TY - RPRT A1 - Weimann, Karin A1 - Matyschik, Jan A1 - Adam, Christian A1 - Schulz, T. A1 - Linß, E. A1 - Müller, A. T1 - Optimierung des Rückbaus/Abbruchs von Gebäuden zur Rückgewinnung und Aufbereitung von Baustoffen unter Schadstoffentfrachtung (insbes. Sulfat) des RCMaterials sowie ökobilanzieller Vergleich von Primär- und Sekundärrohstoffeinsatz inkl. Wiederverwertung T2 - UFOPLAN 3709 33 317 / Bauschutt - Schlussbericht (UBA-Texte, Heft 05/2013) N2 - Aufgrund der großen Massenströme ist das Recycling von Baurestmassen von besonderer Bedeutung für die Schonung von natürlichen Ressourcen. Eine wichtige Voraussetzung für ein hochwertiges Recycling, wie z.B. eine Wiederverwertung von aufbereitetem Bauschutt/Altbeton als rezyklierte Gesteinskörnung im Hochbau, ist die Einhaltung von Grenzwerten für Stör- und Schadstoffe. Dabei steht der Sulfatgehalt im Eluat von Bauschutt besonders im Fokus. In der vorliegenden Studie wird untersucht, wie durch die Optimierung von Abbrucharbeiten und Bauschuttaufbereitung hochwertige Gesteinskörnungen aus Altbeton gewonnen werden können. Anhand von Literatur- und Datenrecherchen werden zunächst Sulfatquellen in Gebäuden sowie verfügbare Abbruch- und Aufbereitungstechniken zusammengestellt. Am Beispiel von unterschiedlichen Gebäudetypen werden Szenarien für selektiven und nicht selektiven Abbruch (Schwerpunkt: Sulfatentfachtung) in Hinblick auf ihre Umweltwirkungen ökobilanziell bewertet. Ergänzt werden diese Bewertungen durch Untersuchungen an realen Bauschuttmaterialien und Abbruchprojekten. Auf dieser Basis werden Handlungsempfehlungen für die Gewinnung von hochwertigen RC-Gesteinskörnungen erarbeitet und diskutiert.----------------------------------------------------------------------------------------- Due to the large-scale mass flow of construction and demolition wastes, the recycling of those residues is of particular importance for the conservation of natural resources. An important requirement for recycling on a high level, like the reuse of crushed concrete as recycled concrete aggregate, is the observation of limits for hazardous substances and impurities. This study is focusing on the reduction of sulphates in the eluate of crushed concrete. An investigation of possibilities to optimize demolition and dismantling as well as treatment of crushed concrete with the objective of gaining recycled concrete aggregates of high quality. Based on a literature research and a data review the origins of sulfates in buildings and also the availability of techniques for demolition and treatment of crushed concrete are listed and evaluated. Using the examples of different building types scenarios for selective dismantling and non-selective demolition (focused on reducing suphates) are evaluated in terms of affecting the environment. In addition samples from real demolition construction sites and plants for treatment of construction rubble were investigated. Based on these results recommendations for the production of high quality recycled concrete aggregates are worked out. KW - Bauschuttaufbereitung KW - Abbruch KW - Ökobilanzielle Bewertung KW - RC-Beton KW - Gips KW - Abbruchverfahren KW - Hochwertiges Recycling KW - Ökobilanzielle Betrachtung KW - Sulfatentfachtung KW - Demolition/dismantling KW - Treatment of C&D wastes KW - High-grade recycling KW - Environmental LCA KW - Reduction of sulphates PY - 2012 UR - http://www.umweltbundesamt.de/publikationen/optimierung-des-rueckbausabbaus-von-gebaeuden-zur SN - 1862-4804 SP - 1 EP - 227 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-26999 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Götschel, S. A1 - Maierhofer, Christiane A1 - Weiser, M. T1 - Determining the material parameters for the reconstruction of CFRP specimens measured by flash thermography N2 - CFRP materials are progressively used in areas where the weight as well as the strength of materials matter. Since they are used in safety relevant environments, like aircrafts and cars, an assessment of the components for defects is mandatory. Flash thermography has proven to be a valuable tool to resolve defects. However, a quantitative evaluation of the defect extent and depth within the specimen is extremely challenging, since the commonly used analytical models do not incorporate lateral heat flow around the defect areas. Hence a reconstruction of the samples by numerical simulations is a path to improve the results. This finally enables pass and fail tests for specimens based on quantitative results. The properties of the anisotropic CFRP materials vary dependent on the matrix and fibre chosen. In addition the fabrication processes are distinct, hence it is strongly desirable to measure the properties of a sound sample in a fast and reliable way. The knowledge of diffusivity and heat capacity in three dimensions finally enables the simulation to improve modelling the specimen geometry. The in-plane diffusivity is determined by heating the sample with a laser line (a flat top profiled focused in one dimension) and monitoring the transient temperature at the front surface of the sample. This method is compared to measurements of the diffusivity using a Gaussian laser spot. The results are compared to results obtained by flash thermography in transmission. In addition the heating process of the sample on its surface as well the heat conduction is monitored using an IR-microscopic objective. Hence the transparency of the sample as well as the temperature conduction of the two components in microscopic scale can be studied. Finally the results are applied to provide precise parameters in the simulation of defects in a CFRP sample. It is gratefully acknowledged that the present work is funded by the DFG within the framework of the project WE 2937/6-1. T2 - QNDE, Review of Progress in Quantitative Nondestructive Evaluation CY - Atlanta, GA, USA DA - 17.07.2016 KW - Flash thermography KW - Reconstruction KW - Thermography KW - Quantitative nondestructive evaluation PY - 2016 AN - OPUS4-36977 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Götschel, S. A1 - Maierhofer, Christiane A1 - Müller, Jan P. A1 - Rothbart, Nick A1 - Weiser, M. T1 - Quantitative defect reconstruction in active thermography for fiber-reinforced composites T2 - 19th World Conference on Non-Destructive Testing 2016 N2 - Carbon-fiber reinforced composites are becoming more and more important in the production of light-weight structures, e.g., in the automotive and aerospace industry. Thermography is often used for non-destructive testing of These products, especially to detect delaminations between different layers of the composite. In this presentation, we aim at methods for defect reconstruction from thermographic measurements of such carbon-fiber reinforced composites. The reconstruction results shall not only allow to locate defects, but also give a quantitative characterization of the defect properties. We discuss the simulation of the measurement process using finite element methods, as well as the experimental validation on flat bottom holes. Especially in pulse thermography, thin boundary layers with steep temperature gradients occurring at the heated surface need to be resolved. Here we use the combination of a 1D analytical solution combined with numerical solution of the remaining defect equation. We use the simulations to identify material Parameters from the measurements. Finally, fast heuristics for reconstructing defect geometries are applied to the acquired data, and compared for their accuracy and utility in detecting different defects like back surface defects or delaminations. T2 - 19th World Conference on Non-Destructive Testing 2016 CY - München, Germany DA - 13.06.2016 KW - Active thermography KW - Numerical simulation KW - Time-resolved thermogram KW - Thermal wave PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-366644 UR - https://www.wcndt2016.com/Programme/show/Th-4-C-4 VL - 2016 SP - Th.4.C.4-1 EP - Th.4.C.4-10 AN - OPUS4-36664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Krankenhagen, Rainer T1 - Influence of the real energy input on the sensitivity of thermographic testing in case of GFRP N2 - Thermographic testing (TT) is an upcoming nondestructive method, which requires no contact at all to the specimen and can be applied on larger areas simultaneously. The measurement concept is based on the production of a thermal imbalance at the surface of the object under test. When the surface of this object is heated by an external source for a certain time, the surface temperature drops subsequently, influenced by inner defects of the sample. This leads to thermal contrasts at the surface. It is crucial that those contrasts are large enough to be detectable above the noise level. In a first approximation, the observed temperature contrast at a defect is proportional to the energy which was really introduced into the specimen during the heating period. However, the real energy input in a TT experiment is almost always unknown due to distinct parameters of the experimental setup or the material investigated. Typically, only the power consumption of the heating sources is reported, sometimes combined with the distance to the specimen surface. This contribution describes the thermographic inspection of a rear side thickness variation from 1 to 2 cm at GFRP. This could represent a rear side adhesive bond i.e. in a wind turbine rotor blade. The front side heating was realized by usual halogen lamps with variable radiation power. The detected temperature contrast at the front side will be related to the different energy inputs determined by means of a simple analytical model applied to the experimental data. Additionally, the experimental data are compared with results of FEM simulations performed by COMSOL Multiphysics. The results clearly demonstrate the key role of the real energy input in a real TT setup, if detection limits have to be evaluated. T2 - ECNDT 2018 CY - Göteborg, Sweden DA - 11.06.2018 KW - GFK KW - Thermografie mit Stufenanregung KW - Rotorblatt KW - Zerstörungsfreie Prüfung KW - Energieeintrag PY - 2018 AN - OPUS4-45374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Dell'Avvocato, G. A1 - Krankenhagen, Rainer T1 - Applying a two-layer quadrupole model for quantitative thermography at overload-induced delaminations in GFRP N2 - The applicability of 1D-quadrupole-model on the depth estimation of overload-induced delaminations is tested in this contribution. While classical 1D-methods like Pulsed Phase Transformation and Thermographic Signal Reconstruction determine the depth of a defect by one parameter, a two-layer quadrupole model provides two parameters: depth and thermal resistance. In addition, the convectional losses at the surfaces may be considered. The defect investigated is a large-scale delamination in glass fibre reinforced polymer generated by tension overload. T2 - Advanced Infrared Technology & Applications (AITA) CY - Florenz, Italy DA - 16.9.2019 KW - Aktive Thermographie KW - Nicht-lineare Regression KW - 1D-Simulation KW - GFK PY - 2019 AN - OPUS4-49133 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Jan Peter A1 - Dell'Avvocato, G. A1 - Krankenhagen, Rainer T1 - Assessing overload-induced delaminations in glass fiber reinforced polymers by its geometry and thermal resistance JF - NDT and E International N2 - The one-dimensional thermal quadrupole method is used to evaluate a pulsed thermography measurement at delaminations in a glass-fiber reinforced plastic plate quantitatively. The large-scale delaminations have been induced by tension overload and are air-filled and are usually located at the same depth as the notch bottom of a notch on the rear side. While classical evaluation methods like pulsed phase thermography and thermal Signal reconstruction are focused on the delamination depth only, the thermal quadrupole method determines spatially resolved two parameters for delaminations, delamination depth and local thermal resistance. Interestingly, lateral heat flows do not disturb this kind of depth evaluation. KW - Pulsed thermography KW - Delamination KW - Debond KW - Composite materials PY - 2020 DO - https://doi.org/10.1016/j.ndteint.2020.102309 VL - 116 SP - 102309 PB - Elsevier Ltd. AN - OPUS4-50937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Krankenhagen, Rainer T1 - Ein Blick unter die Oberfläche von Windkraftanlagen durch Thermografie N2 - Rotorblätter von Windkraftanlagen sind hohen Belastungen ausgesetzt. Nach Jahren der Nutzung können Klebeverbindungen unter der Oberfläche versagen. Thermografie soll die Zustandsüberwachung während der gesamten Lebensdauer verbessern. N2 - Rotor blades of wind power generators are subject to high strains. After years of use, adhesive bonds under the surface may fail. Thermography is intended to improve condition monitoring during the entire service life. T2 - Hannover Messe 2019 CY - Hanover, Germany DA - 1.4.2019 KW - Wiederkehrende Prüfung KW - Thermografie KW - Klebeverbindungen KW - Rotorblatt KW - GFK PY - 2019 AN - OPUS4-49160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Jan P. A1 - Götschel, S. A1 - Maierhofer, Christiane A1 - Weiser, M. T1 - Determining the Material Parameters for the Reconstruction of Defects in Carbon Fiber Reinforced Polymers from Data Measured by Flash Thermography JF - AIP Conference Proceedings N2 - Flash thermography is a fast and reliable non-destructive testing method for the investigation of defects in carbon fiber reinforced polymer (CFRP) materials. In this paper numerical simulations of transient thermography data are presented, calculated for a quasi-isotropic flat bottom hole sample. They are compared to experimental data. These simulations are one important step towards the quantitative reconstruction of a flaw by assessing thermographic data. The applied numerical model is based on the finite-element method, extended by a semi-analytical treatment of the boundary of the sample, which is heated by the flash light. A crucial part for a reliable numerical model is the prior determination of the material parameters of the specimen as well as of the experimental parameters of the set-up. The material parameters in plane and in depth diffusivity are measured using laser line excitation. In addition, the absorption and heat transfer process of the first layers is investigated using an IR microscopic lens. The performance of the two distinct components of CFRP during heating – epoxy resin and carbon fibers – is examined. Finally, the material parameters are optimized by variation and comparison of the simulation results to the experimental data. The optimized parameters are compared to the measured ones and further methods to ensure precise material parameter measurements are discussed. T2 - 43rd Review of Progress in Quantitative Nondestructive Evaluation CY - Atlanta, GA, USA DA - 17.07.2016 KW - Aktive Thermografie KW - Thermische Diffusivität KW - Zerstörungsfreie Prüfung KW - Kohlenstofffaserverstärkter Kunststoff KW - CFK KW - Active thermography KW - Thermal diffusivity KW - Non-Destructive testing KW - Carbon fiber reinforced polymer KW - CFRP PY - 2017 SN - 978-0-7354-1474-7 DO - https://doi.org/10.1063/1.4974671 SN - 0094-243X VL - 1806 IS - 1 SP - UNSP 100006-1 EP - 11 PB - AIP Publishing CY - Melville, NY, USA AN - OPUS4-39332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Götschel, S. A1 - Weiser, M. A1 - Maierhofer, Christiane T1 - Thermografie mit optimierter Anregung für die quantitative Untersuchung von Delaminationen in kohlenstofffaserverstärkten Kunststoffen T2 - DGZfP Jahrestagung 2017, 22.-24. Mai 2017, Koblenz N2 - Da kohlenstofffaserverstärkte Kunststoffe (CFK) in anspruchsvollen sicherheitsrelevanten Einsatzgebieten wie im Automobilbau und in der Luftfahrt eingesetzt werden, besteht ein zunehmender Bedarf an zerstörungsfreien Prüfmethoden. Ziel ist die Gewährleistung der Sicherheit und Zuverlässigkeit der eingesetzten Bauteile. Aktive Thermografieverfahren ermöglichen die effiziente Prüfung großer Flächen mit hoher Auflösung in wenigen Arbeitsschritten. Ein wichtiges Teilgebiet der Prüfungen ist die Ortung und Charakterisierung von Delaminationen, die sowohl bereits in der Fertigung als auch während der Nutzung eines Bauteils auftreten können, und dessen strukturelle Integrität schwächen. In diesem Beitrag werden CFK-Strukturen mit künstlichen und natürlichen Delaminationen mit Hilfe unterschiedlich zeitlich modulierter Strahlungsquellen experimentell untersucht. Verwendet werden dabei Anregungen mit Blitzlampen und mit frequenzmodulierten Halogenlampen. Mittels Filterfunktionen im Zeit- und Frequenzbereich wird das Kontrast-zu-Rausch-Verhältnis (CNR) der detektierten Fehlstellen optimiert. Verglichen werden anschließend die Nachweisempfindlichkeit, das CNR und die Ortsauflösung der zu charakterisierenden Delaminationen für die unterschiedlichen Anregungs- und Auswertungstechniken. Ergänzt werden die Experimente durch numerische Simulationen des dreidimensionalen Wärmetransportes. T2 - DGZfP Jahrestagung 2017 CY - Koblenz, Germany DA - 22.05.2017 KW - CFK KW - Contrast Noise Ratio KW - Lock-in Thermografie KW - Gepulste Thermografie KW - Kurzzeit-Fouriertransformation PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-404276 SN - 978-3-940283-85-6 VL - DGZfP BB 162 SP - Mi.1.A.4, 1 EP - 11 AN - OPUS4-40427 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. A1 - Götschel, S. A1 - Maierhofer, Christiane A1 - Weiser, M. T1 - Thermografie mit optimierter Anregung für die quantitative Untersuchung von Delaminationen in kohlenstofffaserverstärkten Kunststoffen N2 - Da kohlenstofffaserverstärkte Kunststoffe (CFK) in anspruchsvollen sicherheitsrelevanten Einsatzgebieten wie im Automobilbau und in der Luftfahrt eingesetzt werden, besteht ein zunehmender Bedarf an zerstörungsfreien Prüfmethoden. Ziel ist die Gewährleistung der Sicherheit und Zuverlässigkeit der eingesetzten Bauteile. Aktive Thermografieverfahren ermöglichen die effiziente Prüfung großer Flächen mit hoher Auflösung in wenigen Arbeitsschritten. Ein wichtiges Teilgebiet der Prüfungen ist die Ortung und Charakterisierung von Delaminationen, die sowohl bereits in der Fertigung als auch während der Nutzung eines Bauteils auftreten können, und dessen strukturelle Integrität schwächen. In diesem Beitrag werden CFK-Strukturen mit künstlichen und natürlichen Delaminationen mit Hilfe unterschiedlich zeitlich modulierter Strahlungsquellen experimentell untersucht. Verwendet werden dabei Anregungen mit Blitzlampen und mit frequenzmodulierten Halogenlampen. Mittels Filterfunktionen im Zeit- und Frequenzbereich wird das Kontrast-zu-Rausch-Verhältnis (CNR) der detektierten Fehlstellen optimiert. Verglichen werden anschließend die Nachweisempfindlichkeit, das CNR und die Ortsauflösung der zu charakterisierenden Delaminationen für die unterschiedlichen Anregungs- und Auswertungstechniken. Ergänzt werden die Experimente durch numerische Simulationen des dreidimensionalen Wärmetransportes. T2 - DGZfP Jahrestagung 2017 CY - Koblenz, Germany DA - 22.05.2017 KW - CFRP KW - CFK KW - Lock-In Thermografie KW - Blitz-Thermografie KW - Konstrast-Rausch-Verhältnis PY - 2017 AN - OPUS4-40566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Jan P. A1 - Krankenhagen, Rainer T1 - Optimizing thermographic testing of thick GFRP plates by assessing the real energy absorbed within the material JF - Composite Structures N2 - Active thermography is a well suited non-destructive testing method for the challenging inspection of wind rotor blades. Since the GFRP structures are up to some centimetres thick, long pulse heating is required to provide an appropriate energy input into the structure. So far, no best practice exists to guarantee a reliable detection of deep-lying flaws. In this work, a step wedge specimen having a maximum thickness of 34mm is systematically investigated by experiment and well-matched simulations to assess the influence of the experimental parameters, like the absorbed energy, on thermal contrasts. Finally, a scheme to conduct full-scale test of a wind rotor blade in less than three hours is proposed. KW - Pulsed thermography KW - Wind rotor blade KW - GFRP PY - 2019 DO - https://doi.org/10.1016/j.compstruct.2019.02.027 SN - 0263-8223 VL - 215 SP - 60 EP - 68 PB - Elsevier CY - Amsterdam AN - OPUS4-47396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pohl, Rainer A1 - Casperson, Ralf A1 - Maierhofer, Christiane A1 - Müller, Jan A1 - Pelkner, Matthias T1 - Gegenüberstellung von Wirbelstromprüfung und aktiver Thermografie an CFK-Versuchskörpern T2 - DGZfP-Berichtsband N2 - In vielen Bereichen der Technik haben Konstruktionen unter Einsatz von CFK-Bauteilen und Komponenten die klassischen Metalle abgelöst. Die zerstörungsfreie Prüfung solcher CFK-Bauteile gewinnt somit zunehmend an Bedeutung. Ein mögliches Prüfverfahren ist dabei die Wirbelstromprüfung. Aufgrund der relativ geringen elektrischen Leitfähigkeit von CFK-Komponenten kommt hierbei häufig die sogenannte HF-Wirbelstromprüfung zum Einsatz. In verschiedenen Untersuchungen der BAM konnten jedoch auch mit Wirbelstromprüfsystemen in niedrigen Frequenzbereichen gute Ergebnisse erzielt werden. Um die Möglichkeiten und Grenzen dieser konventionellen Wirbelstromprüfung auszuloten, wurden Messungen an Versuchskörpern durchgeführt, welche bereits bei der Validierung der Blitz- und Lock-in-Thermografie für neue Verfahrensnormen erfolgreich eingesetzt wurden. Ein Typ dieser Versuchskörper sind Flachproben aus CFK von 6 mm Dicke. In diesen wurden Flachbodenbohrungen mit Durchmessern zwischen 4 mm und 24 mm eingebracht. Die Restwandstärken liegen zwischen 0,06 mm und 3,66 mm. Ein weiterer CFK-Versuchskörper hat die Geometrie eines Stufenkeiles. Bei verschiedenen Stufenkeilen sind Wanddicken zwischen 1,4 mm und 5,4 mm realisiert worden. In diesen wurden künstliche quadratische Delaminationen mit Kantenlängen zwischen 2 mm und 20 mm eingebracht. Die Ergebnisse der Wirbelstromprüfung werden denen der aktiven Thermografie gegenübergestellt. Zur Nachbildung von Kompositwerkstoffen wurden die flachen Versuchskörper mit geeigneten Versuchskörpern aus Aluminium und Stahl kombiniert. Die Wirbelstromprüfungen wurden mit einem handelsüblichen Prüfgerät im Frequenzbereich zwischen 500 Hz und 3 MHz und entsprechend angepassten Sensoren durchgeführt. T2 - DGZfP Jahrestagung 2017 CY - Koblenz, Germany DA - 22.05.2017 KW - Wirbelstromprüfung KW - Aktive Thermografie KW - CFK PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-403607 SN - 978-3-940283-85-6 VL - 162 SP - 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-40360 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paul, Andrea A1 - Meyer, Klas A1 - Ruiken, Jan-Paul A1 - Illner, M. A1 - Müller, D.-N. A1 - Esche, E. A1 - Wozny, G. A1 - Westad, Frank A1 - Maiwald, Michael T1 - Process spectroscopy in microemulsions — Raman spectroscopy for online monitoring of a homogeneous hydroformylation process JF - Measurement Science and Technology N2 - A major industrial reaction based on homogeneous catalysis is hydroformylation for the production of aldehydes from alkenes and syngas. Hydroformylation in microemulsions, which is currently under investigation at Technische Universität Berlin on a mini-plant scale, was identified as a cost efficient approach which also enhances product selectivity. Herein, we present the application of online Raman spectroscopy on the reaction of 1-dodecene to 1-tridecanal within a microemulsion. To achieve a good representation of the operation range in the mini-plant with regard to concentrations of the reactants a design of experiments was used. Based on initial Raman spectra partial least squares regression (PLSR) models were calibrated for the prediction of 1-dodecene and 1-tridecanal. Limits of predictions arise from nonlinear correlations between Raman intensity and mass fractions of compounds in the microemulsion system. Furthermore, the prediction power of PLSR models becomes limited due to unexpected by-product formation. Application of the lab-scale derived calibration spectra and PLSR models on online spectra from a mini-plant operation yielded promising estimations of 1-tridecanal and acceptable predictions of 1-dodecene mass fractions suggesting Raman spectroscopy as a suitable technique for process analytics in microemulsions. KW - Raman KW - Online KW - Chemometrics KW - Hydroformylation KW - Mini-plant KW - Microemulsion PY - 2017 DO - https://doi.org/10.1088/1361-6501/aa54f0 SN - 1361-6501 SN - 0957-0233 VL - 28 IS - 3 SP - 035502-1 EP - 035502-11 PB - IOP Publishing Ltd CY - UK AN - OPUS4-39032 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -