TY - JOUR A1 - Steiner, S. A1 - Heldt, J. A1 - Sobol, Oded A1 - Unger, Wolfgang A1 - Frömeling, T. T1 - Influence of oxygen vacancies on core-shell formation in solid solutions of (Na,Bi)TiO3 and SrTiO3 N2 - Solid solutions of (Na,Bi)TiO3 (NBT) and SrTiO3 (ST) are materials of interest for high-strain or high-energy density capacitor applications. Often, they exhibit chemical heterogeneity and develop core-shell structures during regular solid-state synthesis with an NBT-rich core. In this case, the NBT forms first so that the strontium needs to diffuse into the material to reach chemical homogeneity. Depending on the presence of core-shell structures, the electrical properties can vary drastically. In this work, we rationalize the effect of variations in oxygen vacancy concentration by Fe-acceptor and Nb-donor doping. It can be shown that a diffusion couple of strontium and oxygen is responsible for chemical homogenization and that the oxygen vacancy content can control the formation of a core-shell structure. KW - Lead-free ceramics KW - Bismuth titanates KW - Core-shell structures KW - Diffusion/diffusivity KW - Ferroelectricity/ferroelectric materials PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-525988 DO - https://doi.org/10.1111/jace.17845 SP - 1 EP - 10 PB - Wiley Periodicals LLC, John Wiley & Sons, Inc. AN - OPUS4-52598 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - The characterization of oxygen diffusion in (Na1/2Bi1/2)TiO3 piezo-ceramics by Time-of-Flight secondary ion mass spectrometry (ToF-SIMS) N2 - The ferroelectric ceramic NBT and its solid solutions with barium titanate (BT) are examples for the most promising lead free materials to substitute the dominant Pb(Zr,Ti)O3 (PZT). Lead based material should generally be disregarded due to environmental and health reasons. However, there is no class of lead-free piezoelectric materials that can replace PZT entirely. Not only the often inferior ferroelectric properties but also the lack of understanding of the defect chemistry of NBT is still a challenge for the replacement of lead containing piezo-ceramics. Just recently it could be shown by Li et al. that NBT obtains extraordinarily high oxygen ionic conductivity when doped with Mg as acceptor. It was actually expected that doping just leads to a hardening of the ferroelectric properties. However, it became clear that the known defect chemical behavior of PZT cannot be extrapolated to NBT materials. Hence, to gain information on general doping effects a better defect chemical investigation is needed. This is particularly important for the applications with high reliability demands to investigate possible degradation and fatigue mechanisms. In the present work Time-of-flight-secondary ion mass spectrometry (ToF-SIMS) was used in order to observe the influence of different acceptor dopants (Fe, Ni, Al) on the oxygen diffusion in NBT. ToF-SIMS holds the ability to gain a full elemental distribution in a sub-micron resolution and was therefore chosen to provide the essential information on the favorable diffusion paths of oxygen in NBT in dependence of the chosen doping element. 18O was used as a tracer for oxygen as its natural abundance is only 0.2%. The doped NBT samples have been annealed for 5 h at 500°C in a 0.2 bar 18O-tracer atmosphere to be able to detect oxygen ion diffusion. ToF-SIMS investigations were conducted on a ToF-SIMS IV (ION TOF GmbH, Münster, Germany) using a Bi+ primary ion beam (25KeV in collimated burst alignment mode with a beam diameter of ~150 nm) and a Cs+ sputter beam (3KeV). The results illustrate the different impact of dopants on the diffusion properties which is evidence for a highly non-linear dependence on dopant type and concentration. T2 - 21st International Conference on Secondary Ion Mass Spectrometry - SIMS21 CY - Krakow, Poland DA - 10.09.2017 KW - ToF-SIMS KW - NBT KW - Piezoceramics PY - 2017 UR - http://sims.confer.uj.edu.pl/boa_poster.php?id=93 AN - OPUS4-42911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grimault de Freitas, Tomás A1 - de Araujo Abilio, André A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Krzysch, Zephanja A1 - Böllinghaus, Thomas A1 - Sobol, Oded T1 - Challenges with metallic materials for the transport and storage of hydrogen N2 - The hydrogen economy is one of the most important solutions to achieve climate neutrality in Europe. It involves the production, storage, transport and use of large quantities of hydrogen in existing and new infrastructures. Components along this supply chain, such as pipelines and storage tanks, are made of various metallic materials, with steel being the most common construction material. The rapid introduction of hydrogen therefore brings with it major challenges, in particular the need for comprehensive qualification of components and materials to ensure the sustainable and safe use of hydrogen technologies. This article provides an overview of the state of the art in the testing of materials and components as well as corresponding future trends and developments for a successful transition to a hydrogen economy. T2 - VGBE - Materials and Quality Assurance 2023 CY - Bergheim, Germany DA - 10.05.2023 KW - Hydrogen Embrittlement KW - Materials Testing KW - Component Testing KW - High-Pressure Gaseous Hydrogen KW - Hollow Specimen Technique PY - 2024 VL - 4 SP - 60 EP - 64 PB - VGBE Energy AN - OPUS4-60686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - Hydrogen assisted cracking phenomena in duplex stainless steels elucidated by in- and ex-situ ToF-SIMS experiments N2 - In the presented research, the high potential and abilities of secondary ion mass spectrometry (ToF-SIMS) to detect and locally map the hydrogen distribution in two types of duplex stainless steels are shown. The research validates certain proposed mechanisms by combining ToF-SIMS with high-resolution scanning electron microscopy and electron-backscattered diffraction. The combination of data from several techniques on the same region was conducted in this field for the first time by applying data treatment of the ToF-SIMS raw data and data fusion approach. This powerful combination of methods allows reviewing of the occurring processes related to hydrogen assisted cracking. The step beyond the state of the art in this field was gained here by developing permeation and mechanical loading experiments within the ToF-SIMS during chemometric imaging of the hydrogen distribution in the microstructure. The research presents the necessary correlation between the hydrogen distribution and the resulted structural changes, the diffusion behavior in a duplex microstructure and stress induced diffusion of hydrogen by applying external load at the microscale. T2 - 6th WMRIF Early Career Scientist Summit CY - NPL Teddington UK DA - 18.06.2018 KW - ToF-SIMS KW - Duplex stainless steel KW - LDX KW - EBSD KW - Data-fusion PY - 2018 AN - OPUS4-46865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - Sputtering derived artefacts in austenitic steel during Time-of-Flight Secondary Ion Mass Spectrometry analyses N2 - Among the very few techniques to localize hydrogen (H) at the microscale in steels, Time-of-flight secondary ion mass spectrometry (ToF-SIMS) was proven to be a reliable tool. The necessity to detect hydrogen stems from its deleterious effects in metals, that are often used as structural components and to obtain better understanding of the underlying metallurgical mechanisms of hydrogen embrittlement (HE) which are still unclear. Austenitic stainless steels are nowadays commonly used in a wide variety of application, from hydrogen transport and storage facilities to petrochemical and offshore applications where they are exposed to aggressive environments and therefore prone to HE. One of the greater risks in the austenitic class is the embrittlement of the material due to the instability of the γ austenite and its transformation into a brittle α martensitic phase. This transformation takes place due to the local stresses that are induced by the uptake of hydrogen during service. Nonetheless, it was shown that this transformation can occur as an artefact during SIMS analysis itself where Cs-sputtering is necessary not only to remove surface contaminations but mainly to enhance H/D secondary ion yield. In the following contribution we show the influence of different sputtering conditions on AISI 304L austenitic stainless steel in order to distinguish the artefact from the hydrogen induced transformation. The material was charged electrochemically in a deuterium based electrolyte. Deuterium (D) must be in these experiments as a replacement for hydrogen which cannot be used because adsorbed hydrogen superimposes hydrogen originating from charging the sample in the SIMS images. ToF-SIMS analyses were conducted by ToF SIMS IV (IONTOF GmbH, Münster, Germany). The experiments were carried out on deuterium charged and non-charged samples. The structural characterization was carried out by SEM and EBSD examinations before and after charging, both with a Leo Gemeni 1530VP field-emission scanning electron microscope and a Zeiss Supra 40 instrument (Carl Zeiss Microscopy GmbH, Oberkochen, Germany). The results showed that the use of 1keV Cs+ beam induces stacking faults while higher sputter beam energies results in γ→α transformation. T2 - SIMS Europe 2018 CY - Münster, Germany DA - 16.09.2018 KW - Austenitic steel KW - Hydrogen KW - ToF-SIMS KW - Artefact PY - 2018 AN - OPUS4-46701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - Challenges with metallic materials in hydrogen technologies N2 - The contribution was presented in the Joint European Summer School in Athens as part of several contributions from BAM in the field of hydrogen safety. These presentations are given in order to provide an overview about the activities of BAM as part of the competence center H2Safety@BAM T2 - JOINT EUROPEAN SUMMER SCHOOL (JESS) CY - Athens, Greece DA - 12.09.2022 KW - Gaseous hydrogen KW - Hydrogen Embrittlement KW - Hydrogen assisted cracking PY - 2022 AN - OPUS4-55822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wurzler, Nina A1 - Sobol, Oded A1 - Altmann, Korinna A1 - Radnik, Jörg A1 - Özcan Sandikcioglu, Özlem T1 - Preconditioning of AISI 304 stainless steel surfaces in the presence of flavins—Part I: Effect on surface chemistry and corrosion behavior N2 - Stainless steel AISI 304 surfaces were studied after a mild anodic polarization for oxide growth in the presence and absence of two derivatives of vitamin B2 (riboflavin and flavin mononucleotide) that can be secreted by metal‐reducing bacteria and act as a chelating agent for iron species. The alterations in oxide chemistry were studied by means of surface‐sensitive techniques such as X‐ray photoelectron spectroscopy and time‐of‐flight secondary ion mass spectrometry analysis. The complementary electrochemical characterization revealed a preferential growth of an oxide/hydroxide iron‐rich film that is responsible for an altered pit initiation and nucleation behavior. These findings suggest that as the corrosion behavior is determined by the interplay of the chemical and electronic properties, only a mild anodic polarization in the presence of redox‐active molecules is able to alter the chemical and electronic structure of the passive film formed on stainless steel AISI 304. This helps to achieve a profound understanding of the mechanisms of microbially influenced corrosion (MIC) and especially the possible effects of the redox‐active biomolecules, as they may play an important role in the corrosion susceptibility of stainless steel surfaces. KW - Corrosion KW - Stainless steel KW - Surface analysis PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-528117 DO - https://doi.org/10.1002/maco.202012191 VL - 72 IS - 6 SP - 974 EP - 982 PB - Wiley AN - OPUS4-52811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ekici, Nilsah A1 - Sobol, Oded T1 - SHIMMER Database for Hydrogen Integration in European Gas Grids N2 - The integration of hydrogen into existing natural gas infrastructure is an important pathway for achieving the European Union’s climate neutrality goals. However, hydrogen blending in gas networks raises technical challenges related to material compatibility, operational safety, and the lack of harmonized assessment methodologies across Europe. These challenges are addressed within the Safe Hydrogen Injection Modelling and Management for European Gas Network Resilience (SHIMMER) project, funded by the Clean Hydrogen Partnership under the Horizon Europe programme. A key outcome of the project is the development of an openly accessible database designed to support the assessment of hydrogen readiness in European gas networks and to facilitate knowledge sharing. The database compiles infrastructure data provided by project partners, including several European transmission and distribution system operators. It contains detailed information on gas network components such as pipelines, valves, fittings, gaskets, and compressors. In addition, a new category has been introduced focusing on the hydrogen compatibility of gas grid components and materials. This section provides structured information linking infrastructure components with material types and their hydrogen compatibility, enabling more systematic evaluation of hydrogen injection scenarios. By organizing heterogeneous datasets into a harmonized and user-friendly structure, the SHIMMER database supports research, best-practice development, and the safe integration of hydrogen into existing European gas infrastructure. T2 - EHEC 2026 CY - Seville, Spain DA - 11.03.2026 KW - Database KW - Gas Grid KW - Hydrogen KW - Low-carbon KW - Pipeline Steel PY - 2026 AN - OPUS4-65683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -