TY - JOUR A1 - Mazzei, S. A1 - Madia, Mauro A1 - Beretta, S. A1 - Mancaleoni, A. A1 - Aparo, S. T1 - Analysis of Cu-wire pull and shear test failure modes under ageing cycles and finite element modelling of Si-crack propagation N2 - In microelectronic packaging, wire bonding is the predominant method for making electrical connections. Copper is increasingly substituting gold as interconnection material since it is a much cheaper alternative and it also offers several physical advantages. Adequate and reliable mechanical integrity of the connection is usually checked by process controls based onto 'wire pull' and 'ball bond shear' tests. In this paper the two methods are compared in terms of sensitiveness in detecting a latent weakness of the bond-pad structure, either induced by inappropriate wire bonding process or cumulated during reliability ageing. The failure modes (in terms of frequency and maximum test load) observed at the ball bond interface have been investigated on two different batches of a same chip, obtained from different wire-bonding recipes and including both unstressed and aged units. Cross-sections of the samples, submitted to pull and shear both in destructive and non-destructive tests, have allowed us to investigate the relationship between the bond morphological characteristics (metal deformation and potential micro-damages induced by copper bonding) and the weak points for fracture propagation inside the bond-pad inner layers and the silicon substrate. Besides the experimental activities, fracture mechanics and the finite element method have been employed to model the pull and shear tests. The aims of the finite element modelling have been to predict the reduction of test maximum load in defective ball bonds and the crack growth angle adopting a mixed-mode criterion. Good results have been obtained by the numerical fracture analysis, which can then support the reliability characterization and mechanical improvement of the bond. KW - Copper wire bonding KW - Mixed-mode crack growth KW - Silicon cratering KW - Stress intensity factor PY - 2014 DO - https://doi.org/10.1016/j.microrel.2014.04.004 SN - 0026-2714 VL - 54 IS - 11 SP - 2501 EP - 2512 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-32381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scolavino, L. A1 - Beretta, S. A1 - Madia, Mauro A1 - Zerbst, Uwe T1 - Critical speed of flawed rotors: global vs local approach N2 - The burst of a disc in rotating machinery can cause catastrophic damage of the equipment and, more importantly, it can represent a mortal threat to anyone in the sphere of influence of the event. In order to minimize the danger associated to a rotating component failure, burst testing is required by the authorities in order to set safety margins to the normal operating speeds. Moreover more accurate predicting tools are required for designing the components. This paper presents the results of a numerical and analytical study on the assessment of the crack driving force for discs containing surface flaws. The aim is to provide a simple, though reliable, tool in order to be able to calculate the possible dangerous in-service speed for a rotating component and, therefore, to set burst margins above the normal operating conditions of the equipment. An R6-like flaw assessment procedure is adopted considering different assumptions in the definition of the critical speed and the analytical predictions are compared with the results of elastic-plastic finite element analysis of disc. In particular, the validity and potentiality of the method is proved for surface flaws in different positions in the disc. T2 - ASME Turbo Expo 2014 - GT2014 CY - Düsseldorf, Germany DA - 16.06.2014 KW - Critical speed KW - Flawed rotors KW - Flaw assessment PY - 2014 SN - 978-0-7918-4576-9 DO - https://doi.org/10.1115/GT2014-26881 VL - 7A SP - 26881, 1 EP - 8 AN - OPUS4-32382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Arafah, D. A1 - Zerbst, Uwe T1 - Reference load solutions for plates with semi-elliptical surface cracks subjected to biaxial tensile loading N2 - The yield or limit load is a key parameter with respect to the accuracy of flaw assessment based on R6 type procedures such as the R6 routine, the SINTAP and FITNET method, the standard BS 7910 and others. In a number of previous papers two of the present authors proposed the use of a reference load instead of the common limit load, which not only provided more exact fracture mechanics predictions, but showed also a wider and more general application range than the conventional parameter. Here the method has been extended to biaxial tensile loading and it has been successfully validated by a thorough comparison with finite element results and alternative solutions available in the literature. KW - Flaw assessment KW - R6 procedure KW - Limit load KW - Reference load KW - Biaxial tensile loading PY - 2014 DO - https://doi.org/10.1016/j.ijpvp.2014.02.004 SN - 0308-0161 VL - 119 SP - 19 EP - 28 PB - Applied Science Publ. Ltd. CY - Barking AN - OPUS4-31429 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - A model for the determination of the fatigue life in technical alloys containing large and small defects T2 - ECF20 - European Conference on Fracture CY - Trondheim, Norway DA - 2014-06-30 PY - 2014 AN - OPUS4-31191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. T1 - A model for the determination of the fatigue life in technical alloys containing large and small defects N2 - The determination of the fatigue life in technical alloys containing large and small defects must rely on a propagation model which accounts for short and long crack growth. Recently an analytical model which incorporates propagation in the short crack regime and plastic correction for the crack driving force has been presented by two of the authors. This work is intended to show further validation of the model, taking into account data sets for different materials with different testing conditions. Despite the assumptions about missing parameters, the value of which had to be taken from the literature, the predictions showed a fairly good approximation of the fatigue lives. A possible interpretation of the results in terms of multiple crack initiation and propagation at higher loads is proposed. T2 - EFC20 - 20th European conference on fracture CY - Trondheim, Norway DA - 30.06.2014 KW - Fatigue strength KW - Crack propagation KW - Short cracks PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-311961 DO - https://doi.org/10.1016/j.mspro.2014.06.082 SN - 2211-8128 VL - 3 SP - 493 EP - 498 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-31196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Ermittlung der Schwingfestigkeit von technischen Legierungen mittels bruchmechanischer Methoden N2 - Die Arbeit beschreibt die Arbeitsphasen zur Entwicklung einer Prozedur zur bruchmechanischen Ermittlung der Schwingfestigkeit von technischen Legierungen. In dieser Hinsicht sind die experimentelle Ermittlung von Werkstoffkennwerten, die analytische Modellierung des Ermüdungsrisswachstums und eine ausreichende Validierung von Bedeutung. Um die Schwingfestigkeit von Komponenten adäquat ermitteln zu können, müssen die folgenden Aspekte in der Modellierung betrachtet werden: Die statistische Eingabe von Modellparametern, die Berücksichtigung von Kurzrisswachstum und ggf. die Mehrfachrisswachstum, bzw. die Rissinteraktion. T2 - DVM Fortbildungsseminar CY - Mittweida, Germany DA - 13.02.2017 KW - Schweißverbindungen KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS-Projekt PY - 2017 AN - OPUS4-39265 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro A1 - Vormwald, M. T1 - Schwingfestigkeit und Bruchmechanik N2 - Um bruchmechanisch Schwingfestigkeiten ermitteln zu können, sind einige Voraussetzungen erforderlich: (a) Das Wachstum sowohl langer als auch mechanisch und physikalisch kurzer Risse muss adäquat beschrieben werden. Das erfordert die Anwendung elastisch plastischer Konzepte zur Beschreibung der zyklischen Rissspitzenbeanspruchung sowie die Modellierung des graduellen Aufbaus der Rissschließeffekte im Kurzrissbereich. (b) Es müssen physikalisch sinnvolle Ausgangsrissgrößen für die bruchmechanische Analyse bestimmt werden. (c) Bei Spannungen oberhalb der Dauerfestigkeit respektive der Versagensspannung bei 107 Lastwechseln muss gegebenenfalls Mehrfachrisswachstum berücksichtigt werden. Der Vortrag diskutiert diese Punkte und zeigt Lösungswege auf. T2 - 49. Tagung des Arbeitskreises "Bruchmechanik und Bauteilsicherheit" CY - Mittweida, Germany DA - 14.02.2017 KW - Schwingfestigkeit KW - Bruchmechanik KW - Ausgangsriss KW - Mehrfachriss PY - 2017 VL - 249 SP - 77 EP - 92 PB - DVM (Deutscher Verband für Materialforschung und -prüfung) CY - Berlin AN - OPUS4-39227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Kiyak, Yusuf A1 - Zerbst, Uwe T1 - Extended parametric equations for weld toe stress concentration factors and through-thickness stress distributions in butt-welded plates subject to tensile and bending loading N2 - Based on a large set of 2D finite element analyses, parametric equations for weld toe stress concentration factors and through-thickness stress profiles are provided for butt-welded plates. These cover Single-Vand Double-V joints subject to tensile and bending loading. Compared to the most widespread solutions in the literature, which have also been tested against the finite element data in this work, the application range is extended particularly with respect to the weld toe radius(0.1≤ρ≤4 mm)andangle(10 °≤α≤60 °). Furthermore, two values of excess weld metal are considered (h=0.75;2.5mm). The analyses are performed for a plate thickness of 10 mm. Besides the extended validity range, the proposed equations show also an improved accuracy compared to the existing solutions. KW - Butt welds KW - Weld toes KW - Stress analysis KW - Structures PY - 2016 DO - https://doi.org/10.1007/s40194-016-0377-x VL - 60 IS - 6 SP - 1247 EP - 1259 AN - OPUS4-37959 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Ermittlung der Wöhlerkurve von Schweißverbindungen mittels bruchmechanischer Methoden N2 - In diesem Aufsatz wird eine analytische Prozedur zur bruchmechanischen Beschreibung des Schwingverhaltens von Schweißverbindungen beschrieben, die im Rahmen des DFG-AiF-Clusters IBESS entwickelt wurde. Es wurden drei Verbindungen untersucht (Stumpfstöße, Kreuzstöße und Längssteifen), die aus warmgewalzten Stahlplatten produziert wurden. Die analytische Modellierung basierte auf drei wichtigen Aspekten: Quantitative Beschreibung der Rissausbreitung mechanisch-kurzer Risse; Statistische Effekte infolge der Variabilität der lokalen Schweißnahtgeometrie; Modellierung der Mehrfachrissinitiierung und des Mehrfachrisswachstums. Im Folgenden wird die Methodik vorgestellt und ihre Validierung an einem ausgewählten Beispiel diskutiert. T2 - 43. Tagung des DVM-Arbeitskreises Betriebsfestigkeit CY - Steyr, Austria DA - 12.10.2016 KW - Schwingfestigkeit KW - Wöhlerkurve KW - Bruchmechanik KW - Schweißverbindung PY - 2016 AN - OPUS4-37859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kiyak, Yusuf A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Schork, B. T1 - Ermittlung der Wöhlerkurve von Schweißverbindungen mittels bruchmechanischer Methoden N2 - In diesem Aufsatz wird eine analytische Prozedur zur bruchmechanischen Beschreibung des Schwingverhaltens von Schweißverbindungen beschrieben, die im Rahmen des DFG-AiF-Clusters IBESS entwickelt wurde. Es wurden drei Verbindungen untersucht (Stumpfstöße, Kreuzstöße und Längssteifen), die aus warmgewalzten Stahlplatten produziert wurden. Die analytische Modellierung basierte auf drei wichtigen Aspekten: Quantitative Beschreibung der Rissausbreitung mechanisch-kurzer Risse; Statistische Effekte infolge der Variabilität der lokalen Schweißnahtgeometrie; Modellierung der Mehrfachrissinitiierung und des Mehrfachrisswachstums. Im Folgenden wird die Methodik vorgestellt und ihre Validierung an einem ausgewählten Beispiel diskutiert. T2 - 43. Tagung des DVM-Arbeitskreises Betriebsfestigkeit CY - Steyr, Austria DA - 12.10.2016 KW - Schwingfestigkeit KW - Wöhlerkurve KW - Bruchmechanik KW - Schweißverbindung PY - 2016 SN - 0944-522 SP - 197 EP - 208 AN - OPUS4-37866 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Zerbst, Uwe A1 - Ainsworth, R. A. A1 - Madia, Mauro ED - Klingbeil, D. ED - Vormwald, M. ED - Eulitz, K.-G. T1 - Reference load versus limit load in engineering flaw assessment: A proposal for a hybrid analysis option N2 - The net section limit load FY is a key input parameter for the accuracy of any elastic-plastic flaw assessment procedure of the R6 type. Unfortunately available limit load solutions are of variable quality since they have been obtained over decades by different methods. As a consequence the results of the fracture analyses such as the critical load or crack size are limited in their accuracy and are often significantly conservative. A further problem is that common limit load solutions based on ligament yielding are inadequate in a number of cases even for through crack configurations and should be replaced by some kind of local yielding solutions. In the present paper a simple and straightforward reference load definition is proposed instead of the limit load which strictly corresponds to a ligament yielding parameter Lr = 1 in the R6 Routine and similar approaches such as SINTAP and FITNET. This can be determined by finite element simulation for any geometry. In addition to a previous study on thin wall notched plates the method is applied to plates containing shallow semi-elliptical surface cracks. The results demonstrate that the approach provides a suitable extension and improvement of the existing methods. T2 - 18th European conference on fracture (ECF 18) - Fracture of materials and structures from micro to macro scale CY - Dresden, Germany DA - 2010-08-30 KW - Flaw assessment KW - Reference stress method KW - R6 procedure KW - EPRI method KW - SINTAP KW - FITNET KW - Limit load KW - Reference load PY - 2010 SN - 978-3-00-031802-3 IS - Paper 81 SP - 1 EP - 11 AN - OPUS4-22329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Ainsworth, R. A. A1 - Madia, Mauro T1 - Grenzlast oder Referenzlast? - Vorschlag für eine hybride Vorgehensweise bei der elastisch-plastischen Bauteilbewertung T2 - 42. Tagung des DVM-Arbeitskreises Bruchvorgänge - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Paderborn, Deutschland DA - 2010-02-23 KW - Bruchmechanische Bauteilbewertung KW - EPRI-Methode KW - Referenzspannungsmethode KW - R6-Routine KW - SINTAP KW - FITNET KW - FKM-Richtlinie KW - Grenzlast KW - Referenzlast PY - 2010 SP - 183 EP - 194 AN - OPUS4-22493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -