TY - JOUR A1 - Schmidt, Martin A1 - Wu, D. A1 - Norman, F. A1 - Vanierschot, M. A1 - Verplaetsen, F. A1 - Berghmans, J. A1 - van den Bulck, E. T1 - Numerical investigation on the self-ignition behaviour of coal dust accumulations: The roles of oxygen, diluent gas and dust volume N2 - Self-ignition of coal dust deposits poses a higher risk of fires in oxygen-enriched oxy-fuel combustion systems. In this work, we develop a numerical method, using the commercial software COMSOL Multiphysics, to investigate self-ignition behaviour of coal dust accumulations with a main emphasis on the roles of oxygen, diluent gas and dust volume. A one-step 2nd-order reaction kinetic model considering both coal density and oxygen density is used to estimate reaction rate using the kinetic parameters from previously conducted hot-oven tests. This model is validated to predict the transient temperature and concentration profiles of South African coal dusts until ignition. The computed self-ignition temperatures of dust volumes show a good agreement with experimental results. In addition, it is found that the inhibiting effect of carbon dioxide is comparatively small and oxygen consumption increases dramatically after ignition. Parameter analysis shows that the heating value and kinetic parameters have a comparatively pronounced effect on self-ignition temperature. The model provides a satisfactory explanation for the dependence of self-ignition behaviour on gas atmospheres, thus helping to further understand the fire risk of self-ignition in oxy-fuel combustion systems. KW - Ignition temperature KW - Oxy-fuel combustion KW - Fire safety KW - Self-ignition KW - Numerical simulation PY - 2017 DO - https://doi.org/10.1016/j.fuel.2016.10.063 SN - 0016-2361 SP - 500 EP - 510 AN - OPUS4-37885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seewald, J.S. A1 - Reeves, E.P. A1 - Bach, W. A1 - Saccocia, P.J. A1 - Craddock, P.R. A1 - Shanks III, W.C. A1 - Sylva, S.P. A1 - Pichler, T. A1 - Rosner, Martin A1 - Walsh, E. T1 - Submarine venting of magmatic volatiles in the Eastern Manus Basin, Papua New Guinea N2 - The SuSu Knolls and DESMOS hydrothermal fields are located in the back-arc extensional transform zone of the Eastern Manus Basin. In 2006, highly acidic and ΣSO4-rich vent fluids were collected at both sites and analyzed for the chemical and isotopic composition of major and trace species. Fluids exiting the seafloor have measured temperatures from 48 to 215 °C and are milky white in appearance due to precipitation of elemental S0. Vent fluid concentrations of Na, K, and Mg are depleted by as much as 30% relative to seawater, but have the same relative abundance. In contrast, the fluids are highly enriched in dissolved ΣCO2, Cl, SiO2(aq), Fe, and Al relative to seawater. Measured pH (25 °C) ranged from 0.95 to 1.87 and aqueous ΣSO4 ranged from 35 to 135 mmol/kg. The chemical and isotopic composition points to formation via subsurface mixing of seawater with a Na-, K-, Mg-, and Ca-free, volatile-rich magmatic fluid exsolved from subsurface magma bodies during a process analogous to subaerial fumarole discharge. Estimates of the magmatic end-member composition indicate a fluid phase where H2O > SO2 > CO2 ≈ Cl > F. The hydrogen and oxygen isotopic composition of H2O and carbon isotopic composition of ΣCO2 in the vent fluids strongly suggest a contribution of slab-derived H2O and CO2 to melts generated in the mantle beneath the Eastern Manus volcanic zone. Abundant magmatically-derived SO2 undergoes disproportionation during cooling in upflow zones and contributes abundant acidity, SO42-, and S0 to the venting fluids. Interaction of these highly acidic fluids with highly altered mineral assemblages in the upflow zone are responsible for extensive aqueous mobilization of SiO2(aq), Fe, and Al. Temporal variability in the speciation and abundance of aqueous S species between 1995 and 2006 at the DESMOS vent field suggests an increase in the relative abundance of SO2 in the magmatic end-member that has mixed with seawater in the subsurface. Results of this study constrain processes responsible for the formation of hot-spring fluids in magmatically active back-arc environments and the resulting chemical exchange between the lithosphere and water column. PY - 2015 DO - https://doi.org/10.1016/j.gca.2015.04.023 SN - 0016-7037 SN - 1872-9533 VL - 163 SP - 178 EP - 199 PB - Elsevier Science CY - New York, NY AN - OPUS4-33433 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bentrup, U. A1 - Radnik, J. A1 - Armbruster, U. A1 - Martin, A. A1 - Leiterer, Jork A1 - Emmerling, Franziska A1 - Brückner, A. T1 - Linking simultaneous in situ WAXS/SAXS/Raman with Raman/ATR/UV-vis spectroscopy: comprehensive insight into the synthesis of molybdate catalyst precursors N2 - A new setup is presented which enables simultaneous wide- and small-angle X-ray scattering (WAXS/SAXS) and Raman spectroscopic experiments during the synthesis of Mo-based mixed oxide catalyst precursors at the µ-spot beamline at the Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung (BESSY). Furthermore, we report about the separate monitoring of the same reactions under comparable conditions by simultaneous combined ATR/UV–vis/Raman spectroscopic measurements. For testing the performance of both experimental setups two syntheses were described comprising the precipitation of metal molybdates by mixing solutions of metal nitrates and ammonium heptamolybdate. Additionally, the effect of H3PO4 admixture on precipitation was investigated. The combined evaluation of spectroscopic and WAXS/SAXS data allows the discrimination between different molybdate species appearing in solution and precipitate. Furthermore, these molybdate species could be assigned to separate phases of different crystallinity. KW - In situ KW - WAXS/SAXS KW - Raman KW - ATR KW - UV-vis KW - Mixed oxide catalyst KW - Synthesis PY - 2009 DO - https://doi.org/10.1007/s11244-009-9309-y SN - 1022-5528 VL - 52 IS - 10 SP - 1350 EP - 1359 PB - Springer Science + Business Media CY - Dordrecht AN - OPUS4-19794 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Matthies, Klaus A1 - Erhard, Anton A1 - Ernst, h. A1 - Hübschen, G. A1 - Just, Tilman A1 - Völz, Uwe A1 - Wessels, J. A1 - Boehm, Rainer A1 - Gebhardt, W. A1 - Mrasek, Heinz A1 - Neumann, Eberhard A1 - Redmer, Bernhard A1 - Schmitz, V. A1 - Thomas, Hans-Martin A1 - Walte, F. T1 - Ultraschallprüfung von austenitischen Werkstoffen PY - 2009 SN - 978-3-87155-988-4 IS - 1. Aufl. SP - 1 EP - 464 PB - DVS-Verl. CY - Berlin AN - OPUS4-19897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kus, J. A1 - Kaufhold, S. A1 - Klosa, D. A1 - Jianwei, M. A1 - Schmidt, Martin A1 - Suhendra, Suhendra T1 - Coal fire geothermometer: Controlling the extent and temperature field of underground coal fire zones T2 - 2nd International conference on coal fire research (ICCFR2) CY - Berlin, Germany DA - 2010-05-19 KW - Coal fires KW - Coal petrography KW - Coal mineralogy PY - 2010 SN - 978-3-86012-397-3 IS - Part 2 - Geosciences SP - 75 EP - 85 AN - OPUS4-21459 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Fischer, C. A1 - Wu, J. A1 - Meyer, U. A1 - Kong, B. A1 - Schmidt, Martin A1 - Wuttke, M. A1 - Drebenstedt, C. A1 - Barth, Uli A1 - Rüter, H. T1 - Eight years of successful bilateral cooperation: Milestones of sino-german research T2 - 2nd International conference on coal fire research (ICCFR2) CY - Berlin, Germany DA - 2010-05-19 KW - Underground coal fires KW - Sino-german cooperation PY - 2010 SN - 978-3-86012-397-3 IS - Introduction SP - 3 EP - 18 AN - OPUS4-21460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - García, O. A1 - Rz-Maribona, I. A1 - Gardei, André A1 - Riedl, Martin A1 - Vanhellemont, Y. A1 - Santarelli, M.L. A1 - Strupi Suput, J. T1 - Comparative study of the variation or the hydric properties and aspect of natural stone and brick after the application of 4 types of anti-graffiti N2 - In this article a comparative study of the behaviour of different commercial anti-graffiti on natural stone and brick is presented. 8 different European substrates were selected and 4 commercial anti-graffiti of different chemical nature were applied on these substrates. The variations of their hydric properties and aspect (colour and gloss) with regard to the untreated substrates were later studied in the laboratory. The results obtained permitted to assess the suitability of 4 of the main types of chemical formulations employed to be used as anti-graffiti. This study concludes that the sacrificial anti-graffiti with polymeric paraffins in its composition presents the lowest reductions of the hydric properties of the studied substrates, being also the variations in colour the least perceptible. KW - Graffiti KW - Sandstone KW - Limestone KW - Natural stone KW - Brick KW - Anti-graffiti KW - Porous substrates KW - Surface treatments KW - Anti-graffiti coatings KW - Hydric properties KW - Colour KW - Gloss PY - 2010 DO - https://doi.org/10.3989/mc.2010.45507 SN - 0465-2746 N1 - Sprachen: Spanisch/Englisch - Languages: Spanish/English VL - 60 IS - 297 SP - 1 EP - 14 CY - Madrid AN - OPUS4-21087 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schoßig, Jörg A1 - Schmidt, Martin A1 - Krause, Ulrich A1 - Steinbach, J. T1 - Beurteilung des Selbstentzündungsverhaltens brennbarer Stäube mit Hilfe adiabatischer Warmlagerung T2 - 10. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Deutschland DA - 2010-11-04 KW - Anlagensicherheit KW - Umweltschutz KW - Sicherheitstechnik KW - Explosionsschutz PY - 2010 SN - 978-3-89746-119-2 SP - 1 EP - 7(?) CY - Frankfurt/M. AN - OPUS4-22621 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schoßig, Jörg A1 - Schmidt, Martin A1 - Krause, Ulrich A1 - Steinbach, J. T1 - Validierung von formalkinetischen Größen aus der adiabaten Warmlagerung T2 - 9. Fachtagung "Anlagen-, Arbeits- und Umweltsicherheit" CY - Köthen, Deutschland DA - 2008-11-06 KW - Anlagensicherheit KW - Umweltschutz KW - Sicherheitstechnik KW - Explosionsschutz PY - 2008 SN - 978-3-89746-099-7 SP - 1 EP - 3 PB - VDI, Hallescher Bezirksverein CY - Halle AN - OPUS4-18427 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Langenberg, K. J. A1 - Marklein, R. A1 - Mayer, K. A1 - Krylow, T. A1 - Ampha, P. A1 - Streicher, Doreen A1 - Krause, Martin ED - Pinto, I. M. T1 - Wavefield inversion in nondestructive testing T2 - Workshop/Minisymposium on "Electromagnetics in a Complex World: Challenges and Perspectives" CY - Benevento, Italy DA - 2003-02-20 PY - 2003 SN - 3-540-20235-8 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics IS - 96 SP - 1 EP - 10(?) PB - Springer CY - Berlin AN - OPUS4-2357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bär, S. A1 - Huber, G. A1 - Gonzalo, J. A1 - Perea, A. A1 - Munz, Martin T1 - Pulsed laser deposition of EU - Y2O3 thin films on (0001) alpha-Al2O3 N2 - This paper focuses on the preparation and characterization of crystalline thin films of rare-earth-doped sesquioxides (Y2O3, Lu2O3) grown by pulsed laser deposition on single-crystal (0001) sapphire substrates. X-ray diffraction measurements show that the films with thicknesses between 1 nm and 500 nm were highly textured along the 111 direction. Using Rutherford backscattering analysis, the correct stoichiometric composition of the films was established. The emission and excitation spectra of europium-doped films with a thickness 100 nm look similar to those of the corresponding crystalline bulk material, whereas films with a thickness 20 nm show a completely different emission behavior. KW - Pulsed laser deposition KW - Integrated optical devices KW - X-ray diffraction KW - Atomic force microscopy KW - Luminescence PY - 2004 UR - http://www.sciencedirect.com/science/journal/0926860X DO - https://doi.org/10.1007/s00339-004-3029-8 SN - 0947-8396 VL - 80 IS - 2 SP - 209 EP - 216 PB - Springer CY - Berlin AN - OPUS4-5990 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wondraczek, L. A1 - Reinsch, Stefan A1 - Gaber, Martin A1 - Deubener, J. A1 - Müller, Ralf A1 - Komatsu, T. T1 - Nano-crystalline germanate glass-ceramics T2 - 78. Glastechnische Tagung CY - Nürnberg, Deutschland DA - 2004-06-07 PY - 2004 SP - 37 EP - 40 PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-6953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lohrer, Christian A1 - Schmidt, Martin A1 - Malow, Marcus A1 - Krause, Ulrich A1 - Steinbach, J. T1 - Einfluss von Feuchte und Konvektionsströmung auf das Selbstentzündungsverhalten von Feststoffschüttungen KW - Selbstentzündung KW - Konvektion KW - Feuchte PY - 2005 DO - https://doi.org/10.1002/cite.200590078 SN - 0009-286X SN - 1522-2640 VL - 77 IS - 8 SP - 1141 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-10847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Dilz, K. A1 - Pohl, J. A1 - Rühe, S. A1 - Thomas, Hans-Martin A1 - Casperson, Ralf T1 - Online-Schweißnahterkennung von Schienenprüfzügen mittels Wirbelstromverfahren N2 - Zur Detektion von Schweißnähten an verlegten Schienen gehört deren Identifikation und Lokalisation. Die Aufgabe, Schweißnähte derart zu detektieren, stellt sich bei der Prüfung eines Gleisnetzes auf Schädigungen, aber auch unabhängig davon. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2003 CY - Mainz, Deutschland DA - 26.05.2003 PY - 2003 UR - http://www.ndt.net/article/dgzfp03/papers/v07/v07.htm SN - 3-931381-47-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 83-CD SP - 1 EP - 4 PB - DGZfP CY - Berlin AN - OPUS4-3491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stadthaus, Meinhard A1 - Thomas, Hans-Martin A1 - Migoun, N.P. A1 - Gnusin, A.B. A1 - Baugatz, J. A1 - König, W. T1 - Sensitivity of penetrant and magnetic particle testing - Performance testing of detection media for penetrant and magnetic particle testing (PT and MT) N2 - Die Empfindlichkeit von Eindring- und Magnetpulverprüfungen (PT, MT) hängt unter anderem von der Eignung und der Qualität der Prüfmittel ab (für PT bezeichnet als Eindringsystem). Die Ermittlung der Empfindlichkeit erfolgt an Kontrollkörpern mit natürlichen und künstlichen Inhomogenitäten durch Ermittlung der Anzeigenerkennbarkeit als Maß für die Eignung. Die europäischen Normen spezifizieren die Anforderungen an die Prüfmittel für Typen-, Chargen- und Betriebsprüfungen nach pr EN ISO 3452-2 für PT und EN ISO 9934-2 für MT. Dieser Beitrag beschreibt die Ermittlung der Empfindlichkeit von Prüfmitteln sowie deren Qualifizierung bei der Typenprüfung. Die vorgeschlagenen Verfahren wurden durch experimentelle Untersuchungen validiert, bei denen ein Bildverarbeitungssystem zur Ermittlung der Anzeigenerkennbarkeit verwendet wurde. Im Hinblick auf die Qualifizierung der Prüfmittel wird die Zuverlässigkeit der Verfahren diskutiert. PY - 2004 DO - https://doi.org/10.3139/120.100591 SN - 0025-5300 VL - 46 IS - 6 SP - 320 EP - 326 PB - Carl Hanser Verlag CY - München AN - OPUS4-3574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann, Martin A1 - Bender, Josef A1 - Plewinsky, Bodo A1 - Hieronymus, Hartmut A1 - Steinbach, J. T1 - Influence of Obstacles on Surface Detonations T2 - 2nd Internet Conference on Process Safety CY - --- DA - 2000-03-20 PY - 2000 AN - OPUS4-2125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kautek, Wolfgang A1 - Hertwig, Andreas A1 - Martin, Sven A1 - Krüger, Jörg A1 - Lenzner, Matthias A1 - Spielmann, C. A1 - Lenner, M. A1 - Bunte, J. A1 - Puester, T. A1 - Burmester, T. A1 - Fiedler, A. A1 - Heberer, E. A1 - Brose, M. A1 - Stingl, A. A1 - Kiehl, P. A1 - Hönigsmann, H. A1 - Trautinger, F. A1 - Grabner, G. T1 - Safety in Femtosecond Laser Technology - Recent Results of a European Research Project (406) T2 - International Laser Safety Conference 2003 ; ILSC 2003 CY - Jacksonville, FL, USA DA - 2003-03-10 PY - 2003 SN - 0-912035-38-2 SP - 1(?) EP - 10(?) PB - Laser Institute of America CY - Orlando, Fla. AN - OPUS4-2259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Krause, Martin A1 - Wiggenhauser, Herbert A1 - Krieger, J. T1 - Materialtechnische Untersuchung beim Abbruch der Talbrücke Haiger - Durchführung von Ultraschall- und Impakt-Echo-Messungen PY - 2002 SN - 0943-9293 IS - 38 SP - 1 EP - 111 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-2217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Horn, J. A1 - Dohle, H. A1 - Gersonde, Martin T1 - Schutzsalzverteilung in mechanisch vorbehandelten Fichtenmasten nach Kesseldrucktränkung PY - 1977 SN - 0018-3768 VL - 35 SP - 67 EP - 73 PB - Springer CY - Berlin AN - OPUS4-8725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hasenstab, Andreas A1 - Krause, Martin A1 - Lutz, J. A1 - Hillemeier, B. A1 - Rieck, C. T1 - Niederfrequente Ultraschall-Echo-Verfahren und Bohrwiderstandsmessung zur Untersuchung von Holzbauteilen T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - ZfP an Holzbauteilen KW - Fehlstellen KW - Minderdicken KW - Ultraschallecho-Experimente an Probekörpern KW - Ultraschall-Echo KW - Fäulnis KW - Bauwesen PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 11(?) PB - DGZfP CY - Berlin AN - OPUS4-11960 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bunte, J. A1 - Barcikowski, S. A1 - Burmester, T. A1 - Püster, T. A1 - Hertwig, Andreas A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Martin, Sven A1 - Spielmann, C. A1 - Lenner, M. A1 - Brose, M. T1 - Sicherer Umgang mit Ultrakurzpuls-Lasern, Teil 1: Primäre Gefährdungen PY - 2005 SN - 0945-8875 IS - 2 SP - 6 EP - 11 PB - Magazin-Verl. CY - Bad Nenndorf AN - OPUS4-11001 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bunte, J. A1 - Barcikowski, S. A1 - Burmester, T. A1 - Püster, T. A1 - Hertwig, Andreas A1 - Kautek, Wolfgang A1 - Krüger, Jörg A1 - Martin, Sven A1 - Spielmann, C. A1 - Lenner, M. A1 - Brose, M. T1 - Sicherer Umgang mit Ultrakurzpuls-Lasern, Teil 2: Sekundäre Gefährdungen PY - 2005 SN - 0945-8875 IS - 4 SP - 13 EP - 18 PB - Magazin-Verl. CY - Bad Nenndorf AN - OPUS4-11002 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Baytekin, H. Tarik A1 - Oran, Umut A1 - Theisen, J. A1 - Schmidt, Martin A1 - Unger, Wolfgang ED - Weckenmann, A. T1 - Validierte Messverfahren für die nichtgeometrische Größe Hydrophilie - Anwendung in der Mikrofluidik T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Deutschland DA - 2010-10-06 PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 163 EP - 172 PB - Shaker Verlag GmbH AN - OPUS4-24827 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Everard, C.D. A1 - Finnan, J. A1 - McDonnell, K.P. A1 - Schmidt, Martin T1 - Evaluation of self-heating in Miscanthus x giganteus energy crop clamps and the implications for harvesting time N2 - Miscanthus x giganteus energy crop grown in Ireland was harvested on 21st of February and 28th of March 2012 to examine the effects of harvesting time on self-heating during storage of Miscanthus chips in clamps (98 m³) under weather sheltered conditions. There was a relatively large difference in moisture content, of 21.4%, between Miscanthus crop harvested in February and March (41.6 and 20.2%, respectively). Temperature evolution over a storage period of up to 125 days was monitored at different heights and distances from the centre within the clamps. Maximum temperature in the February constructed clamp reached 69 °C compared to 28 °C in the March constructed clamp. Microbial activity was monitored via carbon dioxide and oxygen gas measurements. The high moisture clamp showed higher microbial activity and a volume yield loss of 4.3% due to decomposition in the top section of the clamp. Quality indices post-storage were also assessed. Calorific values from Miscanthus sampled 1 m below the top surface were similar after storage for both February and March constructed clamps, i.e. 18.52 and 18.70 MJ kg-1, respectively. A reliable assessment of self-heating in Miscanthus chip clamps has important consequences for both self-ignition risk and biomass quality. KW - Self-heating KW - Miscanthus x giganteus KW - Biomass storage KW - Self-ignition KW - Biomass quality PY - 2013 DO - https://doi.org/10.1016/j.energy.2013.06.022 SN - 0360-5442 VL - 58 SP - 350 EP - 356 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-29054 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lenke, Karoline A1 - Schmidt, R. A1 - Märtin, J. A1 - Hoffmann, G. A1 - Cherif, C. T1 - Simulation of the yarn transportation dynamics in a warp knitting machine N2 - To date, in the textile manufacturing process of warp knitting, trouble-shooting and process optimization mainly rely on empirical knowledge and experiments. This factor limits the achievable increase in productivity and quality. On the other hand, using simulations, different phenomena that affect the quality of the knitted fabric and the knitting process can be clarified in the run-up of the experiments. Consequently, an increase in quality and flexibility can be reached with reduced experimental effort. This paper presents a process simulation of the warp thread dynamics in the thread feeding system of a warp knitting machine. For this purpose, a continuum model of the warp thread that includes the spatial dynamics of the thread and the axial transport movement has been developed. KW - Simulation of yarn transportation KW - Yarn transportation model KW - Warp knitting machine KW - Continuum model KW - Process optimization KW - Knitting PY - 2013 DO - https://doi.org/10.1177/0040517512470197 SN - 0040-5175 N1 - Geburtsname von Lenke, Karoline: Metzkes, K. - Birth name of Lenke, Karoline: Metzkes, K. VL - 83 IS - 12 SP - 1251 EP - 1262 PB - Sage Publ. CY - London AN - OPUS4-28381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stadthaus, Meinhard A1 - Thomas, Hans-Martin A1 - Baugatz, J. A1 - König, W. A1 - Migoun, N. A1 - Gnusin, A. T1 - Performance testing of detection media for magnetic particle and penetrant testing following the European standards T2 - Congrès COFREND 2001 CY - Reims, France DA - 2001-04-24 PY - 2001 SP - 1(?) EP - 6(?) PB - COFREND CY - Paris AN - OPUS4-1123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hieronymus, Hartmut A1 - Hofmann, Martin A1 - Bender, Josef A1 - Henschen, Philipp A1 - Wendler, Reinhold A1 - Plewinsky, Bodo A1 - Steinbach, J. T1 - Characterization of surface explosions PY - 2001 SN - 0208-4198 VL - 21 IS - 2 SP - 117 EP - 125 PB - Wydawn. Naukowe PWN CY - Warszawa AN - OPUS4-1213 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stadthaus, Meinhard A1 - Thomas, Hans-Martin A1 - König, W. A1 - Baugatz, J. A1 - Migoun, N. A1 - Gnusin, A. T1 - Ermittlung der Eignung von Prüfmitteln für die Eindring- und Magnetpulverprüfung nach dem europäischen Normwerk T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2001 CY - Berlin, Deutschland DA - 2001-05-21 PY - 2001 UR - http://www.ndt.net/article/dgzfp01/papers/p39/p39.htm N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 75-CD PB - DGZfP CY - Berlin AN - OPUS4-1302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hieronymus, Hartmut A1 - Henschen, Philipp A1 - Hofmann, Martin A1 - Bender, Josef A1 - Wendler, Reinhold A1 - Plewinsky, Bodo A1 - Steinbach, J. ED - Pasman, H. T1 - Hazards of surface explosions T2 - 10th International Conference: Loss prevention and safety promotion in the process industries ; 620th Event of the European Federation of Chemical Engineering CY - Stockholm, Sweden DA - 2001-06-19 PY - 2001 SN - 0-444-50699-3 N1 - Serientitel: EFCE event – Series title: EFCE event IS - 620 SP - 897 EP - 908 PB - Elsevier CY - Amsterdam AN - OPUS4-1156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Hans-Martin A1 - Stadthaus, Meinhard A1 - Baugatz, J. A1 - König, W. A1 - Migoun, N. P. A1 - Prokhorenko, P. P. A1 - Gnusin, A. B. T1 - Reproducibility Problem for the Procedure of Type Testing of Liquid Penetrants N2 - Apparently that the type testing procedure should be conducted under the conditions ensuring reproducibility of its outcomes. We investigated various factors effecting upon the reproducibility. To obtain quantitative characteristics of indication’s visibility the image-processing hard-and software were used. It was established that there are two main groups of these factors. The first depends on the differences between various test panels, which are used for type testing. The second one concerns the reproducibility of some stages of penetrant testing procedure (excess penetrant removing and developer application). The recommendations to increase the reproducibility of type testing are developed and illustrated experimentally. The determination of penetrant system sensitivity as a part of type testing should be conducted ensuring reproducibility of the result. We investigated some factors effecting the reproducibility. To obtain quantitative characteristics of indication’s visibility, an image processing system was used [1]. We used 3 different sets of reference blocks (rb1, rb2, rb3) corresponding to type 1 of EN ISO 3452-3 [2]. Two fluorescent penetrants with different sensitivities and the same wet solvent developer were used. It was established that the reproducibility of type testing is influenced by mainly two principal factors. First there are the differences between reference blocks. Second one concerns the reproducibility of penetrant testing procedure, especially excess penetrant removal and developer application. According to EN ISO 3452-3 a reference block for determination of sensitivity level of fluorescent penetrants consists of a set of three nickel-chrome plated panels with 10, 20 and 30 µm plating thickness. Transverse cracks are made in each panel by stretching the panels in the longitudinal direction and width to depth ratio of the cracks should be approximately 1/20. Each panel presents a certain sensitivity level, which is characterised by the level of visibility of the indication. The highest level 3 corresponds to the panel with 10 µm thickness plating. Each panel is cut longitudinally (perpendicular to the crack) so that 2 sheets (panels A and B) with nearly the same cracks will be produced. These panels A and B of a reference block are used for relative evaluation, for example to compare sensitivities of two penetrants. It is considered that the application of the same penetrant to both panels with subsequent adequate development results in the same visibility of the indications on these panels. Quantitative correlations between the abilities of the reference blocks used for determining of the sensitivity were obtained in our investigations. We used the relations between the measured values of light-fluxes from the indications of similar comparing areas on two panels. These indications correspond to certain cracks’ parts of the same total length on both comparing areas. The relations of the steps between the panel are responsible for the definition of the sensitivity groups. From our investigations it follows that the steps of the different sets are different. Besides it was established that the indication‘s visibility for the same penetrant applied on different reference blocks might have a considerable difference depending on the penetrant sensitivity: the higher penetrant’ sensitivity, the smaller is such a difference between the steps 30/20 and 20/10. For example, for rb3 the relations 30/20 and 20/10 for lower sensitive penetrant (I1) reached factor 3 comparing with factor 2 for higher sensitive penetrant (I2). Some results of the comparison between the 3 sets (rb1, rb2, rb3) investigations are summarised in Table 1 with rb1 as a reference. T2 - 8th ECNDT CY - Barcelona, Spain DA - 2002-06-17 PY - 2002 UR - http://www.ndt.net/article/ecndt02/199/199.htm VL - 8 SP - 1(?) EP - 5(?) PB - European Federation for Non-Destructive Testing CY - Barcelona AN - OPUS4-1396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krause, Martin A1 - Wiggenhauser, Herbert A1 - Krieger, J. T1 - NDE of a Post Tensioned Concrete Bridge Girder Using Ultrasonic Pulse Echo and Impact Echo T2 - 5th Structural Materials Technology NDT Conference CY - Cincinnati, OH, USA DA - 2002-09-10 PY - 2002 SN - 1-571-17094-4 VL - 5 SP - 386 EP - 395 PB - American Society for Nondestructive Testing CY - Columbus, Ohio AN - OPUS4-1978 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zoega, A. A1 - Krause, Martin A1 - Kurz, J. A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Boßmann, N. T1 - Ultraschalluntersuchungen zur Rissdetektion an Spannbetonschwellen N2 - Im deutschen Eisenbahnnetz sind ca. 80 Millionen Spannbetonschwellen verbaut. Analog zu anderen Bauwerken werden Wpannbetonschwellen regelmäßig visuell inspiziert. Die Rissbildung ist bei diesen Inspektionen ein Kriterium für die Schädigung einer Spannbetonschwelle. Durch Rissbildung kann es passieren, dass Betonschwellen ihre Nutzungsdauer nicht erreichen. KW - ZfPBau KW - Spannbeton PY - 2017 VL - März 2017 IS - Ernst & Sohn Special 2017 SP - 20 EP - 22 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-48112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Emamverdi, Farnaz A1 - Yin, Huajie A1 - Smales, Glen Jacob A1 - Harrison, W. J. A1 - Budd, P. M. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Polymers of intrinsic microporosity - Molecular mobility and physical aging revisited by dielectric spectroscopy and X‑ray scattering N2 - Polymers of intrinsic microporosity (PIMs) are promising candidates for the active layer in gas separation membranes due to their high permeability and reasonable permselectivity. These appealing properties originate from a microporous structure as a result of inefficient segment packing in the condensed state due to a combination of a ladder-like rigid backbone and sites of contortion. However, this class of polymers suffers from a significant decrease in the permeability with time due to physical aging, whereby typically, the permselectivity increases. The initial microporous structures approach a denser state via local rearrangements, leading to the reduction of the permeability. Hence, a detailed characterization of the molecular mobility in such materials can provide valuable information on physical aging. In this work, the dielectric behavior of PIM-1 films and their behavior upon heating (aging) were revisited by isothermal frequency scans during different heating/cooling cycles over a broad temperature range between 133 and 523 K (−140 to 250 °C). In addition, the obtained results were compared with data of samples that were annealed at ambient temperatures over different time scales. Multiple dielectric processes were observed: several relaxation processes due to local fluctuations and a Maxwell−Wagner−Sillars polarization effect related to the microporosity. The temperature dependence of the rates of all processes follows the Arrhenius law where the estimated activation energy depends on the nature of the process. The influence of the thermal history (aging) on the processes is discussed in detail. KW - Polymers of intrinsic microporosity PY - 2022 DO - https://doi.org/10.1021/acs.macromol.2c00934 VL - 55 SP - 7340 EP - 7350 PB - American Chemical Society CY - Washington, DC AN - OPUS4-55485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas A1 - Goering, Harald A1 - Böhning, Martin A1 - Fritz, Andreas A1 - Rübner, J. T1 - Structure Analysis of Polymeric Nanomaterials by Relaxation Spectroscopy T2 - Polydays 2002 CY - Berlin, Germany DA - 2002-09-30 PY - 2002 SP - 1(?) AN - OPUS4-2044 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Krentel, Daniel A1 - Kluge, Martin A1 - Kohlhoff, Harald A1 - Lilienthal, A. J. T1 - Gas Tomography Up In The Air! N2 - In this paper, we present an autonomous aerial robot to reconstruct tomographic 2D slices of gas plumes in outdoor environments. Our platform, the so-called Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS) combines a lightweight Tunable Diode Laser Absorption Spectroscopy (TDLAS) sensor with a 3-axis aerial stabilization gimbal for aiming on a versatile octocopter. The TDLAS sensor provides integral gas concentration measurements but no information regarding the distance traveled by the laser diode's beam or the distribution of the gas along the optical path. We complemented the set-up with a laser rangefinder and apply principles of Computed Tomography (CT) to create a model of the spatial gas distribution from these integral concentration measurements. To allow for a rudimentary ground truth evaluation of the applied gas tomography algorithm, we set up a unique outdoor test environment based on two 3D ultrasonic anemometers and a distributed array of 10 infrared gas transmitters. We present first results showing the 2D plume reconstruction capabilities of the system under realistic conditions. T2 - IEEE Sensors 2018 CY - New Delhi, India DA - 28.10.2018 KW - Aerial robot KW - TDLAS KW - Gas tomography KW - Plume PY - 2018 SN - 978-1-5386-4707-3 SP - 396 EP - 398 PB - IEEE AN - OPUS4-46477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krause, Martin A1 - Dérobert, X. A1 - Hugenschmidt, J. A1 - Moczko, A. A1 - Niederleithinger, Ernst A1 - Taffe, Alexander ED - L. Binda, ED - M. di Prisco, ED - R. Felicetti, T1 - Benchmark for thickness measurement of concrete elements T2 - 1st International RILEM Conference, on Site Assessment of Concrete, Masonry and Timber Structures (SACoMaTiS 2008) CY - Varenna, Italy DA - 2008-09-01 KW - Thickness measurement KW - Radar KW - Ultrasonic Echo KW - Impact-Echo and Low Strain Techniques PY - 2008 SN - 978-2-35158-062-2 VL - 1 IS - PRO 59 SP - 357 EP - 366 PB - RILEM Publications AN - OPUS4-18030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bornemann-Pfeiffer, Martin A1 - Meyer, Klas A1 - Lademann, J. A1 - Kraume, M. A1 - Maiwald, Michael T1 - Contributions towards variable temperature shielding for compact NMR instruments N2 - The application of compact NMR instruments to hot flowing samples or exothermically reacting mixtures is limited by the temperature sensitivity of permanent magnets. Typically, such temperature effects directly influence the achievable magnetic field homogeneity and hence measurement quality. The internal-temperature control loop of the magnet and instruments is not designed for such temperature compensation. Passive insulation is restricted by the small dimensions within the magnet borehole. Here, we present a design approach for active heat shielding with the aim of variable temperature control of NMR samples for benchtop NMR instruments using a compressed airstream which is variable in flow and temperature. Based on the system identification and surface temperature measurements through thermography, a model predictive control was set up to minimise any disturbance effect on the permanent magnet from the probe or sample temperature. This methodology will facilitate the application of variable-temperature shielding and, therefore, extend the application of compact NMR instruments to flowing sample temperatures that differ from the magnet temperature. KW - Benchtop NMR KW - Continuous Processes KW - Inline Analytics KW - Model Predictive Control KW - Process Analytical Tecnology KW - Temperature Control PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579219 DO - https://doi.org/10.1002/mrc.5379 SN - 1097-458X SP - 1 EP - 10 PB - John Wiley & Sons Ltd. AN - OPUS4-57921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Anker, Andy S. A1 - Aspuru-Guzik, Alán A1 - Ben Mahmoud, Chiheb A1 - Bennett, Sophie A1 - Briling, Ksenia R. A1 - Changiarath, Arya A1 - Chong, Sanggyu A1 - Collins, Christopher M. A1 - Cooper, Andrew I. A1 - Crusius, Daniel A1 - Darmawan, Kevion K. A1 - Das, Basita A1 - David, Nicholas A1 - Day, Graeme M. A1 - Deringer, Volker L. A1 - Duarte, Fernanda A1 - Eardley-Brunt, Annabel A1 - Evans, Matthew L. A1 - Evans, Rob A1 - Fairlamb, Ian A1 - Franklin, Barnabas A. A1 - Frey, Jeremy A1 - Ganose, Alex M. A1 - Goulding, Mark A1 - Hafizi, Roohollah A1 - Hakkennes, Matthijs A1 - Hickey, Niamh A1 - James, Gillian A1 - Jelfs, Kim E. A1 - Kalikadien, Adarsh V. A1 - Kapil, Venkat A1 - Koczor-Benda, Zsuzsanna A1 - Krammer, Ferdinand A1 - Kulik, Heather J. A1 - Kumar, Vishank A1 - Kuttner, Christian A1 - Lam, Erwin A1 - Lou, Yuchen A1 - Mante, Eltjo A1 - Martin, Jennie A1 - Mroz, Austin M. A1 - Nematiaram, Tahereh A1 - Pare, Charles W. P. A1 - Patra, Sarbani A1 - Proudfoot, James A1 - Ruscic, Branko A1 - Ryder, Matthew R. A1 - Sakaushi, Ken A1 - Saßmannshausen, Jörg A1 - Savoie, Brett M. A1 - Schneider, Nadine A1 - Schwaller, Philippe A1 - Skjelstad, Bastian Bjerkem A1 - Sun, Wenhao A1 - Szczypiński, Filip T. A1 - Torrisi, Steven A1 - Ueltzen, Katharina A1 - Vishnoi, Shubham A1 - Walsh, Aron A1 - Wang, Xinwei A1 - Wilson, Chloe A1 - Wu, Ruiqi A1 - Zeitler, Jakob T1 - Discovering structure–property correlations: General discussion N2 - This article is a discussion of the paper "Web-BO: Towards increased accessibility of Bayesian optimisation (BO) for chemistry" by Austin M. Mroz, Piotr N. Toka, Ehecatl Antonio del Río Chanona and Kim E. Jelfs (Faraday discussions, 2025, 256, 221-234). KW - Materials design KW - Machine learning KW - Automation KW - Materials discovery PY - 2025 DO - https://doi.org/10.1039/d4fd90062f SN - 1359-6640 SN - 1364-5498 VL - 256 IS - Themed collection: Data-driven discovery in the chemical sciences SP - 373 EP - 412 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-62208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, D. A1 - Konnertz, Nora A1 - Böhning, Martin A1 - Schmidt, J. A1 - Thomas, A. T1 - Light-switchable polymers of intrinsic microporosity N2 - The interest in (micro)porous systems is greater than ever before with microporous polymers finding application in areas such as gas storage/separation and catalysis. In contrast to the vast majority of publications on microporous polymers seeking ever higher values for surface area or uptake capacity for a particular gas, this work presents a means to render a microporous system responsive to electromagnetic stimuli. The incorporation of a diarylethene (DAE) derivative in the backbone of a polymer of intrinsic microporosity (PIM) produces a microporous system that exhibits photochromism as proven by UV–vis absorption and NMR studies. In the resulting DAE-PIM, surface area is not a fixed unalterable property but can be influenced by the external and nondestructive stimulus light in a reversible manner. Furthermore, in combination with Matrimid, free-standing membranes can be produced that display light-switchable diffusivity and permeability for carbon dioxide and oxygen. In this way, material scientists are offered the potential to employ only one system that can assume several states with different properties for each. KW - Gaspermeation KW - Diffusion KW - Polymer intrinsischer Mikroporosität KW - UV-VIS PY - 2016 DO - https://doi.org/10.1021/acs.chemmater.6b02619 SN - 0897-4756 VL - 28 IS - 23 SP - 8523 EP - 8529 PB - ACS CY - Whashington,DC AN - OPUS4-38735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krause, Martin A1 - Bärmann, R. A1 - Frielinghaus, R. A1 - Kreschmar, F. A1 - Krogge, O. A1 - Langenberg, K. A1 - Maierhofer, Christiane A1 - Müller, W. A1 - Neisecke, J. A1 - Schickert, M. A1 - Schmitz, V. A1 - Wiggenhauser, Herbert A1 - Wollbold, F. ED - Schickert, G. T1 - Comparison of pulse-echo-methods for testing concrete T2 - International Symposium Non-Destructive Testing in Civil Engineering (NDT-CE) CY - Berlin, Germany DA - 1995-09-26 KW - Beton KW - Radar KW - Aufprallecho KW - Ultraschall KW - Prüfung PY - 1995 SN - 3-931381-02-1 N1 - Serientitel: BB / DGZfP – Series title: BB / DGZfP SP - 281 EP - 295 PB - DGZfP, Dt. Ges. für Zerstörungsfreie Prüfung e.V. CY - Berlin AN - OPUS4-593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wiggenhauser, Herbert A1 - Krause, Martin A1 - Krieger, J. ED - Medlock, R. T1 - Tests and assessments of NDT methods for concrete bridges N2 - A research project is described involving a comparison of different non-destructive test methods for concrete bridges. A cooperative test series was started with the aim to compare and evaluate the performance and benefits of the latest technical developments in this field. For this purpose test specimens with localized defects were produced. Different modifications of radar, ultrasonic-echo and impact-echo methods were investigated. Including two- and three- dimensional reconstruction models. The experiments were accompanied by numerical simulation of the propagation of sound waves and microwaves. The results showed that the radar and the ultrasonic methods were efficient tools to locate the tendon ducts accurately if the reinforcing bars were not to narrowly spaced. The ultrasonic imaging methods were capable of identifying injection and compaction faults in a blind test. The good performance of the impact-echo method with regard to locating tendon ducts which was claimed in several publications could not be validated in the present investigations. The simulation models provided valuable information on how to improve the experimental test program and its evaluation. T2 - Structural materials technology III CY - San Antonio, TX, USA DA - 1998-03-31 KW - Non-destructive testing in civil engineering KW - concrete bridges KW - tendons KW - ducts KW - injection faults KW - compaction faults KW - round robin test KW - ultrasonic testing KW - pulse radar KW - impact-echo KW - reconstruction calculation KW - synthetic aperture focusing technique (SAFT) KW - magnetic stray field KW - ruptures in prestressing reinforcement PY - 1999 SN - 0-8194-2849-3 DO - https://doi.org/10.1117/12.300098 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series VL - 3400 SP - 258 EP - 269 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kluge, Martin A1 - Ferrero, Fabio A1 - Schröder, Volkmar A1 - Acikalin, Hatice Aydan A1 - Steinbach, J. T1 - Modellazione del processo di autoaccensione del TFE KW - Convezione naturale (free convention) KW - Trasporto reattivo (reactive flow) KW - Reazione in fase gas (gas reaction) KW - Autoignizione (self-ignition) PY - 2011 SN - 0390-2358 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 6 SP - 84 EP - 90 PB - ERIS CY - Milan AN - OPUS4-24094 LA - ita AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dengel, Jörg A1 - Wendler, Reinhold A1 - Denzer, Wolfgang A1 - Buchholz, Joachim A1 - Kluge, Martin A1 - Steinbach, J. A1 - Plewinsky, Bodo A1 - Hieronymus, Hartmut T1 - Explosions Near the Surface of Organic Liquids KW - Heterogeneous explosions KW - Detonation KW - Deflagration KW - Explosion ranges PY - 2005 SN - 0957-5820 SN - 1744-3598 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 83 IS - B5 SP - 452 EP - 458 PB - Elsevier CY - Amsterdam AN - OPUS4-11176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kluge, Martin A1 - Krause, Heike A1 - Schröder, Volkmar A1 - Acikalin, Hatice Aydan A1 - Steinbach, J. T1 - Study of a self heating process of tetrafluoroethylene by the exothermic dimerization reaction to octafluorocyclobutane T2 - COMSOL Conference CY - Hannover, Germany DA - 2008-11-04 KW - Self heating KW - Free convection KW - Reactive flow KW - Gas reaction PY - 2008 SN - 978-09766792-8-8 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 1 EP - 7 AN - OPUS4-18611 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chan, George C.-Y. A1 - Hieftje, Gary M. A1 - Omenetto, Nicoló A1 - Axner, Ove A1 - Bengtson, Arne A1 - Bings, Nicolas H. A1 - Blades, Michael W. A1 - Bogaerts, Annemie A1 - Bolshov, Mikhail A. A1 - Broekaert, José A.C. A1 - Chan, WingTat A1 - Costa-Fernández, José M. A1 - Crouch, Stanley R. A1 - De Giacomo, Alessandro A1 - D’Ulivo, Alessandro A1 - Engelhard, Carsten A1 - Falk, Heinz A1 - Farnsworth, Paul B. A1 - Florek, Stefan A1 - Gamez, Gerardo A1 - Gornushkin, Igor B. A1 - Günther, Detlef A1 - Hahn, David W. A1 - Hang, Wei A1 - Hoffmann, Volker A1 - Jakubowski, Norbert A1 - Karanassios, Vassili A1 - Koppenaal, David W. A1 - Kenneth Marcus, R. A1 - Noll, Reinhard A1 - Olesik, John W. A1 - Palleschi, Vincenzo A1 - Panne, Ulrich A1 - Pisonero, Jorge A1 - Ray, Steven J. A1 - Resano, Martín A1 - Russo, Richard E. A1 - Scheeline, Alexander A1 - Smith, Benjamin W. A1 - Sturgeon, Ralph E. A1 - Todolí, José-Luis A1 - Tognoni, Elisabetta A1 - Vanhaecke, Frank A1 - Webb, Michael R. A1 - Winefordner, James D. A1 - Yang, Lu A1 - Yu, Jin A1 - Zhang, Zhanxia T1 - Landmark Publications in Analytical Atomic Spectrometry: Fundamentals and Instrumentation Development N2 - The almost-two-centuries history of spectrochemical analysis has generated a body of literature so vast that it has become nearly intractable for experts, much less for those wishing to enter the field. Authoritative, focused reviews help to address this problem but become so granular that the overall directions of the field are lost. This broader perspective can be provided partially by general overviews but then the thinking, experimental details, theoretical underpinnings and instrumental innovations of the original work must be sacrificed. In the present compilation, this dilemma is overcome by assembling the most impactful publications in the area of analytical atomic spectrometry. Each entry was proposed by at least one current expert in the field and supported by a narrative that justifies its inclusion. The entries were then assembled into a coherent sequence and returned to contributors for a round-robin review. KW - Analytical atomic spectrometry KW - Spectroscopy KW - Instrumental analysis PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-621588 DO - https://doi.org/10.1177/00037028241263567 SN - 1943-3530 VL - 78 SP - 1 EP - 456 PB - Sage CY - London AN - OPUS4-62158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Ferrero, Fabio A1 - Schröder, Volkmar A1 - Acikalin, Hatice Aydan A1 - Steinbach, J. T1 - Improvements in the modeling of the self ignition of tetrafluoroethylene N2 - In order to prevent incidents in the industrial production of Teflon® from Tetrafluoroethylene (TFE), the safety related aspects of the self-heating process of TFE must be taken into account. Simulations of this self heating process were performed with COMSOL Reaction Engineering Lab® and COMSOL® COMSOL Multiphysics®. A complex reaction net was employed, resulting in a model allows for a good agreement with experimentally achieved results. T2 - COMSOL Conference 2010 CY - Paris, France DA - 2010-11-17 KW - Heating KW - Free convection KW - Reactive flow KW - Gas reaction KW - Self ignition PY - 2010 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 1 EP - 7 AN - OPUS4-24174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ried, Peter A1 - Gaber, Martin A1 - Müller, Ralf A1 - Deubener, J. T1 - Hydrogen permeability of a barium-aluminoborosilicate glass - A methodical approach N2 - The H2 effusion from H2 saturated glass powders, H2 permeation through the wall of blown glass bulbs, and H2 permeation through the wall of glass capillaries were applied to evaluate the permeability of hydrogen gas in a barium-aluminoborosilicate (BABS) glass. To validate these methods, two commercial glasses (vitreous silica and borosilicate) were used as a reference. Permeation values obtained from the different experiments agreed within a factor of 3 or less. The H2 permeability of BABS glass at temperatures close to ambient was found to be at least 3 orders of magnitude below that of borosilicate and silica glasses. The powder method, which requires minimal sample preparation efforts, turned out to provide easy access to the measurement of H2 permeability of glasses down to P = 3.9 × 10- 21 mol s- 1 Pa- 1 m- 1. KW - Hydrogen gas KW - Permeability KW - Solubility KW - Diffusivity KW - Aluminoborosilicate glass PY - 2014 DO - https://doi.org/10.1016/j.jnoncrysol.2014.04.006 SN - 0022-3093 VL - 394-395 SP - 43 EP - 49 PB - North-Holland Publ. Co. CY - Amsterdam AN - OPUS4-30720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Williams, S. H. A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. A1 - Strobl, M. A1 - Douissard, P.A. A1 - Martin, T. A1 - Riesemeier, Heinrich A1 - Banhart, J. T1 - Detection system for microimaging with neutrons N2 - A new high-resolution detector setup for neutron imaging has been developed based on infinity-corrected optics with high light collection, combined with customized mounting hardware. The system can easily be installed, handled and fitted to any existing facility, avoiding the necessity of complex optical systems or further improved electronics (CCD). This is the first time optical magnification higher than 1:1 has been used with scintillator-based neutron detectors, as well as the first implementation of infinity corrected optics for neutron imaging, achieving the smallest yet reported effective pixel size of 3.375 µm. A novel transparent crystal scintillator (GGG crystal) has been implemented with neutrons for the first time to overcome limitations of traditional powder scintillators (Li6/ZnS, Gadox). The standardized procedure for resolution measurements with the Modulation Transfer Function (MTF) is summarized to facilitate comparison between instruments and facilities. Using this new detector setup, a resolution of 14.8 µm with a field of view of 6 mm × 6 mm has been achieved while maintaining reasonable count times. These advances open a wide range of new possible research applications and allow the potential for additional future developments. KW - Instrumentation for neutron sources KW - Neutron radiography KW - Neutron detectors (cold, thermal, fast neutrons) PY - 2012 DO - https://doi.org/10.1088/1748-0221/7/02/P02014 SN - 1748-0221 VL - 7 IS - P02014 SP - 1 EP - 26 PB - Inst. of Physics Publ. CY - London AN - OPUS4-26433 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kaczmarek, D. A1 - Albert, T. J. A1 - Munz, Martin A1 - Sturm, Heinz A1 - Bonse, Jörn T1 - Erratum: “Structure formation on the surface of indium phosphide irradiated by femtosecond laser pulses” [J. Appl. Phys. 97, 013538 (2005)] N2 - This erratum publishes some corrections to the article “Structure formation on the surface of indium phosphide irradiated by femtosecond laser pulses” [J. Appl. Phys. 97, 013538 (2005)]. PY - 2024 DO - https://doi.org/10.1063/5.0222903 SN - 0021-8979 SN - 1089-7550 VL - 136 IS - 4 SP - 1 EP - 2 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-60690 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sanchez-Martin, Pedro A1 - Becker, Roland A1 - Toepel, J. A1 - Gorbushina, Anna T1 - An improved test for the evaluation of hydrocarbon degradation capacities of diesel-contaminating microorganisms N2 - The development of a test to evaluate the degradation of semi-volatile fuels as diesel by microorganisms is presented. This method is based on the principles described in the CEC-L-103 Standard procedure that is exclusively meant for testing the biodegradability of non-volatile lubricants. Therefore, significant modifications involve aseptic conditions for testing specific microorganisms and conducting the test in closed vessels avoiding evaporation losses, while fuel quantification using gas chromatography-flame ionization detection (GC-FID) is retained. It is suggested that the modified procedure should enable routine application for semi-volatile hydrocarbon-based fuels. GC-FID provides additionally valuable information on the alteration of fuel component patterns during biodegradation. The procedure was successfully tested using two bacteria (Pseudomonas aeruginosa and Sphingomonas sp.) and two yeasts (Moesziomyces sp. and Candida sp.) isolated from real diesel contamination cases. All tested microorganisms caused a significant degradation of diesel fuel achieving hydrocarbon degradation percentages ranging from 23% to 35%. Specific aspects on the test modification and prospects for further modification regarding targeted investigations in the field of fuel contamination by microorganisms are briefly discussed. KW - Biofouling KW - Bacteria KW - Fungi KW - CEC-L-103 KW - GC-FID KW - Reference organisms PY - 2018 DO - https://doi.org/10.1016/j.ibiod.2018.01.009 SN - 0964-8305 VL - 129 SP - 89 EP - 94 PB - Elsevier AN - OPUS4-44524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martin-Sanchez, Pedro Maria A1 - Gebhardt, Christopher A1 - Toepel, Jörg A1 - Barry, J. A1 - Munzke, N. A1 - Günster, Jens A1 - Gorbushina, Anna T1 - Monitoring microbial soiling in photovoltaic systems: A qPCR-based approach N2 - Soiling of photovoltaic (PV) systems compromises their performance causing a significant power loss and demanding periodical cleaning actions. This phenomenon raises great concerns in the solar energy field, thus leading to notable research efforts over the last decades. Soiling is caused by a dual action of dust deposition and biofouling. However, surprisingly, the microbiological contribution to PV soiling is often overlooked or underestimated. In this study, a variety of qPCR-based methods have been developed to quantify the microbial load of fungi, bacteria and phototrophs on PV panels. These protocols were evaluated by comparison with culturedependent methods, and were implemented with real solar plants for two years. The results show that the developed molecular methods are highly sensitive and reliable to monitor the microbial component of the soiling. Fungal biomass was clearly dominant in all analysed PV modules, while bacteria and phototrophs showed much lower abundance. Light microscopy and qPCR results revealed that melanised microcolonial fungi and phototrophs are the main biofilm-forming microorganisms on the studied solar panels. In particular, the fungal qPCR protocol is proposed as a useful tool for monitoring of PV soiling, and investigating the microbial contribution to specific soiling cases. KW - Solar panels KW - PV modules KW - Real-time qPCR KW - Bacteria KW - Fungi KW - Phototrophs PY - 2018 DO - https://doi.org/10.1016/j.ibiod.2017.12.008 SN - 0964-8305 VL - 129 SP - 13 EP - 22 PB - Elsevier Science AN - OPUS4-43892 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -