TY - JOUR A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Fontana, Patrick A1 - Müller, Urs A1 - Ziegert, C. T1 - Charakterisierung und Modellierung der mechanischen Eigenschaften von Lehmsteinmauerwerk / Mechanical characterization and modelling of earth block masonry JF - Das Mauerwerk N2 - Das Wissen über die Materialeigenschaften und die Versagensmechanismen bei Lehmbaustoffen ist begrenzt und lückenhaft. Im Rahmen des EU-Projekts NIKER (www.niker.eu) wurden deshalb die mechanischen Eigenschaften von Bauteilen aus Lehm unter statischer Druck- und Schubbeanspruchung bestimmt. Ziel der Untersuchungen war es, grundlegende Daten zum Verformungs- und Versagensverhalten von Lehmbauteilen zu erhalten und dieses mit einem numerischen Modell zu beschreiben. Die Versuchsergebnisse belegten das spröde Verhalten von Lehmsteinmauerwerk bei uniaxialer Druckbelastung und zeigten, dass das Versagen von Lehmsteinmauerwerk infolge Schubbelastung nach Erstrissbildung in Mörtelfugen und Lehmsteinen durch Gleiten der Lehmsteine entlang der Mörtelfugen erfolgt. Die numerische Makromodellierung erbrachte zwar befriedigende Resultate hinsichtlich des Spannungs-Dehnungs-Verhaltens, jedoch konnte bei der simulierten Rissbildung keine Übereinstimmung mit den in den Versuchen beobachteten Rissbildern erzielt werden. Bei Lehmsteinmauerwerk ist also eine wesentlich aufwendigere Mikromodellierung notwendig, um das Versagensverhalten korrekt beschreiben zu können.-------------------------------------------------------------------------------------------------------------- Knowledge of the material properties and failure mechanisms of earthen materials is limited and scattered. Within the framework of the NIKER project (www.niker.eu) funded by EC, the mechanical properties of earthen material elements were therefore determined under static compression and shear loads. The aim was to obtain fundamental data on deformation behaviour and failure mechanisms of earthen material structural elements and to describe them by means of a numerical model. The test results confirmed the brittle behaviour of earth block masonry under monoaxial compressive load and showed that the failure of earth block masonry under shear load occurs by sliding of the earth blocks along the mortar joints after initial cracking in mortar joints and earth block. Numerical macro modelling showed satisfying results with regard to stress-strain behaviour, but the simulated crack pattern was not consistent with experimental observations. In the case of earth block masonry, it is thus necessary to use micro modelling approaches in order to correctly predict the failure process at local level. KW - Lehmstein Mauerwerk KW - Druckversuche KW - Schubversuche KW - F.E.M. Modellierung PY - 2012 DO - https://doi.org/10.1002/dama.201200555 SN - 1432-3427 SN - 1437-1022 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 16 IS - 6 SP - 279 EP - 292 PB - Ernst CY - Berlin AN - OPUS4-27589 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferraioli, M. A1 - Miccoli, Lorenzo A1 - Abruzzese, D. A1 - Mandara, A. T1 - Dynamic characterisation and seismic assessment of medieval masonry towers JF - Natural Hazards N2 - The paper investigates the dynamic characterisation, the numerical model tuning and the seismic risk assessment of two monumental masonry towers located in Italy: the Capua Cathedral bell tower and the Aversa Cathedral bell tower. Full-scale ambient vibration tests under environmental loads are performed. The modal identification is carried out using techniques of modal extraction in the frequency domain. The refined 3D finite element model (FEM) is calibrated using the in situ investigation survey. The FEM tuning is carried out by varying the mechanical parameters and accounting for the restraint offered by the neighbouring buildings and the role of soil–structure interaction. The assessment of the seismic performance of the bell towers is carried out through a nonlinear static procedure based on the multi-modal pushover analysis and the capacity spectrum method. Through the discussion of the case studies, the paper shows that the modal identification is a reliable technique that can be used in situ for assessing the dynamic behaviour of monumental buildings. By utilising the tuned FEM of the towers, the theoretical fundamental frequencies are determined, which coincide with the previously determined experimental frequencies. The results from seismic performance assessment through a pushover analysis confirm that the masonry towers in this study are particularly vulnerable to strong damage even when subjected to seismic events of moderate intensity. KW - masonry towers KW - ambient vibration tests KW - dynamic characterisation KW - seismic assessment PY - 2016 DO - https://doi.org/10.1007/s11069-016-2519-2 SN - 1573-0840 SN - 0921-030X VL - 86 SP - Suppl. 2, S489 EP - S515 PB - Springer AN - OPUS4-37187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Drougkas, T. A1 - Müller, U. T1 - In-plane behaviour of rammed earth under cyclic loading: experimental testing and finite element modelling JF - Engineering Structures N2 - The purpose of this paper is to numerically simulate the in-plane behaviour of rammed earth walls under cyclic shear-compression tests. The experimental testing allowed obtaining the maximum horizontal loads, the displacement capacity and the level of non-linear behaviour of the respective loaddisplacement relationships as well as the failure modes. The calibration of the numerical model (finite element method) was carried out based on the experimental results. Within this framework, a micromodelling approach was considered. The behaviour of the rammed earth material was simulated using a total strain rotating crack model. A Mohr-Coulomb failure criterion was used to reproduce the behaviour of the interfaces between the layers. Although the numerical results achieved a satisfactory agreement with the experimental results a sensitivity analysis of the parameters involved was performed. The sensitivity analysis aimed at determining which parameters of the model have a significant impact in the model’s results. As expected the sensitivity analysis pointed out that the sliding failure occurrence is mainly influenced by two parameters of the interface elements: the interface tensile strength fit and the friction angle u. Moreover the cohesion c and the layers thickness showed a limited effect on the shear behaviour. It should be noted that the results mentioned above are related to the cases where a significant level of vertical compressive stress r is employed. KW - rammed earth KW - in-plane loads KW - shear behaviour KW - cyclic shear-compression tests KW - finite element modelling KW - pseudo-dynamic tests PY - 2016 DO - https://doi.org/10.1016/j.engstruct.2016.07.010 SN - 0141-0296 SN - 1873-7323 VL - 125 SP - 144 EP - 152 PB - Elsevier Ltd. AN - OPUS4-37165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, U. A1 - Miccoli, Lorenzo A1 - Fontana, Patrick T1 - Development of a lime based grout for crack repair in earthen constructions JF - Construction and Building Materials N2 - The study presents the results from the development of a grouting material based on hydrated lime with addition of pozzolana, which is referred to as hydraulic lime, suitable for the repair of cracks in a variety of earthen building techniques. The goal was to develop a material also compatible with earthen structures exposed to dynamic loads. The grouting mortar was designed to be adaptable in strength properties and at the same time to have sufficient robustness for preparation and use on the construction site. Results showed a satisfactory performance of the grout concerning fresh and hardened mortar properties as well as injectability. KW - Earthen construction KW - Lime based grout KW - Cracks grouting KW - Rheology KW - Strength KW - Adhesion PY - 2016 DO - https://doi.org/10.1016/j.conbuildmat.2016.02.030 SN - 0950-0618 VL - 110 SP - 323 EP - 332 PB - Elsevier AN - OPUS4-37064 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Oliveira, D.V. A1 - Silva, R.A. A1 - Müller, U. A1 - Schueremans, L. T1 - Static behaviour of rammed earth: experimental testing and finite element modelling JF - Materials and structures N2 - The paper presents an experimental program aiming at assessing the mechanical performance of rammed earth walls, namely under compression and shear loading. Axial compression and diagonal compression tests were carried out for this purpose, which allowed determining important mechanical parameters, such as compressive strength, Young's modulus, Poisson's ratio, shear strength and shear modulus. Furthermore, it allowed assessing the level of non-linear behaviour of the respective stress–strain relationships as well as the failure modes. The experimental results were then used in the calibration of numerical models (finite element method) for simulating the non-linear behaviour of rammed earth under shear loading. Both macro- and micro modelling approaches were considered for this purpose. The total strain rotating crack model was used to simulate the behaviour of the rammed earth material, while the Mohr–Coulomb failure criterion was used to simulate the behaviour of interfaces between layers. In general, the numerical models achieved good agreement with the experimental results, but uncertainties related to the definition of the input parameters required to perform a sensitivity analysis. The compressive strength, the Poisson's ratio, the tensile strength and the tensile fracture energy revealed to be the most important parameters in the analyses. KW - Rammed earth KW - Compression behaviour KW - Shear behaviour KW - Finite element analysis PY - 2015 UR - http://link.springer.com/article/10.1617/s11527-014-0411-7/fulltext.html DO - https://doi.org/10.1617/s11527-014-0411-7 SN - 1359-5997 SN - 1871-6873 VL - 48 IS - 10 SP - 3443 EP - 3456 PB - Springer CY - Dordrecht AN - OPUS4-31329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Müller, U. A1 - Fontana, Patrick T1 - Mechanical behaviour of earthen materials: A comparison between earth block masonry, rammed earth and cob JF - Construction and building materials N2 - Earth represents one of the oldest construction materials, which is still utilised both in developed and in developing countries. In this paper a comparison of the mechanical performance of structural elements built in three basic techniques, earth block (adobe) masonry, rammed earth and cob, is presented. In order to gain better knowledge on the structural behaviour under static loads an extensive compression and diagonal compression (shear) test campaign was performed. First compression results showed brittle mechanical behaviour in the case of earth block masonry and rammed earth elements, whereas cob exhibited a very different stress–strain pattern: cob can deform beyond the elastic range with a gradual drop in capacity. Despite its low compressive strength, cob thus presents a relatively good performance within the earthen material range as far as shear behaviour is concerned. The data here reported represents a base for a further investigation on the dynamic behaviour of the three materials considered. The study was carried out within the framework of the project NIKER funded by the European Commission dealing with improving immovable Cultural Heritage assets against the risk of earthquakes. KW - Earthen materials KW - Compression test KW - Diagonal compression test KW - Initial shear strength PY - 2014 DO - https://doi.org/10.1016/j.conbuildmat.2014.03.009 SN - 0950-0618 VL - 61 SP - 327 EP - 339 PB - Elsevier Science CY - Amsterdam AN - OPUS4-30550 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Garofano, A. A1 - Fontana, Patrick A1 - Müller, U. T1 - Experimental testing and finite element modelling of earth block masonry JF - Engineering structures N2 - The current paper focuses on the determination of reliable numerical models of earth block masonry wallettes under different loading conditions. Uniaxial compression and diagonal compression tests were performed. Experimental behaviour was modelled with a non-linear model able to describe the cracking behaviour. The simplified approach based on macro-modelling shows a satisfactory accuracy and low computational costs. The results reproducing the uniaxial compression are in good correspondence with the post-elastic behaviour observed in the experimental campaign. The micro-modelling approach adopted to reproduce the shear behaviour, even with high computational cost, represents a suitable tool to predict the masonry collapse mechanism. KW - Earth block masonry KW - Uniaxial compression test KW - Diagonal compression test KW - Numerical modelling KW - Macro-modelling approach KW - Micro-modelling approach PY - 2015 DO - https://doi.org/10.1016/j.engstruct.2015.09.020 SN - 0141-0296 VL - 104 SP - 80 EP - 94 PB - Elsevier CY - Oxford AN - OPUS4-34553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Paganoni, S. A1 - Fontana, Patrick A1 - D'Ayala, D. T1 - Pull-out strength of anchor pins for brickwork masonry and earth block masonry / Auszugsfestigkeit von Verpressankern für Ziegel- und Lehmsteinmauerwerk JF - Das Mauerwerk N2 - In this paper results of the experimental testing performed on brick masonry and earth block masonry are presented. The paper outlines the development of the testing procedures for two different types of anchors. For this purpose, two experimental campaigns of pull-out tests on masonry corner connections strengthened by metallic rod grouted were carried out. Experimental results proved that the implemented testing procedures are suitable to determine the most recurring failure modes of the anchor pins. Moreover, a procedure is proposed to estimate the capacity of grouted anchor pins based on experimental studies. N2 - Mit diesem Beitrag soll die experimentelle Beurteilung von Verpressankern für Mauerwerk vorgestellt werden. Es wurden zwei Versuchsserien mit Ankerauszugsversuchen an Mauerwerksecken aus Ziegel- und Lehmsteinmauerwerk durchgeführt. Die Versuchsergebnisse haben gezeigt, dass die gewählten Versuchsabläufe geeignet sind, die am häufigsten wiederkehrenden Versagensarten der Verpressanker zu bestimmen. Darüber hinaus wird eine Vorgehensweise vorgeschlagen, die es ermöglicht, die Traglast von Verpressankern auf Basis experimenteller Untersuchungen abzuschätzen. KW - Brickwork masonry KW - Earth block masonry KW - Anchor pins KW - Bond strength KW - Pull-out test PY - 2015 DO - https://doi.org/10.1002/dama.201500669 SN - 1432-3427 SN - 1437-1022 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 19 IS - 5 SP - 383 EP - 393 PB - Ernst CY - Berlin AN - OPUS4-34634 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Silva, N. A1 - Klinge, A. A1 - Cederqvist, C. A1 - Kreft, O. A1 - Qvaeschning, D. A1 - Sjöström, C. T1 - Composite UHPC-AAC/CLC facade elements with modified interior plaster for new buildings and refurbishment. Materials and production technology JF - Journal of Facade Design and Engineering N2 - The awareness of the environmental impact of the building sector is increasing. Steel reinforced concrete is the most commonly used construction material, though with a high-embodied energy and carbon footprint. Large environmental gains may arise if an alternative to steel reinforced concrete is developed. In this context, ultra-high performance concrete (UHPC) materials are shown to be promising alternatives with advantages such as lower embodied energy and reduced environmental impact. Predictions suggest that UHPC composite elements for building envelopes could have other benefits such as an increased service life, optimised use of building area due to thinner elements and minimised maintenance due to the absence of reinforcement or use of non-corrosive reinforcing materials such as carbon fibres. In the framework of the H-HOUSE project funded by the European Commission, composite elements are developed. The aim is to create facade panels combining an autoclaved aerated concrete or cellular lightweight concrete insulation layer with an external UHPC supporting layer. To enhance occupant comfort and health, hygroscopic materials that are capable to buffer indoor air humidity shall be applied to the inside of such elements. Indoor air humidity levels are expected to be more stable, which shall subsequently improve the indoor climate and minimise potential decay to the construction. KW - Composite panels KW - Ultra-high performance concrete (UHPC) KW - Autoclaved aerated concrete (AAC) KW - Cellular lightweight concrete (CLC) KW - Aerogel KW - Modified earth plaster PY - 2015 DO - https://doi.org/10.3233/FDE-150029 SN - 2214-302X VL - 3 IS - 1 SP - 91 EP - 102 PB - IOS Press AN - OPUS4-33605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Philipp A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Ziegert, C. T1 - Development of partial safety factors for earth block masonry JF - Materials and Structures N2 - The main aim of the research was the development of a first valid database for material parameters of earth block masonry (EBM) with particular regard to statistical characteristics. A solid database is needed for the determination of the materials partial safety factor. Therefore, compressive strength tests were carried out with two types of earth blocks and two types of prefabricated earth mortar. The evaluation has shown that the mean variation of the compressive strength was remarkably less than expected, which indicates high quality standards of the components earth block and mortar with regard to industrial production. Using the reliability method, a partial safety factor for EBM subjected to compression was determined on the basis of these test results. The findings have shown that a common calculation method for EBM based on partial safety factors following the valid masonry construction standard is feasible. KW - Partial safety factor KW - Earth block masonry (EBM) KW - Reliability KW - Compressive strength PY - 2017 DO - https://doi.org/10.1617/s11527-016-0902-9 SN - 1871-6873 SN - 1359-5997 VL - 50 IS - 1 SP - 1 EP - 14 PB - Springer AN - OPUS4-38937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferraioli, M. A1 - Miccoli, Lorenzo A1 - Abruzzese, D. T1 - Dynamic characterisation of historic bell-tower using a sensitivity-based technique for model tuning JF - Journal of Civil Structural Health Monitoring N2 - The most relevant results of the vibration-based investigations performed on a historic masonry tower in Italy namely the Santa Maria a Vico bell-tower is here presented. The first part of the study involves preliminary full-scale ambient vibration measurements in operational conditions and dynamics-based finite element (FE) modelling. At first, a manual tuning of the uncertain parameters of the model was carried out to adjust material properties, soil-structure interaction and constraining effect of the neighbouring structures. Then, based on the sensitivity analysis, only the most sensitive parameters were chosen as updating parameters. Finally, a model updating technique based on a sensitivity-based method was used to minimise the error between experimental vibration data and numerical response values. To this aim, a residual vector defined as the weighted difference between the measured quantities and calculated quantities was used. The uncertain structural parameters of the FE model were identified by minimising a robust penalty function. The calibrated model was used as an important tool for the seismic assessment of the structure using pushover analysis. Since the assumed value of the masonry compressive strength is the most sensitive parameter of non-linear behaviour, a sensitivity analysis was performed considering reference values in the range of interest. The seismic safety corresponding to increasing levels of the seismic hazard was finally investigated. KW - Masonry tower KW - Ambient vibration measurements KW - Structural identification KW - Model tuning PY - 2018 DO - https://doi.org/10.1007/s13349-018-0272-9 SN - 2190-5479 SP - 1 EP - 17 PB - Springer-Verlag GmbH CY - Germany AN - OPUS4-44161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fontana, Patrick A1 - Miccoli, Lorenzo A1 - Grünberg, U. T1 - Experimental investigations on the initial shear strength of masonry with earth mortars JF - International Journal of Masonry Research and Innovation N2 - In this paper, a comparative study on the initial shear strength of masonry with earth mortars is presented. Triplet tests were carried out to characterise the shear bond strength of five different types of earth mortar, three purely mineral and two with vegetable additives (wood and straw chaff), using calcium silicate blocks. In spite of their lower bulk densities, mortars with chaffs reached a value of compressive strength comparable to the values shown by the purely mineral mortars. The characteristic initial shear strengths of all the tested earth mortars were between two and five times higher than the minimum values for initial shear strengths required by standards. To assess the influence of blocks pre-wetting, a comparison between calcium silicate blocks and earth blocks was performed to evaluate the results obtained from the standard test procedure compared to the more common practice of using earth mortars in combination with earthen blocks. KW - Earth mortar KW - Sand-lime block KW - Earth block KW - Initial shear strength KW - Shear bond test KW - Masonry KW - Triplet test PY - 2018 DO - https://doi.org/10.1504/IJMRI.2018.10009831 SN - 2056-9459 SN - 2056-9467 VL - 3 IS - 1 SP - 34 EP - 49 PB - Inderscience Enterprises Ltd. CY - Olney, Bucks AN - OPUS4-43692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Müller, U. A1 - Pospisil, S. T1 - Rammed earth walls strengthened with polyester fabric strips: Experimental analysis under in-plane cyclic loading JF - Construction and Building Materials N2 - This study analyses the mechanical behaviour under pseudo-dynamic loading of structural elements built in rammed earth and strengthened with polyester fabric strips. This strengthening technique was developed to exploit the strength potential of rammed earth and to solve its lack of tensile strength. For this reason, in-plane cyclic tests were carried out to investigate the shear behaviour of unstrengthened and strengthened walls. The strengthening technique requires low-tech equipment and workmanship, uses readily available, not expensive and industrially standardised materials. The experimental results were analysed in terms of stiffness degradation, energy dissipation capacity and equivalent viscous damping. Although the unstrengthened and strengthened walls confirmed a limited ductile behaviour, the findings confirm that the strengthening contributes to limit the spread of the diagonal cracks and provide an increase of strength in terms of horizontal load and displacement capacity. KW - Rammed earth KW - Pseudo-dynamic loads KW - Shear-compression tests KW - Strengthening KW - Polyester fabric strips PY - 2017 DO - https://doi.org/10.1016/j.conbuildmat.2017.05.115 IS - 149 SP - 29 EP - 36 PB - Elsevier Ltd. AN - OPUS4-40497 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Gerrard, C. A1 - Perrone, C. A1 - Gardei, André A1 - Ziegert, C. T1 - A collaborative engineering and archaeology project to investigate decay in historic rammed earth structures: The case of the Medieval preceptory in Ambel JF - International Journal of Architectural Heritage N2 - This study assesses the structural vulnerability of part of a later medieval earthen building at Ambel (near Zaragoza, Spain), once a preceptory or monastic house belonging to the Military Orders. An inspection of its morphology and materials coupled with the results of an extensive campaign of static monitoring reveals marked structural inhomogeneities, the product of more than a thousand years of construction, failure, and repair from the 10th century to the present day. Building materials are inappropriately juxtaposed, there are discontinuities between construction phases and fundamental concerns remain over the long-term stability of the structure. The current condition of the structure is mainly influenced by structural discontinuities introduced at the time of construction, the unintended consequences of repair and modification and the material decay that has affected the base of the rammed earth walls. The overall findings of the static monitoring show that there is no related damage, variations in crack widths are related to the building seasonal cycle. While static analysis is an essential prerequisite before a suitable maintenance program can be fully defined, this study argues that no evaluation of the structural behavior of any historic building can afford to ignore its archaeological “biography” of modification and repair. KW - Archaeology KW - Historical earthen building KW - Materials characterization KW - Rammed earth KW - Static monitoring PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-396274 DO - https://doi.org/10.1080/15583058.2016.1277283 VL - 11 IS - 5 SP - 636 EP - 655 PB - Taylor & Francis Group AN - OPUS4-39627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Silva, R. A. A1 - Oliveira, D. V. A1 - Müller, U. T1 - Static behavior of cob: Experimental testing and finite-element modeling JF - Journal of Materials in Civil Engineering N2 - The aim of this paper is to implement a numerical model to reproduce the nonlinear behavior of cob walls under shear loading. Axial compression, pull-off, and diagonal compression tests were carried out to derive the mechanical parameters. In addition, the stressstrain relationships, the nonlinear behavior, and the failure modes were defined. The experimental results were then used to calibrate a finiteelement model. The material behavior was simulated through a macromodeling approach adopting the total strain rotating crack model. A sensitivity analysis was conducted to assess the effects of varying the parameters with higher uncertainty on the structural behavior. The numerical model achieved good correspondence with the experimental results in terms of simulation of the shear stress–shear strain relationship and of damage pattern. KW - Cob KW - Compression behavior KW - Shear behavior KW - Digital image correlation KW - Finite-element method PY - 2019 DO - https://doi.org/10.1061/(ASCE)MT.1943-5533.0002638 SN - 0899-1561 SN - 1943-5533 VL - 31 IS - 4 SP - 04019021-1 EP - 04019021-13 PB - ASCE American Society of Civil Engineers AN - OPUS4-47316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -