TY - CONF A1 - Bäßler, Ralph A1 - Keserović, A. A1 - Sobetzki, J. A1 - Sarmiento-Klapper, H. A1 - Boduch, A. A1 - Aristia, G. A1 - Faes, W. A1 - Stoljarova, A. A1 - Zimmer, S. T1 - Metallene Werkstoffe in Geothermieanlagen - nicht nur aus Sicht der Korrosion N2 - Um Konstrukteuren und Nutzern geothermischer Anlagen grundlegende Informationen über die Korrosionsbeständigkeit zur Verfügung zu stellen, wurden verschiedene metallene Werkstoffe, darunter nichtrostende Duplex- und austenitische Stähle sowie eine Nickellegierung, in künstlichen Geothermalwässern, die die Bedingungen an verschiedenen Standorten mit geothermischem Potenzial simulieren, mit Hilfe von elektrochemischen und Langzeittests hinsichtlich ihrer Eignung bewertet. In hochsalinaren Umgebungen erwies sich Spaltkorrosion als der entscheidende Mechanismus. Die Nickellegierung zeigt eine ausgezeichnete Beständigkeit gegenüber Lochkorrosion. Abgesehen von ihren hohen Kosten eignet sie sich sehr gut für den Bau von Geothermieanlagen mit stark salzhaltigen Fluiden. Rostfreie Stähle und Duplexstähle weisen eine begrenzte Korrosionsbeständigkeit gegen Loch- und Spaltkorrosion auf. Daher sind sie für stark salzhaltige Fluide nicht geeignet. Der Superaustenit zeigt ein temperaturabhängiges Verhalten. In nichtsalinaren Umgebungen könnten niedriglegierte Stähle (neben den höherlegierten Werkstoffen) als Konstruktionsmaterial für Geothermieanlagen eingesetzt werden, sofern eine ausreichende Wandstärke des Materials berücksichtigt wird. Neben Korrosionsaspekten erwies sich auch die Ausfällung von Fluidbestandteilen als interessantes Thema. Beim Betrieb der Forschungsanlage in Groß Schönebeck wurden Kupfer- und Bleieffekte im Bohrloch festgestellt. Die auftretenden Mechanismen und Maßnahmen zur Verhinderung von Ausfällungen und Abscheidungen wurden ebenso untersucht, wie deren mögliche Einflüsse auf die Korrosionsbeständigkeit metallener Werkstoffe für Anlagenkomponenten. Der Beitrag beschreibt die Wechselwirkungen zwischen Geothermalwässern und Ausrüstungskomponenten. T2 - 57. Kraftwerktechnisches Kolloquium CY - Dresden, Germany DA - 07.10.2025 KW - Örtliche Korrosion KW - Edelstahl KW - Ni-Legierungen KW - Geothermie KW - Abscheidung PY - 2025 SN - 978-3-00-082651-1 SN - 978-3-00-082652-8 SP - 551 EP - 568 PB - IKS-Verlag CY - Freiberg AN - OPUS4-64320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Keserovic, A. A1 - Bäßler, Ralph T1 - Material evaluation for application in geothermal systems in Indonesia N2 - Material selection is one of the major aspects when it comes to designing a geothermal power plant due to the highly concentrated solutions of corrosive salts at high temperatures and pressures present in geothermal systems. The main goal of the present study was to evaluate the corrosion behavior of three different steel grades (low alloy steel UNS G41300, stainless steel UNS S31603 and high-alloyed stainless steel UNS N08031) by means of exposure and electrochemical tests in static conditions at 100 °C (100 kPa) and 175 °C (800 kPa). The research was carried out in a synthetic geothermal fluid (1,500 mg/L chlorides, 20 mg/L sulphates, pH 4), simulating the conditions present at the geothermal field Sibayak, North Sumatra (Indonesia). Different test setups were performed in order to investigate the most common corrosion types present in geothermal systems; uniform, pitting and crevice corrosion. According to the obtained results at 100 °C, stainless steel could represent an option to be used in the designed geothermal application due to its excellent performance in terms of corrosion resistance, compared to alloy UNS G41300, and lower cost, compared to alloy UNS N08031. However, for 175 °C, a higher alloyed material should be evaluated or appropriate material protection methods should be considered, since none of the investigated materials provided absolutely satisfying results. T2 - NACE International Corrosion Conference 2013 CY - Orlando, FL, USA DA - 17.03.2013 KW - Geothermal KW - Corrosion KW - Low alloy steel KW - Stainless steel KW - Electrochemistry PY - 2013 SN - 978-1-627-48145-8 SP - 1 EP - 10 (Paper 2269) PB - Curran CY - Red Hook, NY AN - OPUS4-29401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Keserovic, A. A1 - Bäßler, Ralph A1 - Kamah, Y. T1 - Suitability of alloyed steels in highly acidic geothermal environments N2 - This study aims to evaluate which of the materials currently available on the market could overcome the Problem of corrosion and withstand highly aggressive conditions in the exploitation of geothermal resources in volcanic environments. Our investigations were triggered by the conditions on Lahendong geothermal field (North Sulawesi, Indonesia): well LHD-23 presents one of the greatest challenges due to its capacity of producing > 20 MWe of energy from a single well and in the same time having very low pH (2-3) and relatively high Chloride (1,500 mg/L) and sulphate (1,600 mg/L) concentration. Three different Steel grades (low-alloyed Steel UNS G41300, stainless Steel UNS S31603 and high-alloyed stainless Steel UNS N08031) were selected, and their corrosion behavior was evaluated by means of short-term electrochemical methods (potentiodynamic polarization) and long-term exposure tests (up to 6 months). The research was carried out in the laboratory under stagnant conditions in the artificial LHD-23 geothermal brine (1,500 mg/L Chlorides, 1,600 mg/L sulphates, pH 2) at 100 °C (100 kPa) and 175 °C (900 kPa), simulating the conditions present at the site. T2 - Corrosion 2014 CY - San Antonio, TX, USA DA - 09.03.2014 KW - Geothermal KW - Corrosion KW - Carbon steel KW - Stainless steel KW - Electrochemistry PY - 2014 SP - Paper 4031, 1 EP - 14 AN - OPUS4-30542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -