TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Conclusions from the first return campaign of vitrified High-Level Waste on sea going vessels from the competent authority N2 - Germany has to take back vitrified waste from the reprocessing plants in France and Great Britain. The waste resulted from decades of transporting spent fuel for reprocessing to La Hague and Sellafield. The return campaign from France was concluded in 2024 with the transport of five CASTOR® HAW28M casks to the interim storage facility in Philippsburg in southern Germany. The return of waste from Sellafield comprises three campaigns and a total of 20 CASTOR® HAW28M casks. The first campaign was performed in 2020, consisting of six CASTOR® HAW28M casks, while the second campaign was performed in March 2025, consisting of seven CASTOR® HAW28M casks. The casks were transported by rail from Sellafield to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. The third campaign is expected to be performed during 2026. BAM as part of the German competent authority system was among others involved in the assessment of the sea transport. BAM required for the first transport, among others, an assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of the IMDG code and its supplement the INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - PATRAM 2025 CY - San Antonio, Texas, USA DA - 27.07.2025 KW - RAM KW - Transport KW - Radioactive material KW - Sea PY - 2025 SP - 1 EP - 8 PB - INMM CY - Washington D.C. AN - OPUS4-63984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kang, Chongjie A1 - Arcones, Daniel Andrés A1 - Becks, Henrik A1 - Beetz, Jakob A1 - Blankenbach, Jörg A1 - Claßen, Martin A1 - Degener, Sebastian A1 - Eisermann, Cedric A1 - Göbels, Anne A1 - Hegger, Josef A1 - Hermann, Ralf A1 - Kähler, Philipp A1 - Peralta, Patricia A1 - Petryna, Yuri A1 - Schnellenbach‐Held, Martina A1 - Schulz, Oliver A1 - Smarsly, Kay A1 - Fatih Sönmez, Mehmet A1 - Sprenger, Bjarne A1 - Unger, Jörg F. A1 - Vassilev, Hristo A1 - Weiser, Martin A1 - Marx, Steffen T1 - Intelligente digitale Methoden zur Verlängerung der Nutzungsdauer der Nibelungenbrücke N2 - Um die Lebensdauer von Bauwerken unter Wahrung derer Standsicherheit und Funktionsfähigkeit zu verlängern, bedarf es effektiver Monitorings‐ sowie Instandhaltungskonzepte. Im Rahmen des von der Deutschen Forschungsgemeinschaft (DFG) geförderten Schwerpunktprogramms 2388 „Hundert plus – Verlängerung der Lebensdauer komplexer Baustrukturen durch intelligente Digitalisierung“ (kurz: SPP 100+) werden hierfür innovative, interdisziplinäre Methoden entwickelt und an der Nibelungenbrücke in Worms (NBW) validiert. Der vorliegende Beitrag stellt einige dieser neuentwickelten digitalen Methoden vor. Unter anderem umfasst dies zwei Systeme des Structural Health Monitoring (SHM) und deren zielorientierte Verknüpfung von mehreren Beschleunigungsmessdaten zur umfassenden Zustandsbewertung. Ergänzend werden innovative datenbasierte Simulationsmethoden zur Bestimmung des Temperaturfelds des Brückenüberbaus vorgestellt sowie mehrere Finite‐Elemente‐Modelle unterschiedlicher Detailtiefe präsentiert und miteinander verglichen. Abschließend werden innovative Methoden zum Verwalten des Bestandswissens von Brückenbauwerken diskutiert. Die Methoden wurden überwiegend unabhängig voneinander entwickelt und an der NBW validiert. Im nächsten Schritt werden die Methoden integriert, um die Instandhaltung der NBW zu unterstützen. KW - Nibelungenbrücke Worms KW - Digitaler Zwilling KW - Prädiktive Instandhaltung KW - Bauwerksmonitoring KW - Nachrechnung KW - Verkehrsinfrastruktur KW - FE-Modell PY - 2025 DO - https://doi.org/10.1002/best.70070 SN - 0005-9900 VL - 121. Jahrgang 2026 SP - 1 EP - 18 PB - Ernst & Sohn a Wiley Brand CY - Wien, Austria AN - OPUS4-65288 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Casperson, Ralf A1 - Leinenbach, F. A1 - Martin, J. ED - Meyendorf, N. ED - Ida, N. ED - Singh, R. ED - Vrana, J. T1 - DICONDE: Enabling FAIR Data and Communication in NDE 4.0 N2 - For the digital transformation and the integration of NDE into the Industry 4.0, standardized data formats and communication interfaces are mandatory. The Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE), based on Digital Imaging and Communication in Medicine (DICOM), offers both a standardized data format and standardized communication interfaces. Furthermore, DICONDE meets the requirements of the EU Data Act by supporting the FAIR data principle (findable, accessible, interoperable, and reusable data). DICONDE standards are available for radiography including computed tomography, ultrasonic, and eddy current testing. Standards for thermography and secondary capture are under development. The basic concept of DICONDE, storage of eddy current and ultrasonic raw data, and the use case of railway rail inspection at the AIFRI project are discussed in detail. KW - Data format KW - Data communication KW - FAIR data KW - NDE 4.0 KW - Industry 4.0 KW - EU Data Act KW - DICONDE PY - 2025 SN - 978-3-030-48200-8 DO - https://doi.org/10.1007/978-3-030-48200-8 SP - 1 EP - 20 PB - Springer Nature CY - Heidelberg ET - 2 AN - OPUS4-62657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Dengiz, Nizametin A1 - Fuchs, Martin A1 - Gaal, Mate A1 - Gautzsch, Tobias A1 - Herzog, Thomas A1 - Kornely, Mike A1 - Littner, Linus A1 - Marhenke, Torben A1 - Schmid, Simon A1 - Sommerhuber, Ryan A1 - Steinhausen, Ralf A1 - Szewieczek, Artur A1 - Wachter, Luis A1 - Waschkies, Thomas A1 - Wunderl, Stefan T1 - Leitfaden zur Durchführung von luftgekoppelter Ultraschallprüfung N2 - Die Anwendungsgebiete der luftgekoppelten Ultraschallprüfung (ACUT) können sehr vielfältig sein und weichen häufig stark von den Einsatzgebieten der klassischen Ultraschallprüfung ab. Vielmehr ist die ACUT eine eigenständige Methode, welche sich häufig eher mit Röntgen oder Thermografie überschneidet oder Prüfungen ermöglicht, die bis heute gar nicht verlässlich zerstörungsfrei durchgeführt werden können. Obwohl die luftgekoppelte Ultraschallprüfung mittlerweile keine neue Technologie ist, bleibt sie im Vergleich zu anderen Verfahren der ZfP ein Randgebiet unter den Methoden. Dies kommt nicht zuletzt dadurch zustande, dass es an Normen, Fachbüchern und Ausbildungsmöglichkeiten für interessierte Prüfer und Prüfaufsichten mangelt. Dies schafft für viele Anwendungsgebiete eine Einstiegshürde, welche die häufigere Anwendung verhindert. Aus diesen Gründen haben sich Experten aus Forschungseinrichtungen und aus der Industrie entschieden, einen Unterausschuss „Luftgekoppelte Ultraschallprüfung“ (ACUT) als Teil des Fachausschusses Ultraschallprüfung der DGZfP einzurichten und dort diese Themen zu bearbeiten. Es wurde beschlossen, einen Leitfaden zu erarbeiten, der interessierten Anwendern den Einstieg in ACUT erleichtert und eine Hilfestellung bei der Spezifikation und Umsetzung von solchen Prüfungen gibt. Das vorliegende Dokument ist das Ergebnis dieser Zusammenarbeit. KW - Luftgekoppelter Ultraschall KW - Ultraschallprüfung KW - Leitfaden PY - 2025 UR - https://publikationen.dgzfp.de/shop/leitfaden-zur-durchfuehrung-von-luftgekoppelter-ultraschallpruefung/ SN - 978-3-947971-45-9 VL - Richtlinie ACUT SP - 1 EP - 28 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin ET - Ausgabe Januar 2025 AN - OPUS4-62491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwettmann-Lui, Kim A1 - Nytus, Nina A1 - Weigel, Sandra A1 - Radenberg, Martin A1 - Stephan, Dietmar T1 - Effect of multiple-repeated aging and rejuvenation processes on bitumen properties evaluated with physical and chemical tests and multivariate analysis methods N2 - This paper presents laboratory experiments on repeated bitumen aging and rejuvenation processes to assess multiple reuse feasibility. Three 50/70 penetration-graded bitumen samples were reused with four different rejuvenators without adding virgin binder. The experiments continued until significant material changes, such as inhomogeneities and increased stickiness, prevented reliable characterization. After each rejuvenation and aging process, physical and chemical properties were analyzed, resulting in a comprehensive dataset. Results indicate that the reuse of pure rejuvenators, without incorporating virgin binder, is limited. Cyclic reuse depends heavily on the rejuvenator and its interaction with the binder. Of the four rejuvenators tested, two bio-based products enabled the maximum reuse of four cycles. Therefore, the rejuvenators used in this project are more suitable as additives to improve the physical properties of the bitumen for reuse rather than as substitutes for the binder. The datasets were further evaluated using multivariate analysis methods to construct statistical models for two use cases: In the first use case, the samples are classified by their aging condition. In the second use case, the samples are differentiated according to the rejuvenators. The models were successfully validated, providing a promising framework for the classification of unknown bitumen samples for reuse. KW - Bitumen KW - Aging KW - Rejuvenation KW - Multiple recycling KW - DSR measurements KW - Reuse KW - FTIR spectroscopy KW - Multivariate analysis methods PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627563 DO - https://doi.org/10.1016/j.conbuildmat.2025.140734 SN - 1879-0526 VL - 472 SP - 1 EP - 16 PB - Elsevier Ltd. AN - OPUS4-62756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poka, Konstantin A1 - Ali, Sozol A1 - Saeed, Waleed A1 - Merz, Benjamin A1 - Epperlein, Martin A1 - Hilgenberg, Kai T1 - Quality assurance via a cyber physical system of a PBF-LB/M machine N2 - Powder Bed Fusion with Laser Beam of Metals (PBF-LB/M) faces challenges in reproducibility and quality assurance, even for widely applied alloys like AlSi10Mg. This work introduces a digital provenance framework for PBF-LB/M, showcased through the EOS M 300–4 multi-laser machine. An Extract, Transform, Load (ETL) pipeline autonomously captures machine data, including scan vectors as well as process signals, and organizes them into a Digital Shadow (DS). The DS is further extended by external data sources, such as Melt Pool Monitoring (MPM), to enable comprehensive analysis and root cause identification. This approach ensures continuous data representation and facilitates the development of new quality metrics. Moreover, the framework enhances quality assurance and traceability, supports compliance with industry standards, and improves productivity. It also enables more precise cost calculations and predictive maintenance. By addressing these challenges, the framework is essential for advancing PBF-LB/M in industrial applications, achieving greater consistency and scalability in production. KW - PBF-LB/M KW - Data driven quality assurance KW - Data engineering KW - Digital shadow PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625187 DO - https://doi.org/10.1007/s40964-025-00978-w SN - 2363-9520 VL - 10 IS - 3 SP - 1771 EP - 1783 PB - Springer Science and Business Media LLC AN - OPUS4-62518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Recknagel, Christoph A1 - Eilers, Manfred A1 - Hoppe, Johannes A1 - Cetinkaya, Reha A1 - Machill, Nicole A1 - Weitz, Dennis A1 - Zscherpe, Oliver A1 - Sikinger, Thomas A1 - Loher, erich A1 - Oelerich, Martin A1 - Schäfer, Volker A1 - Schäfer, Thorsten A1 - Uslu, Cenk A1 - Virnau, Lucas A1 - Dudenhöfer, Bernd A1 - Rückert, Phillip A1 - Alte-Teigeler, Ralf A1 - Rau, Richard T1 - Merkblatt für die Herstellung von Abdichtungssystemen aus hohlraumreichen Asphalttraggerüsten mit nachträglicher Verfüllung (HANV) für Ingenieurbauten aus Beton N2 - Konventionelle Regelbauweisen für die Ausbildung von Abdichtungssystemen auf Brücken- und anderen Ingenieurbauwerken aus Beton machen signifikante material- und systembedingte Einbau- und Sperrzeiten erforderlich. Das innovative Abdichtungssystem „Hohlraumreiches Asphalttraggerüst mit nachträglicher Verfüllung“ (kurz: HANV) bietet eine deutliche Zeitersparnis von Ausführung bis Verkehrsfreigabe. Gleichzeitig zeichnet sich diese Bauweise mit einer hohen Deformationsbeständigkeit gegenüber Schwerlastverkehr aus. Auf der Grundlage eines mittlerweile ausgeprägten Erfahrungshintergrundes wird mit Hilfe des aufgestellten Regelwerkes der Baupraxis eine qualitätssichere Ausführung mit gütegesicherter Funktionalität zur Verfügung gestellt. KW - Abdichtungssysteme KW - Verkehrs-Infrastrukutur KW - Ingenieurbauwerke aus Beton PY - 2025 SN - 978-3-86446-421-8 VL - 2025 IS - 1 SP - 3 EP - 40 PB - FGSV-Verlag CY - Wesselinger Straße 15-17 in 50999 Köln ET - 1. Auflage AN - OPUS4-62798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martin, T. A1 - Zimmermann, E. A1 - Klitzsch, N. A1 - Hördt, A. A1 - Huisman, J. A. A1 - Radic, T. A1 - Kruschwitz, Sabine T1 - Round-robin test of SIP laboratory measurements using electrical test networks N2 - This study presents the results of an interlaboratory test designed to evaluate the accuracy of spectral induced polarization (SIP) measurements using controlled electrical test networks. The study, conducted in Germany since 2006, involved 12 research institutes, six different impedance measurement devices and four types of electrical test networks specifically designed to evaluate phase shift errors in SIP measurements. The test networks, with impedances ranging from 100 to 150 kΩ, represent high-impedance samples with different phase characteristics, and pose the measurement challenges typical of such samples, including high contact impedances and parasitic capacitances. Four key findings emerged from the study: (1) Impedance measurements across all devices showed deviations within 1 per cent over a wide frequency range (0.001–1000 Hz); (2) phase errors remained below 1 mrad up to 100 Hz for most devices, but increased at higher frequencies due to parasitic capacitances and electromagnetic coupling effects; (3) lab-specific instruments have lower phase errors than field instruments when used in a laboratory environment, primarily due to the effects of long cables and too low input impedances of the field instruments; and (4) short cables and driven shielding technology effectively minimized parasitic capacitance and improved measurement accuracy. The study highlights the usefulness of test networks in assessing the accuracy of SIP measurements and raises awareness of the various factors influencing the quality of SIP data. KW - Induced polarization KW - Electrical properties KW - Electrical resistivity tomography (ERT) PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631522 DO - https://doi.org/10.1093/gji/ggaf153 SN - 0956-540X VL - 242 IS - 1 SP - 1 EP - 13 PB - Oxford University Press (OUP) AN - OPUS4-63152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Reichel, Levin A1 - Schröpfer, Dirk A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Modern welding processes for optimising repair welds on high strength offshore steels N2 - The successful energy transition in Germany will require offshore wind turbines with outputs >10 MW in the future. To achieve these high outputs, turbines far from coast are required with large subsea jacket structures (30 m up to 50 m) and tall towers (up to 200 m). High-strength steels with a yield strength up to 500 MPa and wall thicknesses up to 150 mm are increasingly being used for these structures. This plac-es high demands on welding manufacturing, especially for high-strength offshore steels. During the manu-facturing process detected defects by NDT require localized repair of welds by gouging and rewelding. Due to a lack of investigations, there are no repair concepts and information in standards and guidelines, par-ticularly for high-strength thick plate joints made of high-strength offshore steels. However, these are ur-gently needed to enable manufacturers, especially SMEs, to carry out safe and economical repairs. There-fore, BAM started the FOSTA project P1629 (IGF 01IF22746N) to investigate the stress-optimized repair (local gouging and welding) of high-strength thick plate joints made of offshore grades in the yield strength range off 355 to 460 MPa and similar weld metal with controlled high-performance GMAW pro-cesses and optimized narrow gouging grooves. The experimental analyses take into account the complex interaction of process, material, and design-related influences on the formation of weld induced stresses and the special microstructure of high-strength fine-grain structural steels. Welding-related material degra-dation and crack-critical residual tensile stresses need to be avoided to ensure high component safety and performance. A reduction in residual stress in the presence of high restraint conditions can be achieved by adapted heat control (if no disassembly measures are possible). The repair process involves manual thermal gouging, which allows the groove configuration to be modi-fied. Modern welding processes using high frequency arc control provide deep root penetration and focused energy input capable of welding narrow seams. A comparison was made between the traditional weld con-figuration with a wide 45° groove and transition arc welding and a narrow 30° groove with modern welding process. Even in the case of free shrinkage specimens, the narrow groove weld exhibits a significant reduc-tion of residual stresses, cf. Figure 1, especially in the HAZ and toward the adjacent base material. This can be attributed to the lower weld metal volume needed and the reduction of heat input per layer due to the controlled arc process. For the purposes of this comparison, the same weld seam build-up (but different number of layers) has been applied to both seam configurations. Note that in industrial application (manu-al welding), the wider groove would be welded with several off-center weld beads with conventional weld-ing process. In this analysis this would cause asymmetric effects regarding the residual stress state, diffi-cult to compare to each other. Component-related welding experiments on special testing equipment, adapted process and heat control concepts along with variable groove configurations will be developed and recommendations for guidelines elaborated. This is the prerequisite for fully utilizing the strength potential of high-strength steels and making a valuable contribution to the energy transition in Germany, especially for steel-processing SMEs. T2 - IIW Intermediate Meeting CII CY - Trollhättan, Sweden DA - 10.03.2025 KW - Repair welding KW - Gouging KW - Residual stress KW - Offshore wind turbines KW - High-strength steels PY - 2025 AN - OPUS4-62743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Dittmann, Florian A1 - Varfolomeev, Igor T1 - Untersuchung der Ermüdungsfestigkeit von LTT-geschweißten Längssteifen mit variierender Nahtausführungen N2 - Low Transformation Temperature (LTT) Schweißzusätze erzeugen während der Abkühlung Druckeigenspannungen in die Schweißnaht und Wärmeeinflusszone durch eine Volumenexpansion, wodurch die Ermüdungsfestigkeit erhöht werden kann. Um das Potential dieser neuartigen Schweißzusätze besser zu quantifizieren, wurden konventionelle Längssteifen als Probenkörper verwendet, welche an den Stirnseiten mit einer LTT-Zusatznaht geschweißt wurden. Durch Variation der Schweißparameter konnten unterschiedliche Nahtformen realisiert werden. Es konnte, je nach Nahtausführung, eine Erhöhung der Ermüdungsfestigkeit bei 2 Millionen Lastwechsel von 64 MPa bis 100 MPa in Gegensatz zu konventionellen Proben festgestellt werden. Somit sind LTT-Zusätze grundsätzlich geeignet, um die Ermüdungsfestigkeit zu erhöhen. T2 - Frühjahrssitzung 2025 des Fachausschusses Eigenspannungen der AWT CY - Karlsruhe, Germany DA - 07.04.2025 KW - LTT (Low Transformation Temperature) KW - Eigenspannungen KW - Ermüdungsfestigkeit KW - Aufmischung PY - 2025 AN - OPUS4-62930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Dittmann, Florian A1 - Varfolomeev, Igor T1 - Wechselwirkung zwischen Nahtgestaltung und Ermüdungsfestigkeit in LTT-geschweißten Längssteifen N2 - Schweißzusätze mit niedriger Martensitstarttemperatur (Low Transformation Temperature, LTT) induzieren während der Abkühlphase infolge einer volumeninduzierten Martensitumwandlung Druckeigenspannungen in der Schweißnaht sowie in der angrenzenden Wärmeeinflusszone (WEZ). Diese Spannungen können zu einer signifikanten Erhöhung der Ermüdungsfestigkeit führen. Zur quantitativen Bewertung des Potenzials dieser innovativen Werkstoffe wurden konventionelle Längssteifen als Versuchsproben herangezogen, bei denen an den Stirnseiten Schweißnähte unter Verwendung von LTT-Zusatzwerkstoffen appliziert wurden. Durch gezielte Variation der Schweißparameter konnten unterschiedliche Nahtgeometrien realisiert werden. In Abhängigkeit von der Nahtausführung zeigte sich bei einer Belastungszahl von 2 Millionen Zyklen eine Steigerung der Ermüdungsfestigkeit im Bereich von 64 MPa bis 100 MPa im Vergleich zu Referenzproben mit herkömmlichen Schweißzusätzen. Die Ergebnisse belegen, dass der Einsatz von LTT-Schweißzusätzen grundsätzlich geeignet ist, die Ermüdungsfestigkeit geschweißter Strukturen zu verbessern. T2 - Din Sitzung: Gemeinschaftsarbeitsausschuss NAS/NMP, Zerstörende Prüfung von Schweißverbindungen CY - Online meeting DA - 20.03.2025 KW - LTT (Low Transformation Temperature) KW - Eigenspannungen KW - Ermüdungsfestigkeit KW - high-strength steels PY - 2025 AN - OPUS4-62929 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Blind, Knut A1 - Gutknecht, Ralph A1 - Kirstgen, Martin A1 - Neuhäusler, Peter A1 - Schirmeister, Elna A1 - Schubert, Torben ED - Koch, Claudia T1 - Die Bedeutung der Qualitätsinfrastruktur: Studie zu wirtschaftlichen und nicht-wirtschaftlichen Wirkungen sowie Trendstudie Digitalisierung N2 - Um Qualität, Sicherheit und Umweltverträglichkeit von Waren, Dienstleistungen und Verfahren zu unterstützen und zu verbessern braucht es eine starke und verlässliche Qualitätsinfrastruktur (QI). Die empirische Studie erfasst erstmals quantitativ die wirtschaftlichen und nicht-wirtschaftlichen Wirkungen der QI. Im Rahmen dieser Studie wurden die ökonomischen Wirkungsdimensionen der QI und ihrer Einzelkomponenten, insb. im Hinblick auf Bruttowertschöpfung, Wirtschaftswachstum, Außenhandel, Innovation, und weitere Aspekte konzeptionell erfasst und quantifiziert. Dabei wurden sektorspezifische Besonderheiten berücksichtigt. Komplementär wurden auch ausgewählte nicht-ökonomische Wirkungsdimensionen der QI quantitativ bestimmt. Diese quantitative Analyse wird ergänzt durch eine qualitative Untersuchung der QI Deutschlands, wobei sowohl auf die Interaktionen der verschiedenen QI-Komponenten eingegangen als auch auf die Besonderheiten ausgewählter Sektoren abgehoben wird. Die Möglichkeiten der rasch voranschreitenden Digitalisierung für die QI und ihre einzelnen Komponenten wurden in einem zweiten Teil im Rahmen eines Szenarioansatzes identifiziert und bewertet. Hier wurden auf Basis von Schlüsselfaktoren vier Szenarien entwickelt und entsprechende strategische Implikationen und Anknüpfungspunkte abgeleitet. Abschließend gibt die Studie Empfehlungen differenziert nach den einzelnen Komponenten der QI, aber auch speziell für verschiedenen Akteure und Institutionen auf Basis der gewonnenen Erkenntnisse. KW - Qualitätsinfrastruktur KW - Wirtschaftsleistung KW - Trendanalyse KW - Szenarioanalyse KW - Szenarien PY - 2025 DO - https://doi.org/10.24406/publica-4411 N1 - Endbericht zu einem Projekt im Rahmen von QI-Digital, gefördert vom Bundesministerium für Wirtschaft und Klimaschutz. SP - 1 EP - 154 PB - Fraunhofer-Institut für System- und Innovationsforschung (ISI) CY - Karlsruhe AN - OPUS4-62710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed A. A1 - Böhning, Martin A1 - De Souza, N. R. A1 - Juranyi, F. A1 - Zorn, R. A1 - Schönhals, Andreas T1 - Inelastic and Quasielastic Neutron Scattering on Polynorbornenes with Bulky Carbocyclic Side groups N2 - This study investigates the molecular mobility and vibrational properties of polynorbornenes with bulky carbocyclic side groups using inelastic and quasielastic neutron scattering techniques. The polymers, synthesized via metathesis and addition polymerization, exhibit varying degrees of microporosity, which ignificantly influences their gas separation performance. By inelastic neutron scattering experiments, it could be shown that all considered polymers have excess contributions to the low frequency vibrational density of states known as the Boson peak. The maximum frequency of the Boson peak correlates to the microporosity of the polymers. This correlation supports the sound wave interpretation of the Boson peak, suggesting that the microporous structure enhances the compressibility of the material at a microscopic length scale. The molecular mobility, particularly the methyl group rotation, was characterized using elastic scans and quasielastic neutron scattering. The study revealed a temperature dependent relaxation process, with the onset of molecular fluctuations observed around 200 K for the polymer containing methyl groups. For the polymer having no methyl groups only elastic scattering is observed. The methyl group rotation was analyzed in terms of a jump diffusion in a threefold potential with three equivalent energy minima. This leads to an almost correct description of the q dependence of the elastic incoherent scattering function when the number of hydrogen nuclei undergoing the methyl group rotation is considered. It was further evidenced that the fraction of methyl undergoing the methyl group rotation increases with increasing temperature. KW - Polymers of Intrinsic Microporosity KW - Neutron scattering PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630297 DO - https://doi.org/10.1016/j.polymer.2025.128358 SN - 1873-2291 VL - 328 SP - 241 PB - Elsevier Ltd. AN - OPUS4-63029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -