TY - GEN A1 - Tzschichholz, Grit A1 - Steinborn, Gabriele A1 - Keller, M.H. A1 - Manara, J. T1 - Porous nano-composite materials with low emittance for reducing energy consumption T2 - Nanofair 2008 - New Ideas for Industry / 6th International Nanotechnology Symposium CY - Dresden, Germany DA - 2008-03-11 PY - 2008 SN - 978-3-18-092027-6 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 2027 SP - 231 EP - 235 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-17746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Tina A1 - Stark, T. A1 - Arduini, M. A1 - Manara, J. A1 - Altenburg, Simon T1 - Knowing the spectral directional emissivity of 316L and AlSi10Mg PBF-LB/M surfaces: Gamechanger for quantitative in situ monitoring N2 - For a deep process understanding of the laser powder bed fusion process (PBF-LB/M), recording of the occurring surface temperatures is of utmost interest and would help to pave the way for reliable process monitoring and quality assurance. A notable number of approaches for in-process monitoring of the PBF-LB/M process focus on the monitoring of thermal process signatures. However, due to the elaborate calibration effort and the lack of knowledge about the occurring spectral directional emissivity, only a few approaches attempt to measure real temperatures. In this study, to gain initial insights into occurring in the PBF-LB/M process, measurements on PBF-LB/M specimens and metal powder specimens were performed for higher temperatures up to T = 1290 °C by means of the emissivity measurement apparatus (EMMA) of the Center for Applied Energy Research (CAE, Wuerzburg, Germany). Also, measurements at ambient temperatures were performed with a suitable measurement setup. Two different materials—stainless steel 316L and aluminum AlSi10Mg—were examined. The investigated wavelength λ ranges from the visible range (λ-VIS= 0.40–0.75 µm) up to the infrared, λ = 20 µm. The influence of the following factors were investigated: azimuth angle φ, specimen temperature TS, surface texture as for PBF-LB/M surfaces with different scan angles α, and powder surfaces with different layer thicknesses t. T2 - Rapid.Tech 3D 2024 CY - Erfurt, Germany DA - 14.05.2024 KW - PBF-LB/M KW - In situ monitoring KW - Emissivity KW - Additive manufacturing PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601471 DO - https://doi.org/10.1007/s40964-024-00665-2 SN - 2363-9520 SP - 1 EP - 10 PB - Springer CY - Cham, Switzerland AN - OPUS4-60147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steinborn, Gabriele A1 - Tzschichholz, Grit A1 - Günster, Jens A1 - Keller, M.H. A1 - Manara, J. T1 - Porous TiO2-Y2O3 ceramics with specific infrared-optical properties N2 - The infrared-optical properties and particularly the emissivity of sintered ceramics depend on the material's bulk properties and structural properties such as porosity, pore size distribution and pore diameter. The infrared-optical properties can be varied across a wide range by specifically selecting the material's bulk and structural properties. A major concern of the present study is the development of a ceramic coating material with a total emissivity below 0.2 at a temperature of 800 °C. For this purpose, various samples of a TiO2-Y2O3 (TY) ceramic composite were produced with different properties. On variation in the Y2O3 content from 5 to 60 wt%, the porosity of the ceramic composites varies from 3 % to 47 % with the mean pore diameter lying in a range from 0.3 µm to 1.7 µm. The addition of graphitic pore builders increases the porosity up to 60 % and the mean pore diameter to a maximum of 15 µm. By optimizing the total porosity and the pore size of the TY ceramics, a total emissivity as low as 0.17 at 800 °C could be achieved. KW - Oxide ceramic KW - Porosity KW - Mean pore diameter KW - Infrared optical properties KW - Emissivity PY - 2011 DO - https://doi.org/10.4416/JCST2011-00011 SN - 2190-9385 VL - 2 IS - 3 SP - 183 EP - 190 PB - Göller CY - Baden-Baden AN - OPUS4-24551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -