TY - JOUR A1 - Ickert, Stefanie A1 - Hofmann, J. A1 - Riedel, Jens A1 - Beck, S. A1 - Pagel, K. A1 - Linscheid, M. W. T1 - Charge-induced geometrical reorganization of DNA oligonucleotides studied by tandem mass spectrometry and ion mobility N2 - Mass spectrometry is applied as a tool for the elucidation of molecular structures. This premises that gas-phase structures reflect the original geometry of the analytes, while it requires a thorough understanding and investigation of the forces controlling and affecting the gas-phase structures. However, only little is known about conformational changes of oligonucleotides in the gas phase. In this study, a series of multiply charged DNA oligonucleotides (n¼15–40) has been subjected to a comprehensive tandem mass spectrometric study to unravel transitions between different ionic gas-phase structures. The nucleobase sequence and the chain length were varied to gain insights into their influence on the geometrical oligonucleotide organization. Altogether, 23 oligonucleotides were analyzed using collision-induced fragmentation. All sequences showed comparable correlation regarding the characteristic collision energy. This value that is also a measure for stability, strongly correlates with the net charge density of the precursor ions. With decreasing charge of the oligonucleotides, an increase in the fragmentation energy was observed. At a distinct charge density, a deviation from linearity was observed for all studied species, indicating a structural reorganization. To corroborate the proposed geometrical change, collisional cross-sections of the oligonucleotides at different charge states were determined using ion mobility-mass spectrometry. The results clearly indicate that an increase in charge density and thus Coulomb repulsion results in the transition from a folded, compact form to elongated structures of the precursor ions. Our data show this structural transition to depend mainly on the charge density, whereas sequence and size do not have an influence. KW - Ion mobility KW - Collision-induced dissociation KW - Mass spectrometry KW - Oligonucleotide KW - Fragmentation KW - Tandem-MS PY - 2018 DO - https://doi.org/10.1177/1469066717746896 SN - 1469-0667 SN - 1751-6838 VL - 24 IS - 2 SP - 225 EP - 230 PB - Sage AN - OPUS4-44429 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Heidenreich, F. A1 - Herten, M. T1 - Verwendung faseroptischer Messtechnik im Zuge wiederholter Eignungsprüfungen an Verpressankern N2 - Im Rahmen des Ausbaus des Dortmund-Ems-Kanals wurden an der Schleuse Gleesen Forschungsanker installiert, die Rückschlüsse auf das Tragverhalten in Folge des chemischen Angriffs kalklösender Kohlensäure geben sollen. Die Forschungsanker werden seit der Erstellung im Jahr 2017 mit verteilter faseroptischer Sensorik während der jährlichen Eignungsprüfungen untersucht. Die Ergebnisse der Jahre 2017 bis 2019 werden im Folgenden dargestellt. T2 - Messen in der Geotechnik 2020 CY - Braunschweig, Germany DA - 20.02.2020 KW - Faseroptische Sensorik KW - Rayleigh Rückstreuung KW - Verpressanker KW - Chemischer Angriff KW - Rissbildung PY - 2020 SN - 978-3-948141-02-8 DO - https://doi.org/10.24355/dbbs.084-201912181435-0 IS - 110 SP - 297 EP - 323 AN - OPUS4-51687 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Przondziono, R. A1 - Timothy, J. J. A1 - Weise, Frank A1 - Krütt, Enno A1 - Breitenbücher, R. A1 - Meschke, G. A1 - Hofmann, M. T1 - Degradation in concrete structures due to cyclic loading and its effect on transport processes - Experiments and modeling N2 - According to the objectives of the research group 1498, this paper deals with degradation effects in concrete structures that are caused by cyclic flexural loading. The goal is to determine their influence on the fluid transport processes within the material on the basis of experimental results and numerical simulations. The overall question was, to which extent the ingress of externally supplied alkalis and subsequently an alkali-silica reaction are affected by such modifications in the microstructure. Degradation in the concrete microstructure is characterized by ultrasonic wave measurements as well as by microscopic crack analysis. Furthermore, experiments on the penetration behavior of water into the investigated materials were performed. The penetration behavior into predamaged concrete microstructures was examined by the classical Karsten tube experiment, nuclear magnetic resonance method, and time domain reflectometry techniques. In order to create an appropriate model of the material's degradation on the water transport, the Darcy law was applied to describe the flow in partially saturated concrete. Material degradation is taken into account by an effective permeability that is dependent on the state of degradation. This effective permeability is obtained by the micromechanical homogenisation of the flow in an Representative Elementary Volume (REV) with distributed ellipsoidal microcracks embedded in a porous medium. The data gained in the microscopic crack analysis is used as input for the micromechanical model. Finite element simulations for unsaturated flow using the micromechanical model were compared with the experimental results showing good qualitative and quantitative agreement. KW - Alkali ingress KW - Alkali-silica reaction KW - Computational model for unsaturated flow KW - Cyclic loading KW - Degradation KW - Micromechanics model KW - Transport processes PY - 2017 DO - https://doi.org/10.1002/suco.201600180 SN - 1751-7648 SN - 1464-4177 VL - 18 IS - 4 SP - 519 EP - 527 PB - Ernst & Sohn AN - OPUS4-41008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, M. A1 - Kubowitz, P. A1 - Hofmann, Detlef ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Scale of intelligence in hybrid bridge structures - new aspects of monitoring by using fibre-optic sensors in timber elements N2 - In structural engineering timber is appreciated due to its low weight, its high aesthetic quality and because it is a renewable resource. The market share of timber structures and wood based hybrid structures will clearly increase over the next few years due to greater environmental awareness and a higher demand for sustainability. However, building with timber is marked by characteristics which lead to significant disadvantages in comparison wifh technical materials. For example, in outdoor areas Chemical and structural approaches offen lead to unsatisfactory and expensive Solutions with respect to durability. An idea is to make natural lumber a high-performance material which can be designed to meet the engineers’ demands conceming strength, stiffness, durability, shape, safety etc. These changes can affect the material itself, new technologies or a new approach to monitoring. Especially hybrids made of common timber products and technical textiles or enhanced timber products are high-capacitive and reach high bearing strengths with low material input and good durability. These hybrids are particularly qualified to use the advantages of wood and minimize the disadvantages. They can be used in different ways for load bearing structures, i.e. bridges. New construction types need monitoring to observe the stress and strains for which they were designed, and the structures’ behaviour as well as to guarantee required safety levels. The aim of successful usage of fibre optic measurement technology in timber elements was the development of a technology for measuring the lengthening in timber elements and wood based hybrid elements by using fibre optic sensors. The scientific and technical challenge was to develop an applicationtechnology for optical glass fibres in timber and densified veneer wood. In laboratory tests as well as with the erection of a footbridge and during in-situ tests it could be shown that the structurally integrated fibre optic sensor technology used is suitable for short and long term measurement. The developed embedment technology tums out to be practical and fit for good transfer of strain-values from timber to the modified sensor fibres. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Structural health monitoring KW - Structural engineering KW - Timber KW - Composites KW - Hybrid construction types KW - Fibre optic sensor technology KW - Sensor fibres PY - 2013 SN - 978-962-367-768-4 SP - 1 EP - 10 AN - OPUS4-29913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schallert, M. A1 - Hofmann, Detlef A1 - Habel, Wolfgang T1 - Strukturanalyse von Betonpfählen durch eingebettete faseroptische Sensoren N2 - Zur Gründung von Bauwerken auf weichen, gering tragfähigen Böden werden unter anderem Betonpfähle, einzeln oder in Pfahlgruppen, eingesetzt. Deren Bewertung bzgl. Tragverhalten bzw. Integrität ist bei bestimmten Baugrundverhältnissen und Pfahlgeometrien schwierig. Hierfür werden statische und dynamische Pfahlprüfungen durchgeführt. Aus Messwerten vom Pfahlkopf bzw. vom oberen Pfahlbereich werden üblicherweise die notwendigen Aussagen abgeleitet. Eine genauere Bewertung ist möglich, wenn präzise Messwerte über die gesamte Pfahllänge vorliegen. Deshalb wurden hochauflösende betoneinbettbare Messwertaufnehmer auf Basis von Faser-Fabry-Perot-Sensoren entwickelt, die in Modell- und in realen Rammpfählen getestet wurden. Der Beitrag beschreibt den Sensor, die Installation und exemplarisch einige Testergebnisse zur Erfassung der Wellenausbreitung im Modellpfahl. Feldtests wurden zurzeit der Erstellung des Manuskripts erfolgreich begonnen. Reinforced concrete piles are often used for structures on non-sufficiently bearing soil areas. Assessment of bearing capacity and bearing behaviour of large concrete piles remains a difficult task under specific soil conditions and pile geometries. Usually static and dynamic pile tests are carried out for quality assurance. From dynamic measurements taken only from the pile head, the bearing behaviour and structural integrity can be derived using the one-dimensional theory of wave propagation. More precise information about the pile features can be achieved by highly resolving fibre-optic sensors based on Fabry-Perot technology, distributed over several locations along the pile length. Small scale piles and real driven piles have been tested. This paper describes the sensor, the sensor installation, and experimental results of tests in laboratory as well as test results for recording the wave propagation in the small scale piles. KW - Eingebetteter faseroptischer Sensor KW - Fabry-Perot-Sensor KW - Tragverhalten KW - Integritätstest KW - Embedded fiber-optic sensor KW - Low-strain pile integrity tests PY - 2008 DO - https://doi.org/10.1524/teme.2008.0867 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 75 IS - 9 SP - 485 EP - 500 PB - Oldenbourg CY - München AN - OPUS4-18041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hölck, Ole A1 - Heuchel, M. A1 - Böhning, Martin A1 - Hofmann, D. T1 - Simulation of Experimentally Observed Dilation Phenomena During Integral Gas Sorption in Glassy Polymers N2 - A molecular modeling investigation of dilation effects induced by sorbed gas molecules in two glassy polymers is presented. As experimental reference, integral sorption of CO2 and CH4 was measured for polysulfone (PSU) and a polyimide (6FDA-TrMPD, PI4) at 308 K and a pressure of 10 bar. Simultaneously, the gas induced swelling effect was measured with a dilatometer based on a capacitive distance sensor recorded. The experimental evidence of the (on the observed time scale and concentration levels) elastic nature of the gas induced dilation is supported by the dilation and contraction behavior observed in molecular dynamics (MD) simulations of respective detailed atomistic packing models. These models were constructed in accordance with gas concentration levels obtained from the experimental sorption results. Quantitative deviations between simulated and measured dilations are discussed as a consequence of an anelastic response of the polymer matrix which is too fast to be resolved in the experiments whose kinetics is dominated by diffusional processes. In the simulation, the initial insertion of penetrant molecules into equilibrated packing models circumvents the slow diffusional process of the experiment and allows a reasonable representation of the dilation process as well as a closer investigation. Our simulation approach reveals a different behavior for PSU and PI4 on the corresponding time scale. Most likely, the different chain mobility of the two polymers is responsible for the respective response to the inserted amount of gas molecules which is discussed in terms of the different chain mobilities of the two polymers. KW - Diffusion KW - Dilation KW - Gas sorption KW - Molecular modeling KW - Poly(ether sulfones) KW - Polyimides KW - Swelling PY - 2008 DO - https://doi.org/10.1002/polb.21342 SN - 0887-6266 SN - 1099-0488 VL - 46 IS - 1 SP - 59 EP - 71 PB - Wiley CY - Hoboken, NJ AN - OPUS4-16206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Hamann, M. A1 - Kubowitz, P. A1 - Habel, Wolfgang A1 - Hofmann, Detlef T1 - Hochleistungsholztragwerke - HHT - Entwicklung von hochbelastbaren Verbundbauweisen im Holzbau mit faserverstärkten Kunststoffen, technischen Textilien und Formpressholz - Aufstockung: Ersteinsatz von optischen Messfasern in Holzbauteilen KW - Holzbau KW - Hochleistungsholztragwerke KW - Verbundbauweise KW - Hybridbauteile KW - Faseroptische Sensorik KW - Faser-Bragg-Gitter KW - Optische Messverfahren KW - Monitoring KW - Brückenbau KW - Bauwerksüberwachung KW - Applizierungstechnologie PY - 2013 SN - 978-3-9815360-8-9 IS - BMBF-Vorhaben 0330722B SP - 1 EP - 103 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-27958 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Habel, Wolfgang A1 - Hofmann, Detlef A1 - Gutmann, Toivo A1 - Basedau, Frank A1 - Molter, M. A1 - Hegger, J. ED - Inaudi, D. T1 - Characterization of bond performance of textiles in cement matrices using fiber optic sensors T2 - Smart structures and materials 2002 - Smart sensor technology and measurement systems CY - San Diego, CA, USA DA - 2002-03-18 KW - Textile reinforced concrete KW - Fibers KW - Concrete KW - Bond KW - Fiber-optic sensors PY - 2002 SN - 0-8194-4442-1 DO - https://doi.org/10.1117/12.472626 SN - 1605-7422 N1 - Serientitel: SPIE proceedings series – Series title: SPIE proceedings series IS - 4694 SP - 253 EP - 258 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-1458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hofmann, Detlef A1 - Habel, Wolfgang A1 - Gutmann, Toivo A1 - Basedau, Frank A1 - Molter, M. A1 - Hegger, J. A1 - Will, N. T1 - Untersuchungen an textilbewehrtem Beton PY - 2002 SN - 0025-5300 VL - 44 IS - 5 SP - 194 EP - 198 PB - Carl Hanser Verlag CY - München AN - OPUS4-1474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Kohlhoff, Harald A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Habel, Wolfgang A1 - Baeßler, Matthias A1 - Niederleithinger, Ernst A1 - Georgi, Steven A1 - Herten, M. ED - Jaroszewicz, L.R. T1 - Static and dynamic pile testing of reinforced concrete piles with structure integrated fibre optic strain sensors N2 - Static and dynamic pile tests are carried out to determine the load bearing capacity and the quality of reinforced concrete piles. As part of a round robin test to evaluate dynamic load tests, structure integrated fibre optic strain sensors were used to receive more detailed information about the strains along the pile length compared to conventional measurements at the pile head. This paper shows the instrumentation of the pile with extrinsic Fabry-Perot interferometers sensors and fibre Bragg gratings sensors together with the results of the conducted static load test as well as the dynamic load Tests and pile integrity tests. T2 - EWOFS 2013 - 5th European workshop on optical fibre sensors CY - Kraków, Poland DA - 19.05.2013 KW - Static load test KW - Dynamic load test KW - Pile integrity test KW - Extrinsic Fabry-Perot interferometer KW - Fibre Bragg grating KW - Structure integrated sensor KW - Fibre optic strain sensor PY - 2013 SN - 978-0-81949-634-8 DO - https://doi.org/10.1117/12.2026813 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 8794 IS - Paper 8794 - 181 SP - 700 EP - 703 AN - OPUS4-28854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lay, Vera A1 - Effner, Ute A1 - Niederleithinger, Ernst A1 - Arendt, J. A1 - Hofmann, M. A1 - Kudla, W. T1 - Ultrasonic quality assurance at magnesia shotcrete sealing structures N2 - Engineered barriers are a key element to enable safe nuclear waste disposal. One method currently under research for their construction is magnesia concrete applied in a shotcrete procedure. In this study, the ultrasonic echo method is evaluated as a means for quality assurance. Imaging of internal structures (backwall, boreholes) and defects, such as delamination, has successfully been achieved in the shotcrete. Additionally, detailed information about the potential cause of selected reflectors are obtained by phase analysis. In several test blocks of various sizes, no consistent concrete section boundaries have been found by ultrasonic imaging, which was verified by subsequent drilling and complementary tests. An experiment with artificial defects imitating cracks, air-filled voids, and material with lower density has been challenging and shows the limitations of the current methods. Although significant defects, such as a large delamination, are reliably identified, several smaller defects are not identified. Generally, ultrasonic imaging provides a suitable base as a mean for quality assurance during and after the construction of sealing structures. However, further developments are required to enhance the reliability of the method and a full validation is still pending. Still, the method has potential to increase the safety of nuclear waste repositories. KW - Ultrasound KW - Imaging KW - Engineered barrier systems KW - Underground KW - Shotcrete PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-563170 DO - https://doi.org/10.3390/s22228717 SN - 1424-8220 VL - 22 IS - 22 SP - 1 EP - 16 PB - MDPI CY - Basel AN - OPUS4-56317 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Lay, Vera A1 - Effner, Ute A1 - Niederleithinger, Ernst A1 - Arendt, J. A1 - Hofmann, M. A1 - Kudla, W. T1 - Correction: Lay et al. Ultrasonic quality assurance at magnesia shotcrete sealing structures. Sensors 2022, 22, 8717 N2 - The authors wish to correct the following errors in the original paper Lay, V.; Effner, U.; Niederleithinger, E.; Arendt, J.; Hofmann, M.; Kudla, W. Ultrasonic Quality Assurance at Magnesia Shotcrete Sealing Structures. Sensors 2022, 22, 8717, https://doi.org/10.3390/s22228717. PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-584969 DO - https://doi.org/10.3390/s23187966 SN - 1424-8220 VL - 23 IS - 18 SP - 1 EP - 3 PB - MDPI CY - Basel AN - OPUS4-58496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heuchel, M. A1 - Hölck, Ole A1 - Böhning, Martin A1 - Siegert, R. A1 - Hofmann, D. ED - Qi, Y. ED - H.E. Fang, ED - N. Reynolds, ED - Liu, Z.-K. T1 - Knowledge-based approach to gas sorption in glassy polymers by combining experimental and molecular simulation techniques N2 - We present a method which allows to calculate gas sorption in complex polymers where, as slow processes, gas induced plasticization and volume dilation are important factors. Since the relaxational swelling of the polymer matrix that is observed at elevated gas concentrations takes hours or days, the swelling process is orders of magnitudes too slow to simulate the respective molecular dynamics in reasonable time and effort. To address this apparent incompatibility of experiment and simulation, we use single representative reference states from experiment and construct atomistic packing models according to these specifications. Gas sorption of CO2 and CH4 was successfully calculated on polysulfone, a 6FDA-polyimide, and a polymer of intrinsic microporosity, PIM-1, at 308 K and pressures up to 50 bar. T2 - MRS Fall Meeting 2008 - Symposium W - Computational Materials Design via Multiscale Modeling CY - Boston, MA, USA DA - 2008-12-01 KW - Gas sorption KW - Molecular modelling KW - Simulation KW - Glassy polymers PY - 2009 DO - https://doi.org/10.1557/PROC-1130-W06-10 VL - 1130 SP - W06 EP - W10 AN - OPUS4-19106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böhning, Martin A1 - Hölck, Ole A1 - Heuchel, M. A1 - Hofmann, D. T1 - Characterization of gas sorption in glassy polymers combining experimental and molecular modeling techniques KW - Glassy Polymers KW - Gas Sorption KW - Molecular Modelling KW - Diffusion PY - 2008 SN - 0743-0515 VL - 98 SP - 875 EP - 876 PB - Division of Polymeric Materials Science and Engineering, American Chemical Society CY - Washington, DC AN - OPUS4-17485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Nitschke-Pagel, T. A1 - Hofmann, M. T1 - In situ study of structural integrity of low transformation temperature (LTT)-welds N2 - We discuss the stability of weld residual strain under static and quasi cyclic transverse tensile loading in the elastic and elastic–plastic region. The test welds were joined with low transformation temperature weld filler materials with 10 wt% Cr and varying Ni-content from 8 to 12 wt%. Using neutron diffraction the residual lattice strain in the martensitic α'- and austenitic γ-phase in the fusion zone as well as the ferritic α-phase in the heat affected zone and base metal as induced by welding, superimposed by stepwise tensile loading and after unloading was measured. The amount of retained austenite in the fusion zone increases with increasing Ni-content, but it decreases with increasing load level due to stress induced martensite formation. In the as-welded condition the transverse macroscopic residual lattice strain was found to be in low compression in the fusion zone in each weld, while the heat affected zone was in tension. Local plastic deformation of the γ-phase as a result of yielding during tensile loading in combination with the change in phase fraction resulted in increased macroscopic compression in the fusion zone. The reduced yield strength in the heat affected zone resulted in plastic deformation and a considerable shift into compression. Comparison with the cross weld distribution of the hardness and FWHM of the neutron diffraction interference lines supported the assumption of plastic deformation of the γ- and α-phase in the fusion and heat affected zone, respectively, while the α'-phase in the fusion zone was stressed within the elastic regime only. Microstructural observations as well as measurement of the local γ-phase fraction by means of laboratory X-ray diffraction in the fusion zone strengthen these observations. KW - Low transformation temperature KW - Residual stress KW - Neutron diffraction PY - 2011 DO - https://doi.org/10.1016/j.msea.2011.03.091 SN - 0921-5093 SN - 1873-4936 VL - 528 IS - 16-17 SP - 5566 EP - 5575 PB - Elsevier CY - Amsterdam AN - OPUS4-24359 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gruskovà, J. A1 - Martin, G. A1 - Kresten, O. A1 - Mitthoff, F. A1 - Kaska, K. A1 - Hofmann, C. A1 - Kreuzer, W. A1 - Phelps, M. A1 - Boydston, K. A1 - Easton Jr., R. L. A1 - Knox, K. T. A1 - Kelbe, D. A1 - Kasotakis, D. A1 - Christens-Barry, W. A. A1 - Stewart, D. A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Glaser, L. A1 - Garrevoet, J. A1 - Shevchuk, I. A1 - Klumpp, S. A1 - Deckers, D. A1 - Buck, J. ED - Cronier, M. ED - Mondrain, B. T1 - Insights-into-the-Digital-Recovery-of-the-Scythica-Vindobonesia N2 - The Scythica Vindobonensia, the new fragments on Gothic incursions into Roman provinces in the Balkans in the middle of the third century AD that were revealed some years ago in a Greek palimpsest at the Austrian National Library in Vienna (ÖNB), are commonly considered as one of the most important additions of the last decades to the corpus of texts from classical Antiquity. Tere is a high degree of confdence among scholars in supposing that the fragments come from the lost work Scythica written in Greek by the third-century historian P. Herennius Dexippus (Δέξιππος) of Athens. The new fragments have hence also been called Dexippus Vindobonensis. In his Scythica, Dexippus recorded wars of the Romans with the Goths (and other tribes) whom he called Scythians. The work had been hitherto known only from excerpts and quotes by later authors. Eight pages of a Byzantine manuscript copy of the ancient text have survived hidden underneath the visible surface of the last four parchment folios of the Vienna manuscript Historicus graecus 73, f. 192r -195v4. The copy is written in a Greek calligraphic minuscule which has been estimated by palaeographers to be of the middle or the second half of the eleventh century. In the thirteenth century, the text (on each of the eight pages arranged in one column, with 30 lines per page) was washed of the parchment and the valuable material made from animal skin was re-used for Christian texts. The new writing largely covered the faded remnants of the original text. It thus became hidden from the human eye for more than seven hundred years. Its discovery by Jana Grusková, a classical philologist specialized in the transmission of Greek texts, resulted from a systematic review of all Greek palimpsests kept at the Austrian National Library in Vienna at the beginning of the twenty-first century and a detailed examination of the four folios in 2007-20097. KW - Scythica Vindobonensia, KW - Gothic incursions KW - A Greek palimpsest KW - Antiquity KW - Byzantine manuscript KW - Vienna manuscript PY - 2020 SN - 978-2-916716-81-7 SN - 0577-1471 VL - 2020 IS - 24/1 SP - 945 EP - 967 PB - Association des Amis du Centre d’Histoire et Civilisation de Byzance CY - Paris ET - 1 AN - OPUS4-53843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Schumann, J. A1 - Boltes, M. A1 - Holl, S. A1 - Hofmann-Böllinghaus, Anja T1 - The influence of physical and mental constraints to a stream of people through a bottleneck N2 - Understanding movement in heterogeneous groups is important for a meaningful evaluation of evacuation prediction and for a proper design of buildings. The understanding of interactions and influencing factors in heterogeneous groups on key performance figures is fundamental for a safe design. This contribution presents results of experimental studies on movement of a crowd through a bottleneck involving participants with and without disabilities. High precise trajectories of the attendees extracted from video recordings were used to calculate density and velocity of the participants. Besides the well-established fundamental diagram new insights into the individual relation between density and velocity are discussed. A complex structure and considerate behaviour in movement implicates a strong influence of the heterogeneity on key performance values of safe movement. T2 - 9th international conference on Pedestrian and Evacuation Dynamics (PED2018) CY - Lund, Sweden DA - 21.08.2018 KW - Human behaviour KW - Egress KW - Evacuation KW - Pedestrians with disabilities KW - Engineering data PY - 2018 SP - 57-1 EP - 57-6 CY - Lund, Sweden AN - OPUS4-46266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Rost, M. A1 - Krause, U. A1 - Hofmann-Böllinghaus, Anja T1 - Vergleichende Untersuchung zur Personensicherheit am Beispiel eines Seminarraumes N2 - Um den Anforderungen der Bauordnung an den Brandschutz für Gebäude gerecht zu werden, sind bauliche Anlagen so zu errichten und zu betreiben, dass der Entstehung eines Brandes und der Ausbreitung von Feuer und Rauch vorgebeugt, die Rettung von Menschen und Tieren sowie wirksame Löscharbeiten ermöglicht werden. Hierbei besteht, einer steigenden Komplexität sowie einem differenzierten Nutzungskonzept öffentlicher Gebäude geschuldet, häufig die Notwendigkeit von normativen Vorgaben abzuweichen und dennoch ein gleichwertiges Sicherheitsniveau nachzuweisen. Es werden Personensimulationsmodelle eingesetzt, die einerseits das Vorhandensein eines Schutzzielniveaus durch die Abbildungen von Personenbewegungen nachweisen können und andererseits durch Parametervariation eine szenarienabhängige Betrachtung ermöglichen. Der vorliegende Beitrag vergleicht die Ergebnisse einer kleinskaligen Evakuierungsübung mit drei mikroskopischen Personensimulationsmodellen und geht der Frage nach der Aussagekraft dieser Bewertungsmethode nach. Es zeigt sich, dass die alleinige Betrachtung absoluter Entleerungszeiten keine zuverlässige Beurteilungsgrundlage für das komplexe Schutzziel Personensicherheit darstellt. T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung CY - Magdeburg, Germany DA - 26.03.2015 KW - Evakuierung KW - Routenwahl KW - Fußgänger KW - Sicherheit KW - Simulation PY - 2015 SN - 978-3-00-048960-0 SP - 1 EP - 13 AN - OPUS4-33123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Polzin, R. M. A1 - Schumann, J. A1 - Holl, S. A1 - Hofmann-Böllinghaus, Anja T1 - Small-scale studies on evacuation characteristics of pedestrians with physical, mental or age-related disabilities N2 - Evaluation of evacuation process is common separated by two phases: pre-movement and movement-phase. Individual capabilities of pedestrians have an impact on both and therefore on the time required for safe escape. In view of evaluating the evacuation process, characteristics of realistic movements of pedestrians involved are needed, but so far such data are mainly available for individuals with unrestricted evacuation capabilities only. Due to the lack of available data, parameter studies in an assisted living for people with disabilities were performed to explore the movement during evacuation. Preparation times for assistance (n=10), unimpeded walking speeds (n=34) depending on the assistance devices in the plane as well as walking speeds on stairs (n=11) were focussed. Time to prepare an assistance device for utilisation depends significantly on the kind of device type. Further on, practical experience in handling the devices for assistance has an impact on the preparation time. In contrast to the results of the preparation times, any relation on assistance devices were investigated for the unimpeded walking speed in the plane. A remarkable decrease of walking speed on stairs was observed which is independent from the utilised assistance device. The presented data improve and extend the insufficient engineering data base and raised up questions regarding the complexity of considering pedestrians movement with impairments in evacuation planning. T2 - 3rd European Symposium on Fire Safety Science CY - Nancy, France DA - 12.09.2018 KW - Evacuation KW - Human behaviour KW - Egress KW - Pedestrians with disabilities KW - Engineering data KW - Unimpeded walking speed KW - Pre-movement KW - Movement PY - 2018 SP - 214966-1 EP - 214966-6 AN - OPUS4-46268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Evsevleev, Sergei A1 - Sevostianov, I. A1 - Mishurova, Tatiana A1 - Hofmann, M. A1 - Garcés, G. A1 - Bruno, Giovanni T1 - Explaining Deviatoric Residual Stresses in Aluminum Matrix Composites with Complex Microstructure N2 - The residual stresses in multiphase metal Matrix composites with both random planar-oriented short fibers and particles were studied by neutron diffraction and by a model based on the reformulation of classic Maxwell’s homogenization method. Contrary to common understanding and state-of-the-art models, we experimentally observed that randomly oriented phases possess non-hydrostatic residual stress. The recently developed modeling Approach allows calculating the residual stress in all phases of the composites. It rationalizes the presence of deviatoric stresses Accounting for the interaction of random oriented phases with fibers having preferential orientation. KW - Metal matrix composite KW - Residual stress KW - Deviatoric KW - Micromechanics PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-506472 DO - https://doi.org/10.1007/s11661-020-05697-1 VL - 51 IS - 6 SP - 3104 EP - 3113 PB - Springer AN - OPUS4-50647 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann, Michael A1 - Moufid, M. A1 - El Bari, N. A1 - Tiebe, Carlo A1 - Bouchikhi, B. T1 - Testing of a developed multigas sensor system for outdoor odour nuisance monitoring N2 - This work presents the testing of a developed elec¬tronic nose for outdoor odour nuisance monitoring. The sensor system consists of a sampling system, a measuring cell equipped with commercially available low-cost gas sensor elements and a data acquisition system. The sensor testing showed that the developed prototype is able to distinguish, identify and partially quantify individual odorous substances like ethanol, ammonia and hydrogen sulphide. Ethanol and ammonia could even be detected below or near their odour threshold. T2 - ALLSENSORS 2019, The Fourth International Conference on Advances in Sensors, Actuators, Metering and Sensing CY - Athens, Greece DA - 24.02.2019 KW - Electronic nose KW - Outdoor odour KW - Machined olfaction KW - Sensor testing PY - 2019 UR - https://www.thinkmind.org/index.php?view=article&articleid=allsensors_2019_2_40_70065 SN - 978-1-61208-691-0 SN - 2519-836X SP - 27 EP - 28 PB - The ThinkMind Digital Library AN - OPUS4-47505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Schumann, J. A1 - Boltes, M. A1 - Holl, S. A1 - Hofmann-Böllinghaus, Anja T1 - The influence of individual impairments on crowd dynamics N2 - Emergency exits as bottlenecks in escape routes are important for designing traffic facilities. Especially the fundamental diagram is a crucial performance criterion for assessment of pedestrians' safety in facilities and an important basis for calculation methods. For this reason, several studies were performed during the last decades which focus on the quantification of movement through bottlenecks. These studies were usually conducted with populations of homogeneous characteristics to reduce influencing variables and for reasons of practicability. Studies which consider heterogeneous characteristics in performance parameters are rarely available. In response and to reduce this lack of data a series of well-controlled large-scale movement studies considering pedestrians with different disabilities was carried out. T2 - Interflam 2019 CY - London, UK DA - 01.07.2019 KW - Evacuation PY - 2019 VL - 2019 SP - 775 EP - 791 PB - Interscience CY - London, UK AN - OPUS4-48647 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fritsch, Tobias A1 - Sprengel, Maximilian A1 - Evans, Alexander A1 - Farahbod-Sternahl, L. A1 - Saliwan Neumann, Romeo A1 - Hofmann, M. A1 - Bruno, Giovanni T1 - On the determination of residual stresses in additively manufactured lattice structures N2 - The determination of residual stresses becomes more complicated with increasing complexity of the structures investigated. Additive manufacturing techniques generally allow the production of ‘lattice structures’ without any additional manufacturing step. These lattice structures consist of thin struts and are thus susceptible to internal stress-induced distortion and even cracks. In most cases, internal stresses remain locked in the structures as residual stress. The determination of the residual stress in lattice structures through nondestructive neutron diffraction is described in this work. It is shown how two difficulties can be overcome: (a) the correct alignment of the lattice structures within the neutron beam and (b) the correct determination of the residual stress field in a representative part of the structure. The magnitude and the direction of residual stress are discussed. The residual stress in the strut was found to be uniaxial and to follow the orientation of the strut, while the residual stress in the knots was more hydrostatic. Additionally, it is shown that strain measurements in at least seven independent directions are necessary for the estimation of the principal stress directions. The measurement directions should be chosen according to the sample geometry and an informed choice on the possible strain field. If the most prominent direction is not measured, the error in the calculated stress magnitude increases considerably. KW - Additive manufacturing KW - Laser powder bed fusion KW - Residual stress KW - Principal stress components KW - Neutron diffraction KW - Lattice structures PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-520663 DO - https://doi.org/10.1107/S1600576720015344 SN - 1600-5767 VL - 54 SP - 228 EP - 236 AN - OPUS4-52066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Serrano-Munoz, Itziar A1 - Ulbricht, Alexander A1 - Fritsch, Tobias A1 - Mishurova, Tatiana A1 - Kromm, Arne A1 - Hofmann, M. A1 - Wimpory, R. C. A1 - Evans, Alexander A1 - Bruno, Giovanni T1 - Scanning Manufacturing Parameters Determining the Residual Stress State in LPBF IN718 Small Parts N2 - The influence of scan strategy on the residual stress (RS) state of an as-built IN718 alloy produced by means of laser powder bed fusion (LPBF) is investigated. Two scan vector rotations (90°-alternation and 67°-rotation), each produced following two different scan vector lengths (long and short), are used to manufacture four rectangular prisms. Neutron diffraction (ND) and laboratory X-ray diffraction (XRD) techniques are used to map the bulk and surface RS state, respectively. The distortion induced upon removal from the baseplate is measured via profilometry. XRD measurements show that the two long scan vector strategies lead to higher RS when compared with the equivalent short scan vector strategies. Also, the 67°-rotation strategies generate lower RS than their 90°-alternation counterparts. Due to the lack of reliable stress-free d0 references, the ND results are analyzed using von Mises stress. In general, ND results show significant RS spatial non-uniformity. A comparison between ND and distortion results indicates that the RS component parallel to the building direction (Z-axis) has a predominant role in the Z-displacement. The use of a stress balance scheme allows to discuss the d0 variability along the length of the specimens, as well as examine the absolute RS state. KW - As-built LPBF IN718 alloy KW - Scan strategy influence KW - Neutron diffraction KW - Residual stress state KW - Stress balance condition KW - Distortion PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526360 DO - https://doi.org/10.1002/adem.202100158 VL - 23 IS - 7 SP - 158 PB - Wiley AN - OPUS4-52636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ulbricht, Alexander A1 - Altenburg, Simon A1 - Sprengel, Maximilian A1 - Sommer, Konstantin A1 - Mohr, Gunther A1 - Fritsch, Tobias A1 - Mishurova, Tatiana A1 - Serrano-Munoz, Itziar A1 - Evans, Alexander A1 - Hofmann, M. A1 - Bruno, Giovanni T1 - Separation of the Formation Mechanisms of Residual Stresses in LPBF 316L N2 - Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured parts and important factors for the residual stress formation. This study examined the influence of heat accumulation on the distribution of residual stress in two prisms produced by Laser Powder Bed Fusion (LPBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two different border fill scan strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. The goal was to reveal the effect of different heat inputs on samples featuring the same solidification shrinkage. Residual stress was characterised in one plane perpendicular to the building direction at the mid height using Neutron and Lab X-ray diffraction. Thermography data obtained during the build process were analysed in order to correlate the cooling rates and apparent surface temperatures with the residual stress results. Optical microscopy and micro computed tomography were used to correlate defect populations with the residual stress distribution. The two scanning strategies led to residual stress distributions that were typical for additively manufactured components: compressive stresses in the bulk and tensile stresses at the surface. However, due to the different heat accumulation, the maximum residual stress levels differed. We concluded that solidification shrinkage plays a major role in determining the shape of the residual stress distribution, while the temperature gradient mechanism appears to determine the magnitude of peak residual stresses. KW - Additive Manufacturing KW - Laser Powder Bed Fusion KW - LPBF KW - AISI 316L KW - Online Process Monitoring KW - Thermography KW - Residual Stress KW - Neutron Diffraction KW - X-ray Diffraction KW - Computed Tomography PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-512903 DO - https://doi.org/10.3390/met10091234 VL - 10 IS - 9 PB - MDPI CY - Basel AN - OPUS4-51290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, Jakob A1 - Heldmann, A. A1 - Hofmann, M. A1 - Evans, Alexander A1 - Petry, W. A1 - Bruno, Giovanni T1 - Determination of diffraction and single-crystal elastic constants of laser powder bed fused Inconel 718 N2 - High energy X-ray synchrotron diffraction is used to investigate the elastic anisotropy of the nickel-based superalloy IN718 produced by laser powder bed fusion (PBF-LB). This material is characterized by a columnar grain morphology with some crystallographic texture. The material is subjected to elastic loading to determine the diffraction elastic constants (DECs). Furthermore, the single-crystal elastic constants (SCEC) are refined from these experiments using different micromechanical models. The results show that each micromechanical model predicts a specific set of SCEC that well describes the elastic anisotropy of PBF-LB/IN718. KW - Mechanical Engineering KW - Mechanics of Materials KW - Condensed Matter Physics KW - General Materials Science PY - 2023 DO - https://doi.org/10.1016/j.matlet.2023.135305 SN - 0167-577X VL - 353 SP - 1 EP - 5 PB - Elsevier B.V. AN - OPUS4-58477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moufid, M. A1 - Hofmann, Michael A1 - El Bari, N. A1 - Tiebe, Carlo A1 - Bartholmai, Matthias A1 - Bouchikhi, B. T1 - Wastewater monitoring by means of e-nose, VE-tongue, TD-GC-MS, and SPME-GC-MS N2 - The presence of wastewater and air pollution has become an important risk factor for citizens, not only in terms of problems related to health risks, but also because of its negative impact on the country's image. For this reason, malodorous emission monitoring and control techniques are in high demand in urban areas and industries. The aim of this work is first to build an electronic nose (e-nose) and a Voltammetric Electronic tongue (VE-tongue) in order to study their ability to discriminate between polluted and clean environmental samples. Secondly, Thermal Desorption-Gas Chromatography-Mass Spectrometry (TD-GC-MS), and Solid Phase Micro Extraction-Gas Chromatography–Mass Spectrometry (SPME-GC-MS) are utilized to explain this discrimination by identifying specific compounds from these samples. Indeed, the e-nose, consisted of metal oxide semiconductor gas sensors, is used for the assessment of the studied odorous air and headspace samples from water and wastewater sites. Moreover, the VE-tongue, based on metal electrodes, is utilized to determine the patterns of the sensor array responses, which serve as fingerprints profiles of the analyzed liquid samples. Chemometric tools, such as Principal Component Analysis (PCA), Hierarchical Cluster Analysis (HCA), and Support Vector Machines (SVMs) are operated for the processing of data from the e-nose and the VE-tongue. By using the both systems, the analyses of headspace and liquid samples from the seven sites allow better discrimination. To explain the cause of the obtained discrimination, TD-GC-MS and SPME-GC-MS analyses are well performed to identify compounds related sites. According to these outcomes, the proposed e-nose and VE-tongue are proved to be rapid and valuable tools for analysis of environmental polluted matrices. KW - Wastewater KW - Electronic nose KW - Voltammetric electronic tongue KW - Thermal desorption-gas chromatography-mass spectrometry KW - Solid phase micro extraction-gas chromatography–mass spectrometry PY - 2021 DO - https://doi.org/10.1016/j.talanta.2020.121450 VL - 221 SP - 121450 PB - Elsevier B.V. AN - OPUS4-51099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kempel, Florian A1 - Schartel, Bernhard A1 - Marti, J.M. A1 - Butler, K.M. A1 - Rossi, R. A1 - Idelsohn, S.R. A1 - Onate, E. A1 - Hofmann-Böllinghaus, Anja T1 - Modelling the vertical UL 94 test: competition and collaboration between melt dripping, gasification and combustion N2 - An experimental and numerical investigation of the effect of bisphenol A bis(diphenyl phosphate) (BDP) and polytetrafluoroethylene (PTFE) on the fire behaviour of bisphenol A polycarbonate/acrylonitrile butadiene styrene (PC/ABS) in the vertical UL 94 scenario is presented. Four PC/ABS blends were discussed, which satisfy different UL 94 classifications due to the competing effects of gasification, charring, flame inhibition and melt flow/dripping. For numerical investigation, the particle finite element method (PFEM) is used. Its capability to model the complex fire behaviour of polymers in the UL 94 is analysed. The materials' properties are characterised, in particular the additives impact on the dripping behaviour during thermal exposure. BDP is an efficient plasticiser; adding PTFE prevents dripping by causing a flow limit. PFEM simulations reproduce the dripping and burning behaviour, in particular the competition between gasification and dripping. The thermal impact of both the burner and the flame is approximated taking into account flame inhibition, charring and effective heat of combustion. PFEM is a promising numerical tool for the investigation of the fire behaviour of polymers, particularly when large deformations are involved. Not only the principal phenomena but also the different UL 94 classifications and the extinction times are well predicted. KW - Melt dripping KW - UL 94 KW - Particle finite element method (PFEM) KW - Simulation KW - Bisphenol A polycarbonate/acrylonitrile butadiene styrene (PC/ABS) KW - Polytetrafluoroethylene (PTFE) KW - Bisphenol A bis(diphenyl phosphate) (BDP) PY - 2015 DO - https://doi.org/10.1002/fam.2257 SN - 0308-0501 SN - 1099-1018 VL - 39 IS - 6 SP - 570 EP - 584 PB - Heyden CY - London AN - OPUS4-34285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kempel, Florian A1 - Schartel, Bernhard A1 - Hofmann-Böllinghaus, Anja A1 - Butler, K.M. A1 - Onate, E. A1 - Idelsohn, S.R. A1 - Rossi, R. A1 - Marti, J.M. T1 - Numerical simulation of polymeric materials in UL 94 test: Competition between gasification and melt flow/dripping T2 - Interflam 2010 - 12th International conference CY - Nottingham, UK DA - 2010-07-05 KW - Particle finite element method (PFEM) KW - UL 94 KW - Fire retardancy KW - PC/ABS KW - Melt flow KW - Dripping PY - 2010 SN - 978-0-9541216-5-5 N1 - Geburtsname von Hofmann-Böllinghaus, Anja: Hofmann, A. - Birth name of Hofmann-Böllinghaus, Anja: Hofmann, A. VL - 1 SP - 721 EP - 730 PB - Interscience Communications CY - London, UK AN - OPUS4-21670 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jentsch, H. A1 - Schwartz, A. A1 - Basedau, Frank A1 - Bazrafshan, K. A1 - Döring, H. A1 - Großwig, S. A1 - Hofmann, Detlef A1 - Kowalle, G. A1 - Kusche, Nadine A1 - Lorenz, R. A1 - Pfeiffer, T. A1 - Sadaghiani, M.R.S. A1 - Scholz, E. A1 - Senze, A. A1 - Tkachenko, Viktoriya A1 - Witt, K. J. ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Detection of slipping soil areas with embedded tiny vertical sensing rods N2 - Critical soil zones where large areas along a shear joint might begin to slip should be recognized. In order to avoid damage, monitoring of such unstable zones is necessary. First, soil movements must be detected as early as possible, second, the amount of deformation should be estimated. Because geodetical methods do not provide information about deformation in the underground in different depths, the only way to come to information from possible shear zones is the installation of deformation measurement systems. A special installation method was developed to bring a long-gauge length measurement system into a borehole and transfer data of soil deformations into an installed sensing rod. The mostly vertically installed sensing rod has an outer diameter of 3 mm to 6 mm and contains several optical fibres. One fibre provides integral strain information along the whole length of the rod. To get this information, the phase difference between the fibre input and output is measured and the change of the total length of the fibre can be derived. This easy and cheap online sensing system delivers an early warning of soil deformations respectively possible slip as well as landslides. In case of warning, the second sensing system based on Fibre Bragg Grating sensors located close to the expected shear zone purposefully. It records resulting deformations in detail. In this study, three main objectives were achieved: a) development of tiny pultruded sensing rods with integrated optical sensor fibres, b) installation technology which enables the integration of the sensing rod during drilling and pile driving, and c) development of a stiff but elastic racking material to fix the rod in the soil and to transfer soil deformation into the stiffer sensing rod. These three aspects including the fibre optical measurement systems are described; results from Press Deformation Test (PDT) are presented. Test results of the fibre optical online system are compared and evaluated with the results of conventional inclinometer measurements as well as numerical modelling. An outlook for further possibilities of usage of this monitoring system is given. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Structural health monitoring KW - Soil stability monitoring KW - Optical fibre strain-sensor KW - Geotechnical soil stability KW - Soil deformation modelling PY - 2013 SN - 978-962-367-768-4 SP - 1 EP - 9 AN - OPUS4-29915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Polzin, R.M. A1 - Holl, S. A1 - Hofmann-Böllinghaus, Anja T1 - Berücksichtigung von Personen mit körperlichen, geistigen oder altersbedingten Beeinträchtigungen in der Evakuierungsforschung N2 - Studien zur Erforschung von Kenngrößen der Bewegung von Personen wurden in der Vergangenheit meistens mit jungen und fitten Menschen durchgeführt. In Folge des demographischen Wandels und der Anforderungen an barrierefreies Bauen stellt sich die Frage, ob die so ermittelten Kenngrößen der Bewegung auch auf heterogene Personengruppen übertragen werden können. Da bei der Berechnung von Räumungszeiten zunehmend Ingenieurmethoden eingesetzt werden, deren Ergebnisse ganz wesentlich von den zu Grunde gelegten Bewegungsparametern, wie z. B. der freien Gehgeschwindigkeit, abhängen, hat die Validität der Kenngrößen maßgeblichen Einfluss auf die sicherheitstechnische Evaluation von Gebäuden und Versammlungsstätten. In diesem Artikel wird anhand aktueller Forschungsergebnisse aus Bewegungsstudien, an denen Menschen mit und ohne Beeinträchtigungen teilgenommen haben, der Einfluss der Heterogenität auf Kenngrößen der Bewegung vorgestellt. Darüber hinaus werden die Besonderheiten des Studienablaufs und die Möglichkeiten und Grenzen der Untersuchungsmethode dargestellt. Die Untersuchungen bestätigen, dass die Berücksichtigung besonderer Personengruppen signifikanten Einfluss auf die Kenngrößen der Bewegung hat und daher die Ergebnisse der Ingenieurmethoden beeinflusst und zukünftig bei heterogenen Personengruppen beachtet werden muss. T2 - 65. Jahresfachtagung der Vereinigung zur Förderung des Deutschen Brandschutzes e.V. CY - Duisburg, Germany DA - 28.05.2018 KW - Evakuierung KW - Egress KW - Heterogenität KW - ASET KW - RSET PY - 2018 SN - 978-3-936050-28-8 SP - 189 EP - 204 PB - VdS Schadensverhütung GmbH Verlag CY - Köln AN - OPUS4-45082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -