model. As proof of concept, a software prototype is developed to implement the method presented here. The software prototype is applied to a typical highway bridge and the influence of inspection information on the system deterioration state and the structural reliability is quantified taking into account the spatial correlation of the corrosion process. This work is a step towards developing a software tool that can be used by engineering practitioners to perform reliability assessments of ageing concrete bridges and update their reliability with inspection and monitoring data. KW - Structural reliability KW - Dynamic Bayesian Networks KW - Spatial deterioration KW - Inspection KW - Monitoring general KW - Analysis and design methods KW - Reinforcement KW - Corrosion KW - Prestressed concrete PY - 2015 DO - https://doi.org/10.1002/suco.201500014 SN - 1464-4177 VL - 16 IS - 3 SP - 356 EP - 365 PB - Ernst & Sohn CY - Berlin AN - OPUS4-34336 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Schneider, S. A1 - Prediger, L. A1 - Flassenberg, G. ED - Hájek, P. ED - Tywoniak, J. ED - Lupísek, A. ED - Sojková, K. T1 - Sustainability analysis for the recycling of masonry T2 - CESB 13 - 3rd International conference Central Europe towards sustainable building - Sustainable building and refurbishment for next generations CY - Prague, Czech Republic DA - 2013-06-26 KW - Masonry KW - Recycling KW - Sustainability KW - LCA KW - LCC KW - LCWE PY - 2013 SN - 978-80-247-5015-6 SN - 978-80-247-5017-0 SP - 345 EP - 348 AN - OPUS4-30407 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Schneider, S. A1 - Brandstetter, C.P. A1 - Flassenberg, G. T1 - Stoffkreislauf im Mauerwerksbau - Nachhaltigkeitsanalyse für das Mauerwerksrecycling N2 - In Deutschland fallen nach Abschätzungen von jährlich bis zu 10 Millionen Tonnen Mauerwerkbruch an. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind diese Restmassen zukünftig einem möglichst hochwertigen und individuell angepassten Recycling zuzuführen. Vor diesem Hintergrund wurde im IGF-Forschungsvorhaben 17022 N der Forschungsvereinigung Porenbetonindustrie e.V. die Nachhaltigkeit verschiedener Recyclingoptionen für Mauerwerkbruch ganzheitlich untersucht. Unter Einbeziehung der Hauptmauersteinarten Ziegel, Kalksandstein, Porenbeton und Leichtbeton wurden dabei material- und verfahrenstechnische sowie ökologische, ökonomische und soziale Aspekte berücksichtigt. Als Ergebnis wurde ein EDV-gestütztes Analysetool (Web-Tool) zur Nachhaltigkeitsbewertung für das Mauerwerksrecycling entwickelt. Mit dem Web-Tool sollen Anwender (Planer, Architekten, Recycler) die Möglichkeit erhalten, für verschiedene Untersuchungsfälle unter Einbeziehung regional und sachlich bedingter Parameter objektspezifische Aussagen zur Nachhaltigkeit treffen zu können. Auf diesem Wege können im Sinne der aktuellen gesetzlichen Vorgaben nachhaltige Stoffkreisläufe im Mauerwerksbau geschlossen und somit letztlich die Deponierung von Mauerwerksrestmassen reduziert oder gar vermieden werden. T2 - R'13 - Fachtagung Recycling CY - Weimar, Germany DA - 19.09.2013 PY - 2013 SP - 1 EP - 6 PB - Bauhaus-Univ. CY - Weimar AN - OPUS4-30408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Stephan A1 - Hanelt, S. A1 - Canitz, C. A1 - Hoffmann, Holger A1 - Garbe, L.-A. A1 - Schneider, Rudolf T1 - Entwicklung monoklonaler Antikörper gegen Diclofenac N2 - Diclofenac (DCF) wird als nicht-steroidales, antientzündliches Arzneimittel gegen Fieber, Entzündungen, rheumatische Erkrankungen und Schmerzen eingesetzt. 70 % werden nach Einnahme wieder ausgeschieden. Aufgrund unvollständiger Elimination in den Kläranlagen lassen sich Rückstände im Trinkwasser und im Oberflächengewässer nachweisen. Diclofenac wird in der Umweltanalytik v.a. mittels GC-MS oder LCMS nachgewiesen. Bioanalytische Methoden machen sich die spezifische Antigen-Antikörper-Wechselwirkung zunutze, so z.B. Immunoassays. Die hierfür erforderlichen Antikörper werden durch Immunisierung mit einem Konjugat aus dem Analyten und einem Trägerprotein gewonnen. Die Kopplung kann direkt über die Carboxylfunktion von Diclofenac erfolgen. Um Abschirmungseffekte zu vermeiden, kann zwischen Protein und Analy1 ein Spacer sinnvoll sein. PY - 2015 SN - 1618-3258 SN - 1617-5301 IS - 4 SP - 107 EP - 109 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-35241 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schneider, Ronald A1 - Fischer, J. A1 - Straub, D. A1 - Thöns, S. A1 - Bügler, M. A1 - Borrmann, A. T1 - Intelligente Bauwerke - Prototyp zur Ermittlung der Schadens- und Zustandsentwicklung für Elemente des Brückenmodells N2 - Dieser Bericht beschreibt ein Systemmodell für eine integrale Ermittlung und Prognose der Schadens- und Zustandsentwicklung der Elemente eines Brückensystems unter Berücksichtigung von Ergebnissen aus Inspektionen und Überwachung. Das Systemmodell wurde anhand eines ausgesuchten Spannbetonüberbaus in einzelliger Kastenbauweise entwickelt. Es besteht aus zwei integralen Teilmodellen: ein Modell zur Beschreibung des Systemschädigungszustandes und ein Modell zur Beschreibung der Standsicherheit. Für die Modellierung des stochastischen Systemschädigungszustandes eines Brückensystems werden dynamische Bayes'sche Netze (DBN) vorgeschlagen. Dieser Ansatz ermöglicht es, alle relevanten Schädigungsprozesse und deren stochastische Abhängigkeiten zu berücksichtigen. Ein wesentlicher Vorteil dieses Ansatzes ist es, dass DBN ideal dafür geeignet sind, Bayes'sche Aktualisierungen auf Grundlage von Informationen aus Inspektionen und Überwachungsmaßnahme auf eine effiziente und robuste Art und Weise durchzuführen. Der DBN-Ansatz ist deshalb für die Entwicklung von Software für das Erhaltungsmanagement von alternden Brückenbauwerken, die vom Benutzer keine vertieften Kenntnisse der Zuverlässigkeitstheorie verlangt, ideal geeignet. Für die Modellierung der Standsicherheit eines alternden Kastenträgers wird vereinfachend Biegeversagen des globalen Längssystems betrachtet. Zur Berechnung der maximalen Traglast eines Kastenträgers infolge des Systemschädigungszustandes wird ein plastisch-plastisches Verfahren eingesetzt, wobei die Beanspruchungen mittels der Fließgelenktheorie unter Ausnutzung der plastischen Beanspruchbarkeit der Querschnitte des Kastenträgers ermittelt werden. Ein Kastenträger versagt, wenn sich durch die Ausbildung einer ausreichend großen Anzahl von Fließgelenken eine kinematische Kette ausbildet. Dieser Modellierungsansatz berücksichtigt Redundanzen, die sich aus der plastischen Beanspruchbarkeit der Querschnitte und der statischen Unbestimmtheit eines Kastenträgers ergeben. Zum Nachweis der praktischen Einsetzbarkeit des entwickelten Systemmodells wurde ein Software-Prototyp entwickelt, der eine intuitiv benutzbare graphische Benutzeroberfläche (Front-End) mit einem Berechnungskern (Back-End) koppelt. Die aktuelle Version des Software-Prototyps implementiert ein Modell der chloridinduzierten Bewehrungskorrosion und ein Tragwerksmodell, welches das Verfahrens der stetigen Laststeigerung zur Bestimmung der maximalen Traglast des Kastenträgers auf der Grundlage eines Finite-Elemente-Modells umsetzt. Zur Durchführung von Bayes'schen Aktualisierungen des Systemschädigungszustandes auf der Grundlage des DBN-Modells implementiert der Prototyp den Likelihood-Weighting-Algorithmus. Die entwickelte Architektur des Prototyps ermöglicht eine Erweiterung der Software um weitere Schädigungsprozesse. Der entwickelte Software-Prototyp ermöglicht Benutzern ohne vertiefte Kenntnisse der Zuverlässigkeitstheorie eine Berechnung des Einflusses von Bauwerksinformationen auf den Systemschädigungszustand und die Tragsicherheit eines Kastenträgers. Auf dieser Grundlage können effiziente Inspektions- und Überwachungsmaßnahmen identifiziert und das Erhaltungsmanagement optimiert werden. KW - Bridge KW - Condition survey KW - Damage KW - Deterioration KW - Development KW - Digital model KW - Durability KW - Engineering structure KW - Expert system KW - Forecast KW - Germany KW - Propability KW - Prototype KW - Reinforced concrete KW - Research report KW - Software KW - Stability KW - Stochastic process PY - 2015 UR - http://bast.opus.hbz-nrw.de/volltexte/2015/1615/ SN - 978-3-95606-190-5 SN - 0943-9293 VL - 117 SP - 1 EP - 74 PB - Carl Schünemann Verlag GmbH CY - Bergisch Gladbach AN - OPUS4-35193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raysyan, Anna A1 - Galvidis, I. A. A1 - Schneider, Rudolf A1 - Eremin, S. A. A1 - Burkin, M. A. T1 - Development of a latex particles-based lateral flow immunoassay for group determination of macrolide antibiotics in breast milk N2 - A lateral flow immunoassay (LFIA) using latex particles labeled with antibody to BSAclarithromycin (CLA) was developed for the rapid simultaneous group determination of six macrolide antibiotics. Optimization of antigen spotting on the membrane and latex probe loading allowed improving visual detectability (vLOD) 100 times, which was 1, 1, 10, 10, 50, and 1000 ng/mL for CLA, roxithromycin, erythromycin, dirithromycin, azithromycin, and oleandomycin in buffer, respectively. The calculated limits of instrumental detection (cLOD) were respectively 0.12, 0.15, 1.4, 2.1, 2.4, and 3.3 ng/mL. To avoid a strong influence of breast milk of a very diverse and variable composition, a sample pretreatment is proposed. The six macrolides mentioned can be visually detected in breast milk after 20 minutes pretreatment at concentrations of 10-1000 ng / ml or instrumentally with cLOD of 4.0, 2.5, 30, 42, 42 and 180 ng/mL. The recovery rate from the spiked samples carried out using a strip scanner device ranged from 71% to 110%, and precision expressed as relative standard deviation was between 3-14%. The described rapid on-site diagnostic assay format can be useful for monitoring the content of antibiotics in breast milk during macrolide treatment to ensure safe breastfeeding of infants. KW - Clarithromycin KW - Roxithromycin KW - Erythromycin KW - Dirithromycin KW - Azithromycin KW - Oleandomycin KW - Macrolide antibiotics KW - Makrolide KW - Antibiotika PY - 2020 DO - https://doi.org/10.1016/j.jpba.2020.113450 SN - 0731-7085 VL - 189 IS - 113450 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam, NL AN - OPUS4-51343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raysyan, Anna A1 - Moerer, R. A1 - Coesfeld, Bianca A1 - Eremin, S. A1 - Schneider, Rudolf T1 - Fluorescence polarization immunoassay for the determination of diclofenac in wastewater N2 - Pharmacologically active compounds are often detected in wastewater and surface waters. The nonsteroidal anti-inflammatory drug diclofenac (DCF) was included in the European watch list of substances that requires its environmental monitoring in the member states. DCF may harmfully influence the ecosystem already at concentrations ≤ 1 μg L−1. The fast and easy quantification of DCF is becoming a subject of global importance. Fluorescence polarization immunoassay (FPIA) is a homogeneous mix-and-read method which does not require the immobilization of reagents. FPIA can be performed in one phase within 20–30 min, making it possible to analyse wastewater without any complicated pre-treatment. In this study, new tracermolecules with different structures, linking fluorophores to derivatives of the analyte, were synthesized, three homologous tracers based on DCF, two including a C6 spacer, and one heterologous tracer derived from 5-hydroxy-DCF. The tracer molecules were thoroughly assessed for performance. Regarding sensitivity of the FPIA, the lowest limit of detection reached was 2.0 μg L−1 with a working range up to 870 μg L−1. The method was validated for real wastewater samples against LC-MS/MS as reference method with good agreement of both methods. KW - Abwasser KW - Umweltschadstoffe KW - Antikörper KW - Antibody PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-518398 DO - https://doi.org/10.1007/s00216-020-03058-w SN - 1618-2642 VL - 413 IS - 4 SP - 999 EP - 107 PB - Springer CY - Heidelberg AN - OPUS4-51839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scala-Benuzzi, M. L. A1 - Soler-Illia, G. J. A. A. A1 - Rabia, J. A1 - Battaglini, F. A1 - Schneider, Rudolf A1 - Pereira, S. V. A1 - Messina, G. A. T1 - Immunosensor based on porous gold and reduced graphene platform for the determination of EE2 by electrochemical impedance spectroscopy N2 - In this work, we report an electrochemical immunosensor to detect ethinylestradiol in water samples, using electrochemical impedance spectroscopy (EIS) as a detection technique. For the development of this immunosensor, the direct modification of the working electrode of a screen-printed carbon electrode was carried out. First, to reduce the resistance of the electrode, electroreduced graphene was incorporated on the surface. Second, a porous gold structure was electrodeposited on reduced graphene by electrodeposition and the dynamic hydrogen bubble template assisted method. Thus, a marked increase in surface area was obtained for anti-EE2 antibodies immobilization. Subsequently, the specific anti-EE2 antibodies were covalently immobilized using α-lipoic acid for attaching them to the gold surface. The electrode modified with the antibodies was incubated for 30 min in the samples containing EE2, producing the specific Antigen antibody binding. As the charge transfer resistance of a redox probe in the electrode surface is governed by the surface blocking effects, the charge transfer resistance was related to the amount of EE2 captured to realize a quantitative determination. For this, the EIS measurements were performed in a 4 mM [Fe(CN)6]4−/3− solution in 0.1 M KCl. The obtained Nyquist diagrams were adjusted using the Randles circuit as an equivalent circuit to obtain the corresponding resistances. The developed methodology showed good selectivity, precision, and sensitivity; although the LOD obtained was higher than those presented in other published articles, it turned out to be an alternative that allows the determination of ethinylestradiol using a simple disposable electrode. KW - Ethinylestradiol KW - Biosensor KW - Elektrochemisch KW - Impedanz PY - 2021 DO - https://doi.org/10.1016/j.jelechem.2021.115604 SN - 1572-6657 VL - 897 SP - 115604 EP - 115611 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-54048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Florian, Camilo A1 - Fischer, Daniel A1 - Freiberg, K. A1 - Duwe, M. A1 - Sahre, Mario A1 - Schneider, S. A1 - Hertwig, Andreas A1 - Krüger, Jörg A1 - Rettenmayr, M. A1 - Beck, Uwe A1 - Undisz, A. A1 - Bonse, Jörn T1 - Single Femtosecond Laser-Pulse-Induced Superficial Amorphization and Re-Crystallization of Silicon N2 - Superficial amorphization and re-crystallization of silicon in <111> and <100> orientation after irradiation by femtosecond laser pulses (790 nm, 30 fs) are studied using optical imaging and transmission electron microscopy. Spectroscopic imaging ellipsometry (SIE) allows fast data acquisition at multiple wavelengths and provides experimental data for calculating nanometric amorphous layer thickness profiles with micrometric lateral resolution based on a thin-film layer model. For a radially Gaussian laser beam and at moderate peak fluences above the melting and below the ablation thresholds, laterally parabolic amorphous layer profiles with maximum thicknesses of several tens of nanometers were quantitatively attained. The accuracy of the calculations is verified experimentally by high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (STEM-EDX). Along with topographic information obtained by atomic force microscopy (AFM), a comprehensive picture of the superficial re-solidification of silicon after local melting by femtosecond laser pulses is drawn. KW - Femtosecond laser KW - Silicon KW - Amorphization KW - Crystallization KW - Spectroscopic imaging ellipsometry PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-523687 UR - https://www.mdpi.com/1996-1944/14/7/1651 DO - https://doi.org/10.3390/ma14071651 SN - 1996-1944 VL - 14 IS - 7 SP - 1651-1 EP - 1651-21 PB - MDPI AG CY - Basel, Switzerland AN - OPUS4-52368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, J. A1 - Farris, L. A1 - Nolze, Gert A1 - Reinsch, Stefan A1 - Cios, G. A1 - Tokarski, T. A1 - Thompson, S. T1 - Microstructure evolution in Inconel 718 produced by powder bed fusion additive manufacturing N2 - Inconel 718 is a precipitation strengthened, nickel-based super alloy of interest for the Additive Manufacturing (AM) of low volume, complex parts to reduce production time and cost compared to conventional subtractive processes. The AM process involves repeated rapid melting, solidification and reheating, which exposes the material to non-equilibrium conditions that affect elemental segregation and the subsequent formation of solidification phases, either beneficial or detrimental. These variations are difficult to characterize due to the small length scale within the micron sized melt pool. To understand how the non-equilibrium conditions affect the initial solidification phases and their critical temperatures, a multi-length scale, multi modal approach has been taken to evaluate various methods for identifying the initial phases formed in the as-built Inconel 718 produced by laser-powder bed fusion (L-PBF) additive manufacturing (AM). Using a range of characterization tools from the bulk differential thermal analysis (DTA) and x-ray diffraction (XRD) to spatially resolved images using a variety of electron microscopy tools, a better understanding is obtained of how these minor phases can be properly identified regarding the amount and size, morphology and distribution. Using the most promising characterization techniques for investigation of the as-built specimens, those techniques were used to evaluate the specimens after various heat treatments. During the sequence of heat treatments, the initial as-built dendritic structures recrystallized into well-defined grains whose size was dependent on the temperature. Although the resulting strength was similar in all heat treated specimens, the elongation increased as the grain size was refined due to differences in the precipitated phase distribution and morphology. KW - Metal additive manufacturing KW - Inconel 718 KW - Heat treatment KW - Grain boundary precipitates KW - Laves phase PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-542758 DO - https://doi.org/10.3390/jmmp6010020 SN - 2504-4494 VL - 6 IS - 1 SP - 1 EP - 20 PB - MDPI CY - Basel AN - OPUS4-54275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Rudolf A1 - He, Y. A1 - Zhu, R. A1 - Cai, Y. A1 - Zhang, Y. A1 - Zhang, Y. A1 - Pan, S. A1 - Zhang, Y. T1 - Transcriptomics and protein biomarkers reveal the detoxifying mechanisms of UV radiation for nebivolol toward zebrafish (Danio rerio) embryos/larvae N2 - Nebivolol (NEB), a β-blocker frequently used to treat cardiovascular diseases, has been widely detected in aquatic environments, and can be degraded under exposure to UV radiation, leading to the formation of certain transformation products (UV-TPs). Thus, the toxic effects of NEB and its UV-TPs on aquatic organisms are of great importance for aquatic ecosystems. In the present study, the degradation pathway of NEB under UV radiation was investigated. Subsequently, zebrafish embryos/larvae were used to assess the median lethal concentration (LC50) of NEB, and to clarify the sub-lethal effects of NEB and its UV-TPs for the first time. It was found that UV radiation could reduce the toxic effects of NEB on the early development of zebrafish. Transcriptomic analysis identified the top 20 enriched Kyoto Encyclopedia of Genes and Genomes (KEGG) pathways in zebrafish larvae exposed to NEB, most of which were associated with the antioxidant, nervous, and immune systems. The number of differentially expressed genes (DEGs) in the pathways were reduced after UV radiation. Furthermore, the analysis of protein biomarkers, including CAT and GST (antioxidant response), AChE and ACh (neurotoxicity), CRP and LYS (immune response), revealed that NEB exposure reduced the activity of these biomarkers, whereas UV radiation could alleviate the effects. The present study provides initial insights into the mechanisms underlying toxic effects of NEB and the detoxification effects of UV radiation on the early development of zebrafish. It highlights the necessity of considering the toxicity of UV-TPs when evaluating the toxicity of emerging pollutants in aquatic systems. KW - Biomarker KW - Pharmazeutika KW - Toxikologie KW - UV Bestrahlung KW - Zebrafisch KW - Transformationsprodukte PY - 2022 DO - https://doi.org/10.1016/j.aquatox.2022.106241 SN - 0166-445X VL - 249 SP - 1 EP - 10 PB - Elsevier CY - Amsterdam AN - OPUS4-55559 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gregório, Bruno J.R. A1 - Ramos, Inês I. A1 - Marques, Sara S. A1 - Barreiros, Luísa A1 - Magalhães, Luís M. A1 - Schneider, Rudolf A1 - Segundo, Marcela A. T1 - Microcarrier-based fluorescent yeast estrogen screen assay for fast determination of endocrine disrupting compounds N2 - The presence of endocrine-disrupting compounds (EDCs) in water poses a significant threat to human and animal health, as recognized by regulatory agencies throughout the world. The Yeast Estrogen Screen (YES) assay is an excellent method to evaluate the presence of these compounds in water due to its simplicity and capacity to assess the bioaccessible forms/fractions of these compounds. In the presence of a compound with estrogenic activity, Saccharomyces cerevisiae cells, containing a lacZ reporter gene encoding the enzyme β-galactosidase, are induced, the enzyme is synthesised, and released to the extracellular medium. In this work, a YES-based approach encompassing the use of a lacZ reporter gene modified strain of S. cerevisiae, microcarriers as solid support, and a fluorescent substrate, fluorescein di-β-D-galactopyranoside, is proposed, allowing for the assessment of EDCs’ presence after only 2 h of incubation. The proposed method provided an EC50 of 0.17 ± 0.03 nM and an LLOQ of 0.03 nM, expressed as 17β-estradiol. The assessment of different EDCs provided EC50 values between 0.16 and 1.2 × 103 nM. After application to wastewaters, similar results were obtained for EDCs screening, much faster, compared to the conventional 45 h spectrophotometric procedure using a commercial kit, showing potential for onsite high-throughput screening of environmental contamination. KW - Biosensoren KW - YES assay KW - Endokrine Disruptoren PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-602315 DO - https://doi.org/10.1016/j.talanta.2024.125665 VL - 271 SP - 1 EP - 7 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-60231 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tamschick, S. A1 - Rozenblut-Kościsty, B. A1 - Ogielska, M. A1 - Lehmann, Andreas A1 - Lymberakis, P. A1 - Hoffmann, F. A1 - Lutz, I. A1 - Schneider, Rudolf A1 - Kloas, W. A1 - Stöck, M. T1 - Impaired gonadal and somatic development corroborate vulnerability differences to the synthetic estrogen ethinylestradiol among deeply diverged anuran lineages N2 - Amphibians are undergoing a global decline. One poorly investigated reason could be the pollution of aquatic habitats by endocrine disrupting compounds (EDCs). We tested the susceptibility to the synthetically stabilized estrogen 17α-ethinylestradiol (EE2) in three deeply diverged anuran species, differing in sex determination systems, types of gonadogenesis and larval ecologies. To understand whether data from the amphibian model Xenopus laevis (Pipidae) are analogous and applicable to only distantly related non-model amphibians, tadpoles of X. laevis, Hyla arborea (Hylidae) and Bufo viridis (Bufonidae) were simultaneously exposed to 50, 500 and 5000 ng/L EE2 from hatching until completion of metamorphosis, using a flow-through-system under identical experimental conditions. Comparing molecularly established genetic with histologically assessed phenotypic sex in all species, we have recently shown that EE2 provoked numerous genetic-male-to-phenotypic-female sex reversals and mixed sex individuals, confirming overall its expected feminizing effect. In the present study, we focus on the influence of EE2 on gonadal and somatic development. Anatomy and histology revealed several species-specific effects. In both non-model species, H. arborea and B. viridis, high numbers of anatomically impaired gonads were observed. In H. arborea, exposed to 5000 ng/L EE2, numerous underdeveloped gonads were detected. Whereas EE2 did not alter snout-to-vent length and body weight of X. laevis metamorphs, H. arborea showed a treatment-dependent decrease, while B. viridis exhibited an increase in body weight and snout-to-vent length. Apart from a concentration-dependent occurrence of yellowish skin color in several H. arborea, no organ-specific effects were detected. Since EE2 ubiquitously occurs in many aquatic ecosystems and affects sexual and somatic development, among EDCs, it may indeed contribute to amphibian decline. The inter-species variation in developmental EE2-effects corroborates species-specific vulnerability differences towards EDCs between deeply diverged amphibian groups KW - Endocrine disruption KW - Ethinylestradiol KW - Mass spectrometry PY - 2016 DO - https://doi.org/10.1016/j.aquatox.2016.07.001 SN - 0166-445X SN - 1879-1514 VL - 177 SP - 503 EP - 514 PB - Elsevier AN - OPUS4-37633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Rudolf A1 - Carvalho, A. M. A1 - Manicardi, A. A1 - Montes, C. V. A1 - Gunnoo, S. B. A1 - Madder, A. T1 - Decoration of trastuzumab with short oligonucleotides: synthesis and detailed characterization N2 - Trastuzumab (Herceptin) is an FDA-approved therapeutic antibody currently employed in the treatment of metastatic stages of breast cancer. Herein, we propose a simple, fast and cost-effective methodology to conjugate trastuzumab with 22-mer 5' thiol-modified oligonucleotides using a bifunctional crosslinker. The conjugates were successfully characterized by MALDI-ToF MS and SDS-PAGE, obviating the need for enzymatic digestion and difficult chromatographic separations. Furthermore, ELISA was performed to ensure that trastuzumab activity is not affected by oligonucleotide conjugation. KW - MALDI-ToF KW - ELISA PY - 2017 DO - https://doi.org/10.1039/c7ob02216f SN - 1477-0539 VL - 15 IS - 42 SP - 8923 EP - 8928 AN - OPUS4-43328 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Rudolf A1 - Korsak, B. A1 - Almeida, G. M. A1 - Rocha, S. A1 - Pereira, C. A1 - Mendes, N. A1 - Osorio, H. A1 - Pereira, P. M. A1 - Rodrigues, J. M. M. A1 - Sarmento, B. A1 - Tome, J. P. C. A1 - Oliveira, C. T1 - Porphyrin modified trastuzumab improves efficacy of HER2 targeted photodynamic therapy of gastric cancer N2 - Gastric cancer (GC) is the 3rd deadliest cancer worldwide, due to limited treatment options and late diagnosis. Human epidermal growth factor receptor-2 (HER2) is overexpressed in similar to 20% of GC cases and anti-HER2 antibody trastuzumab in combination with conventional chemotherapy, is recognized as standard therapy for HER2-positive metastatic GC. This strategy improves GC patients' survival by 2-3 months, however its optimal results in breast cancer indicate that GC survival may be improved. A new photoimmunoconjugate was developed by conjugating a porphyrin with trastuzumab (Trast: Porph) for targeted photodynamic therapy in HER2-positive GC. Using mass spectrometry analysis, the lysine residues in the trastuzumab structure most prone for porphyrin conjugation were mapped. The in vitro data demonstrates that Trast: Porph specifically binds to HER2-positive cells, accumulates intracellularly, co-localizes with lysosomal marker LAMP1, and induces massive HER2-positive cell death upon cellular irradiation. The high selectivity and cytotoxicity of Trast: Porph based photoimmunotherapy is confirmed in vivo in comparison with trastuzumab alone, using nude mice xenografted with a HER2-positive GC cell line. In the setting of human disease, these data suggest that repetitive cycles of Trast: Porph photoimmunotherapy may be used as an improved treatment strategy in HER2-positive GC patients. KW - Photoimmunotherapy KW - Photoimmunoconjugate KW - Gastric cancer PY - 2017 DO - https://doi.org/10.1002/ijc.30844 SN - 0020-7136 VL - 141 IS - 7 SP - 1478 EP - 1489 PB - International Journal of Cancer AN - OPUS4-43315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hakim, I. A1 - Schumacher, David A1 - Sundar, V. A1 - Donaldson, S. A1 - Creuz, A. A1 - Schneider, R. A1 - Keller, J. A1 - Browning, C. A1 - May, D. A1 - Abo Ras, M. A1 - Meyendorf, N. ED - Chimenti, D. E. ED - Bond, L. J. T1 - Volume imaging NDE and serial sectioning of carbon fiber composites N2 - A composite material is a combination of two or more materials with very different mechanical, thermal and electrical properties. The various forms of composite materials, due to their high material properties, are widely used as structural materials in the aviation, space, marine, automobile, and sports industries. However, some defects like voids, delamination, or inhomogeneous fiber distribution that form during the fabricating processes of composites can seriously affect the mechanical properties of the composite material. In this study, several imaging NDE techniques such as: thermography, high frequency eddy current, ultrasonic, x-ray radiography, x-ray laminography, and high resolution x-ray CT were conducted to characterize the microstructure of carbon fiber composites. Then, a 3D analysis was implemented by the destructive technique of serial sectioning for the same sample tested by the NDE methods. To better analyze the results of this work and extract a clear volume image for all features and defects contained in the composite material, an intensive comparison was conducted among hundreds of 3D-NDE and multi serial sections’ scan images showing the microstructure variation. T2 - 44TH ANNUAL REVIEW OF PROGRESS IN QUANTITATIVE NONDESTRUCTIVE EVALUATION CY - Provo, Utah, USA DA - 16.07.2017 KW - Carbon fiber reinforced polymers KW - Non-destructive testing KW - Thermography KW - Eddy current KW - Ultrasound KW - X-ray radiography KW - X-ray laminography KW - X-ray computed tomography KW - Serial sectioning PY - 2018 DO - https://doi.org/10.1063/1.5031590 VL - 1949 SP - 120003-1 EP - 120003-10 PB - AIP Publishing AN - OPUS4-45173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sin, DWM. A1 - Wong, YC. A1 - Lehmann, Andreas A1 - Schneider, Rudolf A1 - Kakoulides, E. A1 - Lin, TT. A1 - Liu, QD. A1 - Cabillic, J. A1 - Lardy-fontan, S. A1 - Nammoonnoy, J. T1 - CCQM-K126: low polarity organic in water: carbamazepine in surface water N2 - This study aimed to assess the measurement capabilities of participating National Metrology Institutes/ Designated Institutes (NMIs/DIs) and expert laboratories in determining of low-polarity organics in surface water. This comparison was organized by Government Laboratory, Hong Kong (GLHK). At the CCQM Organic Analysis Working Group (OAWG) Meeting held in November 2012 in Hong Kong, GLHK initially proposed a CCQM key comparison and a parallel pilot study programme on pharmaceuticals in surface water. Further discussion at the CCQM Meeting held in April 2014 in Paris, the OAWG approved a CCQM Track C comparison (CCQM-K126) on low polarity pharmaceuticals in surface water. In the meeting, the programme was supported by more than six National Metrology Institutes/ Designated Institutes (NMIs/ DIs). CCQM-K126 officially commenced in July 2014 and had registration from nine NMIs/DIs. Participants were provided two bottles (40 mL each) of surface water and were requested to determine the mass fraction of spiked carbamazepinein in surface water. The coordinator received nine sets of results from eight NMIs/DIs in February 2015. Apart from one using an immunoassay technique, all participants applied isotope dilution liquid chromatography-tandem mass spectrometry (ID-LCMS/MS) technique as their determination technique. KW - CCQM-K126 KW - ELISA KW - Mass spectrometry PY - 2017 DO - https://doi.org/10.1088/0026-1394/54/1A/08030 SN - 0026-1394 SN - 1681-7575 VL - 54 IS - Suppl. S SP - Article 08030, 1 EP - 56 PB - IOP Publ. CY - Bristol AN - OPUS4-44831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Rübner, Katrin A1 - Schneider, S. A1 - Beck, T. A1 - Flassenberg, G. A1 - Herbst, Tristan T1 - Stoffkreislauf im Mauerwerksbau - Nachhaltigkeitsanalyse für das Mauerwerksrecycling / Schlussbericht zum IGF-Vorhaben 17022 N N2 - In Deutschland fallen mittelfristig erhebliche Mengen von Mauerwerkbruch an. Aus dem jährlichen Bauschuttanfall und den Produktionszahlen von Wandbausteinen lassen sich die Mengen an Mauerwerksrestmassen ableiten, die als Rückbaumaterial bei Abriss-, Umbau und Sanierungsarbeiten in Deutschland anfallen werden. Hiernach ist pro Jahr mit bis zu 10 Millionen Tonnen heute vornehmlich heterogen anfallendem Mauerwerkbruch zu rechnen [1a]. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind diese Restmassen zukünftig einem möglichst hochwertigen Recycling zuzuführen. In diesem Spannungsfeld führt die deutsche Mauersteinindustrie das breit aufgestellte gemeinschaftliche Forschungsprojekt "SIM Stoffkreislauf im Mauerwerksbau" durch. In insgesamt acht mauersteinübergreifenden IGFForschungsvorhaben wurden und werden technisch orientierte Lösungsmöglichkeiten für das Recycling von Mauerwerk erarbeitet und Anwendungsbereiche für Mauerwerksrestmassen aufgezeigt. Eine grundsätzliche Entscheidung über die Eignung von Mauerwerksrestmassen für bestimmte Recyclingwege kann es letztlich nicht geben. Es wird immer eine Einzelfallentscheidung bleiben, die wesentlich durch komplexe technische sowie ökologische und ökonomische Randbedingungen geprägt wird. Vor diesem Hintergrund wurde im Rahmen des IGF-Forschungsvorhabens 17022 N der Forschungsvereinigung Porenbetonindustrie e.V., Berlin die Nachhaltigkeit verschiedener Recyclingoptionen für Mauerwerkbruch ganzheitlich untersucht und bewertet. Unter Einbeziehung der Hauptwandbausteinarten Ziegel, Kalksandstein, Porenbeton und Leichtbeton wurden dabei material- und verfahrenstechnische sowie ökologische, ökonomische und soziale Aspekte berücksichtigt. Auf Grundlage der gewonnenen Erkenntnisse wurde ein EDV-gestütztes Analysetool (Web-Tool) zur Nachhaltigkeitsbewertung für das Mauerwerksrecycling entwickelt. Mit dem Web-Tool sollen Anwender (Planer, Architekten, Recycler) die Möglichkeit erhalten, für verschiedene Untersuchungsfälle unter Einbeziehung regional und sachlich bedingter Parameter, wie Materialqualität, Stoffmengen, Logistik, Aufbereitungstechnik, Anwendungsbereiche, Kosten und Erlöse, objektspezifische Aussagen zur Nachhaltigkeit treffen zu können. Auf diesem Wege können im Sinne der aktuellen gesetzlichen Vorgaben nachhaltige Stoffkreisläufe im Mauerwerksbau geschlossen und somit letztlich die Deponierung von Mauerwerksrestmassen vermieden werden. Alle vier Wandbaustoffarten haben sich im Rahmen des Forschungsvorhabens als recyclingfähig und hinsichtlich der Nachhaltigkeit als gleichwertig erwiesen. Das Ziel des Vorhabens wurde damit erreicht. KW - Nachhaltigkeit KW - Mauerwerkbruch KW - Ganzheitlichkeit PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-288572 SP - 1 EP - 182 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-28857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Pitters, S. A1 - Wedel, F. A1 - Hindersmann, I. T1 - Developing a guideline for structural health monitoring of road bridges in Germany N2 - In recent years, Structural Health Monitoring (SHM) has become a useful and increasingly widely used tool for supporting lifetime extensions of existing bridges with known structural deficiencies or indications of potentially critical damages or damage processes. At the same time, methods and tools are emerging, which enable monitoring-informed predictive maintenance of new and existing bridges based on digital twins. The monitoring process – starting from the definition of monitoring actions and ending with decisions based on monitoring outcomes – is complex and requires expertise in structural engineering, operation and maintenance of bridges, metrology, and data analytics. To support German road authorities, engineering consultancies, building contractors and other stakeholders of the bridge management, the Federal Highway Research Institute (BASt) has initiated the development of a new guideline for applying SHM as part of the management of road bridges. The guideline will present various use cases and for each identified use case, it will propose a proven monitoring scheme. In addition, the guideline will provide guidance on assessing the benefits of SHM as well as a common approach to managing monitoring data as a systematic basis for integrating monitoring data in the bridge management. This contribution discusses the motivation, objectives, and scope of the guideline, describes its use case centric structure and outlines the proposed data management. T2 - IABMAS 2024 CY - Kopenhagen, Danmark DA - 24.06.2024 KW - Guideline KW - Structural health monitoring KW - Road bridges KW - Infrastructure PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613947 SN - 978-1-032-77040-6 DO - https://doi.org/10.1201/9781003483755-236 SP - 2009 EP - 2017 PB - CRC Press AN - OPUS4-61394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wedel, F. A1 - Pitters, S. A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Hille, Falk A1 - Hindersmann, I. T1 - Guideline for the strategic application of monitoring of road bridges in Germany N2 - Engineering structures are an important part of our transport infrastructure. Their failure is associated with high safety risks and economic damage. Ensuring the availability of these constructions and guaranteeing their operational safety are thus important tasks. Currently, maintenance of engineering structures is a reactive process and therefore not yet a predictive process. Every 3 to 6 years, the structures are visually inspected, all damages are documented and a condition grade is assigned to the structure based on the detected damages. Continuous data-providing methods such as monitoring are used only very occasionally. With the help of monitoring, condition data about the structures are continuously collected, which can be used for a better assessment of the structures. On the one hand, this would increase safety of engineering structures, and on the other hand, it makes the shift towards predictive maintenance management based on real-time data and predictions, where the onset of damage is detected before it occurs, possible in the first place. Monitoring plays therefore an important role in the management of the infrastructure. It is a crucial a step towards the digitalisation of our infrastructure and existing processes. Although there are many use cases for monitoring that have already been successfully implemented, monitoring is not yet widely used by German road authorities due to several challenges that were also identified within the scope of the project. Therefore, a guide has been developed in which the current obstacles related to monitoring are identified and possibilities for integrating monitoring into existing processes are offered. To ensure optimal alignment with the needs of road authorities, both an online survey and a workshop have been conducted. The results are summarised in a brochure that is made available to authorities to improve the use of monitoring in Germany. This paper presents the guideline and the brochure. T2 - 10th European Workshop on Structural Health Monitoring (EWSHM 2024) CY - Potsdam, Germany DA - 10.06.2024 KW - Verkehrsinfrastrukturen KW - Engineering Structures KW - Bridges KW - Structural Health Monitoring KW - Guideline PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612821 UR - https://www.ndt.net/search/docs.php3?id=29582 DO - https://doi.org/10.58286/29582 SN - 1435-4934 VL - 29 IS - 7 SP - 1 EP - 8 PB - NDT.net GmbH & Co. KG CY - Mayen AN - OPUS4-61282 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Pitters, S. A1 - Ramasetti, Eshwar Kumar A1 - Schneider, Ronald A1 - Wedel, F. A1 - Hindersmann, I. ED - Rogge, Andreas ED - Meng, Birgit T1 - Föderiertes Datenmanagement von Monitoringdaten aus Structural Health Monitoring Anwendungen und daraus gewonnenen Trainingsdaten bei Spannbetonbrücken N2 - Beim Structural Health Monitoring entstehen eine Vielzahl von Daten, Metadaten und Modellen mit hohem Wert für die Beurteilung des Bauwerkszustands und der Prognose von Veränderungen. Kontinuierlich anwachsende Datenbestände müssen nachhaltig geteilt, genutzt und über die Bauwerkslebensdauer archiviert werden. Dabei stellen die Vielfalt der Messaufgaben, die Heterogenität der Daten, die dezentrale Erfassung und z. T. der Umfang eine Herausforderung für die beteiligten Akteure dar. Für den Datentransfer der Monitoringdaten zwischen der Straßenbauverwaltung und den Monitoringausführenden wird ein flexibles Abstimmungsverfahren vorgeschlagen und ein Lösungskonzept für ein föderiertes Datenmanagement skizziert. Eine weitere Herausforderung stellt die bauwerksübergreifende Zusammenstellung von Trainingsdaten für konkrete KI-Anwendungen dar. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Structural Health Monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612902 SN - 978-3-9818564-7-7 SP - 178 EP - 185 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Pitters, S. A1 - Hindersmann, I. A1 - Schneider, Ronald A1 - Wedel, F. ED - Rogge, Andreas ED - Meng, Birgit T1 - Leitfaden für den strategischen Einsatz von Monitoring an Straßenbrücken N2 - Für die Anwendung von Structural Health Monitoring (SHM) im Rahmen des Managements von Straßenbrü-cken wurde zur Unterstützung von Straßenbauverwaltungen, Ingenieurbüros, Bauunternehmen und weiteren Akteuren die Erstellung eines Leitfadens initiiert. Dieser Leitfaden stellt typische Anwendungsfälle für Monito-ring vor und schlägt für diese bewährte Herangehensweisen vor. Darüber hinaus bietet der Leitfaden Empfeh-lungen für Ausschreibung und Vergabe von Monitoringleistungen, eine Anleitung zur Bewertung des wirt-schaftlichen Nutzens von SHM, Hinweise zur optimal einsetzbaren Messtechnik sowie einen Ansatz für das Datenmanagement zur Integration der Monitoringdaten in das Brückenmanagement. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Leitfaden KW - Monitoring KW - Straßenbrücke PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612931 SN - 978-3-9818564-7-7 SP - 186 EP - 191 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Patrick A1 - Helmrich, M. A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Baeßler, Matthias A1 - Lorelli, S. A1 - Morgenthal, G. T1 - Maintalbrücke Gemünden: Bauwerksmonitoring und -identifikation aus einem Guss T1 - Maintalbrücke Gemünden – Integrated structural health monitoring and UAS diagnostics N2 - Die Infrastruktursysteme der Industriestaaten erfordern heute und in Zukunft ein effizientes Management bei alternder Bausubstanz, steigenden Lasten und gleichbleibend hohem Sicherheitsniveau. Digitale Technologien bieten ein großes Potenzial zur Bewältigung der aktuellen und künftigen Herausforderungen im Infrastrukturmanagement. Im BMBF-geförderten Projekt Bewertung alternder Infrastrukturbauwerke mit digitalen Technologien (AISTEC) wird untersucht, wie unterschiedliche Technologien und deren Verknüpfung gewinnbringend eingesetzt werden können. Am Beispiel der Maintalbrücke Gemünden werden ein sensorbasiertes Bauwerksmonitoring, bildbasierte Inspektion mit durch Kameras ausgestatteten Drohnen (UAS) und die Verknüpfung digitaler Bauwerksmodelle umgesetzt. Die aufgenommenen Bilder dienen u. a. als Grundlage für spätere visuelle Anomaliedetektionen und eine 3D-Rekonstruktion, welche wiederum für die Kalibrierung und Aktualisierung digitaler Tragwerksmodelle genutzt werden. Kontinuierlich erfasste Sensordaten werden ebenfalls zur Kalibrierung und Aktualisierung der Tragwerksmodelle herangezogen. Diese Modelle werden als Grundlage für Anomaliedetektionen und perspektivisch zur Umsetzung von Konzepten der prädiktiven Instandhaltung verwendet. Belastungsfahrten und historische Daten dienen in diesem Beitrag der Validierung von kalibrierten Tragwerksmodellen. N2 - Infrastructure systems of industrialised countries today and in the future require efficient management with an ageing stock, increasing loads while simultaneously maintaining a high level of safety. Digital technologies offer great potential for the current and future challenges in infrastructure management. The BMBF-funded project AISTEC is investigating how the individual technologies and their interconnection can be used beneficially. With the Maintalbrücke in Gemünden as an exemplary application, sensor-based structural monitoring, image-based inspection using unmanned aircraft systems (UAS) equipped with cameras and the integration of digital structural models are being implemented. The recorded images serve, among others, as basis for subsequent anomaly detection and a 3D reconstruction, which in turn are used for updating digital structural models. Continuously recorded sensor data is used to update the parameters of the structural models, which in turn provide the basis for predictive maintenance. Load tests are used to validate the models. KW - Bauwerksüberwachung KW - Strukturmonitoring KW - Structural Health Monitoring KW - Modell-Update KW - UAS KW - Belastungstest KW - Structural system identification KW - Structural health monitoring KW - Model update KW - UAS KW - Load tests PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-554924 DO - https://doi.org/10.1002/bate.202100102 SN - 0932-8351 VL - 99 IS - 3 SP - 163 EP - 172 PB - Ernst & Sohn CY - Berlin AN - OPUS4-55492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald A1 - Thöns, S. A1 - Fischer, J. A1 - Bügler, M. A1 - Borrmann, A. A1 - Straub, D. T1 - A software prototype for assessing the reliability of a concrete bridge superstructure subjected to chloride-induced reinforcement corrosion N2 - A software prototype is developed for assessing and updating the reliability of single-cell prestressed concrete box girders subjected to chloride-induced reinforcement corrosion. The underlying system model consists of two integrated sub-models: a condition model for predicting the deterioration state of the box girder and a structural model for evaluating the overall system reliability. The condition model is based on a dynamic Bayesian network (DBN) model which considers the spatial variation of the corrosion process. Inspection data are included in the calculation of the system reliability through Bayesian updating on the basis of the DBN model. To demonstrate the effect of partial inspections, the software prototype is applied to a case study of a typical highway bridge with six spans. The case study illustrates that it is possible to infer the condition of uninspected parts of the structure due to the spatial correlation of the corrosion process. T2 - IALCCE 2014 - 4th International symposium on life-cycle civil engineering CY - Tokyo, Japan DA - 16.11.2014 PY - 2015 SN - 978-1-138-00120-6 SP - 846 EP - 853 PB - Taylor & Francis CY - London AN - OPUS4-32220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöther, N. A1 - Wang, S. A1 - Wosniok, Aleksander A1 - Glötzl, R. A1 - Schneider-Glötzl, J. ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Distributed Brillouin sensing in optical fibers: Soil displacement monitoring using sensor-equipped geogrids N2 - This paper reports on the application of distributed Brillouin fiber optic sensing to the monitoring of geotechnical structures. The presented approach to Brillouin sensing offers an alternative to the common pulse-based measurements by using the frequency domain analysis. The focus of the research and field-testing work is to collect reliable structural health monitoring data from large-scale structures while preserving the System’s versatility in terms of being suitable for different application environments (soil structures, foundations, concrete construction works, pipelines etc.) and its robustness in being well functioning in harsh environments. Upon reviewing the presented application test, it is concluded that Brillouin frequency domain based monitoring, when applied to geotechnical structures, is capable of providing accurate strain readings representing deformations of the soil body, and reliable temperature readings for generating temperature profiles of the entire structure. An overview of the frequency domain analysis of Brillouin sensing and its digital implementation is given, along with the experiences and insights drawn from an open field test of sensor-equipped geogrid mats. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Structural health monitoring KW - Distributed sensing KW - Fiber-optic sensing KW - Brillouin sensing KW - Strain and temperature measurements KW - Sensor-equipped geosynthetics PY - 2013 SN - 978-962-367-768-4 SP - 290 EP - 295 AN - OPUS4-29914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Recknagel, Christoph A1 - Alte-Teigeler, R. A1 - Bergmann, F.-J. A1 - Gebhards, G. A1 - Grabe, W. A1 - Guse, J. A1 - Hartel, S. A1 - Huth, P. A1 - Jannicke, B. A1 - Lobach, T. A1 - Schneider, T. A1 - Sondermann, E. A1 - Vengels, D. A1 - Voß, M. A1 - Willand, E. ED - Roßbach, W. T1 - Technische Lieferbedingungen für Fugenfüllstoffe in Verkehrsflächen TL Fug-StB 15 N2 - Nach mehr als 15-jähriger Anwendung und mit der zwischenzeitlichen Einführung europäisch harmonisierter Normen für Fugenmaterialien war eine Anpassung Qualitäts- und Gütesicherungsanforderungen für Fugenfüllungen im Bundesfernstraßenbereich erforderlich. Hierbei ging es insbesondere darum, Maßnahmen und Verfahren zu entwickeln, um das nationale Qualitäts- und Gütesicherungsniveau weiter zu entwickeln und weiterhin sicher stellen zu können. Nach den Untersuchungserfahrungen im Labor und im Feld ging darum, neuartige Material- und Stoffkombinationen qualitätssicher dem Bauprozess zur Verfügung stellen zu können. Erforderliche Anforderungskriterien und zulässige Toleranzen der Lieferqualität wurden neu gefasst. Es wurde ein Verfahren entwickelt, europäische Bauprodukte qualitätsgesichert in den Bauprozess im Bundesfernstraßenbericht zu überführen. KW - Baustoffe KW - Fugenfüllsysteme KW - Anforderungs- und Leistungsrichtlinien PY - 2015 SN - 978-3-86446-163-7 SP - 1 EP - 39 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-37221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Weise, Matthias ED - Uhlmann, E. T1 - Ellipsometrische Codierung & Fabry-Perot Schichtsysteme mit offenen, versteckten und forensischen Merkmalen zur Produkt-Authentifizierung T2 - 3. Internationaler Kongress - Sichere Identität CY - Berlin, Deutschland DA - 2011-04-05 KW - Ellipsometric encoding KW - Fabry-Perot layer stacks KW - Product authentification PY - 2011 SP - 1 EP - 4(?) CY - Berlin AN - OPUS4-23306 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liang, S. A1 - Schneider, Rudolf T1 - Capillary zone electrophoresis of cowpea mosaic virus and peak identification KW - Cowpea mosaic virus KW - CZE KW - MALDI-TOF-MS KW - Peak identification KW - Two electrophoretic forms PY - 2009 DO - https://doi.org/10.1002/elps.200800468 SN - 0173-0835 VL - 30 IS - 9 SP - 1572 EP - 1578 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-19447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Santos, S. A1 - Costa, C. A. E. A1 - Duarte, A. C. A1 - Scherer, H. W. A1 - Schneider, Rudolf A1 - Esteves, V. I. A1 - Santos, E. B. H. T1 - Influence of different organic amendments on the potential availability of metals from soil: A study on metal fractionation and extraction kinetics by EDTA N2 - The effects of long-term application of different organic amendments, as compared to mineral fertilizer, on Zn, Cu and Pb content and leachability in a luvisol derived from loess were assessed. The organic fertilizers, applied since 1962, were compost (COM) – from green organic household waste, sewage sludge (SLU) – from municipal water treatment facilities, farmyard manure (FYM) and the doses applied since 1997 were 90 t ha-1, 10 t ha-1 and 9 t ha-1, once in 3 years, respectively. The kinetics of metals extraction with 0.05 mol dm-3 EDTA at pH 6.0 has been studied. The two first-order reactions model was fitted to the kinetic data and allowed to distinguish two pools for each metal: a 'labile' fraction (Q1), quickly extracted with a rate constant k1, and a 'moderately labile' fraction (Q2), more slowly extracted, with a rate constant k2. Simultaneously, the pseudo-total metal contents in the soil samples were determined after digestion with aqua regia (3:1 HCl + HNO3). The obtained parameters Q1, k1, Q2, k2, for the kinetics of extraction of each metal in the three replicates of each fertilization mode, as well as the pseudo-total metal contents, were statistically analysed. COM and SLU application resulted in an increase of the total contents of Pb, Zn and Cu in soil. Further, the percentage of labile Zn and Pb also increased in consequence of the application of those amendments, particularly COM. The increase was more noticeable for Zn. FYM, despite not increasing the total content of Pb, Zn or Cu, did also have an effect on the leachability of Zn and Pb, increasing their labile fraction in soil. These results point to a potential risk of increasing metals mobility in soil, mainly Zn, associated to the use of organic amendments, particularly COM or SLU. KW - Compost KW - Sewage sludge KW - Soils KW - Metal mobility KW - EDTA KW - Kinetics PY - 2010 DO - https://doi.org/10.1016/j.chemosphere.2009.11.008 SN - 0045-6535 SN - 0366-7111 VL - 78 IS - 4 SP - 389 EP - 396 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-22187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Otto, A.H. A1 - Schrader, S. A1 - Steiger, Thomas A1 - Schneider, M. T1 - Gas-phase deprotonation energies of sulfuric acid, perchloric acid, chlorosulfuric acid and fluorosulfuric acid PY - 1997 SN - 0956-5000 VL - 93 IS - 22 SP - 3927 EP - 3930 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-2679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Almagro, J.-F. A1 - Busch, P. A1 - Gohil, D. D. A1 - Saunders, S. R. J. A1 - Sloof, W. G. A1 - Thiot, J.-F. A1 - Schneider, H. A1 - Whitwood, M. A1 - Wirth, Thomas T1 - Electron-Probe MICROanalysis of LighT Elements - Measurement Methods and Certified Reference Materials (MICROLITE) PY - 2000 IS - 266 SP - 1 EP - 35 PB - National Physical Laboratory CY - Teddington, Middlesex AN - OPUS4-6843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beck, Uwe A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Sahre, Mario A1 - Weise, Matthias T1 - Fabry-Perot-based layer stacks for ellipsometric encoding - Embedded public, hidden, and forensic information for product authentication N2 - Public, hidden, and forensic features either encoded or directly legible are used for authentication. Fabry-Perot layer stacks as information carriers in combination with imaging ellipsometry as optical read-out system provide all-in-one anti-counterfeiting capability that may establish the new security level 'encoded forensic'. Different layer designs are described with regard to all three security levels: public features (e.g. color and tilt effect) perceptible by the human eye, hidden features (e.g. spectroscopic response in the UV or IR), and forensic features (ellipsometric quantities Ψ and Δ as a function of wavelength λ and angle of incidence AOI). Physically uncloneable functions (PUF) could be realized as a result of a multi-material and a multi-parameter deposition approach as well as by means of specific design features of the Fabry-Perot layer stack. Hence, they are not subject to any reverse engineering strategies. Examples of stratified, micro-structured, and laser-modified Fabry-Perot layer systems are considered that may be used at all perception levels (e.g. human eye, bar code reader, and imaging ellipsometry) for authentication against product counterfeiting and related areas. -------------------------------------------------------------------------------------------------------------------- Zur Authentifizierung werden offene, versteckte und forensische Merkmale entweder codiert oder direkt auslesbar verwendet. Mit Fabry-Perot Schichtsystemen als Informationsträger in Kombination mit der abbildenden Ellipsometrie als optischem Auslesesystem steht ein 'all-in-one' Fälschungsschutz-System zur Verfügung, das ein neues Sicherheitsniveau 'kodiert-forensisch' darstellt. Es werden unterschiedliche Schichtdesigns beschrieben, mit denen alle drei Sicherheitsniveaus realisiert werden können: offene Merkmale (z.B. Farbe und Kippeffekt), die mit dem menschlichen Auge wahrnehmbar sind, versteckte Merkmale (z.B. die spektrale Antwort im Sichtbaren oder im IR) sowie forensische Merkmale (ellipsometrische Größen Ψ und Δ als Funktion der Wellenlänge λ und des Einfallswinkels AOI). Physikalisch nicht klonbare Funktionen (PUF) können im Ergebnis einer Multi-Material- und Multi-Parameter Beschichtungsstrategie sowie durch spezifische Design-Merkmale des Fabry-Perot Schichtsystems realisiert werden. Folglich sind solche Schichtsysteme dem 'reverse engineering' nicht zugänglich. Es werden Beispiele für lateral ausgedehnte, mikrostrukturierte und Laser modifizierte Schichtsysteme auf verschiedenen Ausleseniveaus (menschliches Auge, Barcode-Lesegerät, abbildendes Ellipsometer) vorgestellt, die zur Authentifizierung von Produkten und verwandte Gebiete geeignet sind. KW - Fabry-Perot Schichten KW - Ellipsometrie KW - Produkt- und Markenschutz PY - 2012 DO - https://doi.org/10.1002/vipr.201200494 SN - 0947-076X SN - 1522-2454 VL - 24 IS - 4 SP - 6 EP - 11 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-26180 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, S. T1 - Sustainability assessment for the recycling of masonry T2 - 6th Society & Materials International Conference SAM-6 CY - Leuven, Belgium DA - 2012-05-30 PY - 2012 AN - OPUS4-26151 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Beck, T. A1 - Flassenberg, G. A1 - Schneider, S. A1 - Eden, W. T1 - SIM Stoffkreislauf im Mauerwerksbau - Nachhaltigkeitsanalyse für das Mauerwerksrecycling T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2012-09-12 PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-1090 - 2-1097 AN - OPUS4-26540 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Weise, Matthias T1 - Optical layer systems for product authentication: interference, scattering, light diffusion and ellipsometric encoding as public, hidden and forensic security features N2 - Embedding of information on surfaces is state of the art for identification testing in which public, hidden and forensic features are used. In many instances, the legal authentication of a product, a material or a document is required. Among the surface-based encoded labels, bar codes and data matrices are most frequently applied. They are publicly visible. The material itself is irrelevant, only a sufficient optical contrast is required. However, a strong material dependence of the label can be achieved by means of Fabry-Perot layer stacks. Stack designs are described with regard to all three security levels: public features (e.g. color and tilt effect) perceptible by the human eye, hidden features (e.g. optical response in a given spectral range) detectable by commonly available instruments and forensic features (ellipsometric quantities Ψ and Δ as a function of wavelength λ and angle of incidence AOI) only detectable by sophisticated instruments. Regarding material-correlated authentication, ellipsometric quantities Ψ and Δ are used as encoded forensic features for the first time. Hence, Fabry-Perot layer stacks as information carriers in combination with imaging ellipsometry as optical read-out system provide all-in-one anti-counterfeiting capabilities. T2 - PSE 2012 - 13th International conference on plasma surface engineering CY - Garmisch-Partenkirchen, Germany DA - 10.09.2012 KW - Fabry-Perot layers KW - Ellipsometry KW - Anti-counterfeiting PY - 2012 UR - http://www.pse-conferences.net/tl_files/pse2012/abstractupload/PSE2012-PO1001-ext.pdf SP - 1 EP - 4 AN - OPUS4-27304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Herbst, Tristan A1 - Schneider, S. A1 - Beck, T. A1 - Flassenberg, G. T1 - Nachhaltigkeitsanalyse für das Mauerwerksrecycling PY - 2013 SN - 978-3-433-03017-2 SN - 978-3-433-60296-6 SN - 0170-4958 VL - 38 IS - Kap. 2.2.7 SP - 641 EP - 645 PB - Ernst & Sohn AN - OPUS4-28565 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, S. A1 - Herbst, Tristan A1 - Lenz, K. A1 - Wittstock, B. A1 - Bos, U. A1 - Sedlbauer, K. T1 - Recycling options for masonry - Identifying sustainable solutions N2 - Almost 15% of the average yearly waste accumulation in Germany originates from construction waste. It mainly comprises mineral materials such as concrete and different types of stonework, like lime-sandstone, red brick, aerated concrete and lightweight concrete. Due to the heterogeneous material composition, this kind of waste often ends up in landfill or can only be used for lower-level recycling. The AiF (German Federation of Industrial Research Association) funded the national research project "Sustainability Analysis for the Recycling of Masonry" in order to show different recycling opportunities for masonry as well as respective required technologies with regard to potential occurring mineral material mixtures. Technologies identified are for example such ones to break masonry into smaller grain sizes and technologies to separate the masonry into single material fractions. Furthermore, the project has the objective to assess the sustainability performance of various recycling options. These options and the related recycling routes are evaluated regarding environmental, economic and social aspects - all three pillars of sustainability - by using the methods of Life Cycle Assessment (LCA), Life Cycle Costing (LCC) and Life Cycle Working Environment (LCWE). The results are provided within a web-tool for operators of recycling facilities and for demolition companies. Its modular concept affords an individual sustainability assessment by several input options, like machine capacity, investment costs and achievable revenues. The tool enables the user to assess and compare different recycling opportunities concerning environmental, economic and social aspects in relation to identified material compositions and technologies applied. T2 - sb13 munich - Sustainable building conference CY - Munich, Germany DA - 24.04.2013 KW - Sustainability KW - LCA KW - LCC KW - LCWE KW - Recycling KW - Demolition material PY - 2013 SN - 978-3-8167-8965-9 SP - 387 EP - 388 PB - Fraunhofer IRB-Verl. AN - OPUS4-28639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Thieme-Hack, M. A1 - Berghaus, U. A1 - Brümmer, F. A1 - Elsner, U. A1 - Färber, C. A1 - Frank, D. A1 - Illgas, M. A1 - Kalbe, Ute A1 - Kathage, J. A1 - Leers, A. A1 - Müller, B. A1 - Röger-Göpfert, C. A1 - Russland, H.-J. A1 - Schnabel, B. A1 - Schneider, O. A1 - Schockmann, D. A1 - Schomakers, H. A1 - Schwalbe, D. A1 - Stegemann, D. A1 - van den Berg, T. A1 - Kramps, S. T1 - Fachbericht Kunststoffsportböden - Nachhaltige Kunststoffbelagsauswahl für Sportfreianlagen N2 - Kunststoff- und Kunststoffrasenflächen kommt bei intensiv genutzten Flächen als Allwetterbeläge eine große Bedeutung zu. Sie leisten einen wichtigen Beitrag zur Absicherung eines ganzjähriger Sportangebote. Gerade Kunststoffrasen ist aber in den letzten Jahren häufig in die Kritik geraten, insbesondere durch gefährliche Inhaltsstoffe und andere negative Einflüsse auf die Umwelt. Dies hat bei Bauherren zu einer Verunsicherung geführt und Fragen aufgeworfen, die erst teilweise beantwortet sind. Die Diskussionen rund um diesen Allwetterbelag haben bereits dazu geführt, dass von Seiten der Industrie viel verändert wurde und neue innovative Lösungen gefunden werden. Der Fachbericht stellt eine Handreichung für Fachleute und interessierte Laien dar, um mehr Klarheit besonders hinsichtlich der Umweltanforderungen zu erzielen. KW - Kunststoffsportbeläge KW - Kunstrasen KW - Umweltverträglichkeit KW - Schadstofftransfer KW - Mikroplastik PY - 2022 UR - https://shop.fll.de/de/fachbericht-kunststoffsportboeden-broschuere.html SP - 1 EP - 70 PB - Forschungsgesellschaft Landschaftsentwicklung Landschaftsbau (FLL) CY - Bonn AN - OPUS4-54390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Recknagel, Christoph A1 - Alte-Teigeler, R. A1 - Bergmann, F.-J. A1 - Gebhards, G. A1 - Grabe, W. A1 - Guse, J. A1 - Hartel, S. A1 - Huth, P. A1 - Jannicke, B. A1 - Lobach, T. A1 - Schneider, T. A1 - Sondermann, E. A1 - Vengels, D. A1 - Voß, M. A1 - Willand, E. ED - Roßbach, W. T1 - Zusätzliche Technische Vertragsbedingungen und Richtlinien für Fugen in Verkehrsflächen ZTV Fug-StB 15 N2 - Unter Berücksichtigung praktischer und wissenschaftlich-technischer Erkenntnisse der letzten 15 Jahre - insbesondere auch auf der Basis verschiedener BAM-Forschungsergebnisse und Zulassungsverfahren - erfolgte eine Überarbeitung der Grundlagen, Bauprinzipien, Ausführungs- und Einbaukriterien sowie der Zulassungs- und Gütesicherungsmaßnahmen für insgesamt 4 Bauarten von Fugenfüllsystemen für hochbeanspruchte Verkehrsflächen. In diesem - für den Bundesfernstraßenbereich verbindlichen bautechnischen Regelwerk - finden insbesondere auch die Ergebnisse mehrerer wissenschaftlicher Vorhaben der BAM bezüglich labortechnischer Untersuchungen und Felduntersuchungen zum Funktionsverhalten und zur Dauerhaftigkeit erste baurechtliche Konsequenzen. Auf der Basis von Untersuchungen u.a. im Brückenbau wurden Regelungen für die Fugenausbildung in Asphalt und bei Befestigungskombinationen erarbeitet und umgesetzt. Damit konnten umfassende Regelungen für die maßgebenden Fahrbahnbeläge im Bundesfernstraßenbereich der Straßenbauverwaltung und ausführenden Industrieunternehmungen zur Verfügung gestellt werden. Die Neufassung dieser Regelungen dient darüber hinaus dem Ziel, den von der BAM vertretenen Wechsel hin zu einer performance-bezogenen Bewertungsmethodik, vorzubereiten. KW - Baustoffe KW - Fugen KW - Betonstraßen PY - 2015 SN - 978-3-86446-162-0 SP - 1 EP - 50 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-37220 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Anker, Andy S. A1 - Aspuru-Guzik, Alán A1 - Ben Mahmoud, Chiheb A1 - Bennett, Sophie A1 - Briling, Ksenia R. A1 - Changiarath, Arya A1 - Chong, Sanggyu A1 - Collins, Christopher M. A1 - Cooper, Andrew I. A1 - Crusius, Daniel A1 - Darmawan, Kevion K. A1 - Das, Basita A1 - David, Nicholas A1 - Day, Graeme M. A1 - Deringer, Volker L. A1 - Duarte, Fernanda A1 - Eardley-Brunt, Annabel A1 - Evans, Matthew L. A1 - Evans, Rob A1 - Fairlamb, Ian A1 - Franklin, Barnabas A. A1 - Frey, Jeremy A1 - Ganose, Alex M. A1 - Goulding, Mark A1 - Hafizi, Roohollah A1 - Hakkennes, Matthijs A1 - Hickey, Niamh A1 - James, Gillian A1 - Jelfs, Kim E. A1 - Kalikadien, Adarsh V. A1 - Kapil, Venkat A1 - Koczor-Benda, Zsuzsanna A1 - Krammer, Ferdinand A1 - Kulik, Heather J. A1 - Kumar, Vishank A1 - Kuttner, Christian A1 - Lam, Erwin A1 - Lou, Yuchen A1 - Mante, Eltjo A1 - Martin, Jennie A1 - Mroz, Austin M. A1 - Nematiaram, Tahereh A1 - Pare, Charles W. P. A1 - Patra, Sarbani A1 - Proudfoot, James A1 - Ruscic, Branko A1 - Ryder, Matthew R. A1 - Sakaushi, Ken A1 - Saßmannshausen, Jörg A1 - Savoie, Brett M. A1 - Schneider, Nadine A1 - Schwaller, Philippe A1 - Skjelstad, Bastian Bjerkem A1 - Sun, Wenhao A1 - Szczypiński, Filip T. A1 - Torrisi, Steven A1 - Ueltzen, Katharina A1 - Vishnoi, Shubham A1 - Walsh, Aron A1 - Wang, Xinwei A1 - Wilson, Chloe A1 - Wu, Ruiqi A1 - Zeitler, Jakob T1 - Discovering structure–property correlations: General discussion N2 - This article is a discussion of the paper "Web-BO: Towards increased accessibility of Bayesian optimisation (BO) for chemistry" by Austin M. Mroz, Piotr N. Toka, Ehecatl Antonio del Río Chanona and Kim E. Jelfs (Faraday discussions, 2025, 256, 221-234). KW - Materials design KW - Machine learning KW - Automation KW - Materials discovery PY - 2025 DO - https://doi.org/10.1039/d4fd90062f SN - 1359-6640 SN - 1364-5498 VL - 256 IS - Themed collection: Data-driven discovery in the chemical sciences SP - 373 EP - 412 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-62208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Leubner, S. A1 - Schneider, Ralf A1 - Dubavik, A. A1 - Hatami, Soheil A1 - Gaponik, N. A1 - Resch-Genger, Ute A1 - Eychmüller, A. T1 - Influence of the stabilizing ligand on the quality, signal-relevant optical properties, and stability of near-infrared emitting Cd1-xHgxTe nanocrystals N2 - Bright and stable near-infrared (NIR) and infrared (IR) emitting chromophores are in high demand for applications in telecommunication, solar cells, security barcodes, and as fluorescent reporters in bioimaging studies. The best choice for wavelengths >750 nm are semiconductor nanocrystals, especially ternary or alloy nanocrystals like CdHgTe, which enable size and composition control of their optical properties. Here, we report on the influence of growth time and surface chemistry on the composition and optical properties of colloidal CdHgTe. Up to now, these are the only NIR and IR emissive quantum dots, which can be synthesized in high quality in water, using a simple one-pot reaction. For this study we utilized and compared three different thiol ligands, thioglycolic acid (TGA), 3-mercaptopropionic acid (MPA), and glutathione (GSH). Aiming at the rational design of bright NIR- and IR-emissive alloy materials, special emphasis was dedicated to a better understanding of the role of the surface ligand and adsorption–desorption equilibria on the photoluminescence quantum yield and stability. In this respect, dilution and protonation studies were performed. Our results show that with this simple synthetic procedure, strongly fluorescent CdHgTe colloids can be obtained with MPA as stabilizing ligand revealing quantum yields as high as 45% independent of particle concentration. PY - 2014 DO - https://doi.org/10.1039/c4tc00582a SN - 2050-7526 SN - 2050-7534 VL - 2 IS - 25 SP - 5011 EP - 5018 PB - Royal Soc. of Chemistry CY - Cambridge AN - OPUS4-31073 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Ralf A1 - Weigert, Florian A1 - Lesnyak, V. A1 - Leubner, S. A1 - Lorenz, T. A1 - Behnke, Thomas A1 - Dubavik, A. A1 - Joswig, J.-O. A1 - Resch-Genger, Ute A1 - Gaponik, N. A1 - Eychmüller, A. ED - Resch-Genger, Ute ED - Schneider, Ralf T1 - pH and concentration dependence of the optical properties of thiol-capped CdTe nanocrystals in water and D2O N2 - The optical properties of semiconductor nanocrystals (SC NCs) are largely controlled by their size and surface chemistry, i.e., the chemical composition and thickness of inorganic passivation shells and the chemical nature and number of surface ligands as well as the strength of their bonds to surface atoms. The latter is particularly important for CdTe NCs, which – together with alloyed CdₓHg₁₋ₓTe – are the only SC NCs that can be prepared in water in high quality without the need for an additional inorganic passivation shell. Aiming at a better understanding of the role of stabilizing ligands for the control of the application-relevant fluorescence features of SC NCs, we assessed the influence of two of the most commonly used monodentate thiol ligands, thioglycolic acid (TGA) and mercaptopropionic acid (MPA), on the colloidal stability, photoluminescence (PL) quantum yield (QY), and PL decay behavior of a set of CdTe NC colloids. As an indirect measure for the strength of the coordinative bond of the ligands to SC NC surface atoms, the influence of the pH (pD) and the concentration on the PL properties of these colloids was examined in water and D₂O and compared to the results from previous dilution studies with a set of thiol-capped Cd₁₋ₓHgₓTe SC NCs in D₂O. As a prerequisite for these studies, the number of surface ligands was determined photometrically at different steps of purification after SC NC synthesis with Ellman’s test. Our results demonstrate ligand control of the pH-dependent PL of these SC NCs, with MPA-stabilized CdTe NCs being less prone to luminescence quenching than TGA-capped ones. For both types of CdTe colloids, ligand desorption is more pronounced in H₂O compared to D₂O, underlining also the role of hydrogen bonding and solvent molecules. KW - Quantum dots KW - Fluorescence KW - Ligand analysis KW - Nano particles PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-371253 DO - https://doi.org/10.1039/c6cp03123d VL - 18 IS - 28 SP - 19083 EP - 19092 PB - RSC CY - Cambridge AN - OPUS4-37125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald A1 - Rogge, Andreas A1 - Thöns, S. A1 - Bismut, E. A1 - Straub, D. ED - Caspeele, Robby ED - Taerwe, Luc ED - Frangopol, Dan M. T1 - A sampling-based approach to identifying optimal inspection and repair strategies for offshore jacket structures N2 - Identifying optimal inspection and repair strategies for offshore jacket structures is a challenging task. We pre-sent an approach, which is based on recent developments in the field of risk-based operation and maintenance planning at the structural system level. The approach utilizes heuristics to define inspection and repair strate-gies at the system level and to reduce the search space of possible strategies. For each defined strategy, the expected service life cost of inspection, repair and failure is evaluated based on simulated inspection and re-pair histories. Subset simulation is applied to compute the conditional repair and failure probabilities required for this analysis. It also forms the basis for simulating inspection and repair histories. The strategy that mini-mizes the expected service life cost is the optimal one in the set of pre-selected strategies. The underlying condition and performance model accounts for the stochastic dependence among the deterioration states of the different structural elements and the structural redundancy. The approach is demonstrated in a case study considering a jacket-type frame. In this study, we essentially vary the inspection interval, the minimum num-ber of inspected components and the target reliability, and identify the combination that minimizes the ex-pected total service life cost. T2 - The sixth international symposium on life-cycle civil engineering (IALCCE 2018) CY - Ghent, Belgien DA - 28.10.2018 KW - Offshore steel structures KW - Fatigue KW - Reliability KW - Risk KW - Inspection planning PY - 2019 SN - 978-1-138-62633-1 SN - 978-1-315-22891-4 SP - 1081 EP - 1088 PB - Taylor & Francis Group CY - London AN - OPUS4-46434 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, I. A1 - Kebelmann, Katharina A1 - Risse, S. A1 - Dieguez-Alonso, A. A1 - Schartel, Bernhard A1 - Strecker, C. A1 - Behrendt, F. T1 - Hydroliquefaction of Two Kraft Lignins in a Semibatch Setup under Process Conditions Applicable for Large-Scale Biofuel Production N2 - Hydroliquefaction is a possible pathway to produce liquid transportation fuels from solid feedstocks like coal or biomass. Though much effort has been put into the investigation of maximizing the oil yield using expensive catalysts and pasting oils in batch setups, little is known about how to commercialize the process. This work aims at the demonstration of lignin hydroliquefaction under conditions interesting for commercial operation. The results from hydroliquefaction experiments of two different lignin types using a cheap iron-based catalyst and anthracene oil as the pasting oil in a semibatch system are presented here. Oil yields of above 50% are reached without observing coke formation. Extensive analyses of the feedstocks and product oils were performed. The process supplies high-quality oil, while differences in the decomposition path of both lignin types are observed. An high heating value of 39 400 J/g and H/C and O/C ratios of up to 1.6 and 0.1, respectively, are detected for the produced bio-oils. KW - Lignin KW - Hydroliquefaction KW - Biofuel PY - 2019 DO - https://doi.org/10.1021/acs.energyfuels.9b02572 SN - 0887-0624 SN - 1520-5029 VL - 33 IS - 11 SP - 11057 EP - 11066 PB - ACS AN - OPUS4-50102 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Duwe, M. A1 - Quast, J.-H. A1 - Schneider, S. A1 - Fischer, Daniel A1 - Beck, Uwe T1 - Thin-film metrology of tilted and curved surfaces by imaging Mueller-matrix ellipsometry N2 - For the vast majority of ellipsometric measurements, the application of planar substrates is mandatory and requires a proper sample alignment prior to the measurement. Here, the authors present a generalized approach of how to extract the isotropic ellipsometric sample parameters from an imaging Mueller-matrix measurement even if the sample is significantly misaligned. They validate the method by layer-thickness calculations based on imaging Mueller-matrix measurements of flat crystalline silicon samples that were misaligned on purpose. Furthermore, they also exploit this method’s capabilities to perform spatially resolved layer-thickness measurements of a single-layer indium-tin-oxide coating on a fused-silica microlens without the need of realignment or repositioning of the sample during the measurement. T2 - 8th International conference on spectroscopic ellipsometry (ICSE-8) CY - Barcelona, Spain DA - 26.05.2019 KW - Metrology KW - Thin films KW - Polarization spectroscopy KW - Spectroskopic Imaging KW - Mueller-Matrix imaging ellipsometry PY - 2019 DO - https://doi.org/10.1116/1.5122757 SN - 2166-2746 SN - 2327-9877 VL - 37 IS - 6 SP - 062908 PB - AIP CY - New York, NY AN - OPUS4-50209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Daniel A1 - Griepentrog, Michael A1 - Beck, Uwe A1 - Duwe, M. A1 - Quast, J.-H. A1 - Schneider, S. T1 - Effect of curvature of spherical microscopic indentations on the ellipsometric readout N2 - The authors describe and interpret curvature-related changes to the ellipsometric readout. As model system for a concave curvature, a set of three spherical microscopic indents in silicon (100) of different sizes was prepared by instrumented indentation testing using a spherical indenter. For reference, these samples were characterized by AFM to reveal the topography of each structure. The concavelike indents were analyzed by Mueller-Matrix imaging ellipsometry to extract lateral intensity images of 12 elements of the Mueller-Matrix. As a result of the detailed analysis of the image elements m22, m23, and m14, it was possible to correlate intensity changes and symmetry properties to depolarization and cross polarization induced by the edge threshold and the curved surface of the indent. KW - Spectroskopic Imaging KW - Mueller-Matrix imaging ellipsometry KW - Structural anomalies KW - Structural inhomogenities PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-498105 DO - https://doi.org/10.1116/1.5122252 VL - 37 IS - 6 SP - 062906-1 EP - 062906-5 PB - American Vacuum Society AN - OPUS4-49810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Guehrs, E. A1 - Schneider, M. A1 - Günther, Ch. M. A1 - Hessing, P. A1 - Heitz, K. A1 - Wittke, D. A1 - López-Serrano Oliver, Ana A1 - Jakubowski, Norbert A1 - Plendl, J. A1 - Eisebitt, S. A1 - Haase, A. T1 - Quantification of silver nanoparticle uptake and distribution within individual human macrophages by FIB/SEM slice and view N2 - Quantification of nanoparticle (NP) uptake in cells or tissues is very important for safety assessment. Often, electron microscopy based approaches are used for this purpose, which allow imaging at very high resolution. However, precise quantification of NP numbers in cells and tissues remains challenging. The aim of this study was to present a novel approach, that combines precise quantification of NPs in individual cells together with high resolution imaging of their intracellular distribution based on focused ion beam/ scanning electron microscopy (FIB/SEM) slice and view approaches. KW - Nanoparticles KW - FIB/SEM slice and view KW - Absolute dose KW - Cellular internalization KW - Macrophage PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-400626 DO - https://doi.org/10.1186/s12951-017-0255-8 SN - 1477-3155 VL - 15 SP - Article 21, 1 EP - 11 AN - OPUS4-40062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chapartegui-Arias, Ander A1 - Raysyan, A. A1 - Belenguer, A. M. A1 - Jaeger, Carsten A1 - Tchipilov, Teodor A1 - Prinz, Carsten A1 - Abad Andrade, Carlos Enrique A1 - Beyer, S. A1 - Schneider, Rudolf A1 - Emmerling, Franziska T1 - Tailored mobility in a zeolite imidazolate framework (ZIF) antibody conjugate N2 - Zeolitic imidazolate framework (ZIF) hybrid fluorescent nanoparticles and ZIF antibody conjugates have been synthesized, characterized, and employed in lateral-flow immunoassay (LFIA). The bright fluorescence of the conjugates and the possibility to tailor their mobility gives a huge potential for diagnostic assays. An enzyme-linked immunosorbent assay (ELISA) with horseradish peroxidase (HRP) as label, proved the integrity, stability, and dispersibility of the antibody conjugates, LC-MS/MS provided evidence that a covalent link was established between these metal-organic frameworks and lysine residues in IgG antibodies. KW - ZIF KW - ELISA PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-532096 DO - https://doi.org/10.1002/chem.202100803 SN - 0947-6539 SN - 1521-3765 VL - 27 IS - 36 SP - 9414 EP - 9421 PB - Wiley-VCH CY - Weinheim AN - OPUS4-53209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, S. A1 - Beck, T. A1 - Wittstock, B. A1 - Herbst, Tristan T1 - Sustainability assessment for the recycling of masonry N2 - In Germany, construction debris, road construction waste and excavated material amount to 60% of the total waste. The construction debris originates mainly from Building demolition and comprises of concrete and different types of masonry such as red brick, lime-sandstone, aerated concrete and lightweight concrete, but also other materials such as insulation material, gypsum, plaster, tiles, wood, Steel and plastics. Due to the large amount of building demolition material, the recycling of masonry to high-quality Recycling Products and closed-loop-recycling bears a high potential to reduce environmental impacts. Within the AiF (German Federation of Industrial Research Association) research Project “Sustainability Assessment for the Recycling of Masonry”, different recycling Technologies will be assessed with regard to their sustainability performance. All three pillars of sustainability - the ecological, the economic and the social pillar - will be considered, using the methods of Life Cycle Assessment (LCA), Life Cycle Costing (LCC) and Life Cycle Working Environment (LCWE). The assessment will be carried out for different Recycling technologies, for common ones but also for such technologies that are not yet in large scale application. The applicability of technologies depends on the type of the demolition material and on the purity of variety. One part of the research project is to develop a web-based tool for operators of recycling facilities and for demolition Companies to assess their recycling options. In most cases, demolished masonry has a very heterogeneous material composition, and therefore can only be used for lower-level recycling options or ends up in landfill. The aim of the project is to avoid landfilling and the downcycling of products and to achieve a higher recycling level. Closed-loop-recycling has priority. The main aspects of closed-loop-recycling are to change not the inherent properties of the recycled material and to recycle into the same or other product Systems. In the course of this, it is important to preserve the quality of the recycling material and to ensure a versatile use. To reach this target, different recycling technologies are identified and with the aid of the mentioned methods - LCA, LCC and LCWE - evaluated. In addition to predefined Processing routes, it is possible to assess individual recycling plants. A basic recyclingprinciple is defined to which further System modules can be added. The web-tool enables the user to identify different options - depending on the demolition material and its purity - and yields the sustainability assessment. Thus, the user gets Information about possibilities of the recycling of masonry and the environmental, economic and social Benefits compared to downcycling and landfill. T2 - SAM-6 - 6th International conference on society & materials CY - Leuven, Belgium DA - 30.05.2012 PY - 2012 SN - 1958-2897 SP - 1 EP - 7 AN - OPUS4-28644 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herbst, Tristan A1 - Beck, T. A1 - Schneider, S. A1 - Flassenberg, G. T1 - Nachhaltigkeitsanalyse für das Mauerwerksrecycling N2 - In Deutschland fällt mittelfristig eine nicht unerhebliche Menge an Mauerwerksbruch an. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind diese Restmassen zukünftig einem möglichst hochwertigen Recycling zuzuführen. Im Rahmen des IGF-Forschungsvorhabens 17022 N der Forschungsvereinigung Porenbetonindustrie e.V., Berlin, wird im Gesamtkontext “SIM Stoffkreislauf im Mauerwerksbau“ die Nachhaltigkeit verschiedener Recyclingoptionen für Mauerwerksbruch unter Einbeziehung der Hauptwandbausteinarten Ziegel, Kalksandstein, Porenbeton und Leichtbeton sowie unter Beachtung material- und verfahrenstechnischer sowie ökologischer, ökonomischer und sozialer Aspekte ganzheitlich untersucht und bewertet. Auf Grundlage der dabei gewonnenen Erkenntnisse wird ein rechnergestütztes Analysetool zur Nachhaltigkeitsbewertung für das Mauerwerksrecycling entwickelt. Auf diesem Wege sollen im Sinne der aktuellen gesetzlichen Vorgaben nachhaltige Stoffkreisläufe im Mauerwerksbau geschlossen und somit letztlich die Deponierung von Mauerwerksrestmassen vermieden werden.------------------------------------------------------------------------------------------------------------------------------------------------- In Germany, a not unimportant quantity of masonry rubble is generated in the medium term. With regard to a sustainable closed substance cycle waste management, these rest masses have to be recycled if possible. Within the IGF research project “Sustainability Analysis for the Recycling of Masonry”, different recycling options will be assessed with regard to their sustainability performance. In doing so, the main kinds of masonry units (clay units, calcium silicate units, autoclaved aerated concrete units, aggregate concrete units), their material properties, the processing technologies as well as ecological, economic and social aspects will be considered. Based on the results, a web-based tool will be developed to assess the sustainability of different recycling options for masonry rubble. PY - 2012 DO - https://doi.org/10.1002/dama.201200549 SN - 1432-3427 SN - 1437-1022 VL - 16 IS - 5 SP - 242 EP - 246 PB - Ernst CY - Berlin AN - OPUS4-27392 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Oberleitner, Lidia A1 - Eremin, S.A. A1 - Lehmann, Andreas A1 - Garbe, L.-A. A1 - Schneider, Rudolf T1 - Fluorescence polarization immunoassays for carbamazepine - comparison of tracers and formats N2 - For the antiepileptic drug and anthropogenic marker carbamazepine (CBZ), a fast and cost-effective immunoassay based on fluorescence polarization (FPIA) was developed. The required fluorophore conjugates were synthesized from different fluorescein and CBZ derivatives. The most suitable tracer was CBZ–triglycine–5-(aminoacetamido)fluorescein. Additionally, the applicability of the assay in tubes and on microtiter plates was tested. The first format can be performed in a portable instrument and therefore can be applied in field measurements. The measurement of an individual sample can be carried out within 4 min. This assay shows a measurement range of 2.5–1000 µg L-1 and a test midpoint (or IC50) of 36 µg L-1. The FPIA performed on microtiter plates is useful for the assay development and is suitable for a very high throughput (up to 24 samples in 20 min). The test midpoint of this assay is 13 µg L-1 and the measurement range is 1.5–300 µg L-1. Furthermore, this assay requires smaller sample volumes and less reagents, including the crucial amount of antibody. The applicability of both assays to spiked surface water samples was evaluated. The recovery rates vary between 66–110% on microtiter plates and 81–140% in tubes. PY - 2015 DO - https://doi.org/10.1039/c5ay00617a SN - 1759-9660 SN - 1759-9679 VL - 7 IS - 14 SP - 5854 EP - 5861 PB - RSC Publ. CY - Cambridge AN - OPUS4-33821 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wang, L. A1 - Stebbings, R. A1 - Gaigalas, A.K. A1 - Sutherland, J. A1 - Kammel, M. A1 - John, M. A1 - Roemer, B. A1 - Kuhne, Maren A1 - Schneider, Rudolf A1 - Braun, M. A1 - Engel, A. A1 - Dikshit, D. A1 - Abbasi, F. A1 - Marti, G.E. A1 - Sassi, M. A1 - Revel, L. A1 - Kim, S.K. A1 - Baradez, M.-O. A1 - Lekishvili, T. A1 - Marshall, D. A1 - Whitby, L. A1 - Jing, W. A1 - Ost, V. A1 - Vonsky, M. A1 - Neukammer, J. T1 - Quantification of cells with specific phenotypes II: Determination of CD4 expression level on reconstituted lyophilized human PBMC labelled with anti-CD4 FITC antibody N2 - This report focuses on the characterization of CD4 expression level in terms of equivalent number of reference fluorophores (ERF). Twelve different flow cytometer platforms across sixteen laboratories were utilized in this study. As a first step the participants were asked to calibrate the fluorescein isothiocyanate (FITC) channel of each flow cytometer using commercially available calibration standard consisting of five populations of microspheres. Each population had an assigned value of equivalent fluorescein fluorophores (EFF denotes a special case of the generic term ERF with FITC as the reference fluorophore). The EFF values were assigned at the National Institute of Standards and Technology (NIST). A surface-labelled lyophilized cell preparation was provided by the National Institute of Biological Standards and Control (NIBSC), using human peripheral blood mononuclear cells (PBMC) pre-labeled with a FITC conjugated anti-CD4 monoclonal antibody. Three PBMC sample vials, provided to each participant, were used for the CD4 expression analysis. The PBMC are purported to have a fixed number of surface CD4 receptors. On the basis of the microsphere calibration, the EFF value of the PBMC samples was measured to characterize the population average CD4 expression level of the PBMC preparations. Both the results of data analysis performed by each participant and the results of centralized analysis of all participants' raw data are reported. Centralized analysis gave a mean EFF value of 22,300 and an uncertainty of 750, corresponding to 3.3% (level of confidence 68%) of the mean EFF value. The next step will entail the measurement of the ERF values of the lyophilized PBMC stained with labels for other fluorescence channels. The ultimate goal is to show that lyophilized PBMC is a suitable biological reference cell material for multicolor flow cytometry and that it can be used to present multicolor flow cytometry measurements in terms of ABC (antibodies bound per cell) units. KW - Surface labelled lyophilized PBMC KW - CD4 expression level KW - FITC KW - Equivalent fluorescein fluorophore (EFF) KW - Quantitative flow cytometry KW - Calibration KW - Standard measurement procedure KW - Measurement uncertainty KW - Reference cell material PY - 2015 DO - https://doi.org/10.1002/cyto.a.22634 SN - 0196-4763 SN - 1552-4922 SN - 1552-4930 VL - 87 IS - 3 SP - 254 EP - 261 PB - Wiley-Liss CY - Hoboken, NJ AN - OPUS4-32981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stebbings, R. A1 - Wang, L. A1 - Sutherland, J. A1 - Kammel, M. A1 - Gaigalas, A.K. A1 - John, M. A1 - Roemer, B. A1 - Kuhne, Maren A1 - Schneider, Rudolf A1 - Braun, M. A1 - Engel, A. A1 - Dikshit, D.K. A1 - Abbasi, F. A1 - Marti, G.E. A1 - Sassi, M.P. A1 - Revel, L. A1 - Kim, S.-K. A1 - Baradez, M.-O. A1 - Lekishvili, T. A1 - Marshall, D. A1 - Whitby, L. A1 - Jing, W. A1 - Ost, V. A1 - Vonsky, M. A1 - Neukammer, J. T1 - Quantification of cells with specific phenotypes I: Determination of CD4+ cell count per microliter in reconstituted lyophilized human PBMC prelabeled with anti-CD4 FICT antibody N2 - A surface-labeled lyophilized lymphocyte (sLL) preparation has been developed using human peripheral blood mononuclear cells prelabeled with a fluorescein isothiocyanate conjugated anti-CD4 monoclonal antibody. The sLL preparation is intended to be used as a reference material for CD4+ cell counting including the development of higher order reference measurement procedures and has been evaluated in the pilot study CCQM-P102. This study was conducted across 16 laboratories from eight countries to assess the ability of participants to quantify the CD4+ cell count of this reference material and to document cross-laboratory variability plus associated measurement uncertainties. Twelve different flow cytometer platforms were evaluated using a standard protocol that included calibration beads used to obtain quantitative measurements of CD4+ T cell counts. There was good overall cross-platform and counting method agreement with a grand mean of the laboratory calculated means of (301.7 ± 4.9) µL-1 CD4+ cells. Excluding outliers, greater than 90% of participant data agreed within ±15%. A major contribution to variation of sLL CD4+ cell counts was tube to tube variation of the calibration beads, amounting to an uncertainty of 3.6%. Variation due to preparative steps equated to an uncertainty of 2.6%. There was no reduction in variability when data files were centrally reanalyzed. Remaining variation was attributed to instrument specific differences. CD4+ cell counts obtained in CCQM-P102 are in excellent agreement and show the robustness of both the measurements and the data analysis and hence the suitability of sLL as a reference material for interlaboratory comparisons and external quality assessment. KW - CD4+ cell counting KW - Relative concentration measurement KW - Lyophilized cells KW - Flow cytometry KW - Standard measurement procedure KW - Measurement of uncertainty KW - Human immunodeficiency virus-1 KW - Acquired immunodeficiency syndrome KW - Reference material PY - 2015 DO - https://doi.org/10.1002/cyto.a.22614 SN - 0196-4763 SN - 1552-4922 SN - 1552-4930 VL - 87 IS - 3 SP - 244 EP - 253 PB - Wiley-Liss CY - Hoboken, NJ AN - OPUS4-32847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Filipe, O.M.S. A1 - Vidal, M.M. A1 - Scherer, H.W. A1 - Schneider, Rudolf A1 - Duarte, A. A1 - Esteves, V.I. A1 - Santos, E.B.H. T1 - Effect of long term organic amendments on adsorption-desorption of thiram onto a luvisol soil derived from loess KW - Thiram KW - Adsorption-desorption KW - Soil KW - Organic amendments PY - 2010 DO - https://doi.org/10.1016/j.chemosphere.2010.04.003 SN - 0045-6535 SN - 0366-7111 VL - 80 IS - 3 SP - 293 EP - 300 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-23196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lima, D. A1 - Santos, S A1 - Scherer, H. A1 - Schneider, Rudolf A1 - Duarte, A. A1 - Santos, E. A1 - Esteves, V. T1 - Effects of organic and inorganic amendments on soil organic matter properties N2 - The aim of this work was to investigate the effects of long-term application of different organic fertilizers (sewage sludge, farmyard manure, compost) as compared to mineral fertilizer on the structure of the soil organic matter. Capillary electrophoresis was employed for the quantification of monosaccharides and phenolic compounds, whereas NMR and FT-IR were used for the overall characterization of the soils organic matter. Application of farmyard manure results in a higher content of organic matter derived from angiosperms, suggested by the higher levels of syringic and vanillic phenols. Spectroscopic studies show an increase of lignin and lignin-like products in the organic matter of the soil, which may be derived from the cereal straw supplied with farmyard manure. According to spectroscopic analysis, 13C CPMAS-NMR and FT-IR spectra, higher contents of methylene groups (– CH2) from proteins and protein-like compounds, as well as higher levels of carbohydrates, were found in the soil supplied with compost. The monosaccharide (rhamnose, xylose, glucose, mannose, arabinose, fucose and galactose) content was not significantly influenced by the different organic fertilizers, suggesting that the type of amendment used does not affect any of these six studied monomers. Comparing the three organic amendments the most significant differences were observed after long-term application of farmyard manure, with an increase in lignin and lignin-like products in the soil organic matter, and compost, which appears to contribute to an increase of protein and protein-like, as well as carbohydrates content on soil organic matter. The knowledge of such changes can be essential to understand the sorption and bioavailability of pollutants, as well as establish/unestablish ways to recycling organic residues as organic fertilizers. KW - Soil amendment KW - Organic matter charcterization KW - Phenols KW - Monosaccharide KW - CZE KW - FT-IR KW - 13C-NMR PY - 2009 DO - https://doi.org/10.1016/j.geoderma.2009.01.009 SN - 0016-7061 SN - 1872-6259 VL - 150 IS - 1-2 SP - 38 EP - 45 PB - Elsevier CY - Amsterdam AN - OPUS4-19333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martínez, N.A. A1 - Pereira, S.V. A1 - Bertolino, F.A. A1 - Schneider, Rudolf A1 - Messina, G.A. A1 - Raba, J. T1 - Electrochemical detection of a powerful estrogenic endocrine disruptor: ethylestradiol in water samples through bioseparation procedure N2 - The synthetic estrogen ethinylestradiol (EE2) is an active component of oral contraceptives (OCs), considered as an endocrine disrupting compound (EDC). It is excreted from humans and released via sewage treatment plant effluents into aquatic environments. EDCs are any environmental pollutant chemical that, once incorporated into an organism, affects the hormonal balance of various species including humans. Its presence in the environment is becoming of great importance in water quality. This paper describes the development of an accurate, sensitive and selective method for capture, preconcentration and determination of EE2 present in water samples using: magnetic particles (MPs) as bioaffinity support for the capture and preconcentration of EE2 and a glassy carbon electrode modified with multi-walled carbon nanotubes (MWCNTs/GCE) as detection system. The capture procedure was based on the principle of immunoaffinity, the EE2 being extracted from the sample using the anti-EE2 antibodies (anti-EE2 Ab) which were previously immobilized on MPs. Subsequently the analyte desorption was done employing a sulfuric acid solution and the determination of the EE2 in the pre-concentrated solution was carried out by square wave voltammetry (SWV). This method can be used to determine EE2 in the range of 0.035–70 ng L-1 with a detection limit (LOD) of 0.01 ng L-1 and R.S.D. < 4.20%. The proposed method has been successfully applied to the determination of EE2 in water samples and it has promising analytical applications for the direct determination of EE2 at trace levels. KW - Magnetic particles KW - Bioseparation KW - Ethinylestradiol KW - Electrochemistry KW - Immunoassay KW - Elektrochemischer Sensor KW - Endokrine Disruptoren KW - Hormone KW - EE2 KW - Östrogene PY - 2012 DO - https://doi.org/10.1016/j.aca.2012.02.033 SN - 0003-2670 SN - 1873-4324 SN - 0378-4304 VL - 723 SP - 27 EP - 32 PB - Elsevier CY - Amsterdam AN - OPUS4-25656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -