TY - JOUR A1 - Zeleny, R. A1 - Voorspoels, S. A1 - Ricci, M. A1 - Becker, Roland A1 - Jung, Christian A1 - Bremser, Wolfram A1 - Sittidech, M. A1 - Panyawathanakit, N. A1 - Wong, W. F. A1 - Choi, S.M. A1 - Lo, K.C. A1 - Yeung, W. Y. A1 - Kim, D.H. A1 - Han, J. A1 - Ryu, J. A1 - Mingwu, S. A1 - Chao, W. A1 - Schantz, M.M. A1 - Lippa, K.A. A1 - Matsuyama, S. T1 - Evaluation of the state-of-the-art measurement capabilities for selected PBDEs and decaBB in plastic by the international intercomparison CCQM-P114 JF - Analytical and bioanalytical chemistry N2 - An international intercomparison involving eight national metrology institutes (NMIs) was conducted to establish their current measurement capabilities for determining five selected congeners from the brominated flame retardant classes polybrominated diphenyl ethers and polybrominated biphenyls. A candidate reference material consisting of polypropylene fortified with technical mixtures of penta-, octa- and decabromo diphenyl ether and decabromo biphenyl, which was thoroughly assessed for material homogeneity and stability, was used as study material. The analytical procedures applied by the participants differed with regard to sample pre-treatment, extraction, clean-up, employed calibrants and type of calibration procedure as well as regarding analytical methods used for separation, identification and quantification of the flame retardant congeners (gas chromatography coupled to an electron capture detector (GC-ECD), gas chromatography-mass spectrometry in the electron ionisation mode (GC-EI-MS), gas chromatography-mass spectrometry in the electron capture negative ionisation mode (GC-ECNI-MS), and liquid chromatography-inductive coupled plasma-mass spectrometry (LC-ICP-MS)). The laboratory means agreed well with relative standard deviations of the mean of means of 1.9%, 4.8%, 5.5% and 5.4% for brominated diphenyl ether (BDE) 47, 183 and 209 and for the brominated biphenyl (BB) congener 209, respectively. For BDE 206, a relative standard deviation of 28.5% was obtained. For all five congeners, within-laboratory relative standard deviations of six measurements obtained under intermediate precision conditions were between 1% and 10%, and reported expanded measurements uncertainties typically ranged from 4% to 10% (8% to 14% for BDE 206). Furthermore, the results are in good agreement with those obtained in the characterization exercise for determining certified values for the flame retardant congeners in the same material. The results demonstrate the state-of-the-art measurement capabilities of NMIs for quantifying representative BDE congeners and BB 209 in a polymer. The outcome of this intercomparison (pilot study) in conjunction with possible improvements for employing exclusively calibrants with thoroughly assessed purity suggests that a key comparison aiming at underpinning calibration and measurement capability (CMC) claims of NMIs can be conducted. KW - Flame retardants KW - Polymer KW - Polybrominated diphenyl ethers (PBDEs) KW - Polybrominated biphenyls (PBBs) KW - International intercomparison PY - 2010 DO - https://doi.org/10.1007/s00216-009-3314-7 SN - 1618-2642 SN - 1618-2650 VL - 396 IS - 4 SP - 1501 EP - 1511 PB - Springer CY - Berlin AN - OPUS4-22905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhou, Z. A1 - Han, Q. A1 - Wang, D. A1 - Macé, T. A1 - Kipphardt, Heinrich A1 - Maiwald, Michael A1 - Tuma, Dirk A1 - Uehara, S. A1 - Akima, D. A1 - Shimosaka, T. A1 - Jung, J. A1 - Oh, S.-H. A1 - van der Veen, A. A1 - van Wijk, J.I.T. A1 - Ziel, P. R. A1 - Konopelko, L. A1 - Valkova, M. A1 - Mogale, D.M. A1 - Botha, A. A1 - Brewer, P. A1 - Murugan, A. A1 - Minnaro, M.D. A1 - Miller, M. A1 - Guenther, F. A1 - Kelly, M.E. T1 - CCQM K101 Final report international comparison CCQM-K101:Oxygen in nitrogen-a track B comparison and that the matrix contains argon JF - Metrologia N2 - This key comparison aims to assess the capabilities of the participants to determine the amount-of-substance fraction oxygen in nitrogen. The GAWG has classified this as a track B comparison, due to the unexpected 50 μmol/mol argon mole fraction content of the transfer standards, which effects the achievable performance of some measurement techniques such a GC-TCD. The separation of oxygen and argon is challenging, and not all systems in use are equally well designed for it. As this analytical challenge due to a substantial fraction of argon in the transfer standards became a reality, the Gas Analysis Working Group (GAWG) decided to qualify this key comparison as a regular key comparison and not as a core comparison, which may be used to support calibration and measurement capabilities (CMCs) for oxygen in nitrogen, or for oxygen in nitrogen mixtures containing argon only (see also the section on support to CMCs). KW - CCQM-K101 KW - Gas analysis PY - 2016 UR - http://iopscience.iop.org/article/10.1088/0026-1394/53/1A/08013 SN - 1681-7575 SN - 0026-1394 VL - 53 IS - Techn Suppl SP - 08013, 1 EP - 71 PB - IOP publishing AN - OPUS4-40013 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kraus, Werner A1 - Walther, M. A1 - Jung, C. M. A1 - Emmerling, Franziska A1 - Pietzsch, H.-J. T1 - Bromotricarbonyl{15-[2-(methylsulfanyl)ethylsulfanyl]pentadecanoic acid-kappa2S,S'}rhenium(I) JF - Acta crystallographica E N2 - The title compound, [ReBr(C18H36O2S2)(CO)3], was synthesized and characterized as a non-radioactive surrogate of a novel Tc-containing fatty acid derivative prepared according to the tricarbonyl/dithioether design with the objective of developing new Tc-based radiopharmaceuticals for the non-invasive diagnosis of myocardial metabolism. The Re chelate contains the metal in the oxidation state +1 and is attached to the terminal position of a fatty acid. The complex formation was accomplished by a ligand exchange reaction using [NBu4]2[Re(CO)3Br3] as starting material. KW - Fatty acid KW - Tc-compound KW - Radio-pharmaceutical PY - 2006 DO - https://doi.org/10.1107/S1600536806024081 SN - 1600-5368 VL - 62 IS - 7 SP - m1660 EP - m1662 PB - Munksgaard CY - Copenhagen AN - OPUS4-12529 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tisato, F. A1 - Refosco, F. A1 - Porchia, M. A1 - Bolzati, C. A1 - Bandoli, G. A1 - Dolmella, A. A1 - Duatti, A. A1 - Boschi, A. A1 - Jung, C. M. A1 - Pietzsch, H.-J. A1 - Kraus, Werner T1 - The Crucial Role of the Diphosphine Heteroatom X in the Stereochemistry and Stabilization of the Substitution-Inert [M(N)(PXP)]2+ Metal Fragments (M = Tc, Re; PXP = Diphosphine Ligand) JF - Inorganic Chemistry N2 - The nature of the heteroatom X incorporated in the five-membered PXP-diphosphine bridging chain was found to play a primary unit role both in the overall stability and in the stereochemical arrangement of nitrido-containing [M(N)(PXP)]2+ metal fragments (M = Tc, Re). Thus, by mixing PXP ligands with labile [Re(N)Cl4]- and Tc(N)Cl2(PPh3)2 nitrido precursors in CH2Cl2/MeOH mixtures, a series of neutral M(N)Cl2(PXP) complexes (M = Tc, 1-5; M = Re, 8, 9) was collected. In the resulting distorted octahedrons, PXP adopted facial or meridional coordination, and combination with halide co-ligands produced three different stereochemical arrangements, that is, fac,cis, mer,cis, and mer,trans, depending primarily on the nature of the diphosphine heteroatom X. When X = NH, mer,cis-Tc(N)Cl2(PNP1), 1, was the only isomer formed. Alternatively, when a tertiary amine nitrogen (X = NR; R = CH3, CH2CH2OCH3) was introduced in the bridging chain, fac,cis-M(N)Cl2(PN(R)P) complexes (M = Tc, 2, 3; M = Re, 8f) were obtained. Isomerization into the mer,cis-Re(N)Cl2(PN(R)P), 8m, species was observed only in the case of rhenium when the tertiary amine group carried the less encumbering methyl substituent. fac,cis-Tc(N)Cl2(PSP), 4f, was isolated in the solid state when X = S, but a mixture of fac,cis-Tc(N)Cl2(PSP) and mer,trans-Tc(N)Cl2(PSP), 4m, isomers was found in equilibrium in the solution state. A similar equilibrium between fac,cis-M(N)Cl2(POP) (M = Tc, 5f; M = Re, 9f) and mer,trans-M(N)Cl2(POP) (M = Tc, 5m; M = Re, 9m) species was detected in POP-containing complexes. The molecular structure of all of these complexes was assessed by means of conventional physicochemical techniques including multinuclear NMR spectroscopy and X-ray diffraction analysis of representative mer,cis-Tc(N)Cl2(PN(H)P), 1, fac,cis-Tc(N)Cl2(PSP), 4f, and mer,cis-Re(N)Cl2(PN(Me)P), 8m, compounds. PY - 2004 DO - https://doi.org/10.1021/ic049139r SN - 0020-1669 SN - 1520-510X VL - 43 IS - 26 SP - 8617 EP - 8625 PB - American Chemical Society CY - Washington, DC AN - OPUS4-5546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walther, M. A1 - Jung, C. M. A1 - Bergmann, R. A1 - Pietzsch, J. A1 - Rode, K. A1 - Fahmy, K. A1 - Mirtschink, P. A1 - Stehr, S. A1 - Heintz, A. A1 - Wunderlich, G. A1 - Kraus, Werner A1 - Pietzsch, H.-J. A1 - Kropp, J. A1 - Deussen, A. A1 - Spies, H. T1 - Synthesis and Biological Evaluation of a New Type of 99mTechnetium-Labeled Fatty Acid for Myocardial Metabolism Imaging JF - Bioconjugate chemistry PY - 2007 SN - 1043-1802 SN - 1520-4812 VL - 18 SP - 216 EP - 230 CY - Washington, DC AN - OPUS4-14514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulze, M. A1 - Neugebauer, M. A1 - Meeß, R. A1 - Brzoska, J. A1 - Jung, A. A1 - Staude, Andreas A1 - Ehrig, Karsten T1 - Der Einfluss unterschiedlicher Materialzusammensetzungen auf das dimensionelle Messen von Mikroobjekten mittels Mikro-Computertomographie T2 - DGZfP-Jahrestagung 2010 N2 - Computertomographische Aufnahmen von Objekten mit stark voneinander abweichenden Absorptionseigenschaften stellen sowohl für den Anwendungsbereich der zerstörungsfreien Prüfung als auch für den der dimensionellen Messtechnik eine besondere Herausforderung dar. Die Aufnahmekonfiguration kann bei Objekten dieser Art häufig nicht so gewählt werden, dass die unterschiedlichen Materialeigenschaften mit ausreichender Qualität abgebildet werden können. Aus diesem Grund ist eine objektive Bewertung der Oberflächenmessung mit Hilfe eines in dieser Untersuchung eingeführten Qualitätsmaßes erforderlich. Anhand der in dieser Arbeit vorgestellten Prüfkörperserie soll der Einfluss der Materialzusammensetzung auf das dimensionelle Messen mit CT erfasst und charakterisiert werden. Unter Berücksichtigung der Qualitätsbewertung der Oberflächenpunkte erfolgt die Berechnung der Form- und Abstandsabweichungen. Ziel ist es, die Genauigkeit der Oberflächenmessung hinsichtlich unterschiedlicher Aufnahmeparameter und Materialzusammensetzungen darzustellen. Anhand dieser Ergebnisse ist es möglich, den computertomographischen Aufnahme- und Auswertungsprozess quantitativ zu bewerten und Ursachen der Abweichungen zu diskutieren. T2 - DGZfP-Jahrestagung 2010 CY - Erfurt, Deutschland DA - 2010-05-10 PY - 2010 UR - http://www.ndt.net/article/dgzfp2010/Inhalt/di2a4.pdf SN - 978-3-940283-26-9 IS - DGZfP-BB 122 (Di.2.A.4) SP - 1 EP - 9 CY - Berlin AN - OPUS4-22528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schubnell, J. A1 - Konidena, S. K. A1 - Jung, M. A1 - Braun, M. A1 - Ehlers, S. A1 - Madia, Mauro A1 - Kannengießer, Thomas A1 - Löschner, D. T1 - Approach for the probabilistic fatigue assessment of welded joints based on the local geometry of the weld seam JF - Fatigue and Fracture Engineering Materials and Structures N2 - Welded joints show large variation of the weld toe geometry along the weld seam, which is one important reason for the comparably large scatter in fatigue life. Therefore, it is crucial to take the local geometry at the weld toe into account, to reduce the conservatism in fatigue assessment of welded joints. This study is based on the IBESS procedure for the calculation of the fatigue strength, whereby the evaluation of local geometrical parameters is carried out by means of 3D surface scans. The approach is validated against 26 fatigue test series. The fatigue life is in general overpredicted, whereas good agreement is achieved for high stress ratio (R = 0.5). A sensitivity analysis conducted with IBESS shows that weld toe radii ρ < 2 mm and flank angle α < 30° have a significant influence on the calculated fatigue strength. In contrast to this, no strong correlation between ρ and the fatigue strength was determined experimentally in this study. KW - 3D Scanning KW - Fatigue Strength KW - Fracture Mechanics KW - IBESS Approach KW - Local Weld Geometry KW - Welded Joints PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-585700 DO - https://doi.org/10.1111/ffe.14170 SN - 8756-758X SP - 1 EP - 20 PB - Wiley AN - OPUS4-58570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jung, C. M. A1 - Heintz, A. A1 - Kraus, Werner A1 - Wunderlich, G. A1 - Leibnitz, Peter A1 - Pietzsch, H.-J. A1 - Kropp, J. A1 - Deussen, A. A1 - Spies, H. ED - Marino, N. T1 - Technetium- and Rhenium-Labelled Fatty Acids as Model Compounds for Myocardial Metabolism Imaging T2 - Proceedings of the Sixth International Symposium on Technetium in Chemistry and Nuclear Medicine N2 - In an attempt to develop new technetium-based radiopharmaceuticals for the non-invasive diagnosis of oxidative myocardial metabolism, rhenium model compounds according to the ‚3+1' mixed ligand approach as well as the organometallic tricarbonyl-design were synthesized. The geometrical impact of different chelates on the integrity of the fatty acid head structure was determined by single crystal X-ray analyses. To evaluate the diagnostic potential of the analogous Technetium-99m compounds, fatty acid complexes of the ‚3+1' mixed ligand type were prepared on n.c.a.-level and studied in the isolated constant-flow-perfused guinea pig heart model; compared to established [123I]Iodine-labelled fatty acid radiotracers, the tested Technetium-99m derivatives showed a specific, however significantly lower myocardial extraction rate. T2 - 6th International Symposium on Technetium in Chemistry and Nuclear Medicine CY - Bressanone, Italy DA - 2002-09-04 KW - Fatty acids KW - Metabolism KW - Myocardial Imaging KW - Rhenium KW - Technetium-99m PY - 2002 UR - http://www.fzd.de/db/!Publications?pSelYear=2002&pLang=en&pNid=0&pSelWithSubmitted=0&pSelSort=TITEL&pSelPublForm=4&pSelPage=2 SN - 88-86281-73-0 N1 - Serientitel: Technetium, rhenium and other metals in chemistry and nuclear medicine – Series title: Technetium, rhenium and other metals in chemistry and nuclear medicine VL - 6 IS - 6 SP - 443 EP - 445 PB - SGEditoriali CY - Padova AN - OPUS4-1999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jung, C. M. A1 - Kraus, Werner A1 - Leibnitz, Peter A1 - Pietzsch, H.-J. A1 - Kropp, J. A1 - Spies, H. T1 - Synthesis and First Crystal Structure of Rhenium Complexes derived from omega-Functionalized Fatty Acids as Model Compounds of Technetium Tracers for Myocardial Metabolism Imaging JF - European journal of inorganic chemistry N2 - In an attempt to develop new technetium-based radiopharmaceuticals for the noninvasive diagnosis of myocardial metabolism, we have synthesized three examples of novel metal-containing fatty acid derivatives according to the 3+1 mixed-ligand and the Schiff base/tricarbonyl design. The chelates contain the metal core in the oxidation states +5 and +1, respectively, and are attached to the end-position of a fatty acid chain. The complex formation was accomplished by ligand-exchange reactions with three different rhenium precursors, whereas the inactive rhenium metal was utilized as a surrogate of the technetium radionuclide. The molecular structures of the fatty acid complexes 7, 10 and 14 were determined by single-crystal X-ray diffraction analyses and impressively show a general problem in technetium tracer research, namely the significant structural alterations of bioactive molecules by coordination even to small metal chelates. KW - Rhenium KW - Technetium KW - Fatty acids KW - Drug research KW - Radiopharmaceuticals PY - 2002 DO - https://doi.org/10.1002/1099-0682(200205)2002:5<1219::AID-EJIC1219>3.0.CO;2-N SN - 1434-1948 SN - 1099-0682 VL - 2002 IS - 5 SP - 1219 EP - 1225 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-1552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Renz, F. A1 - Zaba, C. A1 - Roßberg, L. A1 - Jung, S. A1 - Klein, M. A1 - Klingelhöfer, G. A1 - Wünsche, A. A1 - Reinhardt, S. A1 - Menzel, Michael T1 - Spin transition in heptanuclear star-shaped iron(III)-antimony(V) NCS- and CN-bridged compounds JF - Polyhedron N2 - The precursor [FeIII(L)Cl] (LH2 = N,N'-bis(2'-hydroxy-benzyliden)-1,6-diamino-3-azahexane) has been prepared and Mössbauer spectroscopy assigned a high-spin (S = 5/2) state at room temperature. The precursor is combined with the bridging units [SbV(X)6]- (X = CN-, NCS-) to yield star-shaped heptanuclear clusters [(LFeIII-X)6SbV]Cl5. The star-shaped compounds are in general high-spin systems at room temperature. On cooling to 20 K some of the iron(III) centers switch to the low-spin state as indicated by Mössbauer spectroscopy, i.e. multiple electronic transitions. While the cyano-bridged complex performs a multiple spin transition the thiocyanate-compound shows no significant population at both temperatures. KW - Heptanuclear KW - High-spin molecule KW - SbV KW - Multistability KW - Multiple spin transition PY - 2009 DO - https://doi.org/10.1016/j.poly.2008.12.027 SN - 0277-5387 VL - 28 IS - 9-10 SP - 2036 EP - 2038 PB - Elsevier CY - Amsterdam [u.a.] ; Jena AN - OPUS4-19659 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jung, S. A1 - Renz, F. A1 - Klein, M. A1 - Menzel, Michael A1 - Boca, R. A1 - Stößer, R. T1 - Molecular switching in iron complexes bridged via tincyanides observed by Mössbauer and ESR spectroscopy JF - Journal of physics / Conference series N2 - The precursor [FeIII(L)Cl] (LH2 = N,N'-bis(2'-hydroxy-3'-X-benzyliden)-1,6-diamino-3-N-hexane) is a high-spin (S = 5/2) complex (with X = -CH3, -O-CH3). This precursor is combined with the bridging unit [SnIV(CN)4] to yield star-shaped pentanuclear clusters, [(L-X-FeIII)4Sn(CN)4]Cl4 57Fe-Mössbauer, 119mSn-Mössbauer, and ESR spectroscopy are used to study our samples. For X = -CH3 the 57Fe-Mössbauer data show a multiple spin transition between iron(III) in the high-spin and low-spin state. Changing the functional group from X = -CH3 to X = -O-CH3 turns the switchability off. KW - Switching iron complexes KW - Spin-transition KW - Mössbauer spectroscopy KW - ESR-spectroscopy PY - 2010 DO - https://doi.org/10.1088/1742-6596/217/1/012027 SN - 1742-6588 SN - 1742-6596 VL - 217 IS - 1 / 012027 SP - 1 EP - 6 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-22561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hiebl, B. A1 - Ascher, Lena A1 - Luetzow, K. A1 - Kratz, K. A1 - Gruber, C. A1 - Mrowietz, C. A1 - Nehring, M. E. A1 - Lendlein, A. A1 - Franke, R.- P. A1 - Jung, F. T1 - Albumin solder covalently bound to a polymer membrane: New approach to improve binding strength in laser tissue soldering in-vitro JF - Clinical Hemorheology and Microcirculation N2 - Laser tissue soldering (LTS) based on indocyanine green (ICG)-mediated heat- denaturation of proteins might be a promising alternative technique for micro-suturing, but up to now the Problem of too weak shear strength of the solder welds in comparison to sutures is not solved. Earlier reports gave promising results showing that solder supported by carrier materials can enhance the cohesive strength of the liquid solder. In these studies, the solder was applied to the carriers by dip coating. Higher reliability of the connection between the solder and the carrier material is expected when the solder is bound covalently to the carrier material. In the present study a poly(ether imide) (PEI) membrane served as carrier material and ICG- supplemented albumin as solder substrate. The latter was covalently coupled to the carrier membrane under physiological conditions to prevent structural protein changes. As laser source a diode continuous-wave laser emitting at 808 nm with intensities between 250mW and 1500mW was utilized. The Albumin functionalized carrier membrane was placed onto the tunica media of explanted pig thoracic aortae forming an overlapping area of approximately 0.5×0.5 cm2. All tests were performed in a dry state to prevent laser light absorption by water. Infrared spectroscopy, spectro-photometrical determination of the secondary and Primary amine groups after acid orange II staining, contact angle measurements, and atomic force microscopy proved the successful functionalization of the PEI membrane with albumin. A laser power of 450mW LTS could generate a membrane-blood vessel connection which was characterized by a shear strength of 0.08±0.002MPa, corresponding to 15% of the tensile strength of the native blood vessel. Theoretically, an overlapping zone of 4.1mmaround the entire circumference of the blood vessel could have provided shear strength of the PEI membrane-blood vessel compound identical to the tensile strength of the native blood vessel. These in-vitro results confirmed the beneficial effects of solder reinforcement by carrier membranes, and suggest LTS with covalently bound solders on PEI substrates for further studies in animal models. KW - Tissue soldering KW - Albumin KW - Polymer membrane KW - Laser PY - 2018 DO - https://doi.org/10.3233/CH-189108 SN - 1386-0291 SN - 1875-8622 VL - 69 IS - 1-2 SP - 317 EP - 326 PB - IOS Press AN - OPUS4-45149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Park, J. A1 - Kim, G. B. A1 - Lippitz, Andreas A1 - Kim, Y. M. A1 - Jung, D. A1 - Unger, Wolfgang A1 - Kim, Y.-P. A1 - Lee, T. G. T1 - Plasma-polymerized antifouling biochips for label-free measurement of protease activity in cell culture media JF - Sensors & Actuators: B. Chemical N2 - We report polyethylene glycol (PEG)-grafting antifouling surfaces using a plasma copolymerized (PcP) technique to monitor protease activity in complex media. By varying the mixing ratio of the PEG and ethylenediamine (EDA) precursors, the PcP-PEG-EDA (PcP-PE) film was able to easily control surface amine density with good preservation of the internal PEG structure. We found that nonspecific protein adsorption was dramatically reduced in serum-containing media on the PcP-PE films, as opposed to that on plasma polymerized-EDA (PP-E) films without PEG. When SPR sensor chips coated with PcP-PE film were employed to detect protease activity, biotinylated luciferase probes (luciferase-peptide-biotin) on streptavidin-conjugated SPR chips enabled real-time and label-free measurement of matrix metalloproteinase activity in cell culture media. Owing to its excellent antifouling ability, this newly developed method boasts minimal nonspecific binding and can serve as a biochip platform to promote a wide range of applications in the biological field. KW - Polyethylene glycol (PEG)-grafting antifouling surface KW - Biochip KW - ATR-FTIR spectroscopy KW - XPS KW - NEXAFS KW - Plasma PY - 2019 DO - https://doi.org/10.1016/j.snb.2018.10.123 SN - 0925-4005 VL - 281 SP - 527 EP - 534 PB - Elsevier B.V. AN - OPUS4-46463 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Renz, F. A1 - Jung, S. A1 - Klein, M. A1 - Menzel, Michael A1 - Thünemann, Andreas T1 - Molecular switching complexes with iron and tin as central atom JF - Polyhedron N2 - The precursor [FeIII(L)Cl] (LH1.5) and several reactive groups for surface anchoring, full surface shielding can be reached, which leads to reduced protein adsorption of albumin and fibrinogen. In addition, adherent thrombocytes were not activated. This could be clearly shown by immunostaining adherent proteins and analyzing the thrombocyte covered area. The presented work provides an important strategy for the development of application relevant hemocompatible 3D structured materials. KW - Nanotechnology KW - thrombocyte adhesion KW - biomedical applications PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-308196 DO - https://doi.org/10.1039/c4tb00184b SN - 2050-750X SN - 2050-7518 VL - 2 IS - 23 SP - 3626 EP - 3635 PB - Royal Soc. of Chemistry CY - Cambridge AN - OPUS4-30819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -