TY - JOUR A1 - Lozano-Martín, D. A1 - Martín, M. C. A1 - Chamorro, C. R. A1 - Tuma, Dirk A1 - Segovia, J. J. T1 - Speed of sound for three binary (CH4 + H2) mixtures from p = (0.5 up to 20) MPa at T = (273.16 to 375) K N2 - Speed of sound is one of the thermodynamic properties that can be measured with least uncertainty and is of great interest in developing equations of state. Moreover, accurate models are needed by the H2 industry to design the transport and storage stages of hydrogen blends in the natural gas network. This research aims to provide accurate data for (CH4 + H2) mixtures of nominal (5, 10, and 50) mol-% of hydrogen, in the p = (0.5 up to 20) MPa pressure range and with temperatures T = (273.16, 300, 325, 350, and 375) K. Using an acoustic spherical resonator, speed of sound was determined with an overall relative expanded (k = 2) uncertainty of 220 parts in 10^6 (0.022%). Data were compared to reference equations of state for natural gas-like mixtures, such as AGA8-DC92 and GERG-2008. Average absolute deviations below 0.095% and percentage deviations between 0.029% and up to 0.30%, respectively, were obtained. Additionally, results were fitted to the acoustic virial equation of state and adiabatic coefficients, molar isochoric heat capacities and molar isobaric heat capacities as perfect-gas, together with second and third acoustic virial coefficients were estimated. Density second virial coefficients were also obtained. KW - Speed of sound KW - Acoustic resonator KW - Heat capacity PY - 2020 DO - https://doi.org/10.1016/j.ijhydene.2019.12.012 SN - 0360-3199 VL - 45 IS - 7 SP - 4765 EP - 4783 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-50454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tuma, Dirk A1 - Lozano-Martín, D. A1 - Vega-Maza, D. A1 - Moreau, A. A1 - Martín, M. C. A1 - Segovia, J. J. T1 - Speed of sound data, derived perfect-gas heat capacities, and acoustic virial coefficients of a calibration standard natural gas mixture and a low-calorific H2-enriched mixture N2 - This work aims to address the technical aspects related to the thermodynamic characterization of natural gas mixtures blended with hydrogen for the introduction of alternative energy sources within the Power-to-Gas framework. For that purpose, new experimental speed of sound data are presented in the pressure range between (0.1 up to 13) MPa and at temperatures of (260, 273.16, 300, 325, and 350) K for two mixtures qualified as primary calibration standards: a 11 component synthetic natural gas mixture (11 M), and another low-calorific H2-enriched natural gas mixture with a nominal molar percentage x(H2) = 3 %. Measurements have been gathered using a spherical acoustic resonator with an experimental expanded (k = 2) uncertainty better than 200 parts in 106 (0.02 %) in the speed of sound. The heat capacity ratio as perfect-gas gammapg, the molar heat capacity as perfect-gas Cp,m pg, and the second betaa and third gammaa acoustic virial coefficients are derived from the speed of sound values. All the results are compared with the reference mixture models for natural gas-like mixtures, the AGA8-DC92 EoS and the GERG-2008 EoS, with Special attention to the impact of hydrogen on those properties. Data are found to be mostly consistent within the model uncertainty in the 11 M synthetic mixture as expected, but for the hydrogen-enriched mixture in the limit of the model uncertainty at the highest measuring pressures. KW - Natural gas mixtures KW - Speed-of-sound measurements KW - Equations of state KW - Acoustic virial coefficients PY - 2021 DO - https://doi.org/10.1016/j.jct.2021.106434 SN - 0021-9614 VL - 158 SP - 106434 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-52292 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Martin Tschaikner, Martin A1 - Hohendorf, Stefan A1 - Bellon, Carsten A1 - Haith, M. I. A1 - Huthwaite, P. A1 - Lowe, M. J. S. T1 - Corrosion monitoring with tangential radiography and limited view computed tomography N2 - Accurate and reliable detection of subsea Pipeline corrosion is required in order to verify the integrity of the pipeline. A laboratory trial was conducted with a representative pipe sample. The accurate measurement of the wall thickness and corrosion was performed with high energy X-rays and a digital detector array. A 7.5 MV betatron was used to penetrate a stepped pipe and a welded test pipe of 3 m length and 327 mm outer diameter, with different artificial corrosion areas in the 24 mm thick steel wall. The radiographs were taken with a 40 x 40 cm² digital detector array, which was not large enough to cover the complete pipe diameter after magnification. A C-arm based geometry was tested to evaluate the potential for automated inspection in field. The primary goal was the accurate measurement of wall thickness conforming to the standard. The same geometry was used to explore the ability of a C-arm based scanner in asymmetric mode for computed tomography (CT) measurement, taking projections covering only two thirds of the pipe diameter. The technique was optimized with the modelling Software aRTist. A full volume of the pipe was reconstructed and the CT data set was used for reverse engineering, providing a CAD file for further aRTist simulations to explore the technique for subsea inspections. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.2015 KW - Corrosion monitoring KW - Tangential radiography KW - Computed tomography PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940574 SN - 0094-243X VL - 1706 SP - 110003-1 EP - 110003-8 PB - AIP Publishing AN - OPUS4-37555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Conclusions from the first return campaign of vitrified High-Level Waste on sea going vessels from the competent authority N2 - Germany has to take back vitrified waste from the reprocessing plants in France and Great Britain. The waste resulted from decades of transporting spent fuel for reprocessing to La Hague and Sellafield. The return campaign from France was concluded in 2024 with the transport of five CASTOR® HAW28M casks to the interim storage facility in Philippsburg in southern Germany. The return of waste from Sellafield comprises three campaigns and a total of 20 CASTOR® HAW28M casks. The first campaign was performed in 2020, consisting of six CASTOR® HAW28M casks, while the second campaign was performed in March 2025, consisting of seven CASTOR® HAW28M casks. The casks were transported by rail from Sellafield to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. The third campaign is expected to be performed during 2026. BAM as part of the German competent authority system was among others involved in the assessment of the sea transport. BAM required for the first transport, among others, an assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of the IMDG code and its supplement the INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - PATRAM 2025 CY - San Antonio, Texas, USA DA - 27.07.2025 KW - RAM KW - Transport KW - Radioactive material KW - Sea PY - 2025 SP - 1 EP - 8 PB - INMM CY - Washington D.C. AN - OPUS4-63984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Segovia, J. J. A1 - Tuma, Dirk A1 - Lozano-Martín, D. A1 - Moreau, A. A1 - Martín, M. C. A1 - Vega-Maza, D. T1 - Speed of sound data and acoustic virial coefficients of two binary (N2 + H2) mixtures at temperatures between (260 and 350) K and at pressures between (0.5 and 20) MPa N2 - This work aims to address the technical concerns related to the thermodynamic characterization of gas mixtures blended with hydrogen for the implementation of hydrogen as a new energy vector. For this purpose, new experimental speed of sound measurements have been done in gaseous and supercritical phases of two binary mixtures of nitrogen and hydrogen using the most accurate technique available, i.e., the spherical acoustic resonator, yielding an experimental expanded (k = 2) uncertainty of only 220 parts in 106 (0.022%). The measurements cover the pressure range between (0.5 and 20) MPa, the temperature range between (260 and 350) K, and the composition range with a nominal mole percentage of hydrogen of (5 and 10) mol%, respectively. From the speed of sound data sets, thermophysical properties that are relevant for the characterization of the mixture, namely the second βa and third γa acoustic virial coefficients, are derived. These results are thoroughly compared and discussed with the established reference mixture models valid for mixtures of nitrogen and hydrogen, such as the AGA8-DC92 EoS, the GERG-2008 EoS, and the recently developed adaptation of the GERG-2008 EoS, here denoted GERG-H2_improved EoS. Special attention has been given to the effect of hydrogen concentration on those properties, showing that only the GERG-H2_improved EoS is consistent with the data sets within the experimental uncertainty in most measuring conditions. KW - Speed of sound KW - Acoustic resonance KW - Binary gas mixture PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-551482 DO - https://doi.org/10.1016/j.jct.2022.106791 SN - 0021-9614 VL - 171 SP - 1 EP - 13 PB - Elsevier B. V. CY - Amsterdam AN - OPUS4-55148 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano-Martín, D. A1 - Tuma, Dirk A1 - Vega-Maza, D. A1 - Martín, M. C. A1 - Chamorro, C. R. T1 - Thermodynamic characterization of the (CO2+ O2) binary system for the development of models for CCS processes: Accurate experimental (p, rho, T) data and virial coefficients N2 - Continuing our study on (CO2 + O2) mixtures, this work reports new experimental (p, rho, T) data for two oxygen-rich mixtures with mole fractions x(O2) = (0.50 and 0.75) mol·mol−1, in the temperature range T = (250–375) K and pressure range p = (0.5–20) MPa, using a single-sinker densimeter. Experimental density data were compared to two well-established equation-of-state models: EOS-CG and GERG-2008. In the p, T-range investigated, the EOS-CG gave a better reproduction for the equimolar mixture (x(O2) = 0.5), whereas the GERG-2008 performed significantly better for the oxygen-rich mixture (x(O2) = 0.75). The EOS-CG generally overestimates the density, while the GERG-2008 underestimates it. This complete set of new experimental data, together with previous measurements, is used to calculate the virial coefficients B(T, x) and C(T, x), as well as the second interaction virial coefficient B12(T) for the (CO2+ O2) system. KW - Binary mixtures CO2 + O2 KW - Density measurements KW - Equations of state KW - Virial coefficients PY - 2021 DO - https://doi.org/10.1016/j.supflu.2020.105074 SN - 0896-8446 VL - 169 SP - 5074 PB - Elsevier B. V. CY - Amsterdam AN - OPUS4-51670 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, Hartmut A1 - Munz, Martin A1 - Böhning, Martin T1 - A new method for testing and evaluating the long-time resistance to oxidation of polyolefinic products N2 - A report is presented on the development of a test for determining the long-term oxidation resistance of polyolefin materials, which is accelerated not only by elevated temperatures but also by increased oxygen pressure and a stirred aqueous medium. The method permits durability tests to be carried out at markedly lower temperatures with reasonable testing durations and significantly reduced diffusion limited oxidation effects and allows for physical and chemical impacts of aqueous media. Oxidative durability can be assessed by autoclave immersion exposures at three different temperatures (60, 70 and 80 degrees C) and 50 bar oxygen pressure and at 80 degrees C and two different oxygen pressures (usually 10 and 20 bar). Accelerated test data are evaluated by modified Arrhenius equations with the application of a three-dimensional regression analysis. The application of the test method to various materials, including PP non-woven materials and geosynthetics is demonstrated. 10 refs. KW - Polyolefin KW - Testing KW - Oxidation KW - Durability KW - Geosynthetics PY - 2008 SN - 0967-3911 SN - 1478-2391 VL - 16 IS - 1 SP - 71 EP - 79 PB - RAPRA Technology Ltd. CY - Shrewsbury AN - OPUS4-17187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Transport of HLW canisters on sea vessels N2 - Germany had been transporting spent fuel to the reprocessing plant in Sellafield and La Hague for decades until around 2005. Resulting from the obligation to take back the vitrified high-level waste from reprocessing six CASTOR® HAW28M filled with 168 canisters with radioactive waste in vitrified form were transported from Sellafield to the interim storage facility Biblis in 2020. Rail wagons were used for the transport to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. BAM was involved in the authority assessment of the conditions for the sea transport. For the first transport BAM required among others, assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask in order to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of IMDG code and its supplement INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - RAMTrans 2024 CY - London, United Kingdom DA - 14.05.2024 KW - Transport KW - Spent nuclear fuel KW - Ship KW - Sea KW - High level waste PY - 2024 SP - 1 EP - 8 AN - OPUS4-60092 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feigl, Michael A1 - Nofz, Marianne A1 - Sojref, Regine A1 - Dressler, Martin A1 - Pulz, Robert A1 - Rehmer, Birgit A1 - Feldmann, Ines A1 - Sabel, Martin T1 - Aluminiumoxidschichten für den Oxidationsschutz von Hochtemperaturlegierungen N2 - Effektive Al2O3-Keramik-Schutzschichten könnten die Verwendung preiswerterer Legierungen für Hochtemperaturanwendungen ermöglichen. Die Anforderungen an diese Schichten sind eine gute Haftung, chemische Stabilität und Dichtheit gegen die Umgebungsatmosphäre. T2 - DKG-Jahrestagung/Symposium Hochleistungskeramik CY - Aachen, Germany DA - 23.03.2009 KW - Schichtherstellung KW - Schichttestung KW - Hochtemperaturanwendungen PY - 2009 AN - OPUS4-35836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dreßler, Martin A1 - Dombrowski, Felix A1 - Simon, Ulla A1 - Börnstein, Julian A1 - Hodoroaba, Vasile-Dan A1 - Feigl, Michael A1 - Grunow, Sabrina A1 - Gildenhaar, Renate A1 - Neumann, Martin T1 - Influence of gelatine coatings on compressive strength of porous hydroxyapatite ceramics N2 - Porous ceramics prepared by the foam replication technique have a high porosity and low mechanical stability. It has been reported that coating such porous ceramics with gelatin allows for an improved compressive strength. Little details regarding the influence of important gelatin parameters such as concentration, temperature and drying conditions as well as bloom number which is a measure of the gel rigidity, on this toughening effect are available. This paper investigates the influence of these parameters on compressive strength of gelatin coated porous hydroxyapatite ceramics. It was found that concentration in the gelatin sols has a marked impact whereas sol temperature, bloom number and differing conditions during subsequent drying have only little influence on the compressive strength of the coated ceramics. KW - Films KW - Composites KW - Strength KW - Apatite KW - Biomedical application PY - 2011 DO - https://doi.org/10.1016/j.jeurceramsoc.2010.11.004 SN - 0955-2219 SN - 1873-619X VL - 31 IS - 4 SP - 523 EP - 529 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-23216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kang, Chongjie A1 - Arcones, Daniel Andrés A1 - Becks, Henrik A1 - Beetz, Jakob A1 - Blankenbach, Jörg A1 - Claßen, Martin A1 - Degener, Sebastian A1 - Eisermann, Cedric A1 - Göbels, Anne A1 - Hegger, Josef A1 - Hermann, Ralf A1 - Kähler, Philipp A1 - Peralta, Patricia A1 - Petryna, Yuri A1 - Schnellenbach‐Held, Martina A1 - Schulz, Oliver A1 - Smarsly, Kay A1 - Fatih Sönmez, Mehmet A1 - Sprenger, Bjarne A1 - Unger, Jörg F. A1 - Vassilev, Hristo A1 - Weiser, Martin A1 - Marx, Steffen T1 - Intelligente digitale Methoden zur Verlängerung der Nutzungsdauer der Nibelungenbrücke N2 - Um die Lebensdauer von Bauwerken unter Wahrung derer Standsicherheit und Funktionsfähigkeit zu verlängern, bedarf es effektiver Monitorings‐ sowie Instandhaltungskonzepte. Im Rahmen des von der Deutschen Forschungsgemeinschaft (DFG) geförderten Schwerpunktprogramms 2388 „Hundert plus – Verlängerung der Lebensdauer komplexer Baustrukturen durch intelligente Digitalisierung“ (kurz: SPP 100+) werden hierfür innovative, interdisziplinäre Methoden entwickelt und an der Nibelungenbrücke in Worms (NBW) validiert. Der vorliegende Beitrag stellt einige dieser neuentwickelten digitalen Methoden vor. Unter anderem umfasst dies zwei Systeme des Structural Health Monitoring (SHM) und deren zielorientierte Verknüpfung von mehreren Beschleunigungsmessdaten zur umfassenden Zustandsbewertung. Ergänzend werden innovative datenbasierte Simulationsmethoden zur Bestimmung des Temperaturfelds des Brückenüberbaus vorgestellt sowie mehrere Finite‐Elemente‐Modelle unterschiedlicher Detailtiefe präsentiert und miteinander verglichen. Abschließend werden innovative Methoden zum Verwalten des Bestandswissens von Brückenbauwerken diskutiert. Die Methoden wurden überwiegend unabhängig voneinander entwickelt und an der NBW validiert. Im nächsten Schritt werden die Methoden integriert, um die Instandhaltung der NBW zu unterstützen. KW - Nibelungenbrücke Worms KW - Digitaler Zwilling KW - Prädiktive Instandhaltung KW - Bauwerksmonitoring KW - Nachrechnung KW - Verkehrsinfrastruktur KW - FE-Modell PY - 2025 DO - https://doi.org/10.1002/best.70070 SN - 0005-9900 VL - 121. Jahrgang 2026 SP - 1 EP - 18 PB - Ernst & Sohn a Wiley Brand CY - Wien, Austria AN - OPUS4-65288 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Martin A1 - Wu, Dejian A1 - Zhao, P. A1 - Tan, X. A1 - Huang, W. A1 - Qianc, X. T1 - Minimum explosion concentrations of coal dusts with CH4/H2/CO below the gas lower explosion limit N2 - A 20-L spherical explosion chamber was used to investigate the explosion characteristics of dust clouds in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). including minimum explosion concentration (MEC) of dust. Explosion pressure (Pex) and explosion pressure rise (dp/dt)ex). Two dust samples (anthracite coal, bituminous coal) and were three flammable gases (CH4, H2 and CO) were tested. Experimental results showed that the explosion of hybrid mixtures occurs when both dust and gas concentrations are lower than the LEL/MEC of the single substances. Meanwhile. all flammable gases with different volume fractions have distinct effects on the MEC. Pex and (dp/dt)ex of the dust samples. With the increase of the flammable gas concentration. either the Pex and (dp/dt)ex increase or the MEC decreases for all the hybrid mixtures of both two dust samples. At the same concentration of coal dusts. the addition of CH4 promotes higher explosion risks than the other two flammable gases. The distribution of (dp/dt)ex is quite different with the restricted area defined by empirical formulas. These results improve our understanding of the explosion behaviour and the explosion risk of hybrid dust-gas mixtures in air. KW - Dust explosions KW - Gas explosions KW - Minimum explosible concentration KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116401 SN - 0032-5910 VL - 260 SP - UNSP 116401 PB - Elsevier Sci. Ltd. AN - OPUS4-49956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Schmidt, Martin A1 - Tan, X. A1 - Zhao, P. A1 - Huang, W. A1 - Qian, X. T1 - Minimum ignition temperature of carbonaceous dust clouds in air with CH4/H-2/CO below the gas lower explosion limit N2 - Godbert-Greenwald furnace was used to investigate the minimum ignition temperature of dust clouds (MITC) in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). Three flammable gases (CH4, H2 and CO) and three carbonaceous dusts (anthracite coal, bituminous coal and sweet potato starch) were tested. Results showed that all flammable gases have distinct effects on the MITC of the dust samples and volatile matter content of dust plays an important role during the ignition process. Specifically, the MITC of anthracite coal dust decreased from 610 °C to 560 °C, 580 °C and 570 °C with 3% CH4, 3% CO and 2.5% H2, respectively. Moreover, a heterogeneous ignition mechanism model was proposed to verify the equally global ignition characteristic between hybrid anthracite coal-CxHy mixture and bituminous coal. All three gases had an ignorable effect on the MITC of starch dust considering the experimental error. The presence of CO and H2 slightly promoted the ignition of bituminous coal dust, but the addition of CH4 showed a distinct concentration effect on the MITC of bituminous coal: the MITC decreased with 1% CH4 while increased with 2% and 3% CH4. This negative-effect of flammable gases at such low concentrations on ignition temperature of bituminous coal dusts was found for the first time. Furthermore, the presence of the 2nd flammable gas had a smaller effect on the MITC of dust samples with a higher volatile content, resulted from the competition of heterogeneous and homogeneous ignition mechanisms. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116811 SN - 0016-2361 VL - 264 SP - 116811 PB - Elsevier Ltd. AN - OPUS4-50856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Günther, Martin T1 - Flame retardancy of polyurethanes N2 - Polyurethanes (PU) represent one of the most versatile classes of plastics. They are processed and used as thermoplastic, elastomer, and thermoset. The requirements regarding flammability are correspondingly versatile. Depending on the material and the field of application, specific fire tests have to be fulfilled. This paper describes the different concepts used to fulfil these requirements by choosing the right raw materials and flame retardants. KW - Polyurethane KW - Flame retardant KW - Foam KW - Flammability KW - Pyrolysis KW - Cone calorimeter PY - 2020 VL - 17 IS - 1 SP - 44 EP - 48 PB - Dr. Gupta AN - OPUS4-50737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Günther, Martin T1 - Flammschutz von Polyurethanen N2 - Polyurethane (PU) bilden eine der vielseitigsten Klassen der Polymerwerkstoffe. Kein anderer Kunststoff wird sowohl als Thermoplast, als Elastomer wie auch als Duroplast verarbeitet und eingesetzt. Entsprechend vielfältig sind auch die Anforderungen an den Flammschutz. Je nach Material und Anwendung müssen spezifische Brandnormen erfüllt werden. Der vorliegende Aufsatz gibt einen Überblick über die verfügbaren Ansätze, um durch geeignete Auswahl der Rohstoffe und der Flammschutzmittel diese verschiedensten Anforderungen an das Brandverhalten zu erfüllen. KW - Polyurethan KW - Flammschutz KW - Pyrolyse KW - Schaum KW - Cone calorimeter PY - 2020 VL - 20 IS - 1 SP - 48 EP - 53 PB - Dr. Gupta AN - OPUS4-50736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martin, Tina A1 - Nordsiek, S. A1 - Weller, Andreas T1 - Low-frequency impedance spectroscopy of wood N2 - The method of low-frequency impedance spectroscopy has been successfully applied in Earth sciences to characterize soils and rocks. The method uses the diagnosing power of complex electrical resistivity in a frequency range between 1 mHz and 1 kHz. In our study, the potential of this method has been explored for the investigation of wood. We observed remarkable differences in the resulting spectra of complex resistivity for different European and Tropical tree species. The data processing of the acquired low-frequency impedance spectra yields integrating parameters. The comparison of the integrating parameters with the mean pore diameter that has been separately determined for the tropical tree species indicates clear correlations. An additional investigation has revealed remarkable difference in the complex resistivity spectra between oil bearing and non-oil bearing sandal wood. This result and the relations between electrical parameters and structural parameters of wood indicate the prospective potential of low-frequency impedance spectroscopy. KW - Holz KW - Spektroskopie KW - ZfP KW - SIP KW - Nondestructive KW - Low-frequency impedance spectroscopy KW - Spectral induced polarization PY - 2015 DO - https://doi.org/10.5171/2015.910447 SP - 1 EP - 9 PB - IBIMA Publ. AN - OPUS4-34811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Der Einfluss des Staubungsverhaltens auf druckentlastete Staubexplosionen T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen DA - 2015-11-05 PY - 2015 AN - OPUS4-34789 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Liebner, Christian A1 - Spoormaker, T. T1 - Identifizierung von sicherheitstechnisch gefährlichen Bedingungen für schlagartige Kompressionsvorgänge chemisch instabiler Gase im industriellen Maßstab N2 - Tetrafluorethen wird von der Polymerindustrie seit Jahrzenten als monomeres Ausgangsmaterial sowohl für die Herstellung von Polymeren (PTFE) als auch für Kopolymere (PCTFE) eingesetzt. Aufgrund seiner Eigenschaft als chemisch instabiles Gas kann TFE auch ohne Luftsauerstoff oder einen anderen Oxydator explosionsartig zerfallen. Nach der Initiierung des Zerfalls kann dieser unter bestimmten Bedingungen aufgrund des exothermen Reaktionsverhaltens sich selbstständig in Apparaten und Rohrleitungen ausbreiten. Dies geht aufgrund der freigesetzten Reaktionsenthalpie mit einem schlagartigen Anstieg von Druck und Temperatur einher, was zu erheblichen Belastungen der Materialien bis hin zum Versagen und Bruch und möglichen Folgeschäden einschließlich Personenschäden führen kann und in der Vergangenheit bereits mehrfach geführt hat. Besonders nach Wartungsarbeiten besteht die Gefahr, dass Teilabschnitte im Rohrleitungssystem mit TFE, Stickstoff oder Luft gefüllt sind mit Drücken in einem Bereich zwischen technischem Vakuum und atmosphärischem Druck wohingegen angrenzende Rohrabschnitte oder Behälter immer noch TFE bei Betriebsdrücken bis 32 bar enthalten können. Dabei sind die Abschnitte in der Praxis häufig durch Kugelhähne voneinander getrennt, die aufgrund ihrer Öffnungscharakteristik bereits bei geringen Betätigungswinkeln eine große Querschnittsfreigabe für die Strömung im Rohr ermöglichen. Dadurch können schlagartige Kompressionsvorgänge des Gases im Niederdruckbereich ermöglicht werden, die allein aufgrund der thermodynamischen Zustandsänderung zu einer erheblichen Temperaturerhöhung führen und im schlimmsten Fall zur Initiierung der Zerfallsreaktion führen können. Es wird erstmalig ein Versuchsaufbau im Industriemaßstab, der einer explosionsartigen Zerfallsreaktion von TFE standhalten kann. Zahlreiche Sicherheitskonzepte einschließlich diverser Berstscheibenkonfigurationen als auch zeitgesteuerte Schnellschlussventile wurden eingehend untersucht und bewertet, um die optimale Versuchskonfiguration für bestmögliche Reproduzierbarkeit festzulegen. Es fand eine systematische Untersuchung der schlagartigen Kompression der Systeme Luft/Luft, TFE/Luft, TFE/TFE und TFE/N2 statt. In der Hochdrucksektion wurden Drücke bis 30 bar realisiert und im Niederdrucksektor konnten Anfangsdrücke im Bereich weniger Millibar bis hin zu Atmosphärendruck eingestellt werden. Als Hauptergebnis wurde ein „Hazard diagram" erstellt, mit dessen Hilfe die Zündwahrscheinlichkeit in Abhängigkeit vom Hochdruck und Niederdruck abgeschätzt werden kann. Gefährliche Bedingungen in Rohrleitungen können dadurch auf einfachem Weg identifiziert werden. Als Referenzsystem zur Beurteilung der maximal erreichbaren nicht reaktiven Kompressionstemperaturen wurde Luft/Luft verwendet. Die damit ermittelten Daten dienten zur Bewertung von zusätzlichen exothermen Effekten, wie sie etwa bei Vorreaktion des TFE im Falle einer Dimerisierung auftreten können. Entgegen der ursprünglichen Annahme konnten die Systeme TFE/Stickstoff und TFE/TFE im verwendeten Aufbau nicht durch Kompressionsvorgänge gezündet werden. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Tetrafluoroethen KW - Zerfall KW - Selbstentzündung KW - Adiabate Kompression PY - 2015 SN - 978-3-86011-091-1 SP - 1 EP - 10 AN - OPUS4-34852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten N2 - Bei elektrochemischen Untersuchungen von atmosphärischen Korrosionsreaktionen an deckschicht- und passivschichtbildenden Werkstoffen stößt man elektrolytseitig an Grenzen. So erweisen sich sowohl das Nachempfinden eines dünnen Feuchtfilms als auch die Interpretation von elektrochemischen Messungen in so genannten Bulk-Lösungen (eine „Masse“ an Elektrolyt) hinsichtlich des Korrosionsverhaltens unter atmosphärischen Bedingungen häufig als schwierig. Eine neue Herangehensweise an diese Problemstellung in der Korrosionsforschung beinhaltet den Einsatz von gelartigen Elektrolyten als Alternative zu den Bulk-Elektrolyten. Gelartige Elektrolyte bilden einen dünnen Feuchtfilm auf der Werkstoffoberfläche aus, wodurch die natürlich gebildete Deckschicht ähnlich wie an Atmosphäre beeinflusst wird und nahezu zerstörungsfrei untersucht werden kann. Durch eine elektrochemische Instrumentierung können geeignete Kennwerte wie Polarisationswiderstände und Korrosionsströme ermittelt werden, die Aussagen zur Kinetik der Deckschichtbildung und zur Stabilität der gebildeten Deckschichten unter Einwirkung eines dünnen Feuchtfilms ermöglichen. Anhand von auf Polysaccharid basierenden Gelpads werden im Vortrag verschiedene Zinkschichtsysteme und Aluminiumlegierungen untersucht, die natürlich gebildeten Deckschichten elektrochemisch charakterisiert und korrosionsrelevante Kennwerte bestimmt. Die ermittelten Kennwerte erlauben eine Differenzierung verschiedener Schichtsysteme und beschreiben die momentane Schutzwirkung der Deckschichten unter atmosphärischen Bedingungen. T2 - 18. Werkstofftechnisches Kolloquium der TU Chemnitz CY - Chemnitz, Germany DA - 10.03.2016 KW - gelartige Elektrolyte KW - Verzinkungen KW - Korrosionsuntersuchungen KW - gel-type electrolytes KW - zinc coatings KW - corrosion investigations PY - 2016 AN - OPUS4-35552 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - The KorroPad - A novel test method for assessing the pitting corrosion susceptibility of stainless steel surfaces N2 - Pitting corrosion is one of the most common mechanisms of local passivity breakdown on stainless steels. Electrochemical methods have preferentially been applied for the evaluation of pitting corrosion resistance of stainless steels in laboratory. Nevertheless, some of them are not reliable enough and in general the application of electrochemical methods in the field becomes difficult because of a required deep understanding of corrosion phenomena and measurement technology. A new approach for the evaluation of the pitting corrosion susceptibility of stainless Steel surfaces in the laboratory as well as in the field is frequently demanded by representatives of the metalworking industry. Therefore, the KorroPad-test was invented and patented as part of a research project at the BAM Federal Institute for Materials Research and Testing in Germany. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - KorroPad KW - Pitting corrosion KW - Stainless steel PY - 2015 SP - Paper 5_730, 1 AN - OPUS4-34297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Martin-Sanchez, Pedro Maria T1 - Quantitative PCR Assays for Monitoring Microorganisms Associated with Biodeterioration Cases T2 - XXV Spanish Microbiology Society Congress CY - Logrono, Spain DA - 2015-07-06 PY - 2015 AN - OPUS4-34255 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Reinemann, S. T1 - Electrochemical investigations regarding the influence of deformation-induced martensite on the corrosion behaviour of austenitic stainless steels N2 - Contents of deformation-induced martensite in the lattice structure of austenitic stainless steels lead to an either beneficial or detrimental change of mechanical and magnetic properties depending on the prospective application. Whereas these changes are well-known and investigated widely the influence of deformation-induced martensite on the corrosion behaviour is frequently an issue of scientific discussions. There are opposing opinions that depend on the type of corrosion mechanism being investigated for example regarding pitting corrosion resistance in Chloride containing media. In it is stated that pitting resistance is not influenced by deformationinduced martensite while in it is discussed that more pitting occurs on martensitic structure. The same conflictive opinions appear regarding active dissolution in acidic media or intergranular corrosion. In addition, when having deeper insight into literature it can be concluded that even the type of test method, i. e. dynamic or static testing, has a big influence on the obtained results concerning the influence of martensite in austenitic stainless steels. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - Deformation-induced martensite KW - Stainless steel KW - Electrochemical investigations PY - 2015 SP - paper 5_776 AN - OPUS4-34617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Heyn, A. ED - Lampke, T. ED - Wagner, G. ED - Wagner, M.F.-X. T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten N2 - Bei elektrochemischen Untersuchungen von atmosphärischen Korrosionsreaktionen an deckschicht- und passivschichtbildenden Werkstoffen stößt man elektrolytseitig an Grenzen. So erweisen sich sowohl das Nachempfinden eines dünnen Feuchtfilms als auch die Interpretation von elektrochemischen Messungen in so genannten Bulk-Lösungen (eine „Masse“ an Elektrolyt) hinsichtlich des Korrosionsverhaltens unter atmosphärischen Bedingungen häufig als schwierig. Eine neue Herangehensweise an diese Problemstellung in der Korrosionsforschung beinhaltet den Einsatz von gelartigen Elektrolyten als Alternative zu den Bulk-Elektrolyten. Gelartige Elektrolyte bilden einen dünnen Feuchtfilm auf der Werkstoffoberfläche aus, wodurch die natürlich gebildete Deckschicht ähnlich wie an Atmosphäre beeinflusst wird und nahezu zerstörungsfrei untersucht werden kann. Durch eine elektrochemische Instrumentierung können geeignete Kennwerte wie Polarisationswiderstände und Korrosionsströme ermittelt werden, die Aussagen zur Kinetik der Deckschichtbildung und zur Stabilität der gebildeten Deckschichten unter Einwirkung eines dünnen Feuchtfilms ermöglichen. Anhand von auf Polysaccharid basierenden Gelpads werden im vorliegenden Beitrag verschiedene Zinkschichtsysteme und Aluminiumlegierungen untersucht, die natürlich gebildeten Deckschichten elektrochemisch charakterisiert und korrosionsrelevante Kennwerte bestimmt. Die ermittelten Kennwerte erlauben eine Differenzierung verschiedener Schichtsysteme und beschreiben die momentane Schutzwirkung der Deckschichten unter atmosphärischen Bedingungen. T2 - 18. Werkstofftechnisches Kolloquium der TU Chemnitz CY - Chemnitz, Germany DA - 10.03.2016 KW - Korrosionsuntersuchungen KW - Corrosion investigations KW - Verzinkungen KW - Zing coatings KW - gelartige Elektrolyte KW - Gel-type electrolytes PY - 2016 SN - 978-3-00-052212-3 SN - 1439-1597 VL - 59 SP - 313 EP - 323 PB - TU Chemnitz, Fakultät für Maschinenbau, Institut für Werkstoffwissenschaft und Werkstofftechnik CY - Chemnitz AN - OPUS4-35637 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschaikner, Martin T1 - Laminographic inspection of large fibre composite structures at the production site N2 - Short describtion of the technology and results of laminography. T2 - 7th International Symposium on NDT in Aerospace CY - Bremen, Germany DA - 16.11.2015 KW - Laminography KW - 3D Reconstruction KW - Inspection of CFRP KW - Laminografie KW - 3D Rekonstruktion KW - Untersuchung von CFK PY - 2015 AN - OPUS4-35610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klippel, Alexander A1 - Schmidt, Martin A1 - Mücke, Olaf A1 - Krause, U. T1 - Dust concentration measurements during filling of a silo and CFD modeling of filling processes regarding exceeding the lower explosion limit N2 - Measurement and numerical simulation of local dust concentrations over time in a vessel can only be done with some uncertainty due to the complexity of the behavior of dust/air mixtures. Dust concentration was measured in a 50 m³ vessel and compared to simulations with a commercial CFD code. A 50 m³ silo was used with two different filling methods. In one setup dust was conveyed with pneumatic filling at the top. The other filling was done with pressurized air and a homogenous injection via eight nozzles. Experiments were repeated three to four times with two kinds of dusts and the results were used to evaluate reproducibility of dust concentration measurements over time in a vessel depending on the filling method. Dust concentrations over time varied up to 30% from the average for homogenous injection and even more for pneumatic filling. Numerical investigations were done with maize starch. Measured concentrations were compared to simulated ones with the commercial CFD code ANSYS CFX R14 using an Euler/Lagrange approach. Drag force, turbulent dispersion force, particle size distribution, particle surface area and particle/particle interaction were modeled. A general agreement of measurement and simulation was achieved. Numerical simulations of filling processes were used to predict parts of the vessel where the lower explosion limit is reached and exceeded. This could help to improve dust explosion protection, if it is used to find configurations where the dust concentration exceeds the lower explosion limit only in small parts of the vessel during filling, e.g. using different injection points or injection angles. The volume where LEL is reached or exceeded in a 50 m³ silo is shown for pneumatic and homogenous filling. Volume of combustible atmosphere in the vessel over time is compared for two pneumatic filling configurations and one worst-case homogenous injection configuration. KW - CFD KW - Euler/Lagrange approach KW - Dust explosion protection KW - Dust concentration measurement KW - Dust explosion KW - Dustiness KW - Dispersion KW - Venting PY - 2014 DO - https://doi.org/10.1016/j.jlp.2014.02.006 SN - 0950-4230 SN - 1873-3352 VL - 29 SP - 122 EP - 137 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-30330 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aurich, Dietmar A1 - Martin, Erich T1 - Werkstoffe, Baustoffe einschließlich Prüfverfahren und Prüfeinrichtungen - Metallische Werkstoffe PY - 1964 SN - 0372-543X VL - 106 IS - 27 SP - 1365 EP - 1372 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-30148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böhning, Martin A1 - Niebergall, Ute A1 - Adam, Adeline A1 - Stark, Wolfgang T1 - Impact of biodiesel sorption on mechanical properties of polyethylene N2 - The time-dependent sorption of biodiesel in a typical polyethylene for container applications is investigated in comparison to conventional diesel fuel at three different temperatures. In this context, the desorption behavior is also addressed. Subsequently, the effects of both penetrants on mechanical properties are characterized in terms of impact strength and dynamic-mechanical analysis. The discussion of property changes is firstly based on the sorption kinetics of biodiesel and diesel, which is determined by immersion experiments allowing for the calculation of respective diffusion coefficients. Changes in impact strength as determined by the Charpy method are further characterised in more detail by analyzing the fracture surfaces, and correlated with results of dynamic-mechanical analysis. KW - Biodiesel KW - Fuel sorption KW - Desorption KW - Impact strength KW - Dynamic-mechanical analysis KW - PE-HD PY - 2014 DO - https://doi.org/10.1016/j.polymertesting.2013.12.003 SN - 0142-9418 VL - 34 SP - 17 EP - 24 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-30096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Fettig, Ina A1 - Seeger, Stefan A1 - Werrel, Martin A1 - Deubel, Jan A1 - Raspe, Tina A1 - Piechotta, Christian A1 - Krüger, Simone T1 - Raumbrände - Teil 2: Versuchsaufbau und Brandspurenanalytik N2 - Der vorliegende Bericht ist der 2.Teil eines Gesamtberichtes und schildert ausführlich die im Kontext des BAM-Innovationsoffensive-Projektes „Chemische Brandspurenanalytik“ durchgeführten Untersuchungen und fasst die gewonnenen analytischen Erkenntnisse zusammen. Der gesamte Bericht gliedert sich in drei Teile. Der erste Teil beinhaltet den Aufbau, die Durchführung und die brandtechnologische Auswertung der durchgeführten Raumbrandversuche, während in dem hier vorliegenden Teil die analytischen Methoden zum Nachweis des Brandbeschleunigers in den Brandrückständen vorgestellt und ausgewertet werden. Die Beurteilung von Brandspuren und daraus abgeleitet die Rekonstruktion eines Brandverlaufes beruhen auch auf der präzisen chemischen Analyse der Brandprodukte. Im Rahmen dieses Projektes wurde eine innovative Methodik entwickelt, wie verfügbare Analysetechniken in geeigneter Weise kombiniert werden können, um aus festen, flüssigen und gasförmigen Brandrückständen Rückschlüsse auf den Brandverlauf ziehen zu können. Neben der Untersuchung von Proben von realen Brandorten wurden verschiedene wohnungstypische Materialien unter Laborbedingungen unterschiedlichen Brandszenarien unterworfen. Die dabei entstehenden Brandgase, Aerosole sowie der verbleibende Brandrückstand wurden durch geeignete analytische Verfahren analysiert, um mögliche Brandursachen beurteilen zu können. Der Schwerpunkt dieses Berichtes liegt in dem Nachweis von Brandbeschleunigern. Es zeigte sich, dass mittels der Kombination aus HS-SPME-GC-MS sowohl in den festen Brandrückständen, als auch in den Kondensaten Brandbeschleuniger eindeutig und verlässlich nachgewiesen werden können. Anhand von 5 verschiedenen Zimmerbrandversuchen wurde der Einfluss von Brandbeschleunigern auf den Brandverlauf experimentell untersucht. Es wurden verschiedene brandtechnologische Kennwerte, wie der Massenverlust des gesamten Brandraums, Brandraumtemperaturen, die Wärmefreisetzungen sowie die Rauchgasemissionen ermittelt und beurteilt. Die Rauchgasanalyse erfolgte im Schlot, im Brandraum sowie in der Brandraumöffnung mittels Fourier Transformierte Infrarot-FTIR-Spektroskopie. Neben diesen brandtechnologischen Untersuchungen, die im Bericht Teil 1 enthalten sind, erfolgten auch chemisch-analytische Untersuchungen nach dem Brand, mit dem Ziel, den eingesetzten Brandbeschleuniger nachzuweisen. Im Anschluss an die jeweiligen Zimmerbrandversuche wurden verschiedene Brandrückstandsproben aus dem Brandschutt, Wischproben von den Wänden und den übriggebliebenen Gegenständen genommen und mit Hilfe einer entwickelten HS-SPME-GC-MS-Methode (Headspace-Solid Phase Micro Extraction-Gas Chromatographie-Massenspekrometrie) in Hinblick eines möglichen Brandbeschleunigernachweis analysiert. KW - Raumbrände KW - Rauchgase KW - Wärmefreisetzung KW - Rauchgastemperaturen KW - Analytik PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-301257 SN - 978-3-9815944-8-5 SP - 1 EP - 190 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-30125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert A1 - Kind, Thomas A1 - Krause, Martin A1 - Schulze, S. A1 - Taffe, A. A1 - Trela, Christiane A1 - Wöstmann, Jens T1 - Praktische Anwendung zerstörungsfreier Prüfverfahren an Brücken N2 - Die drei Beispiele zerstörungsfreier Prüfungen an Spannbetonbrücken zeigen unterschiedliche Problemstellungen und deren Lösung mit unterschiedlichen Ansätzen. Allen drei Beispielen gemeinsam ist die Verwendung kommerzieller Geräte. Diese werden von verschiedenen Anbietern bereitgestellt. Eine weitere Gemeinsamkeit ist, dass die Grundgeräte durch zusätzliche Maßnahmen ergänzt. Erst dann ist der gewünschte Untersuchungserfolg sicher gestellt. Im ersten Beispiel wurde die vom Auftraggeber geforderte Präzision dadurch erreicht, dass systematische Voruntersuchungen stattfanden. Die Übertragung der Lokalisierung direkt auf die Betonoberfläche stellte sicher, dass keinen Informationsverluste an die nachfolgenden Aufgaben auftraten. Das zweite Beispiel zeigt den Nutzen von Automatisierung und Kombination von Verfahren. Damit können dem Auftraggeber die notwendigen Angaben über Einbauteile mit großer Detaitreue und leicht verständlicher Visualisierung aufbereitet werden. Der abschließende Bericht zeigt, wie vorhandene Auswertungen sinnvoll durch noch in der Forschung befindliche Ansätze bereichert werden. Insgesamt ist die zerstörungsfreie Prüfung in der Lage, an Brücken preisrelevante Fragestellungen zu lösen. Voraussetzung hierfür ist eine sorgfältig geplante Vorgehensweise und ein sicheres Verständnis der Grundlage der eingesetzten Geräte und Auswertungsschritte. T2 - 1. Brückenkolloquium - Beurteilung, Ertüchtigung und Instandsetzung von Brücken CY - Ostfildern/Stuttgart, Germany DA - 24.06.2014 PY - 2014 SP - Paper 00_08, 1 EP - 8 AN - OPUS4-31032 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hattwig, Martin ED - Ziegler, Kurt ED - Becker, Gerhard Wilhelm T1 - Messung der Rückstoßkraft bei der Explosionsdruckentlastung T2 - Grundsätze der Chemischen Sicherheitstechnik und ihre Anwendung in der Praxis CY - Berlin, Germany DA - 08.10.1981 PY - 1982 SP - 91 EP - 92 CY - Berlin AN - OPUS4-36222 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hattwig, Martin ED - Ziegler, Kurt ED - Becker, Gerhard Wilhelm T1 - Sicherheitstechnische Probleme bei Detonationen von Gasen T2 - Grundsätze der Chemischen Sicherheitstechnik und ihre Anwendung in der Praxis CY - Berlin, Germany DA - 08.10.1981 PY - 1982 SP - 103 EP - 104 CY - Berlin AN - OPUS4-36224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hattwig, Martin T1 - Der Schutz gegen Staubexplosionen und Staubbrände bei der Vermahlung und Lagerung von Produkten aus tierischen Abfällen PY - 1982 SN - 1437-949X VL - 34 IS - 1 SP - 9 EP - 16 PB - Wirtschaftsdienst d. Fleischmehlindustrie CY - Bonn AN - OPUS4-36226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hattwig, Martin T1 - Entstehung und Auswirkungen von Raumexplosionen PY - 1982 SN - 0340-7551 VL - 12 IS - 4 SP - 357 EP - 365 CY - Berlin AN - OPUS4-36227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hattwig, Martin A1 - Wandrey, Peter-Andreas ED - Ziegler, Kurt ED - Becker, Gerhard Wilhelm T1 - Sicherheit bei der Herstellung und beim Transport oxidierend wirkender Stoffe und organischer Per-Verbindungen T2 - Grundsätze der Chemischen Sicherheitstechnik und ihre Anwendung in der Praxis CY - Berlin, Germany DA - 08.10.1981 PY - 1982 SP - 61 EP - 70 CY - Berlin AN - OPUS4-36229 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Dörfel, Ilona A1 - Steinborn, Gabriele A1 - Langner, Jeanette A1 - Krietsch, Arne A1 - Seeger, Stefan A1 - Österle, Werner A1 - Schmidt, Martin A1 - Bresch, Harald T1 - Dossier on titanium dioxide - Part 1/1 - NM 105 N2 - In November 2007, OECD’s Working Party on Manufactured Nanomaterials (WPMN) launched the Sponsorship Programme for the Testing of Manufactured Nanomaterials (hereafter the Testing Programme). The objective was to conduct specific tests, relevant to human health and environmental safety endpoints, on a variety of manufactured nanomaterials (MN). The outcomes of the Testing Programme were intended to assess the applicability of the existing test guidelines1 to nanomaterials, as well as to provide useful information on any intrinsic properties of MNs, which are different from the same bulk material with greater external dimensions. Understanding the properties of NMs is crucial to choose appropriate strategies for hazard identification, risk assessment or risk management measures. The Testing Programme involved delegations from OECD member countries, some non-member economies and other stakeholders. The broad international representation, from a range of delegations enabled the programme to pool expertise and resources without which this programme would not have been possible. KW - Nanomaterial KW - Nanoparticle KW - Sponsorship programme KW - Nano characterization PY - 2015 UR - http://www.oecd.org/env/ehs/nanosafety/dossier-on-silver-nanoparticles-part1-1.htm IS - 54 SP - 27 CY - Paris AN - OPUS4-35430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Wille, Frank A1 - Nehrig, Marko A1 - Feldkamp, Martin ED - Sorenson, K.B. T1 - Thermal performance of transportation packages for radioactive materials N2 - Prevention of damage caused by heat is one of the objectives during package safety evaluation. This chapter describes basics of heat transfer and major aspects of regulatory requirements. Package temperature criteria and fire test conditions are explained. Special package design features regarding material properties and safety evaluation concepts are discussed. Experimental fire testing is performed by pool fire or with the help of a furnace. Analysis by numerical or analytical approaches show temperature gradients and whether compliance with the regulatory requirements and specified design temperatures is met. The tightness of the package lid system influenced by geometry changes is in the focus of a holistic thermo-mechanical approach considering the entire mechanical and thermal load conditions according the regulatory requirements. KW - Package KW - Safety KW - Storage KW - Transport KW - Testing KW - Convection KW - Fire test KW - Heat KW - Insulation KW - Thermal analysis PY - 2015 SN - 978-1-78242-309-6 SN - 978-1-78242-322-5 DO - https://doi.org/10.1016/B978-1-78242-309-6.00008-3 N1 - Serientitel: Woodhead publishing series in energy – Series title: Woodhead publishing series in energy IS - 78 SP - Chapter 8, 107 EP - 121 PB - Woodhead Publ. AN - OPUS4-33842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Nehrig, Marko A1 - Bletzer, Claus Wilhelm A1 - Musolff, André A1 - Wille, Frank T1 - Combustion of wood encapsulated in steel sheets during fire test N2 - Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by Steel sheets. These impact limiters shall ensure the transport cask meets the IAEA safety requirements. After damage caused by the mechanical tests the package has to withstand a severe fire scenario. According to the regulations during and following the fire test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally. Due to results of the French institute IRSN it was shown that after the fire test an additional energy supply from a pre-damaged impact limiter should be taken into account. The combustion or smouldering of wood was of interest. BAM started a first test phase to examine the issue of combustion for such kind of package components. The goal was to understand the phenomena under the consideration of relevant regulatory boundary conditions. Several metal buckets were filled with wood and equipped with thermocouples. The test specimens have been prepared with different damage arrangements to take the influence of the mechanical tests into account. This paper shows the experimental Setup and the conduction of the tests. The first test shows that pre-damaged metal encapsulations can lead to smouldering of the wood and with this to a Supplement energy release after the end of the 30 minute fire. The consequence could be, to consider additional thermal loads of wood filled impact limiters to filled the IAEA regulations, if the conditions of the tests are transferable to the safety analysis of the package design. T2 - RAMTRANS 2015 - 10th International conference on radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Typ-B KW - Impact limiter KW - Shock absorber KW - Wood KW - Thermal test KW - Fire test PY - 2015 SP - 1 EP - 9 AN - OPUS4-33407 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Homogenität und Stabilität der Ringversuchs-Probe, Interlabory test 2010/11 DIN EN 15188:2007 T2 - Kolloquium des Arbeitskreises "Brennbare Stäube":Interlabory test 2010/11 DIN EN 15188:2007 - self-ignition temperature" CY - Dresden, Deutschland DA - 2013-01-29 PY - 2013 AN - OPUS4-33533 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wittig, Günther A1 - Thomas, Hans-Martin A1 - Maser, Dieter A1 - Hennig, P. T1 - Application of the pulsed-eddy-current techniques for the inspection of the austenitic cladding in a thermal shock loaded nozzle of a pressure vessel T2 - 6th International Conference on NDE in the Nuclear Industry and Equipment CY - Zürich, Switzerland DA - 1983-11-28 PY - 1984 SN - 0-87170-192-8 SP - 665 EP - 674 PB - American Society for Metals CY - Metals Park, Ohio AN - OPUS4-34232 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thomas, Hans-Martin A1 - Wittig, Günther T1 - Application of a signal reconstruction method to evaluate pulsed eddy-current signals PY - 1985 SN - 0308-9126 VL - 18 IS - 5 SP - 251 EP - 256 PB - Elsevier CY - Amsterdam AN - OPUS4-34228 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wittig, Günther A1 - Thomas, Hans-Martin A1 - Maser, Dieter T1 - Eigenschaften von Tastspulen für die Anwendung des Impuls-Wirbelstromverfahrens PY - 1985 SN - 0025-5300 VL - 27 IS - 5 SP - 123 EP - 126 PB - Carl Hanser Verlag CY - München AN - OPUS4-34229 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Kurz, J.H. A1 - Lanata, F. A1 - Krstevska, L. A1 - Cavalli, A. T1 - Needs for further developing monitoring- and NDT-methods for timber structures N2 - For the assessmentand for monitoring of timber structures there are numerous promising methods that enable the quantitative description of the current condition of construction elements or parts of a structure. This concerns material properties like modulus of elasticity, moisture content and density as well as structural properties like dynamic characteristics, localization of inhomogeneities, cracks, and biological attack. During the work in COST Action FP 1101, since 2012 the capability of experimental methods are discussed and compared. This covers electrical and electromagnetic wave methods (resistivity, microwave, Radar, X-Ray), elastic waves (ultrasound, pile testing) and mechanical testing (static and dynamic). Describing and collecting the use of the experimental methods for monitoring purposes was the objective of working group 3 "Monitoring of Timber Structures" of the COST Action. Monitoring capabilities will extend the use of timber structures to further applications in civil engineering. So far, no standard exists but collections of application examples and review papers representing the state of the art. From there needs for further developments regarding monitoring and NDT methods for timber structures can be identified and these are described in this paper. T2 - SHATIS 2015 - 3rd International conference on structural health assessment of timber structures CY - Wroclaw, Poland DA - 09.09.2015 KW - Holz Konstruktionen KW - Monitoring KW - Langzeitverhalten KW - Erdbebensicherheit KW - Historische Bauwerke KW - Ultrasonic echo imaging KW - Historical timber structures KW - Seismic investigation KW - Dynamic tests KW - Anisotropic wave propagation KW - Extending service life PY - 2015 VL - 1 SP - 1 EP - 12 AN - OPUS4-35178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Mayer, K. A1 - Effner, Ute T1 - Ultrasonic echo methods for structural timber N2 - Ultrasonic echo technique with shear waves in the frequency rang of 50 kHz is one of the promising methods for assessment of structural timber and is already frequently applied for this purpose. The article summarizes the state of the art of applying echo measurement via linear measurements as well as the development and first results for an imaging method for this purpose. The highly anisotropic properties of the ultrasonic velocity have to be considered. 3 D ultrasonic imaging results are described for the example of a pedestrian bridge made from Siberian larch. T2 - COST Workshop - Highly performing timber structures: Reliability, assessment, monitoring and strengthening CY - Biel, Switzerland DA - 23.09.2014 KW - Ultrasonic echo KW - SAFT reconstruction calculation KW - Glued-laminated timber (glulam) KW - Footbridge KW - Ultraschallecho KW - SAFT KW - Brettschichtholz PY - 2014 SN - 978-3-9523787-3-1 SP - 77 EP - 82 PB - Bern University of Applied Sciences CY - Bern AN - OPUS4-35179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Martin-Sanchez, Pedro Maria T1 - Contribution of culture-independent methods to the cave aerobiology; the case of Lascaux Cave T2 - International Workshop "The Conservation of Subterranean Cultural Heritage" CY - Seville, Spain DA - 2014-03-24 PY - 2014 AN - OPUS4-31623 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thomas, Hans-Martin A1 - Wittig, Günther A1 - Maser, Dieter T1 - Ein Impuls-Wirbelstromprüfsystem mit rechnergestützter Erfassung und Auswertung der Meßsignale PY - 1982 SN - 0025-5300 VL - 24 IS - 8 SP - 282 EP - 287 PB - Hanser CY - München AN - OPUS4-36415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Krause, Martin A1 - Wiggenhauser, Herbert T1 - Praxiseinsatz eines Ultraschall-Verfahrens zur Strukturuntersuchung von Betonbauteilen N2 - Einsatzbereiche des Meßsystems: - Ortung von Strukturelementen oder Verdichtungsmängeln in Beton - Dickenbestimmung von Bauteilen bei einseitiger Zugänglichkeit - Messung des Haftverbundes bei mehrschichtigen Bauteilen Auswerteverfahren: - Prinzip der laufzeitkorrigierten Überlagerung Vorteile: - Automatischer Meßablauf durch Array-Technik - Flexibler Einsatz durch lange Kabelverbindungen zwischen Prüfkopfarray und Meßapparatur T2 - Fachtagung Bauwerksdiagnose - Praktische Anwendungen Zerstörungsfreier Prüfungen CY - Munich, Germany DA - 21.01.1999 KW - Dickenmessung KW - Sohlplatte KW - Leerrohre PY - 1999 AN - OPUS4-36521 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Erdt, René A1 - Gödde, M. A1 - Salg, St. A1 - Ittemann, L. T1 - Selbstentzündungsverhalten von Feststoffen: Validierung der Extrapolation von Labortests mithilfe halbtechnischer Versuche bis 1 m3 N2 - Vorgestellt wird ein 2018 gestartetes Projekt zur Überprüfung der Extrapolation von im Labormaßstab ermittelten Selbstentzündungstemperaturen auf technisch relevante Volumina. Für die Ermittlung reaktionskinetischer Daten von Feststoffschüttungen stehen eine Reihe von Untersuchungsmethoden zur Verfügung. Dies sind thermische Analysen wie z. B. die differential scanning calorimetry DSC sowie Mikrokalorimetrie zur hochgenauen Messung von Wärmeströmen, bei denen sehr geringe Probenmengen zum Einsatz kommen. In der Regel wird das Selbstentzündungsverhalten jedoch mithilfe von isoperibolen oder adiabaten Warmlagerungsversuchen beurteilt, hier liegen die Probenvolumina üblicherweise im Bereich von ca. 100 cm3 bis zu einigen Litern. Die Extrapolation über mehrere Größenordnungen auf technische Volumina birgt Unsicherheiten, da mit Zunahme des Lagervolumens veränderte Start- und Randbedingungen vorliegen können. Zudem besteht die Möglichkeit, dass bei in technischen Lagern vorherrschenden niedrigen Temperaturen Reaktionen ablaufen, die in Standard- Laborversuchen nicht erfasst werden, aber einen wesentlichen Einfluss auf das Selbstentzündungsverhalten aufweisen können. Hauptziel des Projektes ist es daher, die im Labormaßstab vorhandenen Prüfeinrichtungen durch einen Versuchsstand zur Untersuchung von Probengrößen von bis zu 1000 dm3 zu erweitern, die Eignung (oder Nichteignung) der etablierten Methoden nachzuweisen und im Labormaßstab nicht erfassbare Einflussgrößen zu ermitteln. Zudem sollen anhand der kleinskaligen Tests Entscheidungskriterien abgeleitet werden, ob eine Extrapolation nach den derzeit üblichen Methoden zulässig ist. T2 - 15. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Brunswick, Germany DA - 21.05.2019 KW - Selbstentzündung KW - Formalkinetische Daten KW - Halbtechnische Versuche KW - Thermoanalytische Methoden PY - 2020 SN - 0030-834X VL - 130 IS - 1 SP - 9 EP - 18 AN - OPUS4-51285 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Günther, Martin A1 - Lorenzetti, A. A1 - Schartel, Bernhard T1 - From Cells to Residues: Flame-Retarded Rigid Polyurethane Foams N2 - Rigid polyurethane foams (RPUFs) exhibit short times to ignition as well as rapid flame spread and are therefore considered to be hazardous materials. This paper focuses on the fire phenomena of RPUFs, which were investigated through a multimethodological approach. Water-blown polyurethane (PUR) foams without flame retardants (FRs) as well as waterblown PUR foams containing triethyl phosphate as a gas phase-active FR were examined. The aim of this study is to clarify the influence of the FR on the fire phenomena during combustion of the foams. Additionally, materials’ densitieswere varied to range from 30 to 100 kg/m3. Thermophysical properties were studied bymeans of thermogravimetry; fire behavior and flammability were investigated via cone calorimeter and limiting Oxygen index, respectively. During the cone calorimeter test, the temperature development inside the burning specimens was monitored with thermocouples, and cross sections of quenched specimens were examined visually, giving insight into the morphological changes during combustion. The present paper delivers a comprehensive study, illuminating phenomena occurring during foam combustion and the influence of a FR active in the gas phase. The superior fire performance of flameretarded PUR foams was found to be based on flame inhibition, and on increased char yield leading to a more effective protective layer. It was proven that in-depth absorption of radiation is a significant factor for estimation of time to ignition. Cross sections investigated with the electron scanning microscope exhibited a pyrolysis front with an intact foam structure underneath. The measurement of temperature development inside burning specimens implied a shift of burning behavior towards that of non-cellular materials with rising foam density. KW - Polyurethane KW - Rigid foams KW - Fire behavior PY - 2020 DO - https://doi.org/10.1080/00102202.2019.1634060 SN - 0010-2202 SN - 1563-521X VL - 192 IS - 12 SP - 2209 EP - 2237 PB - Taylor & Francis AN - OPUS4-51483 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Uhlig, S. A1 - Frost, K. A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Schmidt, Martin A1 - Zakel, S. T1 - CEQAT-DGHS interlaboratory tests for chemical safety: Validation of laboratory test methods by determining the measurement uncertainty and probability of incorrect classification including so-called “Shark profiles” N2 - Laboratory test results are of vital importance for correctly classifying and labelling chemicals as “hazardous” as defined in the UN Globally Harmonized System (GHS) / EC CLP Regulation or as “dangerous goods” as defined in the UN Recommendations on the Transport of Dangerous Goods. Interlaboratory tests play a decisive role in assessing the reliability of laboratory test results. Interlaboratory tests performed over the last 10 years have examined different laboratory test methods. After analysing the results of these interlaboratory tests, the following conclusions can be drawn: 1. There is a need for improvement and validation for all laboratory test methods examined. 2. To avoid any discrepancy concerning the classification and labelling of chemicals, the use of validated laboratory test methods should be state of the art, with the results accompanied by the measurement uncertainty and (if applicable) the probability of incorrect classification. This paper addresses the probability of correct/incorrect classification (for example, as dangerous goods) on the basis of the measurement deviation obtained from interlaboratory tests performed by the Centre for quality assurance for testing of dangerous goods and hazardous substances (CEQAT-DGHS) to validate laboratory test methods. This paper outlines typical results (e.g. so-called “Shark profiles” – the probability of incorrect classification as a function of the true value estimated from interlaboratory test data) as well as general conclusions and steps to be taken to guarantee that laboratory test results are fit for purpose and of high quality. T2 - 13th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE 2020) CY - Braunschweig, Germany DA - 27.07.2020 KW - Dangerous goods KW - Hazardous substances KW - Interlaboratory test KW - Test method KW - Validation KW - Quality assurance KW - Measurement uncertainty KW - Incorrect classification KW - Shark profile PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-515376 UR - https://oar.ptb.de/files/download/5f3e662f4c93901010006dbf DO - https://doi.org/10.7795/810.20200724 VL - 2020 SP - 50 EP - 61 PB - Open Access Repository der Physikalisch-Technischen Bundesanstalt (PTB-OAR) CY - Braunschweig AN - OPUS4-51537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Heat Flux from Wood Filled Impact Limiter under Fire Conditions N2 - Packages for the transport of high-level radioactive material must withstand severe hypothetical accidents. Regulatory test conditions shall cover these severe accident conditions and consist of mechanical tests and a following thermal test. To withstand the mechanical tests heavy weight packages are often designed with impact limiters consisting of wood encapsulated in steel sheets. The thermal test is defined precisely in the IAEA-regulations as a 30 minute fully engulfing 800 °C fire. After the fire phase a pre-damaged impact limiter might continue burning or smouldering and influence the cask thermal behaviour with its energy release. The energy transferred from the impact limiter to the cask is of importance for the safety of transport packages. A full-scale fire test with an impact limiter of 2.3 m in diameter and filled with spruce wood was designed and performed. The impact limiter continued burning for 3 days. Energy transfer and temperature measurements were performed. T2 - 9th International Scientific Conference - wood & fire safety 2020 CY - Online meeting DA - 02.11.2020 KW - Fre KW - Smouldering KW - Wood PY - 2020 AN - OPUS4-51517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Günther, Martin A1 - Levchik, S. V. A1 - Schartel, Bernhard T1 - Bubbles and collapses: Fire phenomena of flame-retarded flexible polyurethane foams N2 - Flexible polyurethane foams (FPUF) are easy to ignite and exhibit rapid flame spread. In this paper, the fire phenomena of two standard foam formulations containing tris (1,3-dichloro-2-propyl) phosphate (FR-2) and a halogen-freepoly (ethyl ethylene phosphate) (PNX), respectively, as flame retardants are compared. A multimethodological approach is proposed which combines standard fire tests as well as new investigatory approaches. The thermophysical properties of the foams were determined by thermogravimetric analysis (TG), reaction to small flames was studied by means of the limiting oxygen index (LOI) and UL 94 HBF test, and the burning behavior was investigated with the cone calorimeter. Further, temperature development in burning cone calorimeter samples was monitored using thermocouples, and rheological measurements were performed on pyrolyzed material, delivering insight into the dripping behavior of the foams. This paper gives comprehensive insight into the fire phenomena of flame-retarded FPUFs that are driven by the two-step decomposition behavior of the foams. LOI and UL 94 HBF tests showed a reduced flammability and reduced tendency to drip for the flame-retarded foams. TG and cone calorimeter measurements revealed that the two-step decomposition behavior causes two stages during combustion, namely structural collapse and pool fire. The flame-retardant mode of action was identified to take place primarily during the foam collapse and be based mainly on flame inhibition. However, some condensed-phase action was been measured, leading to significantly increased melt viscosity and improved dripping behavior for foams containing PNX. KW - Burning behavior KW - Flame retardant KW - Flexible PU foam PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-512145 DO - https://doi.org/10.1002/pat.4939 SN - 1042-7147 SN - 1099-1581 VL - 31 IS - 10 SP - 2185 EP - 2198 PB - Wiley Online Libary AN - OPUS4-51214 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Outcomes of three large scale fire reference tests conducted in BAM fire test facility N2 - Packages for the transport of high-level radioactive material are designed to withstand severe accidents. Hypothetical severe accident conditions are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials. One of these accident conditions is the thermal test, mainly consisting of a 30 minute fully engulfing 800°C pool fire or an equally severe fire test. The heat fluxes into the package depend substantially on the fire characteristics and the Surface temperature of the package. Fire tests can be performed at BAM on a propane gas fire test facility. In order to investigate the heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for multiple use. The package represented the outer geometry of a specific transport cask for radioactive waste. The fire reference package is a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 1500 mm and a diameter of 1050 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Three open-air fire tests were performed in the BAM propane gas fire test facility. The flames exposure time period varied slightly for the fire tests. The wind direction as well as the wind Speed were measured and changed between and during the tests. Test stand parameters such as wind shield location and propane gas volume flow were chosen constant for the three tests. The locally measured fire reference package steel sheet temperatures were used for the calculation of heat fluxes as function of time and surface temperature. The measured temperatures allowed further calculations. In a first approach effective fire characteristics of the propane gas fire, including the flame temperature, the fire convection coefficient and a Radiation exchange coefficient mathematically describing the determined average heat flux over the surface temperature were calculated. T2 - Pressure Vessels & Piping Conference 2020 CY - Online meeting DA - 03.08.2020 KW - Fire KW - Testing KW - Large scale testing KW - Calorimeter KW - Heat flux PY - 2020 SP - 1 EP - 9 PB - ASME CY - New York AN - OPUS4-51192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Outcomes of three large scale fire reference tests conducted in BAM fire test facility N2 - Packages for the transport of high-level radioactive material are designed to withstand severe accidents. Hypothetical severe accident conditions are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials. One of these accident conditions is the thermal test, mainly consisting of a 30 minute fully engulfing 800°C pool fire or an equally severe fire test. The heat fluxes into the package depend substantially on the fire characteristics and the Surface temperature of the package. Fire tests can be performed at BAM on a propane gas fire test facility. In order to investigate the heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for multiple use. The package represented the outer geometry of a specific transport cask for radioactive waste. The fire reference package is a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 1500 mm and a diameter of 1050 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Three open-air fire tests were performed in the BAM propane gas fire test facility. The flames exposure time period varied slightly for the fire tests. The wind direction as well as the wind Speed were measured and changed between and during the tests. Test stand parameters such as wind shield location and propane gas volume flow were chosen constant for the three tests. The locally measured fire reference package steel sheet temperatures were used for the calculation of heat fluxes as function of time and surface temperature. The measured temperatures allowed further calculations. In a first approach effective fire characteristics of the propane gas fire, including the flame temperature, the fire convection coefficient and a Radiation exchange coefficient mathematically describing the determined average heat flux over the surface temperature were calculated. T2 - Pressure Vessels & Piping Virtual Conference 2020 CY - Online meeting DA - 03.08.2020 KW - Fire KW - Testing KW - Convection coefficient KW - Large scale fire testing KW - Propane gas fire test facility PY - 2020 AN - OPUS4-51194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -