TY - JOUR A1 - Hoang, D. L. A1 - Dittmar, A. A1 - Schneider, M. A1 - Trunschke, A. A1 - Lieske, H. A1 - Brzezinka, Klaus-Werner A1 - Witke, Klaus T1 - Evidence of lanthanum-chromium mixed oxides formed in CrOx/La2O3 model catalysts N2 - CrOx/La2O3 mixed oxides, prepared by impregnating La2O3 with appropriate aqueous solutions of (NH4)2CrO4 and calcining at 600 °C for 4 h, have been investigated by means of XRD, TPR, XPS, DRIFTS, and Raman spectroscopy (RS). The formation of the compounds La2CrO6, La(OH)CrO4 and LaCrO4 under these conditions was evidenced. Strong peaks at 864, 884, 913, and 921 cm-1, as well as weak peaks at 136, 180, 354, 370, and 388 cm-1 in the RS spectrum of CrOx/La2O3 have been assigned to La2CrO6. KW - Lanthanum-chromium mixed oxides KW - La2CrO6 KW - LaCrO4 KW - TPR KW - XPS KW - XRD KW - DRIFTS KW - Raman spectroscopy PY - 2003 DO - https://doi.org/10.1016/S0040-6031(02)00491-4 SN - 0040-6031 SN - 1872-762X VL - 400 SP - 153 EP - 163 PB - Elsevier CY - Amsterdam AN - OPUS4-2397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Richter, M. A1 - Trunschke, A. A1 - Bentrup, U. A1 - Brzezinka, Klaus-Werner A1 - Schreier, E. A1 - Schneider, M. A1 - Pohl, M.-M. A1 - Fricke, R. T1 - Selective Catalytic Reduction of Nitric Oxide by Ammonia over Egg-Shell MnOx/NaY Composite Catalysts N2 - A novel composite catalyst system for the selective catalytic reduction (SCR) of NOx by NH3 is described operating at temperatures lower than 470 K in the presence of water with NO conversions of 80–100% at space velocities of 30,000–50,000 h-1. The catalyst is prepared by egg-shell precipitation of MnO2 on the external surface of zeolite NaY. Structural and thermal stability of precipitated MnO2 as well as of the MnO2/NaY composite catalyst were characterized by N2 adsorption, X-ray diffraction, laser Raman spectroscopy, temperature-programmed reduction, and electron microscopy. MnO2 precipitated on zeolite NaY (15 wt% loading) retained its amorphous state up to calcination temperatures of 775 K. The zeolite component remained structurally intact. Calcination at higher temperatures destroyed the zeolite structure and transformed MnO2 into Mn3O4. DRIFT spectroscopic investigations revealed the presence of symmetric O=N—O—N=O species formally corresponding to N2O3 on the composite catalyst after contact with NO. Catalytic measurements under integral flow conditions showed that the catalyst performance is associated with a close coupling of nitrite formation and its drain off from equilibria with NO/NO2 and nitrate by ammonia. Several results are in line with the “diazotation” mechanism, including NH3 protonation to NH4+, whereas prevailing Lewis acid sites should enable NH3 activation via amide species, thus leading to a parallel “amide/nitrosamide” SCR reaction route. The activity-temperature profile fulfills the requirements of a low-temperature NOx reduction catalyst for mobile diesel engines if an ammonia supply is implemented “on board,” e.g., by urea decomposition. PY - 2002 DO - https://doi.org/10.1006/jcat.2001.3468 SN - 0021-9517 SN - 1090-2694 VL - 206 SP - 98 EP - 113 PB - Acad. Press CY - San Diego, Calif. AN - OPUS4-1638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Knorr, Annett A1 - Koseki, H. A1 - Li, X.-R. A1 - Tamura, M. A1 - Wehrstedt, Klaus-Dieter A1 - Whitmore, M. W. T1 - A closed pressure vessel test (CPVT) screen for explosive properties of energetic organic compounds N2 - Results of a round-robin test on a mini-autoclave are reported and previously proposed criteria reviewed. Criteria based upon the results for three standard materials are now put forward. These standards-based criteria, in contrast to numerical criteria, theoretically allow any laboratory to utilize the data accumulated to date, irrespective of the equipment used. The practical requirement is that adequate discrimination can be achieved. Data to assess this are given. KW - Closed pressure vessel test KW - Mini-autoclave KW - MCPVT KW - Explosive properties PY - 2007 SN - 0950-4230 SN - 1873-3352 VL - 20 IS - 1 SP - 1 EP - 6 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-14385 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brzezinka, Klaus-Werner A1 - Gross, Thomas A1 - Unger, Wolfgang A1 - Ramm, M. A1 - Ata, M. T1 - Studies of amorphous carbon using X-ray photoelectron spectroscopy, near-edge X-ray-absorption fine structure and Raman spectroscopy KW - Amorphous materials KW - Carbon KW - Plasma processing and deposition KW - Structural properties PY - 1999 SN - 0040-6090 VL - 354 SP - 106 EP - 110 PB - Elsevier CY - Amsterdam AN - OPUS4-891 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dressler, M. A1 - Börnstein, Julian A1 - Meinel, M. A1 - Ploska, Ute A1 - Reinsch, Stefan A1 - Hodoroaba, Vasile-Dan A1 - Nicolaides, Dagmar A1 - Wenzel, Klaus-Jürgen T1 - Sol-gel preparation of calcium titanium phosphate: viscosity, thermal properties and solubility N2 - Calcium titanium phosphate (CTP) was prepared by the sol–gel route in order to prepare suitable coatings. This work addresses the question of how to prepare stable CTP sols. Their rheological properties as a function of process parameters like solid loading and water content are investigated. It was found that an increased solid loading as well as an increased water content lead to an increased initial viscosity as well as a more pronounced ageing induced viscosity rise. In addition, the thermal behavior of the resulting xerogels was analyzed. Furthermore, we studied the ion release behavior of the xerogels when brought in contact with water. Results suggest that calcium titanium phosphate shows a diffusion controlled ion release mode with a preferential release of Ca. KW - Calcium titanium phosphate KW - Sol-gel processing KW - Rheology KW - Thermal analysis KW - Coatings KW - Solubility PY - 2012 DO - https://doi.org/10.1007/s10971-011-2653-y SN - 0928-0707 SN - 1573-4846 VL - 62 IS - 3 SP - 273 EP - 280 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-27617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sonntag, Nadja A1 - Cabeza, S. A1 - Kuntner, M. A1 - Mishurova, Tatiana A1 - Klaus, M. A1 - Kling e Silva, L. A1 - Skrotzki, Birgit A1 - Genzel, Ch. A1 - Bruno, Giovanni T1 - Visualisation of deformation gradients in structural steel by macroscopic magnetic domain distribution imaging (Bitter technique) N2 - Abstract While classically used to visualise the magnetic microstructure of functional materials (e.g., for magnetic applications), in this study, the Bitter technique was applied for the first time to visualise macroscopic deformation gradients in a polycrystalline low-carbon steel. Spherical indentation was chosen to produce a multiaxial elastic–plastic deformation state. After removing the residual imprint, the Bitter technique was applied, and macroscopic contrast differences were captured in optical microscopy. To verify this novel characterisation technique, characteristic “hemispherical” deformation zones evolving during indentation were identified using an analytical model from the field of contact mechanics. In addition, near-surface residual stresses were determined experimentally using synchrotron radiation diffraction. It is established that the magnetic domain distribution contrast provides deformation-related information: regions of different domain wall densities correspond to different “hemispherical” deformation zones (i.e., to hydrostatic core, plastic zone and elastic zone, respectively). Moreover, the transitions between these three zones correlate with characteristic features of the residual stress profiles (sign changes in the radial and local extrema in the hoop stress). These results indicate the potential of magnetic domain distribution imaging: visualising macroscopic deformation gradients in fine-grained ferromagnetic material with a significantly improved spatial resolution as compared to integral, mean value-based measurement methods. KW - Bitter technique KW - Deformation KW - Expanding cavity model KW - Indentation KW - Magnetic domain distribution KW - Residual stress PY - 2018 DO - https://doi.org/10.1111/str.12296 SN - 1475-1305 VL - 54 IS - 6 SP - e12296, 1 EP - 15 PB - Wiley AN - OPUS4-46569 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Isleyen, Alper A1 - Can, Suleyman Z. A1 - Cankur, Oktay A1 - Engin, Betul Ari A1 - Vogl, Jochen A1 - Koenig, Maren A1 - Horvat, Milena A1 - Jacimovic, Radojko A1 - Zuliani, Tea A1 - Fajon, Vesna A1 - Jotanovic, Aida A1 - Gaževic, Luka A1 - Milosevic, Milena A1 - Ochsenkuehn–Petropoulou, Maria A1 - Tsopelas, Fotis A1 - Lymberopoulou, Theopisti A1 - Tsakanika, Lamprini-Areti A1 - Serifi, Olga A1 - Ochsenkuehn, Klaus M. A1 - Bulska, Ewa A1 - Tomiak, Anna A1 - Kurek, Eliza A1 - Cakılbahçe, Zehra A1 - Aktas, Gokhan A1 - Altuntas, Hatice A1 - Basaran, Elif A1 - Kısacık, Barıs A1 - Gumus, Zeynep T1 - Certification of the total element mass fractions in UME EnvCRM 03 soil sample via a joint research project N2 - Soil certified reference material (CRM), UME EnvCRM 03 was produced by a collaborative approach among national metrology institutes, designated institutes and university research laboratories within the scope of the EMPIR project: Matrix Reference Materials for Environmental Analysis. This paper presents the sampling and processing methodology, homogeneity, stability, characterization campaign, the assignment of property values and their associated uncertainties in compliance with ISO 17034:2016. The material processing methodology involves blending a natural soil sample with a contaminated soil sample obtained by spiking elemental solutions for 8 elements (Cd, Co, Cu, Hg, Ni, Pb, Sb and Zn) to reach the level of warning risk monitoring values specified for metals and metalloids of soils in Europe. Comparative homogeneity and stability test data were obtained by two different institutes, ensuring the reliability and back up of the data. The certified values and associated expanded uncertainties for the total mass fractions of thirteen elements (As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sb, V and Zn) are established. The developed CRM can be used for the development and validation of measurement procedures for the determination of the total mass fractions of elements in soil and also for quality control/assurance purposes. The developed CRM is the first example of a soil material originating from Türkiye. KW - Total element content KW - Soil KW - CRM KW - Certification KW - Environmental pollution monitoring PY - 2024 DO - https://doi.org/10.1007/s00769-024-01597-8 SN - 1432-0517 VL - 29 SP - 293 EP - 301 PB - Springer Science and Business Media LLC AN - OPUS4-59954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Isleyen, Alper A1 - Can, Suleyman Z. A1 - Cankur, Oktay A1 - Engin, Betul Ari A1 - Vogl, Jochen A1 - Koenig, Maren A1 - Horvat, Milena A1 - Jacimovic, Radojko A1 - Zuliani, Tea A1 - Fajon, Vesna A1 - Jotanovic, Aida A1 - Gaževic, Luka A1 - Milosevic, Milena A1 - Ochsenkuehn–Petropoulou, Maria A1 - Tsopelas, Fotis A1 - Lymberopoulou, Theopisti A1 - Tsakanika, Lamprini-Areti A1 - Serifi, Olga A1 - Ochsenkuehn, Klaus M. A1 - Bulska, Ewa A1 - Tomiak, Anna A1 - Kurek, Eliza A1 - Cakılbahçe, Zehra A1 - Aktas, Gokhan A1 - Altuntas, Hatice A1 - Basaran, Elif A1 - Kısacık, Barıs A1 - Gumus, Zeynep T1 - Correction: Certification of the total element mass fractions in UME EnvCRM 03 soil sample via a joint research project N2 - In this article the author’s name Betul Ari Engin was incorrectly written as Murat Tunc. The original article has been corrected. PY - 2024 DO - https://doi.org/10.1007/s00769-024-01611-z VL - 29 SP - 303 PB - Springer Science and Business Media LLC AN - OPUS4-60824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stephan-Scherb, Christiane A1 - Nützmann, Kathrin A1 - Kranzmann, Axel A1 - Klaus, M. A1 - Genzel, C. T1 - Real time observation of high temperature oxidation and sulfidation of Fe-Cr model alloys N2 - Insights into early damage mechanisms during high-temperature gas corrosion provide important aspects for the prediction of the long-term stability of hightemperature materials exposed to a hot and corrosive environment. The current work presents a real time study concerning the combined oxidation and sulfidation of ferritic model alloys in a hot SO2 containing atmosphere using energy dispersive X-ray diffraction. The applied high temperature reactor allows the transmittance of high energetic X-rays in order to collect X-ray diffraction pattern of the sample surface in situ during the reaction with the reactive environment. The results revealed that the first phases crystallizing on iron with 2 wt% chromium and with 9 wt% chromium are oxides. The aging experiments at T = 650° C with 0.5% SO2 and 99.5% Ar were followed in situ and caused an external mixed oxide-sulfide layer on top of iron with 2 wt% chromium. On the higher alloyed material the external scale consists of iron oxides and the inner scale of mixed (Fe,Cr)-oxides and chromium-sulfides. The oxide content continuously increases parallel to an increase of the sulfide amount. Thus, the initially formed (Fe,Cr)-oxides do not have a protective character and support the transport of sulfur through the growing oxide scale. KW - High temperature corrosion KW - In situ diffraction KW - Sulfidation PY - 2018 DO - https://doi.org/10.1002/maco.201709892 SN - 0947-5117 VL - 69 IS - 6 SP - 678 EP - 689 PB - Wiley VCH Verlag AN - OPUS4-44776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Taming the silicon tetraazide beast N2 - Highly energetic silicon tetraazide 1 is synthesized safely in high yield and high purity. The compound is prepared as a solution in benzene which allows it to be handled safely. Stable Lewis base adducts of Si(N3)4 (e.g. 2) are also prepared by treatment of either Si(N3)4 or the di­sodium salt of hexaazidosilicate (3) with Lewis bases (2,2-bipyridine or 1,10-phenanthroline). Unlike Si(N3)4 the Lewis base adduct 2 is thermally stable and does not decompose below 265 °C. The decomposition is very energetic (ΔHd = -2.4 kJg-1) which means 2 and related Lewis base ­adducts could replace environmentally harmful Pb(N3)4 used as primary explosive. KW - Highly energetic silicon tetraazide KW - Lewis base adducts KW - Azides KW - Silicon KW - Energetic materials PY - 2011 DO - https://doi.org/10.1055/s-0030-1259150 SN - 1861-1958 VL - 1 SP - 0043 EP - 0043 PB - Thieme CY - Stuttgart AN - OPUS4-32352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malow, Marcus A1 - Wehrstedt, Klaus-Dieter A1 - Schuurman, P. A1 - Hoeijmakers, P.M.M. T1 - Comments on 'thermal decomposition kinetic evaluation and its thermal hazards prediction of AIBN, by S. Guo, W. Wan, C. Chen and W.H. Chen' (Journal of thermal analysis and calorimetry (2013) 113:1169-1176, DOI 10.1007/s10973-013-2993-7) N2 - We read the paper by Guo et al. [1] with interest. The authors have investigated the thermal decomposition kinetics and thermal hazards of 2,2′-azobis(isobutyronitrile), AIBN, by differential scanning calorimetry (DSC) and used the Advanced Kinetics and Technology Solutions (AKTS) software to predict the thermal stability of AIBN in ton and kg scale. The main conclusion of interest is that the self-accelerating decomposition temperature (SADT) of a 50-kg standard package is 63 °C. PY - 2014 DO - https://doi.org/10.1007/s10973-014-3897-x SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 117 IS - 3 SP - 1015 EP - 1016 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-31251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vela, I. A1 - Chun, Hyunjoo A1 - Mishra, Kirti Bhushan A1 - Gawlowski, M. A1 - Sudhoff, P. A1 - Rudolph, Michael A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Vorhersage der thermischen Strahlung großer Kohlenwasserstoff- und Peroxid-Poolfeuer mit CFD Simulation KW - CFD Simulation KW - Poolfeuer KW - JP-4 KW - Kerosin KW - Di-tert-butylperoxid KW - Thermische Strahlung PY - 2009 DO - https://doi.org/10.1007/s10010-009-0094-3 SN - 0015-7899 SN - 1434-0860 VL - 73 IS - 2 SP - 87 EP - 97 PB - Springer CY - Berlin AN - OPUS4-19531 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, Klaus-Dieter A1 - Adams, W. D. A1 - Mak, W. A1 - Malow, Marcus A1 - Kumasaki, M. T1 - Report about the IGUS EOS meeting 2010 in Tokyo KW - IGUS KW - EOS KW - Organic peroxides KW - Self-reactive substances KW - Energetic materials KW - Test methods KW - Oxidizers KW - Ammonium nitrate KW - Fertilizers PY - 2010 SN - 0570-4480 N1 - Sprachen: Japanisch/Englisch - Languages: Japanese/English VL - 49 IS - 4 SP - 240 EP - 243 CY - Tokyo, Japan AN - OPUS4-21942 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Neutrale Lewis-Basen-Addukte des Siliciumtetraazids KW - Azide KW - Hyperkoordination KW - N-Liganden KW - Silicium KW - Stickstoffreiche Verbindungen PY - 2010 DO - https://doi.org/10.1002/ange.201001826 SN - 0044-8249 SN - 0932-2140 SN - 1521-3757 VL - 122 IS - 43 SP - 8185 EP - 8189 PB - Wiley-VCH CY - Weinheim AN - OPUS4-22201 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Neutral lewis base adducts of silicon tetraazide KW - Silicon KW - Azides KW - Hypercoordination KW - Nitrogen-rich compounds KW - N-ligands PY - 2010 DO - https://doi.org/10.1002/anie.201001826 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 49 IS - 43 SP - 8013 EP - 8016 PB - Wiley-VCH CY - Weinheim AN - OPUS4-22202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Feist, M. A1 - Troyanov, S.I. A1 - Mehner, Hartmut A1 - Witke, Klaus A1 - Kemnitz, E. T1 - Zwei Oxidationsstufen und vier verschiedene Koordinationen von Eisen in einer Verbindung. Synthese, Kristallstruktur und spektroskopische Charakterisierung von 1,4-Dimethylpiperazinium-Chloroferrat(II, III), (dmpipzH2)6[FeIICl4]2[FeIIICl4]2[FeIICl5] [FeIIICl6] KW - 1,4-Dimethylpiperazinium chloroferrate(II,III) KW - Crystal Structure KW - Trigonal-bipyramidal pentachloroferrate(II) KW - Mössbauer, Raman spectroscopy PY - 1999 SN - 0044-2313 SN - 1521-3749 SN - 0372-7874 SN - 0863-1786 SN - 0863-1778 IS - 625 SP - 141 EP - 146 PB - Wiley-VCH CY - Weinheim AN - OPUS4-2305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steensma, M. A1 - Schuurman, P. A1 - Malow, Marcus A1 - Krause, Ulrich A1 - Wehrstedt, Klaus-Dieter T1 - Evaluation of the validity of the UN SADT H.4 test for solid organic peroxides and self-reactive substances N2 - Many self-accelerating decomposition temperatures (SADTs) of solid organic peroxides and self-reactive substances have been determined with the UN test method H.4, which is a scaled down test in a small Dewar vessel. For solid organic peroxides and solid self-reactive substances Fierz has questioned this procedure in a recent paper. Fierz concluded that the Dewar test results should not be extrapolated to beyond 8 l packages, owing to the thermal insulation value of solids. On the other hand, long term experience with the test, with a great variety of solid organic peroxides and self-reactive substances show about equal critical temperatures in the small Dewar vessel and on 50 kg scale. In the present work, we first checked, by numerical simulations, the Dewar scale versus the larger scale, in a way comparable with Fierz’ method: both scales are simulated by spheres, consisting of a number of annular layers, for the large scale the usual external heat loss term is used but for the small scale the outside heat transfer is strongly limited. The outcome of these simulations, covering a variety of physical parameters, supports the concerns expressed by Fierz. After this, we performed accurate cooling and heating experiments with solid organic peroxide in the usual Dewar vessel, provided with a large set of thermocouples. The results of these experiments showed that the simulation model for the Dewar vessel has to be changed from a spherical analogue to a short cylinder of solid material with heat exchange mainly via its top (Utop 3.5 W/(m2 K), overall heat transfer coefficient) and some heat exchange (Uside 0.29 W/(m2 K)) through its cylindrical and bottom part. With this “modified cylinder” model (being neither an infinitely long cylinder nor a slab) of the Dewar vessel, we found that the UN method H.4 enables an accurate prediction of the SADT, with small deviations of 0 ± 2.5 °C. Further, by performing a truly three-dimensional (3D) finite element calculation in FEMLAB, the new heat characteristics of the Dewar vessel as well as a 50 kg package of dilauroyl peroxide, a solid organic peroxide, were checked. The outcome was compared with the critical ambient temperatures known for various package sizes, which agreed well. KW - SADT of solids KW - Transport regulations KW - UN H.4 test (HAST) KW - Numerical simulations KW - Scale-up procedure PY - 2005 DO - https://doi.org/10.1016/j.jhazmat.2004.09.028 SN - 0304-3894 VL - 117 IS - 2-3 SP - 89 EP - 102 PB - Elsevier CY - Amsterdam AN - OPUS4-5604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, Klaus-Dieter A1 - Rudolph, Michael A1 - Zemke, Gerhard-Reinhard A1 - Dischl, G. A1 - Maier, M. T1 - Deckelflug - Können Organische Peroxide vom Typ D unter Umständen in Doppelkammer-Stahl-IBC mit Verdünnungsautomatik befördert werden? Das zeigte ein Brandversuch. KW - Brandprüfung KW - Organisches Peroxid KW - Stahl-IBC PY - 2005 SN - 0016-5808 VL - 50 IS - 4 SP - 22 EP - 23 PB - Storck CY - Hamburg AN - OPUS4-7342 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Wrobel, J. M. A1 - Brzezinka, Klaus-Werner A1 - Esser, N. A1 - Kautek, Wolfgang T1 - Femtosecond laser irradiation of indium phosphide in air: Raman spectroscopic and atomic force microscopic investigations KW - Femtosecond laser ablation KW - Indium phosphide KW - Raman spectroscopy KW - Atomic force microscopy PY - 2002 SN - 0169-4332 SN - 1873-5584 VL - 202 SP - 272 EP - 282 PB - North-Holland CY - Amsterdam AN - OPUS4-2645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Faensen, M. A1 - Rahmanzadeh, R. A1 - Naseband, Klaus T1 - Untersuchungen an einem modifizierten Schaft zur dauerhaften Verankerung von Hüftgelenkprothesen PY - 1980 SN - 0013-5585 SN - 1862-278X VL - 25 SP - 160 EP - 163 PB - De Gruyter CY - Berlin AN - OPUS4-9250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hellmuth, K.-H. A1 - Klobes, Peter A1 - Meyer, Klaus A1 - Röhl-Kuhn, Barbara A1 - Siitari-Kauppi, M. A1 - Hartikainen, K. A1 - Hartikainen, J. A1 - Timonen, J. T1 - Matrix retardation studies: size and structure of the accessable pore space in fresh and altered crystalline rock N2 - For the assessment of the barrier function of the geosphere around a nuclear waste repository information about the nature of the accessible rock pore space and internal surfaces is needed. Intact samples of various types of fresh and altered crystalline rocks have been studied by means of mercury intrusion porosimetry and gas adsorption methods using various adsorbates. Furthermore, fluorescence microscopy and scanning electron microscopy was applied and the results were compared with those of impregnation with carbon-l4-polymethylmethacrylate (PMMA). Additional structural information was derived from hydraulic conductivity determinations using helium gas. The investigations were focussed on the reliability of these measurements of intact core samples, the influence of rock composition, structure and geological evolution on the microstructure of the matrices and the consequences regarding the retardation properties of the bedrock. PY - 1995 SN - 0303-4534 VL - 23 IS - 5/6 SP - 691 EP - 706 PB - Verl. für Geowissenschaften Wutzke CY - Berlin AN - OPUS4-11979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hellmuth, K.-H. A1 - Siitari-Kauppi, M. A1 - Klobes, Peter A1 - Meyer, Klaus A1 - Goebbels, Jürgen T1 - Imaging and Analyzing Rock Porosity by Autoradiography and Hg-porosimetry/X-ray Computertomography-Applications N2 - The application of two sets of methods for the characterization of rock pore systems is reported. Both are discussed in the context of other techniques described in the literature. (i) Impregnation with labelled polymethylmethacrylate (PMMA) and autoradiography or direct measurement of the tracer activity allows the investigation of the pattern of the spatial porosity distribution and quantitative measurement of mineral-specific, local porosities, porosity gradients as well as an assessment of hydraulic and diffusive transport properties. (ii) Quantitative information on surface areas within certain pore size ranges can be achieved by combination of mercury intrusion porosimetry with X-ray absorption computertomography. As examples of applications of these techniques, the effects of weathering, alteration, mechanical stress and large diameter coring on the pore network of rocks have been studied. PY - 1999 SN - 1464-1895 VL - 24 IS - 7 SP - 569 EP - 573 PB - Pergamon CY - Oxford AN - OPUS4-11980 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Link, T. A1 - Epishin, Alexander A1 - Klaus, M. A1 - Brückner, Udo A1 - Reznicek, A. T1 - (100) Dislocations in nickel-base superalloys: Formation and role in creep deformation N2 - α(1 0 0) Dislocations are observed in nickel-base superalloys after creep deformation at high temperatures and low stresses. They are formed in the γ/γ´ interfaces by a three step mechanism. First, primary dislocations with Burgers vector α/2(1 0 1) and 60° character are left behind in the interfaces when dislocation loops glide through the γ channels. The 60° dislocations move into edge orientation and react forming secondary dislocations α/2(1 1 0). In the third step, new primary dislocations are knit into the already existing meshes of primary and secondary dislocations, which results in hexagonal misfit dislocation networks consisting of secondary dislocations α/2(1 1 0) and tertiary dislocations α(1 0 0), both of edge type. This self-organisation process is explained by dislocation theory and crystallography. Creep deformation accelerates when the α(1 0 0) interfacial dislocations enter the γ´ phase. During their climb towards the opposite interface, they attain a characteristic rectangular shape. This shape and the importance of the α(1 0 0) super dislocations for creep deformation are discussed. KW - Superalloys KW - Creep KW - Dislocation reactions KW - Dislocation theory KW - Deformation mechanisms PY - 2005 SN - 0921-5093 SN - 1873-4936 VL - 405 IS - 1-2 SP - 254 EP - 265 PB - Elsevier CY - Amsterdam AN - OPUS4-11968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Klobes, Peter A1 - Riesemeier, Heinrich A1 - Meyer, Klaus A1 - Goebbels, Jürgen A1 - Siitari-Kauppi, M. A1 - Hellmuth, K.-H. ED - Gray, W. T1 - Investigation of rock samples using x-ray-microcomputer-tomography before and after mercury intrusion porosimetry N2 - A new method for the physical characterization of rock matrices for use in site investigations of nuclear waste repositories has been developed. The method can provide information needed in the assessment of the performance of the geosphere working as a natural barrier retarding the migration of radionuclides by diffusion into the rock matrix. Most conventional methods for the physical characterization of rocks give only bulk information. The combination of mercury porosimetry and computer tomography can give 3-D data on mineral-specific porosity distributions with additional pore size information. Additionally, limits for mineral-specific internal surface areas can be estimated, which is essential for the assessment of water-rock interaction and reactive interaction with radionuclides (sorption). Results of measurements on granitic rock (granodiorite) from the Baltic shield are discussed and integrated with results by complementary methods. T2 - 20th Materials Research Society Symposium on the Scientific Basis for Nuclear Waste Management CY - Boston, MA, USA DA - 1996-12-02 PY - 1997 SN - 1-558-99369-X SN - 0272-9172 N1 - Serientitel: Materials Research Society symposium proceedings – Series title: Materials Research Society symposium proceedings IS - 465 SP - 863 EP - 870 PB - Materials Research Society CY - Pittsburgh, Pa. AN - OPUS4-11971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Alexander, I. A1 - Braun, H.-J. A1 - Dettmann, T. A1 - Fimmen, H. A1 - Haberkamp, H. A1 - Katz, H. A1 - Krischok, Frank A1 - Otremba, Frank A1 - Pötzsch, Klaus-Michael A1 - Zentgraf, R. A1 - Putzschke, M. T1 - Bericht über den Ablauf und die Ursachen der Havarie des Tankmotorschiffes 'Waldhof' am 13. Januar 2011 auf dem Mittelrhein (Rhein-km 553,75) KW - Schiffshavarie KW - Gefahrgut-Tankschiff KW - Schwimmstabilität PY - 2013 IS - S-312.4/016 SP - 1 EP - 224 AN - OPUS4-27729 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kozich, V. A1 - Werncke, W. A1 - Dreyer, J. A1 - Brzezinka, Klaus-Werner A1 - Rini, M. A1 - Elsaesser, T. T1 - Vibrational excitation and energy redistribution after ultrafest internal conversion in 4-nitroaniline N2 - Nonequilibrium vibrational excitations of para-nitroaniline (PNA, 4-nitroaniline) occurring after internal conversion from the photoexcited charge transfer state are studied by picosecond anti-Stokes Raman scattering. Vibrational excess populations with distinctly different picosecond rise and decay times are found for a number of modes with frequencies between 860 and 1510 cm–1, including the overtone of a non-Raman active mode. A nonthermal distribution of vibrational populations exists up to about 6 ps after photoexcitation. The time-resolved experiments are complemented by steady-state infrared and Raman measurements as well as calculations based on density functional theory, providing a detailed analysis of the steady-state vibrational spectra of PNA and two of its isotopomers. A weakly Raman active vibration at about 1510 cm–1 displays the fastest rise time and a pronounced excess population and—thus—represents the main accepting mode. We suggest that an out-of-plane mode giving rise to the overtone Raman band at this frequency acts both as coupling and accepting mode in the internal conversion process. PY - 2002 DO - https://doi.org/10.1063/1.1482698 SN - 0021-9606 SN - 1089-7690 VL - 117 IS - 2 SP - 719 EP - 726 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-1637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Witke, Klaus A1 - Kunze, Ralf A1 - Neubert, Dietmar A1 - Mehner, Hartmut A1 - Feist, M. A1 - Kemnitz, E. T1 - Two oxidation states and four different coordinations of iron in an unusual chloro complex: TG-MS, Raman and Mössbauer spectroscopic investigations of the thermal behaviour N2 - Conventional simultaneous thermal analysis, capillary-coupled TG–MS, in situ and ex situ Raman and Mössbauer spectroscopy, as well as chemical analysis have been used for the investigation of the first decomposition step of the mixed valence chloroferrate (dmpipzH2)6[Fe(II)Cl4]2[Fe(III)Cl4]2[Fe(II)Cl5][Fe(III)Cl6]. Under argon at ca. 200°C, an almost complete reduction proceeds in a solid state reaction forming Fe(II). It is accompanied by the release of HCl and, to a minor degree, carbon containing species. A multi-phase product with at least two chloroferrate species, coke, and C,H,N-containing polymers is formed. Binuclear iron complexes, such as (dmpipzH)2[Fe(II)2Cl6], and small amounts of (dmpipzH)[Fe(III)Cl4] have been proposed to be the major and minor component of the product mixture, respectively. KW - Mixed valence chloroferrate KW - Thermal decomposition KW - Intramolecular reduction PY - 2000 DO - https://doi.org/10.1016/S0040-6031(00)00546-3 SN - 0040-6031 SN - 1872-762X VL - 361 IS - 1-2 SP - 53 EP - 60 PB - Elsevier CY - Amsterdam AN - OPUS4-988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhang, Yue A1 - Martin, A. A1 - Wolf, G.-U. A1 - Rabe, S. A1 - Worzala, H. A1 - Lücke, B. A1 - Meisel, M. A1 - Witke, Klaus T1 - Structural transformations of VOHPO4.1/2H2O in the Presence of Ammonia KW - Vanadium KW - Ammoniak KW - Phosphat KW - Phyrophosphorsäure PY - 1996 SN - 0897-4756 SN - 1520-5002 VL - 8 IS - 5 SP - 1135 EP - 1140 PB - American Chemical Society CY - Washington, DC AN - OPUS4-684 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mehner, Hartmut A1 - Witke, Klaus A1 - Feist, M. A1 - Troyanov, S.I. A1 - Kemnitz, E. T1 - Halogenometallate von Übergangselementen mit Kationen stickstoffhaltiger heterozyklischer Basen. VII Zwei Oxidationsstufen und vier verschiedene Koordinationen von Eisen in einer Verbindung. Synthese, Kristallstruktur und spektroskopische Charakterisierung von 1,4-Dimethylpiperazinium-Chloroferrat(II, III), (dmpipzH2)6[FeIICl4]2[FeIIICl4]2[FeIICl5] [FeIIICl6] KW - Halogenometallate KW - Spektroskopische Charakterisierung PY - 1999 SN - 0044-2313 SN - 1521-3749 SN - 0372-7874 SN - 0863-1786 SN - 0863-1778 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 625 IS - 1 SP - 141 EP - 146 PB - Wiley-VCH CY - Weinheim AN - OPUS4-738 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mishurova, Tatiana A1 - Cabeza, Sandra A1 - Artzt, Katia A1 - Haubrich, J. A1 - Klaus, M. A1 - Genzel, Ch. A1 - Requena, G. A1 - Bruno, Giovanni T1 - An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V N2 - Ti-6Al-4V bridges were additively fabricated by selective laser melting (SLM) under different scanning speed conditions, to compare the effect of process energy density on the residual stress state. Subsurface lattice strain characterization was conducted by means of synchrotron diffraction in energy dispersive mode. High tensile strain gradients were found at the frontal surface for samples in an as-built condition. The geometry of the samples promotes increasing strains towards the pillar of the bridges. We observed that the higher the laser energy density during fabrication, the lower the lattice strains. A relief of lattice strains takes place after heat treatment. KW - Selective laser melting KW - Additive manufacturing KW - Heat treatment KW - Ti-6Al-4V KW - Synchrotron X-ray diffraction KW - Residual stress PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-395759 DO - https://doi.org/10.3390/ma10040348 SN - 1996-1944 VL - 10 IS - 4 SP - Article 348, 1 EP - 14 AN - OPUS4-39575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, Jakob A1 - Mishurova, Tatiana A1 - Fritsch, Tobias A1 - Serrano-Munoz, Itziar A1 - Evans, Alexander A1 - Sprengel, Maximilian A1 - Klaus, M. A1 - Genzel, C. A1 - Schneider, J. A1 - Bruno, Giovanni T1 - On the influence of heat treatment on microstructure and mechanical behavior of laser powder bed fused Inconel 718 N2 - A range of heat treatments have been developed for wrought Inconel 718 to obtain desired properties. For additively manufactured Inconel 718, the recently developed standard ASTM F3301 provides guidance for heat treatment of powder bed fusion specimens. Although this standard is based on standards developed for wrought Inconel 718, it does not include direct aging. Since direct aging reduces the number of processing steps, it can result in a post processing cost reduction if the desired properties are obtained. In this study, we characterized the microstructure and tensile behavior of Inconel 718 specimens produced by a laser powder bed fusion process. The specimens were heat treated according to two different routines after stress relieving: a full heat Treatment versus a one-step direct aging process. Differences in the resulting texture and grain morphology were observed. The ex-situ stress-strain behavior was broadly similar. However, a slight increase in yield strength was observed for the direct aged specimen. In order to understand this behavior, investigations with in-situ synchrotron Energy dispersive X-ray diffraction tensile testing revealed differences in the load partitioning among different Crystal directions. Importantly, the elastic anisotropy expressed by the magnitude of the diffraction elastic constants showed a dependency on the microstructures. KW - Electron microscopy KW - X-ray analysis KW - Inconel 718 KW - Additive Manufacturing KW - Mechanical behavior KW - Diffraction elastic constants PY - 2021 DO - https://doi.org/10.1016/j.msea.2020.140555 VL - 805 SP - 40555 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-52142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roveda, Ilaria A1 - Serrano-Munoz, Itziar A1 - Mishurova, Tatiana A1 - Madia, Mauro A1 - Pirling, T. A1 - Evans, Alexander A1 - Klaus, M. A1 - Haubrich, J. A1 - Requena, G. A1 - Bruno, Giovanni T1 - Influence of a 265 °C heat treatment on the residual stress state of a PBF-LB/M AlSi10Mg alloy N2 - Laser Powder Bed Fusion (PBF-LB/M) additive manufacturing (AM) induces high magnitude residual stress (RS) in structures due to the extremely heterogeneous cooling and heating rates. As the RS can be deleterious to the fatigue resistance of engineering components, great efforts are focused on understanding their generation and evolution after post-process heat treatments. In this study, one of the few of its kind, the RS relaxation induced in an as-built PBF-LB/M AlSi10Mg material by a low-temperature heat treatment (265 °C for 1 h) is studied by means of X-ray and neutron diffraction. Since the specimens are manufactured using a baseplate heated up to 200 °C, low RS are found in the as-built condition. After heat treatment a redistribution of the RS is observed, while their magnitude remains constant. It is proposed that the redistribution is induced by a repartition of stresses between the a-aluminium matrix and the silicon phase, as the morphology of the silicon phase is affected by the heat treatment. A considerable scatter is observed in the neutron diffraction RS profiles, which is principally correlated to the presence (or absence) of pockets of porosity developed at the borders of the chessboard pattern. KW - Neutron diffraction KW - Additive manufacturing PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-565115 DO - https://doi.org/10.1007/s10853-022-07997-w SN - 1573-4803 VL - 57 SP - 22082 EP - 22098 PB - Springer Science + Business Media CY - Dordrecht AN - OPUS4-56511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Riesemeier, Heinrich A1 - Ecker, Klaus A1 - Görner, Wolf A1 - Müller, Bernd R. A1 - Radtke, Martin A1 - Krumrey, M. T1 - Layout and first XRF Applications of the BAMline at BESSY II+ N2 - The first hard x-ray beamline at BESSY II has been installed by BAM and PTB at a superconducting 7 T wavelength shifter. The main optical elements of the beamline are a double-multilayer monochromator and a double-crystal monochromator. Depending on the application, the two devices are used separately or in-line. The main applications of the monochromatic radiation with photon energies up to 60 keV are x-ray fluorescence analysis, micro computed tomography, x-ray topography, detector calibration and reflectometry. Calculable undispersed radiation up to 200 keV is available for radiometric applications. KW - BAMline KW - XRF PY - 2005 DO - https://doi.org/10.1002/xrs.750 SN - 0049-8246 VL - 34 IS - 2 SP - 160 EP - 163 PB - Wiley CY - Chichester AN - OPUS4-11929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Gawlowski, M. A1 - Schönbucher, A. T1 - Validation of submodels for CFD simulation of n-hexane pool flames including interferometry N2 - Computational fluid dynamics (CFD) simulation is used to predict transient and time-averaged glame temperatures and species concentrations of an n-hexane pool flame. Employing a combination of an assumed probability density function approach with laminar flamelets using detailed kinetic data and large-eddy simulation with Smagorinsky submodel is shown to be a promising way in modeling pool and tank fires. The measured species concentration and flame temperature profiles from gas chromatography, thermocouple measurements and holographic interferometry are used to validate the submodels for CFD simulation of pool flames. KW - Computational fluid dynamics (CFD) KW - Interferometry KW - Large eddy simulation (LES) KW - Non-premixed flame KW - Pool fire PY - 2012 DO - https://doi.org/10.1002/cite.201100179 SN - 0009-286X SN - 1522-2640 VL - 84 IS - 4 SP - 484 EP - 490 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25418 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Som, Tirtha A1 - Troppenz, G.V. A1 - Wendt, R. R. A1 - Wollgarten, M. A1 - Rappich, J. A1 - Emmerling, Franziska A1 - Rademann, Klaus T1 - Graphene oxide/alpha-Bi2O3 composites for visible-light photocatalysis, chemical catalysis, and solar energy conversion N2 - The growing challenges of environmental purification by solar photocatalysis, precious-metal-free catalysis, and photocurrent generation in photovoltaic cells receive the utmost global attention. Here we demonstrate a one-pot, green chemical synthesis of a new stable heterostructured, ecofriendly, multifunctional microcomposite that consists of α-Bi2O3 microneedles intercalated with anchored graphene oxide (GO) microsheets (1.0 wt?%) for the above-mentioned applications on a large economical scale. The bare α-Bi2O3 microneedles display two times better photocatalytic activities than commercial TiO2 (Degussa-P25), whereas the GO-hybridized composite exhibits approximately four to six times enhanced photocatalytic activities than the neat TiO2 photocatalyst in the degradation of colored aromatic organic dyes (crystal violet and rhodamine 6G) under visible-light irradiation (300 W tungsten lamp). The highly efficient activity is associated with the strong surface adsorption ability of GO for aromatic dye molecules, the high carrier acceptability, and the efficient electron–hole pair separation in Bi2O3 by individual adjoining GO sheets. The introduction of Ag nanoparticles (2.0 wt?%) further enhances the photocatalytic performance of the composite over eightfold because of a plasmon-induced electron-transfer process from Ag nanoparticles through the GO sheets into the conduction band of Bi2O3. The new composites are also catalytically active and catalyze the reduction of 4-nitrophenol to 4-aminophenol in the presence of borohydride ions. Photoanodes assembled from GO/α-Bi2O3 and Ag/GO/α-Bi2O3 composites display an improved photocurrent response (power conversion efficiency ~20?% higher) over those prepared without GO in dye-sensitized solar cells. KW - Bismuth KW - Dyes/pigments KW - Environmental chemistry KW - Graphene KW - Photochemistry PY - 2014 DO - https://doi.org/10.1002/cssc.201300990 SN - 1864-5631 SN - 1864-564X VL - 7 IS - 3 SP - 854 EP - 865 PB - Wiley-VCH CY - Weinheim AN - OPUS4-30390 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - King, M.J. A1 - Iacobucci, P.A. A1 - Mak, W.A. A1 - Wehrstedt, Klaus-Dieter T1 - Report about the IGUS EOS meeting 2011 in Washington, D.C. N2 - IGUS is the International Group of Experts on the Explosion Risks of Unstable Substances. IGUS was established in 1962 with the objective to harmonize test methods used by different countries to identify and quantify the explosive properties of unstable materials. Over the years, IGUS has continued to offer scientists, who are advisers to their governments, and others, a forum to exchange data and information. The Energetic and Oxidizing Substances (EOS) working group as a sub-group of IGUS is dealing with test methods, Classification and safety aspects relating to organic peroxides, self-reactive substances and other energetic substances, fertilizers, ammonium nitrate and oxidizers. The EOS working group holds an annual meeting alternating between Europe, the United States and Japan. The 2011 meeting took place from the 27th to the 29th of April 2011 at the Madison Hotel in Washington, D. C. The meeting was hosted by the Organic Peroxide Producers Safety Division (OPPSD) of the Society of Plastics Industry, Inc. (SPI). This was the fourth EOS meeting held in the USA since 1994. Of particular importance is the fact that 39 colleagues from authorities, universities, research institutes and industries attended the meeting. The delegates came from USA, Canada, China, France, The Netherlands, Norway, Sweden, Italy, Japan, United Kingdom and Germany. This confirms the breadth and scope of this forum and the value the participants associate with being able to contact other colleagues from around the world enabling the effective exchange of scientific results and discussion on the wide-ranging Problems concerning energetic and oxidizing materials. T2 - IGUS EOS Meeting 2011 CY - Washington D.C., USA DA - 27.04.2011 KW - IGUS KW - EOS KW - Organic peroxides KW - Self-reactive substances KW - Test methods KW - Oxidizers KW - Round robin test PY - 2011 SP - 1 EP - 4 AN - OPUS4-26364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Menrad, Andreas A1 - Goedecke, Thomas A1 - Gründer, Klaus-Peter A1 - Wagner, M.H. T1 - The internal pressure test in experiment and simulation - Influence of the wall thickness variation and the change of the packaging behavior after the impact of standard liquids N2 - The effect of the wall thickness variation of blow-moulded bodies made of high-density polyethylene on an internal pressure test after prestoring the packaging with standard liquids was evaluated in experiments and simulations. The objects of the investigation were jerrycans used for the transportation and storage of dangerous goods. The wall thickness was determined using two alternative methods to the magnetostatic measurement. These alternative methods are used for research purpose to get a volumetric model of the jerrycan wall as a geometric model for the simulation. The comparison of the experiments and the simulations of the internal pressure test were performed using the digital image correlation method. The integral strain and deformation of the whole jerrycan was detected by measuring the total mass of the jerrycan being filled with water during the internal pressure test. This is a suitable alternative to the optical measurements of local deformation by the digital image correlation method. Prestorage at 40°C without the influence of chemicals strengthens the jerrycan, whereas the swelling effect of butyl acetate and hydrocarbon mixture softens the jerrycan. The comparison with the experiment is necessary to verify the accuracy of the simulation. It shows that the deformation can be simulated more precisely by using the actual measured geometry. The weakening of the high-density polyethylene caused by a hydrocarbon mixture can be simulated using the Arrhenius equation. The aim of the simulation was to discover whether it is possible to use specimens to predict the behaviour of a packaging both after the influence of standard liquids. T2 - 18th IAPRI World packaging conference CY - San Luis Obispo, CA, USA DA - 17.06.2012 KW - Wall thickness KW - Internal pressure test KW - Finite element KW - Simulation KW - Jerrycan PY - 2013 DO - https://doi.org/10.1002/pts.1983 SN - 0894-3214 VL - 26 IS - 6 SP - 311 EP - 326 PB - Wiley CY - Chichester, UK AN - OPUS4-29282 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Witt, Klaus A1 - Cui, G. A1 - Luo, M.R. A1 - Rigg, B. A1 - Roesler, G. T1 - Uniform Colour Spaces Based on the DIN99 Colour-Difference Formula N2 - Several colour-difference formulas such as CMC, CIE94, and CIEDE2000 have been developed by modifying CIELAB. These formulas give much better fits for experimental data based on small colour differences than does CIELAB. None of these has an associated uniform colour space (UCS). The need for a UCS is demonstrated by the widespread use of the a*b* diagram despite the lack of uniformity. This article describes the development of formulas, with the same basic structure as the DIN99 formula, that predict the experimental data sets better than do the CMC and CIE94 colour-difference formulas and only slightly worse than CIEDE2000 (which was optimized on the experimental data). However, these formulas all have an associated UCS. The spaces are similar in form to L*a*b*. © 2002 Wiley Periodicals, Inc. Col Res Appl, 27, 282-290, 2002; Published online in Wiley InterScience (www.interscience.wiley.com). KW - DIN99-Farbabstandsformel KW - Uniform colour space KW - Colour-difference metrics KW - Colour discrimination ellipses PY - 2002 DO - https://doi.org/10.1002/col.10066 SN - 0361-2317 SN - 1520-6378 VL - 27 IS - 4 SP - 282 EP - 290 PB - Wiley CY - New York, NY AN - OPUS4-1417 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Pistol, Klaus A1 - Huismann, S. A1 - Diederichs, U. A1 - Pimienta, P. A1 - Jumppanen, U.M. A1 - Mindeguia, J.C. T1 - Stress-strain-relation, compressive strength and modulus of elasticity N2 - This chapter report the most recent experimental results on mechanical behaviour at high temperature of high-performance concretes. After a short introduction, subsection 5.2 describes the main testing methods that were used in the analysed studies. Sub-section 5.3 collects and compares; the temperature-dependency of the compressive strength and modulus of elastici1ty of many experimental studies. The influence of parameters such as the initial compressive strength, the type of aggregate, the presence of additions, the W/C ratio, the moishrre content and the way the mechanical test was performed is analysed. Sub-section 5.4 presents the experimental results obtained under a constant temperature, i.e. creep tests at high temperature. Sub-section 5.5 presents experimental results obtained under increasing temperahrre. These results allow assessing the free thennal strain of concrete (when no mechanical load is applied) and the so-called "transient the1mal strain". Finally, subsection 5.6 collects and analyses the few results conceming the temperature-dependency of the tensile strength of high-perfo1mance concretes. KW - Stress-strain-relation KW - High temperature PY - 2019 SN - 978-3-319-95431-8 SN - 978-3-319-95432-5 SN - 2213-204X SN - 2213-2031 SP - 89 EP - 105 PB - Springer CY - Swizerland AN - OPUS4-47212 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -