TY - CONF A1 - Gaal, Mate A1 - Bartusch, Jürgen A1 - Schadow, Florian A1 - Beck, Uwe A1 - Daschewski, M. A1 - Kreutzbruck, M. T1 - Airborne ultrasonic systems for one-sided inspection using thermoacoustic transmitters N2 - Airborne ultrasonic inspection is performed in through transmission, where the test piece (e.g. adhesive joint or polymer-based composite plate) is placed between the transmitter and the receiver. However, many structures with difficult shapes allow only one-sided inspection. The strong reflection of the signal from the surface overshadows the signals from the inside, so that broadband pulses are required. Thermoacoustic transmission, where the thermal energy of an electrically heated electrode is transformed into the acoustic energy of an ultrasonic wave, opens the possibility to excite broadband pulses and thus to inspect objects with one-sided access. We present various thermoacoustic transducers consisting of an electrically conductive film on a solid substrate. The first type of transducer is a transmitter with an indium-tin-oxide electrode on a glass substrate combined with a laser Doppler vibrometer as a receiver. The second type of transducer combines thermoacoustic transmission and piezoelectric reception, having a titanium electrode as a transmitter deposited onto charged cellular polypropylene serving as a piezoelectric receiver. Using a focusing thermoacoustic transmitter and a separate cellular polypropylene receiver, a through-transmission inspection of a 4 mm thick CFRP test piece with inserts as small as 1 mm was performed. The same emitter and a laser vibrometer as a receiver were used for a one-sided inspection of a Plexiglas block with a cross hole at 15 mm depth. A twin probe consisting of a thermoacoustic transmitter on a cellular polypropylene receiver was applied to a profile measurement on a step wedge with flat bottom holes. The smallest detected diameter of a flat bottom hole was 1 mm. Sound pressure level above 140dB was achieved with each of these transmitters. Thermoacoustic transmitters enable a step towards one-sided air-coupled ultrasonic inspection. T2 - IEEE International Ultrasonics Symposium CY - Tours, France DA - 18.09.2016 KW - Airborne KW - Air-coupled KW - Ultrasonic transducer KW - Thermoacoustic KW - Ferroelectret PY - 2016 SN - 978-1-4673-9897-8 SN - 1948-5719 SP - (online publication) 1 EP - 4 AN - OPUS4-37620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahammer, M. A1 - Myrach, Philipp A1 - Maierhofer, Christiane A1 - Busse, G. A1 - Kreutzbruck, M. T1 - Auflösungsgrenzen der Lockin-Thermografie zur Prüfung von Faserkunststoffverbunden N2 - Aktive Thermografie mit Lockin-Anregung ist ein zerstörungsfreies Prüfverfahren, das insbesondere auch die Prüfung von kohlenstofffaserverstärkten Kunststoffen ermöglicht. Um eine Standardisierung dieses Verfahrens voranzubringen, wurden im Rahmen eines Forschungsprojektes umfangreiche Untersuchungen zur Validierung des Verfahrens durchgeführt. Für die Anregungsmethoden optisch und Ultraschall wurden die wichtigsten Parameter systematisch untersucht. Auf der Auswertungsseite ist dies z.B. der Einfluss der spektralen Empfindlichkeit verschiedener Kamerasysteme. Für die Anregungen sind unter anderem die Einflüsse von Anregungsenergie und Ultraschallfrequenz untersucht worden. Auch Materialparameter, wie der Lagenaufbau bei CFK-Probekörpern, beeinflussen die Ergebnisse stark. T2 - 24. Stuttgarter Kunststoffkolloquium CY - Stuttgart, Germany DA - 25.02.2015 KW - Zerstörungsfreie Prüfung KW - Lockin-Thermografie KW - Faserkunststoffverbunde KW - Non-destructive testing KW - Lockin-Thermography KW - Fibre-reinforced plastics PY - 2015 SP - 1 EP - 7 AN - OPUS4-32876 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc A1 - Schilling, M. T1 - Numerical method of active thermography for the reconstruction of back wall geometry N2 - The paper presents numerical methods to detect and classify defects and inhomogeneities by means of active thermography. The objective is to determine the wall thickness of structure elements with an inaccessible back wall, for example, of pipes or Containers. As test specimens we used approximately 2 cm thick PVC samples with spatial variations in the back wall geometry. Flash lamps provided the heating. To know the thickness of the wall, we used two inversion methods and compared the results achieved. One is an iterative echo defect shape method and already tested on Steel test specimens with good reconstruction results. The second one is the Levenberg-Marquardt method, applied here to thermographic data for non-destructive testing. Since data capturing using active thermography and the presented numerical methods can easily be automated, the combination of these two procedures is a promising approach providing a broad area of application. T2 - 6th Workshop 'NDT in progress' CY - Prague, Czech Republic DA - 10.10.2011 KW - Impulse-thermography KW - Inversion KW - Levenberg-Marquardt method KW - Echo defect shape KW - Defect shape reconstruction PY - 2011 SN - 978-80-214-4339-6 IS - Chapter 8 SP - 245 EP - 252 AN - OPUS4-25144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schenk, Gottfried A1 - Brackrock, Daniel A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Deutsch, W.A.K. A1 - Joswig, M. A1 - Maxam, K. A1 - Schuster, V. ED - Thompson, D.O. ED - Chimenti, D.E. T1 - Ultrasonic inspection system for automated round-bar-testing based on phased array technique N2 - Within a know-how transfer project funded by the government conventional ultrasonic technique was replaced by phased array technique for automated round-bar testing. Instead of applying a great number of conventional probes to achieve acceptable volume coverage we used curved linear arrays. The benefits of phased array technique such as programmable skew angles, beamforming and beam positions, led not only to a significant decrease in inspection time, but also the number of probes could be substantially reduced . Finally, the testing parameters for a large range of bar-diameters could be adapted by software control instead of time-consuming mechanical replacement. The probe-design was carried out by a proprietary modelling program. Both the theoretical calculations as well as the latter experimental verifications revealed significant advantages of curved arrays versus the planar types. A radial oriented probe offers perfect adaption to the cylindrical shape of the specimen allowing wide variations of the sound field. Thus beam direction, beam size and beam position could be optimized with respect to a minimum of inspection cycles, as inspections have to be executed in-line during the production. A number of laboratory tests were carried out on special test components. In order to achieve an optimal performance of the reference rod we implemented three different types of reference reflectors: (i) flat-bottom-holes with diameters of 0.8 mm and 1.2 mm, (ii) side-drilled-holes with a diameter of 0.7 mm for the detection of volumetric flaws, and (iii) notches with a depth of 0.2 mm and 0.5 mm for the detection of surfaceoriented defects. All laboratory tests were carried out with the COMPAS-XXL inspection system, a proprietary development of BAM. T2 - 36th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Kingston, RI, USA DA - 2009-07-26 KW - Ultrasonic testing KW - Phased array KW - Round bar testing PY - 2010 SN - 978-0-7354-0748-0 SN - 0743-0760 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 29 SP - 1 EP - 7 CY - Melville, NY AN - OPUS4-21817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thiel, Erik A1 - Kreutzbruck, M. A1 - Ziegler, Mathias T1 - Laser-projected photothermal thermography using thermal wave field interference for subsurface defect characterization N2 - The coherent superposition of two anti-phased thermal wave fields creates a zone of destructive interference which is extremely sensitive to the presence of defects without any reference measurements. Combining a high power laser with a spatial light modulator allows modulating phase and amplitude of an illuminated surface that induces spatially and temporally controlled thermal wave fields. The position and depth of defects are reconstructed from analysis of the Amplitude and Phase of the resulting photothermal signal. The proposed concept is experimentally validated and supported by numerical modeling. KW - Thermal waves KW - Active thermography KW - DMD KW - Spatial light modulator KW - Subsurface defects PY - 2016 UR - http://scitation.aip.org/search?value1=laser+projected+photothermal&option1=all&option912=resultCategory&value912=ResearchPublicationContent&operator8=AND&option8=pub_serialIdent&value8=aip%2Fjournal%2Fapl&qs=true U6 - https://doi.org/10.1063/1.4963139 SN - 0003-6951 VL - 109 IS - 12 SP - 123504-1 EP - 123504-4 PB - AIP Publishing CY - Melville, New York AN - OPUS4-37590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Bartusch, Jürgen A1 - Dohse, Elmar A1 - Kreutzbruck, Marc A1 - Amos, J. M. ED - Chimenti, D.E. ED - Bond, L.J. ED - Thompson, D.O. T1 - Air-coupled ultrasonic testing of metal adhesively bonded joints using cellular polypropylene transducers N2 - Adhesively bonded aluminum components have been widely used in the aerospace industry for weight-efficient and damage-tolerant structures. Automated squirter jet immersion ultrasonic testing is a common inspection technique to assure the bond integrity of large, contoured assemblies. However, squirter jet inspection presents several limitations in scanning speed, related to water splash noise over protruding stiffeners and splash interference crosstalk in multi-channel inspection systems. Air-coupled ultrasonic testing has been evaluated as an alternative, possibly offering the benefits of increased throughput by enabling higher speeds, and eliminating the contamination concerns and maintenance issues of water couplant systems. Adhesive joints of multi-layer aluminum plates with artificial disbonds were inspected with novel air-coupled ultrasonic probes based on cellular polypropylene. Disbonds of various sizes were engineered in several multi-layer configurations and at various depths. Results were compared with squirter jet immersion and conventional piezoelectric transducer designs in terms of scan contrast, resolution and inspection time. T2 - 40th Annual review of progress in quantitative nondestructive evaluation CY - Baltimore, Maryland, USA DA - 21.07.2013 KW - Air-coupled KW - Ultrasonic KW - Metal bond KW - Ferroelectret PY - 2014 SN - 978-0-7354-1212-5 SN - 978-0-7354-1211-8 U6 - https://doi.org/10.1063/1.4864857 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1581 33A SP - 471 EP - 478 PB - AIP Publishing AN - OPUS4-31362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Dohse, Elmar A1 - Bartusch, Jürgen A1 - Köppe, Enrico A1 - Kreutzbruck, Marc A1 - Hillger, W. A1 - Amos, J. M. T1 - Ultrasonic testing of adhesively bonded joints using air-coupled cellular polypropylene transducers N2 - In air-coupled ultrasonic testing, the impedance mismatch between the transducer and the air is commonly being solved by adding matching layers to composite transducers. To avoid the difficult technological procedure regarding matching layers, some new piezoelectric materials have been proposed. Most promising are ferroelectrets, which are charged cellular polymers, having ferroelectric and consequently piezoelectric properties. In particular, the extreme softness of cellular polypropylene (cPP) leads to a high piezoelectric constant and to a good impedance match with the air, making matching layers redundant. Its elasticity modulus below 1 MPa causes an additional effect not observed with common piezoelectric materials: that is the electrostrictive effect, here defined as the thickness change due to the attractive force between the transducer electrodes. This effect exceeds the piezoelectric effect at excitation voltages over 1 kV. The extreme softness of cPP leads also to high flexibility, enabling easy focusing by bending the transducer. We have developed air-coupled ultrasonic transducers based on cPP. This includes the electrical matching networks for the transmitter and for the receiver. The transmitter is excited with voltages up to 2.5 kV, so that the electrostrictive effect dominates, leading to sound pressure around 145dB at the transducer surface. These transducers have been applied for testing carbon-fiber-reinforced polymer plates, adhesive joints and other composite structures. Here we report about ultrasonic transmission of two types of adhesive joints. The first one is multi-layer aluminium components with some artificial disbonds, which are common in aerospace industry, and the second one is an aluminium-steel joint with polyurethane adhesive, which is used in automotive industry. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Air-coupled KW - Ultrasonic testing KW - Ferroelectret KW - Cellular polypropylene KW - Transducer KW - Adhesive joint PY - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-317204 SN - 978-80-214-5018-9 SP - 1 EP - 8 PB - Brno University of Technology AN - OPUS4-31720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schenk, Gottfried A1 - Brackrock, Daniel A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Deutsch, W.A.K. A1 - Joswig, M. A1 - Maxam, K. A1 - Schuster, V. ED - Mazal, Pavel T1 - Ultrasonic inspection system for automated round-bar-testing based on phased array technique T2 - 5th International workshop of NDT experts - NDT in progress 2009 CY - Prague, Czech Republic DA - 2009-10-12 KW - Ultrasonic testing KW - Phased array KW - Round bar testing PY - 2009 SN - 978-80-214-3968-9 SP - 253 EP - 259 AN - OPUS4-20338 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schenk, Gottfried A1 - Brackrock, Daniel A1 - Boehm, Rainer A1 - Kreutzbruck, Marc A1 - Deutsch, W.A.K. A1 - Joswig, M. A1 - Maxam, K. A1 - Schuster, V. T1 - Untersuchungen zum Einfluss von Geometrie- und Temperaturabweichungen bei der Stangenprüfung mit Ultraschall-Gruppenstrahlertechnik N2 - Bei der automatisierten Prüfung von Stangen mit Ultraschall- Gruppenstrahlertechnik besteht grundsätzlich die Möglichkeit, Prüfkopfparameter wie Einschallwinkel, Fokustiefe und Schallbündelbreite programmgesteuert an sich verändernde Prüfbedingungen anzupassen. Zu diesen zählt die Temperatur des Koppelmediums (Wasser), die in einem Bereich von 10°C bis 50°C liegen kann, was zu unterschiedlichen Schallgeschwindigkeiten führt und den Einschallwinkel verändert. Mit der Folge, dass unter Umständen die geforderte 100%-Abdeckung des Prüfvolumens nicht mehr gewährleistet ist. Auch geometrische Abweichungen, wie sie durch die fertigungsbedingte Streuung des Prüflings gegeben sind, können Einfluss auf das Prüfergebnis nehmen. So führen Abweichungen vom idealen Geradheitszustand zu Fehlpositionierungen des Prüfkopfs, was wiederum Einfluss auf die Lage und Beschaffenheit des Schallbündels in der Stange hat. Ähnliches gilt für nicht vollkommen kreisförmig ausgebildete Stangendurchmesser, die unterschiedliche Schalleintrittsbedingungen bewirken und Abweichungen von den theoretisch ermittelten Werten zur Folge haben. Im Rahmen eines vom BMWi geförderten Forschungsvorhabens wurde der Einfluss dieser Parameter untersucht und ihre Auswirkungen für den Betrieb einer automatisierten Prüfanlage unter realen Betriebsbedingungen ermittelt. Dies betrifft vor allem den maximal möglichen Schallbündelversatz innerhalb des Arrays, der die Anzahl der erforderlichen Prüftakte bestimmt und damit die maximale Vorschubgeschwindigkeit des Prüflings. Des Weiteren werden Möglichkeiten zur programmgesteuerten Kompensation der untersuchten Temperatur- und Geometrieabweichungen durch eine flexible Anpassung der Gruppenstrahler- Prüfkopfparameter aufgezeigt. T2 - DGZfP-Jahrestagung 2010 CY - Erfurt, Deutschland DA - 2010-05-10 PY - 2010 SN - 978-3-940283-26-9 IS - DGZfP-BB 122 (Mi.4.A.1) SP - 1 EP - 8 CY - Berlin AN - OPUS4-21878 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Boehm, Rainer A1 - Kitze, Jessica A1 - Eggers, H. A1 - Böwe, M. T1 - Using UT-SAFT for analysis of stress corrosion cracking N2 - Stress corrosion cracking is a transcrystalline or intercrystalline crack formation in materials which occurs under the influence of static tensile stress or residual stress and a specific aggressive medium such as chloride containing substances. This special sort of crack formation is involved in complex crack configurations, which may only insufficiently be captured by conventional ultrasonic probes with fixed angles of incidence. Only a number of different beam angles produce sufficient reflection to reconstruct the complete defect shape from measured ultrasonic data. The SAFT algorithm, which was recently successfully used in many industrial NDT-applications, is a promising tool for the reconstruction process. In addition, the combination of phased array technique and SAFT was developed in several projects by BAM, Berlin. Investigations using phased array equipment were performed to look into crack configurations in test blocks with different surface curvatures. UT-SAFT has been used for the analysis of spark-eroded notches simulating stress corrosion cracks at the thermo sleeve weld of a nozzle. For comparison, UT-SAFT has also been applied for the analysis of real reflectors at the same position in a nozzle used in a power plant, which was repaired later on. SAFT-scans received from reconstructed ultrasonic measurement data confirm the practical usefulness of the SAFTalgorithm developed by BAM. T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components CY - Berlin, Germany DA - 2010-09-29 KW - Stress corrosion cracking KW - Real and simulated cracks KW - D-nozzle KW - Phased array technique KW - SAFT reconstruction PY - 2010 SN - 978-3-940283-30-6 IS - DGZfP-BB 125 (Th.2.B.1) SP - 1 EP - 10 CY - Berlin AN - OPUS4-23594 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pohl, Rainer A1 - Commandeur, C. A1 - Erthner, Thomas A1 - Kreutzbruck, M. A1 - Pelkner, Matthias T1 - GMR-Streufluss-Prüfsystem zur Detektion verdeckter Fehler in Feinblechen N2 - BAM und TATA Steel untersuchen gemeinsam, ob sich die Prüfung von ferritischen Feinblechen mit einer Stärke von etwa 0,2 mm während der Fertigung durch den Einsatz von GMR-Sensorik verbessern lässt. Hierzu wurde eine Vorstudie an Feinblechen mit eingebrachten Mikronuten durchgeführt. Diese Nuten variieren in ihrer Tiefe zwischen 5 μm und 60 μm und wurden verdeckt mit ZfP-angepassten GMR-Sensorarrays geprüft. Die Ergebnisse der Vorstudie zeigten, dass bei verdeckter Prüfung schon kleinste Defekte mit einer Tiefe von 10 μm - gleichbedeutend mit einer Restwanddicke von 90 % – mit einem SNR > 6 dB detektiert werden konnten, wobei der Abstand der Prüfsonde zur Oberfläche bis zu 500 μm betrug. Zudem wurden in der Vorstudie Untersuchungen zur Prüfgeschwindigkeit und Praxistauglichkeit durchgeführt. Basierend auf den hier gewonnenen Ergebnissen wird ein erster Demonstrator für eine zuverlässige Prüfung eines Teilbereiches von 50 mm des Feinbleches innerhalb einer Produktionslinie aufgebaut. Zum Einsatz kommen Prüfsonden mit jeweils 24 GMR-Sensorelementen. Hierbei wird das Ziel einer umfassenden Prüfung des Feinblechs über die gesamte Breite von 1200 mm angestrebt. Eine besondere Herausforderung stellt dabei die hohe Anzahl von mehr als 1000 Sensorelementen dar. Das hierfür entwickelte Prüfkonzept umfasst neben einer angepassten Erzeugung des Magnetfeldes die Entwicklung einer geeigneten schnellen und sicheren Elektronik für die neuen Mehrkanalprüfköpfe. Neben der Vorstellung des Prüfkonzeptes und seiner Eigenschaften vergleichen wir die erzielten Prüfergebnisse an verschiedenen Vergleichsfehlern mit denen der Vorstudie. T2 - DACH-Jahrestagung 2015 CY - Salzburg, Austria DA - 11.05.2015 KW - Streuflussprüfung KW - GMR PY - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-343354 SN - 978-3-940283-68-9 IS - DGZfP BB 152 SP - Mi.2.B.3, 1 EP - 9 AN - OPUS4-34335 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stegemann, Robert A1 - Cabeza, Sandra A1 - Lyamkin, V. A1 - Bruno, Giovanni A1 - Pittner, Andreas A1 - Wimpory, Robert A1 - Boin, M. A1 - Kreutzbruck, Marc T1 - Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings N2 - The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction(ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth. KW - GMR KW - Magnetic stray field KW - Neutron diffraction KW - Residual stress KW - TIG-welding PY - 2017 U6 - https://doi.org/10.1016/j.jmmm.2016.11.102 SN - 0304-8853 SN - 1873-4766 VL - 426 SP - 580 EP - 587 PB - Elsevier CY - Amsterdam AN - OPUS4-38678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiel, Erik A1 - Kreutzbruck, M. A1 - Ziegler, Mathias T1 - Laser projected photothermal thermography for characterizing hidden defects N2 - For the last 20 years active thermography has developed into a standard method in non-destructive material testing. It has become possible to detect defects such as cracks, voids, or even material inhomogeneities. Until now, it is still difficult to quantify subsurface or hidden defects in size due to the diffusive nature of heat flow within a solid. Facing this issue, lockin thermography and other photothermal techniques have been established. They are based on exciting a sample periodically (e.g. with a halogen lamp), causing a controlled periodical heat flow and thereby representing strongly damped thermal waves. These techniques make use of interference and reflection of thermal waves which allow enhancing depth resolution. So far, only the temporal component of the light source was modified to achieve a defined vertical heat flow – In contrast, we propose a novel technique in which we are able to control both: time and space. This technique enables us to exploit the possibilities of coherent thermal wave shaping. We achieve that by combining a spatial light modulator (SLM) with a high power laser. This approach allows us to launch a set of individually controlled and fully coherent high energy thermal waves into the sample volume. That means, we intentionally use wave propagation throughout the sample’s material in both - vertical and lateral direction. As one possible application, we use a thermal waves’ interference effect of two phase shifted wave patterns to detect the position of hidden defects. The wave patterns are positioned with a certain distance and a 180° phase shift to each other creating an amplitude depletion zone right in the middle of the two patterns. When a defect is brought unsymmetrically into the depletion zone, the lateral heat flow is disturbed. If the sample is now moved through the depletion zone, a defect can be easily characterized. Exciting periodically while controlling simultaneously phase and amplitude enables us to have a defined thermal wave propagation throughout the sample which means thermal waves can be controlled almost like acoustical or optical waves. This offers the opportunity to transfer known technologies from wave shaping techniques to thermography methods. T2 - 19th World Conference of Non-Destructive Testing 2016 CY - München, Germany DA - 13.06.2016 KW - Thermal waves KW - DMD KW - Active thermography KW - SLM PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-365702 SP - Th.4.I.2 - 1 EP - Th.4.I.2 - 6 AN - OPUS4-36570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiel, Erik A1 - Kreutzbruck, M. A1 - Studemund, T. A1 - Ziegler, Mathias T1 - Thermal wave interference with high-power VCSEL arrays for locating vertically oriented subsurface defects N2 - Among the photothermal methods, full-field thermal imaging is used to characterize materials, to determine thicknesses of layers, or to find inhomogeneities such as voids or cracks. The use of classical light sources such as flash lamps (impulse heating) or halogen lamps (modulated heating) led to a variety of nondestructive testing methods, in particular, lock-in and flash-thermography. In vertical-cavity surface-emitting lasers (VCSELs), laser light is emitted perpendicularly to the surface with a symmetrical beam profile. Due to the vertical structure, they can be arranged in large arrays of many thousands of individual lasers, which allows power scaling into the kilowatt range. Recently, a high-power yet very compact version of such a VCSEL-array became available that offers both the fast timing behavior of a laser as well as the large illumination area of a lamp. Moreover, it allows a spatial and temporal control of the heating because individual parts of the array can be controlled arbitrarily in frequency, amplitude, and phase. In conjunction with a fast infrared camera, such structured heating opens up a field of novel thermal imaging and testing methods. As a first demonstration of this approach, we chose a testing problem very challenging to conventional thermal infrared testing: The detection of very thin subsurface defects perpendicularly oriented to the surface of metallic samples. First, we generate destructively interfering thermal wave fields, which are then affected by the presence of defects within their reach. It turned out that this technique allows highly sensitive detection of subsurface defects down to depths in excess of the usual thermographic rule of thumb, with no need for a reference or surface preparation. T2 - 44TH ANNUAL REVIEW OF PROGRESS IN QUANTITATIVE NONDESTRUCTIVE EVALUATION CY - Provo, Utah DA - 16.07.2017 KW - Laser applications KW - Thermography KW - VCSEL KW - Subsurface defects PY - 2018 SN - 978-0-7354-1644-4 U6 - https://doi.org/10.1063/1.5031547 SN - 0094-243X VL - 1949 SP - UNSP 060001, 1 EP - 8 AN - OPUS4-45171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Myrach, Philipp A1 - Maierhofer, Christiane A1 - Rahammer, M. A1 - Kreutzbruck, Marc T1 - Parameters in lock-in thermography of CFRP laminates N2 - Active thermography with lock-in excitation is a non-destructive testing method that is also feasible for testing of carbon fiber reinforced polymers (CFRP). For validating the method extensive investigations were done during a research project in order to advance a standardization process. The most important parameters of optical and ultrasonic excitation thermography were investigated. For example, the appropriate selection of spectral sensitivity of the used infrared camera systems is important for recording undisturbed thermal signals. Regarding excitation, influences of excitation power and ultrasonic frequency were studied. Furthermore, material parameters such as CFRP layup are known for strongly affecting the results of measurement. KW - Standardisierung KW - Lock-in thermography KW - Lock-in Thermografie KW - CFRP KW - CFK KW - optical excitation KW - ultrasonic excitation KW - Ultraschall KW - standardization PY - 2016 U6 - https://doi.org/10.3139/120.110814 SN - 0025-5300 VL - 58 IS - 1 SP - 31 EP - 35 PB - Carl Hanser Verlag CY - München AN - OPUS4-35479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiel, Erik A1 - Kreutzbruck, M. A1 - Ziegler, Mathias T1 - Spatial and temporal control of thermal waves by using DMDs for interference based crack detection N2 - Active Thermography is a well-established non-destructive testing method and used to detect cracks, voids or material inhomogeneities. It is based on applying thermal energy to a samples’ surface whereas inner defects alter the nonstationary heat flow. Conventional excitation of a sample is hereby done spatially, either planar (e.g. using a lamp) or local (e.g. using a focused laser) and temporally, either pulsed or periodical. In this work we combine a high power laser with a Digital Micromirror Device (DMD) allowing us to merge all degrees of freedom to a spatially and temporally controlled heat source. This enables us to exploit the possibilities of coherent thermal wave shaping. Exciting periodically while controlling at the same time phase and amplitude of the illumination source induces – via Absorption at the sample’s surface - a defined thermal wave propagation through a sample. That means thermal waves can be controlled almost like acoustical or optical waves. However, in contrast to optical or acoustical waves, thermal waves are highly damped due to the diffusive character of the thermal heat flow and therefore limited in penetration depth in relation to the achievable resolution. Nevertheless, the coherence length of thermal waves can be chosen in the mmrange for modulation frequencies below 10 Hz which is perfectly met by DMD technology. This approach gives us the opportunity to transfer known technologies from wave shaping techniques to thermography methods. We will present experiments on spatial and temporal wave shaping, demonstrating interference based crack detection. T2 - Photonics West 2016, OPTO, 9761 CY - San Francisco, CA, USA DA - 15.02.2016 KW - Active thermography KW - Thermal wave KW - Spatial light modulation KW - Crack detection KW - DMD KW - DMD coupled laser PY - 2016 U6 - https://doi.org/10.1117/12.2210918 SN - 0277-786X VL - 9761 SP - 97610N-1 EP - 97610N-13 AN - OPUS4-35587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sonntag, Nadja A1 - Skrotzki, Birgit A1 - Stegemann, Robert A1 - Löwe, Peter A1 - Kreutzbruck, M. T1 - The role of surface topography on deformation-induced magnetization under inhomogeneous elastic-plastic deformation N2 - It is widely accepted that the magnetic state of a ferromagnetic material may be irreversibly altered by mechanical loading due to magnetoelastic effects. A novel standardized nondestructive testing (NDT) technique uses weak magnetic stray fields, which are assumed to arise from inhomogeneous deformation, for structural health monitoring (i.e., for detection and assessment of damage). However, the mechanical and microstructural complexity of damage has hitherto only been insufficiently considered. The aim of this study is to discuss the phenomenon of inhomogeneous “self-magnetization” of a polycrystalline ferromagnetic material under inhomogeneous deformation experimentally and with stronger material-mechanical focus. To this end, notched specimens were elastically and plastically deformed. Surface magnetic states were measured by a three-axis giant magnetoresistant (GMR) sensor and were compared with strain field (digital image correlation) and optical topography measurements. It is demonstrated that the stray fields do not solely form due to magnetoelastic effects. Instead, inhomogeneous plastic deformation causes topography, which is one of the main origins for the magnetic stray field formation. Additionally, if not considered, topography may falsify the magnetic signals due to variable lift-off values. The correlation of magnetic vector components with mechanical tensors, particularly for multiaxial stress/strain states and inhomogeneous elastic-plastic deformations remains an issue. KW - Magnetic stray fields KW - Magnetomechanical effect KW - Damage KW - Topography KW - Multiaxial deformation KW - Notch KW - Plastic deformation KW - Metal magnetic memory KW - Digital image correlation KW - Structural steel PY - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-457878 SN - 1996-1944 VL - 11 IS - 9 SP - 1518, 1 EP - 26 PB - MDPI CY - Basel, Switzerland AN - OPUS4-45787 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stegemann, Robert A1 - Cabeza, Sandra A1 - Pelkner, Matthias A1 - Lyamkin, Viktor A1 - Pittner, Andreas A1 - Werner, Daniel A1 - Wimpory, R. A1 - Boin, M. A1 - Kreutzbruck, Marc A1 - Bruno, Giovanni T1 - Influence of the microstructure on magnetic stray fields of low-carbon steel welds N2 - This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction. Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields. KW - TIG-welding KW - GMR sensors KW - Magnetic stray field KW - Neutron diffraction KW - Residual stress KW - Microstructure KW - Low carbon steel PY - 2018 U6 - https://doi.org/10.1007/s10921-018-0522-0 SN - 0195-9298 SN - 1573-4862 VL - 37 IS - 3 SP - 66,1 EP - 18 PB - Springer US CY - New York AN - OPUS4-45855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sergeeva-Chollet, N. A1 - Decitre, J.-M. A1 - Fermon, C. A1 - Pelkner, Matthias A1 - Reimund, Verena A1 - Kreutzbruck, Marc ED - Chimenti, D.E. ED - Bond, L.J. ED - Thompson, D.O. T1 - Development of eddy current probes based on magnetoresistive sensors arrays N2 - Eddy Current Technique is a powerful method for detection of surface notches and of buried flaws during inspection of metallic parts. Recent EC array probes have demonstrated a fast and efficient control of large surfaces. Nevertheless, when the size of flaws decreases or the defect is rather deep, traditional winding coil probes turn out to be useless. Magnetoresistive sensors present the advantages of flat frequency response and micron size. These sensors are hence very attractive for the detection of buried defects that require low frequencies because of skin depth effect. An optimization of the probe with magnetoresistive sensors as receivers has been made by simulations using CIVA software and finite elements methods with OPERA. EC probes for buried flaw detection have been designed. Experimental results have been compared with simulations. T2 - 40th Annual review of progress in quantitative nondestructive evaluation CY - Baltimore, Maryland, USA DA - 2013-07-21 KW - Eddy current KW - Magnetic sensor PY - 2014 SN - 978-0-7354-1212-5 SN - 978-0-7354-1211-8 U6 - https://doi.org/10.1063/1.4864981 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1581 33B SP - 1374 EP - 1379 PB - AIP Publishing AN - OPUS4-31279 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -