TY - JOUR A1 - Puerto, D. A1 - Siegel, J. A1 - Gawelda, W. A1 - Galvan-Sosa, M. A1 - Ehrentraut, L. A1 - Bonse, Jörn A1 - Solis, J. T1 - Dynamics of plasma formation, relaxation, and topography modification induced by femtosecond laser pulses in crystalline and amorphous dielectrics N2 - We have studied plasma formation and relaxation dynamics along with the corresponding topography modifications in fused silica and sapphire induced by single femtosecond laser pulses (800 nm and 120 fs). These materials, representative of high bandgap amorphous and crystalline dielectrics, respectively, require nonlinear mechanisms to absorb the laser light. The study employed a femtosecond time-resolved microscopy technique that allows obtaining reflectivity and transmission images of the material surface at well-defined temporal delays after the arrival of the pump pulse which excites the dielectric material. The transient evolution of the free-electron plasma formed can be followed by combining the time-resolved optical data with a Drude model to estimate transient electron densities and skin depths. The temporal evolution of the optical properties is very similar in both materials within the first few hundred picoseconds, including the formation of a high reflectivity ring at about 7 ps. In contrast, at longer delays (100 ps–20 ns) the behavior of both materials differs significantly, revealing a longer lasting ablation process in sapphire. Moreover, transient images of sapphire show a concentric ring pattern surrounding the ablation crater, which is not observed in fused silica. We attribute this phenomenon to optical diffraction at a transient elevation of the ejected molten material at the crater border. On the other hand, the final topography of the ablation crater is radically different for each material. While in fused silica a relatively smooth crater with two distinct regimes is observed, sapphire shows much steeper crater walls, surrounded by a weak depression along with cracks in the material surface. These differences are explained in terms of the most relevant thermal and mechanical properties of the material. Despite these differences the maximum crater depth is comparable in both material at the highest fluences used (16J/cm2). The evolution of the crater depth as a function of fluence can be described taking into account the individual bandgap of each material. KW - Femtosecond laser ablation KW - Plasma formation KW - Time-resolved microscopy KW - Dielectrics KW - Fused silica KW - Sapphire KW - Scanning force microscopy KW - Reflectivity measurements KW - Transmission measurements KW - Drude model PY - 2010 DO - https://doi.org/10.1364/JOSAB.27.001065 SN - 0740-3224 SN - 1520-8540 VL - 27 IS - 5 SP - 1065 EP - 1076 PB - Optical Society of America CY - Washington, DC AN - OPUS4-21167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Silveira, D. A1 - Oliveira, C. A1 - Varum, H. A1 - Ioannou, I. A1 - Miccoli, Lorenzo A1 - Tarque, N. A1 - Parisi, F. A1 - Fenu, L. A1 - Solis, M. A1 - Rodriguez-Mariscal, J. D. ED - Varum, H. ED - Parisi, F. ED - Tarque, N. ED - Silveira, D. T1 - Mechanical Characterization of Adobe Bricks N2 - The mechanical characterization of adobe bricks is an important first step in the study of the behaviour of adobe masonry. For this reason, in the last decades, different authors have conducted research on the mechanical behaviour of adobes from various regions of the world. Despite the importance of mechanical characterization, there are still only a few standards and normative documents with clear indications for the mechanical testing of earthen materials and, in general, These indications are not thorough and vary among different countries. Consequently, authors tend to adopt different types of test specimens and procedures in their experimental work, thus obtaining results that are not directly comparable. The fact that the materials and procedures traditionally used are also not standardized,varying greatly from region to region, also contributes to the difficulty of comparing results from different studies. This chapter presents a review of the indications provided by codes, standards and other technical recommendations for the mechanical testing of adobe bricks, as well as a detailed review of procedures adopted, and results obtained by different authors regarding the mechanical characterization of traditional adobe bricks. This chapter focuses, in particular, on the behaviour of adobe bricks when subjected to simple compression. It provides an overview of the existing knowledge and identifies needs for future research and development. KW - Adobe KW - Adobe masonry KW - Mechanical behaviour KW - Test procedures KW - Standards PY - 2021 SN - 978-3-030-74736-7 DO - https://doi.org/10.1007/978-3-030-74737-4 SN - 2194-9832 VL - 20 SP - 35 EP - 54 PB - Springer Nature Switzerland AG AN - OPUS4-54170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Oliveira, C. A1 - Silveira, D. A1 - Varum, H. A1 - Parisi, F. A1 - Miccoli, Lorenzo A1 - Solis, M. A1 - Rodriguez-Mariscal, J. D. A1 - Tarque, N. ED - Varum, H. ED - Parisi, F. ED - Tarque, N. ED - Silveira, D. T1 - Mechanical Characterization of Adobe Masonry N2 - The characterization of the mechanical properties and behaviour of adobe masonry is fundamental for the understanding of the structural behaviour of adobe constructions. Thus, in the last decades, experimental studies focused on this topic have been carried out by different authors. Many of the existing experimental works, however, were carried out aiming to support broader studies focused on the seismic behaviour of adobe constructions and are not very detailed. Moreover, authors tend to adopt different procedures in their experimental work, since there are few indications in existing standards for testing adobe masonry. The wide variety in materials used, both for the adobes and mortars, further complicates this work, making it difficult to compare results obtained in different studies. This chapter provides an overview of the indications given by standards and other technical recommendations for the mechanical testing of adobe masonry. It presents a review of existing research on the mechanical behaviour of adobe masonry, addressing studies that focus on: (i) compression behaviour, (ii) shear behaviour, (iii) joint shear behaviour. It provides a global analysis of the existing knowledge, suggesting improvements for normative documents and identifying future Research needs. KW - Adobe masonry KW - Mechanical behaviour KW - Experimental tests KW - Standards PY - 2021 SN - 978-3-030-74736-7 DO - https://doi.org/10.1007/978-3-030-74737-4_4 SN - 2194-9832 VL - 20 SP - 55 EP - 92 PB - Springer Nature Switzerland AG AN - OPUS4-54171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Bachelier, G. A1 - Wiggins, S. M. A1 - Siegel, J. A1 - Solis, J. A1 - Krüger, Jörg A1 - Sturm, Heinz T1 - Femtosecond laser ablation of indium phosphide in air: dynamical, structural and morphological evolution N2 - The irradiation of single-crystalline indium phosphide (c-InP) by Ti:sapphire femtosecond laser pulses (130 fs, 800 nm) in air is studied by means of in-situ time resolved reflectivity measurements [fs-time-resolved microscopy (100 fs-10 ns) and point probing analysis (ns - µs)] and by complementary ex-situ surface analytical methods (Micro Raman Spectroscopy, Scanning Force, and Optical Microscopy). The dynamics of melting, ablation, and optical breakdown as well as structural changes resulting from rapid solidification are investigated in detail. Different laser-induced surface morphologies are characterized and discussed on the basis of recent ablation and optical breakdown models. KW - Femtosecond laser ablation KW - Optical breakdown KW - Time-resolved measurements KW - Semiconductor KW - Indium phosphide PY - 2010 SN - 1454-4164 VL - 12 IS - 3 SP - 421 EP - 426 PB - INOE & INFM CY - Bucharest AN - OPUS4-21082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -