TY - JOUR A1 - Thiodjio Sendja, Bridinette A1 - Tchouank Tekou, Carol Trudel A1 - Prinz, Carsten A1 - de Oliveira Guilherme Buzanich, Ana T1 - Adsorptive performance of single-walled carbon nanotubes for divalent manganese sorption characterized by X-ray absorption spectroscopy N2 - The adsorptive performance of divalent manganese onto single-walled carbon nanotubes (SWCNTs) is investigated by X-ray absorption spectroscopy (XAS). The study is focused on the one hand, on the use of SWCNT as adsorbent to remove divalent manganese II) pollutant controlling batch parameters such as pH, adsorbent dose and contact time; and on the other hand, on the characterization of manganese adsorbed by SWCNT (Mn-SWCNT) adsorbent to probe the chemical composition, oxidation state, and local structural environment of Mn absorber. Freundlich adsorption isotherm well fitted the experimental data and suggested the maximum adsorption capacity at pH 2. Ion exchange was proposed as the main adsorption mechanism for removing manganese using SWCNT. XAS results revealed the change in the oxidation state of manganese. The effect of pH, adsorbent dose, and contact time is shown. XAS also showed that Mn-SWCNT material is principally composed of MnCl2, Mn2O3, MnO2, Mn3O4, and MnO in decreasing order with MnCl2 and Mn2O3 as major compounds. KW - Local environment KW - Single-walled carbon nanotubes KW - Divalent manganese KW - Adsorptive performance KW - X-ray absorption spectroscopy KW - Oxidation state PY - 2025 DO - https://doi.org/10.1007/s11696-025-04418-5 SN - 0366-6352 SP - 1 EP - 15 PB - Springer Science and Business Media LLC AN - OPUS4-64492 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Andresen, Elina A1 - Resch-Genger, Ute A1 - Michaelis, Matthias A1 - Prinz, Carsten A1 - Würth, Christian T1 - Time-resolved luminescence spectroscopy for monitoring the stability and dissolution behaviour of upconverting nanocrystals with different surface coatings† N2 - We demonstrate the potential of time-resolved luminescence spectroscopy for the straightforward assessment and in situ monitoring of the stability of upconversion nanocrystals (UCNPs). Therefore, we prepared hexagonal NaYF4:Yb3+,Er3+ UCNPs with various coatings with a focus on phosphonate ligands of different valency, using different ligand exchange procedures, and studied their dissolution behaviour in phosphate-buffered saline (PBS) dispersions at 20 °C and 37 °C with various analytical methods. The amount of the released UCNPs constituting fluoride ions was quantified by potentiometry using a Fluoride ion-sensitive electrode and particle disintegration was confirmed by transmission electron microscopy studies of the differently aged UCNPs. In parallel, the luminescence features of the UCNPs were measured with special emphasis on the lifetime of the sensitizer emission to demonstrate its suitability as Screening parameter for UCNP stability and changes in particle composition. The excellent correlation between the changes in luminescence lifetime and fluoride concentration highlights the potential of our luminescence lifetime method for UCNP stability screening and thereby indirect monitoring of the release of potentially hazardous fluoride ions during uptake and dissolution in biological systems. Additionally, the developed in situ optical method was used to distinguish the dissolution dynamics of differently sized and differently coated UCNPs. KW - Fluorescence KW - Lifetime KW - Method KW - Quantification KW - Stability KW - Coating KW - Surface chemistry KW - Lanthanide KW - Fluoride KW - Electrochemistry KW - ICP-OES KW - Upconversion KW - Nano KW - Particle KW - Aging KW - Quality assurance KW - TEM PY - 2020 DO - https://doi.org/10.1039/d0nr02931a VL - 12 IS - 23 SP - 12589 EP - 12601 PB - Royal Society od Chemistry AN - OPUS4-52088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Villajos Collado, José Antonio A1 - Zimathies, Annett A1 - Prinz, Carsten T1 - A fast procedure for the estimation of the hydrogen storage capacity by cryoadsorption of metalorganic framework materials from their available porous properties N2 - In order to identify the best porous materials for the cryogenic physisorption of hydrogen, high-throughput calculations are performed starting, i.e., from the collected information in crystallographic databases. However, these calculations, like molecular simulations, require specific training and significant computational cost. Herein, a relatively simple procedure is proposed to estimate and compare hydrogen uptakes at 77 K and pressure values from 40 bar starting from the porous properties of MOF materials, without involving simulation tools. This procedure uses definitions for adsorption and considers the adsorbed phase as an incompressible fluid whose pressure-density change is that for the liquid phase at 19 K. For the 7000 structures from the CoRE MOF database, the average error of the predictions is only of 1% from reference values at 100 bar, with an SD of ±8%. This accuracy is lower than that from simulation tools, but involving lower computational cost and training. KW - Metal-organic frameworks KW - MOF databases KW - Hydrogen cryostorage KW - Supercritical adsorption KW - Absolute adsorption KW - Uptake estimation PY - 2021 DO - https://doi.org/10.1016/j.ijhydene.2020.10.265 SN - 0360-3199 VL - 46 SP - 29323 EP - 29331 PB - Elsevier CY - Oxford AN - OPUS4-53133 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Drzymala, Sarah A1 - Weiz, S. A1 - Heinze, J. A1 - Marten, S. A1 - Prinz, Carsten A1 - Zimathies, Annett A1 - Garbe, L.-A. A1 - Koch, Matthias T1 - Automated solid-phase extraction coupled online with HPLC-FLD for the quantification of zearalenone in edible oil N2 - Established maximum levels for the mycotoxin zearalenone (ZEN) in edible oil require monitoring by reliable analytical methods. Therefore, an automated SPE-HPLC online system based on dynamic covalent hydrazine chemistry has been developed. The SPE step comprises a reversible hydrazone formation by ZEN and a hydrazine moiety covalently attached to a solid phase. Seven hydrazine materials with different properties regarding the resin backbone, pore size, particle size, specific surface area, and loading have been evaluated. As a result, a hydrazine-functionalized silica gel was chosen. The final automated online method was validated and applied to the analysis of three maize germ oil samples including a provisionally certified reference material. Important performance criteria for the recovery (70–120 %) and precision (RSDr <25 %) as set by the Commission Regulation EC 401/2006 were fulfilled: The mean recovery was 78 % and RSDr did not exceed 8 %. The results of the SPE-HPLC online method were further compared to results obtained by liquid&–liquid extraction with stable isotope dilution analysis LC-MS/MS and found to be in good agreement. The developed SPE-HPLC online system with fluorescence detection allows a reliable, accurate, and sensitive quantification (limit of quantification, 30 µg/kg) of ZEN in edible oils while significantly reducing the workload. To our knowledge, this is the first report on an automated SPE-HPLC method based on a covalent SPE approach. KW - Dynamic covalent hydrazine chemistry (DCHC) KW - Maize germ oil KW - Food KW - Mycotoxin KW - ZEA KW - Isomerisation KW - Occurrence KW - Edible oil KW - SIDA KW - LC-MS/MS KW - Quantification PY - 2015 DO - https://doi.org/10.1007/s00216-015-8541-5 SN - 1618-2642 SN - 1618-2650 VL - 407 IS - 12 SP - 3489 EP - 3497 PB - Springer CY - Berlin AN - OPUS4-33067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adolphs, Jürgen A1 - Rübner, Katrin A1 - Schnell, A. A1 - Prinz, Carsten A1 - Peplinski, Burkhard A1 - Hempel, S. ED - Ludwig, H.-M. T1 - Porenstruktur hydrothermal erhärteter Granulate aus Mauerwerkbruch N2 - Die Herstellung hydrothermal erhärteter Granulate ist eine Möglichkeit zur Wiederverwertung von ziegelhaltigem Mauerwerkbruch, der derzeit aufgrund der heterogenen Zusammensetzung und hoher Feinanteile ein besonders hohes Verwertungsdefizit aufweist. Dabei ist die hydrothermale Erhärtung in einem Autoklav bei 200 °C und 1.6 MPa in gesättigter Wasserdampfatmosphäre eine Alternative mit geringerem Energieverbrauch im Vergleich zur thermischen Herstellung von Leichtgranulaten aus mineralischen Abfällen (Blähgranulate) oder Tonen und Schiefer (kommerzieller Blähton bzw. Blähschiefer), die bei Temperaturen von 1200-1300 °C im Drehrohrofen erfolgt. Die Festigkeit der Hydrothermalgranulate entwickelt sich bei diesem Prozess durch die Ausbildung von Calciumsilicathydrat-Phasen (CSH), die durch die Reaktion zwischen Quarzpartikeln und hydratisiertem Kalk entstehen. Die so erzeugten Hydrothermalgranulate haben Rohdichten zwischen 1500 kg/m3 und 2000 kg/m3. Damit und auch durch andere Eigenschaften unterscheiden sie sich von den thermisch erhärteten Blähgranulaten bzw. Blähtonen. Ursache dafür ist letztendlich eine sehr unterschiedliche Gefüge- und Porenstruktur. Im vorliegenden Beitrag wird hauptsächlich über die Ergebnisse der Mikrostrukturuntersuchungen an Hydrothermalgranulaten zusammen mit ihren technologischen Eigenschaften, wie Kornfestigkeit, Rohdichte und Wasseraufnahme, berichtet. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Leichtgranulat KW - Mauerwerkbruch KW - Hydrothermale Herstellung KW - Mikrostruktur KW - Porenstruktur PY - 2015 SN - 978-3-00-050225-5 VL - 2 SP - 2-291 EP - 2-298 AN - OPUS4-34878 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Redda, Zinnabu T. A1 - Brennecke, Daniel A1 - Prinz, Carsten A1 - Yimam, Abubeker A1 - Barz, Mirko A1 - Kadow, Stefen A1 - Laß-Seyoum, Asnakech T1 - Correction to: Synthesis and characterization of AlPO4-18 supported mesoporous and crystalline β-Mo2C, Ni3C, and WC nanoparticles N2 - This is a corrigendum to the original article "Synthesis and characterization of AlPO4-18 supported mesoporous and crystalline β-Mo2C, Ni3C, and WC nanoparticles" that was published in the journal "Catalysis letters", vol. 154 (2024), pp. 5969-5988. PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626139 DO - https://doi.org/10.1007/s10562-024-04896-4 SN - 1011-372X SN - 1572-879X VL - 155 SP - 1 PB - Springer Science and Business Media CY - Dordrecht AN - OPUS4-62613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Habibimarkani, Heydar A1 - Abram, Sarah-Luise A1 - de Oliveira Guilherme Buzanich, Ana A1 - Prinz, Carsten A1 - Sahre, Mario A1 - Hodoroaba, Vasile-Dan A1 - Radnik, Jörg T1 - In-depth analysis of FeNi-based nanoparticles for the oxygen evolution reaction N2 - This study investigates the effect of varying iron-to-nickel ratios on the catalytic performance of Fe-Ni oxide nanoparticles (NPs) for the oxygen evolution reaction (OER). Addressing the issue of high energy wastage due to large overpotentials in OER, we synthesized and characterized different NP catalysts with different Fe: Ni oxide ratios. Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Spectroscopy (EDS), and X-ray Diffraction (XRD) were employed to determine the morphology, elemental and phase composition of the NPs. Furthermore, in-depth profiling with X-ray Photoelectron Spectroscopy (XPS) and Hard X-ray Photoelectron Spectroscopy (HAXPES) revealed that iron predominantly exists as oxide, while nickel exhibits both metallic and oxidic forms depending on the Fe content. XPS indicated an enrichment of iron at the NP surface, whereas HAXPES and EDS data agreed on the bulk stoichiometry. The assessment of the catalytic activity via cyclic voltammetry (CV) showed that the Fe: Ni ratio of 2:3 exhibited superior performance, characterized by lower overpotential and a smaller Tafel slope. KW - Fe-Ni oxide KW - Nanoparticles KW - OER KW - Catalytic performance KW - Cyclic voltammetry PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626932 UR - https://www.nature.com/articles/s41598-025-92720-3 DO - https://doi.org/10.1038/s41598-025-92720-3 VL - 15 IS - 1 SP - 1 EP - 17 PB - Springer Nature AN - OPUS4-62693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Strangfeld, Christoph A1 - Prinz, Carsten A1 - Hase, F. A1 - Kruschwitz, Sabine T1 - Data of embedded humidity sensors, sample weights, and measured pore volume distribution for eight screed types N2 - Four cement-based and four calcium-sulphate-based screed types are investigated. The samples have a diameter of 300 mm and a height of 35 or 70 mm. Up to ten humidity sensors are embedded directly during the concreting of the screed samples. Thus, the humidity over the sample height is monitored during hardening, hydration, evaporation, and oven drying. Furthermore, the screed samples are weighted during every measurement to determine the total mass and the corresponding moisture loss. To define the pore system precisely, mercury intrusion porosimetry as well as gas adsorption is performed. According to the data, the entire pore volume distribution is known. The measured pore diameters range from 0.8 nm to 100 μm and the total porosity of the examined screeds ranges between 11 % and 22 %. Based on these measurement data, moisture transport, pore saturation as well as sorption isotherms and their hysteresis may be calculated quantitatively as described by Strangfeld et al. KW - Concrete and screed KW - Material moisture KW - Pore volume distribution KW - Embedded humidity sensors KW - Data in brief PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-448261 UR - https://data.4tu.nl/repository/uuid:d2ba436f-78c0-4105-8a1f-5422fcb37851 DO - https://doi.org/10.4121/uuid:d2ba436f-78c0-4105-8a1f-5422fcb37851 SP - 1 EP - 4 PB - 4TU.Centre for Research Data CY - Delft AN - OPUS4-44826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Redda, Zinnabu Tassew A1 - Prinz, Carsten A1 - Yimam, Abubeker A1 - Barz, Mirko A1 - Becker, Katharina A1 - Gizaw, Desta Getachew A1 - Laß-Seyoum, Asnakech T1 - Structural and textural characterization of Brassica carinata biochar to investigate its potential industrial applications N2 - Biochar, a low-cost, and carbon-rich product of the thermal decomposition of biomass under oxygen-limited conditions and at relatively low temperatures, has recently been identified as a promising porous material with a wide range of industrial applications. In the present study, a comprehensive analysis of proximate, ultimate, nutrient profile, structural, and textural properties of a biochar derived from two Ethiopian indigenous Brassica carinata cultivars was conducted. The characterization of the biochar was achieved by employing a variety of well-established methods, including proximate analysis (moisture, volatile matter, ash content, and fixed carbon), ultimate analysis (C, S, and O content), atomic oxygen to carbon ratio (O/C), morphological and elemental composition analysis through scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS). Furthermore, a combination of mercury intrusion porosimetry (MIP), dynamic vapor sorption (DVS), and gas adsorption methods such as nitrogen and krypton gas adsorption, were used for an in-depth study of the porous structure. SEM morphological characterization showed that the biochar surfaces showed multiple pores of diverse sizes and shapes. EDS elemental composition analysis revealed that sodium, aluminium, and silicon were not detected, but potassium, calcium, magnesium, and iron were all present in noticeable amounts. Furthermore, ultimate analysis showed that the most prevalent elements were carbon (86 wt.%) and oxygen (10.41‒9.77 wt.%), while sulphur was present in negligible concentrations. MIP analysis demonstrated that the porosities of the biochars varied from 62.68 to 69.99 wt.%, with the Holetta-1 biochar showing the highest porosity. The superior porosity of Holetta-1, as confirmed via MIP analysis, yielded higher values for bulk volume (2.36 mL g− 1), skeletal volume (1.65 mL g− 1), and total intrusion volume (1.65 mL g− 1) compared to the Yellow Dodolla. The most frequent pore diameters were 172.46 μm for Yellow Dodolla and 111.42 μm for Holetta-1. The MIP log differential pore diameter distributions were observed to vary from 18 to 411 μm and 10 to 411 μm, respectively, for Yellow Dodolla and Holetta-1. Despite the biochars’ low specific surface areas (0.17–0.21 m² g⁻¹), krypton sorption was a suitable technique for its characterization compared to DVS and nitrogen sorption methods. In conclusion, the characterization studies confirmed that this carbon-rich porous material possesses unique and valuable properties, with these attributes position it as a promising alternative for diverse industrial applications, contributing to the development of a bio-based circular economy. KW - Morphological characterization KW - Mercury intrusion porosimetry KW - Gas adsorption PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655325 DO - https://doi.org/10.1038/s41598-025-32063-1 SN - 2045-2322 VL - 16 IS - 1 SP - 1 EP - 19 PB - Springer Science and Business Media LLC AN - OPUS4-65532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lisec, Jan A1 - Recknagel, Sebastian A1 - Prinz, Carsten A1 - Vogel, Kristin A1 - Koch, Matthias A1 - Becker, Roland T1 - eCerto—versatile software for interlaboratory data evaluation and documentation during reference material production N2 - The statistical tool eCerto was developed for the evaluation of measurement data to assign property values and associated uncertainties of reference materials. The analysis is based on collaborative studies of expert laboratories and was implemented using the R software environment. Emphasis was put on comparability of eCerto with SoftCRM, a statistical tool based on the certification strategy of the former Community Bureau of Reference. Additionally, special attention was directed towards easy usability from data collection through processing, archiving, and reporting. While the effects of outlier removal can be flexibly explored, eCerto always retains the original data set and any manipulation such as outlier removal is (graphically and tabularly) documented adequately in the report. As a major reference materials producer, the Bundesanstalt für Materialforschung und -prüfung (BAM) developed and will maintain a tool to meet the needs of modern data processing, documentation requirements, and emerging fields of RM activity. The main features of eCerto are discussed using previously certified reference materials. KW - Reference material KW - Statistics KW - Software KW - Collaborative trial PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-591851 DO - https://doi.org/10.1007/s00216-023-05099-3 SP - 1 EP - 9 PB - Springer Science and Business Media LLC AN - OPUS4-59185 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Prinz, Carsten A1 - Hase, Felix A1 - Kruschwitz, Sabine T1 - Data of embedded humidity sensors, sample weights, and measured pore volume distribution for eight screed types N2 - Four cement-based and four calcium-sulphate-based screed types are investigated. The samples have a diameter of 300 mm and a height of 35 or 70 mm. Up to ten humidity sensors are embedded directly during the concreting of the screed samples. Thus, the humidity over the sample height is monitored during hardening, hydration, evaporation, and oven drying. Furthermore, the screed samples are weighed during every measurement to determine the total mass and the corresponding moisture loss. To define the pore system precisely, mercury intrusion porosimetry as well as gas adsorption is performed. According to the data, the entire pore volume distribution is known. The measured pore diameters range from 0.8 nm to 100 µm and the total porosity of the examined screeds ranges between 11% and 22%. Based on these measurement data, moisture transport, pore saturation as well as sorption isotherms and their hysteresis may be calculated quantitatively as described in “Monitoring of the absolute water content in porous materials based on embedded humidity sensors” (Strangfeld and Kruschwitz, 1921). KW - Concrete and screed KW - Embedded humidity sensors KW - Pore volume distribution KW - Material moisture PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-462339 DO - https://doi.org/10.1016/j.dib.2018.09.020 SN - 2352-3409 VL - 21 SP - 8 EP - 12 PB - Elsevier CY - Amsterdam AN - OPUS4-46233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rübner, Katrin A1 - Prinz, Carsten A1 - Adolphs, Jürgen A1 - Hempel, S. A1 - Schnell, A. T1 - Microstructural characterisation of lightweight granules made from masonry rubble N2 - The pore structure of lightweight granules made from masonry rubble was studied in order to better understand their engineering properties. Thermally and hydrothermally hardened granules were tested. Analysis by ESEM, mercury porosimetry and sorption methods yield important insight into their microstructure. The thermal granules are characterised by partly melted vitreous areas and large internal macropores that are connected via narrow throats. They show a marginal specific surface area along with a hydrophobic behaviour. In contrast, the hydrothermal granules have an accessible mesoporous system containing plate-like and ink-bottle pores. The shape of their water isotherms depending on the granules’ CaO content is sensitive to the morphology of calcium silicate hydrate phases (CSH). The hysteresis changes from a narrow loop that closes at low pressures, which can be attributed to coarser more crystalline CSH, to a large triangular-shaped loop along with a low pressure hysteresis, which is characteristic for fine fibre-like CSH with ink-bottle and plate-like pore morphologies. Granules with fibre-like CSH have the higher specific surfaces areas but those with more crystalline CSH show stronger physisorption of water molecules. KW - Lightweight aggregates KW - Construction and demolition waste KW - Mercury porosimetry KW - Nitrogen sorption KW - Water vapour sorption PY - 2015 DO - https://doi.org/10.1016/j.micromeso.2014.08.060 SN - 1387-1811 SN - 1873-3093 VL - 209 SP - 113 EP - 121 PB - Elsevier Inc. CY - Amsterdam AN - OPUS4-32139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Harris, J. A1 - Mey, I. P. A1 - Böhm, C. F. A1 - Trinh, T. T. H. A1 - Fink, A. A1 - Bayer, F. A1 - Leupold, S. A1 - Prinz, Carsten A1 - Tripal, P. A1 - Palmisano, R. A1 - Wolf, S. E. T1 - Ultra-smooth and space-filling mineral films generated via particle accretion processes N2 - Nonclassical crystallization typically occurs via the attachment of individual nanoparticles. Intuitively, materials synthesized via this route should exhibit pronounced surface roughness and porosity as a hallmark of the formation process via particle accretion. Here, we demonstrate that nonclassical mineralization of calcium carbonate allows synthesis of ultra-smooth and dense surfaces with unprece-dented root-mean-square roughness of 0.285 nm, simply by con-trolling the hydration state of the nanosized building blocks using Mg doping. High fidelity coating of corrugated substrates can even be achieved. Nonclassical crystallization can thus lead to space-filling inorganic solid-state materials transgressing the implicit porosity commonly expected for particle-driven self-organization processes. KW - Nonclassical crystallization KW - Hydration KW - Particle accretion PY - 2019 DO - https://doi.org/10.1039/c9nh00175a VL - 4 IS - 6 SP - 1388 EP - 1393 PB - Royal Society of Chemistry AN - OPUS4-49488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Einhorn-Stoll, U. A1 - Prinz, Carsten A1 - Drusch, S. ED - Williams, P. A. ED - Phillips, G.O. T1 - Influence of storage on the water binding of pectin: determination by DSC N2 - Citrus pectins, necessary for the food industry and many other applications, are produced by large companies and distributed worldwide. On their way to the customers, the pectins may be stored under unfavourable environmental conditions for longer periods. This can alter their properties and affect their quality in the final application. It can be assumed that (1) pectins from different suppliers, produced from varying raw materials and under different processing conditions, have also varying material properties and water binding behaviour, and (2) the storage of pectins at 60 °C and 80 % humidity might alter these properties and the increase of hydrophilic groups might increase also their water binding ability. The aim of the present study was to investigate the water binding properties of different commercial pectins prior to and after storage by differential scanning calorimetry (DSC) at different water contents. T2 - 17th Gums & stabilisers for the food industry conference CY - Wrexham, UK DA - 25.06.2013 PY - 2014 SN - 978-1-84973-883-5 SN - 978-1-78262-130-0 DO - https://doi.org/10.1039/9781782621300-00147 SP - 147 EP - 154 AN - OPUS4-31135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -