TY - GEN A1 - Müller, R. A1 - Brechbühl, Y. A1 - Lutzenberger, S. A1 - Said, Samir A1 - Auersch, Lutz A1 - Guigou-Carter, C. A1 - Villot, M. A1 - Müller, R. ED - Degrande, G. ED - al., et T1 - Vibration Excitation at Turnouts, Mechanism, Measurements and Mitigation Measures N2 - There is a strong need for cost-effective mitigation measures for turnouts. SBB has initiated a series of examinations using different methodologies to gain a deeper understanding of the excitation mechanisms at low frequencies, in addition to that obtained in the RIVAS project. To date it is not yet clear what constitutes a complete measurement data set that would enable understanding most of the vibration excitation mechanisms in turnouts. Increasing vibration at turnouts in comparison to normal track is observed for all measured frequencies. The different methodologies are presented in the paper. Under-sleeper pads (USP) are a cost-effective method to reduce vibration at frequencies above 63 Hz (1/3 octave), but there is probably no improvement for frequencies below 63 Hz. A first test of new frog geometry did not show relevant improvements in Vibration emission in comparison to a reference frog geometry. Axle box acceleration measurements are an interesting method to identify defects in a turnout. A specialized measurement system of rail roughness could identify certain geometry Problem areas for some frogs. Noise increases also are observed at turnouts for frequencies ranging between 80 to 1000 Hz. The use of railway source models to calculate contact forces for ballasted track and turnouts seems promising, in particular for understanding the influence of ground. KW - Turnout KW - Switch KW - Vibration excitation KW - Vibration measurements PY - 2021 SN - 978-3-030-70288-5 DO - https://doi.org/10.1007/978-3-030-70289-2_42 SN - 1612-2909 VL - 150 SP - 403 EP - 410 PB - Springer Nature Switzerland AG CY - Cham AN - OPUS4-52612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ahrendt, H. A1 - Gesatzke, Roger A1 - Hahn, G. A1 - Herrmann, P. A1 - Julien, H. A1 - Karger, R. A1 - Kaufmann, M. A1 - Krebs, H.-J. A1 - Lucht, J. A1 - Müller, A. A1 - Müller, R. A1 - Vetter, B. T1 - Überdruckmessgeräte nach DIN EN 837 - Auswahl und Anwendung KW - Druckmessgerät KW - Sicherheit PY - 2007 SN - 978-3-410-16626-9 IS - 1. Auflage SP - 1 EP - 89 PB - Beuth CY - Berlin AN - OPUS4-15994 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ewers, Benjamin A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Müller, Bernd R. A1 - Hoehl, a. A1 - Müller, R. A1 - Ulm, G. T1 - Terahertz spectral computed tomography N2 - The novel technique of spectral THz computed tomography is demonstrated at an example of a small plastic figure. The data are reconstructed by conventional filtered back-projection. The reconstruction are discussed. T2 - IRMMW-THz 2009 - 34th International conference on infrared, millimeter, and terahertz waves CY - Busan, Korea DA - 2009-09-21 KW - THz KW - Computed tomography PY - 2009 SN - 978-1-4244-2120-6 SP - 1 EP - 2(?) AN - OPUS4-20546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Wolfgang A1 - Torge, Manfred A1 - Adam, Karin A1 - Römich, H. A1 - Weissmann, R. A1 - Drewello, R. ED - Wolff, A. T1 - Naturwissenschaft im Dienst der Restaurierung KW - Kulturguterhaltung KW - Glaszusammensetzung KW - Mikroorganismen PY - 2000 SN - 3-8053-2648-3 SP - 65 EP - 99 PB - von Zabern CY - Mainz AN - OPUS4-3236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krause, Martin A1 - Bärmann, R. A1 - Frielinghaus, R. A1 - Kreschmar, F. A1 - Krogge, O. A1 - Langenberg, K. A1 - Maierhofer, Christiane A1 - Müller, W. A1 - Neisecke, J. A1 - Schickert, M. A1 - Schmitz, V. A1 - Wiggenhauser, Herbert A1 - Wollbold, F. ED - Schickert, G. T1 - Comparison of pulse-echo-methods for testing concrete T2 - International Symposium Non-Destructive Testing in Civil Engineering (NDT-CE) CY - Berlin, Germany DA - 1995-09-26 KW - Beton KW - Radar KW - Aufprallecho KW - Ultraschall KW - Prüfung PY - 1995 SN - 3-931381-02-1 N1 - Serientitel: BB / DGZfP – Series title: BB / DGZfP SP - 281 EP - 295 PB - DGZfP, Dt. Ges. für Zerstörungsfreie Prüfung e.V. CY - Berlin AN - OPUS4-593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Takahashi, Kazunori A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Brekow, Gerhard A1 - Böhm, R. A1 - Ronneteg, U. A1 - Pitkänen, J. T1 - POD Evaluation of NDE Techniques for Canister-Components for Risk Assessment of Nuclear Waste Encapsulation T2 - 6th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurised Components CY - Budapest, Hungary DA - 2007-10-08 KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - POD PY - 2008 SN - 978-92-79-08897-1 DO - https://doi.org/10.2790/1274 SN - 1018-5593 SP - 168 EP - 179 AN - OPUS4-18589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Berger, Georg A1 - Mensing, M. A1 - Sittinger, M. A1 - Gross, U. A1 - Rahmanzadeh, R. A1 - Müller-Mai, C. ED - Haas, N. P. T1 - Autologe Chondrozyten Transplantation durch Tissue Engineering auf resorbierbaren bioaktiven Biomaterialträgern T2 - 64. Jahrestagung der Deutschen Gesellschaft für Unfallchirurgie CY - Hannover, Deutschland DA - 2000-09-10 PY - 2000 SN - 3-540-67734-8 SN - 0945-1382 N1 - Serientitel: Hefte zur Zeitschrift "Der Unfallchirurg" – Series title: Hefte zur Zeitschrift "Der Unfallchirurg" IS - 282 SP - 1(?) PB - Springer CY - Berlin AN - OPUS4-948 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bürgisser, Philip A1 - Müller, Urs A1 - Meng, Birgit A1 - Abart, R. ED - Leon Black, ED - Phil Purnell, T1 - Influence of natural pozzolans of mechansims of the alkali silica reaction (ASR) in concrete T2 - 29th Cement and concrete science conference CY - Leeds, UK DA - 2009-09-07 KW - AKR KW - Natürliche puzzolanische Zusatzstoffe KW - C-S-H Phasen PY - 2009 SN - 978-0-85316-281-0 SP - 143 EP - 146 AN - OPUS4-20249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bürgisser, Philip A1 - Müller, Urs A1 - Meng, Birgit A1 - Abart, R. ED - Stark, J. T1 - Der Einfluss von natürlichen Puzzolanen vulkanischen Ursprungs auf die Alkali-Kieselsäurereaktion (AKR) im Beton T2 - 17. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2009-09-23 KW - AKR KW - Natürliche puzzolanische Zusatzstoffe KW - C-S-H Phasen PY - 2009 SN - 978-3-00-027265-3 VL - 2 SP - 2-0687 - 2-0692 CY - Weimar AN - OPUS4-20298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Harbich, Karl-Wolfram A1 - Lange, Axel A1 - Schors, Jörg A1 - Müller, Bernd R. T1 - Röntgen-Topographie mit Klein- und Weitwinkel-Streuung N2 - Röntgen-Topographische Verfahren sind dadurch gekennzeichnet, daß die Streueigenschaften eines Probekörpers ortskorreliert erfaßt werden. Somit vereinigen sie die Vorzüge der bildgebenden Eigenschaft der Radiographie mit der Strukturselektivität der Röntgenanalyse. Sowohl die Röntgen-Weitwinkel-Streuung als auch die Röntgen-Kleinwinkel-Streuung (-Beugung und -Refraktion) werden topographisch für die Materialcharakterisierung eingesetzt. Die Topographie-Verfahren und Untersuchungsbeispiele an nichtmetallischen Werkstoffen werden dargestellt. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 KW - Röntgen-Streuung KW - Materialcharakterisierung KW - Komposite KW - Keramik PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/v15/v15.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD PB - DGZfP CY - Berlin AN - OPUS4-2027 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Marco A1 - Hentschel, Manfred P. A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen A1 - Bamberg, J. A1 - Heutling, F. ED - Danny Van Hemelrijck, ED - Igor Solodov, ED - Anastasopoulos, Athanasios ED - Gerhard Busse, T1 - Synchrotron-Refraction-Computed-Tomography for NDT and characterisation of lightweight composite materials T2 - 4th International Conference of Emerging Technologies in Non-Destructive Testing (ETNDT 4) CY - Stuttgart, Germany DA - 2007-04-02 KW - Refraction KW - Computed Tomography KW - NDE KW - Ti-MMC PY - 2008 SN - 978-0-415-46476-5 SP - 217 EP - 221 PB - Taylor & Francis CY - London, UK AN - OPUS4-18680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen A1 - Bamberg, J. A1 - Heutling, F. T1 - Micro Crack Characterization of Metal Matrix Composites by 3D-Refraction-Computed-Tomography T2 - 16th World Conference on Nondestructive Testing CY - Montreal, Canada DA - 2004-08-30 KW - NDE KW - X-ray refraction KW - Composites KW - MMC PY - 2004 SP - 9 pages PB - International Committee for Non-Destructive Testing CY - Montreal AN - OPUS4-5486 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. T1 - Submikro-Computer-Tomographie an der BAMline T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2004 CY - Salzburg, Österreich DA - 2004-05-17 KW - Computer Tomographie KW - Vergrößerung mit asymmetrischen Kristallen PY - 2004 UR - http://www.ndt.net/article/dgzfp04/papers/v09/v09.htm SN - 3-931381-55-2 SP - 1(?) EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-5869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Goebbels, Jürgen A1 - Müller, Bernd R. A1 - Riesemeier, Heinrich A1 - Weidemann, Gerd ED - Mazal, P. T1 - Special Solutions for CT-Investigations with Synchrotron Radiation T2 - 2nd International Workshop of NDT Experts CY - Prague, Czech Republic DA - 2003-10-06 KW - Computed Tomography KW - Synchrotron radiation KW - X-ray refraction KW - Metal matrix composites KW - Porosity PY - 2003 SN - 80-2142475-3 SP - 91 EP - 97 PB - Univ. of Technology CY - Brno AN - OPUS4-2876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen T1 - First refraction enhanced 3D computed tomography T2 - International Symposium on Computed Tomography and Image Processing for Industrial Radiology CY - Berlin, Germany DA - 2003-06-23 PY - 2003 SN - 3-931381-48-X N1 - Serientitel: DGZfP-Proceedings BB – Series title: DGZfP-Proceedings BB IS - 84-CD PB - DGZfP CY - Berlin AN - OPUS4-2519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. A1 - Illerhaus, Bernhard A1 - Goebbels, Jürgen A1 - Bamberg, J. A1 - Heutling, F. T1 - 3D Refraction Computed Tomography Applied to Metal Matrix Composites N2 - For the first time Metal Matrix Composites (MMC) have been investigated by 3D Computed Tomography combined with enhanced interface contrast due to X-ray refraction. X-ray refraction is a relatively new approach for the characterization of advanced materials. The related techniques of Refraction Topography and Refraction Computed Tomography have been developed and applied at our laboratory during the last decade to meet the actual demand for improved nondestructive characterization of high performance composites, ceramics and other low density materials and components. X-ray refraction occurs, when X-rays crosses interfaces of spherical or cylindrical shape (e.g. pores or fibres) in the same way as visible light is refracted by lenses. These X-ray optical effects can be observed at small scattering angles of few minutes of arc as the refractive index n of X-rays is nearly unity (n = 1 – 10-6). Due to the short X-ray wavelength of about 0.1 nm the technique determines the amount of inner surfaces and interfaces of nanometer dimensions. The technique is expected to solve many problems in understanding the meaning of micro and sub micro structures in materials science. With the results of the CT investigation, some questions could be clarified for a better understanding of fatigue failure mechanisms under cyclic loading conditions. The specimens for the test programme have been provided by MTU Aero Engines. They consist of a titanium matrix (Ti6242) reinforced by SiC fibres (SCS6). The investigations have been performed at the materials research station of BAM (BAMline) at the Synchrotron Facility BESSY in Berlin, Germany. T2 - 35th International SAMPE technical conference CY - Dayton, OH, USA DA - 2003-09-28 KW - Non-Destructive Inspection (NDI) KW - Characterization KW - Titanium Metal Matrix Composites (Ti-MMC) KW - Ti6242 KW - SCS6 PY - 2003 SN - 0-938994-95-6 PB - SAMPE CY - Covina, Calif. AN - OPUS4-2780 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. ED - Paul Sellin, T1 - Refraction enhanced micro-CT for non-destructive materials characterization T2 - IEEE Nuclear Science Symposium CY - Dresden, Germany DA - 2008-10-19 KW - Synchrotron KW - Micro-CT KW - Refraction PY - 2008 SN - 978-1-4244-2715-4 SN - 1082-2654 SP - 541 EP - 546 AN - OPUS4-18662 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael A1 - Hentschel, Manfred P. T1 - Synchrotron Based Micro-CT and Refraction Enhanced Micro-CT of MMC T2 - International Symposium on NDT in Aerospace CY - Fürth, Germany DA - 2008-12-03 KW - X-ray Refraction KW - Synchrotron Radiation KW - Computed Tomography KW - Metal Matrix Composites KW - Lightweight Materials KW - Aerospace PY - 2008 SN - 978-3-940283-12-2 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - DGZfP-BB 114 (Poster 10) SP - 295 EP - 305 PB - DGZfP CY - Berlin AN - OPUS4-18607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Müller, Bernd R. ED - Czichos, Horst ED - Tetsuya Saito, ED - Leslie Smith, T1 - Computed tomography - Application to composites and microstructures KW - Microstructures KW - Computed tomography KW - X-ray refraction tomography KW - Composites PY - 2006 SN - 978-3-540-20785-6 SP - 870 EP - 875 PB - Springer CY - Berlin AN - OPUS4-14066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Hentschel, Manfred P. ED - Cohen, L. J. T1 - Non-Destructive Characterization of High Performance Composites by use of X-Ray Refraction Topography T2 - 48th International SAMPE symposium and exhibition CY - Long Beach, CA, USA DA - 2003-05-11 KW - Non-Destructive Inspection (NDI) KW - Characterization KW - Advanced Composite PY - 2003 SN - 0-938994-94-8 VL - 1 SP - 1203 EP - 1211 PB - SAMPE International Business Office CY - Covina, Calif. AN - OPUS4-2542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Ekenhorst, Derk A1 - Brzezinka, Klaus-Werner A1 - Hentschel, Manfred P. ED - Krenkel, W. T1 - Fiber Induced Failure of Carbon/Carbon Composites T2 - 4th International Conference on High Temperature Ceramic Matrix Composites ; 4th HT-CMC Conference CY - Munich, Germany DA - 2001-10-01 PY - 2001 SN - 3-527-30320-0 VL - 4 SP - 175 EP - 180 PB - Wiley-VCH CY - Weinheim AN - OPUS4-1289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Hentschel, Manfred P. ED - Green, R. E. ED - Djordjevic, B. B. ED - Hentschel, M. P. T1 - Synchrotron Radiation Refraction Topography PY - 2003 SN - 3-540-40154-7 SP - 167 EP - 176 PB - Springer CY - Berlin AN - OPUS4-2765 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Hentschel, Manfred P. A1 - Lange, Axel T1 - SYRTOPO - Materialcharakterisierung an der BAMline N2 - Einleitung Die Bundesanstalt für Materialforschung und -prüfung (BAM) hat im Synchrotronstrahlungslabor BESSY (im Wissenschafts- und Technologiezentrum Berlin-Adlershof) ein Röntgen-Strahlrohr (BAMline) sowie einen Messplatz für die zerstörungsfreie Materialcharakterisierung aufgebaut. Der Messplatz erlaubt die Untersuchung mit monochromatischer Röntgenstrahlung im Energiebereich von 5keV bis 60keV mit hohem Photonenfluß. Seit Anfang 2001 läuft der Probebetrieb zur Optimierung der Strahlungsquelle sowie des experimentellen Aufbaus. Die Besonderheiten der BAMline im Vergleich zu Laboröntgenquellen sind der hohe Photonenfluss bei freier Wahl der Photonenenergie sowie die Polarisationseigenschaften und die außerordentliche Parallelität der Strahlung bei großem Strahlungsquerschnitt. Dies ermöglicht Refraktionstopogramme für Metall-Matrix-Komposite (MMC) in relativ kurzer Zeit, mit einer lateralen Ortsauflösung von 10µm, zu messen. Das neuartige ZfP-Verfahren der Röntgen-Refraktions-Topograhy wurde an anderer Stelle ausführlich beschrieben [1,2]. Es nutzt die Messtechnik der traditionellen Kleinwinkelstreuung auf unkonventionelle Weise, und wurde in den letzten zehn Jahren in unserem Labor entwickelte und an die fortgeschrittenen Anforderungen für die zerstörungsfreie Charakterisierung von neuartigen Werkstoffen wie faserverstärkten Kompositen und Keramiken angepasst. Das Verfahren basiert auf dem Brechungseffekt von Röntgenstrahlen. Auf Grund der kurzen Wellenlänge der Röntgenstrahlen (l » 0.1nm) können innere Oberflächen sowie Grenzflächenkonzentrationen von Nanometer Große detektiert werden, so dass mit Hilfe dieser Technik sehr leicht Partikel, Risse und Porengrößen im Sub-Mikrometer-Bereich gemessen werden können, ohne dabei die Proben zu zerstören, wie es bei mikroskopischen Techniken notwendig ist. Anwendungsfelder dieser Untersuchungsmethode sind z.B. die Erkennung von Faser-Matrix-Enthaftung nach Schlageinwirkung sowie Rissbildung durch Alterung und Herstellung bei faserverstärkten Kompositen. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2002 CY - Weimar, Deutschland DA - 2002-05-06 PY - 2002 UR - http://www.ndt.net/article/dgzfp02/papers/v16/v16.htm SN - 3-931381-39-0 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 80-CD SP - 1(?) EP - 6(?) PB - DGZfP CY - Berlin AN - OPUS4-2793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Wald, Oliver T1 - Quantitative X-ray Determination of CFRP Micro Structures T2 - International Symposium on NDT in Aerospace CY - Fürth, Germany DA - 2008-12-03 KW - Neutronen-Radiographie KW - Neutronen-Tomographie KW - Tomographische Rekonstruktionsalgorithmen KW - Brennstoffzellen KW - In-Situ Radiologie PY - 2008 SN - 978-3-940283-12-2 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - DGZfP-BB 114 (X-Ray/Lecture 13) SP - 89 EP - 98 PB - DGZfP CY - Berlin AN - OPUS4-18606 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Lange, Axel A1 - Müller, Bernd R. A1 - Schors, Jörg A1 - Harbich, Karl-Wolfram T1 - Röntgen-Refraktions-Computer-Tomographie N2 - Für die Charakterisierung Neuer Werkstoffe, vornehmlich Nichtmetalle, hat sich das Verfahren der Röntgen-Refraktions-Topographie bewährt. Es handelt sich phänomenologisch um eine Technik der Röntgen-Kleinwinkel-Streuung mit Probekörper-Abtastung bei fest vorgewähltem Streuwinkel. Gegenüber der klassischen Beugungstheorie dominieren jedoch bei der Streuung an Strukturen oberhalb von 0.3 µm Größe röntgenoptische Brechungseffekte. Detektierbar sind damit innere Ober- und Grenzflächen, insbesondere Mikrorisse unterhalb der lichtmikroskopischen Erkennbarkeit. Da es sich hierbei um eine Durchstrahlungs-Technik handelt, überlagern jedoch die Strukturen zu einer Projektion, analog zu den radiographischen Verfahren. Um auch Informationen entlang der Durchstrahlungs-Richtung in der Tiefe des Probekörpers zu erhalten, wird unter kleinen Streuwinkeln die Computer-Tomographie durchgeführt, im ersten Ansatz mit nur zwei Meßkanälen, jeweils für die Messung der Absorptions- und der Refraktions-Intensität. Dazu werden nacheinander 360 Linear-Scans nach Drehung von jeweils 1° aufgenommen. Die Intensitätswerte werden nach den Regeln der fouriergefilterten Rückprojektion zu Computer-Tomogrammen verarbeitet. Die Ergebnisse visualisieren die Anordnung von Grenzflächen und innere Oberflächen, die sich für zahlreiche nichtmetallische Werkstoffe, vor alllem im Transportmittel-Leichtbau als relevante Mikrostrukturen für das Versagens-Verhalten und die Werkstoff-Optimierung eignen. Zum Vergleich entstehen aus den simultanen Absorptionsmessungen gleichzeitig die klassischen Computer-Tomogramme, die ausschließlich Dichteänderungen anzeigen. T2 - Jahrestagung Zerstörungsfreie Materialprüfung 1999 CY - Celle, Deutschland DA - 1999-05-10 KW - Röntgentomographie KW - Röntgen-Refraktions-Computer-Tomographie PY - 1999 UR - http://www.ndt.net/abstract/dgzfp99/data/40.htm SN - 3-931381-27-7 VL - 1 IS - 68 SP - 361 EP - 369 PB - DGZfP CY - Berlin AN - OPUS4-715 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Müller, Bernd R. A1 - Harwardt, Michael A1 - Lange, Axel T1 - Synchrotron-Refraktions-Computer Tomographie für die Materialforschung T2 - DGZfP Jahrestagung CY - Rostock, Deutschland DA - 2005-05-02 KW - Computer-Tomographie KW - Synchrotronstrahlung KW - Refraktionskontrast KW - Bragg-Vergrößerung PY - 2005 SN - 3-931381-64-1 N1 - Serientitel: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. – Series title: Berichtsband / Deutsche Gesellschaft für zerstörungsfreie Prüfung e. V. IS - 94-CD SP - 1(?) EP - 7(?) PB - DGZfP CY - Berlin AN - OPUS4-11698 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Bernd R. A1 - Trappe, Volker A1 - Goebbels, Jürgen A1 - Hickmann, Stefan A1 - Grasse, Fabian T1 - Non-destructive characterization of composites: from small scale to complex component testing - a challenge T2 - International Symposium on NDT in Aerospace CY - Hamburg, Germany DA - 2010-11-22 KW - Aircraft KW - Wind turbine blades KW - Automotive KW - X-ray refraction KW - Fibre orientation KW - WAXS technique KW - X-ray computed tomography PY - 2010 SN - 978-3-940283-28-3 IS - DGZfP-BB 124 (Tu.2.B.1) SP - 1 EP - 6 AN - OPUS4-22724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hentschel, Manfred P. A1 - Harbich, Karl-Wolfram A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Schors, Jörg A1 - Wald, Oliver ED - Gerhard Busse, ED - Danny Van Hemelrijck, ED - Igor Solodov, ED - Anastasopoulos, Athanasios T1 - NDE of micro structured materials by X-ray diffraction and refraction topography T2 - 4th International Conference of Emerging Technologies in Non-Destructive Testing (ETNDT 4) CY - Stuttgart, Germany DA - 2007-04-02 KW - Nondestructive testing KW - X-ray scattering KW - X-ray topography KW - Computed topography KW - Synchrotron refraction computed tomography KW - Structure property relations KW - Composite damaging KW - Ceramics KW - Foams PY - 2007 SN - 978-0-415-46476-5 SP - 15 EP - 22 PB - Taylor & Francis CY - London, UK AN - OPUS4-17561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Baer, D. R. A1 - Cant, D. J. H. A1 - Castner, D. G. A1 - Ceccone, G. A1 - Engelhard, M. H. A1 - Karakoti, A. S. A1 - Müller, Anja ED - Hodoroaba, Vasile-Dan ED - Unger, Wolfgang ED - Shard, A. G. T1 - Preparation of nanoparticles for surface analysis N2 - A variety of methods used to prepare nano-objects for surface analysis are described along with information about when they might be best applied. Intrinsic properties of NPs which complicate their characterization and need to be considered when planning for surface or other analyses of NPs are identified, including challenges associated with reproducible synthesis and functionalization of the particles as well as their dynamic nature. The relevant information about the sample preparation processes, along with analysis details and data that need to be added to the collection of material provenance information is identified. Examples of protocols that have been successfully used for preparation of nano-objects for surface analysis are included in an annex. KW - Sample preparation KW - Nanoparticles KW - Surface chemistry KW - XPS KW - Dynamic behavior KW - Nano-object KW - Surface analysis PY - 2020 SN - 978-0-12-814182-3 DO - https://doi.org/10.1016/B978-0-12-814182-3.00018-3 SP - 295 EP - 347 PB - Elsevier CY - Amsterdam AN - OPUS4-50186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stephan, Ina A1 - Askew, P. A1 - Gorbushina, Anna A1 - Grinda, Manfred A1 - Hertel, Horst A1 - Krumbein, W.E. A1 - Müller, R.-J. A1 - Pantke, Michael A1 - Plarre, Rüdiger A1 - Schmitt, G. A1 - Schwibbert, Karin ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Biogenic impact on materials N2 - Materials as constituents of products or components of technical systems rarely exist in isolation and many must cope with exposure in the natural world. This chapter describes methods that simulate how a material is influenced through contact with living systems such as microorganisms and arthropods. Both unwanted and desirable interactions are considered. This biogenic impact on materials is intimately associated with the environment to which the material is exposed (Materials-Environment Interaction, Chap. 15). Factors such as moisture, temperature and availability of food sources all have a significant influence on biological systems. Corrosion (Chap. 12) and wear (Chap. 13) can also be induced or enhanced in the presence of microorganisms. Section 14.1 introduces the categories between desired (biodegradation) and undesired (biodeterioration) biological effects on materials. It also introduces the role of biocides for the protection of materials. Section 14.2 describes the testing of wood as a building material especially against microorganisms and insects. Section 14.3 characterizes the test methodologies for two other groups of organic materials, namely polymers (Sect. 14.3.1) and paper and textiles (Sect. 14.3.2). Section 14.4 deals with the susceptibility of inorganic materials such as metals (Sect. 14.4.1), concrete (Sect. 14.4.2) and ceramics (Sect. 14.4.3) to biogenic impact. Section 14.5 treats the testing methodology concerned with the performance of coatings and coating materials. In many of these tests specific strains of organisms are employed. It is vital that these strains retain their ability to utilize/attack the substrate from which they were isolated, even when kept for many years in the laboratory. Section 14.6 therefore considers the importance of maintaining robust and representative test organisms that are as capable of utilizing a substrate as their counterparts in nature such that realistic predictions of performance can be made. KW - Materialschutz KW - Biologie KW - Organismus KW - Standard KW - Prüfung PY - 2011 SN - 978-3-642-16640-2 SP - 769 EP - 844 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -