TY - RPRT A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Erfassung der Zahl feiner und ultrafeiner Partikel aus Bürogeräten während der Druckphase zur Entwicklung eines Prüfverfahrens für das Umweltzeichen Blauer Engel für Bürogeräte mit Druckfunktion KW - Bürogeräte KW - Laserdrucker KW - Partikelemissionen PY - 2013 UR - http://www.umweltbundesamt.de/publikationen/erfassung-zahl-feiner-ultrafeiner-partikel-aus SN - 1862-4804 VL - 74 IS - FKZ/Projektnr. 3708 95 301 UBA-FBNr. 001743 SP - 1-146, Anh. 1-39 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-28988 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kemmlein, Sabine A1 - Hahn, Oliver A1 - Jann, Oliver A1 - Kalus, Sabine A1 - Stolle, Dirk ED - Levin, H. T1 - Emission of Flame Retardants from Consumer Products and Building Materials N2 - The emission levels of high boiling brominated (BFR) and phosphoric (POC) flame retardants (FR) in different materials were examined. For the determination of the emission rate the tests were done in different emission test chambers and cells under standard conditions (23 C, 50% RH and fixed area specific air flow rates). Selected products, e.g. printed circuit boards, were investigated at elevated temperature (e.g. 60 C) to simulate working conditions. Applied analytical techniques for the air samples adsorbed on polyurethane foam (PUF) are soxhlet and ultrasonic extraction. Different conditions were used to analyse the FR via GC-MS. Based on the first results it could be demonstrated that the emission depends on material density and surface condition. The concentrations over time obtained for tris(3-chloropropyl)-phosphate, e.g., from emission test chamber and cell show a good correlation, partly the measured concentration are different. Sampling at elevated temperature gives higher concentrations. T2 - 9th International Conference on Indoor Air Quality and Climate CY - Monterey, CA, USA DA - 2002-06-30 KW - Flame retardants KW - SVOC/POM KW - Material emission KW - Measurement methods PY - 2002 SN - 0-9721832-0-5 VL - 2 SP - 920 EP - 925 PB - International Academy of Indoor Air Sciences CY - Santa Cruz, Calif. AN - OPUS4-2001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Erfassung der Zahl feiner und ultrafeiner Partikel aus Bürogeräten während der Druckphase zur Entwicklung eines Prüfverfahrens für das Umweltzeichen Blauer Engel für Bürogeräte mit Druckfunktion (UFOPLAN 370895301) N2 - Das diesem Bericht zugrundeliegende Forschungsvorhaben konzentriert sich auf die Erfassung partikulärer Emissionen im Fein- und Ultrafeinstaubbereich aus Bürogeräten mit Laserdruckfunktion. Vor dem Hintergrund einer öffentlichen Diskussion über mögliche, mit diesen Emissionen verbundene Gefahren wurde die BAM vom ⁠UBA⁠ damit beauftragt, eine Messmethode für diese Emissionen zu entwickeln, die bestehende Vergabegrundlage für das Umweltzeichen „Blauer Engel“ um den Aspekt Partikelemission zu erweitern und die partikulären Emissionen physikalisch und chemisch zu analysieren. Eine daraus resultierende Vergabegrundlage wird dem RAL zur Vorbereitung einer Expertenanhörung mit den interessierten Kreisen in diesem Jahr vorgelegt werden. KW - Bürogeräte mit Laserdruckfunktion KW - Feine und ultrafeine Partikel KW - Chemische Emissionen KW - Blauer Engel PY - 2013 UR - http://www.umweltbundesamt.de/publikationen/erfassung-zahl-feiner-ultrafeiner-partikel-aus SN - 1862-4804 SN - 0722-186X IS - 74 SP - 1 EP - 189 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-27523 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kemmlein, Sabine A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Emission of Flame Retardants from Consumer Products and Building Materials (Research Report 299 65 321 / UBA-FB 00,475) N2 - Various insulating boards, assembly foams, PC-systems, upholstery and a mattress were examined for possible emissions of polybrominated and organophosphorus flame retardants. 0.02 m3- and 1m3- emission test chambers and 1Llitre cells were used to perform the investigations. The substances of interest are mainly classified as SVOC. A sampling technique using polyurethane foam plugs and special analytical methods was developed. The PUF-plugs were extracted by ultrasonic and soxhlet extraction and the extracts were concentrated. The analyses were performed by GC/MS and HPLC/DAD. Chamber measurements were generally taken over 28 days, but in the case of SVOC, a test period of a minimum of 100 days was necessary to achieve equilibrium. The determination of most of OPCs was successful using emission test chambers. Due to sink effects the determination of low volatile OPC such as RDP and BDP needs to be improved. Brominated flame retardants are quantifiable up to hexabrominated compounds using emission test chambers as a reference method. The emission of lower volatile compounds, e.g. HBCD, was strongly affected by sink effects. Emission of decaBDE was not quantifiable at all. Based on the results presented further investigations are required for an adequate risk assessment of flame retarded products and their contribution to the contamination of the indoor air environment. TCPP was found to be one of the most commonly used organophosphorus flame retardants in polyurethane foam applications. Depending on the sample type 0.012 to 140 µg m-2 h-1 was obtained for area-specific emission rates (SERa) for TCPP. PBDEs, for example, exhibited product-specific emission rates (SERu) between 0.1 and 14.2 ng unit-1 h-1 and SERa between 0.2 and 6.6 ng m-2 h-1. More data about the emission behaviour of FR are required with special regard to substance migration, aging and long-term emission in particular. KW - Emission KW - Semi volatile organic compounds (SVOC) KW - Polybrominated flame retardants KW - Organophosphorus flame retardants PY - 2003 UR - http://www.umweltbundesamt.de/publikationen/emission-of-flame-retardants-from-consumer-products SP - 1 EP - 188 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-11186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kemmlein, Sabine A1 - Hahn, Oliver A1 - Jann, Oliver ED - Schartel, Bernhard T1 - Investigations on emissions of selected flame retardants. A possible route of exposure? T2 - 10th European meeting on fire retardancy and protection of materials/European conference on fire retardant polymers CY - Berlin, Germany DA - 2005-09-07 KW - Emission test chamber KW - Polybrominated flame retardants KW - Organophosphates PY - 2005 SN - 978-3-8334-8873-3 SP - 11_0_1 PB - Books on Demand GmbH CY - Norderstedt AN - OPUS4-10852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kemmlein, Sabine A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Suitability of emission test chambers and cells for measuring organophosphates and brominated flame retardants from insulation material T2 - Indoor Air 2005 CY - Beijing, PR China DA - 2005-09-04 KW - Emission measurements KW - Brominated flame retardants KW - Organophosphates PY - 2005 SN - 7-89494-830-6 VL - II IS - 2 SP - 2325 EP - 2328 PB - Tsinghua University Press CY - Beijing AN - OPUS4-10849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Horn, Wolfgang A1 - Hahn, Oliver A1 - Jann, Oliver A1 - Kalus, Sabine ED - Wai, T. K. ED - Sekhar, C. ED - Cheong, D. T1 - Do particleboards produced with recycled wood contribute to indoor air pollution with biocides? T2 - 7th Healthy Buildings Conference ; HB 2003 ; ISIAQ international conference CY - Singapore, Republic of Singapore DA - 2003-12-07 KW - SVOC KW - Biocide KW - Chamber study KW - Material emission KW - Wood PY - 2003 SN - 981-049974-4 VL - 1 SP - 367 EP - 372 CY - Singapore AN - OPUS4-3419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hahn, Oliver A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Luftschadstoffe in Archiven und Museen - Wie können Kunstwerke vor einer übermäßigen Belastung geschützt werden? KW - Luftschadstoffe KW - VOC KW - Emissionsmessungen KW - Schutz vor Kunst- und Kulturgut PY - 2004 SN - 0933-4017 VL - 110 IS - 6 SP - 406 EP - 410 PB - Callwey CY - München AN - OPUS4-4116 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Beckhoff, B. A1 - Hahn, Oliver A1 - Weser, J. A1 - Wilke, M. A1 - Ulm, G. A1 - Jann, Oliver T1 - Environmental Analyses by TXRF - NEXAFS and IR-Spectroscopy: Speciation of Br in Organics and Characterization of the Organic Matrix KW - TXRF-NEXAFS KW - FTIR KW - Environmental analyses PY - 2006 UR - http://www.helmholtz-berlin.de/media/media/oea/web/pr_webseite/druckschriften/berichte/bessy/annualreport2005.pdf#page=30 SN - 0179-4159 SP - 28 EP - 30 PB - Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung CY - Berlin AN - OPUS4-12410 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barthel, Mathias A1 - Pedan, Vasilisa A1 - Hahn, Oliver A1 - Rothhardt, Monika A1 - Bresch, Harald A1 - Jann, Oliver A1 - Seeger, Stefan T1 - XRF-Analysis of fine and ultrafine particles emitted from laser printing devices N2 - In this work, the elemental composition of fine and ultrafine particles emitted by ten different laser printing devices (LPD) is examined. The particle number concentration time series was measured as well as the particle size distributions. In parallel, emitted particles were size-selectively sampled with a cascade impactor and subsequently analyzed by the means of XRF. In order to identify potential sources for the aerosol's elemental composition, materials involved in the printing process such as toner, paper, and structural components of the printer were also analyzed. While the majority of particle emissions from laser printers are known to consist of recondensated semi volatile organic compounds, elemental analysis identifies Si, S, Cl, Ca, Ti, Cr, and Fe as well as traces of Ni and Zn in different size fractions of the aerosols. These elements can mainly be assigned to contributions from toner and paper. The detection of elements that are likely to be present in inorganic compounds is in good agreement with the measurement of nonvolatile particles. Quantitative measurements of solid particles at 400 °C resulted in residues of 1.6 × 109 and 1.5 × 1010 particles per print job, representing fractions of 0.2% and 1.9% of the total number of emitted particles at room temperature. In combination with the XRF results it is concluded that solid inorganic particles contribute to LPD emissions in measurable quantities. Furthermore, for the first time Br was detected in significant concentrations in the aerosol emitted from two LPD. The analysis of several possible sources identified the plastic housings of the fuser units as main sources due to substantial Br concentrations related to brominated flame retardants. KW - Particulate emissions KW - UFP KW - FP KW - Laser printers KW - XRF PY - 2011 DO - https://doi.org/10.1021/es201590q SN - 0013-936X SN - 1520-5851 VL - 45 IS - 18 SP - 7819 EP - 7825 PB - ACS Publ. CY - Washington, DC AN - OPUS4-24393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Farke, M. A1 - Hahn, Oliver T1 - Assessment of emissions from materials for museum equipment N2 - Museums worldwide are equipped with different display cases. Exhibit display cases should protect cultural objects from dust as well as from mechanical and physical damage. To ensure a stable climate inside the display cases, a low air exchange rate is maintained. Typically air exchange rates are often smaller than 0.1 d'1 (Torge, 2000), which can result in rising concentrations of potential harmful immissions inside of the display cases due to emissions from materials. Especially high concentrations of organic acids, which can emit from e.g. sealing materials, can produce damage of cultural objects, as shown in Figure 1. To minimize such risks emissions must be reduced. T2 - Healthy Buildings 2012 - 10th International conference CY - Brisbane, Australia DA - 08.07.2012 KW - Assessment of emissions from materials for museum equipment KW - BEMMA display case KW - Protection of cultural object KW - Emissions PY - 2012 SN - 978-1-921897-40-5 SP - 1 EP - 2 (7G.3) AN - OPUS4-27525 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiegner, Katharina A1 - Farke, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Hahn, Oliver T1 - Den Schadstoffen auf der Spur - Die Bewertung von Emissionen aus Materialien für Museumsausstattungen mithilfe des neuen BEMMA-Schemas N2 - Ausstellungskuratoren, Restauratoren oder Fachplaner stehen immer wieder vor der Entscheidung, geeignete Materialien für Museumsausstattungen auswählen zu müssen. Vitrinen, Depoteinrichtungen, aber auch Transportverpackungen für Kunst- und Kulturgut sollten unbedingt frei von Schadstoffen sein. Ein neues Verfahren ermöglicht nun eine problemorientierte Untersuchung und Bewertung von Materialien mit belastbaren und reproduzierbaren Ergebnissen. KW - BEMMA KW - Emissionsarme Vitrine KW - Schadstoffe PY - 2012 SN - 0933-4017 VL - 3 SP - 38 EP - 44 PB - Callwey CY - München AN - OPUS4-25794 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kemmlein, Sabine A1 - Hahn, Oliver A1 - Jann, Oliver A1 - Kalus, Sabine A1 - Stolle, Dirk ED - Wai, T. K. ED - Sekhar, C. ED - Cheong, D. T1 - Emission of phosphorus organic and polybrominated flame retardants from consumer products and building materials T2 - 7th Healthy Buildings Conference ; HB 2003 ; ISIAQ international conference CY - Singapore, Republic of Singapore DA - 2003-12-07 KW - Flame retardants KW - SVOC/POM KW - Material emission PY - 2003 SN - 981-049974-4 VL - 1 SP - 142 EP - 147 CY - Singapore AN - OPUS4-7066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wiegner, Katharina A1 - Farke, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Hahn, Oliver ED - Brozio, P. T1 - Schadstoffe im Museum richtig einschätzen N2 - Schadstoffe beschäftigen derzeit Museen weltweit Heute weiß man, dass diese auch aus Materialien, die für den Ausstellungsbau verwendet werden, austreten können, was eine Gefahr für Exponate darstellt. Ein neues Verfahren namens BEMMA bietet nun erstmalig die Möglichkeit, relativ schnell und effektiv eine problemorientierte Untersuchung und Bewertung mit belastbaren und reproduzierbaren Ergebnissen vorzunehmen. KW - Emissionsarme Vitrinen KW - Präventive Konservierung KW - VOC KW - BEMMA PY - 2011 SN - 978-3-7667-1962-1 SP - 127 EP - 131 PB - Callwey CY - München AN - OPUS4-25377 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Erfassung der Zahl feiner und ultrafeiner Partikel aus Bürogeräten während der Druckphase zur Entwicklung eines Prüfverfahrens für das Umweltzeichen Blauer Engel für Bürogeräte mit Druckfunktion - Zusammenfassung N2 - Vor dem Hintergrund der anhaltenden öffentlichen Diskussion um mögliche gesundheitliche Risiken von Ultrafein- und Feinstaubemissionen aus Bürogeräten mit Laserdruckfunktion (LPD, Laser Printing Device) wurde vom Umweltbundesamt ein Forschungsvorhaben zur Entwicklung einer Prüfprozedur für die Quantifizierung der emittierten Partikel durch Zählung unter Standardbedingungen in Emissionsmesskammern, sowie zur physikalischen und chemischen Charakterisierung dieser Aerosole initiiert. Als Ergebnis konnte die Partikelzählung in den Entwurf des Prüfverfahrens für die Bestimmung von Emissionen (RAL-UZ-122, Anhang S-M) des Umweltzeichens "Blauer Engel" für Bürogeräte sowie in den Prüfstandards ECMA-328 und den Entwurf der ISO/IEC 28360 integriert werden. Die Methode wurde in einem internationalen Ringversuch erfolgreich getestet. Auf dieser Basis können Vergabekriterien und -werte für die Emission von Fein- und Ultrafeinpartikeln im Rahmen der Vergabe des Umweltzeichens Blauer Engel vereinbart und Produktprüfungen vorgenommen werden. KW - Blauer Engel KW - Bürogeräte mit Druckfunktion KW - Partikelemission KW - RAL-UZ 122 PY - 2011 VL - Förderkennzeichen UFOPLAN 3708 95 301 SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59863 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Kunstgüter in Vitrinen: was helfen Materialuntersuchungen gemäß BEMMA-Schema? N2 - Moderne Vitrinen sollen gleichzeitig eine hohe Dichtigkeit und die Abwesenheit jeglicher Fremdstoffe in den Vitrinen gewährleisten. Diese Anforderungen sind zeitgleich kaum erfüllbar, da es emissionsfreie Materialien (vor allem Kleb- und Beschichtungsstoffe) nicht gibt. Um die potentiellen Emissionen zu minimieren wurde ein Messverfahren entwickelt, welches inzwischen als BEMMA-Schema (Bewertung von Emissionen aus Materialien für Museumsausstattungen) in die Museumswelt Einzug genommen hat. Die erfolgreiche Bewertung der für den Bau verwendeten Materialien gemäß BEMMA-Schema resultiert nicht in einer emissionsfreien Vitrine, sondern soll bei der Auswahl geeigneter Materialien zur Herstellung möglichst emissionsarmer Vitrinen helfen. Konkrete handwerkliche Durchführungen beim Bau, Dichtheits¬anforderungen, wie auch die Aufstellbedingungen (Umgebung der Vitrine) beeinflussen die Emissionscharakteristik der fertigen Vitrine in der Praxis. Eine saubere Vitrine hilft nichts in einer belasteten Umgebung oder auch bei emittierenden Exponaten. Inzwischen liegen Erfahrungen mit dem Schema seit 2012 vor. Der Messablauf sieht vor, dass von den Materialien kleine Muster mit der Mikrokammer (Markes) innerhalb von 2 Tagen untersucht werden. Dabei wird mit Silikagelkartuschen auf Ameisen- und Essigsäure, mit DNPH auf Aldehyde und Ketone und mit Tenax® sowohl auf VOC als auch für die spezifische Oxim-Analytik die Abluft der Mikrokammern untersucht. Die Bewertungskriterien basieren auf den Ergebnissen einer Vorstudie mit ca. 150 verschiedenen Produkten im Zeitraum 2010 bis 2012. T2 - 12. Fachkongress der Arbeitsgemeinschaft ökologischer Forschungsinstiute (AGÖF) CY - Hallstadt (Bamberg), Germany DA - 17.10.2019 KW - Museum KW - Emission KW - Bauprodukte KW - BEMMA KW - Vitrinen PY - 2019 SN - 978-3-930576-11-1 VL - 12. Fachkongress SP - 245 EP - 249 PB - Arbeitsgemeinschaft ökologischer Forschungsinstiute (AGÖF) e. V. CY - Springe-Eldagsen AN - OPUS4-49326 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiegner, Katharina A1 - Hahn, Oliver A1 - Horn, Wolfgang A1 - Farke, M. A1 - Kalus, Sabine A1 - Nohr, Michael A1 - Jann, Oliver T1 - Determination of formic and acetic acid emissions in indoor air or from building products N2 - Several construction and building materials, including wood, glue and coatings, are possible sources of very volatile organic compounds (VVOCs) and volatile organic compounds (VOCs) like formic and acetic acid. Due to very high air tightness and very low air exchange rates in new buildings concentrations of these harmful substances can increase considerably. To minimize the risk, emissions from building products should be identified and quantified. With the common standard method, this means Tenax® sampling followed by thermal desorption and GC-MS analysis, these acids could not be detected sufficiently. The aim oft this study is the comparison of two different methods for the determination of acetic and formic acid. The sampling of method one, which is usually used for identification and quantification of VOCs, is done in accordance with ISO 16000-6 and ISO 16017-1 on Carbotrap® 202 multi-bed thermal desorption tube by subsequent identification and quantification with GC-MS. Method two is based on sampling on 2,4-dinitrophenylhydrazine (DNPH) cartridges, derivatisation, elution, identification and quantification of the derivatives with LC-MS/MS (liquid chromatography – mass spectrometry/mass spectrometry). N2 - Viele Konstruktions- und Baumaterialien, wie Holz, Kleber und Anstriche, sind mögliche Quellen für leicht flüchtige organische Verbindungen (VVOC) und flüchtige organische Verbindungen (VOC), wie Ameisen- und Essigsäure. Bedingt durch die hohe Dichtigkeit und den damit verbundenen niedrigen Luftwechsel in neuen Gebäuden können die Konzentrationen dieser gesundheitsgefährdenden Substanzen beträchtlich ansteigen. Um das Risiko zu minimieren, sollen Emissionen aus Bauprodukten identifiziert und quantifiziert werden. Mit der üblichen Standardmethode, die auf einer Luftprobenahme auf Tenax® und anschließender Analyse mittels GC-MS basiert, können diese Säuren nicht ausreichend detektiert werden. Ziel dieser Arbeit ist der Vergleich von zwei unterschiedlichen Methoden zur Bestimmung von Essig- und Ameisensäure. Die Luftprobenahme der ersten Methode, die üblicherweise zur Identifizierung und Quantifizierung von VOC genutzt wird, wurde gemäß ISO 16000-6 and ISO 16017-1 auf Carbotrap® 202, ein mit mehreren Adsorbentien gepacktes Thermodesorptionsrohr, mit anschließender Identifikation und Quantifizierung mittels GC-MS durchgeführt. Die zweite Methode basiert auf einer Luftprobenahme mittels 2,4-Dinitrophenylhydrazin-(DNPH)-Kartuschen, Derivatisierung, Elution, Identifikation und Quantifizierung der Derivate mit LC-MS/MS (Flüssigkeitschromatographie – Massenspektometrie/Massenspektometrie). KW - Formic acid KW - Acetic acid KW - VVOCs KW - Air sampling KW - DNPH PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-255911 UR - http://www.gefahrstoffe.de/gest/article.php?data[article_id]=65887 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 72 IS - 3 SP - 84 EP - 88 PB - Springer-VDI-Verlag CY - Düsseldorf AN - OPUS4-25591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Brosig, Laura A1 - Horn, Wolfgang A1 - Pyza, Lars A1 - Jann, Oliver T1 - Ringversuch zur Einführung der Geruchsmessungen nach DIN ISO 16000-28 in die Bewertung von Bauprodukten N2 - Während in der Vergangenheit insbesondere die Entwicklung einer sensorischen Prüfmethode (in DIN ISO 16000-28 und VDI 4302-1 genormt und im AgBB-Schema verankert) für die Bewertung von Bauprodukten im Vordergrund der Betrachtungen stand, wurde im Rahmen der vom UBA initiierten Pilotphase mithilfe des Ringversuches erstmals die institutsübergreifende Anwendbarkeit dieser Verfahren untersucht. Ziel dabei war es, noch bestehende Schwierigkeiten im Umgang mit der Prüfmethode zu identifizieren und Empfehlungen für das weitere Vorgehen herauszuarbeiten. KW - Geruchsmessung KW - Empfundene Intensität KW - Hedonik KW - VOC KW - Bauprodukt PY - 2015 UR - http://www.umweltbundesamt.de/publikationen/ringversuch-zur-einfuehrung-der-geruchsmessungen SN - 1862-4804 VL - 88/2014 SP - UBA-FB 002049, EP - 1-141 CY - Dessau-Roßlau AN - OPUS4-34885 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Mull, Birte A1 - Jann, Oliver T1 - Biozidemissionen aus Materialien in die Luft N2 - Die meisten organischen Biozide gehören zu der Gruppe der schwerflüchtigen organischen Verbindungen (SVOC – semi volatile organic compounds). Zu den klassischen Bioziden zählen u.a. Lindan, Pentachlorphenol PCP) und Dichlordiphenyltrichlorethan (DDT) und zu den neueren u.a. Dichlofluanid, Tebuconazol und Permethrin. Biozide kamen in Museen vor allem in den 50er und 60er Jahren zum Schutz der Exponate zum Einsatz,1 wo sie hauptsächlich in Depoträumen zu finden sind, in welchen sie zum akuten und zum präventiven Schutz vor Schadorganismen eingesetzt wurden.2 Im Laufe der Zeit wurde jedoch festgestellt, dass sich der Einsatz von Bioziden negativ auf die menschliche Gesundheit auswirkt und auch zu Schäden an den behandelten Exponaten führen kann. 3 Verschiedene Möglichkeiten der Biozidanalytik und der Einfluss von Senkeneffekten auf die Analytik werden in diesem Beitrag vorgestellt. KW - Biozidanalytik KW - Schwerflüchtige organische Verbindungen KW - Emissionsmesskammer PY - 2015 SP - 12 EP - 14 CY - Berlin AN - OPUS4-35394 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen flüchtiger Verbindungen aus Bauprodukten N2 - Vielzahl unterschiedlicher VOC kann aus Bauprodukten freigesetzt werden. In den meisten Bauproduktgruppen gibt es sowohl emissionsarme als auch emissionsreiche Produkte. Manche VOC produktgruppenspezifisch: Siloxane/Silikon, andere VOC unspezifisch wie Formaldehyd, Essigsäure VOC-Analytik und Gerüche zeigen im Allgemeinen keinen Zusammenhang. Schwerflüchter zeigen Langzeitemission und ausgeprägte Senken-/Memoryeffekte. Radon kann aus manchen Bauprodukten abgegeben werden und bei luftdichten Gebäuden in radonarmen Gebieten Haupt-Radonquelle sein. Radonexhalation kann grundsätzlich (statisch/dynamisch) mit VOC-Kammern - ergänzt mit geeigneten Messgeräten - bestimmt werden. T2 - VDI-Wissensforum: Bauprodukte und gesunde Innenraumluft CY - Düsseldorf, Germany DA - 22.11.2016 KW - VOC KW - Bauprodukte KW - Emissionen KW - Luft KW - Radon PY - 2016 SP - 3 EP - 23 PB - VDI CY - Düsseldorf AN - OPUS4-38589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brosig, Laura A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Method-verification and optimisation of the standardised assessment of odour intensity regarding ISO 16000-28 N2 - Besides measurement of VOC emissions also the evaluation of odour emissions and the perceived intensity of odours gains in importance. Due to difficulties detected in the measurement method of the perceived intensity described in (ISO 16000-28, 2012) the introduction of “reference” odours will be recommended for the training of panellists and as basis for interlaboratory comparisons. In order to generate the “reference” odours standard liquid substances were directly injected into the main gas flow provided to the panellists. One of the substances tested was ethyl acetate. A pre-evaluation was conducted with six untrained panellists and has shown that ethyl acetate is potentially suitable as reference odour. For further validation of those “reference” odours they additionally will be provided to and evaluated by trained panellists of well established-measurement institutes. T2 - Indoor Air 2016 The 14th international conference of Indoor Air Quality and Climate CY - Ghent, Belgium DA - 03.07.2016 KW - Odour assessment KW - Perceived odour intensity KW - Reference odour KW - Emission testing KW - Building products PY - 2016 SN - 978-0-9846855-5-4 SP - Paper 568, 1 EP - 6 AN - OPUS4-38373 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brosig, Laura A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Ringversuche zur Einführung von Geruchsmessungen in die Bewertung von Bauprodukten entsprechend der DIN ISO 16000-28 und VDI 4302-1 N2 - The DIN ISO 16000-28 and VDI 4302-1 describe a method for the assessment of the perceived intensity of odours. It is based on a trained assessment panel using a referencing scale that provides defined acetone concentrations. Due to the AgBB-scheme including a place holder for odour assessment it is currently checked whether the method is applicable. To check the applicability a pilot phase regarding the „Implementation of Odour Measurements into the Assessment of Building Products“ was started by AgBB1 in 2012. Düring this phase amongst others two interlaboratory tests were conducted. The first one in 2012 served to test the applicability and to identify need and potential for improvement. Based on those findings an additional Standard Operation procedure was developed for the second interlaboratory test in 2014. The second interlaboratory test confirmed the findings of the first one and the need for improvement of the measurement method as well. Nonetheless both tests showed Standard deviations of reproducibility between 20 and 40%. Standard deviations of reproducibility of well-established interlaboratory tests for VOCs show comparable results. T2 - 17. Workshop - Geruch und Emissionen bei Kunststoffen CY - Kassel, Germany DA - 16.03.2015 PY - 2015 SP - 8-1 EP - 8-9 AN - OPUS4-33075 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, B. A1 - Panasková, J. A1 - Müller, D. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Scutaru, A.M. A1 - Plehn, W. T1 - Entwicklungen der Bewertungsmethodik von Gerüchen in Innenräumen N2 - Um eine gute Luftqualität in Gebäuden zu erreichen, müssen Reinigungslasten durch Lüften aus Räumen abgeführt bzw. vermieden oder verringert werden. Wird der Luftwechsel verringert, verschlechtert sich die Raumluftqualität, und die Zufriedenheit der Nutzer nimmt ab. An Arbeitsplätzen kann es bei schlechter Luftqualität und der daraus resultierenden Unzufriedenheit zu einer geringeren Produktivität der Beschäftigten kommen. Um die Reinigungslasten und deren Wirkung auf den Raumnutzer überdas Geruchsempfinden zu verringern, ist neben einer messtechnischen Erfassung der Verunreinigungen auch eine sensorische Prüfung in Innenräumen und von Bauprodukten notwendig. In diesem Artikel wird die Entwicklung der Bewertungsmethodik von Gerüchen im Innenraum erläutert und auf Anwendungen eingegangen. KW - Geruch KW - Innenraum KW - Bauprodukte KW - Bewertung PY - 2014 SN - 2195-643X VL - 135 IS - 2 SP - 70 EP - 82 PB - DIV Deutscher Industrieverlag GmbH CY - München AN - OPUS4-32403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nohr, Michael A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Richter, Matthias A1 - Lorenz, W. T1 - Development of a multi-VOC reference material for quality assurance in materials emission testing N2 - Emission test chamber measurement is necessary to proof building materials as sources of volatile organic compounds (VOCs). The results of such measurements are used to evaluate materials and label them according to their potential to emit harmful substances, polluting indoor air. If only labelled materials were installed indoors, this would improve indoor air quality and prevent negative impacts on human health. Because of the complex testing procedure, reference materials for the quality assurance are mandatory. Currently, there is a lack of such materials because most building products show a broad variation of emissions even within one batch. A previous study indicates lacquers, mixed with volatile organic pollutants, as reproducible emission source for a wide range of substances. In the present study, the curing of the lacquer-VOC mixture inside micro-chambers was optimised. Therefore, the humidity and the chamber flow were varied. Typical indoor air pollutants with a wide range of volatilities, for example, styrene, n-hexadecane, dimethyl and dibutyl phthalate were selected. It turned out that, under optimised curing parameters inside the micro-chamber, their emission can be reproduced with variations of less than 10 %. With this, a next important step towards a reference material for emission testing was achieved. KW - Reference material KW - Emission KW - Emission test chamber KW - Micro-chamber KW - VOC PY - 2015 DO - https://doi.org/10.1007/s00216-014-8387-2 SN - 1618-2642 SN - 1618-2650 VL - 407 IS - 11 SP - 3231 EP - 3237 PB - Springer CY - Berlin AN - OPUS4-32404 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Pech, Anja A1 - Mull, Birte A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Determination of methanol and ethanol in test chamber air by using TDS-GC-FID N2 - A method for the determination of very volatile organic compounds (VVOC) in air was developed and successfully tested for methanol and ethanol. Carbotrap 300 (R) (a multi-bed tube using Carbopack C (R), Carbopack B (R) and Carbosive SIII (R)) was selected as sorption material for thermal desorption and tested for its suitability for emission test chamber measurements. The adsorption behaviour and the chromatographic results are influenced negatively by spiking aqueous solutions on the adsorption medium for calibration purposes. The latter effect can be reduced by blowing dry air across the adsorbent to remove the adsorbed water. Detection and quantification limits were determined for a GC-FID system and compared to GC-MS. The applicability of the method was tested with a methanol eliminating silane modified polymeric adhesive (SMP-adhesive for parquet) in an emission test chamber. T2 - Indoor Air 2014 - 13th International conference on indoor air quality and climate CY - Hong Kong, People's Republic of China DA - 07.07.2014 KW - Methanol KW - Ethanol KW - VVOC KW - Thermal desorption KW - Carbotrap 300 PY - 2014 SP - B6-HP0620, 1-2 AN - OPUS4-32323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen aus Bauprodukten in der Innenraumverwendung T2 - VDI-Wissensforum "Bauprodukte und gesunde Innenraumluft" CY - Düsseldorf, Deutschland DA - 2014-11-25 PY - 2014 AN - OPUS4-32330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionsarme Materialien und Produkte - Basis für eine gute Innenraumluftqualität N2 - Vielzahl unterschiedlicher VOC kann aus Bauprodukten freigesetzt werden. In den meisten Bauproduktgruppen gibt es sowohl emissionsarme als auch emissionsreiche Produkte. Manche VOC sind produktgruppenspezifisch, z.B. Siloxane/Silikon, andere VOC unspezifisch wie Formaldehyd und Essigsäure. VOC-Analytik und Gerüche zeigen im Allgemeinen keinen Zusammenhang. Schwerflüchter zeigen Langzeitemission und ausgeprägte Senken-/Memoryeffekte. Drucker/Kopierer emittieren neben VOC auch Fein- und Ultrafeinpartikel. Radon kann aus manchen Bauprodukten abgegeben werden und bei luftdichten Gebäuden in radonarmen Gebieten Haupt-Radonquelle sein. Radonexhalation kann grundsätzlich (statisch/dynamisch?) mit VOC-Kammern - ergänzt mit geeigneten Messgeräten - bestimmt werden. Es existiert eine Vielzahl von Labels für emissionsarme Bauprodukte. Gerade bei modernen, dichten Bauten mit geringem natürlichen Luftwechsel sind hohe Schadstoffkonzentrationen zu erwarten, wenn nicht emissionsarme Materialien und Produkte zum Einsatz kommen. T2 - Kolloquium des FG Umweltchemie am Institut für Technischen Umweltschutz, Sommersemester 2016 CY - Berlin, Germany DA - 04.07.2016 KW - Materialien KW - Emissionen KW - Luft KW - Produkte PY - 2016 AN - OPUS4-37100 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Emissions of very volitale organic compounds (VVOC) from particle boards N2 - The latest version of the German AgBB evaluation scheme (2015) for construction products includes some VVOC, e.g. formaldehyde, acetaldehyde and acetone. For these VVOC so-called LCI values (lowest concentration of interest) were derived which are used for the calculation of the so-called R-value (risk index, see reference 1 for the calculation). Test chamber measurements of particle boards show that the emissions of VVOC might have significant impact on the R-value and therefore for the health evaluation. T2 - The 14th international conference of Indoor Air Quality and Climate, Indoor Air 2016 CY - Gent, Belgium DA - 03.07.2016 KW - Formaldehyde KW - AgBB evaluation scheme KW - Particle board KW - OSB KW - VVOC KW - Emission test chamber PY - 2016 SP - Paper 965, 1 AN - OPUS4-37030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pech, Anja A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Analysis of very volatile organic compounds (VVOC) with thermal desorption GC-MS N2 - Most VVOC were rarely considered in the evaluation of construction products. (Salthammer, 2014) In Germany this will change because the latest version of the German AgBB scheme for health evaluation (2015) now include VVOC, e.g. ethyl acetate and ethanol. In this study selected compounds were tested with the procedure described in ISO 16017 and a method for measuring VVOC with thermal desorption was developed. Three different adsorbents Tenax TA, Carbograph 5TD and Carbopack X were tested to analyse VVOC according to ISO 16017. For the tested VVOC, Carbograph 5TD showed the best results under the chosen analytical conditions. T2 - Indoor Air 2016, The 14th international conference of Indoor Air Quality and Climate CY - Gent, Belgium DA - 03.07.2016 KW - Thermal desorption KW - VVOC KW - Carbograph 5TD KW - Carbopack X PY - 2016 SP - Paper 889, 1 EP - 2 AN - OPUS4-37035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Janine A1 - Jann, Oliver A1 - Wilke, Olaf T1 - Emissions of formaldehyde from acoustic tiles N2 - Acoustics is an important aspect for large rooms especially in schools, kindergartens and offices. Foam tiles made from melamine resins are often used for acoustic insulation because they show good fire resistance and good thermal insulation properties. But they can emit formaldehyde. In Germany there are cases with a resulting indoor air concentration of higher than 100 µg/m³. In this study samples from two schools and one office were investigated. Additionally, new tiles were purchased and tested to evaluate the general potential as formaldehyde source. T2 - Healthy Buildings 2017 Europe CY - Lublin, Poland DA - 02.07.2014 KW - Building product KW - Emission test chamber KW - Formaldehyde KW - Foam tiles PY - 2017 SN - 978-83-7947-232-1 SP - Paper 0176, 1-2 AN - OPUS4-41574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, B. A1 - Dahms, A. A1 - Bitter, F. A1 - Wargocki, P. A1 - Olesen, B. A1 - Knudsen, H.N. A1 - Afshari, A. A1 - Jann, Oliver A1 - Horn, Wolfgang A1 - Müller, D. A1 - Airaksinen, M. A1 - Järnström, H. A1 - Tirkkonen, T. A1 - Witterseh, T. T1 - Material labelling: Combined material emission tests and sensory evaluations T2 - Indoor Air 2008, 11th International Conference on Indoor Air Quality and Climate CY - Copenhagen, Denmark DA - 2008-08-17 KW - Material labelling KW - Emission test KW - Sensory evaluation KW - Odour intensity KW - Acceptability PY - 2008 IS - Paper 1066 SP - 1 EP - 8 AN - OPUS4-18047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen flüchtiger organischer Verbindungen aus Bauprodukten T2 - VDI-Wissensforum: Schadstoffe in Bauprodukten CY - Cologne, Germany DA - 2010-11-09 PY - 2010 AN - OPUS4-22330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Seeger, Stefan A1 - Bresch, Harald A1 - Brödner, Doris A1 - Juritsch, Elevtheria A1 - Jann, Oliver T1 - Sampling and characterisation of ultra fine particles released from laser printers T2 - Indoor Air 2008, August 17-22, 2008 CY - Copenhagen, Denmark DA - 2008-08-17 KW - Aerosol KW - Ultra fine particle KW - Laser printer KW - Cyclosiloxanes PY - 2008 IS - Paper ID: 239 SP - 1 AN - OPUS4-17865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen flüchtiger organischer Verbindungen aus Bauprodukten T2 - VDI-Wissensforum: Schadstoffe in Bauprodukten CY - Mannheim, Germany DA - 2008-11-12 PY - 2008 AN - OPUS4-18291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Brödner, Doris A1 - Kalus, Sabine A1 - Juritsch, Elevtheria A1 - Müller, B. A1 - Müller, D. A1 - Kasche, J. T1 - Chemische analytische Bewertung von Baustoffemissionen T2 - Deutsche Kälte-Klima-Tagung 2008 CY - Ulm, Deutschland DA - 2008-11-20 KW - AgBB-Schema KW - VOC KW - Emissionen KW - Bauprodukte KW - Bewertung Emissionen PY - 2008 IS - AA.IV.15 SP - 1 EP - 8 AN - OPUS4-18406 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Innenraumluftschadstoffe - Emissionsarme Materialien und Produkte T2 - Kolloquium "Messen und Beurteilen von Luftschadstoffen", TU Berlin CY - Berlin, Germany DA - 2010-07-02 PY - 2010 AN - OPUS4-22145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Innenraumluftschadstoffe T2 - Ringvorlesung Fachhochschule Eberswalde CY - Eberswalde, Germany DA - 2002-10-18 PY - 2002 AN - OPUS4-5868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rockstroh, Jens A1 - Jann, Oliver A1 - Wilke, Olaf A1 - Horn, Wolfgang T1 - Development of a reliable test method for laser printers, copiers and multifunctional devices in emission test chambers - Part 1 N2 - Background to the studies was the revision of the current selection criteria of the German ecolabel Blauer Engel (“Blue angel“) for copiers and printers. In the requirements limits were set for ozone, dust and styrene emissions. The former test methods did no longer correspond to today’s requirements with regard to emission measurements. In addition, the emission behaviour of hardcopy devices due to the use of different and non-com parable test methods has been recently discussed controversely. For this reason a new test method had to be developed which enables a reliable, reproducible determination of emission rates (ER) for dust, ozone and VOC (volatile organic compounds). The basis for this was the ECMA-Standard 328 compiled by ECMA (European Computer Manufacturer Association) using dynamic chamber measurements. Nine different machines, desktop laser printers as well as office devices like bigger copiers and multifunctional devices were investigated. As a result of the study new criteria for the Blauer Engel for copiers, printers and a new created for multifunctional devices, concerning TVOC, ozone and dust emission were determined. Additionally a model is presented calculating the concentrations in real rooms under usual printing conditions derived from the test chamber results. PY - 2005 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 65 IS - 3 SP - 71 EP - 80 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-7210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Testing Emissions of Volatile Organic Compounds from Products and Materials T2 - International Congress-ENERIS CY - Paris, France DA - 2001-06-14 PY - 2001 AN - OPUS4-7199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver A1 - Wilke, Olaf T1 - Comparison of FLEC with other climate chambers, Gemeran experiences T2 - 2nd International FLEC Symposium CY - Copenhagen, Denmark DA - 2001-09-06 PY - 2001 SP - 18 EP - 27 AN - OPUS4-7204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jann, Oliver A1 - Wilke, Olaf A1 - Brödner, Doris ED - Woods, J. ED - Grimsrud, D. ED - Boschi, N. T1 - Procedure for the determination and limitation of VOC-emissions from furnitures and coated wood based products T2 - Healthy Buildings/IAQ '97 ; ASHRAE Annual IAQ Conference ; 5th ISIAQ International Conference on Healthy Buildings CY - Bethesda, MD, USA DA - 1997-09-27 PY - 1997 SN - 0-929900-25-1 VL - 3 SP - 593 EP - 598 CY - Washington, DC AN - OPUS4-7237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Untersuchungen zum Emissionsverhalten strahlengehärteter Lacksysteme mit Hilfe von Emissionsmesskammern T2 - 4. Freiburger Polymertag CY - Freiburg, Germany DA - 1999-05-27 PY - 1999 AN - OPUS4-7190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Eco-Label for low emission wood products and wood base products (RAL-UZ-38) - Part 2: Test procedure and results T2 - Healthy Buildings 2000 CY - Espoo, Finland DA - 2000-08-06 PY - 2000 AN - OPUS4-7195 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jann, Oliver A1 - Wilke, Olaf T1 - Emissionen aus Laserdruckern und -kopierern N2 - Drucker, Kopierer und Multifunktionsgeräte können zu einer Schadstoffbelastung der Innenraumluft beitragen. Insbesondere Staub, Ozon und flüchtige organische Verbindungen (VOC, Volatile Organic Compounds) werden beobachtet. Geräte mit besonders geringen Emissionen, die weitere umweltrelevante Anforderungen einhalten, können mit dem Umweltzeichen Blauer Engel ausgezeichnet werden. Die Vergabegrundlage für den Blauen Engel begrenzt neben den genannten Stoffen auch noch speziell die Emission von Benzol und Styrol, und sie enthält die Prüfvorschrift zur Bestimmung der Emissionen. In der vorliegenden Publikation werden Ergebnisse von Emissionsmessungen an 57 verschiedenen Geräten unterschiedlicher Hersteller aus den Jahren 2003 bis 2004 vorgestellt. Ein besonderer Schwerpunkt liegt hierbei neben der Darstellung der summarischen VOC-Emissionen (TVOC, Total Volatile Organic Compounds) auf den wichtigsten Einzel-VOC, wie z.B. Benzol, Styrol, Phenol, Xylole. Diese für Drucker und Kopierer typischen Verbindungen ließen sich mit Emissionsraten von bis zu einigen Milligramm pro Stunde feststellen. Zusätzlich traten auch Siloxane mit vergleichbaren Raten auf, die bisher als Emissionen aus Druckern und Kopierern nur wenig Beachtung fanden. In einigen Fällen waren hohe Emissionen an VOC, die sich einer ausreichenden Identifizierung entzogen, feststellbar. Aus den ermittelten Emissionsraten wurden für einen Modellraum mögliche resultierende Raumluftkonzentrationen berechnet. Diese Berechnungen setzen voraus, dass Emissionen nicht den gesamten Tag über erfolgen, sondern unter üblichen Nutzungsbedingungen über maximal 10% des Arbeitstages. Für Emissionen der druckbereiten Geräte hingegen wurde eine Belastung über den ganzen Tag zugrunde gelegt. Ergänzend werden Emissionsraten für Ozon und Staub vorgestellt. English: Hardcopy devices like printers, copiers and multifunctional devices contribute to indoor air pollution. Low emitting devices, that fulfil additional environment related requirements, can be labelled with the eco label "Blue Angel". It limits emissions of benzene, styrene, TVOC, dust and ozone. Results are given for 57 different devices investigated during the years 2003 and 2004. Additionally to TVOC, benzene and styrene further information is given for other emitted VOC like phenol and xylenes. These typical VOC showed emission rates up to some mg/ h but some more uncommon VOC like siloxanes were found in a comparable range, too. In some cases high emission rates were found for compounds which could not be identified. The measured emission rates were taken to calculate indoor air concentrations for a typical situation. For this purpose it was considered that printing is normally limited to less than 10 % of a working day whereas emissions from the stand by phase occur all day long. In addition emission rates for ozone and dust are presented. KW - Drucker KW - Emissionen KW - Kopierer KW - Ozon KW - Staub KW - VOC KW - Copiers KW - Dust KW - Emissions KW - Ozone KW - Printers PY - 2006 SN - 1430-8681 VL - 11 IS - 5 SP - 309 EP - 317 PB - Ecomed CY - Landsberg, Lech AN - OPUS4-13872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - VOC-Emissionen aus Bauprodukten T2 - VDI-Seminar "Schadstoffe in Bauprodukten" CY - Mannheim, Germany DA - 2007-04-24 PY - 2007 AN - OPUS4-14838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Kasche, J. A1 - Bitter, F. A1 - Müller, D. A1 - Müller, B. T1 - Environmental and Health Provisions for Building Products - Identification and evaluation of VOC emissions and odour exposure (Research Report 202 62 320 / UBA-FB 001002) N2 - In this study 50 construction products were tested in emission test chambers according to the requirements of the AgBB-scheme: 7 acrylic and 6 silicone sealants, 6 paste-like synthetic resin plasters, 13 wood based products, 4 adhesives, 5 lacquers, 6 wall paints and 3 further construction products. VOC and odour emissions were tested on the 1st, 3rd, 10th, and 28th day. In addition to the VOC-measurements, a test procedure was developed to evaluate odour emission of construction products.This test is planned to be implemented into the AgBB-Scheme. A direct evaluation by a sensory panel in the emission test chamber was not possible. So the odour samples were collected in 300- litre tedlar bags which were evaluated later. Odour intensity of the samples was compared with different acetone concentrations. Within this study an interlaboratory comparison was conducted using the newly developed odour test method. Additionally, VVOC emissions, detection of carcinogenic compounds, repeatability of emission test chamber tests, and other issues are presented. This project has shown that construction products can be evaluated in accordance with the AgBB scheme. A sensory evaluation is intended to be introduced in the AgBB scheme. A method for this evaluation is described in this study. The test procedure should be enhanced and validated for practical utilisation. KW - Building products KW - Emissions KW - Odour KW - AgBB-Scheme KW - Chamber tests KW - Interlaboratory study KW - Construction products KW - Emission test chamber KW - Odour evaluation KW - VOC KW - VVOC KW - SVOC KW - Thermal desorption KW - GC/MS KW - GC-ODP KW - Odour standard of comparison KW - Gas sensor KW - Acrylic and silicone sealant KW - Wood-based product KW - Paints KW - Lacquers KW - Interlaboratory comparison PY - 2007 UR - http://www.umweltbundesamt.de/publikationen/environmental-health-provisions-for-building SN - 1862-4804 SN - 0722-186X IS - 21 SP - 1 EP - 381 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-15931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Jann, Oliver A1 - Kemski, J. A1 - Klingel, R. A1 - Schneider, Uwe A1 - Krocker, Christian T1 - Investigations on radon exhalation of different building materials N2 - The inhalation of 222Rn (radon) is one of the most important reasons for lung cancer, after smoking. Usually, the geological subsoil and the building ground are the dominant sources for enhanced indoor radon levels. Additionally, building materials can increase indoor radon concentrations when these materials contain higher contents of 226Ra (radium), especially in combination with low air exchange rates. For a realistic estimation of indoor radon concentrations, it is helpful to carry out measurements of radon exhalation rates from relevant materials using emission test chambers. In Germany, it is aspired to limit the total indoor radon concentration to 100 Bq/m3, whereby building materials should contribute at most 20 Bq/m3. Within a project financed by the German Institute for Construction Technology (DIBt), a practical oriented measurement procedure of the radon exhalation of building materials in accordance to ISO 16000-9 was developed to have a means for the assessment of these materials with respect to their indoor use. Test chambers with different volumes were used. The tested materials were mainly used for wall constructions (e.g., bricks, light-weight concrete) and have known specific radium activities and radon exhalation rates. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Radon exhalation KW - Building material KW - Emission test chamber KW - Indoor air PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-24155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jann, Oliver ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Emissions from Materials N2 - Emissions from materials influence the surrounding environment. Gaseous emissions - mainly volatile organic compounds (VOCs) - into indoor air are of Special interest due to the fact that they affect indoor air Quality (IAQ). VOCs are of importance because they are strongly related to the so-called sick-building Syndrome (SBS). Materials are not the only source of indoor air pollution. Other important sources are every type of combustion (e.g. fire places, gas cooking), especially smoking (environmental tobacco smoke (ETS)) and the use of household Chemicals (sprays, solvents e.g.). Whereas these kinds of sources can be influenced by the user (to use or not to use it) materials emissions cannot be influenced by the user to the same extent. Often the user is simply not aware that materials might have emissions. PY - 2011 SN - 978-3-642-16640-2 SP - 860 EP - 869 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Plehn, W. A1 - Müller, D. T1 - VOC emissions from building materials accompanying sensory tests for different evaluation schemes N2 - Within a follow up project of a former study (Horn et al. 2005) emissions and odor from different types of construction products were investigated (financed by the German Federal Environmental Agency - FKZ 37 07 62 300). The tested materials were mainly those used for construction of floors indoors. For this type of materials in Germany several labeling procedures exist which are based on Emission chamber testing. Two important labeling procedures in Germany are based on the AgBBevaluation scheme (Däumling et al. 2005). For some applications (flooring material) it is the mandatory Ü-mark of DIBt (German Institute for Construction Technology). Furthermore for carpets, adhesives and many other products, like sealants, mattresses, furniture and so on the voluntary blue angel mark exist. Within this scheme the volatile organic compounds (VOC) compounds are measured with well established procedures and are evaluated with LCI-values which were derived from health information. Beyond that many complaints according to building products are caused by odors. Therefore an evaluation procedure for the odor is very important and should be implemented into all of the mentioned labeling schemes. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Odor KW - Construction product KW - VOC-emission KW - Evaluation KW - AgBB PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Horn, Wolfgang A1 - Müller, D. A1 - Plehn, W. T1 - Results of sensory tests and sensory-limit settings for building materials in Germany N2 - Indoor air pollutants influence the health and comfort of building occupants and consequently the energy consumption of the building. The pollutants are emitted by various sources. Among these sources, building products are of particular importance. To control the emission of pollutants from building materials, a few different voluntary labelling Systems have been introduced in Europe. In Germany also mandatory “Principles for the health assessment of construction products used in interiors” have been applied for the technical approval of floor coverings since 2004. This procedure is based on the assessment scheine of the Committee for Health-related Evaluation of Building Products (AgBBScheme). The sensory-limit settings for building-material label Blue Angel offer consumer to differ not only low-emission but also low-odour Building materials from another building materials. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Perceived air-quality KW - Odour evaluation KW - Odour labelling KW - Test procedure KW - Standardisation PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Masuck, I. A1 - Hutzler, C. A1 - Jann, Oliver A1 - Luch, A. T1 - Inhalation exposure of children to fragrances present in scented toys N2 - When utilized in the perfuming of children's toys, fragrances capable of inducing contact allergy in human skin may also become bioavailable to children via the inhalation route. The aim of this study was to determine the area-specific emission rates of 24 fragrances from a plasticized PVC reference material that was meant to mimic a real plastic toy. This material was introduced into an emission chamber for 28 days at handling conditions or at worst-case conditions. As a result, fragrances can be separated into three categories according to their emission rates ranging from 0.0041 to 16.2 mg/m² × h, i.e., highly volatile, semivolatile, and low-volatile compounds. Compounds of the first and second categories were monitored with decreasing emission rates. Substances of the third category were detected with increasing emission rates over time. Further, higher temperatures led to higher emission rates. The emission concentration of fragrances from four real scented toys varied between 1.10 and 107 µg/m³ at day 1 in the test chamber. Therefore, short-term inhalation exposure to fragrances originating from toys was in the range of 0.53–2700 ng/kg BW/d for the children of age 1 and older. Long-term exposure to these fragrances was calculated in the range of 2.2–220 ng/kg BW/d. KW - Scented toys KW - Fragrance allergens KW - Inhalation exposure KW - Emission chamber KW - Volatile organic compounds PY - 2011 DO - https://doi.org/10.1111/j.1600-0668.2011.00727.x SN - 0905-6947 SN - 1600-0668 VL - 21 IS - 6 SP - 501 EP - 511 PB - Danish Techn. Pr. CY - Copenhagen AN - OPUS4-24791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, B. A1 - Panasková, J. A1 - Danielak, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Müller, D. T1 - Sensory-based evaluation of building product emissions - Integration into the Blue Angel award criteria and assessment scheme of the Committee for Health Evaluation of Building Products (UBA-FB 001500 / Förder-Kennz. 370762300) N2 - Emissions from building products can considerably impair the quality of indoor air. The AgBB scheme is employed to evaluate the emissions of volatile organic compounds (VOC) from building products. The hygienic evaluation according to the AgBB scheme requires product-specific measuring procedures. These are available for a range of products. They have been validated in co-operation with several research and testing institutes and have been included in the criteria for awarding the Blue Angel ecolabel. The evaluation is, however, stricter and generally has lower limits. VOC emissions and odours can cause health problems so testing using sensors is an important element in the evaluation of building products and has – for reasons of precaution – been set down in the AgBB scheme. The main goal of the project was to derive a method of evaluation using sensors and limits for awarding the Blue Angel and for the AgBB scheme. Based on the research conducted (see Chapter 5 Results and Discussion), perceived intensity and hedonics were suggested as a suitable Evaluation method. The derivation of limits for the evaluation using sensors on the 28th day was effected in the present study through the additional questioning of the test subjects on the reasonability of a sample. For the Blue Angel, there could be different limits of perceived intensity and hedonics for each group of products. A preliminary suggestion for possible limits – for all product groups – is a perceived intensity of 7 pi (5 pi + 2 pi as confidence coefficient, Chapter 5.1.5) and -1 (0+/-0.8, rounded to -1) for the hedonic value. KW - Labelsysteme KW - VOC KW - Geruch KW - Geruchstest KW - Emissionsmessungen KW - Building product KW - Directive KW - Health care KW - Pollutant KW - Test method KW - Hydrocarbon KW - Testing using sensors KW - Emission KW - Emission test chamber KW - Odour KW - AgBB scheme KW - Health assessment KW - Assessment procedure KW - Volatile organic compounds KW - Very volatile organic compounds KW - VVOC KW - Semi volatile organic compounds KW - SVOC KW - Thermal desorption KW - GC/MS KW - GC-ODP KW - Odour standard of comparison KW - Floor coverings KW - Coverings KW - Blue Angel KW - Odour evaluation KW - Acceptability KW - Perceived intensity KW - Hedonic KW - Reasonability KW - Standardization KW - Environmental sign KW - Volatile emission KW - Product labelling PY - 2011 UR - http://www.umweltbundesamt.de/publikationen/sensory-based-evaluation-of-building-product SN - 1862-4804 IS - 61 SP - 1-133, Annex 1-109 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-25200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Radonexhalationsmessungen mit VOC-Kammern T2 - Radon-Fachgespräch BfS CY - Berlin, Germany DA - 2012-06-05 PY - 2012 AN - OPUS4-26066 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen flüchtiger organischer Verbindungen aus Bauprodukten T2 - VDI-Wissensforum "Bauprodukte und gesunde Innenraumluft" CY - Düsseldorf, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25051 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen aus Bauprodukten in die Luft - Neuere Entwicklungen T2 - Technikforum "Bauprodukte und gesunde Innenraumluft" CY - Düsseldorf, Germany DA - 2012-11-20 PY - 2012 AN - OPUS4-26949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emission von Bioziden aus Materialien in die Luft T2 - 6. N.i.Ke.-Workshop "Segen und Fluch - Biozide: Verwendung, Analytik, Bewertung" CY - Berlin, Germany DA - 2012-11-19 PY - 2012 AN - OPUS4-27460 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Jann, Oliver T1 - Different possibilities for the statistical evaluation of round robin tests for volatile organic compounds in emission test chambers N2 - Emission testing of products is currently a rapidly increasing field of activity. The amounts of volatile organic compounds (VOC) which emit from products in emission test Chambers are used to evaluate these products. Typically labelling procedures for construction products are based on emission test chamber measurements. This performance should be verified. Possibly this can be performed due to testing of one material at different laboratories within a round robin test. Therefore it is necessary that a reference material exists which can be used for such round robin tests or as part of the quality management System to ensure comparable results. The different Statistical evaluation possibilities of a round robin test with a constant reference material for VOCs (volatile organic compounds) in emission test Chambers are the main focus of the presented paper. T2 - Healthy Buildings 2012 - 10th International conference CY - Brisbane, Australia DA - 08.07.2012 KW - Reference material KW - Round robin test KW - Emission test chamber KW - VOC-emission KW - Product emission testing PY - 2012 SN - 978-1-921897-40-5 SP - 1 EP - 2 (8B.6) AN - OPUS4-27526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wilke, Olaf A1 - Wiegner, Katharina A1 - Jann, Oliver A1 - Brödner, Doris A1 - Scheffer, Harald T1 - Emissionsverhalten von Holz und Holzwerkstoffen (UBA-FB 001580) N2 - In diesem Vorhaben wurden 8 OSB-Platten und sieben Leimholzplatten aus Baumärkten gemäß den Vorgaben des AgBB-Schemas in Emissionsmesskammern geprüft. Hinzu kamen Messungen an 17 im Technikum hergestellten OSB, an denen der Einfluss von Herstellungsparametern auf VOCEmission untersucht wurde. Grundsätzliches Ziel war es, durch die Untersuchungen Lösungsansätze für die Emissionsminderung von VOC aus Holzwerkstoffen zu finden. Dazu wurde auch der Einsatz von Antioxidantien bei der OSB-Herstellung getestet. Die Emissionen des Rohstoffes Kiefernholz wurden an 6 Proben aus Splint- oder Kernholz aus unterschiedlichen Stammabschnitten einer frisch gefällten Kiefer untersucht. Insgesamt konnte mit dem Projekt gezeigt werden, dass einige der im Handel erhältlichen OSB und auch Leimhölzer eine Bewertung nach dem AgBB-Schema aufgrund von zu hohen Aldehyd- und Terpenemissionen nicht bestehen. Für die Aldehydemissionen (insbesondere Hexanal und ungesättigte höhere Aldehyde) konnte durch den Einsatz von Antioxidantien bei der OSB-Herstellung eine Verminderung auf ein Drittel erreicht werden, allerdings stiegen dadurch die Terpenemissionen an. In this project, eight Oriented Strand Boards (OSB) and seven plywood boards from DIY stores were tested in emission test chambers according to the AgBB scheme’s specifications. In addition, 17 OSBs manufactured in a pilot plant were tested to investigate the effect of production parameters on VOC emission. The use of antioxidants in OSB production was also tested. The main objective of the investigation was to find potential solutions for reducing VOC emissions from timber materials. The emissions from pine wood were investigated on six sapwood or heartwood samples from different trunk sections of freshly felled pine. The project’s results show that, due to their high aldehyde and terpene emissions, some types of commercially available OSB and plywood did not meet the AgBB scheme’s requirements. By using antioxidants in OSB production it was possible to reduce aldehyde emissions (especially hexanal and unsaturated higher aldehydes) to one third. However, this caused an increase in terpene emissions. KW - Bauprodukte KW - AgBB-Schema KW - Emissionsprüfkammern KW - Geruchsmessungen KW - VOC KW - VVOC KW - SVOC KW - Thermodesorption KW - GC/MS KW - Holzwerkstoffe KW - OSB KW - Leimholz KW - Construction products KW - AgBB Scheme KW - Emission test chamber KW - Odour measurement KW - Thermal desorption KW - Wood Products KW - Oriented Strand Board KW - Plywood Board PY - 2012 UR - http://www.umweltbundesamt.de/publikationen/emissionsverhalten-von-holz-holzwerkstoffen IS - 07 SP - 1 EP - 224 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-25843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, Birgit A1 - Brandt, Simone A1 - Badura, André A1 - Knigge, Anton A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Geruchs- und emissionsarme Produkte für eine gesunde Innenraumluft - Entwicklung von Anforderungen für den Blauen Engel bei innenraumrelevanten, großflächigen Produkten N2 - Gerüche in Innenräumen können belästigend wirken und das Wohlbefinden sowie die Gesundheit beeinflussen. Hauptziel der Untersuchungen ist es zu prüfen, ob die Vergabekriterien des Blauen Engels für die Produktgruppen „Elastische Bodenbeläge“ (DE-UZ 120) und „Emissionsarme Bodenbeläge, Paneele und Türen aus Holz und Holzwerkstoffen für Innenräume“ (DE-UZ 176) um geruchsrelevante Aspekte ergänzt werden können. Dies ist erstrebenswert, da Untersuchungen in Vorgängerprojekten gezeigt haben, dass die gemessenen Emissionen untersuchter Produkte zwar abnehmen, die Geruchsbelastung jedoch in etwa gleichgeblieben ist. Die Ergebnisse der Untersuchungen zeigen, dass es möglich ist Anforderungen an den Geruch der Produkte zu stellen. Ferner wird untersucht und gezeigt, dass die bislang vorläufig festgelegte Schwelle einer empfundenen Intensität von 7 pi für die Zulassung von Bauprodukten gemäß Schema des Ausschusses zur gesundheitlichen Bewertung von Bauprodukten (AgBB) und Blauer Engel, als Beurteilungsmaßstab geeignet ist. Der im AgBB-Schema zugrunde gelegte Zusammenhang zwischen der geruchlichen Zumutbarkeit und der empfundenen Intensität kann mit den durchgeführten Messungen untermauert werden. Es kann gezeigt werden, dass bei Tests mit großen, ungeschulten Personengruppen etwa 70% der Probandinnen und Probanden Produkte mit einer empfundenen Intensität von bis zu 7 pi geruchlich als zumutbar empfinden. Zur Bewertung der empfundenen Intensität wird ein Vergleichsmaßstab verwendet. Die Einhaltung konstanter Bedingungen für die Temperatur und die relative Feuchte bei den Messungen ist von großer Bedeutung, da diese einen Einfluss auf die Messergebnisse haben. Daher werden Untersuchungen bei unterschiedlichen Temperaturen und relativer Luftfeuchte, die mit einer eigens dafür gebauten kleinen raumlufttechnischen Anlage eingestellt werden können, durchgeführt. Die Ergebnisse belegen, dass die Einhaltung konstanter Prüfbedingungen wichtig ist und zeigen deren Einfluss auf die Geruchwahrnehmung. In einem neuen Luftqualitätslabor der HTW Berlin können Innenräume unter standardisierten Bedingungen geprüft werden. Es werden vergleichende Messungen mit Emissionsprüfkammertests durchgeführt, um zu prüfen, ob ähnliche Ergebnisse erreicht werden können. Das Ziel ist es, die Räume später für sensorische Messungen mit verschiedenen Ausstattungen zu nutzen. Das Vorhaben baut auf den Ergebnissen der Vorhaben UBA Texte 35/2011 „Sensorische Bewertung der Emissionen aus Bauprodukten – Integration in die Vergabegrundlagen für den Blauen Engel und das Bewertungsschema des Ausschusses zur gesundheitlichen Bewertung von Bauprodukten“ (Müller, 2011) und UBA Texte 92/2019 „Emissions- und geruchsarme Bauprodukte für energieeffiziente Gebäude – Entwicklung von Anforderungen und Konzepten für den Blauen Engel aus Klimaschutzsicht“ (Müller, 2019) auf. KW - Emission KW - Indoor air quality KW - VOC KW - Geruch KW - Bauprodukte PY - 2025 DO - https://doi.org/https://doi.org/10.60810/openumwelt-7610 SN - 1862-4804 VL - 78/2025 SP - 1 EP - 214 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-63341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Jann, Oliver A1 - Rockstroh, Jens A1 - Wilke, Olaf A1 - Noske, Reinhard A1 - Brödner, Doris A1 - Schneider, Uwe A1 - Horn, Wolfgang T1 - Entwicklung einer Prüfmethode und Untersuchungen zur Begrenzung von Emissionen aus Druckern und Kopiergeräten im Rahmen der Umweltzeichenvergabe (Forschungsbericht 201 95 311/02 / UBA-FB 000510) N2 - An neun verschiedenen Hardcopygeräten wurden in unterschiedlichen Emissionsmesskammern (zwei verschiedene 1 m³ - Kammern und eine 20 m³ - Kammer) in Kombination mit geeigneten Probenahme- und Analysenverfahren Untersuchungen zum Emissionsverhalten dieser Geräte hinsichtlich Staub, Ozon und VOC (TVOC) durchgeführt. Luftprobenahme und Analytik erfolgten für VOC mittels Tenax TA und anschließender Thermodesorption (TDS) in Verbindung mit GC / MS. Ozon wurde kontinuierlich bestimmt. Der Ozonanalysator arbeitete auf der Grundlage der flammenlosen Reaktion von Ozon mit Ethylen nach dem Prinzip der Chemilumineszenz. Die Staubbestimmung erfolgte gravimetrisch mittels Glasfaserfilter und Ultramikrowaage. Zusätzlich wurde die Partikelemission während des Druckbetriebes mit einem Partikelzähler bestimmt. Aufgrund der technischen Rahmenbedingungen standen nur kurze Druckzeiten von maximal 36 Minuten zur Verfügung. Um die Gleichgewichtskonzentration in der Prüfkammer zu erreichen, wurde die Luftaustauschrate in den 1 m³ - Kammern auf n = 4,0 bis 4,7 pro Stunde erhöht. Zusätzlich zur Prüfung in den Emissionsmesskammern sind verschiedene Papiere mittels Direkt - TDS sowie unterschiedliche Toner mittels Headspaceprobenahme in Kombination mit GC / MS hinsichtlich ihres Emissionsverhaltens untersucht worden. Für die untersuchten Geräte wurden Emissionsraten ermittelt. Sie betrugen für TVOC 0,41 bis 22,4 mg pro Stück und Stunde, für Ozon kleiner 0,02 bis 4,6 mg pro Stück und Stunde sowie für Staub 0,10 bis 7,63 mg pro Stück und Stunde. Verglichen mit Frischfaserpapier wurden bei den Untersuchungen mit Recyclingpapier deutlich höhere SVOC - Konzentrationen nachgewiesen. Im Ergebnis der Untersuchungen wurde ein Prüfverfahren entwickelt, das die Basis für Emissionsmessungen im Rahmen der Umweltzeichen RAL –UZ 62, RAL –UZ 85 sowie des neuen RAL –UZ 114 für Multifunktionsgeräte darstellt. KW - Emissionen KW - VOC KW - Ozon KW - Staub KW - Hardcopygerät KW - Drucker KW - Kopierer KW - Emissionsmesskammer KW - Umweltzeichen PY - 2003 UR - http://www.umweltbundesamt.de/publikationen/entwicklung-einer-pruefmethode-untersuchungen-zur SN - 1862-4804 SN - 0722-186X IS - 71 SP - 1 EP - 159 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-7276 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Däumling, C. A1 - Brenske, K.-R. A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Health-related evaluation procedure of VOC and SVOC emissions from building products - a contribution to the European construction products directive KW - VOC KW - SVOC KW - Bauprodukte KW - AgBB KW - Bewertung PY - 2005 UR - http://www.technikwissen.de/gest/article.php?data[article_id]=7141 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 65 IS - 3 SP - 90 EP - 92 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-7364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Burbiel, M. A1 - Wilke, Olaf A1 - Kalus, Sabine ED - Levin, H. T1 - Biocide emissions from materials into indoor air N2 - The European biocides directive (98/8/EG) demand the control of emissions into the envi-ronment like soil, water and air. In this study a method for measuring the input of biocides into the indoor air from materials should be developed. The emission of two products containing biocides (plastic foil, wool carpet) and six different types of biocide containing formulations applied on wood or ceramic tiles were investigated in 20 or 23 l glass emission chambers. Each chamber test was performed over a period of 100 up to 200 days. SVOC show totally different emission curves in chamber tests compared to volatile organic com-pounds (VOC). They reach their maximum value after some days or weeks. Thus a period of 3 months is sometimes necessary for exact measurements. Area specific emission rates (SERa in µg/m²h) for permethrin (0.006), propiconazole (0.2), dichlofluanid (1.5), tolylfluanid (1.2), octylisothiazolinone (2.5) and for iodpropinylbutyl-carbamat (1.7) were determined. T2 - 9th International Conference on Indoor Air Quality and Climate CY - Monterey, CA, USA DA - 2002-06-30 KW - SVOC KW - Biocide KW - Chamber test KW - Polyurethane foam KW - Testing method PY - 2002 UR - http://www.irbnet.de/daten/iconda/CIB6909.pdf SN - 0-9721832-0-5 VL - 2 SP - 926 EP - 930 PB - International Academy of Indoor Air Sciences CY - Santa Cruz, Calif. AN - OPUS4-2000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris ED - Levin, H. T1 - VOC- and SVOC-Emissions from Adhesives, Floor Coverings and Complete Floor Structures N2 - VOC/SVOC-Emissions from materials for flooring installation (primer, screed, adhesive, floor covering) were measured by means of emission test chambers and cells over a time period of at least 28 days at 23 C, 50 % relative humidity and an area specific air flow rate of q = 1.25 m³/m²h. Single components were tested in comparison to three complete structures (same concrete, primer, screed, adhesive) with different types of floor covering (PVC, carpet, linoleum). Sorption into concrete/screed and different sealing by the flooring materials affected the emissions from the complete structures. The complete structures with linoleum and PVC showed the same emissions and emission rates as the flooring materials alone. Emissions from the carpet-covered structure resulted mainly from the lower layers. For two adhesives the formation of secondary emissions (aldehydes and organic acids) was observed starting after the standard testing time of 28 days. T2 - 9th International Conference on Indoor Air Quality and Climate CY - Monterey, CA, USA DA - 2002-06-30 KW - Test chambers KW - VOCs and SVOCs KW - Secondary emissions KW - Construction and renovation PY - 2002 UR - https://www.irbnet.de/daten/iconda/CIB6472.pdf SN - 0-9721832-0-5 VL - 1 SP - 962 EP - 967 PB - International Academy of Indoor Air Sciences CY - Santa Cruz, Calif. AN - OPUS4-2002 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jann, Oliver A1 - Wilke, Olaf T1 - Möglichkeiten und Grenzen bei der Bestimmung von SVOC-Emissionen aus Materialien und Produkten T2 - Messtechnisches Kolloquium CY - Schwäbisch Gmünd, Deutschland DA - 2002-06-11 PY - 2002 SN - 3-18-091656-7 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 1656 SP - 357 EP - 367 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-2126 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jann, Oliver A1 - Köppke, J. A1 - Lehmann, R. A1 - Schneider, Uwe T1 - Messungen der Radonexhalation aus Baustoffen unter Modellklimabedingungen PY - 2003 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 63 IS - 1/2 SP - 49 EP - 52 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-2279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - Untersuchung und Ermittlung emissionsarmer Klebstoffe und Bodenbeläge N2 - Im vorliegenden Bericht wurden 11 Fußbodenbelagskleber, eine Grundierung, eine Spachtelmasse, 14 Teppiche, 5 PVC-Bodenbeläge, drei Linoleum-Beläge, ein Kautschukbelag und ein Polyolefinbelag über einen Zeitraum von mindestens 28 Tagen mittels Prüfkammer- bzw. Prüfzellenmessung auf ihr Emissionsverhalten untersucht. Die Emissionsmessungen an den Einzelmaterialien Kleber und Bodenbelag sollten die möglichen Emissionen (Substanzen und Konzentrationen) und deren zeitlichen Verlauf ermitteln. Außerdem wurden die Emissionen aus 7 Materialkombinationen ermittelt. Dazu gerhörten drei Komplettaufbauten aus Estrich, Grundierung, Spachtelmasse und Kleber mit den Belägen Teppich, PVC und Linoleum sowie 4 Verbundsysteme. Dies waren: Verbundsystem Estrich/Grundierung/Spachtelmasse/Kleber, Verbundsystem Glasplatte/Kleber/Teppich, Verbundsystem Glasplatte/Kleber/PVC-Belag und das Verbundsystem Estrich/Kleber. Die Emissionen aus den Komplettbauten wueden durch Sorptionseffekte und durch die unterschiedliche Durchlässigkeit der Bodenbeläge beeinflusst. Dabei waren die Emissionen aus den Komplettaufbauten und Verbundsystemen jeweils geringer als die Summe der Emissionen der entsprechenden Einzelmaterialien. Ergänzende Untersuchungen wurden durchgeführt zur Vergleichbarkeit der Emissionsmessungen in unterschiedlichen Prüfkammern (Volumen 1 m3 und 0,02 m3) bzw. Messzellen(Volumen 1 l und 0,035 l [FLEC]). und bei 42 Klebern zur Anwendbarkeit der Direkt-Thermodesorption (dynamische Headspace-Methode) als Screening-Verfahren. Des weiteren wurden Versuche durchgeführt, um die Auswirkungen unterschiedlicher Probenherstellung (Trägermaterial, Auftragsmenge, Auftragsart) auf die Emissionen aus den Fußbodenklebern abschhätzen können. Die durchgeführten Untersuchungen stellen eine Grundlage zur Erarbeitung eines Umweltzeichens für Fußbodenkleber dar. KW - Kleber KW - Fußbodenbelagskleber KW - Verlegewerkstoffe KW - Bodenbeläge KW - Emissionen KW - VOC KW - SVOC KW - Emissionsmesskammern KW - Emissionsmesszelle PY - 2003 UR - http://www.umweltbundesamt.de/publikationen/untersuchung-ermittlung-emissionsarmer-klebstoffe SN - 0722-186X IS - 27 SP - 1 EP - 144 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-2902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Wilke, Olaf T1 - Suitability of small environmental chambers to test the emission of biocides from treated materials into the air N2 - Biocides are used to protect materials that might be damaged by fungal, microbial or insect activity. The aim of this study is to develop a method for the measurement of these organic compounds, which generally have low or moderate vapor pressures. The biocides considered in this study are permethrin, dichlofluanid, tolylfluanid, iodpropinylbutylcarbamat, octylisothiazolinone, tebuconazole and propiconazole. The emission from two commercial products (plastic foil, wool carpet) containing biocides and of seven types of biocidal formulations applied to wood or clay tiles were investigated in 20-l glass emission test chambers. Each chamber test was performed over a period of 100–200 days, and one investigation was conducted over several years. Compared to volatile organic compounds, low-volatility compounds show totally different emission curves in chamber tests; maximal emission values may be reached in days or weeks. A period of 3 months is sometimes necessary for the determination of area-specific emission rates (SERa's). The SERa's (?g m-2 h-1) from biocide-containing products were determined for permethrin (0.006), propiconazole (0.3), dichlofluanid (2.0), tolylfluanid (1.0), octylisothiazolinone (2.5) and iodpropinylbutylcarbamat (2). In most cases, the SERa stayed at its maximum value or declined slowly over the test period. Additionally, a chamber test begun in 1994 with a piece of wood treated with a typical mixture of biocides dissolved in a technical solvent was continued. SERa's (?g m-2 h-1) for dichlofluanid (0.20), tebuconazole (0.49) and permethrin (0.08) remained detectable after the period of nearly 9 years during which the sample remained continuously in the chamber. This test proved the very slow decrease of emission of low-volatility compounds like permethrin and tebuconazole. KW - Indoor air KW - Biocides KW - Emission test chamber KW - SVOC PY - 2003 DO - https://doi.org/10.1016/j.atmosenv.2003.09.024 SN - 0004-6981 SN - 1352-2310 VL - 37 IS - 39-40 SP - 5477 EP - 5483 PB - Elsevier CY - Amsterdam AN - OPUS4-2676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Torge, Manfred A1 - Müller, Wolfgang A1 - Jann, Oliver A1 - Brödner, Doris A1 - Wilke, Olaf A1 - Pilz, M. T1 - Schadstoffbelastungen in Ausstellungsvitrinen und Simulation der Bedingungen im Labor T2 - 28. Jahrestagung der GUS CY - Pfinztal bei Karlsruhe, Deutschland DA - 1999-03-10 KW - Kulturguterhaltung KW - Umweltsimulation PY - 1999 SN - 3-9806167-3-8 SP - 16-1-16-14 CY - Pfinztal AN - OPUS4-3233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rockstroh, Jens A1 - Rühl, Hellmuth A1 - Jann, Oliver T1 - Entwicklung einer umweltverträglichen Holzklebetechnik durch den Einsatz von Proteinbindemitteln T2 - 8. Symposium Nachwachsende Rohstoffe für die Chemie CY - Tübingen, Deutschland DA - 2003-03-26 PY - 2003 SN - 3-7843-3237-4 N1 - Serientitel: Schriftenreihe nachwachsende Rohstoffe – Series title: Schriftenreihe nachwachsende Rohstoffe IS - 22 SP - 567 EP - 571 PB - Landwirtschaftsverl. CY - Münster AN - OPUS4-2649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Wiegner, Katharina A1 - Jann, Oliver A1 - Bremser, Wolfram A1 - Brödner, Doris A1 - Kalus, Sabine A1 - Juritsch, Elevtheria A1 - Till, Carola T1 - Untersuchungen zur Verbesserung der Messung von flüchtigen organischen Verbindungen aus Fußbodenbelägen im Rahmen der gesundheitlichen Bewertung von Bauprodukten T1 - Investigations for the improvement of the measurement of volatile organic compounds from floor coverings within the health-related evaluation of construction products N2 - In den Grundsätzen des DIBt zur gesundheitlichen Bewertung von Bauprodukten in Innenräumen ist das Bewertungsschema des Ausschusses zur gesundheitlichen Bewertung von Bauprodukten (AgBB-Schema) als wesentliche Grundlage enthalten. Dieses Schema bewertet die mit Hilfe einer Prüfkammermessung bestimmten Emissionen von flüchtigen und schwer flüchtigen organischen Verbindungen (VOC und SVOC). Die Prüfkammer dient dabei der Einhaltung standardisierter Klimabedingungen (Temperatur 23°C, relative Luftfeuchtigkeit 50 %) sowie der Einstellung bestimmter Prüfparameter wie Luftwechselrate und Beladungsfaktor. Die Anforderungen an eine Prüfkammer sind in DIN EN ISO 16000-9 beschrieben. Die Analytik und Quantifizierung der VOC geschieht mittels Tenax-Thermodesorption und nachfolgender Gaschromatographie gekoppelt mit Massenspektrometrie und ist in DIN ISO 16000-6 beschrieben. Probenahmen werden am 3. und 28. Tag der Prüfkammermessung durchgeführt. Am dritten Tag erfolgt eine Bewertung der Emissionen aus dem Bauprodukt anhand des TVOC-Wertes und der Summe der detektierten cancerogenen Stoffe (nach 67/548/EWG, Einstufung als cancerogen der Kategorie 1 und 2). Ein Produkt erfüllt die Kriterien, wenn der TVOC-Wert nach 3 Tagen nicht größer als 10 mg/m³ ist und die Summe der Cancerogene 10 μg/m³ nicht übersteigt. Am 28. Tag wird zusätzlich zum TVOC-Wert und den Cancerogenen die Emission von SVOCs berücksichtigt und eine Einzelstoffbewertung anhand von NIK-Werten vorgenommen. Der TVOC-Wert nach 28 Tagen darf nicht größer als 1 mg/m³ sein, die Summe der Cancerogenen nicht größer als 1 μg/m³. Die Summe an SVOCs darf eine Konzentration von 0,1 mg/m³ nicht überschreiten. Der sogenannte R-Wert, die Summe aller Quotienten aus Einzelstoffkonzentration und dem NIK-Wert des Einzelstoffes, darf einen Wert von 1 nicht übersteigen. Außerdem darf die Summe von Substanzen, die keinen NIK-Wert besitzen, nicht größer als 0,1 mg/m³ sein. Der Ringversuch, der im Rahmen der Untersuchungen zur Verbesserung der Prüfkammermessungen durchgeführt wurde, hatte vor allem den Zweck, den Einfluss unterschiedlicher Methodenparameter bei der Prüfkammermessung in unterschiedlichen Prüflaboratorien zu erfassen. Anhand der Ergebnisse sollte eine Ursachenforschung für die großen Abweichungen der bisher durchgeführten Ringversuche erfolgen. Durch die drei aufeinander aufbauenden Schritte sollte der Einfluss der Analytik, der Probenahme und der Prüfkammer geklärt werden. Der Ringversuch diente nicht der Anerkennung der teilnehmenden Prüflaboratorien im Bereich der Bauproduktenprüfung für eine DIBt-Zulassung. Ausgehend von den Prüflaboratorien, die in der Projektgruppe „Prüf- und Messverfahren zur gesundheitlichen Bewertung von Bauprodukten“ des DIBt mitarbeiteten, wurde der Kreis auf europäische Prüflaboratorien erweitert, die sich ebenfalls mit Prüfkammermessungen an Bauprodukten beschäftigen. Dazu erging ein Einladungsschreiben an alle von vorangegangenen Ringversuchen bekannten Teilnehmer. Insgesamt ergab sich ein Teilnehmerkreis von 29 Instituten, davon 16 aus Deutschland, jeweils zwei aus Österreich, Belgien, Schweden, Dänemark und jeweils eins aus Finnland, Großbritannien, Frankreich, Italien und Portugal. Vor Beginn des Ringversuches waren davon 11 im Zulassungsbereich tätig. Zur wissenschaftlichen Begleitung wurde durch das DIBt ein Betreuergremium einberufen. In zwei Sitzungen (April und November 2007) wurden die aktuellen Ergebnisse vorgestellt und diskutiert sowie die weitere Vorgehensweise besprochen. Eine Abschlussveranstaltung nach der Auswertung des dritten Schrittes des Ringversuches fand im April 2008 im DIBt statt. Dazu waren alle Teilnehmer eingeladen. Für die Emissionsmessung von flüchtigen organischen Verbindungen (VOC) aus Materialien mit Hilfe von Emissionsprüfkammern sind bisher nur wenige Ringversuche durchgeführt worden (De Bortoli et al. 1999; Jann et al. 2000; Hansen et al. 2000; Oppl and Winkels 2002; Windhövel and Oppl 2005; Kirchner 2007; Oppl 2008). Dabei zeigten sich meist große Streuungen der Ergebnisse. Ein großes Problem für die Durchführung solcher Ringversuche ist das Fehlen von Referenzmaterialien mit bekannter Emissionsrate von Zielsubstanzen. Deshalb orientiert man sich für die Auswertung solcher Ringversuche am Mittelwert aller Ergebnisse. Dafür ist die Homogenität des Testmaterials von größter Bedeutung. Diese wurde in früheren Ringversuchen nicht wirklich sichergestellt. Im hier beschriebenen Forschungsprojekt wurde auf die Homogenität des Probenmaterials besonderen Wert gelegt. Der gesamte Ringversuch wurde in drei Schritte unterteilt. Die einzelnen Schritte wurden dabei von Schritt zu Schritt immer komplexer. Im ersten Schritt erfolgte die Analyse von flüssigen Lösungen, im zweiten die Bestimmung von VOCs in Prüfkammerluft und im dritten Schritt erfolgte eine komplette Emissionsprüfkammermessung bei den Teilnehmern. N2 - In the German Institute for Construction Technology’s (DIBt) principles for the health assessment for construction products used in interiors, the Evaluation procedure of the Committee for Health-related Evaluation of Building Products (AgBB Scheme) is contained as a substantial base. This scheme evaluates the emissions of volatile and semivolatile organic compounds (VOC and SVOC), determined by test chamber measurements. Within the interlaboratory comparison, which was divided into three steps, the emission test method from building products was checked against the principles of health-related evaluation of construction products in indoor spaces (based on DIN EN ISO 16000-9 together with DIN ISO 16000-6) with the co-operation of 29 European test institutes. The objective was to assess the comparability of the test method carried out in different test Chambers and using different thermodesorption devices. In the first step the analysis of liquid solutions took place to observe the influence of the analysis itself. In the second step VOCs were sampled in the air of a BAM test chamber onto tubes from the participants for the Analysis by them. In the third step a complete Emission test chamber measurement was carried out by the participants. A major problem for the execution of such interlaboratory comparisons is the lack of reference materials. Therefore the homogeneity of the test material was of great importance. As a result of the first step (analysis of 4 liquid solutions) a standard deviation of less than 20 % for 8 out of 11 substances tested was obtained. The Standard deviations for dichloropropanol, caprolactam and Butyl diglycol ranged up to 36 %. The second step, which included air sampling at a BAM test chamber, resulted in only one standard deviation value less than 20 % (11 % for styrene). The standard deviations for the other six substances were between 20 % and 36 %. For step 3 a sealant was chosen instead of the flooring material for homogeneity reasons. In step 3 the standard deviations for 4 of the 7 measured VOC concentrations from two chamber tests were between 17 % and 19 % and thus within the same range as in Step 1 and even better than for most substances in Step 2. A Standard deviation of 60 % was found for the key component ethanediol, but this can be explained with the difficult analysis method for this substance. A second objective of the project was to formulate criteria against which the specialist competence of the test institutes for emission tests can be checked and based on the principles for the health assessment for construction products used in interior. For this purpose a catalogue of criteria has been developed, which is divided into three parts. In the first part, basic requirements are formulated such as impartiality, accreditation for test chamber measurements, verification of experience by participation in earlier interlaboratory comparisons and the laboratory equipment. The second part requires the test-specific proof in the form of successful participation in interlaboratory comparisons organised by BAM biannually. The third part instructs the laboratories that they must ensure they are always upto-date both in terms of their knowledge and the available equipment. The quality assurance for the knowledge is ensured by regular participation in the exchanging of experience between the test laboratories. In terms of technical requirements the test institutes must be willing to successfully participate in at least one interlaboratory comparison per year. The present interlaboratory comparison was not designed to recognise the participating test laboratories in the field of the construction product testing for a DIBt approval. KW - Ringversuch KW - Laborvergleich KW - VOC-Emissionen KW - Kammermessungen KW - Round robin KW - Inter laboratory study KW - VOC emissions KW - Emission test chamber PY - 2009 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-198380 UR - https://www.baufachinformation.de/buch/Untersuchungen-zur-Verbesserung-der-Messung-von-fl%C3%BCchtigen-organischen-Verbindungen-aus-Fu%C3%9Fbodenbel%C3%A4gen-im-Rahmen-der-gesundheitlichen-Bewertung-von-Bauprodukten/230803 SN - 978-3-8167-8100-4 N1 - Sprachen: Deutsch/Englisch - Languages: German/English IS - T 3217 SP - 1 EP - 206 PB - Fraunhofer IRB Verl. CY - Stuttgart AN - OPUS4-19838 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rockstroh, Jens A1 - Jann, Oliver A1 - Wilke, Olaf A1 - Noske, Reinhard A1 - Brödner, Doris A1 - Schneider, Uwe A1 - Horn, Wolfgang ED - Wai, T. K. ED - Sekhar, C. ED - Cheong, D. T1 - Investigations on VOC, ozone and dust emissions from hardcopy devices (laser printers, copiers and multifunctional devices) in test chambers - development of a test method T2 - 7th Healthy Buildings Conference ; HB 2003 ; ISIAQ international conference CY - Singapore, Republic of Singapore DA - 2003-12-07 KW - Emissions KW - Printers KW - Copiers KW - VOC KW - Dust KW - Ozone KW - Blue Angel PY - 2003 SN - 981-049974-4 VL - 1 SP - 397 EP - 403 CY - Singapore AN - OPUS4-3315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris ED - Wai, T. K. ED - Sekhar, C. ED - Cheong, D. T1 - VOC and SVOC Contribution of Papers for Hardcopy Devices to Indoor Air Pollution T2 - 7th Healthy Buildings Conference ; HB 2003 ; ISIAQ international conference CY - Singapore, Republic of Singapore DA - 2003-12-07 PY - 2003 SN - 981-049974-4 VL - 1 SP - 289 EP - 295 CY - Singapore AN - OPUS4-3377 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - Emissionsmessungen an Materialien für Fußbodenaufbauten T2 - Kolloquium Luftverunreinigungen im Innenraum CY - Düsseldorf, Deutschland DA - 2003-11-03 PY - 2003 SN - 3-18-091778-4 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 1778 SP - 71 EP - 82 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-3378 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - VOC- und SVOC-Emissionen aus Fußbodenaufbauten und den dafür verwendeten Materialien PY - 2003 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 63 IS - 3 SP - 92 EP - 98 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-2302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Torge, Manfred A1 - Jann, Oliver A1 - Pilz, M. T1 - Das Simulieren von Schadstoff- und Klimabelastungen KW - Kulturguterhaltung KW - Umweltsimulation PY - 2000 SN - 0933-4017 VL - 106 IS - 6 SP - 436 EP - 441 PB - Callwey CY - München AN - OPUS4-3235 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - VOC- and SVOC-Emissions from Adhesives, Floor Coverings and Complete Floor Structures N2 - Emissions of volatile organic compounds (VOC) and semivolatile organic compounds (SVOC) from materials for flooring installation (primer, screed, adhesive, floor covering) were measured by means of emission test chambers and cells over a time period of at least 28 days at 23 °C, 50% relative humidity and an area specific air flow rate of q = 1.25 m3/m2 h. Single components were tested in comparison to three complete structures (same concrete, primer, screed, adhesive) with different types of floor covering (PVC, carpet, linoleum). Sorption into concrete/screed and different permeability of flooring materials affected the emissions from the complete structures. The complete structures with linoleum and PVC showed the same types of emission and emission rates as the individual floor coverings themselves. Emissions from the carpet-covered structure resulted also from the lower layers. In all cases emissions from the complete structures were lower than the sum of emissions from the single components. For two adhesives the formation of secondary emissions (aldehydes and organic acids) was observed starting after the standard testing time of 28 days. PY - 2004 DO - https://doi.org/10.1111/j.1600-0668.2004.00314.x SN - 0905-6947 SN - 1600-0668 VL - 14 IS - Suppl. 8 SP - 96 EP - 105 PB - Danish Techn. Pr. CY - Copenhagen AN - OPUS4-5048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kemmlein, Sabine A1 - Rockstroh, Jens A1 - Jann, Oliver ED - Reichl, H. T1 - Investigation on emissions of volatile and semivolatile compounds (VOC, SVOV), dust and ozone from electronic consumer products T2 - Joint International Congress and Exhibition Electronics Goes Green 2004+ CY - Berlin, Germany DA - 2004-09-06 KW - Emission test chamber KW - Emission test cells KW - VOC KW - SVOC KW - Flame retardants KW - Ozone KW - Dust KW - Hardcopy devices KW - Electronics PY - 2004 SP - 1051 EP - 1052 PB - Fraunhofer IRB Verl. CY - Stuttgart AN - OPUS4-5047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gehr, V. A1 - Jann, Oliver A1 - Söffge, M. A1 - Wilke, Olaf T1 - Emissionen von flüchtigen organischen Verbindungen aus Recyclingpapieren und ihre Relevanz für die Innenraumluftqualität PY - 2004 SN - 0043-7131 VL - 132 IS - 17 SP - 1010 EP - 1014 PB - Dt. Fachverl. CY - Frankfurt, M. AN - OPUS4-5205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - Höheres Emissionspotenzial bei Recyclingpapieren PY - 2004 SN - 0344-1733 SN - 1610-8256 VL - 28 SP - 54 EP - 56 PB - Vogel CY - Würzburg AN - OPUS4-5202 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rockstroh, Jens A1 - Jann, Oliver A1 - Wilke, Olaf A1 - Noske, Reinhard A1 - Brödner, Doris A1 - Kalus, Sabine A1 - Schneider, Uwe A1 - Krocker, Christian A1 - Horn, Wolfgang T1 - Emissionsbegrenzung aus Laserdruckern und Kopierern N2 - Vor dem Hintergrund der notwendigen Revision der Kriterien zur Vergabe des Gütezeichens "Blauer Engel" für Laserdrucker, Kopierer und Multifunktionsgeräte mussten auch die Prüfmethoden angepasst werden, da die alten Verfahren nicht mehr die heutigen Anforderungen der Emissionsmessung erfüllen. In diesem Zusammenhang wurde auch das unterschiedliche Emissionsverhalten von Hardcopy-Geräten auf Grund der verschiedenen und nicht miteinander vergleichbaren Prüfverfahren heftig diskutiert. Aus diesen Gründen wurde ein neues Prüfverfahren entwickelt, mit dem eine verlässliche und reproduzierbare Prüfung der Emissionsraten von Staub, Ozon und flüchtiger organischer Verbindungen auf der Basis des ECMA (European Computer Manufacturer Association) Standards 328 möglich ist. Dazu wurden neun verschiedene Geräte unter verschiedenen Bedingungen untersucht. Als ein Ergebnis dieser Studie wurden neue Kriterien zur Vergabe des "Blauen Engels" für Kopierer, Drucker und Multifunktionsgeräte festgelegt. PY - 2004 DO - https://doi.org/10.3139/120.100606 SN - 0025-5300 VL - 46 IS - 9 SP - 465 EP - 471 PB - Carl Hanser Verlag CY - München AN - OPUS4-4120 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Sachstand Geruchsmessung und -beurteilung T2 - 2. AgBB-Fachgespräch zur Vorhehensweise bei der gesundheitlichen Bewertung der Emissionen von flüchtigen organischen Verbindungen (VOC) aus Bauprodukten, DIBt CY - Berlin, Germany DA - 2004-11-25 PY - 2004 AN - OPUS4-4776 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Brödner, Doris T1 - Direkte thermische Extraktion versus Prüfkammer - Emissionsverhalten von Teppichklebstoffen sicher bestimmen PY - 2004 UR - http://www.gerstel.de/pdf/GERSTEL_Aktuell_32_4-5_de.pdf IS - 32 SP - 4 EP - 5 CY - Mülheim an der Ruhr AN - OPUS4-3498 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schoknecht, Ute A1 - Wegner, R. A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Emission of Biocides from Treated Materials N2 - Methods for the determination of biocide emissions from treated materials into water and air were developed and tested in order to support a comparative ecological assessment of biocidal products. Leaching tests, experiments with simulated rain, extraction cleaning of carpets and emission chamber tests were performed with a series of treated materials. The experiments focused on the effect of changes in the procedure as well as characteristics of the specimens and demonstrate the suitability of the proposed methods for biocides of different product types. It was demonstrated that emissions of biocides into water can be compared on the basis of leaching tests in which the emission kinetics of the active ingredients are recorded. However, the water volume per surface area and the timetable for water changes have to be defined in such tests. Functions of flux rates related to time can be well described for inorganic compounds, whereas modelling of the data is more complicated for organic substances. Emission chamber tests using 20-litre and 23-litre glass exsiccators, originally developed to study volatile organic compounds, were successfully adapted for the investigation of the emission of biocides from treated materials which are usually semi volatile organic compounds. However, test parameters and the method of analysis have to be adapted to the substances to be determined. Generally, it was found that the emission curves for the semi volatile organic compounds investigated differ from those of volatile organic compounds. KW - Air KW - Biocidal products KW - Biocides KW - Biocides directive KW - Emission KW - Emission test chambers KW - Environmental exposure assessment KW - Leaching procedure KW - Simulated rain KW - SVOC KW - Test procedures KW - VOC KW - Water KW - Wood preservatives PY - 2003 SN - 0944-1344 SN - 1614-7499 VL - 10 IS - 3 SP - 154 EP - 161 PB - Ecomed Publ. CY - Landsberg AN - OPUS4-5492 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Möglichkeiten und Grenzen bei der Bestimmung von SVOC-Emissionen aus Materialien und Produkten T2 - VDI-Kolloquium "Neuere Entwicklungen bei der Messung und Beurteilung der Lüftqualität" CY - Schwäbisch Gmünd, Germany DA - 2002-06-11 PY - 2002 AN - OPUS4-5931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Prüfkammerverfahren zur Bestimmung der Emmision flüchtiger organischer Verbindungen aus Materialien und Produkten T2 - BAM -Sonderkolloquium "Bestimmung der Messunsicherheit - Erfahrungen und Beispiele" CY - Berlin, Germany DA - 2002-11-01 PY - 2002 AN - OPUS4-5930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emmisionen aus Materialien und Produkten - Aufgaben und Methodik T2 - Beratungskreis für die Abteilung I "Analytische Chemie; Referencematerialien", BAM CY - Berlin, Germany DA - 2002-05-08 PY - 2002 AN - OPUS4-5867 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kemmlein, Sabine A1 - Bergmann, Meike A1 - Jann, Oliver T1 - Probenaufbereitungs- und Analyseverfahren für Flammschutzmittel (Pentabromdiphenylether, Octabromdiphenylether) in Erzeugnissen (Forschungsbericht 202 67 300 / UBA-FB 000839) N2 - Im Rahmen der Richtlinie 2003/11/EG zur 24. Änderung der Richtlinie 76/769/EWG wurde ein Grenzwert von 0,1 Gewichts-% für penta- und octabromierte Diphenylether in Erzeugnissen festgelegt. Zur Überprüfung dieses Grenzwertes wurde ein Standardanalyseverfahren zur quantitativen Bestimmung von ausgewählten Pentabromdiphenylethern (PentaBDE-Isomere) und Octabromdiphenylethern (OctaBDE-Isomere) in Polymeren mit Hilfe der Gaschromatographie-Massenspektrometrie (GC/MS) entwickelt. Zur Verfahrensentwicklung wurden folgende Isomere ausgewählt: BDE85 (2,2’,3,4,4’-PentaBDE), BDE99 (2,2’,4,4’,5- PentaBDE), BDE100 (2,2’,4,4’,6-PentaBDE), BDE203 (2,2’,3,4,4’,5,5’,6-OctaBDE), BDE196 (2,2’,3,3’,4,4’,5,6’-OctaBDE) und BDE197 (2,2’,3,3’,4,4’,6,6’-OctaBDE). Vorbereitend wurden folgende Modellpolymere hergestellt: Polyurethan (PUR-H) mit 0,1 Gew.-% Summe PentaBDEIsomere, Epoxidharz (EP) mit 0,1 Gew.-% Summe PentaBDE-Isomere, Polystyrol (PS) und Acrylnitril-Butadien-Styrol- Copolymer (ABS) mit jeweils 0,1 Gew.-% Summe OctaBDE-Isomere. Im Rahmen des Projektes wurde ein Ringversuch mit 18 Teilnehmern durchgeführt, bei dem die genannten Polymere dem Standardanalyseverfahren unterzogen wurden. Der Ringversuch wurde zwischen dem 01. Juni und 30. November 2004 veranstaltet. Die Datenauswertung erfolgte in Anlehnung an DIN ISO 5725-2:2002-12 „Genauigkeit (Richtigkeit und Präzision) von Messverfahren und Messergebnissen, Teil 2: Grundlegende Methode für die Ermittlung der Wiederhol- und Vergleichpräzision eines vereinheitlichten Messverfahrens“. Folgende Mittelwerte der Ermittlungsergebnisse sowie Standardabweichungen wurden bestimmt: 1,09 ± 0,16 mg g-1 (15 %) (Summe PentaBDE-Isomere/EP), 1,3 ± 0,19 mg g-1 (15 %) (Summe PentaBDE-Isomere/PUR-H), 0,99 ± 0,27 mg g-1 (27 %) (Summe OctaBDEIsomere/PS), 0,42 ± 0,11 mg g-1 (26 %) (Summe OctaBDE-Isomere/ABS). Als statistische Kennzahlen für das Standardanalyseverfahren wurde folgende Parameter ermittelt: Für PentaBDE-Isomere in EP wurde eine Wiederholstandardabweichung von srj = 0,044 mg g-1 (4,0 %) und eine Vergleichstandardabweichung sRj = 0,167 mg g-1 (15 %) bestimmt. Für PentaBDE-Isomere in PUR-H ergab sich für srj = 0,038 mg g-1 (2,9 %) und sRj = 0,195 mg g-1 (15 %). Für OctaBDE-Isomere in ABS ergab sich für srj = 0,029 mg g-1 (6,9 %) und sRj = 0,114 mg g-1 (27 %) und für OctaBDE-Isomere in PS srj = 0,043 mg g-1 (4,3 %) und sRj = 0,255 mg g-1 (26 %). KW - Pentabromdiphenylether (PentaBDE) KW - Octabromdiphenylehter (OctaBDE) KW - Polymer KW - Vergleichspräzision KW - Wiederholpräzision KW - Richtlinie 2003/11/EG KW - Richtlinie 76/769/EWG KW - GC/MS KW - Polybromierte Flammschutzmittel PY - 2005 SN - 1862-4804 SN - 0722-186X IS - 23 SP - 1 EP - 152 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-10848 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Horn, Wolfgang A1 - Gellert, R. A1 - Jann, Oliver A1 - Kalus, Sabine A1 - Brödner, Doris T1 - Emission tests on thermal insulation products with the intention to implement these tests into EN standards T2 - Indoor Air 2005 CY - Beijing, PR China DA - 2005-09-04 KW - Bauprodukte KW - Emissionen KW - Dämmstoffe KW - Kammerverfahren KW - VOC KW - EN-Standards KW - Insulation material KW - VOC emission KW - Chamber copmparison KW - Construction products directive KW - AgBB-scheme PY - 2005 SN - 7-89494-830-6 IS - 2 SP - 1886 EP - 1890 PB - Tsinghua University Press CY - Beijing AN - OPUS4-7612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionsmessungen an Materialien mit Hilfe von Prüfkammern sowie direkter thermischer Extraktion T2 - Gerstel-Anwenderseminare Frühjahr 2005 CY - Potsdam, Germany DA - 2005-06-01 PY - 2005 AN - OPUS4-7591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kemmlein, Sabine A1 - Bergmann, Meike A1 - Jann, Oliver T1 - Standard measurement method for the determination of polybrominated flame retardants (pentabromo diphenylether, octabromo diphenylether) in products (Research Report 202 67 300 / UBA-FB 000839/e) N2 - In accordance with the Directive 2003/11/EC amending the Council Directive 76/769/EEC for the 24th time, pentabromo and octabromo diphenylethers may not be used or put on the market in concentrations higher than 0.1 % by mass. To verify this threshold value a standard measurement method for the determination of selected pentabromo diphenylethers (pentaBDE-isomers) and octabromo diphenylethers (octaBDE-isomers) in polymers based on gas chromatography mass spectrometry (GC/MS) was developed. The following target compounds were selected for the investigations: BDE85 (2,2’,3,4,4’-pentaBDE), BDE99 (2,2’,4,4’,5- pentaBDE), BDE100 (2,2’,4,4’,6-pentaBDE), BDE203 (2,2’,3,4,4’,5,5’,6-octaBDE), BDE196 (2,2’,3,3’,4,4’,5,6’-octaBDE), BDE197 (2,2’,3,3’,4,4’,6,6’-OctaBDE). The following reference materials were prepared: polyurethane (PUR-H) and epoxy resin (EP) containing 0.1 % by mass of sum of pentaBDE isomers, polystyrene (PS) and acrylnitril-butadiene-styrenecopolymer (ABS) containing 0.1 % by weight of sum of octaBDE isomers. For quality assurance of the standard measurement method an interlaboratory comparison was conducted between 1 June and 30 November 2004 where 18 participants were involved. Data assessment was performed in accordance with DIN ISO 5725-2:2002-12 “Accuracy (trueness and precision) of measurement methods and results – Part 2: Basic methods for the determination of repeatability and reproducibility of a standard measurement method”. The following general mean values and standard deviations were obtained: 1.09 ± 0.16 mg g-1 (15 %) (sum pentaBDE isomers/EP), 1.3 ± 0.19 mg g-1 (15 %) (sum pentaBDE isomers/PUR-H), 0.99 ± 0.27 mg g-1 (27 %) (sum octaBDE isomers/PS), 0.42 ± 0.11 mg g-1 (26 %) (sum octaBDE isomers/ABS). The reproducibility standard deviation sRj and repeatability standard deviation srj were calculated as statistical parameters. The repeatability of the sum of pentaBDE isomers in EP was srj= 0.044 mg g-1 (4.0 %) and the reproducibility was sRj = 0.167 mg g-1 (15 %). srj and the sRj were 0.038 mg g-1 (2.9 %) and 0.195 mg g-1 (15 %), respectively, for the sum of pentaBDE isomers in PUR-H. For the sum of octaBDE isomers in ABS srj and sRj were determined to 0.029 mg g-1 (6.9 %) and 0.114 mg g-1 (27 %), respectively. For the sum of octaBDE isomers in PS the srj = 0.043 mg g-1 (4.3 %) and sRj = 0.255 mg g-1 (26 %) were obtained. KW - Pentabromo Diphenylether (pentaBDE) KW - Octabromo Diphenylether (octaBDE) KW - Polymer KW - Reproducibility KW - Repeatability KW - Directive 2003/11/EC KW - Directive 76/769/EEC KW - GC/MS KW - Polybrominated flame retardants PY - 2005 UR - http://www.umweltbundesamt.de/publikationen/standard-measurement-method-for-determination-of SN - 1862-4804 SN - 0722-186X IS - 31 SP - 1 EP - 151 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-12129 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rockstroh, Jens A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Kalus, Sabine A1 - Jann, Oliver ED - de Oliveira, F. ED - Gameiro da Silva, M. ED - Pinto, R. T1 - Investigations on the Emission of organic Acids from Building Products in Emission Test Chambers - Development of a new Test Method T2 - 8th International Conference "Healthy Buildings" CY - Lisboa, Portugal DA - 2006-06-04 KW - Building products KW - Organic acids KW - VOC KW - GC/MS PY - 2006 VL - 4 SP - 45 EP - 48 PB - Universidade do Porto CY - Lissabon AN - OPUS4-12447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Kasche, J. A1 - Jann, Oliver A1 - Müller, D. T1 - Emissions- und Geruchsuntersuchungen an Bauprodukten - Ergebnisse eines UFO-Planprojektes T2 - 8th Workshop "Odour and Emissions of Plastic Materials" CY - Kassel, Germany DA - 2006-03-27 KW - Bauprodukte KW - Emissionen KW - Geruch KW - RAL UZ PY - 2006 SP - 13-1- 13-7 CY - Kassel AN - OPUS4-12259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, B. A1 - Bitter, F. A1 - Müller, D. A1 - Knudsen, H.N. A1 - Afshari, A. A1 - Wargocki, P. A1 - Olesen, B. A1 - Berglund, B. A1 - Ramalho, O. A1 - Goschnick, J. A1 - Jann, Oliver A1 - Horn, Wolfgang A1 - Nesa, D. A1 - Chanie, E. A1 - Ruponen, M. T1 - Messung der empfundenen Geruchsintensität mit Multigas-Sensorsystemen, das Forschungsvorhaben SysPAQ KW - Geruch KW - Sensorsystem KW - Perceived Air Quality KW - Produkttypischer Geruch KW - Bauprodukte KW - Emissionen PY - 2007 SN - 978-3-18-091995-9 SN - 0083-5560 IS - 1995 SP - 17 EP - 29 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-16370 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kasche, J. A1 - Dahms, A. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Müller, D. T1 - Sensory evaluation of building products - Results of a German round robin test T2 - VDI-Tagung CY - Bad Kissingen, Deutschland DA - 2007-11-13 KW - Bauprodukte KW - Emissionen KW - Geruch KW - AbBB-Schema KW - Kammermessungen KW - Blauer Engel PY - 2007 SN - 978-3-18-091995-9 SN - 0083-5560 IS - 1995 SP - 193 EP - 202 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-16322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brandt, S. A1 - Plehn, W. A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Möglichkeiten und Grenzen der Bewertung und Kennzeichnung geruchsarmer Bauprodukte und Einrichtungen T2 - VDI-Tagung CY - Bad Kissingen, Deutschland DA - 2007-11-13 KW - Bauprodukte KW - Emissionen KW - Geruch KW - AbBB-Schema KW - Kammermessungen KW - Blauer Engel PY - 2007 SN - 978-3-18-091995-9 SN - 0083-5560 IS - 1995 SP - 181 EP - 191 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-16321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emmision aus Materialien in die Luft - Emissionsmesskammern, Luftprobenannahme, Analytik T2 - Kolloquium Hermann-Rietschel-Institut der Technischen Universität CY - Berlin, Germany DA - 2004-12-07 PY - 2004 AN - OPUS4-6539 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Zur Bestimmung des Emissionsverhaltens strahlenhärtender Lacksysteme T2 - Workshop am Fraunhofer-Institut für Holzforschung / Wilhelm-Klausitz-Institut (WKI): Strahlenhärtender Beschichtungssysteme für Holzoberflächen, Techniken - Neuentwicklungen - Restemissionen - Prüfung - Bewertung CY - Braunschweig, Germany DA - 1999-06-17 PY - 1999 AN - OPUS4-7191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Investigations on the emission behaviour of SVOC and POM from indoor materials for the example of wood preservative agents and other low volatile substances T2 - The 8th International Conference on Indoor Air Quality and Climate, Indoor Air '99 CY - Edinburgh, Scotland DA - 1999-08-08 PY - 1999 AN - OPUS4-7192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Bestimmung der Emission schwerflüchtiger organischer Verbindungen aus Materialien am Beispiel von Holzschutzmittelwirkstoffen T2 - Internationales VDI-Kolloquium: Neuere Entwicklungen bei der Messung und Beurteilung der Luftqualität CY - Heidelberg, Germany DA - 1999-04-27 PY - 1999 AN - OPUS4-7189 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionsarme Möbel - Emissionsverhalten, Prüfanforderungen, Umweltzeichen T2 - 5. Fachkongress der Arveitsgemeinschaft Ökologischer Forschungsinstitute (AGÖF), Hochschule Bremen CY - Bremen, Germany DA - 1999-09-23 PY - 1999 AN - OPUS4-7193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Eco-Label for low emission wood products and wood base products (RAL-UZ-38) - Part 1: Criteria and requirements for labelling T2 - Healthy Buildings 2000 CY - Espoo, Finland DA - 2000-08-06 PY - 2000 AN - OPUS4-7196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -