TY - JOUR A1 - Buge, Hans-Gerhard A1 - Becker, Roland A1 - Scharf, Holger T1 - 11. BAM-Ringversuch "Altlasten" PY - 2005 SN - 0942-5675 VL - 49 IS - 7-8 SP - TT 10 PB - Vereinigte Fachverl. CY - Mainz AN - OPUS4-10381 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharf, Holger A1 - Becker, Roland A1 - Bremser, Wolfram A1 - Buge, Hans-Gerhard A1 - Lück, Detlef T1 - Certification of the mass fractions of trace elements and pentachlorophenol in an impregnated wood reference material N2 - The resource-saving utilisation of recovered waste wood is a matter of growing concern. In several European countries, this utilisation is governed by regulations and is dependent on the contents of certain trace elements and organic compounds. Thus, for decisionmaking with respect to waste wood management (recycling or combustion), reliable analytical data are needed and, due to their great economic and environmental impact, must be assured by appropriate quality control. To support the improvement in quality assurance in waste wood analysis, for the first time, a wood reference material was certified for its mass fractions of arsenic, cadmium, chromium, copper, lead, mercury, and pentachlorophenol (PCP). These analytes were selected because they represent typical constituents of wood preservatives most widely used in the past. Material preparation and testing of homogeneity and stability were carried out by BAM Federal Institute for Materials Research and Testing. The certification measurements were performed involving selected laboratories with documented expertise in the field of waste wood analysis. The certified values and their corresponding uncertainties were assigned in full compliance with the requirements of ISO Guide 35. The certified mass fractions and their expanded uncertainties (k/i> = 2) are as follows: (3.1 ± 0.5) mg/kg for As, (3.02 ± 0.24) mg/kg for Cd, (36.4 ± 2.6) mg/kg for Cr, (22.9 ± 1.7) mg/kg for Cu, (0.60 ± 0.14) mg/kg for Hg, (39 ± 4) mg/kg for Pb, and (7.9 ± 0.6) mg/kg for PCP. The certified material is available as European Reference Material ERM®-CD100. KW - Waste wood KW - Trace elements KW - Pentachlorophenol KW - Certification KW - European reference material PY - 2010 U6 - https://doi.org/10.1007/s00769-010-0699-0 SN - 0949-1775 SN - 1432-0517 VL - 15 IS - 11 SP - 613 EP - 619 PB - Springer CY - Berlin AN - OPUS4-22392 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krysell, M. A1 - Becker, Roland A1 - Wegener, J. W. A1 - Buge, Hans-Gerhard T1 - Certified reference materials for organic contaminants in sewage sludge - a feasibility study N2 - As an answer to the re-evaluation of the European sludge directive, two novel reference materials for organic components in municipal sludge have been produced and test certified for AOX (absorbable organic halogens), PAH (polycyclic aromatic hydrocarbons), NPE (nonylphenol and nonylphenolethoxylates), DEHP (di(2-ethylhexyl)phthalate), bisphenol A, and BFR (brominated flame retardants). The materials were prepared from raw sludge without spiking or mixing of different sludges. The study demonstrated that the technique for the preparation of a suitable reference material, sufficiently homogenous and stable, and with concentration levels that answer the needs of the laboratories and the relevant authorities, can now be presented in detail. The results, furthermore, show there is a need for method validation and standardisation of the measurements of NPEs and certain BFR congeners, and that the development of the laboratory structure in Europe, with fewer and more specialised laboratories, might become a major obstacle when trying to find a sufficient number of laboratories being appropriately proficient for this kind of study in the future. KW - Organic pollutants KW - Municipal sludge KW - CRM KW - AOX KW - BPA KW - PAH KW - DEHP KW - NPE KW - BFR PY - 2008 U6 - https://doi.org/10.1007/s00769-008-0431-5 SN - 0949-1775 SN - 1432-0517 VL - 13 IS - 10 SP - 553 EP - 562 PB - Springer CY - Berlin AN - OPUS4-18362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Buge, Hans-Gerhard A1 - Win, Tin T1 - Determination of pentachlorphenol (PCP) in waste wood - method comparison by a collaborative trial N2 - Two independently developed and validated procedures for the determination of pentachlorophenol (PCP) in waste wood were compared by means of a collaborative trial. Both methods foresee quantification of PCP by gas chromatography (GC-ECD) after acetylation and differ with regard to the use of methanol or toluene/sulphuric acid, respectively, as solvent in the sonication extraction step. Test samples with established analyte homogeneity were prepared from a ground “real life” starting material. A total of 23 participating laboratories with experience in wood preservative analysis were instructed to apply both methods to three levels of content in the range of 0.5–20 mg PCP/kg. In case of the toluene/sulphuric acid extraction, lower recoveries and higher interlaboratory dispersion of results at the higher PCP contents were observed. Seen against the background of the Horwitz equation a reproducibility standard deviation of not, vert, similar19% for the methanol extraction at the 4.5 mg/kg level meets the requirement for a sound analytical method. Thus, the sonication extraction procedure with methanol has been annexed as a reference method to the German waste wood regulation. KW - Extraction KW - Derivatisation KW - Sonication KW - Analysis KW - Gas chromatography KW - Regulation PY - 2002 U6 - https://doi.org/10.1016/S0045-6535(02)00004-8 SN - 0045-6535 SN - 0366-7111 VL - 47 SP - 1001 EP - 1006 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-1628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Buge, Hans-Gerhard A1 - Becker, Roland A1 - Scharf, Holger A1 - Walther, Wolfgang A1 - Sauer, Andreas T1 - Die Altlastenringversuche der BAM - Ein anerkanntes Instrument zur Kompetenzbewertung von Prüflaboratorien KW - Ringversuch KW - Referenzmaterialien KW - Umweltanalytik KW - Boden KW - Abfall KW - Qualitätsmanagement KW - Kompetenzbewertung KW - Akkreditierung PY - 2006 SN - 0942-5675 N1 - Geburtsname von Sauer, Andreas: Buchholz, A. - Birth name of Sauer, Andreas: Buchholz, A. VL - 50 IS - 5 SP - TT20 EP - TT23 PB - Vereinigte Fachverl. CY - Mainz AN - OPUS4-12396 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koch, Matthias A1 - Buge, Hans-Gerhard A1 - Becker, Roland A1 - Nehls, Irene T1 - Kalibrierstandard für die Mineralöl (MKW)-analytik mittels GC-FID KW - Kalibrierstand KW - Referenzmaterial KW - MKW KW - GC PY - 2005 SN - 0016-3538 VL - 49 IS - 11 SP - 207 PB - GIT-Verlag CY - Darmstadt AN - OPUS4-11601 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Buge, Hans-Gerhard A1 - Bremser, Wolfram A1 - Nehls, Irene T1 - Mineral oil content in sediments and soils: comparability, traceability and a certified reference material for quality assurance N2 - The performance of twelve laboratories with previously established proficiency in the determination of the mineral oil content in a fresh water sediment is described. The summation parameter total petrol hydrocarbon (TPH) is defined according to ISO 16703:2004 with regard to the sample preparation to be applied, the flame ionisation detection (FID) and the boiling range of C10–C40 to be integrated. Comprehensive tests of homogeneity and stability have been carried out on the candidate material using appropriate models. The outcome of the study served as the basis for the certification of the candidate reference material as ERM-CC015a. The certified mass fraction is 1,820±130mgkg-1 and traceability was established by using an appropriate calibration standard certified for the mass fraction of C10–C40. The interlaboratory scatter of measurement results in this exercise can largely be explained by the variability of the individual calibrations based on this common calibration standard. KW - Total petroleum hydrocarbons KW - Extraction KW - Gas chromatography KW - Calibration KW - Interlaboratory study PY - 2006 U6 - https://doi.org/10.1007/s00216-006-0423-4 SN - 1618-2642 SN - 1618-2650 VL - 385 IS - 3 SP - 645 EP - 651 PB - Springer CY - Berlin AN - OPUS4-12399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehls, Irene A1 - Becker, Roland A1 - Buge, Hans-Gerhard T1 - Pentachlorphenol - Eine Altlast im Holz PY - 2005 UR - http://archiv.aktuelle-wochenschau.de/2005/woche19/woche19.html IS - 19 SP - 1 EP - 2 PB - Gesellschaft Deutscher Chemiker CY - Frankfurt am Main AN - OPUS4-10845 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Walther, Wolfgang A1 - Becker, Roland A1 - Nehls, Irene A1 - Lehmann, Andreas A1 - Redlich, Christel A1 - Flemig, Sabine A1 - Dorgerloh, Ute A1 - Win, Tin A1 - Buge, Hans-Gerhard T1 - Pentchlorophenol (PCP) in Soil - Certified Reference Materials for Environmental Analysis T2 - Analytica Conference 2002 CY - Munich, Germany DA - 2002-04-23 PY - 2002 SP - 1(?) AN - OPUS4-1389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Nehls, Irene A1 - Buge, Hans-Gerhard T1 - Referenzmaterialien für Umweltanalysen PY - 2001 SN - 0016-3538 IS - 45 SP - 1089 EP - 1091 PB - GIT-Verlag CY - Darmstadt AN - OPUS4-1186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf, Holger A1 - Becker, Roland A1 - Buge, Hans-Gerhard T1 - Soil Analysis - The BAM Proficiency Testing Scheme "Contaminated Sites" T2 - International ILAC/IAF Conference on Accreditation in Global Trade CY - Berlin, Germany DA - 2002-09-23 KW - Böden KW - Eignungsprüfung KW - Qualitätssicherung KW - Ringversuche KW - Umweltanalytik PY - 2002 AN - OPUS4-2361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Buge, Hans-Gerhard A1 - Scharf, Holger A1 - Becker, Roland ED - Gills, T. T1 - Soil samples prepared for a proficiency testing scheme operated by BAM T2 - 8th International Symposium on Biological and Environmental Reference Materials ; 8th BERM CY - Bethesda, MD, USA DA - 2000-09-17 PY - 2001 SN - 1618-2642 VL - 370 IS - 2-3 SP - 174 PB - Springer CY - Berlin AN - OPUS4-944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Buge, Hans-Gerhard A1 - Nehls, Irene T1 - The determination of adsorbable organically bound halogens (AOX) in soil: interlaboratory comparisons and reference materials N2 - The interlaboratory variability in the quantification of adsorbable organically bound halogens (AOX) in industrially contaminated soil is presented. Three consecutive rounds of a proficiency testing scheme, in which between 88 and 119 routine laboratories participated, yielded relative reproducibility standard deviations between 7 and 20% at AOX contents between 10.9 and 268 mg kg-1. Nineteen laboratories with established proficiency were invited to participate in the certification of the AOX content in three soil reference materials meant for the internal quality control in analytical laboratories. The certified values are (1349 ± 59) mg kg-1, (80 ± 7) mg kg-1 and (102 ± 8) mg kg-1, respectively. KW - Certified reference materials KW - European Reference Material KW - Proficiency testing KW - Organohalogen compounds KW - Summation parameter PY - 2007 U6 - https://doi.org/10.1007/s00769-007-0308-z SN - 0949-1775 SN - 1432-0517 VL - 12 IS - 12 SP - 647 EP - 651 PB - Springer CY - Berlin AN - OPUS4-16670 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Buge, Hans-Gerhard A1 - Becker, Roland A1 - Nehls, Irene T1 - The preparation and characterization of solid matrix reference materials for the trace analysis of organic environmental pollutants - relevant aspects of quality management N2 - Feste Referenzmaterialien für die Spurenanalytik umweltrelevanter organischer Schadstoffe erfordern aufgrund der geringen thermischen Belastbarkeit der Analyten besondere Aufarbeitungsstrategien für die Herstellung repräsentativer Teilproben. Das in der Fachgruppe I.2 seit 1994 für diesen Zweck systematisch aufgebaute technologische Instrumentarium wird vorgestellt, und das im Laufe der Jahre angesammelte Know How wird anhand von Beispielen vermittelt. Das im Laboratorium I.21 entwickelte Qualitätssystem für eine optimale Logistik der Arbeitsabläufe der Probenherstellung und -verwaltung sowie für eine bedarfsgerechte Charakterisierung der Materialien wird ausführlich erläutert. Bezüglich der Verwendung der Referenzmaterialien wird herausgestellt, daß es zwei gleichberechtigte Anwendungsrichtungen gibt: die interne Qualitätskontrolle mit zertifizierten Referenzmaterialien (ZRM, z.B. für die Methodenvalidierung) und die externe Qualitätskontrolle (Proficiency Testing = Kompetenzbewertung von Prüflaboratorien). Referenzmaterialien für das Proficiency Testing, die im Umweltbereich in viel größeren Stückzahlen umgesetzt werden können als ZRM, weisen bezüglich Homogenität und Charakterisierung die gleichen Qualitätskriterien wie ZRM auf. Diese Materialien haben - auch im internationalen Maßstab - stark an Bedeutung gewonnen. Ein englisches Abstract gibt es nicht, aber eine Grobgliederung zur Vortragsankündigung: This lecture includes: · the technological and logistical aspects of reference material preparation and sub-sampling and subsequent sample management, · appropriate measurement strategies for homogeneity and stability studies, · the use of relevant statistical tests to evaluate those measurement data, · the organisation of interlaboratory studies based on traceable measurements T2 - CENAM CY - Querétaro, Mexico DA - 2002-03-01 PY - 2002 AN - OPUS4-1612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -