TY - CONF A1 - Wilke, Olaf T1 - Emissions of very volatile organic compounds (VVOC) from particle boards N2 - The latest version of the German AgBB evaluation scheme (2015) for construction products includes some VVOC, e.g. formaldehyde, acetaldehyde and acetone. For these VVOC so-called LCI values (lowest concentration of interest) were derived which are used for the calculation of the so-called R-value (risk index, see reference 1 for the calculation). Test chamber measurements of particle boards show that the emissions of VVOC might have significant impact on the R-value and therefore for the health evaluation. T2 - Indoor Air 2016, The 14th international conference of Indoor Air Quality and Climate CY - Gent, Belgium DA - 03.07.2016 KW - Formaldehyde KW - AgBB evaluation scheme KW - VVOC KW - Particle board KW - OSB KW - Emission test chamber PY - 2016 AN - OPUS4-37033 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Janine A1 - Wilke, Olaf T1 - Standardisierte Formaldehyd- und VOC-Messungen N2 - Der Innenraumluftrichtwert für Formaldehyd in Höhe von 0,1 ppm ist durch das BfR bestätigt worden und bleibt bis auf weiteres bestehen. Die Prüfbedingungen für Formaldehydemissionen aus Holzwerkstoffen dagegen sind nicht mehr aktuell. Das Prüfverfahren für Holzwerkstoffe gilt seit 1991 und basiert auf dem Gebäudestandard von 1984. Eine Definition und Anpassung der Prüfbedingungen an moderne „dichtere“ Bauweise ist notwendig. Es zeigt sich, dass für Verbraucherinnen und Verbraucher eine Unterscheidung von formaldehydbelasteten und -unbelasteten Produkten in der Praxis schwierig ist. Es kann zu fehlerhaftem Einsatz und nicht fachgerechter Verarbeitung der Holzwerkstoffe kommen. Das Ziel des Vorhabens ist die möglichst sichere Einhaltung des Schutzniveaus durch die Anpassung der Prüfbedingungen an den heutigen Gebäudestandard. Aktuelle Versuche und Ergebnisse des Projektes werden vorgestellt. Ergänzende Screening-Versuche (Prüfkammermessungen) weisen Formaldehydemissionen bei verschiedenen Holzwerkstoffen aus dem Handel nach. Für die betrachteten OSB-Platten sind die FA-Emissionen im Allgemeinen geringer als für die untersuchten Spanplatten. Die OSB-Platten zeigen höhere Emissionen für Aceton und Hexanal als die Spanplatten. An ausgewählten Werkstoffen wurden Versuche zu den Auswirkungen einer individuellen Bearbeitung und Messungen unter veränderten Prüfbedingungen durchgeführt. Zum einem wurde schrittweise der Luftwechsel von 1 bis 0,2 1/h reduziert. Zum anderen wurden die Werkstoffe unter sommerlichen Bedingungen vermessen. Die Reduzierung des Luftwechsels ruft einen Anstieg der Formaldehyd-Konzentration hervor, dieser Effekt ist jedoch für einige VOCs stärker ausgeprägt. Bei Luftwechseln von 0,2-0,3 1/h, welche in der Praxis in Gebäuden erreicht werden können, ist eine Überschreitung des Formaldehyd-Grenzwertes von 0,1 ppm vor allem für Spanplatten möglich. Die VOC-Emission steigt unter sommerlichen Bedingungen an, es zeigt sich aber ein schnelles Abklingen nach kurzer Zeit. Die erhöhte Formaldehydemission bleibt über einen längeren Zeitraum erhalten. Die Bearbeitung von unbeschichteten Holzwerkstoffen (in mehrere Teile zersägt) führt zu einem kurzzeitigen Anstieg der FA- und VOC-Emission, nach einer bestimmten Abklingzeit (wenige Tage) wird erneut der Ausgangswert erreicht. Es wurden weiterhin Messungen zu Kombinationen aus OSB- und Spanplatten und einem Holzmöbel durchgeführt. Trotz Erhöhung der Beladung und Beibehalten des Luftwechsels konnte nur ein geringer Anstieg der Formaldehyd- und VOC-Konzentration beobachtet werden. Es erfolgte keine Addition der Einzelkonzentration. T2 - 2. Fachbeirat zum UFOPLAN-Vorhaben Standardisierte Formaldehyd- und VOC-Messungen bei Holzwerkstoffen (FKZ 3714 95 310 0) CY - Berlin, Deutschland DA - 14.06.2016 KW - Formaldehyd KW - Holzwerkstoffe KW - VOC KW - Prüfverfahren PY - 2016 AN - OPUS4-38754 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Analysis of very volatile organic compounds (VVOC) with thermal desorption GC-MS N2 - Most VVOC were rarely considered in the evaluation of construction products. (Salthammer, 2014) In Germany this will change because the latest version of the German AgBB scheme for health evaluation (2015) now include VVOC, e.g. ethyl acetate and ethanol. In this study selected compounds were tested with the procedure described in ISO 16017 and a method for measuring VVOC with thermal desorption was developed. Three different adsorbents Tenax TA, Carbograph 5TD and Carbopack X were tested to analyse VVOC according to ISO 16017. For the tested VVOC, Carbograph 5TD showed the best results under the chosen analytical conditions. T2 - Indoor Air 2016, The 14th international conference of Indoor Air Quality and Climate CY - Gent, Belgium DA - 03.07.2016 KW - Thermal desorption KW - VVOC KW - Carbograph 5TD KW - Carbopack X PY - 2016 AN - OPUS4-37037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Richter, Janine T1 - Standardisierte Formaldehyd- und VOC-Messungen N2 - Der Innenraumluftrichtwert für Formaldehyd in Höhe von 0,1 ppm ist durch das BfR bestätigt worden und bleibt bis auf weiteres bestehen. Die Prüfbedingungen für Formaldehydemissionen aus Holzwerkstoffen dagegen sind nicht mehr aktuell. Das Prüfverfahren für Holzwerkstoffe gilt seit 1991 und basiert auf dem Gebäudestandard von 1984. Eine Definition und Anpassung der Prüfbedingungen an moderne „dichtere“ Bauweise ist notwendig. Es zeigt sich, dass für Verbraucherinnen und Verbraucher eine Unterscheidung von formaldehydbelasteten und -unbelasteten Produkten in der Praxis schwierig ist. Es kann zu fehlerhaftem Einsatz und nicht fachgerechter Verarbeitung der Holzwerkstoffe kommen. Das Ziel des Vorhabens ist die möglichst sichere Einhaltung des Schutzniveaus durch die Anpassung der Prüfbedingungen an den heutigen Gebäudestandard. Es werden das Projekt (UFOPLAN-Vorhaben FKZ 3714 95 310 0) und erste Messergebnisse vorgestellt. Erste Messungen von Holzwerkstoffen im laufenden Vorhaben unter „worst case“-Bedingungen (erhöhte Beladung, geringer Luftwechsel) zeigen hohe Formaldehyd-Emissionen. T2 - 1. Fachbeirat zum UFOPLAN-Vorhaben Standardisierte Formaldehyd- und VOC-Messungen bei Holzwerkstoffen (FKZ 3714 95 310 0) CY - Berlin, Germany DA - 15.01.2016 KW - Formaldehyd KW - Holzwerkstoffe KW - Prüfverfahren PY - 2016 AN - OPUS4-38753 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Reproducibly emitting reference material for quality assurance/quality control of emission test chamber measurements N2 - Volatile Organic Compounds (VOC) are ubiquitous in the indoor air, since they emit from materials used indoors. Investigations of these materials are mostly carried out in test chambers under controlled climatic conditions. Quality control of these test chamber measurements is important but there is a lack of commercially available homogenous reference materials as required for round robin tests or quality assurance of laboratories. The approach of the present study is the impregnation of a supporting material with VOC, which are reproducibly released in measurable chamber air concentrations under standardised test conditions. A polymer made of Thermoplastic Polyurethane (TPU) was chosen as carrier material. It was impregnated with the VOC trimethyl pentanediol isobutyrat (texanol). T2 - Healthy Buildings 2017 Europe CY - Lublin, Poland DA - 02.07.2017 KW - Emissions testing KW - Volatile organic compounds KW - Polymeric material KW - CO2 assisted impregnation PY - 2017 AN - OPUS4-42351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Janine A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Emissions of formaldehyde and VOC from wood-based building products N2 - Wood-based materials are well-known sources for formaldehyde emission in the indoor environment. Different testing standards lead to different emission values for the materials. Such standards are compared in this study. Besides scenarios with varying loading factors, air exchange rates and climatic conditions were investigated to evaluate the formaldehyde emission potential of different building products. Under realistic indoor conditions used for the emission chamber tests, exceeding of formaldehyde indoor guide values were obtained. Results showed the need for improvement of wood-based materials with lower formaldehyde emissions and the adaption of testing parameters closer to realistic conditions. T2 - Healthy Buildings 2017 Europe CY - Lublin, Poland DA - 02.07.2017 KW - Formaldehyde KW - Emission chamber testing KW - Particle board KW - OSB PY - 2017 SN - 978-83-7947-232-1 SP - Paper 0175, 1-6 AN - OPUS4-41575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Emissions of formaldehyde from acoustic tiles N2 - Acoustics is an important aspect for large rooms especially in schools, kindergartens and offices. Foam tiles made from melamine resins are often used for acoustic insulation because they show good fire resistance and good thermal insulation properties. But they can emit formaldehyde. In Germany there are cases with a resulting indoor air concentration of higher than 100 µg/m³. In this study samples from two schools and one office were investigated. Additionally, new tiles were purchased and tested to evaluate the general potential as formaldehyde source. T2 - Healthy Buildings 2017 Europe CY - Lublin, Poland DA - 02.07.2017 KW - Building products KW - Emission test chamber KW - Formaldehyde KW - Foam tiles PY - 2017 AN - OPUS4-41573 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Comparison of Formaldehyde Concentrations in Emission Test Chambers Using EN 717-1 and EN 16516 N2 - For more than 25 years EN 717-1 (Wood-based panels - Determination of formaldehyde re-lease - Part 1: Formaldehyde emission by the chamber method) is the standard for formalde-hyde emission testing of wooden boards. In 2017 EN 16516 (Construction products - Assess-ment of release of dangerous substances - Determination of emissions into indoor air) was published as a new harmonised standard for the emission testing of construction products. Because test chamber conditions are different, both standards give different concentrations for formaldehyde. To determine a conversion factor four test series were set up with different wooden boards. For a loading of 1 m²/m³ the conversion factor is 1.6. This means that the formaldehyde concentration measured under the conditions of EN 16516 is a factor of 1.6 higher compared to EN 717-1. T2 - Conference on Indoor Air CY - Philadelphia, PA, USA DA - 22.07.2018 KW - Loading factor KW - European standard KW - Construction products KW - Air exchange rate PY - 2018 SP - paper 627 AN - OPUS4-45630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Standardisierte Formaldehyd- (und VOC-) Messungen bei Holzwerkstoffen zur Einspeisung der Daten in Normungsprozesse N2 - UBA und BAM schlagen die Durchführung der Prüfkammermessungen bei 23 °C und 50% relativer Luftfeuchte, einer Beladung von 1,8 m²/m³ und einem Luftwechsel von 0,5 pro Stunde vor. Diese Parameter orientieren sich an der EN 16516, die als zukünftige „Referenznorm“ zu betrachten ist. Die Schmalflächenversiegelung ist auch zukünftig wie in der EN 717-1 beschrieben vorzunehmen. Nach 28 Tagen wird der Mittelwert einer Doppelbestimmung als Endkonzentration („entsprechend der Ausgleichskonzentration“) berechnet. Alternativ dazu kann die Prüfung vorzeitig abgebrochen werden, wenn an 5 Messtagen der Prüfung eine Formaldehydkonzentration von 0,1 ppm nicht überschritten wird. Prüfungen nach der EN 717-1 sollen weiterhin gleichberechtigt möglich sein. Ergebnisse von Messungen, die nach der EN 717-1 ermittelt wurden, sind mit dem Faktor 2,0 zu multiplizieren. Abgeleitete Verfahren wie z.B. das Gasanalyseverfahren sollen weiterhin möglich sein. Das Perforatorverfahren entfällt hier, da eine allgemeine für alle Holzwerkstoffe gültige Korrelationen nicht existiert. Die entsprechenden Änderungen sind in der vom BMUB veröffentlichten „Bekanntmachung analytischer Verfahren für Probenahmen und Untersuchungen für die im Anhang der Chemikalien-Verbotsverordnung genannten Stoffe und Stoffgruppen“ entsprechend zu ändern. T2 - UFOPLAN Workshop CY - Berlin, Germany DA - 22.06.2018 KW - EN 717-1 KW - Prüfkammer KW - Formaldehyd KW - EN 16516 PY - 2018 AN - OPUS4-45632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Richter, Matthias A1 - Jann, Oliver T1 - Volatile organic compounds from building products - Results from six round robin tests with emission test chambers conducted between 2008 and 2018 N2 - Emission testing of volatile organic compounds (VOC) from materials and products is commonly based on emission test chamber measurements. To ensure the comparability of results from different testing laboratories, their measurement performance must be verified. For this purpose, Bundesanstalt für Materialforschung und -prüfung (BAM) organizes an international proficiency test (round robin test, RRT) every two years using well-characterized test materials (one sealant, one furniture board, and four times a lacquer) with defined VOC emissions. The materials fulfilled the requirements of homogeneity, reproducibility, and stability. Altogether, 36 VOCs were included of which 33 gave test chamber air concentrations between 13 and 83 µg/m3. This is the typical concentration range to be expected and to be quantified when performing chamber tests. Three compounds had higher concentrations between 326 and 1105 µg/m3. In this paper, the relative standard deviations (RSD) of BAM round robin tests since 2008 are compared and the improvement of the comparability of the emission chamber testing is shown by the decrease of the mean RSD down to 28 % in 2018. In contrast, the first large European interlaboratory comparison in 1999 showed a mean RSD of 51 %. KW - Construction product KW - Emission test chamber KW - Interlaboratory comparison KW - Proficiency testing KW - Rround robin test KW - VOC emission PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526139 DO - https://doi.org/10.1111/ina.12848 VL - 31 IS - 6 SP - 2049 EP - 2057 PB - Wiley AN - OPUS4-52613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Erfassung der Zahl feiner und ultrafeiner Partikel aus Bürogeräten während der Druckphase zur Entwicklung eines Prüfverfahrens für das Umweltzeichen Blauer Engel für Bürogeräte mit Druckfunktion - Zusammenfassung N2 - Vor dem Hintergrund der anhaltenden öffentlichen Diskussion um mögliche gesundheitliche Risiken von Ultrafein- und Feinstaubemissionen aus Bürogeräten mit Laserdruckfunktion (LPD, Laser Printing Device) wurde vom Umweltbundesamt ein Forschungsvorhaben zur Entwicklung einer Prüfprozedur für die Quantifizierung der emittierten Partikel durch Zählung unter Standardbedingungen in Emissionsmesskammern, sowie zur physikalischen und chemischen Charakterisierung dieser Aerosole initiiert. Als Ergebnis konnte die Partikelzählung in den Entwurf des Prüfverfahrens für die Bestimmung von Emissionen (RAL-UZ-122, Anhang S-M) des Umweltzeichens "Blauer Engel" für Bürogeräte sowie in den Prüfstandards ECMA-328 und den Entwurf der ISO/IEC 28360 integriert werden. Die Methode wurde in einem internationalen Ringversuch erfolgreich getestet. Auf dieser Basis können Vergabekriterien und -werte für die Emission von Fein- und Ultrafeinpartikeln im Rahmen der Vergabe des Umweltzeichens Blauer Engel vereinbart und Produktprüfungen vorgenommen werden. KW - Blauer Engel KW - Bürogeräte mit Druckfunktion KW - Partikelemission KW - RAL-UZ 122 PY - 2011 VL - Förderkennzeichen UFOPLAN 3708 95 301 SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59863 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poelke, B. A1 - Klein, Luise A1 - Hoffmann, H. A1 - Wilke, Olaf A1 - Roloff, A. T1 - Bestimmung von VOC-Emissionen aus Verbraucherprodukten in mikroskaligen Emissionsprüfkammern: Ergebnisse eines Rundversuchs T1 - Determining VOC Emissions from Consumer Products in Micro-Scale Emission Test Chambers: Results of a Round Robin Test N2 - Die Bestimmung der Anfangskonzentrationen flüchtiger organischer Verbindungen, die innerhalb der ersten Stunden des Gebrauchs aus Verbraucherprodukten emittiert werden, wurde in einem Ringversuch getestet, bei dem Mikro-Kammern verwendet wurden. Neun Labore nahmen an dem Ringversuch teil, der sich aus zwei Teilen zusammensetzte: Im ersten Teil wurde die analytische Leistungsfähigkeit beurteilt. Jedes beteiligte Labor erhielt zwei mit Analyten dotierte Tenax® TA Desorptionsröhrchen zur Qualitätskontrolle (QC). Im zweiten Teil führte jedes Labor Emissionsmessungen über einen Zeitraum von 48 Stunden in Mikro-Kammern mit Volumina von 44 oder 114 ml durch. Als Probenmaterial dienten Stücke eines Regenponchos, der Cyclohexanon, Phenol, 2-Ethylhexanol, Naphthalin und Isophoron in signifikanten Konzentrationen emittierte. Für den QC-Test wurden sehr geringe relative Standardabweichungen (9 14 %) erhalten. Die Ergebnisse der Emissionsmessungen waren ebenfalls sehr gut. In der frühen Phase (0,5 4 Stunden) wurden akzeptable z-Scores (|z| ≤ 2,00) von mindestens sieben Laboren erhalten, nach 24 und 48 Stunden erhielten alle Labore akzeptable z-Scores. KW - Emissionsprüfkammer KW - Ringversuch KW - Verbraucherprodukt KW - VOC-Emission PY - 2025 DO - https://doi.org/10.37544/0949-8036-2025-03-04-71 VL - 85 IS - 03-04 SP - 71 EP - 76 AN - OPUS4-63561 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Beck, Oliver A1 - Wilke, Olaf A1 - Pyza, Lars A1 - Seeger, Stefan T1 - Test procedure for the evaluation of adsorptive building materials N2 - Construction materials working on the basis of physisorption or chemisorptions are considered as an additional means to improve indoor air quality. Some manufacturers promise a complete demineralisation of VOCs into C02 and water being not possible for most of typical indoor air pollutants. On the contrary, sometimes new substances are generated due to surface reactions, e.g. formaldehyde (Salthammer and Fuhrmann, 2007). For evaluating such products a testing system was built up at BAM enabling testing under defined, reproducible and realistic conditions. Tue VOC test gas is provided by a gas mixing system (GMS) developed at our institute (Richter, 2010). VOC gas mixtures with retraceable concentrations between 1 µg m·3 up to 1.5 mg m·3 can be produced. A gypsum board promoted as an 'air cleaner' was put in a 1 m3 emission test chamber connected with the GMS. The board was exposed to a gas mixture of four VOCs - ethyl acetate, hexanal, (+)-a-pinene and R-(+)-limonene - with gas concentrations between 600 µg m·3 and 1,440 µg m·3 for a period of 14 days. T2 - Healthy Buildings 2012 - 10th International conference CY - Brisbane, Australia DA - 08.07.2012 KW - Air cleaning KW - Sorptive construction materials KW - Test procedure KW - Volatile organic compound KW - Test gas generation KW - Healthy homes and buildings KW - Material and construction KW - Product safety KW - Risk assessment PY - 2012 SN - 978-1-921897-40-5 SP - 43 EP - 44 (Session 4B) AN - OPUS4-27558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mull, Birte A1 - Möhlmann, L. A1 - Wilke, Olaf T1 - Photocatalytic degradation of toluene, butyl acetate and limonene under UV and visible light with titanium dioxide-graphene oxide as photocatalyst N2 - Photocatalysis is a promising technique to reduce volatile organic compounds indoors. Titanium dioxide (TiO2) is a frequently-used UV active photocatalyst. Because of the lack of UV light indoors, TiO2 has to be modified to get its working range shifted into the visible light spectrum. In this study, the photocatalytic degradation of toluene, butyl acetate and limonene was investigated under UV LED light and blue LED light in emission test chambers with catalysts either made of pure TiO2 or TiO2 modified with graphene oxide (GO). TiO2 coated with different GO amounts (0.75%–14%) were investigated to find an optimum ratio for the photocatalytic degradation of VOC in real indoor air concentrations. Most experiments were performed at a relative humidity of 0% in 20 L emission test chambers. Experiments at 40% relative humidity were done in a 1 m³ emission test chamber to determine potential byproducts. Degradation under UV LED light could be achieved for all three compounds with almost all tested catalyst samples up to more than 95%. Limonene had the highest degradation of the three selected volatile organic compounds under blue LED light with all investigated catalyst samples. KW - Photocatalysis KW - Emission test chamber KW - Volatile organic compound KW - VOC KW - Degradation PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-402955 DO - https://doi.org/10.3390/environments4010009 SN - 2076-3298 VL - 4 IS - 1 SP - Article 9, 1 EP - 9 PB - MDPI CY - Basel AN - OPUS4-40295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pech, Anja A1 - Wilke, Olaf A1 - Mull, Birte A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Development of a TDS-GC-FID method for the determination of methanol and ethanol in air N2 - A method for the determination of very volatile organic compounds (VVOC) in air was developed and successfully tested for methanol and ethanol. Carbotrap300® (a multi-bed tube using Carbopack C®, Carbopack B® and Carbosive SIII®) was selected as sorption material for thermal desorption and tested for its suitability for emission test chamber measurements. The adsorption behaviour and the chromatographic results are influenced negatively by spiking aqueous solutions on the adsorption medium for calibration purposes. The latter effect can be reduced by blowing dry air across the adsorbent to remove the adsorbed water. Detection and quantification limits were determined for a GC-FID system and compared to GC-MS. The applicability of the method was tested with a methanol eliminating silane modified polymeric adhesive (SMP-adhesive for parquet) in an emission test chamber N2 - Eine Methode zur Bestimmung von sehr leicht flüchtigen Verbindungen in Luft wurde für Methanol und Ethanol entwickelt und erfolgreich getestet. Dafür wurde Carbotrap300® (Multibettrohr aus Carbopack C®, Carbopack B® und Carbosive SIII®) als Sorptionsmedium für die Thermodesorption ausgewählt und dessen Eignung für Emissionskammermessungen untersucht. Das Adsorptionsverhalten und die chromatographischen Ergebnisse werden negativ durch die Aufgabe von wässrigen Kalibrierlösungen auf das Adsorptionsmedium beeinflusst. Durch das Überleiten von trockener Luft kann dieser Effekt verringert werden, da so das adsorbierte Wasser entfernt wird. Die Nachweis- und Bestimmungsgrenzen wurden für ein eingesetztes GC- FID-System ermittelt und mit einem GC-MS verglichen. Mit einem methanolabspaltenden silanmodifizierten Polymerklebstoff (SMP-Parkettkleber), der in eine Emissionskammer eingebracht wurde, konnte die Tauglichkeit der Methode überprüft werden. PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-297020 UR - http://www.gefahrstoffe.de/gest/article.php?data[article_id]=76019 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 73 IS - 11/12 SP - 477 EP - 482 PB - Springer-VDI-Verlag CY - Düsseldorf AN - OPUS4-29702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Horn, Wolfgang A1 - Richter, Matthias A1 - Nohr, M. A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Application of a novel reference material in an international round robin test on material emissions testing N2 - Emission testing of products is currently a rapidly increasing field of measurement activity. Labelling procedures for construction products are based on such emission test chamber measurements and hence measurement performance should be verified. A suited procedure for this purpose is the testing of one unique homogenous material in different laboratories within a Round Robin Test (RRT). Therefore, it is useful to have a reference material which can be used within inter-laboratory studies or as part of the quality management system to ensure comparable results. Several approaches on the development of reproducibly emitting materials have been published. These have in common only to emit a single VOC – toluene. Two further research studies carried out by BAM aimed to develop reference material for emissions testing containing one or more VOC in a single material. The first approach was a doped lacquer with Volatile and Semi-Volatile Organic Compounds (VOC/SVOC) and the second was Thermoplastic Polyurethane (TPU) or a Squalane/Paraffin mixture. Results received with the lacquer based material were presented in more detail. KW - Emission test chamber KW - Reference material KW - Round robin test KW - VOC PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-419412 DO - https://doi.org/10.1111/ina.12421 SN - 1600-0668 SN - 0905-6947 VL - 28 IS - 1 SP - 181 EP - 187 PB - Wiley & Sons, Ltd. AN - OPUS4-41941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Emission Testing for Indoor Products N2 - The chemical emissions from products are tested by means of emission test chambers under defined conditions (climate, loading, air change rate). The standard method for the determination of volatile organic compounds (VOC) is the sampling onto Tenax-tubes followed by thermal desorption (TDS) and gas chromatography-mass spectrometry (GC-MS) analysis. The EU-LCI list includes some very volatile organic compounds (VVOC) and some VOC for which there are limitations when using the standard method. For VVOC additional sampling is required using stronger absorbers like Carbotrap or multi-bed adsorption tubes. The analysis of VVOC also requires a different GC oven program and a different column for the separation. For the determination of formaldehyde and other low boiling aldehydes (e.g. acetaldehyde, acetone, propanal, propenal) DNPH-cartridges are used which are extracted with acetonitrile followed by liquid chromatography (HPLC-UV) analysis. The derivatisation of propenal and other unsaturated aldehydes (e.g. 2-butenal) with DNPH might lead to lower findings due to incomplete derivatization and forming of by-products. For a better quantification of acetic acid the use of ion chromatography (IC) is recommended because the analysis of acetic acid with the standard method (TDS) leads to lower findings due to break through during sampling. The use of ion chromatography for the analysis of organic acids requires a third sampling technique. The acids are adsorbed onto silica-gel and extracted with water. T2 - ISESISIAQ 2019 CY - Kaunas, Lituania DA - 18.08.2019 KW - Indoor Air Quality KW - Emission Testing KW - Indoor Products KW - VOC Emission KW - Construction Products PY - 2019 AN - OPUS4-49406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Olaf A1 - Jann, Oliver A1 - Plehn, W. A1 - Brozowski, F. T1 - Untersuchungen zur Etablierung der DIN EN 16516 als neuer Referenznorm für die Prüfung von Formaldehydemissionen aus Holzwerkstoffen gemäß Chemikalien-Verbotsverordnung T1 - Investigations to establish DIN EN 16516 as new reference standard for testing of formaldehyde emissions from wood-based panels under the Chemikalien-Verbotsverordnung N2 - Im Januar 2018 wurde die DIN EN 16516 „Bauprodukte: Bewertung der Freisetzung gefährlicher Stoffe – Bestimmung von Emissionen in die Innenraumluft“ als harmonisierte europäische Prüfnorm veröffentlicht. Für die Etablierung der DIN EN 16516 als neue Referenznorm wurden verschiedene Emissionsprüfungen mit dem Ziel durchgeführt, ein neues Prüfverfahren für Formaldehydemissionen aus Holzwerkstoffen zu erarbeiten. Das übergeordnete Ziel ist die Minimierung des Risikos von Überschreitungen des Innenraumrichtwertes für Formaldehyd. Die Untersuchungen ergaben teilweise hohe Formaldehydemissionen, insbesondere bei höheren Beladungsfaktoren und Temperaturen, sowie bei niedrigen Luftwechselraten. Eine getestete Spanplatte hätte aufgrund ihrer hohen Formaldehydemission nicht auf den deutschen Markt gebracht werden dürfen. Durch vergleichende Untersuchungen konnte ein Umrechnungsfaktor in Höhe von 2,0 für die Umrechnung von Prüfwerten nach DIN EN 717-1 zu DIN EN 16516 abgeleitet werden. N2 - DIN EN 16516 "Construction products: Assessment of release of dangerous substances - Determination of emissions into indoor air" was published as a harmonized European standard in January 2018. For the establishment of DIN EN 16516 as the new reference standard various emission tests were carried out with the aim to develop a new test procedure for the measurement of formaldehyde emissions from wood-based panels. The superior aim is to minimize the risk of exceeding the indoor air reference value for formaldehyde. The investigations showed some particularly high formaldehyde emissions, especially at higher loading and temperature and at low air change rates. One of the tested particle boards exceeded the formaldehyde limit value and should not have been sold in Germany. For the conversion of test values from DIN EN 717-1 to DIN EN 16516 a conversion factor of 2.0 was derived from the comparative investigations. KW - Formaldehyd KW - DIN EN 16516 KW - Innenraumluft KW - Emissionsprüfung PY - 2019 SN - 0949-8036 VL - 79 IS - 3 SP - 79 EP - 85 PB - VDI Fachmedien CY - Düsseldorf AN - OPUS4-47666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Formaldehydmessungen an Holzwerkstoffplatten N2 - Die von der BAM eingekauften Holzwerkstoffplatten (Verlegespanplatten, OSB, Multiplexplatten) verschiedener Hersteller zeigten teilweise hohe Formaldehyd-emissionen unter den Prüfbedingungen nach EN 16516, eine Spanplatte hielt den Grenzwert von 0,1 ppm selbst bei Prüfung nach DIN EN 717-1 nicht ein, dürfte also in Deutschland gar nicht in den Verkauf gelangen. Holzwerkstoffe, die unter den Prüfbedingungen der DIN EN 717-1 die Formaldehydklasse E1 einhalten, können insbesondere bei großflächigem Einsatz im Innenraum zu Überschreitungen des Richtwertes für die Innenraumluft führen. Zusätzlich zur Anpassung des Luftwechsels ist auch der Parameter Beladung bei einer Überarbeitung der Norm anzupassen. In der DIN EN 16516 werden produktspezifische (am Einsatz der Produkte orientierte) Beladungsfaktoren vorgegeben. Für den Einsatz von Holzwerkstoffplatten ergäben sich Beladungen von 0,4 (Boden oder Decke), 1,0 (Wände), 1,4 (Wände plus Boden oder Decke) und 1,8 m²/m³ (Wände, Boden und Decke). Um die realen Bedingungen in modernen Gebäuden abzubilden, ist deshalb eine Beladung von 1,8 m²/m³ für die Prüfkammermessung erforderlich. Hierbei ist darauf hinzuweisen, dass für die Beladung im Referenzraum Möbel nicht berücksichtigt wurden. Damit soll sichergestellt werden, dass die Einhaltung des Schutzniveaus bei realen Innenraumbedingungen auch unter den Randbedingungen eines niedrigen Luftwechsels sowie bei sommerlichen Bedingungen und heutigem Lüftungsverhalten der Menschen soweit wie möglich gewährleistet ist. T2 - 26. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 20.05.2019 KW - Formaldehyd KW - Emissionsprüfkammer KW - DIN EN 16516 KW - DIN EN 717-1 PY - 2019 AN - OPUS4-48065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -