TY - JOUR A1 - Konersmann, Rainer A1 - Otremba, Frank T1 - Vergleich von Risiken N2 - Vielen Entscheidungsprozessen geht ein Vergleich voraus. Bei einem Produktvergleich werden dazu Kriterien festgelegt, etwa der Kaufpreis, die Güte, Haltbarkeit, Handhabung usw. Der Testsieger ist meist derjenige, der die am höchsten bewerteten Kriterien erfüllt. Voraussetzung für derartige Vergleiche ist also die Gleichartigkeit der Vergleichsobjekte. Risiken untereinander zu vergleichen ist komplizierter. Die Notwendigkeit von Risikovergleichen ergibt sich, wenn nur unklare Vorstellungen, z. B. über die Risiken einer neuen Transporttechnologie, existieren und keine Erfahrungswerte zur Verfügung stehen. Aus bekannten und akzeptierten Risiken soll mittels eines Vergleichs die Tolerierbarkeit eines (noch) unbekannten Risikos abgeleitet werden. Der Beitrag setzt sich mit der Problematik von Risikovergleichen auseinander. KW - Risikovergleich Verkehrsmittel KW - Risikoakzeptanz KW - Qualitative Vergleichskriterien PY - 2013 SN - 2191-0073 VL - 3 IS - 6 SP - 32 EP - 37 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-28654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Alloy 800 steam generator tube stress corrosion cracks - detection and root causes T2 - Coteq 2013 CY - Porto de Galinhas, Brazil DA - 2013-06-18 PY - 2013 AN - OPUS4-28720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reich, Franziska A1 - Otremba, Frank A1 - Würsig, Andreas T1 - Fail-safe? A study about the integrity of safety valves for tanks for dangerous goods N2 - In Europe, tanks designed on different safety philosophies are used for transporting one and the same liquid dangerous goods (Krautwurst, 2011). Owing to this circumstance, the BAM was commissioned by the BMVBS to conduct a research project designed to analyse and assess the equipment of tanks. Furthermore in these project were researched some failure mechanism of pressure relief devices (PRD). Based on the knowledge gained, possible solutions were worked out under safety-relevant aspects that would benefit tank transport by providing a lower hazard potential. Besides looking at the mode of operation and the construction of PRV, their blow-off characteristics and total flow rate are considered from a safety engineering point of view. Based on in-depth studies, a concept for and the further approach to examinations of the failure limits of PRD, especially of spring loaded relief valves, was developed and comprehensively described in the report “The use of safety devices, particularly safety valves, on transport containers” (Pötzsch, Reich, & Jochems, 2011). The purpose of this study was to investigate failure causes of safety valves by normal modes and accidental fire heat loads. A series of investigations for different influences using safety valves for tanks were obtained. Testing vibration modes and corrosion presents some design limits. Experimental study of a pressure vessel engulfing in fire identify significant design limits. The complete set of results provides direct information of fail-safe modes and discusses the usage. T2 - ASME 2013 International mechanical engineering congress and exposition CY - San Diego, CA, USA DA - 15.11.2013 KW - Safety valves KW - Transporttanks KW - Dangerous goods KW - Fire prooving KW - Response behavior PY - 2013 IS - IMECE2013-62204 SP - 1 EP - 5 AN - OPUS4-29717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Integrity of aluminium gas receptacle T2 - IMECE 2013 CY - San Diego, CA, USA DA - 2013-11-15 PY - 2013 AN - OPUS4-29668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero Navarrete, J. A. A1 - Otremba, Frank A1 - Lozano Guzmán, A. A. T1 - Experimental-theoretical modelling of the lateral sloshing in rail tankers N2 - The objective of this paper is to describe and to validate a simplified pendulum-analogy model to simulate the interaction of a liquid cargo with ist carrying vehicle. The resulting testing rig consists of a rectangular container, spring supported on a two wheelset-bogie having a scale down of 1/10 with respect to a full-size equipment. The testing rig is used to validate a simple pendulum-based, simplified three degree-of-freedom mathematical model of the response of a partially filled container to lateral accelerations. The length of the pendulum is set according to validated methodologies. The resulting mathematical scheme reveals a high correlation with the experimental output, on the order of 99%, while some other performance measures, related to the peak forces and the range of variation of the wheel-rail forces, also show good concordance with the experimental results. KW - Sloshing KW - Rail tankers KW - Pendulum analogy KW - Experimental modelling KW - Mechanical fatigue PY - 2021 DO - https://doi.org/10.1504/ijhvs.2021.117504 VL - 28 IS - 3 SP - 435 EP - 454 AN - OPUS4-53101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero Navarrete, J. A. T1 - Assesing rail damage in turns due to lateral load transfer N2 - A testing procedure is proposed and used, to estimate the rail damage potentials of variations in both, the height of the cargo´s center of gravity and the railway car suspension´s spring constant. The experimental setup consisted of a tilt table that slowly exerted an increasing lateral acceleration on a two-axle bogie-type vehicle equipped with a spring supported container. The potential damaging effect derived from the resulting lateral load transfer, was assessed on the basis of the fourth-power law. Results suggest that the cargo having a higher center of gravity could be more damaging to the outside rail when compared with the effect of the shorter center of gravity of the cargo, in arrange from0.94% to 3.17%, as a function of the spring constant of the suspension. Consequently, and comparatively, there would be a long-term damaging effect on the rail when having a cargo with a higher center of gravity, so that specific cargo, having a high center of gravity, would be more aggressive to the infrastructure. On the other hand, for the range of time rate changes of the lateral acceleration, it was not found a consistent trend regarding the effect of the value of the spring constant on the magnitude of the load transfers. T2 - ASME 2024 CY - Portland, OR, USA DA - 17.11.2024 KW - Rail demage KW - Lateral load transfer PY - 2024 AN - OPUS4-61784 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero-Navarrete, José A. A1 - Otremba, Frank T1 - A testing facility to assess railway car infrastructure damage N2 - Wheel forces generate stresses in the rail as a function of several vehicle and infrastructure characteristics and operating conditions. The different components of the wheel forces develop strains in the rail which contain an elastic and hysteretic (irreversible) components. The irreversible deformations of the rail would be associated with locomotive energy losses. In this paper, a testing facility is proposed to indirectly characterize the level of stresses in the rail, in terms of the energy that is lost during tuming maneuvers. Different potentially influential factors are considered, including the friction at the Center plate, the wheelbase length, the distance between bogies and the radius of the curved track. The change in the potential energy during a U-turn displacement is measured. In this respect, an experimental model under this operating principle, aimed at validating such a principle of Operation, reveals a significant effect of the friction at the center plate on the energy lost during turning maneuvers, and consequently, on the level of stresses in the rail. T2 - COMPRAIL 2020 - 17th International Conference on Railway Engineering Design & Operation 2020 CY - Online meeting DA - 01.07.2020 KW - Energy losses in transportation KW - Experimental methods KW - Friction energy KW - Rail damage KW - Turning forces KW - Wheel forces PY - 2020 DO - https://doi.org/10.2495/TDI-V4-N2-142-151 SN - 2058-8305 VL - 4 IS - 2 SP - 142 EP - 151 PB - WitPress AN - OPUS4-51125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Otremba, Frank A1 - Hildebrand, R. A1 - Romero Navarrete, J. A. A1 - Sklorz, Christian ED - Otremba, Frank T1 - A simplified analytical approach on the dynamic pressures in cylindrical vertical tanks N2 - A simplified methodology is proposed to estimate the dynamic pressures developed within partially filled cylindrical vertical tanks when subjected to earthquake-related horizontal accelerations. The total pressure at the bottom of the tank is calculated as the superposition of vertical and horizontal pressures. While the magnitude of the vertical pressure depends on the free surface height of the liquid, the horizontal pressure depends on the magnitude of the horizontal acceleration and on the diameter of the tank. The liquid free surface oscillation angle is simulated based upon the principles of the simple pendulum analogy for sloshing. The length of the pendulum, however, is set on the basis of a methodology to calculate the free sloshing frequency of partially filled containers. Such a methodology is experimentally verified in this work. The outputs of the model for full scale situations, suggest that the lateral perturbation - sloshing phenomenon (earthquake effect) can generate an increase in the total pressure of 56% above the no lateral perturbation situation, further suggesting that such an overpressure should be taken into account when designing tanks that could be potentially subjected to earthquake-related perturbations. KW - Vertical cylindrical tanks KW - Pendulum analogy KW - Experimental approach KW - Sloshing, transition matrix approach KW - Hazmat PY - 2021 SN - 978-981-15-8273-8 SP - 1 EP - 15 PB - Springer AN - OPUS4-51982 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Romero-Navarrete, José A. A1 - Hurtado-Hurtado, G. ED - Pucheta, M. ED - Cardona, A. ED - Preidikman, S. ED - Hecker, R. T1 - Determination of the Effect of Sloshing on the Railcar-Track Dynamic Behavior N2 - This paper presents the study of the impact caused by a liquid Cargo on a railway infrastructure. The dynamic behavior of a tank car corresponds to a multibody dynamic system with several degrees of freedom. This study’s data were obtained from a scale experimental fixture consisting of a track and a railcar with a tank. The track was instrumented with strain gauges and the railcar with accelerometers. The data showed non-periodic and periodic terms; therefore, the results were analyzed with the Empirical Mode Decomposition method (EMD). It was found that the EMD identified the signal components that were related to the sloshing. These components represent the mode shapes of the original signal. The location of the sloshing in the track was found applying spectrograms to the accelerometer data. This paper’s experimental outputs suggest that the sloshing effect is detectable at the track and in the vehicle dynamics. KW - Sloshing effect KW - Empirical Mode Decomposition KW - Wheel/track interaction KW - Multibody dynamics PY - 2021 SN - 978-3-030-88750-6 DO - https://doi.org/10.1007/978-3-030-88751-3_14 SP - 131 EP - 140 PB - Springer Nature Switzerland AG AN - OPUS4-53561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Lozano Guzman, A. A. T1 - Estimation of the effect of the driving style on pollutants emission by heavy trucks N2 - Different approaches have been attempted so far to reduce fuel consumption and linked pollutants, including vehicle equipment and design, with rational driving style being recognized as a potential source of fuel savings. However, no specific methodology had been suggested so far to assess fuel economy of driving other than the fuel consumed itself. In this paper, the Standard deviation of driving acceleration has been found to be directly associated to fuel consumption, so that the less dispersion of the driving acceleration, produces the lower fuel consumptions and emissions. Such metric could be thus used to assess driving style. KW - Driving style KW - Fuel consumption KW - Stored energy KW - GPS data KW - Simulation KW - Particle emissions PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-511540 UR - https://www.iaras.org/iaras/home/caijes/estimation-of-the-effect-of-the-driving-style-on-pollutants-emission-by-heavy-trucks SN - 2367-8941 VL - 5 SP - 220 EP - 226 PB - IARAS CY - Sofia AN - OPUS4-51154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero-Navarrete, José A. A1 - Otremba, Frank T1 - A method to assess the gravity response efficiency of a truck N2 - In spite that transport activities do not represent the biggest contributor of pollutants emissions, their reduction has been a priority as some other externalities are associated to such emissions and to the transport itself. A crucial element to characterize the behavior of the vehicles against the environment are the losses that such vehicles exhibit in a passive way, that is, without any involvement of power conditions. The energy loses due to the rolling, the drag and to the friction in mechanical components, have been assessed so far in terms of the stopping acceleration when the vehicle idles on a ramp. However, such a testing procedure produces some uncertainties due to the dynamic conditions that are considered. To avoid such critical limitations, in this paper a testing procedure and facility are proposed, which are based on static conditions of the vehicle at the initiation and at the ending of the test, which are assumed to provide a better reliability to the testing. Some preliminary theoretical analysis should be made in order to validate the operational principles proposed herein for such testing facility. KW - Road tankers KW - Energy efficiency KW - Environmental assessment KW - Gravity response KW - Transportation energy KW - Rolling resistance KW - Drag resistance PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-511530 UR - https://www.iaras.org/iaras/home/caijes/a-method-to-assess-the-gravity-response-efficiency-of-a-truck SN - 2367-8941 VL - 5 SP - 213 EP - 219 PB - IARAS CY - Sofia AN - OPUS4-51153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hurtado-Hurtado, G. A1 - Morales-Velazquez, L. A1 - Valtierra-Rodríguez, M. A1 - Otremba, Frank A1 - Jáuregui-Correa, J. C. T1 - Frequency Analysis of the Railway Track under Loads Caused by the Hunting Phenomenon N2 - Hunting is a potentially dangerous phenomenon related to the lateral oscillation of the wheels that impacts the rails and causes the wear of the infrastructure’s components. Therefore, the analysis and timely detection of hunting can lead to the application of corrective maintenance tasks, reducing damages, and costs and even derailments as a result. In this work, the vibration response of a finite element model of a rail with hunting-induced loads by a single wheel is analyzed in three directions: longitudinal, lateral, and vertical. The contact patch forces are calculated by means of Simpack® using the Kalker linear theory and the contact Hertz theory. The system is solved by using the Newmark-_ approach. The results of the deflection and vibration analysis, following the proposed methodology, show how the different characteristics of the loads impact the rail. KW - Continuous wavelet transform KW - Empirical mode decomposition KW - Finite element method KW - Frequency analysis KW - Hunting phenomenon KW - Mechanical modelling KW - Rail vibrations PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-551517 UR - https://www.mdpi.com/2227-7390/10/13/2286/htm# DO - https://doi.org/10.3390/math10132286 VL - 10 IS - 13 SP - 1 EP - 17 PB - MDPI AN - OPUS4-55151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jauregui-Correa, J. C. A1 - Morales-Velazquez, L. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. T1 - Method for predicting dynamic loads for a health monitoring system for subway tracks N2 - This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method. The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data. KW - Health monitoring KW - Transfer function KW - Railroad KW - Substructure failures KW - Dynamic loads PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557480 DO - https://doi.org/10.3389/fmech.2022.858424 SN - 2297-3079 VL - 8 SP - 1 EP - 16 PB - Frontiers Media CY - Lausanne AN - OPUS4-55748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hurtado-Hurtado, G. A1 - Morales-Velazquez, L. A1 - Otremba, Frank A1 - Jáuregui-Correa, J. C. T1 - Railcar Dynamic Response during Braking Maneuvers Based on Frequency Analysis N2 - The dynamic response of a vehicle during braking is influenced by the tangential forces developed at the wheel-rail’s contact surface. The friction coefficient affects the load transfer from the wheel’s tread to the vehicle. In this work, the vibrations of a scale-down railway vehicle are monitored during braking and their relationship with the friction coefficient between wheel and rail is found out. The vehicle is instrumented with encoders, accelerometers, and is controlled via Bluetooth. The tests are carried out with clean and friction-modified rails. The tangential forces transmitted from the wheel to the railcar’s body are visualized in time and frequency using a proposed correlation algorithm based on the outputs of the ContinuousWavelet Transform (CWT). The results demonstrate that tangential forces have a significant impact on railway vehicles under conditions of high friction coefficients and large creep values. KW - Railway vibration measurements KW - Vibration signal analysis KW - Wheel-rail tangential forces KW - Railway braking forces KW - Wheel-rail friction coefficient PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572309 DO - https://doi.org/10.3390/app13074132 VL - 13 IS - 7 SP - 1 EP - 15 PB - MDPI AN - OPUS4-57230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - A lowering friction treatment for railway materials N2 - A facility is proposed in this paper to apply a selective carburizing process to the lateral faces of a railways´ head, aiming to increase its carbon content and to decrease the friction coefficient in case that the flange of the railway car wheel gets in contact with the rail during turning. Such a treatment would reduce the energy that is lost during the turning maneuvers performed by the vehicle, further improving the energy efficiency of the railway car. The facility consists of a furnace, which should be set next to the rails´ hot-rolling facility, in order to use the available enthalpy. The proposed furnace is equipped with what is necessary to avoid the decarbonization of the remaining rail material, based upon batteries of oxy-acetylene burners that are installed at the bottom of the furnace, on the opposite side to the carburizing surface. An experimental facility is necessary to validate the operational principles for the equipment proposed in this paper. On the other hand, a study should also be carried out to assess the effect of any rail welding process on the carburized surfaces. KW - Transport efficiency KW - Dry friction KW - Carburizing KW - Selective carburizing KW - Decarbonization KW - Furnace design PY - 2020 DO - https://doi.org/10.5185/amlett.2020.041498 VL - 11 IS - 4 SP - 2004198 PB - IAAM - VRBI Press AN - OPUS4-50958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero-Navarrete, José A. A1 - Otremba, Frank T1 - Vehicle’s components damage N2 - The failure of vehicle’s suspension components has contributed to road crashes, while their defective operation can deteriorate the fuel efficiency of the vehicles. In this context, and when compared with solid cargo transporters, the road tankers would tend to produce larger roll forces during turning, as the curved shape of the liquid cargo container, shifts upwards the centre of gravity of the cargo. With reference to a rectangular cargo container representing the solid cargo situation, the increase in the position due to elliptical and circular tank shapes, can attain a value of 17% (100% fill, circular tank). In this study, experimental results comparing the lateral load transfer due to solid and liquid cargoes, indicate that the average force increase on the vehicle’s load-receiver side due to a liquid cargo, is 4.3%. To analyse the fullscale situation of both situations, that is, the higher position of the centre of gravity and the shifting of the liquid cargo, a simplified model is developed. The outputs from such a model when subjected to realistic operating conditions (speed and turning radius), suggest that the higher position of the centre of gravity due to using a non-rectangular cargo container generates an average force increase of 4.9% on the side receiving the load transfer. The incorporation of the effect of the liquid cargo, through the simple pendulum analogy, suggests that such an average increases to 6.76%, with a maximum of 8.35% in the case of the elliptical tank at 75% fill level. It is found that the average liquid cargo effect is 5.44%, which should be compared with the 4.3% of the experiments. Road tankers components would thus have a relatively shorter load cycle life than those of the solid cargo trucks. KW - Liquid cargo KW - Load transfer KW - Roll reactions KW - Experimental modelling KW - Pendulum-analogy PY - 2020 DO - https://doi.org/10.1177/0954407020960543 VL - 235 IS - 2-3 SP - 446 EP - 454 PB - Sage Journals AN - OPUS4-51386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. ED - Romero-Navarrete, José A. T1 - A Conceptual Design of a Self-Centering Centre Plate N2 - Turning maneuvers originate higher forces exerted on the rail and the loss of locomotive energy, at a rate that is function of several parameters that influence the magnitude of the developed horizontal wheel-rail forces, including the friction at the centre plate and the bogie´s yaw stiffness. However, such a friction at the contact surfaces of the centre plate is needed to mitigate the Hunting phenomenon when the train moves on straight track segments. In this paper, a self-centering centre plate is proposed, consisting of a lubricated centre plate, equipped with a spring- and damper-based self-centering mechanism. Simulation results of the proposed mechanism suggest that the energy performance in turns of a train car equipped with such self-centering centre plate is comparatively better, as the peak friction forces linked to the dry friction at the contact surfaces of current centre plate designs, are avoided. The assessment of the hunting performance of the proposed device in straight track segments is proposed as the continuation of this work. KW - Bogie´s yaw stiffness KW - Bogie´s yaw friction KW - Centre plate KW - Self-centering mechanism KW - Turning PY - 2020 UR - https://publications.waset.org/aerospace-and-mechanical-engineering SN - 1307-6892 VL - 14 IS - 9 SP - 376 EP - 382 AN - OPUS4-51241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kutz, Philipp A1 - Otremba, Frank A1 - Werner, Jan T1 - Mechanical and Thermal Properties of Composite Material and Insulation for a Single Walled Tank for Cryogenic Liquids N2 - This paper describes the testing methods used to determine the thermal properties of insulation materials and mechanical properties of materials used for the load-bearing structure for pressure tanks (up to 4 bar, relative) and cryogenic liquids (LNG, −166 °C to -157 °C at atmospheric pressure). Goal is to design a transportation tank that does not exceed 4 bars (relative) within 10 h, starting at atmospheric pressure. PUR-foam is a suitable material for the insulation. A 12,5 l small scale tank prototype reached 4 bar (relative) within 87 minutes, which is, regarding the influence of the size, a satisfying result. The mechanical properties change significantly at cryogenic temperatures. The bending modulus is similar at first, but decreases at a certain point by appr. 50 %. However, the maximum stress is much higher and could not be reached within this testing setup. T2 - 26th Assembly Advanced Materials Congress CY - Stockholm, Sweden DA - 10.06.2019 KW - GFRP KW - LNG KW - Lightweight design KW - Thermal properties KW - Mechanical prtoperties PY - 2020 DO - https://doi.org/10.5185/amlett.2020.011457 VL - 11 IS - 1 SP - 1 EP - 6 PB - VBRI Press AN - OPUS4-50216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Sklorz, Christian A1 - Martínez Madrid, M. T1 - Quasistatic rollover threshold of atmospheric road tankers N2 - Several geometrical analytical tools can be used for assessing the potential benefits of any alternative tank shape. The quasistatic evaluation of the cargo-vehicle behavior represents a fast way to objectively determine the roll stability benefits of any potentially new tank shape. In this paper, the geometrical, quasistatic rollover performance of a convex bottom tank shape is compared with that of standard tank shapes, finding that in spite of the lower position of the cargo´s center of gravity in such a tank shape for the un-perturbed condition, it has the same performance as the elliptical tank shape when subjected to Steady lateral acceleration. That as a result of the large cargo´s lateral displacement. Consequently, the combination of a lower center of gravity for the cargo when it is not perturbed, and a Minimum lateral shift due to lateral accelerations inputs, define the conditions for an ideal tank shape. T2 - CONIIN 2020 CY - Online meeting DA - 28.09.2020 KW - Tank shape KW - Road tankers KW - Center of gravity shifting KW - Quasistatic KW - Convex bottom KW - Geometrical analysis PY - 2020 SP - 1 EP - 6 AN - OPUS4-51388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Lozano Guzmán, A. A. T1 - An energy frame of reference to assess vehicle´s physical externalities N2 - Externalities of the road transportation are multidimensional in nature and involve the road-vehicle interaction under different environmental conditions. Estimating the pavement and vehicle damage potentials as a function of the condition sunder which such interaction takes place, is important to avoid accelerated or catastrophic damages in these systems. Such an assessing is crucial from the perspective of pricing the effects of the vehicle on the infrastructure and vice versa. The existing models for pricing such interaction, critically depends on gross average statistical models. In this paper, it is proposed a deterministic approach to realize such an assessment, based upon validated approaches for the pavement damage. The simulation scheme considers different degrees-of-freedom vehicle models, and a discrete asphalt pavement, that make possible the simulation of massive traffic situations on realistic road lengths. T2 - IMECE 2020 CY - Online meeting DA - 16.11.2020 KW - Energy KW - Frame KW - Assess KW - Vehicles PY - 2020 SP - 1 EP - 9 AN - OPUS4-51645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -