TY - CONF A1 - Auersch, Lutz ED - Vogiatzis, Konstantinos T1 - Modes and waves of coupled roof or floor structures in historical and modern buildings N2 - Long wooden floor beams above a ball room in an old historical palace have been analysed experimentally. The eleven beams are weakly coupled by three layers of floor boards. It has been investigated if the state (the stiffness) of the wooden beams can be determined by vibration measurements of global or preferably local modes. Hammer, heel-drop and ambient excitations have been used. The vibration modes of the structure show dominating local deformations if an impact excitation is applied. This is understood as the positive superposition of several modes which yield the maximum at the excitation point but a cancellation at more distant points. Natural modes have been estimated from these vibration modes by standard and special methods which were necessary for the high damping of the wooden floor. It has been found that all floor beams contribute to each natural mode even for a weak coupling of the beams. In addition to the modal discussion, the impact tests have also been analysed for the wave propagation and amplitude attenuation with distance. The coupling of floor beams has been studied theoretically by an analytic multiple-beam model where the coupling by translational or rotational springs and by a common support motion has been assumed. T2 - 23. International Congress on Sound and Vibration CY - Athen, Greece DA - 10.07.2016 KW - modal analysis KW - floor vibration KW - wave analysis PY - 2016 SN - 978-960-99226-2-3 SN - 2329-3675 SP - Paper 318, 1 EP - 8 AN - OPUS4-37090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Modes and waves of coupled roof or floor structures in historical and modern buildings N2 - Long wooden floor beams above a ball room in an old historical palace have been analysed experimentally. The eleven beams are weakly coupled by three layers of floor boards. It has been investigated if the state (the stiffness) of the wooden beams can be determined by vibration measurements of global or preferably local modes. Hammer, heel-drop and ambient excitations have been used. The vibration modes of the structure show dominating local deformations if an impact excitation is applied. This is understood as the positive superposition of several modes which yield the maximum at the excitation point but a cancellation at more distant points. Natural modes have been estimated from these vibration modes by standard and special methods which were necessary for the high damping of the wooden floor. It has been found that all floor beams contribute to each natural mode even for a weak coupling of the beams. In addition to the modal discussion, the impact tests have also been analysed for the wave propagation and amplitude attenuation with distance. The coupling of floor beams has been studied theoretically by an analytic multiple-beam model where the coupling by translational or rotational springs and by a common support motion has been assumed. T2 - 23. International Congress on Sound and Vibration CY - Athen, Greek DA - 10.07.2016 KW - wave analysis KW - floor vibration KW - modal analysis PY - 2016 AN - OPUS4-37091 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The dynamic behavior of railway tracks with under sleeper pads, finite-element boundary-element model calculations, laboratory tests and field measurements N2 - Results from the calculation of the tracks have been presented. The compliances for the different under sleeper pads have been intensely discussed by the experts. Laboratory tests and field tests have been shortly presented to demonstrate the comprehensive approach of the BAM. N2 - Es werden die Arbeiten der BAM zu schweren Schwellen und weichen Schwellensohlen vorgestellt. Es wurden Berechnungen zum Schwingungsverhalten und zur Erschütterungsminderung durchgeführt. Laborversuche dienten dazu, die elstischen Eigenschaften der Schwellensohlen und die Dauerhaftigkeit der schweren Schwellen zu ermitteln. In Feldversuchen wurde die Minderungswirkung mit Schwingeranregung und mit Zuganregung ermittelt. T2 - Treffen "Schwellen und Schwellensohlen" CY - Berlin, Germany DA - 25.02.2016 KW - sleeper pads KW - railway track KW - ground vibration KW - mitigation PY - 2016 AN - OPUS4-37103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Realistic axle-load spectra for the prediction of ground vibrations form rail traffic N2 - Train passages induce static and dynamic forces on the track, the train-induced vibrations propagate through the soil and excite neighbouring buildings. The problem of train vibrations is divided into the parts emission, which is the excitation by railway traffic (the present contribution), transmission, which is the wave propagation through the soil, and immission, which is the transfer into a building, - The calculation of the axle loads are based on the vehicle-track-soil interaction. This interaction uses the dynamic stiffness of the vehicle (the inertia of the wheelset) and the dynamic stiffness of the track-soil System. Based on various time consuming finite-element boundary-element calculations, an approximate track-soil model has been established. The vehicle-track-soil analysis yields several transfer functions between the various geometric or stiffness irregularities and the axle loads of the train. Geometric irregularities of the vehicle (the wheels) and the track (rail surface and track alignment) are the simplest components. Geometric irregularities of the subsoil (trackbed irregularities) have to be transferred to effective irregularities at rail level. The bending stiffness of the track is filtering out the short-wavelength contribution. Stiffness irregularities occur due to random variations in the bailast or the subsoil, which must also be transferred to effective track irregularities, and due to the discrete rail support on sleepers. The axle loads due to the effective track errors from stiffness variations have their specific vehicle-track transfer function. - All necessary formula for the prediction of axle-load spectra will be presented. The prediction method is compared with axle-box measurements at a Standard ballasted track. Moreover, ground Vibration measurements at numerous sites are exploited for the axle-load spectra and the Validation of the prediction method. T2 - ICSV22 - 22nd International congress on sound and vibration CY - Florence, Italy DA - 12.07.2015 PY - 2015 SN - 978-88-88942-48-3 SN - 2329-3675 SP - 1 EP - 8 AN - OPUS4-33781 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Force and ground vibration reduction of railway tracks with elastic elements N2 - The reduction of train-induced ground vibration by elastic elements such as rail pads and sleeper pads has been analyzed by a combined finite-element boundary-element method. The dynamic compliance of the track, the transfer function of the total force on the ground and the ground vibration ratios have been calculated for a variety of isolated and un-isolated track systems. It has been found that the soil force transfer, which describes the excitation force of the soil, is an appropriate quantity to predict the reduction of the ground vibration and the effectiveness of isolated tracks. All force transfer functions of isolated tracks display a vehicle–track resonance where the wheelset on the compliant track is excited by wheel and track irregularities. At higher frequencies, considerable reductions of the amplitudes are observed as the benefit of the resilient element. The influence of the stiffness of the rail or sleeper pads, the ballast and the soil, and the mass of the sleeper and the wheelset on the resonance frequency and the reduction has been investigated. Sleeper pads are advantageous due to the higher mass that is elastically supported compared to the rail-pad track system. The combination of elastic rail and sleeper pads has been found to be disadvantageous, as the second resonance occurs in the frequency range of intended reduction. KW - Railway KW - Track KW - Rail pad KW - Sleeper pad KW - Force transfer KW - Ground vibration KW - Reduction PY - 2015 DO - https://doi.org/10.1177/1077546313507099 SN - 1077-5463 SN - 1741-2986 VL - 21 IS - 11 SP - 2246 EP - 2258 PB - Sage Science Press CY - Thousand Oaks, CA, USA AN - OPUS4-33682 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, M. ED - Papadopoulos, V. ED - Plevris, V. T1 - Fast computation of train-induced vibrations in homogeneous and layered soils N2 - The computation of the wave propagation in homogeneous and layered soils can be performed by a numerical integration in wavenumber domain. The numerical difficulties of an infinite integral and an integrand with poles can be solved. But if this computation must be repeated for many distances, many frequencies, many loads, or many soil models, it becomes a time consuming task which is not acceptable for a user-friendly prediction tool for railway induced ground vibration. Therefore, an approximate method for the computation of the wave field has been developed. The computation consists of several steps. At first, an approximate dispersion profile is calculated according to rules which have been derived from exact solutions. Secondly, the dispersion is used to achieve the amplitude for a certain frequency and a certain distance by calculating the approximate solution of a corresponding homogeneous half-space. Thirdly, three layer corrections are added which include lowfrequency near-field effects, high-frequency far-field effects, and a resonance amplification around the layer frequency. This procedure yields the wave field due to a point load. For a train load, many of these point-load responses have to be summed up, and a frequencydependant reduction factor has to be multiplied to incorporate the effect of the load distribution along and across the track. - The prediction method is applied to real sites, and the appropriate soil models are identified by approximating the measured transfer functions (frequency-dependant amplitudes) which is presented as an alternative to the approximation of the dispersion (frequency-dependant wave velocities). These examples demonstrate the general behavior of layered soils: the low amplitudes of the stiff half-space at low frequencies, the high amplitudes of the softer layer at high frequencies, the strong increase of amplitudes and a possible resonance amplification at mid frequencies. The material damping of the layer yields a strong attenuation of the amplitudes with the distance for high frequencies. The response depends strongly on the resonance or layer frequency which is shown for different layer depths and velocities always in good agreement with measurements. The layer frequency can be of immense influence if train-speed effects are analysed in a layered soil. The good agreement with many measurements in this contribution as well as in the references validates the prediction of ground vibration based on the theory of a layered half-space. T2 - COMPDYN 2015 - 5th International conference on computational methods in structural dynamics and earthquake engineering CY - Crete Island, Greece DA - 25.05.2015 PY - 2015 DO - https://doi.org/10.7712/120115.3381.959 SP - 66 EP - 82 AN - OPUS4-33683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Simultaneous measurements of the vehicle, track, and soil vibrations at a surface, bridge, and tunnel railway line N2 - A complex measuring campaign has been performed including the simultaneous measurement of vehicle, track, and soil vibrations during train runs at 16, 25, 40, 63, 80, 100, 125, 140, 160 km/h, and impulse measurements of the passenger car, three track sections and the soil. A ballast track on the soil surface and on a concrete bridge have been investigated as well as a slab track in a tunnel. The evaluation and comparison of all these data shows a generally good agreement for all components if the strong low- and high-frequency cut-off characteristics of the layered and damped soil are incorporated. There is a strong causal correlation between the vehicle and the soil by the dynamic excitation forces and a weak relation between the track and the soil by the axle-sequence spectrum of the train. However, the similarity between the axle-impulse spectrum observed at the track and the spectra of the ground vibration lead to the special excitation component of “scattered axle impulses” which is pre-dominant at the far-field points of the soil. KW - Railway KW - Ground vibration KW - Vehicle-track interaction KW - Track-soil interaction KW - Measurements PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-410224 DO - https://doi.org/10.1155/2017/1959286 VL - 2017 IS - ID 1959286 SP - 1 EP - 18 PB - Hindawi CY - Indien AN - OPUS4-41022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Auersch, Lutz T1 - A user-friendly prediction tool for railway induced ground vibrations: Emission - transmission - immission T2 - 9th IWRN - International Workshop on Railway Noise CY - Munich, Germany DA - 2007-09-04 PY - 2007 SP - S.4.2, 1 EP - 6 PB - International Workshop on Railway Noise CY - München AN - OPUS4-18592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamic stiffness of foundations on inhomogeneous soils for a realistic prediction of vertical building resonance N2 - The aim of this contribution is a practice-oriented prediction of environmental building vibrations. A Green's functions method for layered soils is used to build the dynamic stiffness matrix of the soil area that is covered by the foundation. A simple building model is proposed by adding a building mass to the dynamic stiffness of the soil. The vertical soil-building transfer functions with building-soil resonances are calculated and compared with a number of measurements of technically induced vibrations of residential buildings. In a parametrical study, realistic foundation geometries are modeled and the influence of incompressible soil, deep stiff soil layering, soft top layers, and increasing soil stiffness with depth is analyzed. All these special soil models reduce the resonant frequency compared to a standard homogeneous soil. A physically motivated model of a naturally sedimented soil has a stiffness increasing with the square root of the depth and yields a foundation stiffness that decreases with foundation area considerably stronger than the relatively insensitive homogeneous soil. This soil model is suited for the Berlin measuring sites and reproduces satisfactorily the experimental results. KW - Stiffness KW - Foundations KW - Predictions KW - Resonance KW - Vibration PY - 2008 DO - https://doi.org/10.1061/(ASCE)1090-0241(2008)134:3(328) SN - 1090-0241 SN - 1943-5606 VL - 134 IS - 3 SP - 328 EP - 340 PB - American Society of Civil Engineers CY - Reston, Va. AN - OPUS4-17394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - The effect of critically moving loads on the vibrations of soft soils and isolated railway tracks N2 - The dynamic response of the railway track is strongly influenced by the underlying soil. For a soft soil and very high train speeds or for a very soft soil and regular train speeds, the train speed can be close to the speed of elastic waves in the soil. This paper presents a detailed study of the so-called “moving-load effect”, i.e. an amplification of the dynamic response due to the load movement, for the tracks on soft soil. The analysis is carried out by evaluating the related integrals in the wavenumber domain. The influence of the load speed is quantified for a large set of parameters, showing that the effect on the soil vibration is reduced with increase of the frequency, track width and inverse wave velocity. Therefore, the moving-load effect associated with vibratory train loads is negligible whereas the amplification associated with the moving dead weight of the train can be significant. The strong moving-load effect on a perfectly homogeneous soil, however, can be strongly diminished by a layered or randomly varying soil situation. This theoretical result is affirmed by measurements at a test site in Germany where the trains run on a very soft soil at a near-critical speed. The results for soft soils are compared with experimental and theoretical results for a stiff soil. It is found that the influence of the stiffness of the soil is much stronger than the moving-load effect. This holds for the soil vibration as well as for the track vibration which both show a minor dependence on the load speed but a considerable dependence on the soil stiffness in theory and experiment. Railway tracks can include soft isolation elements such as rail pads, sleeper shoes and ballast mats. For these types of isolation elements and normal soil conditions, the influence of the load speed is usually negligible. There is only one isolation measure for which the moving load may be effective: a track which is constructed as a heavy mass–spring system. The resonance of this track system is shifted to lower frequencies and amplitudes for increasing train speed. A critical train speed can be reached if the mass–spring system has a marginal bending stiffness along the track. PY - 2008 DO - https://doi.org/10.1016/j.jsv.2007.10.013 SN - 0022-460X SN - 1095-8568 VL - 310 IS - 3 SP - 587 EP - 607 PB - Academic Press CY - London AN - OPUS4-17395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz ED - Tizani, W. T1 - Vibration of buildings on pile groups due to railway traffic - finite-element boundary-element, approximating and prediction methods N2 - A finite-element boundary-element software for the dynamic interaction of flexible structures and the soil has been extended for pile foundation. The boundary element method for the soil uses the Green´s functions of the layered half-space which have been generalised for interior loads. Pile groups of 10 to 20 piles of different arrays are analysed and compared with single piles. Simplified models have been developed for a user-friendly, practice oriented prediction software for railway induced ground and building vibration. T2 - ICCCBE 2010 - International conference on computing in civil and buildung engineering CY - Nottingham, UK DA - 2010-06-30 KW - Boundary elements KW - Soil-structure interaction KW - Pile foundations KW - Prediction software PY - 2010 SN - 978-1-907284-60-1 IS - Paper 275 SP - 549 EP - 554 PB - Nottingham University Press AN - OPUS4-21832 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Wave propagation in the elastic half-space due to an interior load and its application to ground vibration problems and buildings on pile foundations N2 - A method is presented which allows to calculate the wave-field in a homogeneous or layered soil in case of a dynamic interior load. The wave propagation along the surface, the distribution of the response over the depth, the horizontal propagation at different depths and the vertical downward propagation are shown and compared with the simpler surface solution of the half-space and the interior solution of the full-space. The complete wave-field (Green's function) is applied to the dynamic behaviour of piles and pile groups by use of a boundary element formulation. The stiffness, damping and – typically for piles – mass of different groups of piles are presented. Different group effects occur for lines, circles, grids, parallels and crosses of piles, which can be regarded as oscillations around average values. Moreover, the piles and pile groups behave almost like a damper for most of the frequencies. A building on a pile group that is excited by ground vibration due to surface or interior loads shows a reduction of the wave-field due to kinematic and inertial soil–building interaction effects. The results presented lead to simplified descriptions of the wave-field due to interior loads and of the soil–pile–building interaction which can be used for the prediction of technically induced vibration. KW - Wave propagation KW - Interior load KW - Dynamic pile and pile group stiffness KW - Kinematic and inertial soil-pile-building KW - Interaction PY - 2010 DO - https://doi.org/10.1016/j.soildyn.2010.04.003 SN - 0261-7277 SN - 0267-7261 VL - 30 IS - 10 SP - 925 EP - 936 PB - Elsevier Science CY - Amsterdam AN - OPUS4-21833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Two- and three-dimensional methods for the assessment of ballast mats, ballast plates and other isolators of railway vibration PY - 2006 SN - 1027-5851 VL - 11 IS - 4 SP - 167 EP - 176 CY - St. Petersburg, Russia AN - OPUS4-18953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Vehicle dynamics and dynamic excitation forces of railway induced ground vibration T2 - 21th International symposium on dynamics of vehicles on roads and tracks CY - Stockholm, Sweden DA - 2009-08-17 PY - 2009 SP - 1 EP - 12 CY - Stockholm, Sweden AN - OPUS4-21088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Theoretical and experimental excitation force spectra for railway-induced ground vibration: vehicle-track-soil interaction, irregularities and soil measurements N2 - Excitation force spectra are necessary for a realistic prediction of railway-induced ground vibration. The excitation forces cause the ground vibration and they are themselves a result of irregularities passed by the train. The methods of the related analyses - the wavenumber integration for the wave propagation in homogeneous or layered soils, the combined finite-element boundary-element method for the vehicle-track-soil interaction - have already been presented and are the base for the advanced topic of this contribution. This contribution determines excitation force spectra of railway traffic by two completely different methods. The forward analysis starts with vehicle, track and soil irregularities, which are taken from literature and axle-box measurements, calculates the vehicle-track interaction and gets theoretical force spectra as the result. The second method is a backward analysis from the measured ground vibration of railway traffic. A calculated or measured transfer function of the soil is used to determine the excitation force spectrum of the train. A number of measurements of different soils and different trains with different speeds are analysed in that way. Forward and backward analysis yield the same approximate force spectra with values around 1 kN for each axle and third of octave. KW - Railway forces KW - Vehicle-track interaction KW - Irregularities KW - Rail roughness KW - Track alignment KW - Wheel out-of-roundness KW - Ground vibration KW - Soil transfer function PY - 2010 DO - https://doi.org/10.1080/00423110802691515 SN - 0042-3114 VL - 48 IS - 2 SP - 235 EP - 261 PB - Taylor & Francis CY - Basingstoke, Hants. AN - OPUS4-22361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Technically induced surface wave fields, Part I: Measured attenuation and theoretical amplitude-distance laws N2 - The attenuation of the amplitudes with distance of technically induced surface wave fields is analyzed in theory and experiments. Experimental results of technically induced ground vibration are presented and collected from literature, which show a power-low attenuation A ~ r–q of amplitudes A with distance r and exponents q > 0.5 higher than for elastic surface waves. Additional attenuation effects are analyzed theoretically. The most important effect is due to the material or scattering damping. Each frequency component is attenuated exponentially as A ~ exp(–kr), but for a broadband excitation, the sum of the exponential laws yields a power law with a higher exponent. Some more effects are discussed, for example the dispersion of the Rayleigh wave due to the layering of the soil, which yields a stronger attenuation A ~ r–q–dq, including an additional exponent of dq = 0.5 in case of an impulsive loading. PY - 2010 DO - https://doi.org/10.1785/0120090228 SN - 0037-1106 SN - 1943-3573 VL - 100 IS - 4 SP - 1528 EP - 1539 PB - Seismological Society of America CY - El Cerito, Calif. AN - OPUS4-22405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Technically induced surface wave fields, Part II: Measured and calculated admittance spectra N2 - Transfer admittance spectra of technically induced surface wave fields are analyzed in theory and experiments. Theoretical admittance spectra of layered soils are obtained by integration in wavenumber domain and compared with experimental admittances due to hammer or vibrator excitation. The admittance spectra are strongly influenced by the layering and damping of the soil. Deep stiff-soil layers yield a low-frequency cutoff, whereas a strong damping yields a high-frequency cutoff. A sharp cutoff in a narrow frequency band, which is measured at some sites, can be explained by a damping that increases with frequency, such as viscous material or scattering damping. PY - 2010 DO - https://doi.org/10.1785/0120090229 SN - 0037-1106 SN - 1943-3573 VL - 100 IS - 4 SP - 1540 EP - 1550 PB - Seismological Society of America CY - El Cerito, Calif. AN - OPUS4-22406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamic interaction of various beams with the underlying soil - finite and infinite, half-space and Winkler models KW - Beam dynamics KW - Beam-soil interaction KW - Bending waves KW - Rayleigh wave KW - Railway track vibration KW - Elastic length KW - Wavenumber integrals PY - 2008 DO - https://doi.org/10.1016/j.euromechsol.2008.02.001 SN - 0997-7538 SN - 1873-7285 VL - 27 IS - 5 SP - 933 EP - 958 PB - Elsevier CY - Paris AN - OPUS4-17867 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz T1 - Static and dynamic soil-structure interaction of finite and infinite beams and plates, tracks and piles T2 - 7th European Conference on Structural Dynamics, EURODYN 2008 CY - Southampton, UK DA - 2008-07-07 KW - Soil-structure interaction KW - Wave-number integrals KW - Finite-element boundary-element method KW - Moving loads on tracks KW - Pile-soil interaction PY - 2008 SN - 9780854328826 IS - E 102 SP - 1 EP - 12 AN - OPUS4-18236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rücker, Werner A1 - Auersch, Lutz ED - Schulte-Werning, B. T1 - A user-friendly prediction tool for railway induced ground vibrations: Emission - transmission - immission T2 - 9th International Workshop on Railway Noise CY - Munich, Germany DA - 2007-09-04 PY - 2008 SN - 3-540-74892-X N1 - Serientitel: Notes on numerical fluid mechanics and multidisciplinary design – Series title: Notes on numerical fluid mechanics and multidisciplinary design IS - 99 SP - 129 EP - 135 PB - Springer CY - Berlin AN - OPUS4-18326 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz ED - Schulte-Werning, B. T1 - The influence of the soil on track dynamics and ground-borne vibration T2 - 9th International Workshop on Railway Noise CY - Munich, Germany DA - 2007-09-04 PY - 2008 SN - 3-540-74892-X N1 - Serientitel: Notes on numerical fluid mechanics and multidisciplinary design – Series title: Notes on numerical fluid mechanics and multidisciplinary design IS - 99 SP - 122 EP - 128 PB - Springer CY - Berlin AN - OPUS4-18327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Said, Samir A1 - Auersch, Lutz T1 - Environmental vibration due to normal and extreme excitation: railway traffic, explosions and heavy mass drop tests T2 - ISEV 2007, 3rd International Symposium on Environmental Vibrations: Prediction, Monitoring, Mitigation and Evaluation CY - Taipei, Taiwan DA - 2007-11-28 PY - 2007 SP - 1 EP - 6 AN - OPUS4-18408 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir T1 - Simple modal analysis and wave propagation for practical floor experiments in new and old office and residential buildings T2 - EVACES'07 - Experimental vibration analysis for civil engineering structures CY - Porto, Portugal DA - 2007-10-24 PY - 2007 SN - 978-972-752-095-4 SP - 423 EP - 432 AN - OPUS4-18409 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz T1 - Building response at foundation, walls, columns and floors due to ground vibration - simplified calculation based on experience with detailed models and measurements T2 - 16th International Congress on Sound and Vibration - ICSV16 CY - Kraków, Poland DA - 2009-07-05 PY - 2009 SN - 978-83-60716-71-7 SP - 1 EP - 8(?) AN - OPUS4-20474 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz A1 - Said, Samir ED - Xia, H. ED - Takemiya, H. T1 - Environmental vibrations due to different technical sources, amplitude-distance laws in experiment and theory T2 - 4th International Symposium on Environmental Vibration: Prediction, Monitoring and Evaluation (ISEV2009) CY - Beijing, China DA - 2009-10-28 KW - Amplitude-distance laws KW - Environmental vibrations KW - Field tests KW - Wave theory of attenuation PY - 2009 SN - 978-7-03-025765-9 VL - I SP - 757 EP - 762 PB - Science Press CY - Beijing, China AN - OPUS4-20788 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Building response due to ground vibration - simple prediction model based on experience with detailed models and measurements N2 - Construction work, such as pile driving and soil compaction, or road and railway traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for nearby inhabitants. A simplified building model has been created for these situations, which includes the effects of soil-structure interaction, the low-frequency amplification along the height of the building as well as the high-frequency reduction and the floor resonances. The model consists of one wall for all supporting structures (walls and columns) and one floor for each storey. The effect of different floor resonance frequencies is included in a stochastic procedure. The soil is modelled by a spring and a viscous damper, and the free-field amplitudes of the soil are applied under this soil element. The model can be calculated by transfer matrices or in a continuous wave-type version where an analytical solution can be evaluated numerically. The building response in the high-frequency (acoustic) region is calculated as mean values over wider frequency bands. The approach to an infinite building model can be found for these high frequencies and the corresponding soil-structure transfer can be described by the ratio of impedances at foundation level. The rules for choosing the parameters to obtain realistic results are derived from complex calculations for example, for the stiffness and damping of building foundations and many measurements as for the damping of floor resonances. The influences on the floor resonance from the soil (damping) and the supporting structure (detuning) are important. Some more effects will be discussed by the simplified and detailed models and by measurements to establish a good understanding of ground-induced building vibrations. PY - 2010 SN - 1027-5851 VL - 15 IS - 3 SP - 101 EP - 112 CY - St. Petersburg, Russia AN - OPUS4-22014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz A1 - Said, Samir T1 - Attenuation of ground vibrations due to different technical sources N2 - The attenuation of technically induced surface waves is studied theoretically and experimentally. In this paper, nineteen measurements of ground vibrations induced by eight different technical sources including road and rail traffic, vibratory and impulsive construction work or pile driving, explosions, hammer impulses and mass drops are described, and it is shown that the technically induced ground vibrations exhibit a power-law attenuation ν ~ r -q where the exponents q are in the range of 0.5 to 2.0 and depend on the source types. Comparisons performed demonstrate that the measured exponents are considerably higher than theoretically expected. Some potential effects on ground vibration attenuation are theoretically analyzed. The most important effect is due to the material or scattering damping. Each frequency component is attenuated exponentially as exp(-kr), but for a broad-band excitation, the sum of the exponential laws also yields a power law but with a high exponent. Additional effects are discussed, for example the dispersion of the Rayleigh wave due to soil layering, which yields an additional exponent of 0.5 in cases of impulsive loading. KW - Wave attenuation KW - Environmental vibrations KW - Field tests KW - Material damping KW - Scattering damping KW - Rayleigh wave PY - 2010 DO - https://doi.org/10.1007/s11803-010-0018-0 SN - 1671-3664 VL - 9 IS - 3 SP - 337 EP - 344 PB - Science Press CY - Beijing, China AN - OPUS4-22124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The influence of the track on railway induced ground vibration T2 - 30. Deutsche Jahrestagung für Akustik (DAGA) / 7 Congres Francais d'acoustique (CFA) CY - Strasbourg, France DA - 2004-03-25 PY - 2004 AN - OPUS4-3411 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Thompson, D. ED - Jones, C. T1 - Ground vibration due to railway traffic - the calculation of the effects of moving static loads and their experimental verification T2 - 8th International Workshop on Railway Noise CY - Buxton, England, UK DA - 2004-09-08 PY - 2004 VL - 1 SP - 119 EP - 129 CY - Buxton AN - OPUS4-4632 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Soil dynamics and tracks for high-speed traffic T2 - Workshop "Track Mechanics and Track Detoration" TU Berlin - BAM CY - Berlin, Germany DA - 1997-11-26 PY - 1997 AN - OPUS4-6606 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Some effects of the layering of the soil on wave propagation and foundation vibration T2 - 7th Conf. Soil Dynamics and Eartquake Engeneering CY - Crete, Greece DA - 1995-05-25 PY - 1995 AN - OPUS4-6609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Prospecting soft deposits by the analysis of the wave propagation in theory and experiment T2 - 3rd Int. Symposium on "Geotechnics Related to the European Environment" CY - Berlin, Germany DA - 2000-06-21 PY - 2000 AN - OPUS4-6610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Theory and experiments on wave propagation, on track-soil and on soil-building interaction related to railway induced vibration T2 - Fourth International Conference on Structural Dymanics (EURODYN 4) CY - Munich, Germany DA - 2002-09-02 PY - 2002 AN - OPUS4-6614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Vehicle-Track-Interaction and Soil Dynamics T2 - IAVSD-Conference "The Dynamics of Vehicles on Roads and Tracks" 115th Symposium Dynamics of Vehicles on Roads and Track (IAVSD) CY - Budapest, Hungary DA - 1997-08-25 PY - 1997 AN - OPUS4-6603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz ED - Cassereau, D. T1 - The influence of the track on railway induced ground vibration T2 - Joint Congress CFA/DAGA '04 ; 7e Congrès Français d'Acoustique ; 30. Deutsche Jahrestagung für Akustik ; Salon Européen de l'Acoustique ; Europäische Akustik-Austellung CY - Strasbourg, France DA - 2004-03-22 PY - 2004 SN - 2-9521105-2-2 VL - 2 SP - 1079 EP - 1080 PB - Société Française d'Acoustique (SFA) CY - Paris AN - OPUS4-3710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Ground vibration due to railway traffic - the calculation of the effects of moving static loads and their experimental verification T2 - 8th Workshop on Railway Noise and Vibration CY - Buxton, England DA - 2004-09-08 PY - 2004 AN - OPUS4-5448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Simplified methods for wave propagation and soil-structure interaction: the dispersion of layered soil and the approximation of FEBEM results T2 - Eurodyn 2005 CY - Paris, France DA - 2005-09-04 PY - 2005 AN - OPUS4-11876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - A practical method for the prediction of railway vibration T2 - Eurodyn 2005 CY - Paris, France DA - 2005-09-04 PY - 2005 AN - OPUS4-11879 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - The excitation of ground vibration by rail traffic: theory of vehicle-track-soil interaction and measurements on high-speed lines N2 - This article presents an integrated model for the computation of vehicle–track interaction and the ground vibrations of passing trains. A combined finite element and boundary element method is used to calculate the dynamic compliance of the track on realistic soil whereas multi-body models are used for the vehicle. The dynamic stiffness of the vehicle and that of the track are combined to calculate the dynamic axle loads due to the irregularities of the vehicle and the track as well as those due to sleeper passing excitation. These loads serve as input for the calculation of ground vibration near railway lines in the time and frequency domains. The theoretical methods and results have been proven by experiments in several respects and at several instances. First, on the occasion of the test and record runs of the Intercity Experimental, there was a very good quality of the vehicle and of the newly built track so that the deterministic parts of the excitation—the static load and the sleeper-passing component—could clearly be identified, the first being of minor importance apart from the track. Second, simultaneous measurements of the vehicle, the track and the soil at three different track situations were performed where we could verify the different parts of the stochastic excitation and their importance for the ground vibrations. The irregularities of the vehicle are dominant at high frequencies whereas the irregularities of the track are more important at lower frequencies. The comparison of the theory and the measurements also points to the phenomena of the vehicle–track resonance and the scattering of the quasi-static axle impulses by randomly varying soil. PY - 2005 DO - https://doi.org/10.1016/j.jsv.2004.06.017 SN - 0022-460X SN - 1095-8568 VL - 284 IS - 1-2 SP - 103 EP - 132 PB - Academic Press CY - London AN - OPUS4-11510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz A1 - Schmid, G. T1 - A simple boundary element formulation and its application to wavefield excited soil-structure interaction PY - 1990 SN - 0098-8847 SN - 1096-9845 SN - 0020-7160 VL - 19 SP - 931 EP - 947 PB - Wiley CY - London AN - OPUS4-11563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz ED - Brandes, K. ED - Vogel, A. T1 - Seismic response of three-dimensional structures using a green's function approach to the soil T2 - 2nd International Seminar on Earthquake Prognostics CY - Berlin, Germany DA - 1986-06-24 PY - 1986 SN - 3-528-06323-8 N1 - Serientitel: Progress in earthquake prediction research – Series title: Progress in earthquake prediction research IS - 3 SP - 393 EP - 403 PB - Vieweg CY - Braunschweig AN - OPUS4-11541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz A1 - Rücker, Werner ED - Klapperich, H. ED - Cazuffi, D. ED - Koerner, R. T1 - Dynamic loads of railway traffic T2 - ECI International Conference on The Use of Geosynthetics in Soil Reinforcement and Dynamics CY - Dresden, Germany DA - 2005-09-05 PY - 2005 SN - 3-7739-6003-4 SP - 433 EP - 443 PB - Verl. Glückauf CY - Essen AN - OPUS4-11547 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Structural dynamics and soil-structure-interaction induced by railway traffic T2 - Dynamics of Structures '89 CY - Karlovy Vary, Czech Republic DA - 1989-09-12 PY - 1989 SP - 21 EP - 25 AN - OPUS4-11554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holzlöhner, Ulrich A1 - Auersch, Lutz T1 - Propagation of Shock Waves at the Surface of Heterogeneous Soil Grounds PY - 1984 SN - 0363-9061 SN - 1096-9853 VL - 8 IS - 1 SP - 57 EP - 70 PB - Wiley CY - London AN - OPUS4-11503 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Dynamic Soil-Structure Interaction of Rigid and Flexible Foundations T2 - 5th International Conference on Soil Dynamics and Earthquake Engineering CY - Karlsruhe, Germany DA - 1991-09-23 PY - 1991 VL - 5 SP - 467 EP - 478 CY - Berlin AN - OPUS4-11569 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Wave propagation in layered soils: theoretical solution in wavenumber domain and experimental results of hammer and railway traffic excitation PY - 1994 SN - 0022-460X SN - 1095-8568 VL - 173 IS - 2 SP - 233 EP - 264 PB - Academic Press CY - London AN - OPUS4-11570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamics of the railway track and the underlying soil: the boundary-element solution, theoretical results and their experimental verification PY - 2005 SN - 0042-3114 VL - 43 IS - 9 SP - 671 EP - 695 PB - Taylor & Francis CY - Basingstoke, Hants. AN - OPUS4-11575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz ED - Soize, C. ED - Schueller, G. T1 - Simplified methods for wave propagation and soil-structure interaction: The dispersion of layered soil and the approximation of FEBEM results T2 - IMO-WIND: An integrated monitoring system for offshore wind energy turbines CY - Paris, France DA - 2005-09-04 PY - 2005 SN - 90-5966-033-1 SP - 1303 EP - 1308 PB - Millpress CY - Rotterdam AN - OPUS4-11576 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - A simple 2-dimensional method for the effectiveness of ballast mats and other isolators of railway vibrations T2 - 12. International Congress on Sound and Vibration CY - Lisbon, Portugal DA - 2005-08-11 PY - 2005 AN - OPUS4-11419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rücker, Werner A1 - Auersch, Lutz A1 - Gerstberger, Ulf A1 - Meinhardt, Christian ED - Soize, C. ED - Schueller, G. T1 - A practical method for the prediction of railway vibration T2 - IMO-WIND: An integrated monitoring system for offshore wind energy turbines CY - Paris, France DA - 2005-09-04 PY - 2005 SN - 90-5966-033-1 SP - 601 EP - 606 PB - Millpress CY - Rotterdam AN - OPUS4-11577 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz T1 - Some effects of the layering of the soil on wave propagation and foundation vibrations T2 - Soil dynamics and earthquake engineering VII CY - Southampton, England, UK DA - 1995-05-01 PY - 1995 SN - 1-85312-315-3 SP - 283 EP - 290 CY - Southampton AN - OPUS4-11579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamic plate-soil interaction - finite and infinite, flexible and rigid plates on homogeneous, layered or Winkler soil N2 - An integral method to calculate the solution of a homogeneous or layered soil due to a harmonic point load is described. An infinite plate at the surface of the soil can be introduced in this integration in wavenumber domain, too. Finite structures on the soil are calculated by a combined finite element and boundary element method, which makes use of the point load solution of the soil. The compliance functions for a vertical point load and some vibration modes are calculated for realistic parameters of the plate and the soil and for a wide range of frequencies. The influence of the stiffness of the soil and the foundation is investigated, showing that the soil mainly affects the low-frequent response whereas the structural properties are more important at higher frequencies. A rigid approximation of flexible plates is only found at low frequencies, if the elastic length is used as the radius of a rigid disk. At higher frequencies, a characteristic behaviour of the flexible plate of approximately is observed, what is in clear contrast to the compliance of rigid foundations. A plate on a visco-elastic support (Winkler soil) shows similar displacements as a plate on a homogeneous half-space, but the maximal stresses between the plate and the soil are considerably smaller which is found to be more realistic for a plate on a layered soil. For practical applications, a normalized diagram and some explicit formulas of the exact and the approximate solutions of an infinite plate on a homogeneous half-space are given, which is a useful model to represent the soil-structure interaction of flexible foundations. PY - 1996 DO - https://doi.org/10.1016/0267-7261(95)00021-6 SN - 0261-7277 SN - 0267-7261 VL - 15 IS - 1 SP - 51 EP - 59 PB - Elsevier Science CY - Amsterdam AN - OPUS4-11580 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Vehicle-track-interaction and soil dynamics T2 - 15th IAVSD Symposium Dynamics of Vehicles on Roads and Tracks CY - Budapest, Hungary DA - 1997-08-25 PY - 1998 SN - 0042-3114 VL - 29 SP - 553 EP - 558, Supplement PB - Taylor & Francis CY - Basingstoke, Hants. AN - OPUS4-11585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Structural dynamics and soil-structure-interaction induced by railway traffic T2 - Conference "Dynamics of Structures '89" CY - Karlovy Vary, Czech Republic DA - 1989-09-14 PY - 1989 AN - OPUS4-13759 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Dynamic soil-structure interaction of rigid and flexible foundations T2 - 5th Int. Conf. on Soil Dynamics and Earthquake Engineering CY - Karlsruhe, Germany DA - 1991-09-24 PY - 1991 AN - OPUS4-13760 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Seismic reponse of three-dimensional structures using a Green's function approach to the soil T2 - International Seminar on Earthquake Prognostics CY - Berlin, Germany DA - 1986-06-26 PY - 1986 AN - OPUS4-13753 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamic axle loads on tracks with and without ballast mats - numerical results of three-dimensional vehicle-track-soil models N2 - Ballast mats are an efficient measure to reduce the vibrations near railway lines. The vehicle-track system gets a low eigenfrequency due to the insertion of an elastic ballast mat under the ballast. For frequencies higher than this low vehicle-track eigenfrequency, the forces, which are generating the vibration of the soil, are considerably reduced. In this contribution, a combined finite-element boundary-matrix method is used to calculate a number of completely three-dimensional track models with and without ballast mats. The influence of the important parameters such as the stiffness of the ballast mat, the unsprung vehicle mass, the mass of the track, and the stiffness of the subsoil is investigated. The numerical results are presented as the transfer functions of the total force that is acting on the soil and generating the vibration of the environment. The effectiveness of ballast mats is achieved by division of two of these force functions. The general tendencies for this insertion loss are discussed and a comparison with measurements is given. To come to an improved practical tool for the design of ballast-mat tracks, the finite-element method results are approximated by a simple two-dimensional model of which the solution is given explicitly. KW - Railway track KW - Track dynamic KW - Ballast mat KW - Vibration isolation KW - Insertion loss KW - Finite-element method KW - Track-soil interaction KW - Vehicle-track interaction PY - 2006 DO - https://doi.org/10.1243/09544097F00105 SN - 0954-4097 VL - 220 IS - 2 SP - 169 EP - 183 PB - Institution of Mechanical Engineers CY - London AN - OPUS4-13723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Experimental observation and theoretical calculation of technically induced surface waves in inhomogeneous soil T2 - 1st European Conference on Earthquake Engineering and Seismology (ECEES) CY - Geneva, Switzerland DA - 2006-09-03 PY - 2006 IS - Paper 1292 SP - 1 EP - 10(?) PB - ETH Zürich CY - Geneva AN - OPUS4-13737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Moving load and reduction effects of tracks with and without isolation T2 - EUROMECH Colloquium 484 'Wave Mechanics and Stability of Long Flexible Structures Subject to Moving Loads and Flows' CY - Delft, Netherlands DA - 2006-09-19 PY - 2006 AN - OPUS4-13738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Experimental observation and theoretical calculation of technically induced surface waves in inhomogeneous soil T2 - 1st Europ. Conf. on Earthquake Engineering and Seismology CY - Geneva, Switzerland DA - 2006-09-03 PY - 2006 AN - OPUS4-13746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Ground vibration due to railway traffic - The calculation of the effects of moving static loads and their experimental verification N2 - The propagation of waves through homogeneous or layered soil is calculated based on half-space theory. The moving dynamic loads of a train are approximated by fixed dynamic loads and the wave field can be calculated if the spectrum of the dynamic train loads is known. In addition to this dynamic wave field, there are three different components at three different frequency ranges which are caused by the passage of the static loads: • the regular static component at low frequencies, • the irregular static component at medium frequencies, • the sleeper-passing component at high frequencies. For each of these components, an approximate solution is presented. The calculated wave field is compared with measurements of different trains at different sites. The measurement of impulse and harmonic point load excitation verifies the soil dynamic base of the method. PY - 2006 DO - https://doi.org/10.1016/j.jsv.2005.08.059 SN - 0022-460X SN - 1095-8568 VL - 293 IS - 3-5 SP - 599 EP - 610 PB - Academic Press CY - London AN - OPUS4-14049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Simple and advanced boundary-element method for the soil and its application to railway dynamics T2 - COMPDYN 2007, Computional Methods in Structural Dynamics and Earthquake Engineering CY - Rethymno, Greece DA - 2007-06-13 PY - 2007 AN - OPUS4-15003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - M. Papadrakakis, ED - D.C. Charmpis, ED - N.D. Lagaros, ED - Tsompanakis, Y. T1 - Simple and advanced boundary-element method for the soil and its application to railway dynamics T2 - COMPDYN 2007 CY - Rethymno, Crete, Greece DA - 2007-06-13 KW - Finite-element boundary-element method KW - Explicit Green´s functions KW - Track vibration KW - Tunnel vibration KW - Vehicle-track-soil interaction KW - Radiation damping PY - 2007 SP - 1 EP - 12 CY - Athen AN - OPUS4-15015 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The influence of the soil on track dynamics and ground-borne vibration T2 - 9th International Workshop on Railway Noise (IWRN) CY - Munich, Germany DA - 2007-09-04 PY - 2007 SP - S.4.1, 1 EP - 9 PB - International Workshop on Railway Noise CY - München AN - OPUS4-16438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, M. ED - Fragiadakis, M. ED - Plevris, V. T1 - High-speed railway tracks of a surface, bridge and tunnel line and some effects on the train-induced bridge and ground vibrations T2 - COMPDYN 2011 - 3rd International thematic conference - Computational methods in structural dynamics and earthquake engineering CY - Corfu, Greece DA - 2011-05-25 KW - Track compliance KW - Surface line KW - Bridge track KW - Tunnel track KW - Ground vibration KW - Layered soil KW - Bridge resonance KW - Train speed KW - Axle sequence KW - Track irregularities PY - 2011 SP - 1 EP - 17(?) AN - OPUS4-24555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - The dynamic force transfer of slab tracks and floating slab tracks and the corresponding ground vibration T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 2011-07-04 KW - Railway track KW - Slab track KW - Floating slab track KW - Track-soil interaction KW - Force transfer KW - Ground vibration PY - 2011 SN - 978-90-760-1931-4 SP - 820 EP - 827 AN - OPUS4-24556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir ED - Zhai, W. ED - Takemiya, H. ED - De Roeck, G. ED - Tutumluer, E. T1 - Experimental soil parameters by different evaluation methods for impulsive, train and ambient excitation T2 - ISEV 2011 - 5th International symposium on environmental vibration - Advances in environmental vibration CY - Chengdu, China DA - 2011-10-20 KW - Wave velocity KW - Dispersion KW - SASW KW - MASW KW - SPAC KW - Damping PY - 2011 SN - 978-7-03-032373-6 SP - 3 EP - 9 PB - Science Press AN - OPUS4-24807 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Náprstek, J. ED - Horácek, J. ED - Okrouhlík, M. ED - Marvalová, B. ED - Verhulst, F. ED - Sawicki, J.T. T1 - Reducing ground-borne micro-vibrations by plate foundations T2 - Vibration problems ICOVP 2011 - 10th international conference on vibration problems CY - Prague, Czech Republic DA - 2011-09-05 KW - Plate-soil interaction KW - Wave excitation KW - Vibration reduction KW - Finite-element boundary-element method PY - 2011 SN - 978-94-007-2068-8 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics VL - 139 SP - 329 EP - 335 PB - Springer AN - OPUS4-24804 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Dynamic behavior of slab tracks on homogeneous and layered soils and the reduction of ground vibration by floating slab tracks N2 - The dynamics of slab tracks and floating slab tracks are analyzed by multibeam models for the track and by integration in the wave-number domain for the soil, which is modeled as a layered half-space. Frequency-dependent compliances and force transfers are calculated for a great variety of track and soil parameters. The distribution of the load and the displacements along the track is investigated as well as the wave propagation perpendicular to the track and the ground vibration amplitudes. The floating slab track has a dominating plate-mat resonance and a strong high-frequency reduction. A track-soil resonance can also be recognized for an unisolated slab track in the case of layered soils. Generally, there is a strong damping of the track by the soil. The reduction effect of the slab mat is mainly owing to the elimination of this strong damping. The continuous soil yields slightly different rules for the displacements and force densities than those of a Winkler support. The total force transfer from the rail to the soil is the best criterion to judge the effectiveness of a floating slab track in reducing the ground vibration at some distance from the railway line. The total force transfer is easier to calculate than the double Fourier integrals of the ground vibration amplitudes, namely in the far field, and it has the best correlation with the reduction of the ground vibration. KW - Railway track KW - Slab track KW - Floating slab track KW - Track-soil interaction KW - Track vibration KW - Ground vibration KW - Force transfer PY - 2012 DO - https://doi.org/10.1061/(ASCE)EM.1943-7889.0000407 SN - 0733-9399 SN - 1943-7889 VL - 138 IS - 8 SP - 923 EP - 933 PB - Soc. CY - New York, NY, USA AN - OPUS4-26860 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Response to harmonic wave excitation of finite or infinite elastic plates on a homogeneous or layered half-space N2 - The soil–structure interaction of elastic plates on homogeneous or layered soils excited by horizontally propagating waves is analysed. Large plates are modelled by a combined finite-element boundary-element method (FEBEM), whereas the response of infinitely long plates is calculated by a numerical integration in the frequency–wavenumber domain. The finite-element boundary-element method yields the complete soil–plate transfer function of frequency and distance whereas the frequency–wavenumber solution of the infinitely long plate can serve as an approximation for long distances on a finitely long plate. The soil–plate transfer function starts to decrease strongly at the coincidence frequency, where the bending stiffness equals the plate inertia. A strong decrease follows at mid frequencies and a strong reduction of less than 0.1 of the ground vibration is reached at high frequencies. Rules for the characteristic frequencies are derived from the numerical results clearly indicating the strongest influence of the soil stiffness and the weaker influence of the bending stiffness of the plate. The influence of the mass, length and width of the plate are shown to be limited in case of realistic parameters, but it should be noted that the reduction effects are less effective for layered soils and for nearer observation points. KW - Plate-soil interaction KW - Wave excitation KW - Flexible plate KW - Layered soil KW - Vibration reduction KW - Finite-element boundary-element method KW - Frequency-wavenumber method PY - 2013 DO - https://doi.org/10.1016/j.compgeo.2013.02.001 SN - 0266-352x VL - 51 SP - 50 EP - 59 PB - Elsevier Appl. Sci. Publ. CY - Barking AN - OPUS4-27983 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Train induced vibration of inhomogeneous soils - a prediction based on measured and calculated point-load solutions N2 - Vehicle, track and ground vibration as well as their interaction are considered in a combined finite-element boundary-element (FEBEM) approach. The layered soil is calculated in frequency wavenumber domain and the solution for fixed or moving point or track loads follow as wavenumber integrals. The soil results from the measurements and the detailed models are approximated by simple formula which are used for the prediction of train-induced ground vibration. The influence of the track and the soil on the train induced ground vibration is analysed by the detailed models. The ground vibrations strongly depend on the regular and random inhomogeneity of the soil. The regular layering of the soil yields a cut-on and resonance phenomenon while the random inhomogeneity yields a scattering of the axle impulses which proved to be important for high-speed trains. The attenuation with distance of the ground vibration due to the point-like excitations such as vibrator or hammer excitations and the train-track excitation are investigated and compared. All theoretical results are compared with measurements at conventional and high-speed railway lines. T2 - ICSV19 - 19th International congress on sound and vibration CY - Vilnius, Lithuania DA - 08.07.2012 PY - 2012 SN - 978-609-459-079-5 SP - 1 EP - 8 AN - OPUS4-27218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, M. ED - Papadopoulos, V. ED - Plevris, V. T1 - How to quantify the vibration reduction of railway tracks N2 - Railway tracks, which reduce the ground vibration, are necessary if the trains are passing near to building. Today the reduction effect of railway tracks is often determined by the complex (time domain) simulation of the passage of a complete train. This method of evaluating the reduction is very time consuming and the results include some arbitrary scatter. It is worth to look for simpler methods which yield clearer results in shorter time. This contribution presents the combined finite-element boundary-element method as a detailed method for the track-soil interaction and, on the other hand, some possible simplifications. One important idea for the reduction assessment is to split the reduction in a vehicle-track interaction part and a track transfer part. The track transfer is not influenced by the vehicle and by single axle loads and it can be calculated as a homogeneous problem along the track. The reduction of some tracks (for example of floating slab tracks) can be dominated by this track transfer function whereas other tracks (for example tracks with soft rail pads) are completely determined by the vehicle-track-interaction part. The different force transfer functions and the ground vibration ratios of tracks with elastic rail pads or elastic sleeper pads are shown as a result of the FEBEM model under a fixed harmonic axle load. The force transfer proves to be a useful quantity for to assess the vibration reduction of railway tracks. T2 - COMPDYN 2013 - 4th ECCOMAS Thematic conference on computational methods in structural dynamics and earthquake engineering CY - Kos Island, Greece DA - 2013-06-12 KW - Railway induced ground vibration KW - Mitigation measures KW - Railway tracks KW - Finite-element boundary-element method KW - Wavenumber integrals KW - 1-D insertion loss PY - 2013 SP - 1 EP - 19 AN - OPUS4-29313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Rücker, Werner ED - Nielsen, J. T1 - Mitigation measures for ballasted tracks - optimisation of sleepers, sleeper pads and the substructure by combined finite-element boundary-element calculations T2 - IWRN11 - 11th International workshop on railway noise CY - Uddevalla, Sweden DA - 2013-09-09 PY - 2013 SP - 463 EP - 470 AN - OPUS4-29446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - How to quantify the vibration reduction of railway tracks T2 - Conference on Computational Methods in Structural Dynamics and Earthquake Engineering CY - Kos, Greece DA - 2013-06-11 PY - 2013 AN - OPUS4-29194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz A1 - Said, Samir A1 - Rücker, Werner ED - Sarsby, R. T1 - Prospecting soft deposits by wave propagation analysis in theory and experiment T2 - 3rd International Symposium on Geotechnics Related to the European Environment ; 3rd GREEN CY - Berlin, Germany DA - 2000-06-21 PY - 2001 SN - 0-7277-3004-5 SP - 65 EP - 73 PB - Telford CY - London AN - OPUS4-1594 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz A1 - Semrau, Norbert A1 - Schmid, Wolfgang A1 - Said, Samir A1 - Rücker, Werner ED - Grundmann, H. ED - Schuëller, G. I. T1 - Theory and experiments on wave propagation, on track-soil and on soil-building interaction related to railway induced vibration T2 - 5th International Conference on Structural Dynamics ; 4th International Conference on Structural Dynamics ; EURODYN 2002 CY - Munich, Germany DA - 2002-09-02 PY - 2002 SN - 90-5809-512-6 VL - 2 SP - 1137 EP - 1142 PB - Balkema CY - Lisse AN - OPUS4-1595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rücker, Werner A1 - Auersch, Lutz A1 - Baeßler, Matthias A1 - Knothe, K. A1 - Wu, Y. A1 - Gerstberger, Ulf A1 - Popp, K. A1 - Kruse, H. A1 - Savidis, S. ED - Popp, K. ED - Schiehlen, W. O. T1 - A comparative study of results from numerical track-subsoil calculations T2 - Colloquium 2002 CY - Stuttgart, Germany DA - 2002-03-13 PY - 2003 SN - 3-540-43892-0 N1 - Serientitel: Lecture notes in applied mechanics – Series title: Lecture notes in applied mechanics IS - 6 SP - 471 EP - 488 PB - Springer CY - Berlin AN - OPUS4-2358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Characteristic Frequencies of Train-Induced Bridge, Track, Ground and Building Vibrations – Excitation and Mitigation N2 - The characteristic frequencies of train-induced vibrations are discussed in theory and experiment following the propagation of vibrations from the source to the receiver: 1. Out-of-roundness frequencies of the wheels, 2. sleeper-passage frequency, 3. the vehicle-track eigenfrequency, 4. band frequency of the impulses of the passing static axle loads, 5. car-length frequency and multiples, 6. axle-distance frequencies with two characteristic zeros, 7. bridge eigenfrequencies, 8. the cut-on frequency due to the layering, and 9. the cut-off frequency due to the material damping of the soil, 10. the building-soil eigenfrequency, 11. as a rigid building or flexible wall/column mode, 12. floor eigenfrequencies, 13. acoustic room resonances, 14. the „resonance“ frequency or cut-off frequency of a base isolation. Coincidences of some of these characteristic frequencies or frequency ranges can be typically problematic and mitigation measures at the track or at the building can be necessary. The bridge response to the passing static loads is deter¬mined by the axle-sequence spectrum, the eigenfrequency (transfer function) of the bridge, and the modal force or mode shape spectrum. The ground vibration has typically high frequencies for a stiff soil and low frequencies for a soft soil. The high amplitudes between the zeros of the axle-sequence spectrum are often measured in the ground vibrations, and they can be mitigated by soft support elements or a higher bending stiffness of the track. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Train-induced vibration KW - Axle-sequence spectrum KW - Vehicle-track eigenfrequency KW - Axle impulses PY - 2025 AN - OPUS4-63654 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Mitigation of railway-induced ground vibration by soft support elements and a higher bending stiffness of the track N2 - The mitigation of train-induced ground vibrations by track solutions is investigated by calculations and measurements. The calculation by a wavenumber domain method includes the correct vehicle–track interaction and the correct track–soil interaction. Some theoretical results for elastic elements and an increased bending stiffness of the track are presented where the force transfer of the track and the vehicle–track interaction are calculated for the high-frequency dynamic mitigation, and the force distribution along the track is calculated for the low-frequency mitigation which is due to the smoother impulses from the passing static loads. Measurement results for the ground vibration near isolated and un-isolated tracks are given for several under-sleeper pads, for under-ballast mats, and for several under-ballast plates and ballast troughs. The elastic elements yield a resonance frequency of the vehicle–track–soil system and a high-frequency reduction of the dynamic axle loads which depends mainly on the softness of the pads or mats and which can be improved by a higher sleeper mass. In addition, all troughs and most of the soft elements show a low-frequency reduction which is attributed to the scattered impulses of the static axle loads. Besides this main contribution of the article, the problem of a soft reference section on a different soil is discussed and recommendations for better ground vibration measurements of mitigation effects are given. KW - Railway track KW - Elastic elements KW - Bending stiffness KW - Ground vibration KW - Mitigation KW - Lowfrequency reduction KW - Axle impulses PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612568 DO - https://doi.org/10.3390/app14031244 VL - 14 IS - 3 SP - 1 EP - 14 PB - MDPI CY - Basel AN - OPUS4-61256 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Some resonance effects of non-typical trains and railway bridges investigated by a frequency-domain method N2 - The resonances of railway bridges have often been analysed for short bridges under periodical high-speed trains, for simply supported one-span bridges, for the fundamental bridge mode, and by time-domain analyses. Many time-consuming calculations have been performed to establish simplified rules for standards. In this contribution, the passage of different (existing, new and hypothetic) trains over different (simply supported, integral, multi-span, continuous) bridges will be analysed in frequency domain by using three separated spectra with the purpose to get a better physical insight in the phenomena. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of an arbitrary train which is not limited to periodical or specific (conventional, articulated, regular or standard) trains and which does not include any bridge parameters. The final solution in frequency domain is obtained as the product of these three complex, strongly varying spectra for the dominating bridge mode or in general as the sum of these products over all relevant bridge modes. The time domain solution is obtained via the inverse Fourier transform, and the resulting time histories have been successfully compared with some measurement results. The method is applied to the vertical and torsional modes of a mid-long single-span bridge on elastomeric bearings under standard train speeds, to a short two-span bridge under high-speed traffic, and to a long three-span integral bridge under long periodical freight trains. Different resonance and cancellation effects have been found for systematically varied train speeds according to the axle sequence of the whole train which is dominated by the two locomotives in that case. To be more specific, the first torsional mode of the mid-span bridge is excited for a train speed of 100 km/h whereas the second bending mode is excited for a train speed of 160 km/h. In both cases, the other mode is suppressed by the minima of the axle-distance spectra. In addition, the case of the German high-speed train ICE4, a Maglev train on a viaduct, and the very high-speed hyperloop case will be discussed briefly. In general, it is shown that resonance effects are also worth to be studied for freight and passenger trains with lower speeds. KW - Rail bridge KW - Resonance KW - ICE4 KW - MAGLEV KW - Hyperloop KW - Continuous bridge KW - Multi-span bridge PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612595 DO - https://doi.org/10.1088/1742-6596/2647/25/252014 VL - 2647 SP - 1 EP - 11 PB - IOP Publishing AN - OPUS4-61259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Railway vibration – fast physics-based models for the prediction of ground vibration and the identification of track damage N2 - The following applications of machine learning will be discussed: 1. The prediction of the wave propagation from a railway line (completely physics based for surface lines, physics-based machine learning for tunnel lines) 2. The track behaviour for the emission of train-induced ground vibration (physics based for homogeneous soil, machine learning for layered soil) 3. Track damage detection and quantification from frequency response functions and moving load responses 4. Bridge damage detection and localisation from modal analysis and moving load 5. The use of axle-box acceleration for the identification of track/sub-soil condition and bridge resonances. The prediction of railway vibration usually needs time-consuming finite element, boundary element and wavenumber domain calculations. For a user-friendly prediction software however, fast calculations are needed. Several time-consuming detailed calculations have been used to develop simpler and fast models for the surface railway lines. The more challenging prediction from tunnel lines will be attacked by purely mathematical and by physics-informed machine learning. The dynamic stiffnesses of isolated or un-isolated railway tracks from detailed calculations with a continuous soil have been approximated with the simpler Winkler soil. The vehicle-track resonance (P2 resonance) rules the effect of the mitigation measures, and it can also be used for the on-board monitoring of the track and sub-soil condition. For the identification of track damage such as gaps between sleepers, track slabs and layers, detailed models with a continuous soil have been updated to get the best fit to the measured frequency response functions from hammer tests and the deformation pattern from the moving load response. Whereas the track damage can be locally identified, this is more difficult for bridges where the modal analysis gives mainly global information. The influence lines of the inclination for statically passing vehicles (locomotive, truck, compaction roller) have been used to localise bridge damage (stiffness variations). The on-board monitoring of rail bridges needs special conditions (regular trains with special speeds) to excite and measure the bridge resonance. T2 - 11th European Workshop on Structural Health Monitoring (EWSHM 2024) CY - Potsdam, Germany DA - 10.06.2024 KW - Vibration prediction KW - Track damage detection KW - Human and machine learning KW - Wave propagation KW - Surface line KW - Tunnel KW - Bridge resonance PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612462 DO - https://doi.org/10.58286/29865 SN - 1435-4934 SP - 1 EP - 9 PB - NDT.net CY - Kirchwald AN - OPUS4-61246 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, Manolis T1 - Frequency-wavenumber method for the wave propagation through the soil and the soil-structure interaction of railway tracks and building foundations near railway lines N2 - In soil-structure interaction, the soil and the (flexible) structures are modelled as elastic continua. The partial differential equations of elasticity can be transformed to algebraic equations in frequency-wavenumber domain where they can be solved by matrix methods. The results for the soil and a structure can be coupled in frequency-wavenumber domain, and the solution in space domain is obtained by an infinite wavenumber integral (the back-transformation). This method has several applications for the prediction of the emission, transmission and immission of railway-induced vibrations. The wave propagation in homogeneous or layered soils is calculated for surface and tunnel lines by a single wavenumber integration (transmission). The response of ballast or slab tracks (for the emission problem) and the foundation stiffness (for the immission problem) need an additional integration across the track or foundation width. In wavenumber domain, tracks and foundations of infinite length are analysed. Finite structures can be calculated by finite element models where the soil is calculated by the boundary element method. The Green’s functions for the boundary element method are calculated by a wavenumber integration as for the transmission problem. Some example results for all these tasks will be shown. The immission into buildings will be analysed in detail, and the effect of stiff slab foundations and (basement) walls on the incoming wavefield is quantified in a parameter study. The transfer function (the amplitude ratio) structure to free field usually starts with 1 at 0 Hz and decreases continuously with frequency. The reduction is due to the structural stiffness against wave deformation which turns to be higher than the stiffness of the soil, for example above the structure-soil coincidence frequency of the slab foundation. The reduction is better for a high structural stiffness and for a low soil stiffness. Walls are stiffer than plates for the relevant frequency range, but even walls and especially low basement walls are not infinitely rigid and can follow the wave deformation to a certain extent. These basic rules from frequency-wavenumber analysis can well be used for real building projects near railway lines where stiff foundations can be an alternative reduction method to the commonly used base isolation by elastic elements. T2 - COMPDYN 2025 CY - Rhodos, Greece DA - 15.06.2025 KW - Frequency-wavenumber method KW - Wave propagation KW - Soil-structure interaction KW - Building foundations KW - Mitigation measures PY - 2025 SP - 1 EP - 15 PB - NTUA CY - Athen AN - OPUS4-63470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Frequency-wavenumber method for the wave propagation through the soil and the soil-structure interaction of railway tracks and building foundations near railway lines N2 - In soil-structure interaction, the soil and the (flexible) structures are modelled as elastic continua. The partial differential equations of elasticity can be transformed to algebraic equations in frequency-wavenumber domain where they can be solved by matrix methods. The results for the soil and a structure can be coupled in frequency-wavenumber domain, and the solution in space domain is obtained by an infinite wavenumber integral (the back-transformation). This method has several applications for the prediction of the emission, transmission and immission of railway-induced vibrations. The wave propagation in homogeneous or layered soils is calculated for surface and tunnel lines by a single wavenumber integration (transmission). The response of ballast or slab tracks (for the emission problem) and the foundation stiffness (for the immission problem) need an additional integration across the track or foundation width. In wavenumber domain, tracks and foundations of infinite length are analysed. Finite structures can be calculated by finite element models where the soil is calculated by the boundary element method. The Green’s functions for the boundary element method are calculated by a wavenumber integration as for the transmission problem. Some example results for all these tasks will be shown. The immission into buildings will be analysed in detail, and the effect of stiff slab foundations and (basement) walls on the incoming wavefield is quantified in a parameter study. The transfer function (the amplitude ratio) structure to free field usually starts with 1 at 0 Hz and decreases continuously with frequency. The reduction is due to the structural stiffness against wave deformation which turns to be higher than the stiffness of the soil, for example above the structure-soil coincidence frequency of the slab foundation. The reduction is better for a high structural stiffness and for a low soil stiffness. Walls are stiffer than plates for the relevant frequency range, but even walls and especially low basement walls are not infinitely rigid and can follow the wave deformation to a certain extent. These basic rules from frequency-wavenumber analysis can well be used for real building projects near railway lines where stiff foundations can be an alternative reduction method to the commonly used base isolation by elastic elements. T2 - COMPDYN 2025 CY - Rhodos, Greece DA - 15.06.2025 KW - Frequency-wavenumber method KW - Wave propagation KW - Soil-structure interaction KW - Building foundations KW - Mitigation measures PY - 2025 AN - OPUS4-63468 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Prediction of ground vibrations from rail tunnels finite element, boundary element and wavenumber calculations N2 - The prediction of ground and building vibrations has been established for surface lines and has now been extended to tunnel lines. The wave propagation in homogeneous or layered soils (the transmission) is calculated by an integration in wavenumber domain. The wave amplitudes at different distances and for different frequencies will be analysed for the following situations. 1. The horizontal propagation from a surface point to a surface point constitutes the basic rules. 2. The horizontal propagation from a source point at depth to a receiver point at depth which is related to a building with a deep basement or on a pile foundation. 3. The propagation from depth to the surface, which is the normal case for free-field measurements, has some different characteristics, for example a weaker attenuation with the horizontal distance from the source, which can be approximated by the full-space solution and the reflection rules for incident waves. The emission from a tunnel structure has been calculated by a finite-element model of the tunnel combined with a boundary-element model of the soil giving the reduction compared to a point-load excitation. The immission has been analysed by finite-element models of tunnel-soil-building systems for examples of research and consultancy work. Measurement results from a high-speed and a metro line confirm some of the established rules. T2 - Recent Advance in Structural Dynamics (RASD) CY - Southampton, UK DA - 01.07.2024 KW - Ground vibration KW - Building vibration KW - Railway tunnel KW - Wavenumber method KW - Finite element method KW - Boundary element method PY - 2024 AN - OPUS4-61230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Railway-induced ground and building vibrations – Analysis in frequency-wavenumber domain and fast prediction with approximate models N2 - A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included. T2 - ISMA-Conference 2022 CY - Leuven, Belgium DA - 12.09.2022 KW - Ground vibration KW - Simple prediction KW - Vehicle-track interaction KW - Layered soil KW - Soil-building interaction KW - Soil-wall-floor model KW - Propagation from a tunnel KW - Tunnel-pile transfer PY - 2022 SP - 1 EP - 13 PB - KU Leuven CY - Leuven AN - OPUS4-56603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Auersch, Lutz T1 - Mitigation measures for slab tracks - wide sleepers on soft pads and different slabs - Results from the finite element boundary element method N2 - The ground vibrations, which are generated by trains on different slab tracks, have been calculated by finite-element boundary-element models. The slab track is modelled in detail by the finite element method. The infinite soil is modelled by the boundary element method as a homogeneous half-space. The track-soil system is coupled with a simple rigid mass model of the vehicle so that the vehicle-track interaction is completely included. Transfer functions are calculated in frequency domain without and with vehicle-track interaction, the compliance of the track and the mobilities of the soil at different distances from the track. Finally, the ratios between the ground vibration amplitudes with and without mitigation measure are calculated to quantify the effectiveness of the mitigation measure. Tracks with under sleeper pads have been investigated in a parameter study. The main parameter that influences the reduction of ground vibration is the stiffness of the under sleeper pad. The softest sleeper pad yields the best reduction of the ground vibration. The influence of other parameters has been examined. The stiffness of the rail pads, the stiffness of the slab material, the stiffness of the sleeper material, and the distance of the sleepers. All these parameters show no or only a minor influence on the mitigation effect. As the standard isolated track, a track with an under sleeper pad of a stiffness of kS = 5 107 N/m has been chosen, which can also be expressed as a stiffness per area of kS ’’ = 3.7 107 N/m3 = 0.037 N/mm3. The resonance frequency for this pad stiffness is observed between 32 and 40 Hz. The reduction of the ground vibration is about vi,I /vi,U = 0.1 at 100 Hz. KW - Wide sleeper KW - Under sleeper pad KW - Finite-element boudnary-element method KW - Slab track KW - Mitigation KW - Ground vibration PY - 2012 SP - 1 EP - 50 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-56608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir A1 - Rohrmann, R. T1 - Measurement and evaluation tools for ground and building vibrations from industrial pro-cesses, construction work, traffic and other sources N2 - Vibration measurements have many causes and many technical and natural sources. Problems can sometimes be solved by short-term measurements, but in many cases, a long-term measurement is necessary. In long-term measurements of days, weeks, months and even years, it is easy to collect a huge quantity of raw data, but at the end, the post-processing of these data can be exhausting (for example one-year vibration data of a wind energy tower). A software has been developed which con-sists of measuring and evaluation routines where the measuring routines can operate different meas-uring systems and different measuring cards. The main advantage of this software is the fact that the interesting evaluations can be integrated in the measuring process so that the characteristics of the vibration can be extracted without storing all the raw data. Only important time segments are stored, for example train passages. The overall concept of the software and the main evaluation routines will be described in some details. Examples of our measurement experience will illustrate the capabilities of the software. 1) Surveying construction work in nearby sensitive buildings (for example an old wind tunnel), including a stable alarm system and meaningful vibration limits. 2) Prediction of train-induced vibration for a planned building to prevent annoyance and to improve the building design. 3) Modal analysis and long term measurements of several single- or multi-span, concrete or steel bridges 4) Modal and wave analysis of coupled floors in a historical building (“Neues Palais” at Potsdam). 5) Soil properties of various measurement sites (different routines to evaluate the dispersion). Moreover, from many projects, amplitudes, frequencies, and attenuation laws have been collected and analysed for the different sources such as vibratory or impact pile driving and ground compaction, demolition work with different machines, blasting in quarries and in tunnel works, bomb and mine clearing. T2 - 28th International Congress on Sound and Vibration CY - Online meeting DA - 24.07.2022 KW - Ground vibration KW - Building vibration KW - Measurement KW - Evaluation KW - Modes KW - Waves PY - 2022 SP - 1 EP - 8 AN - OPUS4-56602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Effects of a varying track and soil stiffness on ground vibrations near railway lines N2 - Usually, geometric irregularities are considered as the main cause of ground vibrations from trains. A varying stiffness of the track, the track support and the soil can also generate ground vibrations. The regular stiffness variation of the track on and between the sleepers results in a deterministic dynamic axle load. The random stiffness variation of the track support yields also dynamic axle loads which are generated by the acceleration of the unsprung mass (from the varying wheel displacements under the static axle load). The random stiffness variation has a second effect. The pulses from the passage of the static axle loads are superposed regularly to the quasi-static response, but also irregularly to yield a “scattered” part of the axle pulses. The same holds for a random variation of the soil stiffness. All these effects of stiffness variations have been calculated by wavenumber-domain multi-beam track models, a random finite-element soil model and the superposition of axle impulses in a stochastic simulation. The results are confronted with many measurements at different sites. It is concluded that the stiffness variation of the track and the soil generate an important ground vibration component near railway lines. T2 - International Conference Railways 2022 CY - Montpellier, France DA - 22.08.2022 KW - Ground vibration KW - Axle loads KW - Irregularities KW - Varying stiffness PY - 2022 SP - 1 EP - 11 AN - OPUS4-56605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - The dynamic train-track interaction on a bridge and in a tunnel compared with the simultaneous vehicle, track, and ground vibration measurements at a surface line N2 - The vehicle–track interaction generates forces and consequently vibrations in the environment. The interaction has been analysed by the simultaneous measurements of vehicle, track and ground vibrations during test runs with varied train speeds. The special effects of the passage over a bridge and through a tunnel are studied and compared with the measurements on a conventional ballasted surface line. The maximum amplitudes, narrow band and one-third octave band spectra are presented for the axle-box accelerations and for the track, bridge and ground vibrations. The different frequencies and frequency bands are related to wheel out-of-roundness, track alignment errors, the sleeper passage and the wheelset–track resonance. An axle impulse component has been observed at the track, at the near-field soil and as a scattered version in the far field. Specific results can be found for the bridge track, where clearly speed-dependent bridge resonances occur due to the axle sequence of the train, and for the tunnel track where soft rail pads are responsible for a strong amplification around the wheelset–track resonance. On the other hand, the axle impulses are strongly reduced by the tunnel track, and the scattered axle impulse component is not as relevant as for the surface track. As a consequence, a strong mid-frequency amplitude reduction of the tunnel compared to the surface line has been measured for low and high train speeds by the Federal Institute of Material Research and Testing (BAM) and by other institutes. KW - Vehicle–track interaction KW - Ground vibration KW - Tunnel-to-surface reduction KW - Bridge resonance KW - Axle sequence PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-585139 DO - https://doi.org/10.3390/app131910992 VL - 13 IS - 19 SP - 1 EP - 23 PB - MDPI CY - Basel, Schweiz AN - OPUS4-58513 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Soil–structure interaction and damping by the soil - effects of foundation groups, foundation flexibility, soil stiffness and layers N2 - In many tasks of railway vibration, the structure, that is, the track, a bridge, and a nearby building and its floors, is coupled to the soil, and the soil–structure interaction and the damping by the soil should be included in the analysis to obtain realistic resonance frequencies and amplitudes. The stiffness and damping of a variety of foundations is calculated by an indirect boundary element method which uses fundamental solutions, is meshless, uses collocation points on the boundary, and solves the singularity by an appropriate averaging over a part of the surface. The boundary element method is coupled with the finite element method in the case of flexible foundations such as beams, plates, piles, and railway tracks. The results, the frequency-dependent stiffness and damping of single and groups of rigid foundations on homogeneous and layered soil and the amplitude and phase of the dynamic compliance of flexible foundations, show that the simple constant stiffness and damping values of a rigid footing on homogeneous soil are often misleading and do not represent well the reality. The damping may be higher in some special cases, but, in most cases, the damping is lower than expected fromthe simple theory. Some applications and measurements demonstrate the importance of the correct damping by the soil. KW - Soil–structure interaction KW - Soil dynamics KW - Radiation damping of the soil KW - Rigid foundation KW - Flexible foundation KW - Foundation groups KW - Boundary element method KW - Vibration measurement PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627007 DO - https://doi.org/10.3390/vibration8010005 SN - 2571-631X VL - 8 IS - 5 SP - 1 EP - 28 PB - MDPI CY - Basel, Schweiz AN - OPUS4-62700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Prediction of ground vibrations from rail tunnels –finite-element, boundary-element and wavenumber calculations N2 - The prediction of ground and building vibrations has been established for surface lines and has now been extended to tunnel lines. The wave propagation in homogeneous or layered soils (the transmission) is calculated by an integration in wavenumber domain. The wave amplitudes at different distances and for different frequencies will be analysed for the following situations. 1. The horizontal propagation from a surface point to a surface point constitutes the basic rules. 2. The horizontal propagation from a source point at depth to a receiver point at depth which is related to a building with a deep basement or on a pile foundation. 3. The propagation from depth to the surface, which is the normal case for free-field measurements, has some different characteristics, for example a weaker attenuation with the horizontal distance from the source, which can be approximated by the full-space solution and the reflection rules for incident waves. The emission from a tunnel structure has been calculated by a finite-element model of the tunnel combined with a boundary-element model of the soil giving the reduction compared to a point-load excitation. The immission has been analysed by finite-element models of tunnel-soil-building systems for examples of research and consultancy work. Measurement results from a high-speed and a metro line confirm some of the established rules. KW - Railway tunnel KW - Ground vibration KW - Building vibration KW - Wavenumber integral KW - Full-space solution KW - Reflection at the surface PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627015 DO - https://doi.org/10.1088/1742-6596/2909/1/012013 SN - 1742-6596 VL - 2909 SP - 1 EP - 12 PB - IOP Publishing CY - London AN - OPUS4-62701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Modal analysis of road and rail bridges for damage detection and resonance prediction N2 - In the 1980s, the Federal Institute of Material Research and Testing started with modal analysis measurements of some bridges before and after repair. For one of the bridges, a structural health monitoring was installed 1994 which is still working up to now. It has been modified and extended several times. The monitoring was extended from the critical span to three neighbouring spans. A modal analysis of the whole bridge with seven spans have been done three times, twice together with EMPA of Switzerland. Additional calibration measurements have been done and additional evaluation procedures have been implemented for the monitoring of the steadily increasing loads from the road traffic. Additional sensors were installed such as strain gauges, crack-width, and temperature sensors. The strong influence of the temperature on the natural frequencies has been studied over the years. Later, a temperature compensation has been established and a weak aging trend has been found in the monitoring data. Now, the bridge will be demolished and replaced by a new bridge. Some results of this long-term monitoring will be shown and possible damages (changes of the pre-stress or the support structure) will be discussed. A second application of modal analysis will be demonstrated: the prediction of the resonances due to passing trains. The response of a bridge to passing trains can be calculated in frequency domain as the multiplication of three spectra, the axle sequence spectrum of the train, the transfer function of the bridge, and the modal force spectrum of a single passing load. A resonance occurs if a maximum of the train spectrum coincides with the maximum of the bridge spectrum. The amplitude at this resonance is strongly influenced by the modal force spectrum which is identical to the frequency or wavenumber spectrum of the corresponding mode shape. Therefore, modal analysis from calculation, impact measurements, wind and train measurements are necessary for the prediction of the resonance occurrence and amplification. Examples of mode shape spectra for single or multi-span bridges with simply supported or continuous spans will be shown, and some relations between mode shapes and resonance amplifications will be concluded. T2 - 11th International Operational Modal Analysis Conference (IOMAC) CY - Rennes, France DA - 20.05.2025 KW - Bridge monitoring KW - Multi-span bridges KW - Damage detection KW - Resonance PY - 2025 AN - OPUS4-63472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rogge, Andreas A1 - Auersch, Lutz T1 - Innovation in track components: heavy sleepers on soft under-sleeper pads N2 - The maintenance of the transport infrastructures and their further development are going to remain focal points for investment and research in Germany in future. According to the latest development forecasts made by both the federal government and Deutsche Bahn, even if rail´s percentage share of the market were to remain unchanged, growth of around 50% would be expected in the next ten years, especially in freight traffic. This growth is necessitating considerable development both in the technical design of the tracks and in the abatement of the noise and vibration caused by railway traffic. PY - 2015 SN - 0013-2845 VL - 2 SP - 9 EP - 13 PB - DVV Media Group, Eurailpress CY - Hamburg AN - OPUS4-34993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir T1 - System and damage identification for cars, floors and roofs, bridges, tracks and foundations by modal analyses, frequency response functions and moving-load responses N2 - The following objects have been analysed by frequency response functions and moving load responses. A simple modal analysis which is based on the transformed and weighted system equations has been tested for an automotive test car and for many floors in many buildings to get some rules for their natural frequency and damping. Moreover, six neighboured equal, weakly coupled, wooden floors in a castle have been measured by ambient and hammer excitation, and a special method to extract the different mode shapes of the closely spaced natural frequencies has been developed and tested. Different foundations, for which the soil-structure interaction is generally important, have been measured and compared with finite-element boundary-element models of varying soil properties. Similarly by FEBEM calculations, damages in railway tracks have been identified from flexibility functions (frequency response functions) and from the moving-load responses to normal train operation. Rail and foot bridges have been measured during train passages and by quasi-static tests with moving vehicles. The repeatability of the inclinometer measurements has been checked for different passages, passage directions, and measurement campaigns at a six-span foot bridge. Two rail bridges at the Hanover-Würzburg high-speed line have been measured and evaluated for integrity and for the train- and speed-dependent bridge resonances. The relation between the multi-axle and the single-axle excitation can be solved in frequency domain by the axle-sequence spectrum of the vehicle or the whole train. The single axle response has been used to identify track and bridge damages in laboratory and in situ. T2 - 10th International Operational Modal Analysis Conference (IOMAC 2024) CY - Naples, Italy DA - 21.05.2024 KW - Weakly coupled floors KW - Bridge passage KW - Track damage KW - Foundation-soil interaction KW - Flexibility function KW - Moving load response PY - 2024 SN - 978-3-031-61420-0 DO - https://doi.org/10.1007/978-3-031-61421-7_19 SN - 2366-2557 SP - 187 EP - 195 PB - Springer Nature Switzerland AG CY - Cham, Schweiz AN - OPUS4-61248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The excitation, propagation, and mitigation of train-induced ground vibrations from the axle impulses on the track N2 - Train-induced vibrations in soft ground usually have a strong low-frequency component. This component has a characteristic spectrum which is related to the axle sequence and the speed of the train. Its attenuation with distance is weaker than the attenuation for higher frequencies, and it always dominates the far-field ground vibration. Narrow-band frequency analyses clearly show that this ground vibration component is due to the static axle loads. Axle box vibrations have a different characteristic where the first out-of-roundness of the wheels is the only remarkable low-frequency component. Therefore, the dynamic axle loads from wheel and track irregularities are not the reason for the strong ground vibration component. The moving static axle loads generate the quasi-static response of the soil at very low frequencies and at very near distances. A part of the original impulse spectrum is scattered when it propagates through an inhomogeneous ballast and soil with a randomly varying stiffness. The axle impulses are smoother for a higher bending stiffness or a lower support stiffness (under sleeper pads, under ballast mats) of the track. This mitigation of the ground vibration will be demonstrated by measurements at three sites in Switzerland as well as the characteristic of the soil and axle-box vibrations. T2 - Railways Conference CY - Prague, Czech Republic DA - 02.09.2024 KW - Soil and vehicle measurements KW - Train passages KW - Ground vibration KW - Excitation mechanisms KW - Mitigation KW - Under sleeper pads KW - Under ballast mat PY - 2024 AN - OPUS4-61226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Song, Jiaojiao T1 - Analysis of intact and damaged (floating) slab tracks by finite-element boundary-element models and by measurements N2 - The damage detection and repair control have become important tasks for slab tracks. Different intact and damaged slab tracks have been investigated theoretically and experimentally for train passages and hammer impacts. The following damages have been considered: The loss of contact between the sleeper and the track slab, between the track slab and the base slab, and between the base slab and the base layer. At first, a slab track with a gap between the track slab and the base layer has been calculated by the combined finite-element boundary-element method which correctly incorporates the behaviour of the infinite soil. The basic results are the track displacements of the rail, the track slab, and the base layer along the track which are caused by a single axle load. These solutions are properly superposed for to get the complete train load. The influence of track and soil parameters and of the track damage has been analysed. For the intact track, the compliance of the soil is dominant whereas the track bending stiffness becomes more important for the damaged track. By comparing the calculated results with the measurements, the length of the gap could be quantified. A slab track with a loose sleeper (without contact to the supporting track slab) was analysed by the transfer function between the displacements and the hammer force (receptance functions) where a resonance appeared in case of the damage. Differences between the different track elements confirmed the detection of the damage. A floating slab track with a thin rubber layer has been investigated for a possible gap between the base slab and the base layer. The behaviour of the intact track has been calculated by a wavenumber-domain method, and the same behaviour has been found in the measurements at several track sections, indicating that there is no damage. Finally, a floating slab track with steel springs and viscous fluid dampers has been measured in the Tongji laboratory. The modes of the floating track slab and the transfer function with corresponding resonances have been calculated and successfully compared with results from wheelset drop tests. T2 - 3rd International Conference of Rail Transportation CY - Shanghai, China DA - 07.08.2024 KW - Slab tracks KW - Damage KW - Vibration measurements KW - Finite-element boundary-element method PY - 2024 AN - OPUS4-61227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Vibrations of multi-span structures like floors, rail and road bridges N2 - Resonances of rail bridges due to the passage of trains have been mainly investigated for sin-gle-span bridges. When multi-span bridges are to be considered, it is of interest if stronger resonance amplifications must be taken into account. Measurements of several multi-span structures have been evaluated for natural frequencies and mode shapes. An integral rail bridge with three different spans shows a separated local resonance of the longest main span and clearly higher natural frequencies of the shorter side spans. A two-span continuous beam on the test area of the Federal Institute of Material Research and Testing showed a regular pattern of natural frequencies where always a pair of frequencies is found with a certain fre-quency ratio. The corresponding mode shapes are the out-of-phase and in-phase combinations of the first, second, third … bending mode. A seven-span road bridge has been monitored for one of the almost equally long spans. Similar mode shapes have been observed for different, clearly separated natural frequencies. Three modal analyses measurement campaigns have been performed on the whole bridge. The combined mode shapes of the seven spans have been clearly identified where different combinations of spans are dominating in the different mode shapes. Equal weakly coupled spans have been analysed for a large wooden floor in a castle. A cluster of natural frequencies has been observed and a special method to extract the mode shapes has been developed and tested. The consequences of multi-span bridges for rail traffic will be discussed. If n simply supported bridge spans have no coupling, n equal modes with amplitude A/n exist and their superposition would yield the same resonance as for a single bridge. Real simply supported bridges have always a weak coupling due to the track or the common piers. Therefore, the natural frequencies differ a little and they cannot be in reso-nance at the same time for the same train passage so that the resonance amplification cannot be as strong as for the single bridge. This rule holds also for the average amplitude of the time history of the bridge passage which is an adequate quantity to judge for the bridge behaviour. The maximum amplitude of the time histories of different bridge points are quite random and could exceed the values of a single bridge. The meaning of such criteria is questioned and fre-quency domain analyses are suggested for a clearer bridge analysis and understanding. T2 - DinEst 2024 Third Conference on Structural Dynamics CY - Seville, Spain DA - 12.09.2024 KW - Rail bridge PY - 2024 SP - 41 EP - 59 PB - Escuela Tecnica Superior de Ingenieria CY - Sevilla AN - OPUS4-61238 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Prediction of ground vibrations from rail tunnels –finite-element, boundary-element and wavenumber calculations N2 - The prediction of ground and building vibrations has been established for surface lines and has now been extended to tunnel lines. The wave propagation in homogeneous or layered soils (the transmission) is calculated by an integration in wavenumber domain. The wave amplitudes at different distances and for different frequencies will be analysed for the following situations. 1. The horizontal propagation from a surface point to a surface point constitutes the basic rules. 2. The horizontal propagation from a source point at depth to a receiver point at depth which is related to a building with a deep basement or on a pile foundation. 3. The propagation from depth to the surface, which is the normal case for free-field measurements, has some different characteristics, for example a weaker attenuation with the horizontal distance from the source, which can be approximated by the full-space solution and the reflection rules for incident waves. The emission from a tunnel structure has been calculated by a finite-element model of the tunnel combined with a boundary-element model of the soil giving the reduction compared to a point-load excitation. The immission has been analysed by finite-element models of tunnel-soil-building systems for examples of research and consultancy work. Measurement results from a high-speed and a metro line confirm some of the established rules. Figure T2 - Int. Conf. RASD, Recent Advance in Structural Dynamics CY - Southampton, GB DA - 01.07.2024 KW - Ground vibration KW - Tunnel line KW - Wave propagation KW - Wavenumber method KW - Building vibration KW - Thin layer method PY - 2024 SP - 1 EP - 12 CY - Southampton AN - OPUS4-61266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Conreaux, Laurence A1 - Said, Samir A1 - Müller, Roger T1 - The excitation, propagation, and mitigation of train-induced ground vibrations from the axle impulses on the track N2 - Train-induced vibrations in soft ground usually have a strong low-frequency component. This component has a characteristic spectrum which is related to the axle sequence and the speed of the train. Its attenuation with distance is weaker than the attenuation for higher frequencies, and it always dominates the far-field ground vibration. Narrow-band frequency analyses clearly show that this ground vibration component is due to the static axle loads. Axle box vibrations have a different characteristic where the first out-of-roundness of the wheels is the only remarkable low-frequency component. Therefore, the dynamic axle loads from wheel and track irregularities are not the reason for the strong ground vibration component. The moving static axle loads generate the quasi-static response of the soil at very low frequencies and at very near distances. A part of the original impulse spectrum is scattered when it propagates through an inhomogeneous ballast and soil with a randomly varying stiffness. The axle impulses are smoother for a higher bending stiffness or a lower support stiffness (under sleeper pads, under ballast mats) of the track. This mitigation of the ground vibration will be demonstrated by measurements at three sites in Switzerland as well as the characteristic of the soil and axle-box vibrations. T2 - Sixth International Conference on Railway Technology: Research, Development and Maintenance CY - Prague, Czech Republic DA - 01.09.2024 KW - Soil and vehicle measurements KW - Train passages KW - Ground vibration KW - Excitation mechanisms KW - Mitigation KW - Under sleeper pads KW - Under ballast mat PY - 2024 DO - https://doi.org/10.4203/ccc.7.13.2 SN - 2753-3239 VL - 7 SP - 1 EP - 13 PB - Civil-Comp Press CY - Edinburgh, United Kingdom AN - OPUS4-61240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - System and damage identification for cars, floors and roofs, bridges, tracks and foundations by modal analyses, frequency response functions and moving load responses N2 - The following objects have been analysed by frequency response functions and moving load responses. A simple modal analysis which is based on the transformed and weighted system equations has been tested for an automotive test car and for many floors in many buildings to get some rules for their natural frequency and damping. Moreover, six neighboured equal, weakly coupled, wooden floors in a castle have been measured by ambient and hammer excitation, and a special method to extract the different mode shapes of the closely spaced natural frequencies has been developed and tested. Different foundations, for which the soil-structure interaction is generally important, have been measured and compared with finite-element boundary-element models of varying soil properties. Similarly by FEBEM calculations, damages in railway tracks have been identified from flexibility functions (frequency response functions) and from the moving-load responses to normal train operation. Rail and foot bridges have been measured during train passages and by quasi-static tests with moving vehicles. The repeatability of the inclinometer measurements has been checked for different passages, passage directions, and measurement campaigns at a six-span foot bridge. Two rail bridges at the Hanover-Würzburg high-speed line have been measured and evaluated for integrity and for the train- and speed-dependent bridge resonances. The relation between the multi-axle and the single-axle excitation can be solved in frequency domain by the axle-sequence spectrum of the vehicle or the whole train. The single axle response has been used to identify track and bridge damages in laboratory and in situ. T2 - 10th International Operational Modal Analysis Conference (IOMAC 2024) CY - Naples, Italy DA - 21.05.2024 KW - Weakly coupled floors KW - Bridge passage KW - Track damage KW - Foundation-soil interaction KW - Flexibility function KW - Moving load response PY - 2024 AN - OPUS4-61233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -