TY - JOUR A1 - Otremba, Frank A1 - Heming, Frank T1 - Rückendeckung N2 - Sicherheit - Trotz des Spotts anderer Europäer, 'Auffahrunfälle gebe es nur in Deutschland', wird das Ziel eines Anfahr- statt Unterfahrschutzes für das Tankfahrzeugheck hierzulande weiter verfolgt. PY - 2013 SN - 0016-5808 VL - 3 SP - 14 EP - 17 PB - Storck CY - Hamburg AN - OPUS4-27745 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Alexander, I. A1 - Braun, H.-J. A1 - Dettmann, T. A1 - Fimmen, H. A1 - Haberkamp, H. A1 - Katz, H. A1 - Krischok, Frank A1 - Otremba, Frank A1 - Pötzsch, Klaus-Michael A1 - Zentgraf, R. A1 - Putzschke, M. T1 - Bericht über den Ablauf und die Ursachen der Havarie des Tankmotorschiffes 'Waldhof' am 13. Januar 2011 auf dem Mittelrhein (Rhein-km 553,75) KW - Schiffshavarie KW - Gefahrgut-Tankschiff KW - Schwimmstabilität PY - 2013 IS - S-312.4/016 SP - 1 EP - 224 AN - OPUS4-27729 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Borch, Jörg-Peter A1 - Otremba, Frank A1 - Balke, Christian A1 - Burghardt, Frank T1 - Sicherheit von Flüssiggasflaschen im Unfallfeuer N2 - Neben herkömmlichen Stahlflaschen, die seit Jahrzehnten in fast unveränderter Bauform für Flüssiggase (Propan-Butan-Gemische) eingesetzt werden, etablieren sich immer mehr Flaschen aus Faserverbundwerkstoffen (GFK) mit einer geringeren Masse. Die Bundesanstalt für Materialforschung und -prüfung (BAM) wurde beauftragt, das Verhalten dieser Gasflaschen unter den extremen Bedingungen eines Unfallfeuers zu untersuchen. In einem Brandprüfstand der BAM auf dem Testgelände Technische Sicherheit (TTS) in Horstwalde wurden deshalb beide Typen von Propangasflaschen einem simulierten Unfallfeuer ausgesetzt. KW - Gefahrgut KW - Flüssiggas KW - Flaschen KW - Unfallfeuer KW - Druckgefäße KW - Gefahrguttransport PY - 2013 SN - 2191-0073 VL - 3 IS - 11/12 SP - 44 EP - 47 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-29720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Schwarzer, Stefanie A1 - Otremba, Frank ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Comparison of the operating life of tank containers, tank vehicles and rail cars for the carriage of dangerous goods in practice, analysis of causes of damage N2 - More than 400 Mt of dangerous materials are transported in Germany every year, of which 150 Mt are by road. Tank containers, tank vehicles and rail tank cars are used for the carriage of dangerous goods in large quantities. Data on the operating life of tanks are only available, in practice, to a minor degree. They are only partly published, mainly after accidents. The BAM-List - Requirements for Tanks for the Carriage of Dangerous Goods, which has compatibility evaluations of metallic and polymeric materials, has been the basis for substance-related prototype approvals for tank containers and portable tanks designed for the carriage of dangerous goods by the BAM since publication of the first edition in 1989. These data are also used for the approval of rail tank cars and road tank cars and are used as a source of knowledge not only in Germany but also worldwide. Tank leakages caused by tanks or rail tank cars being made of tank and sealing materials which are not resistant to the fill goods are avoided by using the material resistance data of the BAM. Corrosion damage is among the main causes of damage. Uniform and non-uniform area corrosion without mechanical stress in aqueous substances is one of the most frequent types of corrosion during the transport of chemicals in tanks. Much damage by pitting corrosion occurs during the transport of substances containing chlorides or substances which separate chloride ions in the presence of moisture. Operational stresses are caused by the effects of both the road and the dangerous goods being transported. Mechanical damage often results from long-term overstressing and occurs after longer operating times. Operational failures cause damage which may appear during the service of tank containers, road tank cars or rail tank cars. The damage results from the inattention of employees when opening and closing the valves. Traffic accidents also cause damage to tanks and frames. Many cases of damage are due to weld area cracks resulting from four basic errors in construction, material, manufacturing and operation. Manufacturing errors can be undetected and the starting point of cracks which only grow under service conditions. Manufacturing errors result from variations in measurement and design, fittings, state of surface (hardness, abrasiveness) and mechanical surface damage (scratches, cracks). Incorrectly welded joints and errors during mechanical deformation are typical mistakes when installing the component parts. Variations in the wall thickness or combinations of different materials lead to manufacturing errors too. A lot of tanks are not used for the transport of dangerous goods before the end of their service life as they do not fulfil the revised technical safety requirements in the Dangerous Goods Regulations. Predictions in the BAM-List based on literature data and corrosion test results are reflected in the service (operating) life. Rail tank cars made of carbon steel, for example, which are mainly used for the transport of petroleum products, can achieve a service life of 40 – 50 y. Rail tank cars produced of austenitic CrNi- or CrNiMo-steel can reach an operating life of at least 30 y, whereby the corrosiveness of the transport substances plays an important role. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Gefahrguttanks KW - Eisenbahnkesselwagen KW - Schadensursachen KW - Lebensdauer PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331094 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 31 SP - 559 EP - 564 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Erhard, Anton T1 - Alloy 800 steam generator tube stress corrosion cracks - detection and root causes T2 - Coteq 2013 CY - Porto de Galinhas, Brazil DA - 2013-06-18 PY - 2013 AN - OPUS4-28720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Otremba, Frank A1 - Mohr, F. A1 - Kilian, R. T1 - Alloy 800 steam generator tube stress corrosion cracks - detection and root cause KW - Tube inspection PY - 2012 SN - 0007-1137 VL - 54 IS - 6 SP - 1 EP - 5 PB - British Institute of Non-Destructive Testing CY - Northampton AN - OPUS4-26006 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Schuler, X. A1 - Otremba, Frank T1 - A new concept for steam generator tube integrity assessment N2 - Steam generator (SG) tubes are part of the primary circuit of pressurised water reactors and therefore also part of the pressure retaining boundary components. Furthermore, steam generator tubes are the components which guarantee the separation between the primary and secondary circuits. Therefore the knowledge of the loss of tube integrity as soon as possible is an essential. Optimised nondestructive testing methods based on the eddy current array technique are used to find material degradation, especially intergranular stress corrosion cracks during the periodical in-service inspection. These methods are supported by the measurement of the leakage rate during operation based on radioactivity and Tritium measurement regarding a high crack grows. Shutdown criteria depending on leakage rates which are described in the operation procedures but there are no specifications about the conditions for the measured leakage. Is the leakage coming from a single crack or are there multiple cracks or is this the leakage of a critical crack. With the help of FE calculations answer about the uncertainties of leakage rate versus critical crack grows were found. Shutdown criteria must guarantee to avoid critical crack sizes, i.e. between the measured tritium activity and the critical crack size must be a safety gap. KW - Steam generator tubes KW - Crack detection KW - Non destructive testing KW - Axial cracks KW - Critical crack sizes KW - Crack opening area KW - Leakage PY - 2012 DO - https://doi.org/10.1016/j.nucengdes.2012.04.014 SN - 0029-5493 SN - 1872-759X VL - 249 SP - 297 EP - 303 PB - North-Holland Publ. Co. CY - Amsterdam AN - OPUS4-26025 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Reich, Franziska T1 - Strukturoptimierung von Rahmenwerken von Druckgasbehältern in Containereinheiten T2 - BAM / IGV Jahresgespräch 2013 CY - Berlin, Germany DA - 2013-02-19 PY - 2013 AN - OPUS4-27859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Reich, Franziska A1 - Sklorz, Christian T1 - Forschen für die Sicherheit T2 - Gefahrgut-Techniktage 2013 CY - Hamburg, Germany DA - 2013-02-25 PY - 2013 AN - OPUS4-27860 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konersmann, Rainer A1 - Otremba, Frank T1 - Vergleich von Risiken N2 - Vielen Entscheidungsprozessen geht ein Vergleich voraus. Bei einem Produktvergleich werden dazu Kriterien festgelegt, etwa der Kaufpreis, die Güte, Haltbarkeit, Handhabung usw. Der Testsieger ist meist derjenige, der die am höchsten bewerteten Kriterien erfüllt. Voraussetzung für derartige Vergleiche ist also die Gleichartigkeit der Vergleichsobjekte. Risiken untereinander zu vergleichen ist komplizierter. Die Notwendigkeit von Risikovergleichen ergibt sich, wenn nur unklare Vorstellungen, z. B. über die Risiken einer neuen Transporttechnologie, existieren und keine Erfahrungswerte zur Verfügung stehen. Aus bekannten und akzeptierten Risiken soll mittels eines Vergleichs die Tolerierbarkeit eines (noch) unbekannten Risikos abgeleitet werden. Der Beitrag setzt sich mit der Problematik von Risikovergleichen auseinander. KW - Risikovergleich Verkehrsmittel KW - Risikoakzeptanz KW - Qualitative Vergleichskriterien PY - 2013 SN - 2191-0073 VL - 3 IS - 6 SP - 32 EP - 37 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-28654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwarzer, Stefanie A1 - Weltschev, Margit A1 - Otremba, Frank T1 - Lebensdauer und Schadensursachen von Tankcontainern, Tankfahrzeugen und Kesselwagen zur Beförderung von Gefahrgütern in der Praxis N2 - Daten über Schadensursachen und die tatsächliche Nutzungsdauer der Tanks zum Transport von Gefahrgütern liegen nur in begrenztem Maße vor. Auf der Basis der Daten von Tankbaufirmen, Speditionen und Eisenbahnkesselwagen-Vermietgesellschaften wurde die durchschnittliche Lebensdauer von Tankcontainern, Tankfahrzeugen und Kesselwagen zur Beförderung von Gefahrgütern in der Praxis ermittelt und die Hauptschadensursachen analysiert. Korrosion, Risse an Schweißnähten, Gestaltungs- und Dimensionierungsfehler sowie fertigungs- und betriebsbedingte Fehler zählen zu den Hauptschadensursachen. Viele Tanks werden vor Ablauf ihrer Nutzungsdauer nicht mehr für den Transport von Gefahrgütern eingesetzt, da sie nicht mehr den geänderten gesetzlichen Anforderungen in den Gefahrgutvorschriften entsprechen. Die Voraussagen durch Literaturangaben und Ergebnisse von Korrosionsversuchen in der BAM-Liste – Anforderungen an Tanks zur Beförderung gefährlicher Güter – spiegeln sich in der Nutzungsdauer/Lebensdauer der Tanks wider. KW - Gefahrguttransport KW - Tankcontainer KW - Tankfahrzeuge KW - Eisenbahnkesselwagen KW - Schadensursachen KW - Lebensdauer PY - 2011 SN - 2191-0073 VL - 1 IS - 11/12 SP - 28 EP - 33 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24972 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Bäßler, Ralph A1 - Otremba, Frank T1 - Use of higher-alloyed metallic materials and duplex steels for transport tanks of dangerous goods N2 - Compatibility evaluations of selected metallic materials under the influence of dangerous goods are published in the BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” as basis for substance-related prototype approvals for tank Containers designed for the carriage of dangerous goods. There is a request of the tank manufacturing industry and transportation Companies to incorporate additional materials into the BAM-List, especially corrosion-resistant materials because of the large number of corrosive dangerous goods. One solution to solve corrosion Problems is to line the tank with a polymer, an alternative solution is the application of high-alloyed stainless steels and nickel-based alloys as there are 1.4529 (XINiCrMoCu 25-20-7, alloy 926), 1.4562 (X1NiCrMoCu32-28-7, alloy 31) and 2.4605 (NiCr23Mo16AI, alloy 59). There is an interest to use cost-efficient steels with high strength values and concomitant adequate corrosion resistance such as duplex steel 1.4362 (X2CrNiN23-4). This steel grade was originally developed as a substitute for the austenitic grades 1.4404 (X2CrNiMo17-12-2) and 1.4571 (X6CrNiMoTi17-12-2). Due to the lower content of the alloy elements nickel and molybdenum this duplex steel is a cost-efficient alternative to molybdenum containing austenite. Due to the limited number of corrosion test results with welded test samples of these high-alloyed materials and the duplex steel under the influence of corrosive dangerous goods a comprehensive test Programme was performed with these materials in Cooperation with ThyssenKrupp VDM and Deutsche Edelstahlwerke GmbH. It can be concluded from the test results that the superaustenitic steels 1.4529 and 1.4562 as well as the nickel-based alloy 2.4605 are a really good alternative as tank materials for the transport of dangerous goods in comparison to the lining of the tanks. The nickel-based alloy 2.4605 shows the best resistance and is suitable as material for tanks transporting all tested corrosive substances. One exception is the temperature limit during the transport of hydrochloric acid. The superaustenit 1.4562 is a resistant material with a wide ränge of application. Exceptions for use are: ammonium bifluoride, brine, 34 % calcium Chloride solution, hydrochloric acid, perchloric acid, 90 % 2-chloropropionic acid, nitrating acid with nitric acid content > 50 % and molten monochloroacetic acid. The alloy is limited suitable for allyl Chloride, aluminum Chloride, copper (II) -Chloride and ferric Chloride. The superaustenit 1.4529 showed the lowest resistance compared to the other two materials. This steel is not resistant in hydrochloric acid, perchloric acid, sodium Chlorite and sodium hypochlorite. The application is limited in the concentration ränge of aqueous Solutions of aluminum Chloride, copper (II) Chloride and ferric Chloride. Due to the reduced alloying content of the duplex steel 1.4362 (X2CrNiN23-4) compared to the austenitic CrNiMo-steels, a lower resistance especially in acidic media like formic, acetic or sulfuric acid was observed. Within the more than 7.000 substances contained in the BAM-List there is a large amount of dangerous goods such as hydrocarbons, alcohols, aldehydes, ketones, ethers, esters, and inorganic alkaline substances which have a large transport volume and do not corrode the duplex steel 1.4362 (X2CrNiN23-4). The test results are included in the actual 11th edition of the BAM-List and therefore available for the costumer. T2 - Stainless steel world conference & exhibition 2011 CY - Maastricht, The Netherlands DA - 29.11.2011 KW - Duplexstahl KW - Tankcontainer KW - Tankfahrzeuge KW - Beständigkeitsbewertung KW - BAM-Liste PY - 2011 SP - 1 EP - 12 PB - KCI Publ. AN - OPUS4-24975 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - German concept of break exclusion T2 - Quadripartite Working Group Meeting CY - Paris, France DA - 2008-10-09 PY - 2008 AN - OPUS4-18137 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Application of Lifetime Management for mechanical Systems, Structures and Components (SSC) in Nuclear Power Plants T2 - Technical Meeting on Current Trends on Nuclear Reactor Safety Aspects and Their Uses in the Development of an Update of the Regulatory Approach - Seventh Mission - November 2008 CY - Rio de Janeiro, Brazil DA - 2008-11-15 PY - 2008 AN - OPUS4-18176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pötzsch, Klaus-Michael A1 - Würsig, Andreas A1 - Otremba, Frank T1 - Das Gefahrgutrecht für Tanks und die technische Norm N2 - Im Gefahrgutrecht, insbesondere im Bereich der Gefahrguttanks für den Landverkehr, hat der Bezug zur technischen Norm aufgrund der Rechtsfortentwicklung eine fundamentale Bedeutung erlangt. Damit die Interessen der deutschen Tankhersteller genügend Berücksichtigung finden können, ist die kontinuierliche Mitarbeit der betroffenen Wirtschaftskreise in den nationalen und internationalen Normungsgremien erforderlich. Dieser Zusammenhang, der für den einzelnen Hersteller mit erhöhtem Aufwand verbunden ist, wird von den betroffenen Kreisen nicht flächendeckend wahrgenommen. Der Beitrag analysiert Gründe hierfür und macht Vorschläge zu leichten Korrekturen in der inhaltlichen Ausrichtung der Normung. PY - 2013 SN - 2191-0073 VL - 3 IS - 7/8 SP - 22 EP - 27 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-29016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - German concept of break exclusion T2 - CENE (Atomaufsicht Brasillien) - Gesellschaft für Anlagen- und Reaktorsicherheit (GRS) mbH CY - Rio de Janeiro, Brazil DA - 2008-11-15 PY - 2008 AN - OPUS4-18775 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Brekow, Gerhard T1 - In-service inspection Atucha T2 - Meeting ARN, BAM, GRS, MPA Stuttgart CY - Buenos Aires, Argentina DA - 2011-03-15 PY - 2011 AN - OPUS4-23585 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Otremba, Frank T1 - Degradation of material properties significant for lifetime extension of nuclear power plants N2 - The discussion about the right energy sources or alternative energy generation goes around the world, mostly in connection with green-house gas reduction. Therefore, some countries have started to consider extending operation of nuclear power plants. This demands an extensive plant life management as well as the knowledge of the degradation in material properties. The Basis Safety Concept (BSC) in Germany observed this circumstance. Still, lifetime extension is not an issue in Germany due to phase out of nuclear energy. Part of the BSC is the application of non-destructive examination (NDE) methods from the beginning, i.e. from component manufacture, to the end of life. The application of a NDE method to detect and size defects in components in nuclear power plants is presented. Some material properties and their degradation during increase of operation time are also in the focus of this paper. KW - Plant life management KW - Material properties KW - Ageing effects KW - Lifetime extension KW - Leak before break behaviour KW - German safety basis concept KW - Nondestructive evaluation KW - Synthetic aperture focusing technique PY - 2010 SN - 0025-5300 VL - 52 IS - 1-2 SP - 11 EP - 19 PB - Hanser CY - München AN - OPUS4-20836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian A1 - Balke, Christian T1 - Performance of dangerous goods tanks in a fire T2 - ASME Intrnational Mechanical Congress and Exposition CY - Houston, TX, USA DA - 2012-11-09 PY - 2012 AN - OPUS4-27082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Blees, Christian A1 - Balke, Christian A1 - Otremba, Frank T1 - Plattenbrandprüfungen mit reaktiven Brandschutzbeschichtungen für Gastanks - Ein Vergleich zwischen Kleinprüfstand und 1-m³-Ofen N2 - In der Vergangenheit führte die Bundesanstalt für Materialforschung und -prüfung (BAM) zahlreiche Tankbrandversuche mit und ohne Sicherheitseinrichtungen durch. Dabei stellte sich heraus, dass Gastanks mit nicht ausreichend dimensionierten Sicherheitseinrichtungen bei einer äußeren thermischen Belastung innerhalb von 6 bis 10 min in Form eines BLEVE (Boiling Liquid Expanding Vapour Explosion) versagen können. Um die Feuerwiderstandsdauer eines Tanks zu erhöhen, besteht die Möglichkeit, den Tank u. a. mit einer sog. reaktiven Brandschutzbeschichtung zu versehen. Bei einer Temperatureinwirkung ab ca. 200 °C (produktabhängig) beginnt die Schicht aufgrund einer thermochemischen Reaktion aufzuschäumen. Die Tankwand wird dabei temporär vor einer weiteren schnellen Erwärmung geschützt. PY - 2012 SN - 2191-0073 VL - 2 IS - 1/2 SP - 27 EP - 30 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-25438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Gashochdruckleitungen T2 - Ruhrgas Meeting Gashochdruckleitungen CY - Essen, Germany DA - 2012-01-25 PY - 2012 AN - OPUS4-25415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Kühl, Christiane T1 - Sicherheitstechnische Anforderungen an Rohrfernleitungen in schutzwürdigen Gebieten T2 - Wangerooger Sicherheitstage 2012 Workshop: Vermeidung katastrophaler Umweltschäden - Schadensbegrenzung bei Dennoch/Exzeptionellen Störfällen CY - Wangerooge, Germany DA - 2012-04-22 PY - 2012 AN - OPUS4-25770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Kühl, Christiane T1 - Schadensbegrenzung bei Dennoch/Exzeptionellen Störfällen T2 - Wangerooger Sicherheitstage 2012, Vermeidung katastrophaler Umweltschäden CY - Wangerooge, Germany DA - 2012-04-22 PY - 2012 AN - OPUS4-25771 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reich, Franziska A1 - Otremba, Frank A1 - Würsig, Andreas T1 - Fail-safe? A study about the integrity of safety valves for tanks for dangerous goods N2 - In Europe, tanks designed on different safety philosophies are used for transporting one and the same liquid dangerous goods (Krautwurst, 2011). Owing to this circumstance, the BAM was commissioned by the BMVBS to conduct a research project designed to analyse and assess the equipment of tanks. Furthermore in these project were researched some failure mechanism of pressure relief devices (PRD). Based on the knowledge gained, possible solutions were worked out under safety-relevant aspects that would benefit tank transport by providing a lower hazard potential. Besides looking at the mode of operation and the construction of PRV, their blow-off characteristics and total flow rate are considered from a safety engineering point of view. Based on in-depth studies, a concept for and the further approach to examinations of the failure limits of PRD, especially of spring loaded relief valves, was developed and comprehensively described in the report “The use of safety devices, particularly safety valves, on transport containers” (Pötzsch, Reich, & Jochems, 2011). The purpose of this study was to investigate failure causes of safety valves by normal modes and accidental fire heat loads. A series of investigations for different influences using safety valves for tanks were obtained. Testing vibration modes and corrosion presents some design limits. Experimental study of a pressure vessel engulfing in fire identify significant design limits. The complete set of results provides direct information of fail-safe modes and discusses the usage. T2 - ASME 2013 International mechanical engineering congress and exposition CY - San Diego, CA, USA DA - 15.11.2013 KW - Safety valves KW - Transporttanks KW - Dangerous goods KW - Fire prooving KW - Response behavior PY - 2013 IS - IMECE2013-62204 SP - 1 EP - 5 AN - OPUS4-29717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Ziegenhorn, B. T. U. A1 - Sklorz, Christian T1 - Integrity of aluminium gas receptacle T2 - IMECE 2013 CY - San Diego, CA, USA DA - 2013-11-15 PY - 2013 AN - OPUS4-29668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian A1 - Balke, Christian T1 - Integrity of tanks under extreme loading conditions T2 - International Conference on Engineering and Applied Science CY - Hong Kong, China DA - 2013-12-19 PY - 2013 AN - OPUS4-29837 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sklorz, Christian A1 - Otremba, Frank A1 - Balke, Christian T1 - BLEVE performance of fire protection coating systems on dangerous goods tanks in a test fire N2 - How can the risk of a BLEVE be reduced? That is the main question based on different research projects. In various large scale fire tests fire protection coating systems were used of different manufacturers. The degree of the coating as well as the layer thickness and the processing were varied. These experimental configurations were partly tested with and without pressure relief valve. The pressure relief valves were not protected again the thermal Load from the test fire. The ambition is to find a minimum of the thickness from the fire protection coating witch delay a BLEVE up to 90 minutes. Here are given the most interested configurations of tanks in fire and a description of the test-rigs. KW - BLEVE KW - Fire protection coating KW - Isolation KW - Test rigs KW - Large scale fire test PY - 2013 DO - https://doi.org/10.12720/ijmse.1.2.90-93 SN - 2315-4527 VL - 1 IS - 2 SP - 90 EP - 93 PB - Engineering and technology publishing AN - OPUS4-30124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zur, Malte A1 - Klippel, Alexander A1 - Otremba, Frank A1 - Leder, A. T1 - Numerical simulation and experimental study of cabin-airflow and transport of gas-mixtures in aircraft cargo compartments: model validation N2 - Dangerous goods are transported as air freight in commercial aircrafts. Using plastic jerrycans or plastic containers, liquids or gases can escape by leakage or permeation effects. Prior research by the German Federal Institute for Materials Research and Testing (BAM) showed that the lower explosion limit can be reached when transporting dangerous goods in sea-freight containers under normal transportation situations. This motivated the presented study of the transportation situation of dangerous goods in cargo compartments of commercial airplanes. The scope of this paper is to present the experimental method used for validating a numerical model for CFD (Computational Fluid Dynamics) simulations. The CFD model will be used in a future study to evaluate the potential risk from transporting dangerous goods. The objective of this paper is to present the model mock-up of an aircraft cargo compartment and some examples of three dimensional velocity profiles of the air flow in the mock-up. The velocity profiles are calculated using numerical simulations and measured by Laser-Doppler-Anemometry (LDA) experiments. The mock-up is a generic model of a wide-body aircraft lower deck cargo compartment in a 1:10 scale. Geometry, air exchange rates and inlet as well as outlet flow conditions in the cargo compartment are modeled using realistic boundary conditions. The commercial CFD (Computational Fluid Dynamics) code ANSYS CFX 14 is used for numerical flow simulations applying RANS (Reynolds-Averaged-Navier-Stokes) equations and turbulence models. The turbulence models studied are the renormalization group k-ε-model (RNG), the Reynolds-Stress model by Launder, Reece and Rodi (LRR) and the SST-k-ω-model by Menter (SST). The flow measurement with LDA in the mock-up of a cargo compartment proves to be a feasible method for producing data to validate CFD simulations. Qualitative evaluation of the results shows a good overall agreement between numerical and experimental results. The experimental validation indicates that the implemented CFD model is capable of reproducing the flow situation in the model mock-up. T2 - ASME 2013 Fluids engineering summer meeting - 7th International symposium on flow applications in aerospace CY - Incline Village, Nevada, USA DA - 07.07.2013 KW - Computational fluid dynamics KW - Aircraft cabin air flow KW - Gas mixtures KW - Model validation PY - 2013 SN - 978-0-7918-5555-3 IS - Paper FEDSM2013-16622 SP - 1 EP - 9 AN - OPUS4-30076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Otremba, Frank A1 - Mohr, F. A1 - Kilian, R. T1 - Alloy 800 steam generator tube stress corrosion cracks - Detection T2 - 9th International conference on NDE in relation to structural integrity for nuclear and pressurized components CY - Seattle, USA DA - 2012-05-22 PY - 2013 SN - 978-92-79-28212-6 DO - https://doi.org/10.2790/74243 SN - 1018-5593 SP - 862 EP - 870 AN - OPUS4-28886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hurtado-Hurtado, G. A1 - Morales-Velazquez, L. A1 - Valtierra-Rodríguez, M. A1 - Otremba, Frank A1 - Jáuregui-Correa, J. C. T1 - Frequency Analysis of the Railway Track under Loads Caused by the Hunting Phenomenon N2 - Hunting is a potentially dangerous phenomenon related to the lateral oscillation of the wheels that impacts the rails and causes the wear of the infrastructure’s components. Therefore, the analysis and timely detection of hunting can lead to the application of corrective maintenance tasks, reducing damages, and costs and even derailments as a result. In this work, the vibration response of a finite element model of a rail with hunting-induced loads by a single wheel is analyzed in three directions: longitudinal, lateral, and vertical. The contact patch forces are calculated by means of Simpack® using the Kalker linear theory and the contact Hertz theory. The system is solved by using the Newmark-_ approach. The results of the deflection and vibration analysis, following the proposed methodology, show how the different characteristics of the loads impact the rail. KW - Continuous wavelet transform KW - Empirical mode decomposition KW - Finite element method KW - Frequency analysis KW - Hunting phenomenon KW - Mechanical modelling KW - Rail vibrations PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-551517 UR - https://www.mdpi.com/2227-7390/10/13/2286/htm# DO - https://doi.org/10.3390/math10132286 VL - 10 IS - 13 SP - 1 EP - 17 PB - MDPI AN - OPUS4-55151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero Navarrete, J. A. T1 - Experimental Assessing of the Energy Transformation in Turns N2 - Turning maneuvers of rail vehicles involve demanding situations for the infrastructure because of the steering forces generated and the resultant lateral load transfers. Such forcing situation involves increased tangential forces that consume kinetic energy from the vehicle. While much attention has been paid in the literature to the damage in such infrastructure segments, the energy that is dissipated in these maneuvers, has not been explicitly addressed. In this paper, a specialized scale-down infrastructure is used to characterize the effect of the initial speed of the vehicle and its mass, on the magnitude of both the rail forces developed and the amount of dissipated energy during turning maneuvers. The outputs of the experiments suggest that most of the original kinetic energy is dissipated at the first portion of the turn. Also, that the magnitude of the wheel forces and the amount of dissipated energy, correlate. That is, a greater rail damage would correspond to greater energy dissipation. T2 - IMECE2022 CY - Columbus, OH, USA DA - 30.10.2022 KW - Energy dissipation KW - Turning maneuvers KW - Rail damage KW - Experimental approaches PY - 2022 AN - OPUS4-56333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero Navarrete, J. A. T1 - Experimental Assessing of the Energy Transformation in Turns N2 - Turning maneuvers of rail vehicles involve demanding situations for the infrastructure because of the steering forces generated and the resultant lateral load transfers. Such forcing situation involves increased tangential forces that consume kinetic energy from the vehicle. While much attention has been paid in the literature to the damage in such infrastructure segments, the energy that is dissipated in these maneuvers, has not been explicitly addressed. In this paper, a specialized scale-down infrastructure is used to characterize the effect of the initial speed of the vehicle and its mass, on the magnitude of both the rail forces developed and the amount of dissipated energy during turning maneuvers. The outputs of the experiments suggest that most of the original kinetic energy is dissipated at the first portion of the turn. Also, that the magnitude of the wheel forces and the amount of dissipated energy, correlate. That is, a greater rail damage would correspond to greater energy dissipation. T2 - IMECE2022 CY - Columbus, OH, USA DA - 30.10.2022 KW - Turning maneuvers KW - Energy dissipation KW - Rail damage KW - Experimental approaches PY - 2022 SP - 1 EP - 6 AN - OPUS4-56334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank ED - Zobory, I. T1 - Conceptual design of an active centre plate N2 - The efficiency and safety of railway transportation depend both on numerous factors linked to the vehicle, the infrastructure, the operator and the environment. Curved tracks are subjected to demanding situations due to elevated stress levels, as a function of the operating conditions and vehicle/infrastructure design. In such segments, steering forces are superimposed to lateral load transfers. The steering forces depend on the condition and the design of the centre plate and bogies’ suspensions design. While the friction at the centre plate provides the needed damping to mitigate the hunting vibration of the bogie in straight track segments, such yaw resistance originates high steering forces and rail damage on curved tracks. A centre plate with low friction at turns and high friction at straight track segments would thus be highly advantageous. In this paper, a centre plate design is proposed which provides a yaw-rotation resistance torque that depends on the bogie-car relative position. Two different designs are considered for that purpose, one that combines a spring-acted centring mechanism with a lower pair kinematics, while the other one involves higher kinematic pairs which should incorporate lateral damping elements. As a result of using an engineering design approach, the higher kinematic pairs-based design is recommended however, the validation of such operational principles, including the introduction of the needed damping, should be configured on the basis of experimental models. T2 - 11th International Conference on Railway Bogies and Running Gears CY - Budapest, Hungary DA - 09.09.2019 KW - Steering torques KW - Railway transportation KW - Bogie design KW - Conceptual design KW - Engineering design KW - Transport externalities PY - 2020 SN - 978-963-9058-42-2 SP - 77 EP - 86 PB - Scientific Society of Mechanical Engineers (SSME/GTE) CY - Budapest AN - OPUS4-54086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Romero-Navarrete, José A. A1 - Hurtado-Hurtado, G. T1 - Determination of the effect of sloshing on the railcar-track dynamic behavior N2 - Liquid cargo has a significant impact on the interface wheel-track interaction. The sloshing affects the track-railcar's dynamic behavior. The effect is detectable at the track level and at the vehicle. Its characterization requires the combination of different techniques: Empirical Mode Decomposition (EMD) Time-Frequency Maps Sloshing occurred when significant perturbations happened in the railcar: The railcar entered a curve Reduction in its travel speed A railcar with a tank is a clear example of a multibody dynamic system with a nonlinear behavior. T2 - 7th International Symposium on Multibody Systems and Mechatronics - MuSMe 2021 CY - Córdoba, Argentina DA - 12.10.2021 KW - Liquid cargo KW - Wheel-track interaction KW - Sloshing affects KW - Vehicle PY - 2021 AN - OPUS4-53572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Romero-Navarrete, José A. A1 - Hurtado-Hurtado, G. ED - Pucheta, M. ED - Cardona, A. ED - Preidikman, S. ED - Hecker, R. T1 - Determination of the Effect of Sloshing on the Railcar-Track Dynamic Behavior N2 - This paper presents the study of the impact caused by a liquid Cargo on a railway infrastructure. The dynamic behavior of a tank car corresponds to a multibody dynamic system with several degrees of freedom. This study’s data were obtained from a scale experimental fixture consisting of a track and a railcar with a tank. The track was instrumented with strain gauges and the railcar with accelerometers. The data showed non-periodic and periodic terms; therefore, the results were analyzed with the Empirical Mode Decomposition method (EMD). It was found that the EMD identified the signal components that were related to the sloshing. These components represent the mode shapes of the original signal. The location of the sloshing in the track was found applying spectrograms to the accelerometer data. This paper’s experimental outputs suggest that the sloshing effect is detectable at the track and in the vehicle dynamics. KW - Sloshing effect KW - Empirical Mode Decomposition KW - Wheel/track interaction KW - Multibody dynamics PY - 2021 SN - 978-3-030-88750-6 DO - https://doi.org/10.1007/978-3-030-88751-3_14 SP - 131 EP - 140 PB - Springer Nature Switzerland AG AN - OPUS4-53561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Würsig, Andreas A1 - Otremba, Frank T1 - Neue FVK-Tanks in den Unmodellvorschriften sowie Ergebnisse aktueller Forschungsvorhaben N2 - 100 mm of PUR-foam give satisfying results in terms of thermal properties. The non-pressure testing methods gives reliable and repeatable results. Bending modulus of laminates does not change until the first damage occurs. After that, the bending modulus decreases by 50 % but max. stress is still higher than at room temperature. T2 - 25. Gefahrgutkongress MV CY - Rostock, Germany DA - 19.10.2021 KW - FVK-Tanks KW - Unmodellvorschriften KW - Forschungsvorhaben PY - 2021 AN - OPUS4-53570 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan A1 - Kutz, P. W. A1 - Otremba, Frank T1 - Testing of Small Scale Tank Prototypes under Cryogenic Conditions N2 - Climate change, CO2 reduction, resource efficiency are only 3 current keywords that describe the current industrial-economic situation. In order to influence climate change effectively, the conversion of supply systems with technically usable forms of energy must succeed in the next decade. The international network founded in Baku in 2015 bundles research activities in the broad field of energy supply and energy efficiency. Discuss current research approaches and results with scientists and experts from renowned universities and follow Azerbaijan's efforts to implement the energy revolution. T2 - Neseff 2020 CY - Online meeting DA - 28.09.2020 KW - Mud pumps KW - Mud circulation system KW - Pistons KW - Hydrostatic pressure KW - Friction wear KW - Ceramic liners KW - Tribology PY - 2020 SN - 978-3-940471-59-8 SP - 4 EP - 9 AN - OPUS4-52149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero Navarrete, J. A. A1 - Otremba, Frank A1 - Lozano Guzmán, A. A. T1 - Experimental-theoretical modelling of the lateral sloshing in rail tankers N2 - The objective of this paper is to describe and to validate a simplified pendulum-analogy model to simulate the interaction of a liquid cargo with ist carrying vehicle. The resulting testing rig consists of a rectangular container, spring supported on a two wheelset-bogie having a scale down of 1/10 with respect to a full-size equipment. The testing rig is used to validate a simple pendulum-based, simplified three degree-of-freedom mathematical model of the response of a partially filled container to lateral accelerations. The length of the pendulum is set according to validated methodologies. The resulting mathematical scheme reveals a high correlation with the experimental output, on the order of 99%, while some other performance measures, related to the peak forces and the range of variation of the wheel-rail forces, also show good concordance with the experimental results. KW - Sloshing KW - Rail tankers KW - Pendulum analogy KW - Experimental modelling KW - Mechanical fatigue PY - 2021 DO - https://doi.org/10.1504/ijhvs.2021.117504 VL - 28 IS - 3 SP - 435 EP - 454 AN - OPUS4-53101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. A1 - Romero-Navarrete, J. A. T1 - Experimental test rig for simulating dynamic loads on subway systems N2 - Scaled-down experimental facility: Can reproduce actual failures; can produce simulated data for identifying cracks in the substructure or other defects. The acceleration data can be converted into an equivalent deformation. The experimental facility can analyse dynamic loads. Equivalent force data: Facilitates the application to a health monitoring system; simplifies the development of predictive maintenance. These data is helpful in validating analytical or simulation models. T2 - Fifth International Conference on Railway Technology CY - Montpellier, France DA - 22.08.2022 KW - Test rig KW - Dynamic loads KW - Subway system PY - 2020 SP - 1 EP - 6 AN - OPUS4-55566 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. A1 - Romero-Navarrete, J. A. T1 - Experimental test rig for simulating dynamic loads on subway systems N2 - Degradation in substructures, Mexico’s City Subway. Improve predictions using vibration Measurements. Ability to test operating conditions at Laboratory. Improve previous laboratory rig. Control operating conditions. Produce enough data for evaluating actual conditions. T2 - Fifth International Conference on Railway Technology CY - Montpellier, France DA - 22.08.2022 KW - Test rig KW - Simulating KW - Dynamic loads KW - Subway PY - 2022 AN - OPUS4-55568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Romero Navarrete, J. A. A1 - Otremba, Frank A1 - Lozano Guzmán, A. A. T1 - Liquid cargo effect on load transfer under orthogonal accelerations N2 - A methodology is proposed for the experimental analysis of the liquid cargo effect under combined orthogonal accelerations. To simultaneously subject the vehicle-cargo system to longitudinal and lateral accelerations, the vehicle is set obliquely on a tilt table. The experimental outputs suggest that there is a significant effect of the liquid cargo on the lateral load transfer ratio (LTR), on the order of 20%, which is attributable to the resulting shifting of the liquid cargo’s centre of gravity. That is, the peak LTR values due exclusively to sloshing were not significant, in such a way that the liquid cargo would only pose a safety risk under a steady acceleration input. Also, the inverse of the product of the magnitude of the acceleration times the free surface length, correlates with the liquid cargo effect. That is, the magnitude of the input acceleration is not fully determinant for greater load transfers. KW - Sloshing KW - Liquid cargo KW - Cargo shifting KW - Lateral load transfer KW - Braking in a turn manoeuvre KW - Experimental methods KW - Transport safety PY - 2022 DO - https://doi.org/10.1504/ijhvs.2022.127011 SN - 1744-232X VL - 29 IS - 3 SP - 213 EP - 226 PB - Inderscience Enterprises CY - Geneva AN - OPUS4-56016 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jauregui-Correa, J. C. A1 - Morales-Velazquez, L. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. T1 - Method for predicting dynamic loads for a health monitoring system for subway tracks N2 - This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method. The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data. KW - Health monitoring KW - Transfer function KW - Railroad KW - Substructure failures KW - Dynamic loads PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557480 DO - https://doi.org/10.3389/fmech.2022.858424 SN - 2297-3079 VL - 8 SP - 1 EP - 16 PB - Frontiers Media CY - Lausanne AN - OPUS4-55748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Iancu, O.T. A1 - Erhard, Anton A1 - Otremba, Frank A1 - Sklorz, Christian T1 - Consistency between analytical and finite element predictions for safety of cylindrical pressure vessels at higher temperatures N2 - Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt. KW - Materials testing KW - FEM KW - Plastic instability KW - Limit load analysis KW - Pressure vessel KW - Analytical solution PY - 2014 SN - 0025-5300 VL - 56 IS - 4 SP - 274 EP - 278 PB - Hanser CY - München AN - OPUS4-30722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - ACEAIT-2673 Heat Treatment of Aluminium Receptacle T2 - ACEAIT Annual Conference on Engineering and Information Technology CY - Tokyo, Japan DA - 2014-03-28 PY - 2014 AN - OPUS4-30511 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian A1 - Iancu, A1 - Balke, Christian T1 - Consistency between analytical and Finite element predictions for safety analysis of cylindrical pressure vessels at higher temperatures T2 - ASME IMECE2014-36107 CY - Montreal, Canada DA - 2014-11-16 PY - 2014 AN - OPUS4-32046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Reich, Franziska A1 - Sklorz, Christian A1 - Balke, Christian T1 - Limited load analysis of pressurized containers T2 - ASME IMECE2014-36334 CY - Montreal DA - 2014-11-16 PY - 2014 AN - OPUS4-32048 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - BLEVE - Untersuchungen am Transporttank T2 - Sichrheitstage Wangerooge 2014 CY - Wangerooge, Germany DA - 2014-05-12 PY - 2014 AN - OPUS4-31024 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Otremba, Frank T1 - Nondestructive testing and fracture mechanics N2 - Nondestructive Testing (NDT) and fracture mechanics are two different disciplines in applied engineering science. Both areas are very important for the evaluation of the component integrity. Unfortunately the technical understanding in both disciplines is not identically, what lead to misunderstandings. In the present paper, the basic ideas about fracture mechanics and the input parameters coming from the NDT side are explained, concerning the integrity evaluation of the components. The widely used NDT methods are magnetic particle, dye penetrant, electrical eddy currents, radiography and ultrasonics. But not all of these common NDT methods can deliver parameters satisfy the fracture mechanics requirements. The first two can detect only surface-breaking or immediately sub-surface defects. Eddy current can also find defects in deeper sub-surface layers, while radiography and ultrasonics can also find embedded, remote defects. These three methods have furthermore a high potential for defect sizing and are therefore predestined to provide fracture mechanics input parameters. At the example of steam generator tube inspection the interplay of eddy current and fracture mechanics as related to tube integrity will be explained. T2 - 5th International CANDU In-Service inspection workshop and NDT in Canada 2014 conference CY - Toronto, Ontario, Canada DA - 16.06.2014 KW - Eddy current KW - Steam generator tube inspection KW - Component integrity KW - Fracture mechanics PY - 2014 SP - 1 EP - 12 AN - OPUS4-30907 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - PALESTRA - Pre-warning system of tanks containing dangerous goods T2 - 4. FORUM SOBRE NOVAS TECNOLOGIAS E APLICACOES DE END E INSPECÄO CY - Rio de Janeiro, Brazil DA - 2014-04-28 PY - 2014 AN - OPUS4-30645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Borch, Jörg-Peter A1 - Birk, T1 - Pressure Vessel Fire Test T2 - ISO TC 92 SC2 WG 12 CY - Brussels, Belgium DA - 2014-09-17 PY - 2014 AN - OPUS4-31417 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -