TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike T1 - Wie beeinflussen nicht-atmosphärische Bedingungen das Deflagrationsverhalten? N2 - Zur Bestimmung der Deflagrationsfähigkeit von energiereichen Stoffen/ Gemischen wurde zuletzt ein Vier-Liter-Autoklav vorgeschlagen, der im Vergleich zu den derzeit gängigen Prüfmethoden eine Reihe von Vorteilen bietet. In diesem Beitrag wird der Frage nachgegangen, wie nicht-atmosphärische Bedingungen das Deflagrationsverhalten beeinflussen. Zur Beantwortung dieser Frage wurden weitere Experimente im genannten Autoklaven und in einem kleineren Autoklaven durchgeführt. Im Wesentlichen lässt sich feststellen, dass der Druck im Probengefäß vor Versuchsbeginn, insbesondere reduzierter Ausgangsdruck < 1 bar Auswirkungen auf das Deflagrationsverhalten hat. Das Vorhandensein einer reinen Stickstoffatmosphäre hingegen, beeinflusst das Deflagrationsverhalten nicht. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Nicht-atmosphärische Bedingungen PY - 2015 SN - 978-3-86011-091-1 SP - P12, 1 EP - 4 AN - OPUS4-34821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosenberg, Marika A1 - Michael-Schulz, Heike A1 - Wehrstedt, Klaus-Dieter A1 - Malow, Marcus T1 - Validation of the UN test method N.5 N2 - Many substances react with water in such a way that flammable gases are formed. For transport issues this reaction may possess a considerable hazard especially if the cargo is wetted by rain or by water from other sources. In the UN Recommendations on the Transport of Dangerous Goods these kinds of problems are addressed. The UN test N.5 'Test method for substances which in contact with water emit flammable gases' corresponds to this hazard. Classification according to the test method is done by measurement of the gas evolution rate of the flammable gas by any suitable procedure. At BAM a gravimetric approach is used to measure the gas evolution rate. In this paper we present the evaluation of the apparatus by means of an absolute calibration routine utilizing a reaction where a known amount of gas is produced as well as the evaluation of important parameters influencing the gas evolution rate using different substances. It can be shown that the apparatus is capable of measuring absolute gas volumes as low as 6 mL with an acceptable error of about 17% as determined from the reaction of Mg with demineralized water. KW - UN test N.5 KW - Water reactive substance KW - Flammable gas KW - Magnesium KW - Aluminum KW - Hydrogen PY - 2014 DO - https://doi.org/10.1016/j.jlp.2014.03.008 SN - 0950-4230 SN - 1873-3352 VL - 30 SP - 282 EP - 286 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-31037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Gebauer, Marek T1 - Experimentelle und theoretische Untersuchung des Zersetzungsmechanismus deflagrationsfähiger Substanzen N2 - Dieser Beitrag beschreibt Untersuchungen zu Deflagrationen von Azodicarbonamid, welche erstmals in einem Vier-Liter-Autoklaven durchgeführt wurden. Zunächst wird die Reproduzierbarkeit der Messungen mit der neuen Apparatur überprüft. Anschließend wird ein Vergleich mit Messungen in einer offenen Apparatur hergestellt, welche zur Prüfung der Deflagrationsfähigkeit in VDI 2263-1 erläutert ist. Zur Beschreibung der deflagrativen Zersetzungen werden die Kenngrößen Induktionszeit, Deflagrationsgeschwindigkeit, maximaler Druck, maximale und mittlere Druck- und Tempe-raturanstiegsrate herangezogen. Zusätzlich werden in weiteren Versuchen die während einer Deflagration entstehende Gasmenge und die Gasentwicklungsrate bestimmt. Abschließend werden die Druck- und Gasentwicklungsraten miteinander verglichen. Aus den Arbeiten lässt sich folgern, dass der Vier-Liter-Autoklav zur Bestimmung und Beschreibung der Deflagrationsfähigkeit von Azodicarbonamid gut geeignet ist und im Vergleich zu Messungen in offenen Prüfanordnungen eine Reihe von Vorteilen bietet. T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung CY - Magdeburg, Germany DA - 26.03.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Gas- und Druckmengenmessung PY - 2015 UR - http://www.iaut.ovgu.de/iaut_media/MBE/4_+MBE+2015/Beitr%C3%A4ge+2015/Salg_Experimentelle+und+theoretische+Untersuchung+des+Zersetzungsmechanismus+deflagrationsf%E2%80%9Ehiger+Substanzen.pdf SN - 978-3-00-048960-0 SP - 1 EP - 13 AN - OPUS4-33411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Morhenn, H. ED - Pierucci, S. ED - Klemes, J.J. T1 - Investigations of deflagration in a four-litre-autoclave under atmospheric and non-atmospheric conditons N2 - A four-litre-autoclave was used to perform deflagration tests in a closed vessel. The aim was to investigate the suitability of this autoclave and to evaluate different parameters influencing the deflagration. The validation of test results showed that the autoclave is suited for the performance of deflagration tests. In comparison to tests performed in an open system according to VDI 2263-1 the results are in good agreement. In the closed vessel same characteristics as in the open test were determined. In addition, pressure rise and rate of pressure rise have been determined and used to characterise deflagrations. The influence of sample weight, tube diameter, bulk density, initial pressure and temperature was investigated. Furthermore, the emerging gas amount and the rate of gas evolution were determined and compared with pressure curves. The use of a four-litre-autoclave for performing deflagration tests offers several advantages in comparison to an open test. T2 - ICheaP12 - International conference on chemical & process engineering CY - Milan, Italy DA - 19.05.2015 KW - Deflagration KW - Closed vessel KW - Autoclave KW - Reduced pressure PY - 2015 UR - http://www.aidic.it/cet/15/43/344.pdf SN - 978-88-95608-34-1 DO - https://doi.org/10.3303/CET1543344 SN - 2283-9216 N1 - Serientitel: Chemical engineering transactions (CEt) – Series title: Chemical engineering transactions (CEt) VL - 43 SP - 2059 EP - 2064 AN - OPUS4-33414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Uhlig, S. A1 - Frost, K. A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Schmidt, Martin A1 - Zakel, S. T1 - CEQAT-DGHS interlaboratory tests for chemical safety: Validation of laboratory test methods by determining the measurement uncertainty and probability of incorrect classification including so-called “Shark profiles” N2 - Laboratory test results are of vital importance for correctly classifying and labelling chemicals as “hazardous” as defined in the UN Globally Harmonized System (GHS) / EC CLP Regulation or as “dangerous goods” as defined in the UN Recommendations on the Transport of Dangerous Goods. Interlaboratory tests play a decisive role in assessing the reliability of laboratory test results. Interlaboratory tests performed over the last 10 years have examined different laboratory test methods. After analysing the results of these interlaboratory tests, the following conclusions can be drawn: 1. There is a need for improvement and validation for all laboratory test methods examined. 2. To avoid any discrepancy concerning the classification and labelling of chemicals, the use of validated laboratory test methods should be state of the art, with the results accompanied by the measurement uncertainty and (if applicable) the probability of incorrect classification. This paper addresses the probability of correct/incorrect classification (for example, as dangerous goods) on the basis of the measurement deviation obtained from interlaboratory tests performed by the Centre for quality assurance for testing of dangerous goods and hazardous substances (CEQAT-DGHS) to validate laboratory test methods. This paper outlines typical results (e.g. so-called “Shark profiles” – the probability of incorrect classification as a function of the true value estimated from interlaboratory test data) as well as general conclusions and steps to be taken to guarantee that laboratory test results are fit for purpose and of high quality. T2 - 13th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE 2020) CY - Braunschweig, Germany DA - 27.07.2020 KW - Dangerous goods KW - Hazardous substances KW - Interlaboratory test KW - Test method KW - Validation KW - Quality assurance KW - Measurement uncertainty KW - Incorrect classification KW - Shark profile PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-515376 UR - https://oar.ptb.de/files/download/5f3e662f4c93901010006dbf DO - https://doi.org/10.7795/810.20200724 VL - 2020 SP - 50 EP - 61 PB - Open Access Repository der Physikalisch-Technischen Bundesanstalt (PTB-OAR) CY - Braunschweig AN - OPUS4-51537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - CEQAT-DGHS Interlaboratory test programme for chemical safety - status and activities N2 - Safety experts, carriers or traders must be able to rely on the validity of the method and on correct results of safety tests and assessments in the laboratory. Bundesanstalt für Materialforschung und –prüfung (BAM), Berlin and Physikalisch-Technischen Bundesanstalt (PTB), Braunschweig have extensive experience in the field of testing and assessment of physical hazards of chemicals. Interlaboratory tests on different test methods have been performed by BAM and PTB during the last 10 years. Significant differences between the results of the participating laboratories were observed in all interlaboratory test. The deviations of the test results were not caused only by laboratory faults but also by deficiencies of the test method; i.e. many of the method descriptions are too ambiguous and allow divergences for interpretation. Therefore, it is necessary to know exactly how good the method is that is used to classify dangerous goods or hazardous substances or to determine safety-relevant parameters. A key criterion is the measurement uncertainty. One can choose simple methods with large error limits, but the measurement uncer-tainties should be known and always communicated together with the test results. This would allow safety specialists to be able to assess test results correctly and make well-founded decisions, e.g. for adequate protective measures. Interlaboratory tests play a decisive role in assessing the reliability of test results. Participation in interlaboratory tests is not only a crucial element of the quality as-surance of laboratories; as such it is explicitly recommended in DIN EN ISO/IEC 17025. In addition, interlaboratory tests are also used to develop and validate test methods and can be used for the determination of the measurement uncertainty. Therefore, the BAM and PTB continue to support the further development of the interlaboratory test programme of CEQAT-DGHS (Centre for quality assurance for testing of dangerous goods and hazardous substances, www.ceqat-dghs.bam.de), established in 2007. This programme is run by BAM in collaboration with the PTB and the QuoData Gesellschaft für Qualitätsmanagement und Statistik mbH, Dresden. A new interlaboratory test for methods validation on the test method UN Test N.5 "Test method for substances which in contact with water emit flammable gases” is currently being prepared and will be carried out in 2018. Laboratories that specialise in this test are invited to participate in the interlaboratory test. Interested laboratories can check the details and register to participate in the interlaboratory test at the CEQAT-DGHS website. T2 - MEETINGS OF IGUS EOS GROUP CY - Shanghai, P.R. China DA - 09.04.2018 KW - Interlaboratory test KW - Dangereous goods KW - Hazardous substances KW - Test method KW - Validation PY - 2018 AN - OPUS4-44825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - CEQAT-DGHS Interlaboratory test programme for chemical safety - status and activities - New RR UN Test N.5 with verification apparatus - N2 - The UN Test N.5 "Test method for substances which in contact with water with flammable gases", according to the Chapter 33.5.4 of the UN Manual of Tests and Criteria is one of the tests performed at BAM and was already investigated in detail. As a conclusion from these investigations a new verification method for the verification of this gas flow measuring test apparatus for the method UN Test N.5 was developed at BAM and is presented in this presentation as well as general aspects in the development of verification procedures will be explained. The planned interlaboratory test to validate the new verification method is discussed in this presentation. T2 - IGUS EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 02.04.2025 KW - CEQAT-DGHS KW - Gas flow rate KW - Verification of test apparatuses KW - Interlaboratory tests KW - UN Test N.5 PY - 2025 AN - OPUS4-63205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Update on the revision of test method for oxidizing solids N2 - The results of the round robin test on the solid oxidiser test have already been presented at IGUS EOS. In this presentation, we will show how the findings from the round robin test can be transferred into the regulations as easily as possible. This proposal serves as a basis for a proposal that can be discussed in the ECOSOC Sub-Committee of Experts on TDG (30 June - 04 July 2025). T2 - IGUS_EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 20.04.2025 KW - Classification KW - Test method KW - Oxidizer KW - Solids PY - 2025 AN - OPUS4-63203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, G. A1 - Wehrstedt, Klaus-Dieter A1 - Malow, Marcus A1 - Budde, K. A1 - Mosler, J. T1 - Safe transport of acrylic acid in railroad tank cars. Part 1: Determination of the self-accelerating decomposition temperature N2 - Experiments according to a test specified in the UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, and numerical simulations by means of a finite element method are employed to determine the self-accelerating decomposition temperature of acrylic acid in a railroad tank car. The results demonstrate that the transport of acrylic acid in big tank cars is safe as long as some basic conditions are taken into account. KW - Acrylic acid KW - Dangerous goods KW - Finite element method KW - Railway transport KW - Self-accelerating decomposition temperature PY - 2014 DO - https://doi.org/10.1002/ceat.201300778 SN - 0930-7516 SN - 1521-4125 VL - 37 IS - 9 SP - 1460 EP - 1467 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-31298 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN Test Series H - a comparison T2 - Ad hoc EOS Meeting CY - Frankfurt am Main, Germany DA - 2014-01-28 PY - 2014 AN - OPUS4-30257 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN-Test N.5 also for toxic substances? T2 - Ad hoc EOS Meeting CY - Frankfurt am Main, Germany DA - 2014-01-28 PY - 2014 AN - OPUS4-30258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN-Test O.2: Replacement of cellulose T2 - Ad hoc EOS Meeting CY - Frankfurt am Main, Germany DA - 2014-01-28 PY - 2014 AN - OPUS4-30259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Polymerizing substances - some problems concerning classification for transport T2 - Ad hoc EOS Meeting CY - Frankfurt am Main, Germany DA - 2014-01-28 PY - 2014 AN - OPUS4-30261 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Wehrstedt, Klaus-Dieter A1 - Schuurman, P. A1 - Hoeijmakers, P.M.M. T1 - Comments on 'thermal decomposition kinetic evaluation and its thermal hazards prediction of AIBN, by S. Guo, W. Wan, C. Chen and W.H. Chen' (Journal of thermal analysis and calorimetry (2013) 113:1169-1176, DOI 10.1007/s10973-013-2993-7) N2 - We read the paper by Guo et al. [1] with interest. The authors have investigated the thermal decomposition kinetics and thermal hazards of 2,2′-azobis(isobutyronitrile), AIBN, by differential scanning calorimetry (DSC) and used the Advanced Kinetics and Technology Solutions (AKTS) software to predict the thermal stability of AIBN in ton and kg scale. The main conclusion of interest is that the self-accelerating decomposition temperature (SADT) of a 50-kg standard package is 63 °C. PY - 2014 DO - https://doi.org/10.1007/s10973-014-3897-x SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 117 IS - 3 SP - 1015 EP - 1016 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-31251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - BAM H.1 and H.4 test results on AIBN T2 - IGUS EOS Meeting CY - Nanjing, China DA - 2014-04-09 PY - 2014 AN - OPUS4-30553 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Salg, S. A1 - Schomäcker, R. T1 - Der Einfluss hohen Umgebungsdrucks auf Deflagrationen N2 - Das Deflagrationsverhalten von Feststoffen unter atmosphärischen Bedingungen wurde in der Vergangenheit eingehend untersucht. Standardmäßig wird die Deflagrationsprüfung in einem offenen System durchgeführt. Aber auch in geschlossenen Systemen ist die Deflagrationsprüfung durchführbar und sie liefert Ergebnisse, die mit den Standardmethoden vergleichbar sind. Darüber hinaus bietet die Prüfung in einem geschlossenen System den Vorteil, nicht nur die Temperatur, sondern auch den Druck messen und für die Beschreibung des Deflagrationsverlaufs heranziehen zu können. Auch für die Prüfung in geschlossenen Systemen liegt eine Reihe an experimentellen Ergebnissen vor. Von Klais wurde veröffentlicht, dass die Deflagrationsgeschwindigkeit, beschrieben anhand der Druckanstiegsrate, mit steigendem Druck ansteigt. Vor dem Hintergrund dieser experimentellen Beobachtung wurde interpretiert, dass die Steigerung der Geschwindigkeit ihre Ursache im steigenden Umgebungsdruck findet. Es wurde weiter versucht, einen funktionalen Zusammenhang zwischen Umgebungsdruck und Deflagrationsgeschwindigkeit, ausgedrückt durch die Druckanstiegsrate, herzustellen. Dabei wurde nicht beachtet, dass neben dem Umgebungsdruck noch andere Einflussfaktoren auf die Deflagrationsgeschwindigkeit gegeben sind. Wesentlich ist hierbei die für die Reaktion zur Verfügung stehende Oberfläche, die sich bei einer lokalen, punktförmigen Anzündung mit fortschreitender Reaktionszeit vergrößert. In diesem Beitrag wird der Einfluss des Umgebungsdrucks auf die Deflagrationsgeschwindigkeit systematisch untersucht. Zu diesem Zweck wurden Experimente bei verschiedenen Ausgangsdrücken bis zu 50 bar (abs) durchgeführt. Der Anfangsdruck, also der Druck der vor Beginn eines Experiments im Reaktionsraum herrscht, wurde schrittweise von einem Experiment zum nächsten erhöht. Für die Versuchsreihen wurden zwei Substanzen verwendet: Azodicarbonamid und ein Imidazolderivat. Diese unterscheiden sich in ihrem Deflagrationsverhalten und hinsichtlich der Gasmengenentwicklung. Die durchgeführten Experimente haben gezeigt, dass die Deflagrationsgeschwindigkeit mit steigendem Druck zunimmt. Sowohl die Druckanstiegsrate, als auch die lineare Ausbreitungsrate sind ein gutes Maß dafür. Zwischen den beiden Kenngrößen besteht ein linearer Zusammenhang. Für eine gegebene Geometrie lässt sich die eine Kenngröße aus der anderen berechnen. T2 - 5. Brand- und Explosionsschutztage 2017 CY - Magdeburg, Germany DA - 23.03.2017 KW - Deflagrationen KW - Geschlossenes System KW - Azodicarbonamid KW - Druckanstiegsrate KW - Deflagrationsgeschwindigkeit PY - 2017 SN - 978-3-00-056201-3 SP - 1 EP - 11 AN - OPUS4-39920 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Der Einfluss hohen Umgebungsdrucks auf Deflagrationen N2 - Das Deflagrationsverhalten von Feststoffen unter atmosphärischen Bedingungen wurde in der Vergangenheit eingehend untersucht. Standardmäßig wird die Deflagrationsprüfung in einem offenen System durchgeführt. Aber auch in geschlossenen Systemen ist die Deflagrationsprüfung durchführbar und sie liefert Ergebnisse, die mit den Standardmethoden vergleichbar sind. Darüber hinaus bietet die Prüfung in einem geschlossenen System den Vorteil, nicht nur die Temperatur, sondern auch den Druck messen und für die Beschreibung des Deflagrationsverlaufs heranziehen zu können. Auch für die Prüfung in geschlossenen Systemen liegt eine Reihe an experimentellen Ergebnissen vor. Von Klais wurde veröffentlicht, dass die Deflagrationsgeschwindigkeit, beschrieben anhand der Druckanstiegsrate, mit steigendem Druck ansteigt. Vor dem Hintergrund dieser experimentellen Beobachtung wurde interpretiert, dass die Steigerung der Geschwindigkeit ihre Ursache im steigenden Umgebungsdruck findet. Es wurde weiter versucht, einen funktionalen Zusammenhang zwischen Umgebungsdruck und Deflagrationsgeschwindigkeit, ausgedrückt durch die Druckanstiegsrate, herzustellen. Dabei wurde nicht beachtet, dass neben dem Umgebungsdruck noch andere Einflussfaktoren auf die Deflagrationsgeschwindigkeit gegeben sind. Wesentlich ist hierbei die für die Reaktion zur Verfügung stehende Oberfläche, die sich bei einer lokalen, punktförmigen Anzündung mit fortschreitender Reaktionszeit vergrößert. In diesem Beitrag wird der Einfluss des Umgebungsdrucks auf die Deflagrationsgeschwindigkeit systematisch untersucht. Zu diesem Zweck wurden Experimente bei verschiedenen Ausgangsdrücken bis zu 50 bar (abs) durchgeführt. Der Anfangsdruck, also der Druck der vor Beginn eines Experiments im Reaktionsraum herrscht, wurde schrittweise von einem Experiment zum nächsten erhöht. Für die Versuchsreihen wurden zwei Substanzen verwendet: Azodicarbonamid und ein Imidazolderivat. Diese unterscheiden sich in ihrem Deflagrationsverhalten und hinsichtlich der Gasmengenentwicklung. Die durchgeführten Experimente haben gezeigt, dass die Deflagrationsgeschwindigkeit mit steigendem Druck zunimmt. Sowohl die Druckanstiegsrate, als auch die lineare Ausbreitungsrate sind ein gutes Maß dafür. Zwischen den beiden Kenngrößen besteht ein linearer Zusammenhang. Für eine gegebene Geometrie lässt sich die eine Kenngröße aus der anderen berechnen. T2 - 5. Brand- und Explosionsschutztage CY - Magdeburg, Germany DA - 23.03.2017 KW - Deflagrationen KW - Geschlossenes System KW - Azodicarbonamid KW - Druckanstiegsrate KW - Deflagrationsgeschwindigkeit PY - 2017 AN - OPUS4-39921 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - RRT O.2/O.3 – Results of BAM N2 - During the last couple of years BAM took part in different Round Robin Tests for the determination of oxidative properties of liquid and solid substances. The obtained results from these tests are reviewed and discussed in this presentation. New findings from recent particle size distribution measurements were discussed as well. N2 - Über die letzten Jahre hat die BAM an verschiedenen Round Robin Tests zur Bestimmung der oxidativen Eigenschaften von flüssigen und festen Stoffen teilgenommen. Die Ergebnisse werden diskutiert sowie zusätzliche Messungen zur Bestimmung der Partikelgrößenverteilung der verwendeten Cellulosen vorgestellt. T2 - IGUS EOS Meeting CY - Basel, Switzerland DA - 11.04.2016 KW - O.2 Test PY - 2016 AN - OPUS4-37191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Determination and simulation of SADT for packages, IBCs and tanks N2 - Die Konzepte zur Bestimmung der SADT für verschiedene Transportgebindegrößen werden an drei Beispielen aus der Praxis erläutert. Insbesondere wird auf die Problematik der Bestimmung der SADT für große Tranportgebinde eingegangen. Verschiedene Simulationsmethoden für die Berechnung der SADT werden vorgestellt. T2 - IGUS EOS/EPP Joint Meeting CY - Basle, Switzerland DA - 13.04.2016 KW - SADT KW - Test series H KW - Test series 8 PY - 2016 AN - OPUS4-36848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Thermische Zersetzung von AIBN – Experimente und Simulationen zur Bestimmung der SADT N2 - Die thermische Zersetzung von AIBN wurde in einem Projekt mit mehreren Teilnehmern untersucht. Hierbei wurde die selbstbeschleunigende Zersetzungstemperatur (SADT) sowohl experimentell als auch auf Grundlage von Simulationsrechnungen bestimmt. Die Besonderheit bei dem Feststoff AIBN ist, dass die Zersetzung sowohl in der festen, als auch in der flüssigen Phase nach dem Schmelzen stattfindet, was bei den durchgeführten Simulationsrechnungen berücksichtigt werden musste. Die berechneten SADT-Werte stimmen mit den experimentell bestimmten sehr gut überein. T2 - 14. BAM-PTB-Kolloquium zur chemischen und physikjalischen Sicherheitstechnik CY - Berlin, Germany DA - 14.06.2016 KW - SADT KW - Reaktionskinetik KW - AIBN KW - DSC KW - UN-Test H.1 KW - UN-Test H.4 PY - 2016 AN - OPUS4-37256 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Schomäcker, R. T1 - Evaluation of deflagration behaviour using different sized autoclaves N2 - Deflagration tests were conducted with two kinds of autoclaves. Parameter studies were carried out concerning the gas atmosphere and substances used. Deflagration tests were performed in different pressure regions. Furthermore, deflagration test results of different substances were compared to the corresponding DSC results. Previous findings concerning vacuum conditions could be approved for a greater range of substances. In addition, investigations in nitrogen atmosphere were performed in order to investigate the deflagration behaviour. Experiments up to 161 bar could be utilized. An acceleration of deflagration velocity with increasing pressure was observed in a large pressure interval. T2 - 15th International Symposium of Loss Prevention and Safety Promotion CY - Freiburg, Germany DA - 05.06.2016 KW - Deflagration KW - Closed Vessel KW - Autoclave KW - Effect of Pressure PY - 2016 SN - 978-88-95608-39-6 DO - https://doi.org/10.3303/CET1648033 SN - 2283-9216 VL - 48 SP - 193 EP - 198 PB - Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-37259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Duerrstein, St. A1 - Kappler, C A1 - Neuhaus, I. A1 - Gödde, M. T1 - Model-Based Prediction of the Adiabatic Induction Period and SADT of Dicumyl Peroxide Solution and Comparison to Large-Scale Experiments Performed Using 216.5-Liter Steel Drums in the UN-Test H.1 N2 - The thermal decomposition of dicumyl peroxide dissolved in ethylbenzene has been studied in our laboratories using differential scanning calorimetry (DSC), calvet calorimetry (C80), adiabatic calorimetry, reaction calorimetry and micro calorimetry. Based on the DSC and C80 experiments a formal kinetics model has been derived, which was compared to the other applied techniques. Finally we used our model to predict the thermal response of 216.5 L steel drums to exposure to constant elevated temperatures, both using the stationary Semenov approach as well as time-resolved CFD simulations. The prediction was compared to one-to-one testing using the UN-Test H.1. The observed level of consistency between model and experiments is remarkably good. The comparison with the 216.5 L testing clearly demonstrates that reliable and conservative predictions for technically relevant scales are possible as long as a validated model is used. T2 - 15th International Symposium of Loss Prevention and Safety Promotion in the Process Industries CY - Freiburg, Germany DA - 05.06.2016 KW - Thermal decomposition KW - Self-accelerating decomposition temperature KW - Dicumyl peroxide KW - CFD simulations KW - Real scale FST PY - 2016 SN - 978-88-95608-39-6 DO - https://doi.org/10.3303/CET1648080 SN - 2283-9216 VL - 48 SP - 475 EP - 480 PB - AIDIC CY - Freiburg AN - OPUS4-37875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Wehrstedt, Klaus-Dieter A1 - Michael-Schulz, Heike A1 - Malow, Marcus A1 - Schomäcker, R. T1 - Die Deflagration von Azodicarbonamid unter verschiedenen Umgebungsbedingungen N2 - Azodicarbonamid (ADCA) ist ein bekanntermaßen deflagrationsfähiger Stoff, der in der Kunststoffindustrie als Treib- und Blähmittel eingesetzt wird. In diesem Beitrag wird die Deflagration von ADCA unter verschiedenen Bedingungen betrachtet. Es werden Ergebnisse von Experimenten in offenen und geschlossenen Systemen präsentiert. In geschlossenen Systemen wurde die Zusammensetzung der umgebenden Atmosphäre von Luft mit Umgebungsdruck über Luft mit Unter- und Überdruck hin zu Stickstoff mit Umgebungsdruck variiert. Um das Deflagrationsrisiko zu reduzieren wird eine Verarbeitung von ADCA im Vakuum vorgeschlagen. T2 - 14. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Berlin, Germany DA - 14.06.2016 KW - Deflagration KW - geschlossene Behälterprüfung PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 SP - 118 EP - 125 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-37877 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Wehrstedt, Klaus-Dieter A1 - Mishra, Kirti Bhushan A1 - Steinbach, J. T1 - Thermische Zersetzung von AIBN - Experimente und Simulationen zur Bestimmung der SADT N2 - Die thermische Zersetzung von AIBN wurde in einem Projekt mit mehreren Teilnehmern untersucht. Hierbei wurde die selbstbeschleunigende Zersetzungstemperatur SADT) sowohl experimentell als auf Grundlage von Simulationsrechnungen bestimmt. Die Besonderheit bei dem Feststoff AIBN ist, dass die Zersetzung sowohl in der festen, als auch in der flüssigen Phase nach dem Schmelzen stattfindet, was bei den durchgeführten Simulationsrechnungen berücksichtigt werden musste. Die berechneten SADT Werte stimmen mit den experimentell bestimmten sehr gut überein. T2 - 14. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Berlin, Germany DA - 14.06.2016 KW - SADT KW - Reaktionskinetik KW - AIBN KW - DSC KW - UN-Test H.1 KW - UN-Test H.4 PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 SP - 54 EP - 59 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-37878 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Wehrstedt, Klaus-Dieter A1 - Manolov, Manol T1 - Thermal decomposition of AIBN Part A: Decomposition in real scale packages and SADT determination N2 - In this paper the thermal decomposition of 2,2′-azobisisobutyronitrile (AIBN) was investigated in real scale packages of different sizes and in 500 mL Dewar vessels. Packages containing 5 kg, 20 kg and 50 kg of AIBN have been investigated according to the UN test H.1 method and the 500 mL Dewar experiments were performed according to the UN test H.4 method. The self-accelerating decomposition temperature (SADT) was determined for the different masses and for the 500 mL Dewar vessel. Additionally, DSC curves have been recorded in closed crucibles. All these experimental data are the basis of a series of forthcoming papers dealing with the simulation of the SADT for different masses using reliable kinetic data. PY - 2015 DO - https://doi.org/10.1016/j.tca.2015.06.013 SN - 0040-6031 SN - 1872-762X VL - 621 SP - 1 EP - 5 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-35010 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Michael-Schulz, Heike A1 - Malow, Marcus T1 - Use of a four-liter-autoclave for conducting deflagration tests N2 - For the determination of deflagration capability of energetic substances, the test methods according to VDI 2263-1, part 1.6 and UN-Manual, C.1- und C.2-test are used. These methods are suited to evaluate the intrinsic material property deflagration. For evaluation of deflagration behavior in closed systems, for example in production sites, an appropriate test apparatus is missing. Because of this, the BAM Federal Institute for Materials Research and Testing developed a four-liter-autoclave for conducting the deflagration test under isochoric conditions. Deflagration behavior was evaluated under different parameters e. g. pressure and temperature. On the basis of results it can be seen, that the four-liter-autoclave is suited for the determination of deflagration behavior. On the one hand, the same characteristics as in the standard test methods are obtained. On the other hand, there are additional characteristics, like pressure rise and decomposition velocity. On the basis of pressure measurement, the emerging gas volume and the rate of gas evolution, that are used to design protection measures, can be estimated. The measurements are conducted with the deflagrating substance Azodicarboxamide (ADCA). It is concluded that the four-liter-autoclave is a good alternative for conducting deflagration tests. T2 - 18th Seminar on new trends in research of energetic materials - NTREM CY - Pardubice, Czech Republic DA - 15.04.2015 KW - Deflagration KW - Azodicarboxamide KW - Closed vessel KW - Pressure rise KW - Arising gases PY - 2015 UR - http://www.ntrem.com/download/NTREM_2015_abstracts.pdf SN - 978-80-7395-891-6 SN - 978-80-7395-892-3 SP - 255 EP - 264 AN - OPUS4-33490 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Salg, Steffen A1 - Malow, Marcus A1 - Morhenn, H. T1 - Experimentelle und theoretische Untersuchung des Zersetzungsmechanismus deflagrationsfähiger Substanzen N2 - In einem Vier-Liter-Autoklaven wurden erstmals Untersuchungen zu Deflagrationen von Azodicarbonamid durchgeführt. Aus den Arbeiten lässt sich folgern, dass der Vier-Liter-Autoklav zur Bestimmung und Beschreibung der Deflagrationsfähigkeit von Azodicarbonamid gut geeignet ist und im Vergleich zu Messungen inoffenen Prüfanordnungen eine Reihe von Vorteilen bietet. KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Gas- und Druckmengenmessung PY - 2015 SN - 2191-0073 VL - 5 IS - 6 SP - 39 EP - 44 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-33491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - A new apparatus for the investigaton of deflagrations T2 - IGUS EOS meeting CY - Ottawa, Canada DA - 2015-05-06 PY - 2015 AN - OPUS4-33378 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN Test N.5 - new test results T2 - IGUS EOS meeting CY - Ottawa, Canada DA - 2015-05-06 PY - 2015 AN - OPUS4-33379 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Use of four-liter-autoclave for conducting deflagration tests T2 - New Trends in Reseach of Energetic Materials CY - Pardubice, the Czech Republic DA - 2015-04-15 PY - 2015 AN - OPUS4-33382 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Suitable diluents for the group of desensitized explosives? N2 - The question, what is a suitable diluent for the group of desensitized explosives, is adressed in this presentation. After a review of the definions from the corresponding regulations a possible testing scheme is presented and discussed. It should only be possible to test a phlegmatized explosive out of class 1 via a negative result in test series 6. The characteristics of a suitable diluent is discussed in the second part of the presentation. T2 - IGUS EOS Meeting CY - Rijswijk, The Netherlands DA - 24.04.2017 KW - Desensitized explosives KW - Test series 6 PY - 2017 AN - OPUS4-41986 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Noll, Matthias A1 - Ferrero, Fabio A1 - Naumann, Annette A1 - Malow, Marcus T1 - Entwicklung von pilzlichen und bakteriellen Lebensgemeinschaften in einer Kiefernholzhalde N2 - Das Interesse für erneuerbare Energieträger ist in den letzten Jahren stark angestiegen. Im Bereich Biomasse als erneuerbarer Energieträger wird besonders Holz ein großes Wachstum auf dem Energiesektor prognostiziert (NITSCH 2007). Die Speicherung dieser Energie erfolgt meist durch Holzhackschnitzelhalden in der Umwelt. Um ein tieferes Verständnis der in der Halde ablaufenden mikrobiologischen Prozesse erhalten zu können, wurden in einer neu aufgebauten Kiefernholzhackschnitzelhalde mit den Ausmaßen 15 m x 20 m x 6 m folgende Messungen durchgeführt: a.) Messung der Gaskonzentration von Sauerstoff, Kohlendioxid als auch der Temperaturentwicklung innerhalb der Halde; b.) Messung der Veränderung der Holzzusammensetzung innerhalb der Halde über die Zeit; c.) Charakterisierung der Veränderung der Zusammensetzung der bakteriellen als auch der pilzlichen Lebensgemeinschaften über die Zeit; d.) Charakterisierung von dominanten Vertretern der bakteriellen als auch der pilzlichen Lebensgemeinschaften. Die Ergebnisse zeigen, dass sich die Funktion und die Zusammensetzung der Lebensgemeinschaften über die Dauer der Holzhackschnitzellagerung ändern, und dass diese Änderungen nur zum Teil mit den Prozessen bei Kompostierungsanlagen vergleichbar sind. T2 - Experten Workshop "Lagerung von Holzhackschnitzeln" CY - Potsdam-Bornim, Deutschland DA - 2008-06-18 KW - Ascoymceten KW - Pseudomonas KW - Bakterien KW - Pilze KW - Temperatur KW - Pilzliche und bakterielle Lebensgemeinschaften PY - 2008 SN - 0947-7314 IS - 63 SP - 58 EP - 72 CY - Potsdam AN - OPUS4-18645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Modified Setup of 20-L-Sphere of Determination of Safety Characteristics of Nano Powders T2 - 17th CY - Tokyo, Japan DA - 2010-05-26 PY - 2010 AN - OPUS4-21364 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Center for quality assurance for testing of dangerous goods and hazardous substances - Brief information about status and activities T2 - IGUS ENERGETIC AND OXIDISING SUBSTANCES WORKING GROUP CY - Tokyo, Japan DA - 2010-05-26 PY - 2010 AN - OPUS4-21344 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Problems encountered comparing UN-Test H.2 und UN-Test H.4 results T2 - IGUS Energetic and Oxidising Substances (EOS) Working Group Meeting CY - Tokyo, Japan DA - 2010-05-26 PY - 2010 AN - OPUS4-21361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - DSC: Thermal stability of dilauroylperoxide T2 - IGUS Energetic and Oxidising Substances (EOS) Working Group Meeting CY - Tokyo, Japan DA - 2010-05-26 PY - 2010 AN - OPUS4-21362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrero, Fabio A1 - Malow, Marcus A1 - Berger, Anka A1 - Noll, Matthias T1 - Brandvermeidung bei der Lagerung von biogenen Brennstoffen am Beispiel von Kiefernholz T2 - Experten Workshop "Lagerung von Holzhackschnitzeln" CY - Potsdam-Bornim, Deutschland DA - 2008-06-18 KW - Selbstentzündung KW - Brandverhütung KW - Lagerung KW - Biomasse KW - Schüttgüter PY - 2008 SN - 0947-7314 IS - 63 SP - 32 EP - 44 CY - Potsdam AN - OPUS4-19043 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrero, Fabio A1 - Lohrer, Christian A1 - Schmidt, Bernd A1 - Noll, Matthias A1 - Malow, Marcus T1 - A mathematical model to predict the heating-up of large-scale wood piles N2 - A mathematical model to predict the heating-up in open air wood chip piles has been developed. This model includes the heat production from chemical, physical and microbial exothermal processes. In the manuscript the laboratory experiments needed to develop and validate the model are described. In addition, temperature and gas concentrations were measured in two large-scale wood piles (volumes bigger than 1000 m³), in order to provide the applicability of the model to large-scale scenarios. The predictions of the model and the large-scale experimental data showed good agreement concerning the maximum temperature reached inside an open air wood pile. Special attention has been devoted to the microbial processes, since they proved to be the most important cause of heat production in the early stages of storage. This work is intended to help in predicting and thus avoiding possible self-ignition scenarios for this type of wood storage. KW - Wood chips KW - Storage KW - Self-ignition KW - Numerical simulation KW - Large-scale piles KW - Biomass PY - 2009 DO - https://doi.org/10.1016/j.jlp.2009.02.009 SN - 0950-4230 SN - 1873-3352 VL - 22 SP - 450 EP - 459 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-19200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Evaluative comparison of two methods for sadt determination (UN H.1 and H.4) T2 - 12th Annual Symposium, Mary Kay O'Connor Process Safety Center "Beyond Regulatory Compliance: Making Safety Second Nature" Texas A&M University CY - College Station, TX, USA DA - 2009-10-27 PY - 2009 AN - OPUS4-20232 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Wehrstedt, Klaus-Dieter T1 - Evaluative comparison of two methods for SADT determination (UN H.1 and H.4) N2 - We present our results on the comparsion of two methods for the SADT determination. Both methods, UN test H.1 and UN test H.4 are recommended by the international transport regulations from the UN. But during the last years the applicability of the UN test H.4 has been questioned for solid substances. Therefore, three organic peroxidesand one self-reactive substance have been investigated in 5 kg and 20 kg packages as well as in the UN test H.4 in a 500 mL dewar vessel. The SADT values determined with the different methods match. The UN test H.4 seems to be well suited also for solid substances at least for 20 kg or 60 L. T2 - 12th Annual symposium, Mary Kay O´Connor Process Safety Center "Beyond regulatory compliance: making safety second nature" CY - College Station, Texas, USA DA - 2009-10-27 KW - Thermal explosion KW - Organic peroxides KW - Self-reactive substances KW - SADT KW - Heat accumulation storage test KW - US SADT test PY - 2009 SN - 978-0-692-00459-3 IS - Chapter "Explosion - I" SP - 230 EP - 237 AN - OPUS4-20277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Sind DSC Experimente geeignet, um die thermische Stabilität von Dilauroylperoxid vorherzusagen? T2 - 10. Fachtagung "Anlagen-, Arbeits- und Umweltsicherheit" CY - Köthen, Germany DA - 2010-11-04 PY - 2010 AN - OPUS4-22369 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schmidt, Martin A1 - Ferrero, Fabio A1 - Malow, Marcus A1 - Krause, Ulrich T1 - Vermeidung der Brandentstehung bei der Lagerung von Biomasse T2 - VDI-Fachtagung - Sichere Handhabung brennbarer Stäube CY - Nürnberg, Deutschland DA - 2010-11-16 KW - Selbstentzündung KW - Biomasse KW - Numerische Simulation KW - Brandvermeidung PY - 2010 SN - 978-3-18-092096-2 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 2096 SP - 87 EP - 98 AN - OPUS4-22501 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Wehrstedt, Klaus-Dieter T1 - Evaluative comparison of two methods for SADT determination (UN H.1 and H.4) N2 - We present our results on the comparison of two methods for the SADT determination. Both methods, UN test H.1 and UN test H.4 are recommended by the international transport regulations from the UN. But during the last years the applicability of the UN test H.4 has been questioned for solid substances. Therefore, three organic peroxides and one self-reactive substance have been investigated in 5 kg and 20 kg packages as well as in the UN test H.4 in a 500 mL Dewar vessel. The SADT values determined with the different methods match. The UN test H.4 seems to be well suited for solid organic peroxides and self-reactive substances of at least 20 kg or 60 L. KW - Thermal explosion KW - Organic peroxides KW - Self-reactive substances KW - SADT KW - Heat accumulation storage test KW - US SADT test PY - 2010 DO - https://doi.org/10.1016/j.jlp.2010.06.014 SN - 0950-4230 SN - 1873-3352 VL - 23 IS - 6 SP - 740 EP - 744 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-22640 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, Klaus-Dieter A1 - Malow, Marcus T1 - Letter to the Editor - Comments on the "Letter to the editor" by M.-L. You and C.-M. Shu (Journal of Thermal Analysis and Calorimetry, 2010;100:367-369) as response to the "Letter to the editor" by M. Malow and K.-D. Wehrstedt (Journal of Thermal Analysis and Calorimetry, 2009;98:885-886) KW - Dilauroyl peroxide KW - Oxygen balance KW - DSC KW - Simulation KW - SADT PY - 2011 DO - https://doi.org/10.1007/s10973-010-1122-0 SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 103 IS - 1 SP - 409 EP - 410 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-23210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Validation of the UN test method N.5 T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23643 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Simulated 50 kg package for SADT testing T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Problems with formulations containing sodium carbonate peroxyhyrate T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN test series H - current project of BAM T2 - IGUS Energetic and Oxidising Substances (EOS) Working Group Meeting CY - Stockholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17471 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ferrero, Fabio A1 - Noll, Matthias A1 - Schmidt, Bernd A1 - Malow, Marcus A1 - Schmidt, Martin T1 - Experimentelle und numerische Analyse des Selbstentzündungsverhalten von Holzhalden T2 - 9. Fachtagung "Anlagen-, Arbeits- und Umweltsicherheit" CY - Köthen, Deutschland DA - 2008-11-06 KW - Brandvermeidung KW - Biomasse KW - Lagerung KW - Schüttgüter KW - Selbstentzündung PY - 2008 SN - 978-3-89746-099-7 SP - 1 EP - 21 PB - VDI, Hallescher Bezirksverein CY - Halle AN - OPUS4-18305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - UN test H.1 - some new experimental results T2 - IGUS Energetic and Oxidising Substances (EOS) Working Group Meeting CY - Saint Petersburg, Russia DA - 2009-06-10 PY - 2009 AN - OPUS4-19500 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Wehrstedt, Klaus-Dieter T1 - Comments on "Thermal explosion and runaway reaction simulation of lauroyl peroxide by DSC tests, by Mei-Li You, Ming-Yang Liu, Sheng-Hung Wu, Jen-Hao Chi, Chi-Min Shu" (Journal of Thermal Analysis and Calorimetry, 2009;96:777-782) KW - Lauroyl peroxide KW - Thermal analysis KW - DSC KW - Kinetics PY - 2009 DO - https://doi.org/10.1007/s10973-009-0534-1 SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 98 IS - 3 SP - 885 EP - 886 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-20791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Malow, Marcus A1 - Ferrero, Fabio A1 - Noll, Matthias ED - Mahammadzadeh, M. ED - Biebeler, H. ED - Bardt, H. T1 - Brandvermeidung bei der Lagerung von Biomasse KW - Brandvermeidung KW - Selbstentzündung KW - Biomasse PY - 2009 SN - 978-3-602-14847-9 IS - Kap. 13 SP - 107 EP - 114 CY - Köln AN - OPUS4-20811 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -