TY - CONF A1 - Feldkamp, Martin T1 - Evaluation of Heat Fluxes in Fire Reference Test Conducted in BAM Propane Gas Fire Test Facility N2 - Packages for the transport of intermediate- and high-level radioactive waste are designed to withstand severe accidents. The International Atomic Energy Agency (IAEA) has established specific mechanical and thermal tests. Packages for the transport of radioactive material must withstand these tests to comply with the Regulations for the Safe Transport of Radioactive Materials IAEA [IAEA (2018)]. A fire reference package was developed with the primary objective to demonstrate that the fire meets the regulatory requirements. Another aim is to characterise the boundary conditions of the actual fire as input parameters for thermo-mechanical simulations. A simple method to characterise the boundary conditions of a real steady state fire with a fire reference package is presented. The thermal test mainly consists of a 30 minute fully engulfing 800°C pool fire or an equally severe fire, such as a propane gas fire. The fire reference tests are performed prior to the actual fire test with the real package. The heat fluxes into the package depend substantially on the fire characteristics and the surface temperature of the package. To investigate local and overall heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for repeated use. The fire reference package presented in this paper represents the outer geometry of a small transport container for radioactive material and is used as a device in civil engineering. It is designed as a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 182 mm and a diameter of 102 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Open-air fire tests were performed in a BAM propane gas fire test facility with the fire reference package. The measured temperatures are used to determine the changes of heat fluxes into the fire reference package in relation to the package surface temperature. The calculated heat fluxes allow its fitting to express the thermal exposure as simple mathematical boundary condition. Therefore, in a first approach, fire properties such as adiabatic surface temperature (AST) as proposed by Wickström et al. (2007), convection coefficient and emissivity are determined mathematically fitting the heat flux development presented in this paper. The evaluated results provide an initial picture of local fire characteristics of the conducted propane gas fire and are a further development of previous works from Feldkamp et al. (2020). The results can be used in thermal and thermo-mechanical models to simulate the load on the real transport package in fire. The test shows that the examined propane gas fire covers the IAEA-fire over a wide range of surface temperatures with the chosen test stand parameters. T2 - SMiRT 27 (27th conference on Structural Mechanics in Reactor Technology) CY - Yokohama, Japan DA - 03.03.2024 KW - Fire KW - Propane KW - Fire Reference Test PY - 2024 AN - OPUS4-59680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Digitisation of the quality infrastructure - Using the example of additive manufacturing N2 - Rapidly advancing technologies and progressive digitisation are posing challenges to the established quality infrastructure (QI). In response, the key stakeholders of the German QI established the initiative QI-Digital aimed at developing new solutions for modern quality assurance. One of the central use cases herein is quality assurance for additive manufacturing, in which a fully interlinked additive manufacturing process chain is established. The intention is to collect and process data from each production step, allowing for a comprehensive digital view of the physical material flow. Within this process chain, prototypes of digital QI tools like machine readable standards and digital quality certificates are being demonstrated, tested, and evolved. This is complemented by research on the process level, comprising the evaluation and refinement of methods for in-situ and ex-situ quality assurance, as well as algorithms for registration, reduction, and analysis of process data. This paper presents the status, goals, and vision for the QI-Digital use case additive manufacturing. T2 - Metal Additive Manufacturing Conference 2023 CY - Vienna, Austria DA - 17.10.2023 KW - Additive Manufacturing KW - Digitalisation KW - Quality Assurance PY - 2023 AN - OPUS4-58629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Eine digitale QI für die moderne Produktion: Datenbasierte Qualitätssicherung in der Additiven Fertigung N2 - Als Beispiel für moderne Produktion ist die additive Fertigung (ugs. „3D-Druck“) bei der Herstellung von hochkomplexen metallischen Bauteilen, bionisch inspiriertem Leichtbau oder Prototypen nicht mehr wegzudenken. Die Qualitätssicherung (QS) von Bauteilen für sicherheitskritische Anwendungen stellt jedoch noch eine Herausforderung dar. Die Additive Fertigung (AM) ist ein vergleichsweise junges und datenintensives Fertigungsverfahren. Daher ist es ideal geeignet, die neuen Werkzeuge einer digitalen Qualitätsinfrastruktur (QI) für die moderne Produktion zu erproben und weiterzuentwickeln. T2 - 2. QI-Digital Forum CY - Berlin, Germany DA - 10.10.2023 KW - Additive Manufacturing KW - Digitalisation KW - Quality Assurance PY - 2023 AN - OPUS4-58630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Fire Reference Tests for Qualification of IAEA Fire N2 - A small cylindrical fire reference package was designed. A fire test setup was created using the fire reference package in accordance with IAEA standards. Four propane gas fire tests were conducted to determine heat fluxes into the fire reference package. The initial test setup was modified to create the final design of the fire test facility. This allowed for the heat flux to be adjusted to meet the regulatory IAEA fire qualification criteria. Furthermore, a numerical model of the fire reference package was created using boundary conditions derived from the experimental data. The simulation results demonstrated good agreement with the experimental data and provided additional insights. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Cadarache, France DA - 13.10.2022 KW - Fire KW - IAEA KW - Propane PY - 2022 AN - OPUS4-57251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Digitalisierung in der Additiven Fertigung N2 - Die Entwicklung einer digitalen QI ermöglicht die objektive Qualitätssicherung in der Additiven Fertigung und macht die Technologie gerade auch für kleine und mittelständische Unternehmen besser nutzbar. Sie wird vollwertig im Rahmen des Qualitätsanspruchs „Made in Germany“ einsetzbar – gerade auch beim Umbruch in Industriezweigen. Der Vortrag gibt Einblicke in aktuelle Arbeiten und die Ziele des Use Case Additive Fertigung. T2 - LEF-Themenwoche, Bayerisches Laserzentrum CY - Online meeting DA - 21.03.2023 KW - Digitalisierung KW - Qualitätsinfrastruktur KW - Additive Fertigung KW - Qualitätssicherung PY - 2023 AN - OPUS4-57186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Digitale Qualitätssicherung in der Additiven Fertigung und Voraussetzungen in der Qualitätsinfrastruktur N2 - Der Vortrag gibt einen Überblick über die Aktivitäten im QI-Digital Use Case Additive Fertigung, den aktuellen Stand und nächste Schritte. Es wurde eine digitale Prozesskette für den PBF-LB/M Prozess aufgebaut. Hier werden Daten entlang der gesamten Fertigungsstrecke gesammelt, ausgewertet und zur Qualitätssicherung weiterverarbeitet. Die grundlegende Datenstruktur wurde in die Normung überführt. T2 - TÜV SÜD Fachtagung: Additive Fertigung von Druckgeräten CY - Munich, Germany DA - 17.09.2024 KW - Digitalisierung KW - Qualitätsinfrastruktur KW - Additive Fertigung PY - 2024 AN - OPUS4-61089 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Eine digital gestützte Qualitätssicherung für die additive Fertigung N2 - Die Digitalisierung der Qualitätsinfrastruktur (QI) am Beispiel der Additiven Fertigung. Der Vortrag erörtert, wie die Elemente einer digitalen QI zur Qualitätssicherung und Zertifizierung in der Additiven Fertigung beitragen können. T2 - Treffen der Arbeitsgemeinschaft Additive Fertigung des VDMA CY - Coburg, Germany DA - 27.10.2022 KW - Qualitätsinfrastruktur KW - Additive Fertigung KW - Digitalisierung PY - 2022 AN - OPUS4-56165 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des WIPANOVerbundforschungsvorhabens GELELEK: Forschungsziele und Ergebnisse N2 - Der Vortrag stellt das WIPANO-Forschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - Sitzung des GfKORR Arbeitskreises „Korrosion und Korrosionsschutz von Eisen und Stahl“ CY - Online meeting DA - 08.12.2022 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - WIPANO KW - Zink KW - Korrosion PY - 2022 AN - OPUS4-56502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Stainless steels: Fundamentals and causes for corrosion defects N2 - The presentation gives an overview about the fundamentals on stainless steels. The mechanism of passive layer formation is explained and strategies for securing corrosion protection are given. The influence of a grinding process on corrosion resistance is discussed. T2 - Tech-Day Mettler Toledo CY - Online meeting DA - 23.11.2022 KW - Corrosion KW - Stainless steel KW - Grinding KW - KorroPad KW - Surface PY - 2022 AN - OPUS4-56370 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Digitalisierung der Qualitätsinfrastruktur am Beispiel der Additiven Fertigung N2 - Die Digitalisierung der Qualitätsinfrastruktur (QI) am Beispiel der Additiven Fertigung. Der Vortrag erörtert, wie man mit Elementen einer digitalen QI (DPP, DCoC, Smart Standard, DCC, etc.) aktuelle Herausforderungen in der Qualitätssicherung additiv gefertigter Bauteile adressieren kann. T2 - FORUM Qualitätssicherung in der additiven Fertigung – Quality Engineering CY - Online meeting DA - 13.09.2022 KW - Additive Fertigung KW - Qualitätssicherung KW - Digitalisierung KW - Qualitätsinfrastruktur PY - 2022 AN - OPUS4-56383 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Combustion Chamber Design for Encapsulated Wood-Component Testing N2 - eavy-weight packages for the safe transport of radioactive material are equippedwith impact limiters often built ofwood-filled steel sheet structures to fulfil the requirements of the International Atomic Energy Agency (IAEA) regulations. The requirements definemechanical tests followed by a thermal test, including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Impact limiters are a package component mainly designed for the packages to withstand severe mechanical accident scenarios. In drop tests the impact limiters absorb the kinetic energy during impact of the package. The package must then - with its pre-damaged impact limiters - endure a thermal test defined precisely in the IAEA regulations as a 30-min fully engulfing 800 °C-fire. After the fire, a wood-filled impact limiter may continue to release thermal energy from an ongoing combustion process, defining relevant package temperatures. The energy flow from a possible burning impact limiter to the package is important for the safety evaluation of transport packages. To investigate the combustion behaviour of densely packed layers of spruce wood, encapsulated in pre-damaged cylindrical metal enclosures, a test set-up has been realised. The set-up consists of a combustion chamber to perform these tests under defined boundary conditions. The temperature development of the test specimens will be observed fromoutside with a thermographic imager, with HD-Cameras, and the mass loss will be measured during the entire test. Airflow conditions in the combustion chamber are analysed using Computational Fluid Dynamics (CFD) calculations in OpenFOAM. The planned combustion test setup is described. T2 - Wood & Fire Safety 2024 CY - Štrbské Pleso, Slovakia DA - 12.05.2024 KW - IAEA KW - Combustion Chamber KW - Smouldering KW - Wood PY - 2024 AN - OPUS4-60227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten an natürlich gebildeten Zinkdeckschichten N2 - Ein neuer Ansatz bei elektrochemischen Korrosionsuntersuchungen kann durch den Einsatz von gelartigen Elektrolyten als Alternative zu wässrigen Prüfelektrolyten beschritten werden. Gelartige Elektrolyte ermöglichen minimalinvasive Untersuchungen an natürlich gebildeten Zinkdeckschichten. Dadurch können korrosionsrelevante Kennwerte ermittelt werden, die Aussagen zur Deckschichtbildung und zur Stabilität der gebildeten Deckschichten erlauben. In diesem Beitrag wird anhand verschiedener Deckschichtzustände an Zink der Mehrwert von gelartigen Elektrolyten für die Korrosionsforschung verdeutlicht. T2 - Tagung Werkstoffprüfung 2016 CY - Neu-Ulm, Germany DA - 01.12.2016 KW - Zinkdeckschichten KW - Zinc coatings KW - Korrosionsprüfung KW - Corrosion-testing KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Deckschichtbildung KW - Layer formation PY - 2016 AN - OPUS4-38571 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Corrosion investigations on zinc coatings by using gel-type electrolytes N2 - In the presentation different zinc coatings are presented and investigated. Their naturally formed protective layers are electrochemically characterized and corrosion relevant values are determined by using a gel pad based on polysaccharide. The corrosion relevant values allow the differentiation of various zinc coating systems and can describe the current protective effect provided by the coating. It is shown that gel-type electrolytes influence protective layers and coatings considerably less than corresponding bulk electrolytes. From the results it is evident that gel-type electrolytes represent a viable and promising field in corrosion research. T2 - 7th Kurt-Schwabe-Symposium CY - Mittweida, Germany DA - 04.09.2016 KW - zinc coatings KW - gel-type electrolytes KW - corrosion investigations PY - 2016 AN - OPUS4-37409 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen an Verzinkungen mit gelartigen Prüfelektrolyten N2 - Anhand von auf Polysaccharid basierenden Gelpads werden im Vortrag verschiedene Zinkschichtsysteme untersucht, die natürlich gebildeten Deckschichten elektrochemisch charakterisiert und korrosionsrelevante Kennwerte bestimmt. Die ermittelten Kennwerte erlauben eine Differenzierung verschiedener Schichtsysteme und können die momentane Schutzwirkung der Deckschichten unter atmosphärischen Bedingungen beschreiben. Durch den Vergleich zu Bulk-Elektrolyten wird gezeigt, dass gelartige Elektrolyte Zinkschichten deutlich geringer beeinflussen als entsprechende Bulk-Elektrolyte. Aus den Ergebnissen wird ersichtlich, dass gelartige Elektrolyte in der Korrosionsforschung ein entwicklungsfähiges und aussichtsreiches Forschungsfeld zur Beurteilung von Verzinkungen darstellen. T2 - Oberflächentage 2016 CY - Garmisch-Partenkirchen, Germany DA - 21.09.2016 KW - Korrosionsuntersuchungen KW - Corrosion investigations KW - Verzinkungen KW - Zinc coatings KW - Gelartige Elektrolyte KW - Gel-type electrolytes PY - 2016 AN - OPUS4-37497 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Behaviour of Wood Filled Impact Limiters during Fire Test N2 - Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by steel sheets. These impact limiters shall ensure the transport cask meets the mechanical and thermal IAEA regulatory test requirements. After damage caused by the mechanical tests the package has to withstand a severe fire scenario. According to the regulations during and following the thermal test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally. Corresponding to results of the French institute IRSN combustion and smouldering of wood inside the impact limiter occurred during and after the fire test. An additional energy supply from a pre-damaged impact limiter to the cask could be the consequence for the safety assessment of the containment. BAM started a first test phase to examine the issue of combustion for such kind of package components. The goal was to understand the phenomena under the consideration of relevant regulatory boundary conditions. Several metal buckets were filled with wood and equipped with thermocouples. The test specimens have been prepared with different damage arrangements to take the influence of the mechanical tests into account. This paper shows the experimental setup and the conduction of the tests. The first test shows that pre-damaged metal encapsulations can lead to smouldering of the wood and with this to a supplement energy release after the end of the 30 minute fire. BAM is in the preparation process for a second test phase. A thermal test will take place with a wood filled test specimen weighing about 2Mg. T2 - PATRAM 2016 CY - Kobe, Japan DA - 18.09.2016 KW - Burning KW - Fire test KW - Impact limiter KW - Shock absorber KW - Thermal test KW - Typ-B KW - Wood KW - Smouldering KW - Large scale testing PY - 2016 AN - OPUS4-37842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Untersuchungen zur Versalzung von Metalloberflächen im maritimen Bereich N2 - Die Versalzung und Verunreinigung von Metalloberflächen durch chloridhaltige Aerosole hat eine große Bedeutung für das Korrosionsverhalten von beschichteten Metalloberflächen im maritimen Bereich und bei Offshore-Anwendungen. So ist z. B. zu klären, ob und in welchem Maße eine Versalzung der Oberfläche Einfluss auf die Haftung und Dauerhaftigkeit von Beschichtungen hat. Dafür sind Detailfragen zu klären, etwa mit welcher Versalzung nach welchem Zeitraum zu rechnen ist oder wie für systematische Untersuchungen eine definierte und reproduzierbare Versalzung im Labor nachgestellt werden kann. Der Beitrag widmet sich diesen Fragestellungen. Es werden Ergebnisse eines Feldversuches auf Helgoland gezeigt und ein einfaches Verfahren zur definierten Beladung von Metalloberflächen mit Chloriden im Labormaßstab vorgestellt. T2 - 17. Tagung "Korrosionsschutz in der maritimen Technik" CY - Hamburg, Germany DA - 24.01.2018 KW - Maritime Atmosphäre KW - Maritime atmosphere KW - Versalzung KW - Salinization PY - 2018 AN - OPUS4-43936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Prüfverfahren zur Bewertung der kathodischen Enthaftung bei organischen Beschichtungen – Eine kritische Betrachtung N2 - Im Vortrag werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich ausgelotet. T2 - Arbeitskreissitzung „Korrosionsuntersuchung und -überwachung“ des GfKORR e. V. CY - Magdeburg, Germany DA - 21.11.2017 KW - Kathodische Enthaftung KW - Cathodic delamination KW - Korrosionsprüfung KW - Corrosion testing KW - Organische Beschichtungen KW - Organic coatings PY - 2017 AN - OPUS4-43038 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung der Korrosionsuntersuchungen im Rahmen des Themenfeldprojektes LeBeWind an der BAM N2 - Im Vortrag wird das Teilprojekt Korrosion des Themenfeldprojektes LeBeWind vorgestellt. Dabei werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich hinterfragt. Zusätzlich werden die Problemstellungen bei der Versalzung von metallischen Oberflächen im maritimen und Offshore-Bereich betrachtet. T2 - Arbeitskreissitzung „Korrosionsschutz von Windenergieanlagen“ des GfKORR e. V. CY - Bremen, Germany DA - 29.11.2017 KW - Kathodische Enthaftung KW - Cathodic delamination KW - Korrosionsprüfung KW - Corrosion testing KW - Organische Beschichtungen KW - Organic coatings PY - 2017 AN - OPUS4-43231 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Aspects of Assessment of Packages with Wood Filled Impact Limiters during Fire Tests N2 - Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by steel sheets. These impact limiters shall ensure that the transport casks meet the mechanical and thermal IAEA regulatory test requirements. According to the accident conditions of transport it is mandatory to expose the specimens to a cumulative effect by mechanical and thermal impacts. The mechanical tests consist of a free drop from 9 m onto a flat unyielding target and a 1 m drop onto a puncture bar. After damage caused by mechanical test sequences the package has to withstand a severe fire scenario. Corresponding to the IAEA advisory material it is required that the impact attitudes for the 9 m drop test and for the puncture test have to be such as to produce maximum damage, taking into account the thermal test. Moreover, any damage, which would give rise to increased radiation or loss of containment or affect the confinement system after the thermal test, should be considered. During and following the thermal test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally. Different works from the French Institute for Radiological Protection and Nuclear Safety (IRSN) and BAM show that additional energy supply from a pre-damaged impact limiter to the cask could occur. This effect should be considered within the safety assessment of the containment. Thermal effects at the closure system of the cask, which might result in an elevated activity release, have to be excluded. BAM conducted small scale tests with wood filled metal buckets showing continuing combustion processes during the cooling down phase. These test results are presented. As not much is known about smouldering processes in wood filled impact limiters, it is highly complex to define pre-damage of impact limiters, which are conservative, regarding the maximum damaging energy flow from the impact limiter to the containment system. More research has to be done to develop models to examine the effects of smouldering impact limiters on the containment of packages for the transport of radioactive material. Aspects of assessment and its difficulties are shown. BAM as a competent authority for the approval of transport casks for radioactive material in Germany operates the test facilities to examine the issue of mechanical damage, combustion and heat transfer for such kind of package systems. For this purpose the knowledge from real drop tests with casks of a mass partly over 100 tons was transferred to a test application. A thermal test will take place with a wood filled test specimen with a diameter of about 2.3 meters. The aim is to understand the phenomena of smouldering under the consideration of relevant regulatory boundary conditions. The process of smouldering is described with regard to the requirements in the thermal assessment of safety of packages for the transport of radioactive material. Requirements concerning the pre-damage of packages for the maximum damage of impact limiters are discussed. Parameters influencing the smouldering process are identified. T2 - WM 2017 Conference CY - Phoenix, Arizona, USA DA - 05.03.2017 KW - Fire test KW - Wood KW - Combustion KW - Smouldering KW - Smoldering KW - Impact limiter KW - Shock absorber KW - Thermal test KW - IAEA PY - 2017 AN - OPUS4-43170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Wie sicher ist die Bestimmung des Selbstentzündungsverhaltens großer Feststoffschüttungen? N2 - Für die Klassifizierung sowie die sichere Handhabung und Nutzung von Chemikalien und anderen Stoffen wurden spezielle standardisierte Testmethoden entwickelt, die weltweit zum Einsatz kommen. Die Ableitung von Sicherheitsmaßnahmen durch Experten erfordert, dass aus diesen Untersuchungen verlässliche Daten gewonnen werden. Ringversuche sind ein wesentliches Element bei der Methodenentwicklung (-validierung) und für die Qualitätssicherung von Laboratorien. Die Testmethode DIN EN 15188:2007 dient der Bestimmung des Selbstentzündungsverhaltens von Schüttgütern und Stäuben. Experimentelle Grundlage für die Beschreibung des Selbstentzündungsverhaltens eines bestimmten Materials ist die Bestimmung der Selbstentzündungstemperaturen (TSE) von Proben verschiedener Größen mit Hilfe isoperiboler Warmlagerungsversuche. Die so ermittelten Versuchsdaten ergeben die Abhängigkeit der Selbstentzündungstemperaturen vom Lagervolumen. Zweck einer schrittweise aufgebauten Serie von Ringversuchen und internen Labortests war die Identifizierung von Schwächen der bestehenden Methode bzw. von in der Laborpraxis auftretenden Mängeln bei der Anwendung der Methode, die Validierung der modifizierten und verbesserten Methode sowie die Bestimmung einer allgemeingültigen (Mess-)Unsicherheit dieser modifizierten Methode. T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Nürnberg, Germany DA - 24.10.2017 KW - Selbstentzündung KW - Methodenvalidierung KW - Messunsicherheit KW - Ringversuche PY - 2017 AN - OPUS4-43064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bornemann-Pfeiffer, Martin T1 - Accelerating Chemical Process Development and Manufacturing – Design and Validation of an Integrated NMR Micro Mixer N2 - The future competitiveness of the process industry and their providers depends on its ability to deliver high quality and high value products at competitive prices in a sus-tainable fashion, and to adapt quickly to changing customer needs. The transition of process industry due to the mounting digitalization of technical devices and their pro-vided data used in chemical plants proceeds. Though, the detailed characteristics and consequences for the whole chemical and pharmaceutical industry are still unfore-seeable, new potentials arise as well as questions regarding the implementation. As the digitalization gains pace fundamental subjects like the standardization of device interfaces or organization of automation systems must be answered. Still, process in-dustry lack of sufficient system and development concepts with commercial advantage from this trend. Compared to traditional batch processes, intensified continuous production allows new and difficult to produce compounds with better product uniformity and reduced consumption of raw materials and energy. Flexible (modular) chemical plants can pro-duce various products using the same equipment with short down-times between campaigns, and quick introduction of new products to the market. Full automation is a prerequisite to realize such benefits of intensified continuous plants. In continuous flow processes, continuous, automated measurements and closed-loop control of the product quality are required. Consequently, the demand for smart sensors, which can monitor key variables like component concentrations in real-time, is increasing. Low-Field NMR spectroscopy presents itself as such an upcoming smart sensor1,2 (as addressed, e.g., in the CONSENS project3). Systems utilizing such an online NMR analyzer benefits through short development and set-up times when applied to modular production plants starting from a desired chemical reaction3. As an example for such a modular process unit, we present the design and validation of an integrated NMR micro mixer based on computational mod-elling suited for a desired chemical reaction. This method includes a proper design of a continuous reactor, which is optimized through computational fluid dynamics (CFD) for the demands of the NMR sensor as well as for the given reaction conditions. The system was validated with a chemical reaction process. References: [1] M. V. Gomez et al., Beilstein J. Org. Chem. 2017, 13, 285-300 [2] K. Meyer et al., Trends Anal. Chem. 2016, 83, 39-52 [3] S. Kern et al., Anal Bioanal Chem. 2018, 410, 3349-3360 T2 - Kolloquium Arbeitskreis Prozessanalytik CY - Hannover, Germany DA - 03.12.2018 KW - NMR KW - Reaction Monitoring KW - Digital Twin KW - Flow Chemistry KW - Process Analytical Technology PY - 2018 N1 - Geburtsname von Bornemann-Pfeiffer, Martin: Bornemann, M. - Birth name of Bornemann-Pfeiffer, Martin: Bornemann, M. AN - OPUS4-46972 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des Programms WIPANO sowie aktueller Projektskizzen der BAM im Fachbereich 7.6 N2 - Der Vortrag erläutert die Förderschwerpunkte der Förderinitiative WIPANO des BMWi und zeigt aktuelle Projektskizzen sowie Projekte des Fachbereiches 7.6. T2 - Arbeitskreissitzung „Korrosionsuntersuchung und -überwachung“ des GfKORR e. V. CY - Berlin, Germany DA - 08.10.2018 KW - Korrosion KW - Corrosion KW - Zink KW - Spannstahl KW - KorroPad PY - 2018 AN - OPUS4-46379 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Prüfverfahren zur Bewertung der kathodischen Enthaftung bei organischen beschichtungen – Eine kritische Betrachtung N2 - Im Vortrag werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich ausgelotet. T2 - Arbeitskreissitzung „Korrosionsschutz durch Beschichtungen“ des GfKORR e. V. CY - Dresden, Germany DA - 23.10.2018 KW - Kathodische Enthaftung KW - Cathodic delamination KW - Korrosionsprüfung KW - Corrosion testing KW - Organische Beschichtungen KW - Organic coatings PY - 2018 AN - OPUS4-46380 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Field exposure studies under sheltered and unsheltered conditions at different test sites in northern and eastern Germany N2 - A series of field exposure tests according to ISO 9223 and 9226 was carried out at different locations to determine the corrosivity of different test sites throughout northern and eastern Germany. Standard test specimens of steel, zinc, copper and aluminium were exposed to rural, city and maritime atmosphere at test sites of the Federal Institute for Materials Research and Testing. Test sites at city atmosphere comprised exposure on a rooftop, next to a highly frequented road and directly at a motorway. Exposure under maritime conditions was carried out at Heligoland in the North Sea and at the North Sea coastline on Sylt. The specimens were stored under sheltered and unsheltered conditions on each test site, respectively. Corrosion rates after the first year of field exposure were determined and used for the classification of the atmospheres and the test sites regarding the corrosivity. The presentation will show the results of the systematic study. First year corrosion rates for steel, zinc, copper and aluminium will be presented and discussed with respect to the type of material, the atmospheric conditions and the time of wetness at the test sites. In addition, the difference between sheltered and unsheltered conditions will be discussed. T2 - EUROCORR 2018 CY - Krakow, Poland DA - 09.09.2018 KW - Standardproben KW - Standard test samples KW - Freibewitterungsprüfung KW - Field exposure studies PY - 2018 AN - OPUS4-45941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Prüfverfahren zur Bewertung der kathodischen Enthaftung bei organischen Beschichtungen – Eine kritische Betrachtung N2 - Im Vortrag werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich ausgelotet. T2 - Arbeitskreissitzung des DIN-Arbeitskreises NA 002-00-07-17 AK „Elektrochemische Verfahren“ CY - Bremerhaven, Germany DA - 07.11.2018 KW - Kathodische Enthaftung KW - Korrosionsprüfung KW - Organische Beschichtungen KW - Cathodic delamination KW - Corrosion testing KW - Organic coatings PY - 2018 AN - OPUS4-46514 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Investigations of the burning behavior of transport package impact limiters and thermal effects onto the cask N2 - Accident safe packages for the transport of spent nuclear fuel and high-level waste shall fulfil international IAEA safety requirements. Compliance is shown by consecutive mechanical and thermal testing. Additional numerical analysis are usually part of the safety evaluation. For damage protection some package designs are equipped with wood filled impact limiters encapsulated by steel sheets. The safety of these packages is established in compliance with IAEA regulations. Cumulative mechanical and fire tests are conducted to achieve safety standards and to prevent loss of containment. Mechanical reliability is proven by drop tests. Drop testing might cause significant damage of the impact limiter steel sheets and might enable sufficient oxygen supply to the impact limiter during the fire test to ignite the wood filling. The boundary conditions of the fire test are precisely described in the IAEA regulatory. During the test the impact limiter will be subjected to a 30 minute enduring fire phase. Subsequent to the fire phase any burning of the specimen has to extinguish naturally and no artificial cooling is allowed. At BAM a large-scale fire test with a real size impact limiter and a wood volume of about 3m³ was conducted to investigate the burning behaviour of wood filled impact limiters in steel sheet encapsulation. The impact limiter was equipped with extensive temperature monitoring equipment. Until today burning of such impact limiters is not sufficiently considered in transport package design and more investigation is necessary to explore the consequences of the impacting fire. The objective of the large scale test was to find out whether a self-sustaining smouldering or even a flaming fire inside the impact limiter was initiated and what impact on the cask is resulting. The amount of energy, transferred from the impact limiter into the cask is of particular importance for the safety of heavy weight packages. With the intention of heat flux quantification a new approach was made and a test bench was designed. A first computational simulation of transport package temperatures taking into account the results of the conducted fire test was performed. T2 - IRSN Conference on Safe Transport of Radioactive Material CY - Fontenay aux Roses, France DA - 13.11.2018 KW - Impact limiter KW - Shock absorber KW - Smoldering KW - Smouldering KW - Burning KW - Thermal testing KW - BAM TTS KW - Combustion KW - Fire KW - Energy release KW - Thermal simulation KW - Heat emission KW - Radioactive KW - Transport KW - IAEA KW - Wood KW - Spruce wood KW - Lid temperature PY - 2018 AN - OPUS4-46882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Corrosion investigations on zinc coatings by using gel-type electrolytes N2 - A new approach to the assessment of the corrosion behaviour of zinc coatings under atmospheric conditions can be achieved using gel-type electrolytes as an alternative to standard aqueous test electrolytes. Gel-type electrolytes allow minimally invasive corrosion investigations on zinc coatings. They also provide the possibility to carry out corrosion investigations onsite. By using gel-type electrolytes corrosion-relevant characteristic values such as corrosion currents and polarization resistanc-es can be determined. These allow to describe the formation and the stability of the formed corrosion product layers under various climatic conditions. With this knowledge, a prediction of the zinc coating life cycle is possible. In this contribution, the value of gel-type electrolytes for corrosion research on zinc coatings is presented. T2 - Intergalva 2018 CY - Berlin, Germany DA - 17.06.2018 KW - Deckschichtbildung KW - Layer formation KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Korrosionsprüfung KW - Corrosion testing KW - Zinkdeckschichten KW - Zinc coatings PY - 2018 AN - OPUS4-45244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Lebensdauerabschätzung von Zink- und Zinklegierungsüberzügen durch elektrochemische Untersuchungen und strukturanalytische Beschreibung der gebildeten Deckschichten N2 - Der Vortrag stellt ein neuartiges Korrosionsprüfverfahren für Zinküberzüge auf Basis gelartiger Elektrolyte vor und führt die Vorteile gegenüber konventionellen Prüfverfahren auf. Basierend auf den Ergebnissen wird die Idee für einen IGF-Projektantrag in Kooperation mit dem Fraunhofer IKTS vorgestellt. T2 - Arbeitskreissitzung der GfKORR, AK "Zink und Zinküberzüge" CY - Iserlohn, Germany DA - 25.04.2018 KW - Deckschichtbildung KW - Layer formation KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Korrosionsprüfung KW - Corrosion testing KW - Zinkdeckschichten KW - Zinc coatings PY - 2018 AN - OPUS4-44811 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Martin T1 - Fire phenomena of rigid polyurethane foams N2 - This work investigates the fire phenomena of rigid polyurethane foams (RPUF) in detail. To elucidate structure-property relationships systematically varied sets of foams were prepared. RPUF were synthesized with different densities using water and pentane as blowing agent. What is more, a flame retarded RPUF and rigid polyisocyanurate-polyurethane foams were examined. The comprehensive understanding of the processes taking place during combustion is the foundation of customized development of successful flame retardant approaches. Advanced cone calorimeter investigations provide insight into the fire behavior under forced flaming conditions. Thermocouples in the inside of specimens give information about the temperature gradient and temperature of the pyrolysis zone during combustion. Furthermore, fire phenomena were characterized using SEM, LOI and thermal analysis. By using a multi-methodological approach and systematically varied sets of foam materials, new insights into the burning of RPUF were won. The detailed knowledge of fire phenomena is essential for future development of tailored flame retardant strategies for RPUF. T2 - 15th International Conference on Advances in Foam Materials & Technology, FOAMS 2017 CY - Bayreuth, Germany DA - 11.10.2017 KW - Foam KW - Cone calorimeter KW - Flame retardancy KW - Fire behaviour KW - Polyurethane PY - 2017 AN - OPUS4-42755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten an Zink - Eine innovative Prüfmethodik N2 - Ein neuer Ansatz bei elektrochemischen Korrosionsuntersuchungen kann durch den Einsatz von gelartigen Elektrolyten als Alternative zu wässrigen Prüfelektrolyten beschritten werden. Gelartige Elektrolyte ermöglichen minimalinvasive Untersuchungen an natürlich gebildeten Zinkdeckschichten. Dadurch können korrosionsrelevante Kennwerte ermittelt werden, die Aussagen zur Deckschichtbildung und zur Stabilität der gebildeten Deckschichten erlauben. In diesem Beitrag wird anhand verschiedener Deckschichtzustände an Zink der Mehrwert von gelartigen Elektrolyten für die Korrosionsforschung verdeutlicht. T2 - AK-Sitzung der GfKORR AK "Einstieg in die Korrosion" CY - Frankfurt a. M., Germany DA - 07.11.0217 KW - Deckschichtbildung KW - Layer formation KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Korrosionsprüfung KW - Corrosion testing KW - Zinkdeckschichten KW - Zinc coatings PY - 2017 AN - OPUS4-42775 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Experimental investigations of the burning behavior of transport package impact limiters and of fire spread impact onto the cask N2 - Accident safe packages for the transport of spent nuclear fuel and high-level waste shall fulfil international IAEA safety requirements. Compliance is shown by consecutive mechanical and thermal testing. Additional numerical analysis are usually part of the safety evaluation. For damage protection some package designs are equipped with wood filled impact limiters encapsulated by steel sheets. The safety of these packages is established in compliance with IAEA regulations. Cumulative mechanical and fire tests are conducted to achieve safety standards and to prevent loss of containment. Mechanical reliability is proven by drop tests. Drop testing might cause significant damage of the impact limiter steel sheets and might enable sufficient oxygen supply to the impact limiter during the fire test to ignite the wood filling. The boundary conditions of the fire test are precisely described in the IAEA regulatory. During the test the impact limiter will be subjected to a 30 minute enduring fire phase. Subsequent to the fire phase any burning of the specimen has to extinguish naturally and no artificial cooling is allowed. At BAM a large-scale fire test with a real size impact limiter and a wood volume of about 3m³ was conducted to investigate the burning behaviour of wood filled impact limiters in steel sheet encapsulation. The impact limiter was equipped with extensive temperature monitoring equipment. Until today burning of such impact limiters is not sufficiently considered in transport package design and more investigation is necessary to explore the consequences of the impacting fire. The objective of the large scale test was to find out whether a self-sustaining smouldering or even a flaming fire inside the impact limiter was initiated and what impact on the cask is resulting. The amount of energy, transferred from the impact limiter into the cask is of particular importance for the safety of heavy weight packages. With the intention of heat flux quantification a new approach was made and a test bench was designed. T2 - PVP2018 - Pressure, Vessels and Piping Conference 2018 CY - Prague, Czech Republic DA - 15.07.2018 KW - Smouldering KW - Impact limiter KW - Burning KW - Wood KW - Shock absorber KW - Fire testing KW - IAEA KW - Radioactive material KW - Large-scale fire test KW - Combustion PY - 2018 AN - OPUS4-45594 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Zuverlässigkeit von sicherheitstechnischen Kenndaten - Validierung von Prüfmethoden durch Ringversuche N2 - Chemikalien werden im Prüflabor auf ihre gefährlichen Eigenschaften getestet, um die Risiken bei deren Handhabung richtig abschätzen zu können. Dazu sind Prüfmethoden entwickelt und veröffentlicht worden, die heute weltweit Anwendung finden. Auf die Validität der jeweiligen Prüfmethode und richtige Durchführung der Prüfung und Bewertung im Laboratorium müssen sich Hersteller, Importeure, Händler, Arbeitgeber oder Verbraucher verlassen können. Die Bundesanstalt für Materialforschung und –prüfung (BAM), Berlin hat eine langjährige Erfahrung sowohl bei der Ermittlung und Bewertung der physikalischen Gefahren von Chemikalien als auch bei der Einstufung und Kennzeichnung nach dem Chemikalienrecht (z.B. gemäß REACH-VO, CLP-VO, Gefahrgutvorschriften u.a.). Es werden drei Poster präsentiert, welche einerseits kritisch die im Rahmen der chemikalienrechtlichen Verfahren von den Registranten vorgelegten Prüfergebnisse / Prüfberichte bewerten und andererseits die Zuverlässigkeit von verschiedenen Prüfmethoden einschätzen bzw. den Aufwand am Beispiel der Validierung einer konkreten Prüfmethode durch Ringversuche demonstrieren. REACH-Registrierungsdossiers z.B. werden mit der Softwareanwendung IUCLID (International Uniform Chemical Information Database) erstellt. Für die Behörden ist die Bewertung der Zuverlässigkeit mit den Informationen zu den Studien im IUCLID-Dossiers oftmals schwer nachvollziehbar. Bei der Bewertung der Verlässlichkeit der im Labor gewonnenen Prüfergebnisse spielen Ringversuche eine entscheidende Rolle. In den letzten 10 Jahren wurden von der BAM und der PTB Ringversuche zu verschiedenen Prüfmethoden durchgeführt. In allen Ringversuchen wurden deutliche Unterschiede zwischen den Ergebnissen der teilnehmenden Laboratorien festgestellt. Die Abweichungen der Prüfergebnisse wurden jedoch nicht nur durch Laborfehler, sondern auch durch Mängel der Prüfmethoden verursacht. Deshalb ist es wichtig zu wissen, wie gut die Prüfmethode ist, mit der ein Gefahrgut oder Gefahrstoff klassifiziert wird oder mit denen sicherheitstechnische Kenndaten bestimmt werden. Ringversuche werden bei der Methodenentwicklung und -validierung eingesetzt und können zur Ermittlung der Messunsicherheit genutzt werden. Validierungsberichte zu Prüfmethoden sorgen für Transparenz, sind für die Regulierung im Chemikalienrecht erforderlich und dienen auch dazu auf globaler Ebene gleiche Wettbewerbsbedingungen zu schaffen. Die BAM und die PTB unterstützen deshalb den weiteren Ausbau des Ringversuchsprogramms des im Jahr 2007 gegründeten Kompetenzzentrums zur Qualitätssicherung für Prüfungen von Gefahrgütern und Gefahrstoffen auf physikalische Gefahren (Centre for quality assurance for testing of dangerous goods and hazardous substances, CEQAT-DGHS, www.ceqat-dghs.bam.de). Dieses betreibt die BAM gemeinsam mit der PTB und der QuoData Gesellschaft für Qualitätsmanagement und Statistik mbH, Dresden. T2 - Behörden-Erfahrungsaustausch CY - Berlin, Germany DA - 04.06.2018 KW - REACH KW - CLP KW - Methodenvalidierung KW - Messunsicherheit KW - Ringversuch PY - 2018 AN - OPUS4-45809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bornemann-Pfeiffer, Martin T1 - Accelerating chemical process development and manufacturing – Design and validation of an integrated NMR micro mixer N2 - The future competitiveness of the process industry and their providers depends on its ability to deliver high quality and high value products at competitive prices in a sustainable fashion, and to adapt quickly to changing customer needs. The transition of process industry due to the mounting digitalization of technical devices and their provided data used in chemical plants proceeds. Though, the detailed characteristics and consequences for the whole chemical and pharmaceutical industry are still unforeseeable, new potentials arise as well as questions regarding the implementation. As the digitalization gains pace fundamental subjects like the standardization of device interfaces or organization of automation systems must be answered. Still, process industry lack of sufficient system and development concepts with commercial advantage from this trend. Intensified continuous processes are in focus of current research. Compared to traditional batch processes, intensified continuous production allows new and difficult to produce compounds with better product uniformity and reduced consumption of raw materials and energy. Flexible (modular) chemical plants can produce various products using the same equipment with short down-times between campaigns, and quick introduction of new products to the market. Full automation is a prerequisite to realize such benefits of intensified continuous plants. In continuous flow processes, continuous, automated measurements and closed-loop control of the product quality are required. Consequently, the demand for smart sensors, which can monitor key variables like component concentrations in real-time, is increasing. Low-Field NMR spectroscopy presents itself as such an upcoming smart sensor (as addressed, e.g., in the CONSENS project – http://www.consens-spire.eu/). Systems utilizing such an online NMR analyzer benefits through short development and set-up times when applied to modular production plants starting from a desired chemical reaction. As an example for such a modular process unit, we present the design and validation of an integrated NMR micro mixer based on computational modelling suited for a desired chemical reaction. This method includes a proper design of a continuous reactor, which is optimized through computational fluid dynamics (CFD) for the demands of the NMR sensor as well as for the given reaction conditions. The system was validated with a chemical reaction process. T2 - ProcessNet PAAT Jahrestreffen CY - Cologne, Germany DA - 12.11.2018 KW - NMR KW - Reaction monitoring KW - Digital twin KW - Flow chemistry KW - Process analytical technology PY - 2018 N1 - Geburtsname von Bornemann-Pfeiffer, Martin: Bornemann, M. - Birth name of Bornemann-Pfeiffer, Martin: Bornemann, M. AN - OPUS4-46579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des WIPANOVerbundforschungsvorhabens GELELEK: Forschungsziele und Ergebnisse N2 - Der Vortrag stellt das WIPANOForschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - 13. Sitzung des GfKORR Arbeitskreises „Korrosionsuntersuchung und -überwachung“ CY - Online meeting DA - 08.12.2021 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - Zink KW - WIPANO PY - 2021 AN - OPUS4-53946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - New findings on the formation of corrosion product layers on zinc in the atmosphere N2 - The presentation shows systematic investigations to describe the corrosion and corrosion product formation processes of pure zinc under the climatic conditions currently prevailing in the Federal Republic of Germany. The investigations in their entirety aim at questioning current and establishing new ways of looking at the formation of corrosion products of pure zinc under atmospheric corrosion conditions. Thus, they make a significant contribution in understanding corrosion protection by zinc and zinc coatings. In particular, the focus is placed on the initial stage of the corrosion product formation. A systematic investigation of this time range, which is characterized by very reactive corrosion products, is only made possible by using gel-type electrolytes. The short periods of time at the beginning of weathering is now measurable and their influence on the formation of corrosion products and the kinetics of layer formation describable. By combining the new electrochemical approach with gravimetric, microscopic and analytical methods, new insights could be gained both on a methodic and scientific level. T2 - EUROCORR 2021 CY - Online meeting DA - 20.09.2021 KW - Atmospheric Corrosion KW - Corrosion KW - Corrosion products KW - Gel-type electrolytes KW - Zinc PY - 2021 AN - OPUS4-53332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des Forschungsbeirats des Gemeinschaftsausschuss Verzinken e.V. CY - Online Meeting DA - 07.10.2021 KW - Atmosphärische Korrosion KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Zink PY - 2021 AN - OPUS4-53478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des WIPANO-Vorhabens GELELEK N2 - Der Vortrag stellt das WIPANO-Forschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - Sitzung des Forschungsbeirats des Gemeinschaftsausschuss Verzinken e.V. CY - Online meeting DA - 07.10.2021 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - Zink PY - 2021 AN - OPUS4-53479 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des GfKORR Arbeitskreises „Korrosion und Korrosionsschutz von Eisen und Stahl“ CY - Online meeting DA - 22.06.2021 KW - Atmosphärische Korrosion KW - Gelartige Elektrolyte KW - Deckschichtbildung KW - Zink PY - 2021 AN - OPUS4-52843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - New findings on the formation of corrosion product layers on zinc in the atmosphere N2 - The presentation shows systematic investigations to describe the corrosion and corrosion product formation processes of pure zinc under the climatic conditions currently prevailing in the Federal Republic of Germany. The investigations in their entirety aim at questioning current and establishing new ways of looking at the formation of corrosion products of pure zinc under atmospheric corrosion conditions. Thus, they make a significant contribution in understanding corrosion protection by zinc and zinc coatings. In particular, the focus is placed on the initial stage of the corrosion product formation. A systematic investigation of this time range, which is characterized by very reactive corrosion products, is only made possible by using gel-type electrolytes. The short periods of time at the beginning of weathering is now measurable and their influence on the formation of corrosion products and the kinetics of layer formation describable. By combining the new electrochemical approach with gravimetric, microscopic and analytical methods, new insights could be gained both on a methodic and scientific level. T2 - 2nd Task Group Meeting TC124 WG4-TC 250 SC5 Task Group Corrosion CY - Online Meeting DA - 06.05.2021 KW - Zinc KW - Corrosion products KW - Gel-type electrolytes KW - Corrosion KW - Atmospheric corrosion PY - 2021 AN - OPUS4-52604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des Forschungsvorhabens GELELEK N2 - Der Vortrag stellt das Forschungsvorhaben GELELEK im Rahmen der Ad hoc Gruppe "GELELEK" des DIN-Normenausschusses Materialprüfung (NMP) vor. T2 - Sitzung der Ad hoc Gruppe "GELELEK" im DIN-Normenausschuss Materialprüfung (NMP) CY - Online Meeting DA - 21.04.2021 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Zink PY - 2021 AN - OPUS4-52541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des GfKORR Arbeitskreises „Zink und Zinküberzügel“ CY - Online meeting DA - 28.09.2021 KW - Atmosphärische Korrosion KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Zink PY - 2021 AN - OPUS4-53410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Prozess- und materialbedingte Ursachen für Korrosionserscheinungen an nichtrostenden Stählen N2 - Der Vortrag beleuchtet prozess- und materialbedingte Ursachen für Korrosionserscheinungen an nichtrostenden Stählen. Der Fokus liegt auf dem Einfluss von Schleifprozessen. Es werden Maßnahmen erläutert, um die Korrosionsbeständigkeit der Oberfläche zu verbessern. T2 - 3M Webinar „Schleiftechnologien zur Korrosionsvermeidung und Produktivitätssteigerung“ CY - Online meeting DA - 25.03.2021 KW - Nichtrostender Stahl KW - Korrosion KW - Schleifprozesse PY - 2021 AN - OPUS4-52360 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Process- and material-related causes for corrosion defects on stainless steels N2 - The presentation provides information on process- and material-related causes for corrosion on stainless steels. The influence of surface grinding is discussed. Methods for enhancing the corrosion resistance of stainless steels are shown. T2 - 3M Webinar “Technologies, Tools & Tips to avoid corrosion on Stainless Steel” CY - Online meeting DA - 25.02.2021 KW - Stainless steel KW - Corrosion KW - Grinding processes PY - 2021 AN - OPUS4-52358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - New findings on the formation of corrosion product layers on zinc in the atmosphere N2 - The presentation shows systematic investigations to describe the corrosion and corrosion product formation processes of pure zinc under the climatic conditions currently prevailing in the Federal Republic of Germany. The investigations in their entirety aim at questioning current and establishing new ways of looking at the formation of corrosion products of pure zinc under atmospheric corrosion conditions. Thus, they make a significant contribution in understanding corrosion protection by zinc and zinc coatings. In particular, the focus is placed on the initial stage of the corrosion product formation. A systematic investigation of this time range, which is characterized by very reactive corrosion products, is only made possible by using gel-type electrolytes. The short periods of time at the beginning of weathering is now measurable and their influence on the formation of corrosion products and the kinetics of layer formation describable. By combining the new electrochemical approach with gravimetric, microscopic and analytical methods, new insights could be gained both on a methodic and scientific level. T2 - 26th International Galvanizing Conference and Exhibition CY - Rome, Italy DA - 20.06.2022 KW - Atmospheric Corrosion KW - Corrosion KW - Corrosion products KW - Gel-type electrolytes KW - Zinc PY - 2022 AN - OPUS4-55113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Forschungsprojekt RUNOFF: "Neubewertung der Dauerhaftigkeit von Dach- und Fassadenmaterialien und des Eintrags von Schwermetall-Ionen in die Umwelt hervorgerufen durch Runoff„ N2 - Bei Betrachtungen zur Lebensdauer von Metallbauteilen im Bauwesen müssen Korrosions- und Runoff-Vorgänge an der Atmosphäre als verschiedene Reaktionen unterschieden werden. Korrosion ist der Prozess, der von elektrochemischen Reaktionen an der Grenzfläche Metall/Patina kontrolliert wird. Runoff dagegen wird durch chemische Reaktionen an der Grenzfläche Patina/Atmosphäre begünstigt. Mit zunehmender Bewitterungszeit nimmt die Korrosionsgeschwindigkeit stetig ab, während postuliert wird, dass die Geschwindigkeit des Runoffs über die gesamte Zeit konstant bleibt. Dieses Verhalten des Runoffs muss aber zunehmend bezweifelt werden. Die Gesamtmenge an abgezehrtem Metall beinhaltet zwei Bestandteile. Ein Teil wird in die Schicht aus Korrosionsprodukten eingebaut, der andere wird aufgrund von Niederschlägen aus der Patina gelöst. Aus diesem Grund ist die Menge an Zink-Runoff stark abhängig von den Eigenschaften der Korrosionsprodukt- bzw. Patinaschicht und nicht anhand der Zusammensetzung des Metalls abschätzbar. Vorhandene Modelle können die Menge an Runoff, und damit verbunden die Abzehrung einer Schicht aus Zink und Kupfer, sowie den resultierenden Eintrag von Schwermetallionen in die Umwelt nicht mehr darstellen und erklären. Um den Korrosionsschutz an Bauwerken zum einen dauerhaft unter Beachtung von Kostenaspekten und Ressourcenschonung und zum anderen unter ökologischen Gesichtspunkten auslegen zu können, müssen deshalb neue wissenschaftliche Grundlagen erarbeitet und die Mechanismen beschrieben werden. Das BAM-Forschungsvorhaben RUNOFF widmet sich den Fragestellungen. Der Vortrag gibt einen kurzen Überblick zum Forschungsvorhaben. T2 - 19. Projektetage der Bauforschung CY - Online meeting DA - 22.03.2022 KW - Runoff KW - Zink KW - Korrosion KW - Kupfer PY - 2022 AN - OPUS4-54580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zum Korrosionsverhalten von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - 69. Sitzung des NA 062-01-71 AA "Korrosion und Korrosionsschutz" CY - Berlin, Germany DA - 27.02.2020 KW - Korrosion KW - Zink KW - Atmosphärische Korrosion KW - Korrosionsprüfung KW - Deckschichtbildung KW - gelartige Elektrolyte PY - 2020 AN - OPUS4-50479 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Beschreibung der Deckschichtbildung bei Zink und Zinklegierungen mittels minimalinvasiver Korrosionsuntersuchungen und analytischer Methoden (MINIMAL) N2 - Der Vortrag stellt ein neuartiges Korrosionsprüfverfahren für Zinküberzüge auf Basis gelartiger Elektrolyte vor und führt die Vorteile gegenüber konventionellen Prüfverfahren auf. Basierend auf den Ergebnissen wird die Idee für einen IGF-Projektantrag in Kooperation mit dem Fraunhofer IKTS vorgestellt. T2 - Web-Meeting GAV-Forschungsbeirat CY - Online meeting DA - 29.04.2020 KW - Deckschichtbildung KW - Zink KW - Korrosionsprüfung KW - Gelartige Elektrolyte PY - 2020 AN - OPUS4-50718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Auslagerungsversuche von Standardproben nach DIN EN ISO 9223 unter verschiedenen atmosphärischen Bedingungen N2 - Der Vortrag berichtet über die Auslagerung von Standardproben nach DIN EN ISO 9223 bis 9226 aus Zink, Stahl, Kupfer und Aluminium auf den verschiedenen atmosphärischen Bewitterungsständen der Bundesanstalt für Materialforschung und -prüfung (BAM). Im Vortrag werden die Masseverluste, Korrosionsgeschwindigkeiten und Korrosivitätskategorien der Standardproben im freibewitterten und überdachten Bereich nach einem Jahr vorgestellt und Unterschiede hinsichtlich der Atmosphärenbedingungen aufgezeigt. Freibewitterte Proben zeigen dabei deutliche Unterschiede hinsichtlich ihres Korrosionsverhaltens im Vergleich zu überdachten Proben. Die ermittelten Korrosivitätskategorien sind sowohl standort- als auch materialspezifisch. T2 - Gemeinsame Sitzung des GfKORR Arbeitskreises „Korrosionsschutz von Windenergieanlagen“ mit der Fachgruppe „Korrosionsschutz“ der WAB e.V. CY - Online meeting DA - 07.12.2020 KW - Atmosphärische Korrosion KW - Auslagerungsversuche KW - Freibewitterung KW - Korrosion PY - 2020 AN - OPUS4-51783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Brand- und Explosionsgefahren beim Umgang mit Metallstäuben T2 - Fortbildungsseminar Metallpulver - Erzeugen, Charakterisieren, Anwenden CY - Bremen, Deutschland DA - 2015-03-26 PY - 2015 AN - OPUS4-33005 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Martin-Sanchez, Pedro Maria T1 - Detection and quantification methods for material-colonizing microorganisms by pPCR: from rock paintings in Lascaux to photovoltaic panels T2 - DECHEMA /GfKORR-Fachgruppensitzung "Mikrobielle Materialzerstörung und Materialschutz" CY - Frankfurt am Main, Deutschland DA - 2014-10-17 PY - 2014 AN - OPUS4-33172 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Combustion of shock absorber under IAEA thermal test conditions - recent testing - T2 - IRSN/BAM-Workshop about fire testing CY - Paris, France DA - 2015-04-13 PY - 2015 AN - OPUS4-33143 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Optimierung industrieller Korundschleifprozesse zur Sicherstellung der Korrosionsbeständigkeit nichtrostender Stähle T2 - Arbeitskreissitzung des GfKORR e.V., Arbeitskreis "Korrosion und Korrosionsschutz von Eisen und Stahl" CY - Dortmund, Germany DA - 2014-12-11 PY - 2014 AN - OPUS4-32228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Wie man Brand- und Explosionsgefahren durch Stäube/chemische Verbindungen einschätzt und begegnet T2 - Förderprozess-Foren 2014 CY - Würzburg, Deutschland DA - 2014-11-18 PY - 2014 AN - OPUS4-32113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Ringversuch Messunsicherheit DIN EN 15188/Ergebnisse INS Projekt "Explodierender Draht" als alternative Zündquelle für die 20-l-Kugel T2 - 61. Industriearbeitskreis "Brennbare Stäube" CY - Ludwigshafen, Deutschland DA - 2014-06-24 PY - 2014 AN - OPUS4-32115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Sicherstellung des Korrosionsschutzes durch werkstoffgerechte Verarbeitung nichtrostender Stähle T2 - 23. Erfahrungsaustausch und Weiterbildung für Schweißaufsichtspersonen und Verantwortliche der werkseigenen Produktionskontrolle im bauaufsichtlichen Bereich der SLV Halle CY - Dresden, Germany DA - 2015-02-25 PY - 2015 AN - OPUS4-32715 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Sicherstellung des Korrosionsschutzes durch werkstoffgerechte Verarbeitung nichtrostender Stähle T2 - 23. Erfahrungsaustausch und Weiterbildung für Schweißaufsichtspersonen und Verantwortliche der werkseigenen Produktionskontrolle im bauaufsichtlichen Bereich der SLV Halle CY - Halle, Germany DA - 2015-02-26 PY - 2015 AN - OPUS4-32716 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Passivität und lokale Korrosionserscheinungen bei nichtrostenden Stählen T2 - Seminar Korrosion und Korrosionsschutz, Otto-von-Guericke-Universität Magdeburg CY - Magdeburg, Germany DA - 2014-11-07 PY - 2014 AN - OPUS4-31926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Grundlagen der Korrosion T2 - Seminar Korrosion und Korrosionsschutz, Otto-von-Guericke-Universität Magdeburg CY - Magdeburg, Germany DA - 2014-10-24 PY - 2014 AN - OPUS4-31911 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Sicherstellung des Korrosionsschutzes durch werkstoffgerechte Verarbeitung nichtrostender Stähle T2 - 23. Erfahrungsaustasch und Weiterbildung für Schweißaufsichtspersonen und Verantwortliche der werkseigenen Produktionskontrolle im bauaufsichtlichen Bereich, Nachfolgeseminar der GSI SLV Polska CY - Zabrze, Poland DA - 2015-06-02 PY - 2015 AN - OPUS4-33336 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Scheid, Marc T1 - Validation of the New Ignition Source "Exploding Wire" for Dust Explosion Testing in the 20-l-Sphere T2 - Hazards 24 CY - Edinburgh, Scotland DA - 2014-05-07 PY - 2014 AN - OPUS4-30690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Experimental fire testingof impact limiter of transport package for radioactive material T2 - Fire Science Workshop CY - Berlin, Germany DA - 2013-11-29 PY - 2013 AN - OPUS4-30977 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Self-ignition of bulk solids: laboratory tests - simulations - reality? T2 - Fire Science Workshop CY - Berlin, Germany DA - 2013-11-29 PY - 2013 AN - OPUS4-30978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Erzeugung korrosionoptimierter Oberflächen bei nichtrostenden Stählen mit industriellen Schleifprozessen T2 - Arbeitskreissitzung der GfKORR "Corrosion Monitoring und Prüf- und Untersuchungsmethoden" CY - Heligoland, Germany DA - 2014-05-12 PY - 2014 AN - OPUS4-30744 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Influence of heat treatment on corrosion resistance of martensitic stainless steels 1.4034 and 1.4021 T2 - EUROCORR 2014 CY - Pisa, Italy DA - 2014-09-08 PY - 2014 AN - OPUS4-31400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten zur Beschreibung der Korrosionsschutzwirkung von Zinküberzügen N2 - Ein neuer Ansatz bei elektrochemischen Korrosionsuntersuchungen kann durch den Einsatz von gelartigen Elektrolyten als Alternative zu wässrigen Prüfelektrolyten beschritten werden. Gelartige Elektrolyte ermöglichen minimalinvasive Untersuchungen an natürlich gebildeten Zinkdeckschichten. Dadurch können korrosionsrelevante Kennwerte ermittelt werden, die Aussagen zur Deckschichtbildung und zur Stabilität der gebildeten Deckschichten unter verschiedenen klimatischen Bedingungen erlauben. In diesem Beitrag wird anhand verschiedener Deckschichtzustände an Zink der Mehrwert von Untersuchungen mit gelartigen Elektrolyten für die Korrosionsforschung verdeutlicht. T2 - 16. Tagung "Korrosionsschutz in der maritimen Technik" CY - Hamburg, Germany DA - 25.01.2017 KW - Deckschichtbildung KW - Layer formation KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Korrosionsprüfung KW - Corrosion testing KW - Zinkdeckschichten KW - Zinc coatings PY - 2017 AN - OPUS4-39039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Brand- und Explosionsgefahren beim Umgang mit Metallstäuben N2 - Grundlagen des Brand- und Explosionsschutzes mit Schwerpunkt Metallstäube: - Gefahren - Prinzipien des Explosionsschutzes - Ableiten von Schutzmaßnahmen - Bestimmung der Stoffeigenschaften - Umgang mit entsprechenden Datenbanken T2 - DGM-Fortbildungsseminar "Metallpulver Erzeugen - Charakterisieren - Anwenden" CY - Bremen, Germany DA - 30.03.2017 KW - Brandschutz KW - Explosionsschutz KW - Sicherheitstechnische Kenngrößen PY - 2017 AN - OPUS4-39917 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Brand- und Explosionsgefahren beim Umgang mit nanoskalig hergestellten Materialien N2 - In vielen Bereichen der Industrie und im verarbeitenden Gewerbe werden eine Vielzahl brennbarer Stäube produziert, verarbeitet, transportiert oder anderweitig verwendet. Die Partikelgröße der Stäube übt einen entscheidenden Einfluss auf deren Brand- und Explosionsverhalten aus. Mit Abnahme der Partikelgröße nehmen die gefährlichen Auswirkungen im Falle einer Explosion sowie die Zündempfindlichkeit zu. Aufgrund besonderer Eigenschaften nanoskaliger Materialien hat die Produktion solcher Stäube mit sehr geringen Primärpartikelgrößen in den letzten Jahren zugenommen. Über das Brand- und Explosionsverhalten solcher Stäube war bis vor wenigen Jahren jedoch kaum bis wenig bekannt. Untersuchungen haben gezeigt, dass nanoskalig hergestellte Stäube im Fall einer Explosion nicht grundsätzlich heftiger reagieren als die kritischsten Mikrostäube. Dennoch reagieren sogenannte Nanostäube mitunter zündempfindlicher als vergleichbare Mikrostäube; vereinzelt wurden höhere Werte für den maximalen Explosionsdruck und zeitlichen Druckanstieg für vergleichbare Stäube mit mikroskaligen Partikeln festgestellt. Für die Praxis ist daher zu beachten, dass zündempfindliche Stäube dementsprechend transportiert und gehandhabt bzw. entsprechende Schutzmaßnahmen ergriffen werden. T2 - Tagung des Sachgebietes "Explosionsschutz" der deutschen gesetzlichen Unfallversicherung CY - Heidelberg, Germany DA - 24.11.2016 KW - Nanoskalige Stäube KW - Explosionseigenschaften KW - Zündverhalten PY - 2016 AN - OPUS4-39112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - LAUS – Large Aperture Ultraschall N2 - Prinzip und erste Anwendungsbeispiele eines neu entwickelten Ultraschall-Arrays für die bildgebende Echomessung an sehr dicken Betonbauteilen T2 - Fachtagung Bauwerksdiagnose CY - Berlin, Germany DA - 25.02.2016 KW - Ultraschall-Echo KW - Beton KW - Ultraschall-Array KW - Abbildungsverfahren PY - 2016 AN - OPUS4-38855 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Dynamische Anpassung der Tafelkonstanten unter Verwendung gelartiger Elektrolyte für die Bestimmung von Korrosionsraten an Zink N2 - Der Beitrag stellt eine neue Herangehensweise zur Bestimmung und Bewertung von Tafelfaktoren unter Verwendung gelartiger Elektrolyte und der Electrochemical Frequency Modulation (EFM) vor. Diese relativ neue elektrochemische Methode bietet die Möglichkeit, innerhalb einer Messung und in kurzen Messintervallen sowohl Polarisationswiderstände als auch Tafelfaktoren zu bestimmen. Ausgehend von einer umfassenden Parameterstudie wird gezeigt, dass ein direkter Zusammenhang zwischen den beiden Werten besteht, der mathematisch beschrieben werden kann. Die ermittelten B-Werte werden in diesem Beitrag vorgestellt und hinsichtlich ihrer Anwendbarkeit und Grenzen diskutiert. T2 - 19. Werkstofftechnisches Kolloquium der TU Chemnitz CY - Chemnitz, Germany DA - 16.03.2017 KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Zink KW - Zinc KW - Stearn-Geary-Konstante KW - Stern Geary constant PY - 2017 AN - OPUS4-39431 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Optimierung industrieller Korundschleifprozesse zur Sicherstellung der Korrosionsbeständigkeit nichtrostender Stähle N2 - Der Vortrag verdeutlicht die Grundlagen der Korrosionsbeständigkeit nichtrostender Stähle und beschäftigt sich vorwiegend mit dem Einfluss der Schleifbearbeitung auf das Korrosionsverhalten. Das AiF-Vorhaben 18823 N/1 wird vorgestellt und erste Ergebnisse zum Einfluss von Schleifprozessen auf die Korrosionsbeständigkeit nichtrostender Stähle werden präsentiert. Darüber hinaus werden Empfehlungen für Verarbeiter nichtrostender Stähle gegeben. T2 - Kursleiterfortbildung 2016 der Informationsstelle Edelstahl Rostfrei CY - Berlin, Germany DA - 26.09.2016 KW - Korrosionsbeständigkeit KW - Corrosion resistance KW - Schleifbearbeitung KW - Surface grinding KW - Nichtrostende Stähle KW - Stainless steels PY - 2016 AN - OPUS4-37517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Interlaboratory Test 2015 "EN 15188" - Ergebnisse und Schlussfolgerungen N2 - Ergebnisse des Ringversuches "DIN EN 15188: Determination of the spontaneous ignition behaviour of dust acuumulations T2 - Industriearbeitskreis "Brennbare Stäube" CY - Wolfgang-Hanau, Germany DA - 28.06.2016 KW - Selbstentzündung KW - Ringversuch KW - Methodenvalidierung KW - Messunsicherheit PY - 2016 AN - OPUS4-37196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Einfluss der Oberflächenausführung auf das Korrosionsverhalten nichtrostender Stähle T2 - Arbeitskreissitzung des GfKORR e.V., Arbeitskreis "Korrosion und Korrosionsschutz von Eisen uned Stahl" CY - Duisburg, Germany DA - 2015-06-10 PY - 2015 AN - OPUS4-33424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Elektrochemische Untersuchungen zum Einfluss von Verformungsmartensit auf das Korrosionsverhalten austenitisch nichtrostender Stähle T2 - AK-Sitzung der GfKORR AK "Korrosion und Korrosionsschutz von Eisen und Stahl" CY - Duisburg DA - 2015-12-08 PY - 2015 AN - OPUS4-35046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Ziel, methodisches Konzept und Ergebnisse des Interlaboratory test 2010/11 "DIN EN 15188:2007 - self ignition temperature" T2 - Kolloquium des Arbeitskreises "Brennbare Stäube": Interlaboratory test 2010/11 DIN EN 15188:2007 - self-ignition temperature" CY - Dresden, Deutschland DA - 2013-01-29 PY - 2013 UR - http://www.ceqat-dghs.bam.de/en/events/index.htm AN - OPUS4-33474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Combustion of wood encapsulated in steel sheets during fire test T2 - Ramtrans 2015, 10th International Conference on Radioactive Materials Transport and Storage CY - Oxford, UK DA - 2015-05-19 PY - 2015 AN - OPUS4-33449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - Ultrasonic testing of a sealing construction made of salt concrete in an underground disposal facility for radioactive waste T2 - NDT-CE 2015 CY - Berlin, Gemany DA - 2015-09-15 PY - 2015 AN - OPUS4-34443 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dümmel, Martin T1 - Tumbling effects of cylindrical shells N2 - In the future new types of lift charges for display Shells will enter the market. These types may not be based on black powder and therefore will show different Performance behaviors. The European standard series EN 16261 deals with the testing and assessment of display fireworks in order to satisfy the essential safety requirements which have to be met before placing these items on the EU market. The aim of the study is to investigate how certain types of lift charges (NC based) influence the lift, tumbling and drift of cylindrical shells. In consequence, if the performance characteristics deviate strongly from those of typical black powder, safety related regulations in the EU and Germany might be affected, as well. T2 - 16th International Symposium on Fireworks CY - Omagari, Japan DA - 24.04.2017 KW - Fireworks KW - Shells KW - Tumbling PY - 2017 AN - OPUS4-40610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Selbstentzündung von Feststoffen: EN 15188, metallurgische Kohlen, Holzpellets N2 - Berichtet wird über geplante Änderungen der europäischen Norm EN 15188 "Bestimmung des Selbstentzündungsverhaltens von Schüttgütern und Stäuben"; basierend auf den von der BAM durchgeführten Ringversuchen zur Methodenvalidierung. Zusätzlich wird berichtet von Besonderheiten bei der Gefahrguteinstufung metallurgischer Kohlen als selbsterhitzungsfähiger Feststoff sowie der Selbstentzündung von Holzpellets. T2 - Treffen des Industriearbeitskreises "Brennbare Stäube",Insitut für Arbeitsschutz und Arbeitssicherheit CY - St. Augustin, Germany DA - 20.06.2017 KW - Selbstentzündung KW - Gefahrstoff KW - Einstufung KW - Feststoff PY - 2017 AN - OPUS4-41048 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten zur Beschreibung der Korrosionsschutzwirkung von Zinküberzügen N2 - Ein neuer Ansatz bei elektrochemischen Korrosionsuntersuchungen kann durch den Einsatz von gelartigen Elektrolyten als Alternative zu wässrigen Prüfelektrolyten beschritten werden. Gelartige Elektrolyte ermöglichen minimalinvasive Untersuchungen an natürlich gebildeten Zinkdeckschichten. Dadurch können korrosionsrelevante Kennwerte ermittelt werden, die Aussagen zur Deckschichtbildung und zur Stabilität der gebildeten Deckschichten erlauben. Der Vortrag stellt das Promotionsthema vor und erläutert die Untersuchungsschwerpunkte. T2 - 16. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik - Doktorandenkolloquium CY - Magdeburg, Germany DA - 08.09.2017 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsprüfung KW - Zinkdeckschichten KW - Corrosion testing KW - Gel-type electrolytes KW - Layer formation KW - Zinc coatings PY - 2017 AN - OPUS4-41897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Characterization of gas sorption in glassy polymers combining experimental and molecular modeling techniques T2 - American Chemical Society (ACS) Spring Meeting CY - New Orleans, LA, USA DA - 2008-04-06 PY - 2008 AN - OPUS4-17402 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Brennbare Schüttgüter und Stäube - Brand- und Explosionsgefahren richtig bewerten T2 - DECHEMA Weiterbildungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2008-10-22 PY - 2008 AN - OPUS4-18006 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - Features for ultrasonic imaging of concrete elements: Phase evaluation and air coupled ultrasound T2 - 12th International Conference Structural Faults and Repair 2008 CY - Edinburgh, Scotland DA - 2008-06-10 PY - 2008 AN - OPUS4-18065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - Benchmarks for Thickness Measurement of Concrete Elements T2 - SACoMaTiS 2008, International RILEM Conference CY - Varenna, Italy DA - 2008-09-01 PY - 2008 AN - OPUS4-18066 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Thomas, Hans-Martin A1 - Wüstenberg, Hermann T1 - Plattierungsprüfung mittels Ultraschall-Gruppenstrahler und Impulswirbelstrom T2 - DGZfP-Jahrestagung CY - Fulda, Germany DA - 1992-04-27 PY - 1992 AN - OPUS4-18845 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Boehm, Rainer A1 - Wüstenberg, Hermann A1 - Brekow, Gerhard A1 - Thomas, Hans-Martin T1 - Redundant Defect Detection and Evaluation with NDT-Techniques T2 - EPRI, Vessel and Internal Inspection Conference CY - San Antonio, TX, USA DA - 1994-07-11 PY - 1994 AN - OPUS4-18854 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Thomas, Hans-Martin A1 - Fischer, E. T1 - Prüfung der Plattierung von Behältern mit gepulstem Wirbelstrom und Ultraschall T2 - 1. Französisch-Deutsches Seminar "Anwendung von ZfP-Mehrfachprüftechnik zur Verbesserung von Auffindbarkeit und Deutung" CY - Metz, France DA - 1995-10-12 PY - 1995 AN - OPUS4-18858 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Thomas, Hans-Martin A1 - Wüstenberg, Hermann T1 - Inservice Inspection of Pressure Vessels with Special Emphasis on the Surface and Near Surface Areas T2 - EPRI Reactor Pressure Vessels Inspection Conference CY - Olympic Valley, CA, USA DA - 1996-06-04 PY - 1996 AN - OPUS4-18861 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Martin, Tina T1 - Complex Resisitivity (CR) of Wood and Standing Trees T2 - NDTCE 2009 CY - Nantes, France DA - 2009-06-30 PY - 2009 AN - OPUS4-19649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dreßler, Martin T1 - Herstellung von Biokeramik mittels rapid prototyping T2 - Kooperationsforum "Generative Fertigungs-technologien" CY - Berlin, Germany DA - 2009-04-29 PY - 2009 AN - OPUS4-19679 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - Zerstörungsfreie Prüfung von Betonbauteilen mit bildgebenden Ultraschallecho-Verfahren T2 - DGZfP-Arbeitskreis Dresden CY - Dresden, Germany DA - 2010-06-22 PY - 2010 AN - OPUS4-22850 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin T1 - Thickness Measurement and Quality Assurance of Floor Slabs and Diaphragm Walls T2 - Structural Faults & Repair 2010, 13th International Conference and Exhibition, The University of Edinburgh CY - Edinburgh, Scotland DA - 2010-06-15 PY - 2010 AN - OPUS4-22861 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Hans-Martin T1 - Früherkennung von Rollkontakt-Ermüdung (RCF) in Eisenbahnschienen T2 - DGZfP-Dachtagung CY - St. Gallen, Switzerland DA - 2008-04-28 PY - 2008 AN - OPUS4-17704 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Numerische Simulation von Selbstentzündungsvorgängen, Modell und Praxisbeispiele T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Nuremberg, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-17325 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Einflussgrößen auf die Selbstentzündung von Schüttgütern und Stäuben T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Nuremberg, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-17326 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dreßler, Martin T1 - Hochtemperatur Oxidationsschutz von INCONEL-718 T2 - Hannover Messe CY - Hanover, Germany DA - 2008-04-25 PY - 2008 AN - OPUS4-18097 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dreßler, Martin T1 - Keramische Schichten für den Oxidationsschutz T2 - EuroMold 2008 CY - Frankfurt am Main, Germany DA - 2008-12-03 PY - 2008 AN - OPUS4-18099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riedl, Martin T1 - Graffitischutz auf Betonoberflächen T2 - Fachtagung Instandsetzung von Betonbauteilen CY - Rostock, Germany DA - 2008-10-02 PY - 2008 AN - OPUS4-18911 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Pohl, Rainer A1 - Montag, Hans-Joachim A1 - Thomas, Hans-Martin A1 - Wüstenberg, Hermann T1 - NDT techniques for railroad wheel and gauge corner inspection T2 - Railway engineering - 2002, 5th International Conference and Exhibition CY - London, England DA - 2002-07-03 PY - 2002 AN - OPUS4-18892 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin T1 - Atomistic simulation of gas sorption isotherms in a polymer of intrinsic microporosity (PIM-1) T2 - EUROMEMBRANE 2009 Conference CY - Montpellier, France DA - 2009-09-06 PY - 2009 AN - OPUS4-20103 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dreßler, Martin T1 - Generative Fertigungstechniken für die Biokeramik T2 - Tagung des AK Keramikbearbeitung am Institut für Werkzeugmaschinen und Fabrikbetrieb, Fachgebiet Werkzeugmaschinen und Fertigungstechnik der TU Berlin CY - Berlin, Germany DA - 2009-10-01 PY - 2009 AN - OPUS4-20203 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -