TY - JOUR A1 - Qian, H. A1 - Kalinka, Gerhard A1 - Chan, K.L.A. A1 - Kazarian, S.G. A1 - Greenhalgh, E.S. A1 - Bismarck, A. A1 - Shaffer, M.S.P. T1 - Mapping local microstructure and mechanical performance around carbon nanotube grafted silica fibres: Methodologies for hierarchical composites N2 - The introduction of carbon nanotubes (CNTs) modifies bulk polymer properties, depending on intrinsic quality, dispersion, alignment, interfacial chemistry and mechanical properties of the nanofiller. These effects can be exploited to enhance the matrices of conventional microscale fibre-reinforced polymer composites, by using primary reinforcing fibres grafted with CNTs. This paper presents a methodology that combines atomic force microscopy, polarised Raman spectroscopy, and nanoindentation techniques, to study the distribution, alignment and orientation of CNTs in the vicinity of epoxy-embedded micrometre-scale silica fibres, as well as, the resulting local mechanical properties of the matrix. Raman maps of key features in the CNT spectra clearly show the CNT distribution and orientation, including a ‘parted’ morphology associated with long grafted CNTs. The hardness and indentation modulus of the epoxy matrix were improved locally by 28% and 24%, respectively, due to the reinforcing effects of CNTs. Moreover, a slower stress relaxation was observed in the epoxy region containing CNTs, which may be due to restricted molecular mobility of the matrix. The proposed methodology is likely to be relevant to further studies of nanocomposites and hierarchical composites. KW - Nanotubes KW - Silica fibres KW - Nano indentation KW - Mapping PY - 2011 DO - https://doi.org/10.1039/c1nr10497g SN - 2040-3364 SN - 2040-3372 VL - 3 IS - 11 SP - 4759 EP - 4767 PB - RSC Publ. CY - Cambridge AN - OPUS4-34718 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Mechanische Eigenschaften des Faser/Matrix Interfaces in Verbundwerkstoffen T2 - ILA 2010-Berlin Airshow, Konferenz: Composites in der Luft- und Raumfahrt CY - Berlin, Germany DA - 2010-06-08 PY - 2010 AN - OPUS4-21415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - mechanical properties of the fibre/matrix interface region of composite materials T2 - Eingeladener Vortrag Katholike Universitaet Leuven CY - Leuven, Belgium DA - 2010-07-01 PY - 2010 AN - OPUS4-23078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Bestimmung zeitabhängiger lokaler Eigenschaften von Polymeren mit der Nano-Indentationstechnik T2 - 15. Nationales SAMPE Symposium, BAM CY - Berlin, Germany DA - 2009-02-18 PY - 2009 AN - OPUS4-19013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Local mechanical relaxation time spectroscopy with using the nano indentation technique T2 - THERMOSETS 2009 CY - Berlin, Germany DA - 2009-10-01 PY - 2009 AN - OPUS4-20123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Kalinka, Gerhard T1 - Local failure processes in fiber reinforced polymers N2 - The breakage of a fiber and its effect on the strain energy is studied in a model composite, this is, a single fiber embedded in a dogbone specimen. The fracture process is recorded by an acoustic emission device, the crack patterns are monitored under a microscope. A finite element analysis is performed in order to estimate the energy released by different failure scenarios. The abilities and limitations of the acoustic emission analysis in characterizing different failure types in fiber reinforced composites are evaluated. T2 - ICCM17 - 17th International conference on composite materials CY - Edinburgh, UK DA - 2009-07-27 KW - Fiber KW - Interface KW - Composite material KW - Failure KW - Acoustic emission KW - Fracture mechanics KW - Energy release rate KW - Finite element analysis PY - 2009 IS - D7:8 SP - 1 EP - 10 CY - Edinburgh, UK AN - OPUS4-21295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Single Fiber Pull-out Test T2 - 4th International CFK-Valley Stade Convention CY - Stade, Germany DA - 2010-06-15 PY - 2010 AN - OPUS4-23289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pommet, M. A1 - Juntaro, J. A1 - Heng, J.Y.Y. A1 - Mantalaris, A. A1 - Lee, A.F. A1 - Wilson, K. A1 - Kalinka, Gerhard A1 - Shaffer, M.S.P. A1 - Bismarck, A. T1 - Surface modification of natural fibers using bacteria: depositing bacterial cellulose onto natural fibers to create hierarchical fiber reinforced nanocomposites N2 - Triggered biodegradable composites made entirely from renewable resources are urgently sought after to improve material recyclability or be able to divert materials from waste streams. Many biobased polymers and natural fibers usually display poor interfacial adhesion when combined in a composite material. Here we propose a way to modify the surfaces of natural fibers by utilizing bacteria (Acetobacter xylinum) to deposit nanosized bacterial cellulose around natural fibers, which enhances their adhesion to renewable polymers. This paper describes the process of modifying large quantities of natural fibers with bacterial cellulose through their use as substrates for bacteria during fermentation. The modified fibers were characterized by scanning electron microscopy, single fiber tensile tests, X-ray photoelectron spectroscopy, and inverse gas chromatography to determine their surface and mechanical properties. The practical adhesion between the modified fibers and the renewable polymers cellulose acetate butyrate and poly(l-lactic acid) was quantified using the single fiber pullout test. KW - Composires KW - Bacteria KW - Surface KW - Cellulose natural fibers PY - 2008 DO - https://doi.org/10.1021/bm800169g SN - 1525-7797 VL - 9 IS - 6 SP - 1643 EP - 1651 PB - ACS Publ. CY - Washington, DC, USA AN - OPUS4-23162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Juntaro, J. A1 - Pommet, M. A1 - Kalinka, Gerhard A1 - Mantalaris, A. A1 - Shaffer, M.S.P. A1 - Bismarck, A. T1 - Creating Hierarchical Structures in Renewable Composites by Attaching Bacterial Cellulose onto Sisal Fibers KW - Nanotubes KW - Cellulose KW - Polymer KW - Interface KW - Hierarchical Structures PY - 2008 DO - https://doi.org/10.1002/adma.200703176 SN - 0935-9648 SN - 1521-4095 VL - 20 IS - 16 SP - 3122 EP - 3126 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-18258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tran, M.Q. A1 - Ho, K.K.C. A1 - Kalinka, Gerhard A1 - Shaffer, M.S.P. A1 - Bismarck, A. T1 - Carbon fibre reinforced poly(vinylidene fluoride): Impact of matrix modification on fibre/polymer adhesion N2 - The quality of interfacial interaction is dictated by the surface chemistry of the carbon fibres and the composition of the matrix. The composition of poly(vinylidene fluoride) (PVDF) was modified by the addition of maleic anhydride grafted PVDF. The surface properties of the various matrix formulations were characterised by contact angle and electrokinetic measurements. Carbon fibres were modified by industrial electrochemical oxidation and oxidation in nitric acid, or the use of a traditional epoxy-sizing of industrially oxidised fibres. The surface composition, morphology and wetting behaviour of the carbon fibres was characterised. The interaction between modified PVDF and the carbon fibres was studied by direct contact angle measurements between PVDF melt on single carbon fibres and by single fibre pull-out tests. The best wetting and adhesion behaviour was achieved between PVDF containing 5 ppm grafted maleic anhydride (MAH) and epoxy-sized carbon fibres. The addition of MAH-grafted PVDF to the unmodified PVDF caused the apparent interfacial shear strength to increase by 184%. The apparent interfacial shear strength of this fibre–matrix combination allowed for the utilisation of 100% of the yield tensile strength of PVDF. KW - A. Carbon fibres KW - A. Coupling agents KW - B. Interface KW - B. Adhesion KW - Wetting PY - 2008 DO - https://doi.org/10.1016/j.compscitech.2008.02.021 SN - 0266-3538 VL - 68 IS - 7-8 SP - 1766 EP - 1776 PB - Elsevier CY - Barking AN - OPUS4-18259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Godara, A. A1 - Gorbatikh, L. A1 - Kalinka, Gerhard A1 - Warrier, A. A1 - Rochez, O. A1 - Mezzo, L. A1 - Luizi, F. A1 - van Vuure, A.W. A1 - Lomov, S.V. A1 - Verpoest, I. T1 - Interfacial shear strength of a glass fiber/epoxy bonding in composites modified with carbon nanotubes N2 - In recent years, carbon nanotubes (CNTs) grown on fibers have attracted a lot of interest as an additional reinforcing component in conventional fiber-reinforced composites to improve the properties of the fiber/matrix interface. Due to harsh growth conditions, the CNT-grafted fibers often exhibit degraded tensile properties. In the current study we explore an alternative approach to deliver CNTs to the fiber surface by dispersing CNTs in the fiber sizing formulation. This route takes advantage of the developed techniques for CNT dispersion in resins and introduces no damage to the fibers. We focus on unidirectional glass fiber/epoxy macro-composites where CNTs are introduced in three ways: (1) in the fiber sizing, (2) in the matrix and (3) in the fiber sizing and matrix simultaneously. Interfacial shear strength (IFSS) is investigated using single-fiber push-out microindentation. The results of the test reveal an increase of IFSS in all three cases. The maximum gain (over 90%) is achieved in the composite where CNTs are introduced solely in the fiber sizing. KW - A. Carbon nanotubes KW - A. Hybrid composites KW - A. Polymer-matrix composites (PMCs) KW - B. Interfacial strength PY - 2010 DO - https://doi.org/10.1016/j.compscitech.2010.04.010 SN - 0266-3538 VL - 70 IS - 9 SP - 1346 EP - 1352 PB - Elsevier CY - Barking AN - OPUS4-22171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Bestimmung der Haftfestigkeit in Verbundwerkstoffen mittels Indentations- und Durchdrückexperimenten T2 - DGM Fachausschuss "Gefüge und Eigenschaften von Polymerwerkstoffen" CY - Hamburg, Germany DA - 2004-11-26 PY - 2004 AN - OPUS4-4705 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Mikromechanische Testmethoden zur Bestimmung von Haftung und Reibung in Faserverbundwerkstoffen T2 - Deutsches Zentrum für Luft- und Raumfahrt e.V. (DLR), Institut für Strukturmechanik CY - Braunschweig, Germany DA - 2004-02-04 PY - 2004 AN - OPUS4-4700 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Mechanische Charakterisierung des Faser-Matrix-Interface mit Einzelfaser-Tests T2 - Werkstoffwoche 2004: Kongress für innovative Werkstoffe, Verfahren und Anwendungen CY - Munich, Germany DA - 2004-09-21 PY - 2004 AN - OPUS4-4701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - A model of spherulitic crystallization based on growing lameallae T2 - 9th Microsymposium of Electron Microscopy in Materials Science CY - Lutherstadt Wittenberg, Germany DA - 2004-05-06 PY - 2004 AN - OPUS4-4702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Micro indentation near stiff-soft phase boundaries T2 - Polydays 2004 CY - Potsdam, Germany DA - 2004-10-04 PY - 2004 AN - OPUS4-4703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Micro indentation near stiff-soft boundaries T2 - "Nanomech5, 5th European Symposium on nano-Mechanical Testing" CY - Hückelhoven, Germany DA - 2004-09-07 PY - 2004 AN - OPUS4-4704 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Charakterisierung des Interface-Versagens in Faserverbundwerkstoffen mit mikromechanischen Testmethoden T2 - 5. Berliner Polymeren Tage CY - Potsdam, Germany DA - 1994-10-05 PY - 1994 AN - OPUS4-5910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Bestimmung der Interface-Festigkeit oder -Trennarbeit mit dem Pull-out-Versuch T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Kassel, Germany DA - 2005-04-06 PY - 2005 AN - OPUS4-6084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Bestimmung der Interface-Festigkeit in carbonfaserverstärkten Werkstoffen T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Kassel, Germany DA - 06.04.2005 PY - 2005 AN - OPUS4-6085 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Micro indentation and scratch tests for surface characterisation T2 - XXII. Donauländergespräche über die natürliche und künstliche Alterung von Polymeren CY - Berlin, Germany DA - 2001-09-17 PY - 2001 AN - OPUS4-7506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Munz, Martin A1 - Chung, Jae Un A1 - Kalinka, Gerhard ED - Possart, W. T1 - Mapping Epoxy Interphases T2 - 7th European Conference on Adhesion ; 7th EURADH CY - Freiberg, Germany DA - 2004-09-01 KW - Interface KW - Interphase KW - Epoxy KW - Copper (Cu) KW - Polyvinylpyrrolidone (PVP) KW - AFM/SFM KW - DSI KW - EDX/EDS KW - Stiffness KW - Modulus KW - Interdiffusion PY - 2005 SN - 3-527-31263-3 VL - 7 SP - 103 EP - 123 PB - Wiley-VCH CY - Weinheim AN - OPUS4-10894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Mikromechanik T2 - BAM, DGM Fachausschuss "Gefüge und Eigenschaften von Polymerwerkstoffen" CY - Berlin, Germany DA - 2003-12-05 PY - 2003 AN - OPUS4-4088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hinrichs, V. A1 - Kalinka, Gerhard A1 - Hinrichsen, G. T1 - An Avrami-based model for the description of the secondary crystallization of polymers N2 - A mathematical model for the description of the overall crystallization of polymers has been developed which separates the pure geometric spreading of the semicrystalline superstructures from the increasing crystallinity inside these entities. The model uses the Avrami theory for the geometric part and a freely optional function for the increasing local crystallinity. The two functions are combined by a mathematical procedure called convolution. The free option of the local crystallinity function enables this model to permit calculation of this function, which is not accessible to direct measurement. Thus with given Avrami parameters and measured values of the time-dependent overall crystallinity, this function of the local crystallinity (secondary crystallization function) can be calculated. The model has been applied to test data produced by computer simulations. KW - Thermoplaste KW - Kristallisation KW - Nachkristallisation KW - Sphärolithe KW - Kristallisationskinetik KW - Modellrechnung PY - 1996 DO - https://doi.org/10.1080/00222349608220382 SN - 0022-2348 SN - 1525-609X VL - 35 IS - 3-4 SP - 295 EP - 302 PB - Dekker Chemistry CY - New York, NY AN - OPUS4-11983 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Kalinka, Gerhard A1 - Auersch, W. T1 - Effect of Transcrystallization in Carbon Fiber Reinforced Poly(p/phenylene sulfide) Composites on the Interfacial Shear Strength Investigated with the Single Fiber Pull-Out Test N2 - The effect of transcrystallinity in carbon fiber reinforced poly(p-phenylene sulfide (PPS) composites on the apparent shear strength was investigated with the single fiber pull-out test. Transcrystalline zones around the reinforcing fibers do not seem to improve the adhesion level significantly. Neighbor fibers hinder the formation of the transcrystalline zone and a ductile fracture behavior can be observed. However, the apparent strength level is slightly higher for composites containing such reinforcing neighbor fibers compared with single fiber composite samples. During annealing a brittle interface can be formed in the multifiber composite yielding a higher level of the apparent shear strength. KW - Thermoplaste KW - Kristallisation KW - Transkristallisation KW - Interface KW - Verbundwerkstoffe KW - Pull-out KW - Haftung KW - Adhäsion KW - Reibung PY - 1996 DO - https://doi.org/10.1080/00222349608220393 SN - 0022-2348 SN - 1525-609X VL - 35 IS - 3-4 SP - 527 EP - 546 PB - Dekker Chemistry CY - New York, NY AN - OPUS4-11987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Charakterisierung des Faser-Matrix-Interface mit dem Indentation-Test T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Bayreuth, Germany DA - 1995-10-25 PY - 1995 AN - OPUS4-12008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Leistner, André A1 - Hampe, Andreas T1 - Characterisation of the fibre/matrix interface in reinforced polymers by the push-in technique N2 - The push-in test is the only micromechanical test method that is not restricted to artificial fibre/matrix arrangements, but allows the in situ characterisation of interfaces in composites fabricated and stressed under realistic conditions. However, with the application of this method to reinforced polymers some problems arise both in the mathematical model for evaluating test data and in the practical performance of the test. Because in some cases the deformation of the relatively compliant polymeric matrices cannot be neglected, an extension of the existing model is required. For this purpose, the elastic energy of the material around the debonded part of the fibre is estimated and included in the energy-balance analysis. Because of the small diameter of the fibres usually used for reinforcing polymers, a test apparatus was designed which ensures a high positioning accuracy in the xy plane as well as in the z direction. In order to minimise thermal and mechanical influences, the microscope for fibre selection and the force sensor/indenter are directly connected together and the apparatus is designed to be stiff in all components. A solid-state bending joint guarantees very precise control of the axial movement. Three examples of the application of this easy-to-handle and low-cost test apparatus are presented briefly in the paper: assess fibre/matrix combinations, measures to improve the interfacial adhesion and the influence of water on the interface. KW - Interface KW - Test method KW - Characterisation KW - Indentation KW - Push-in PY - 1997 SN - 0266-3538 VL - 57 IS - 8 SP - 845 EP - 851 PB - Elsevier CY - Barking AN - OPUS4-12011 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thomason, J.L. A1 - Kalinka, Gerhard T1 - A technique for the measurement of reinforcement fibre tensile strength at sub-millimetre gauge lengths N2 - The strength of composite reinforcement fibres is normally measured on samples of much greater length than the actual residual fibre lengths found in many composite materials. This is due to a number of limitations of the standard techniques which are employed. We present a description of a technique which enables values for the tensile strength of composite reinforcement fibres at short gauge lengths to be obtained. The technique is based on an adaptation of a micro-mechanical test apparatus for fibre pullout measurements. Data is presented which was obtained at gauge lengths of 180–380 µm on E-glass and S-2 glass® fibres taken from different chopped reinforcement products. The technique can be used at gauge lengths as short as 20 µm. The data indicates that the values of average fibre strength in these products are significantly below the pristine glass strength values. KW - Verstärkungsfaser KW - Kurzfaser KW - Längenabhängigkeit KW - Glass fibres KW - Strength KW - Mechanical testing KW - Festigkeit KW - Faser PY - 2001 DO - https://doi.org/10.1016/S1359-835X(00)00122-6 SN - 1359-835X VL - 32 IS - 1 SP - 85 EP - 90 PB - Elsevier CY - Oxford AN - OPUS4-12012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hampe, Andreas A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Schulz, Eckhard T1 - An advanced equipment for single-fibre pull-out test designed to monitor the fracture process KW - Verbundwerkstoffe KW - Thermoplaste KW - Adhäsion KW - Reibung KW - Haftung KW - Interface KW - Schubfestigkeit KW - Scherfestigkeit KW - Messmethode PY - 1995 SN - 0010-4361 VL - 26 IS - 1 SP - 40 EP - 46 PB - Butterworth-Heinemann CY - Guildford, Surrey AN - OPUS4-11988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Hampe, Andreas T1 - Pull-out of Single Fibres KW - Verstärkungsfaser KW - Verbundwerkstoffe KW - Interface KW - Adhäsion KW - Reibung KW - Haftung KW - Thermoplast PY - 1994 SN - 0945-0084 VL - 84 IS - 5 SP - 25 EP - 26 PB - Hanser CY - München AN - OPUS4-11989 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auer, C. A1 - Kalinka, Gerhard A1 - Krause, T. A1 - Hinrichsen, G. T1 - Crystallization Kinetics of Pure and Fiber-Reinforced Poly(phenylene Sulfide) KW - Verbundwerkstoffe KW - Thermoplaste KW - Kristallisation KW - Kristallisationskinetik KW - Erstarrung KW - Avrami KW - Modellrechnung KW - Simulation PY - 1994 SN - 0021-8995 SN - 1097-4628 VL - 51 SP - 407 EP - 413 PB - Wiley InterScience CY - Hoboken, NJ AN - OPUS4-11991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, T. A1 - Kalinka, Gerhard A1 - Auer, C. A1 - Hinrichsen, G. T1 - Computer Simulation of Crystallization Kinetics in FIber-Reinforced Composites KW - Verbundwerkstoffe KW - Thermoplaste KW - Kristallisation KW - Kristallisationskinetik KW - Erstarrung KW - Avrami KW - Modellrechnung KW - Simulation PY - 1994 SN - 0021-8995 SN - 1097-4628 VL - 51 SP - 399 EP - 406 PB - Wiley InterScience CY - Hoboken, NJ AN - OPUS4-11992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Kalinka, Gerhard A1 - Meretz, S. A1 - Hampe, Andreas T1 - Einzelfaserauszug - Eine Methode zum Bestimmen der Grenzflächenfestigkeit KW - Verstärkungsfaser KW - Verbundwerkstoffe KW - Interface KW - Adhäsion KW - Reibung KW - Haftung KW - Thermoplast PY - 1994 SN - 0023-5563 VL - 84 IS - 5 SP - 608 EP - 610 PB - Hanser CY - München AN - OPUS4-11994 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nowak, H. A1 - Kalinka, Gerhard A1 - Hinrichsen, G. T1 - Investigations on the cold crystallization of pure and filled PETP by dielectric measurements N2 - The cold crystallization of pure and filled poly(ethylene terephthalate) (PETP) after quenching from the melt has been investigated by dielectric measurements in two different modes: The first one using constant heating-rate (in the temperature range from 320 to 480 K) and the second one under isothermal conditions (at 378 K). The complex dielectric constant (ε´, tan δ) is influenced by crystallization. Two α-relaxation regions are identified: The αa-relaxation region from the pure amorphous phase and the α´-relaxation region from the spherulitic phase. The investigations on the filled systems (PETP + 10% aramid puple, PETP + 30% short glass fibres) prove that an influence of the fillers on the time delay and rate of crystallization and on the geometry of the growing spherulites exists. KW - Verbundwerkstoffe KW - Gefüllte Kunststoffe KW - Elektrische Eigenschaften KW - Verlustfaktor KW - Dielektrische Analyse PY - 1993 SN - 0323-7648 SN - 1521-4044 VL - 44 IS - 1 SP - 25 EP - 28 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-11995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Boro, I. A1 - Augustin, G. A1 - Hampe, Andreas A1 - Hinrichsen, G. T1 - Ermüdungsverhalten von Hochleistungs-Faserverbundwerkstoffen mit thermoplastischer Matrix KW - Verbundwerkstoffe KW - Ermüdung KW - Biegeschwingung KW - Thermoplaste KW - Glasfaser PY - 1990 SN - 0023-5563 VL - 80 IS - 5 SP - 626 EP - 630 PB - Hanser CY - München AN - OPUS4-11996 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Boro, I. A1 - Augustin, G. A1 - Hampe, Andreas A1 - Hinrichsen, G. T1 - Fatigue Behaviour of High-Performance Fibre-Reinforced Composites with a Thermoplastic Matrix KW - Verbundwerkstoffe KW - Ermüdung KW - Biegeschwingung KW - Thermoplaste KW - Glasfaser PY - 1990 SN - 0723-0192 VL - 80 IS - 5 SP - 36 EP - 38 PB - Hanser CY - Munich AN - OPUS4-11999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hinrichs, V. A1 - Leistner, A. A1 - Kalinka, Gerhard A1 - Schulz, Eckhard A1 - Hinrichsen, G. T1 - Viscoelastic properties of the interphase in fibre reinforced polymers - measurement and simulation KW - Polymer KW - Glass fibre KW - Interphase KW - Coating KW - Glass transition KW - Dynamic KW - Viscoelastic PY - 1999 VL - 6 IS - 2 SP - 93 EP - 101 PB - North-Holland CY - New York, NY AN - OPUS4-12003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalinka, Gerhard A1 - Hinrichsen, G. T1 - Two-dimensional computer simulation of spherulite formation by branching lamellae KW - Thermoplaste KW - Kristallisation KW - Sphärolithe KW - Lamellen KW - Modellrechnungen PY - 1997 SN - 0323-7648 SN - 1521-4044 VL - 48 SP - 256 EP - 261 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-12004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Computersimulation der lamellar-shpärolithischen Kristallisation bei Polymeren T2 - 5. Berliner Polymeren-Tage CY - Potsdam, Germany DA - 1994-10-05 PY - 1994 AN - OPUS4-12007 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Untersuchungs des Ermüdungsverhaltens glasfaserverstärkter Thermoplaste mittels Schwingungsmessungen T2 - Zweites Werkstoffsymposium Neue Verbundwerkstoffe CY - Regensburg, Germany DA - 1990-10-05 PY - 1990 AN - OPUS4-12127 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Energy Quantification of Interface Debonding Processes Using 'Stiff' Test Devices T2 - Gordon Conference on Composite Materials CY - San Buenaventura, CA, USA DA - 2001-01-28 PY - 2001 AN - OPUS4-12108 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Characterization of the fibre-matrix interface with the indentation technique T2 - 6th International Conference on Composite Interfaces (ICCI-VI) CY - Zichron Ya'akov, Israel DA - 1996-05-05 PY - 1996 AN - OPUS4-12086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Friction Measurement on fiber reinforced polymer composites with using the indentation technique T2 - European Conference on Composite Materials ECCM-8 CY - Naples, Italy DA - 1998-06-03 PY - 1998 AN - OPUS4-12089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Energy orientated data interpretation of pull-out and push-out test for the investigation of residual stresses T2 - Interface Phenomena in Composite Materials CY - Berlin, Germany DA - 1999-09-08 PY - 1999 AN - OPUS4-12093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Ermüdungsverhalten von faserverstärkten Thermoplasten T2 - Präsentationsveranstaltung des Berliner Verbands für Polymerforschung CY - Berlin, Germany DA - 1989-05-18 PY - 1989 AN - OPUS4-12094 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Charakterisierung des Interface-Versagens in Faserverbundwerkstoffen mit mikromechanischen Testmethoden T2 - 5. Berliner Polymeren-Tage CY - Potsdam, Germany DA - 1994-10-05 PY - 1994 AN - OPUS4-12096 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Charakterisierung des Faser-Matrix-Interface mit dem Indentation-Test T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Bayreuth, Germany DA - 1995-10-24 PY - 1995 AN - OPUS4-12097 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Energy Dissipation of the Fibre-Matrix Debonding Process Investigated with the Indentation Technique T2 - Interfacial Phenomena of Composite Materials IPCM'95 CY - Eindhoven, Netherlands DA - 1995-09-11 PY - 1995 AN - OPUS4-12098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Der Einfluss der Transkristallisation auf die scheinbare Scherfestigkeit von kohlefaserverstärktem Polyphenylensulid (PPS) mit der Einzelfaserauszugsmethode T2 - Verbundwerkstoffe und Werkstoffverbunde CY - Bayreuth, Germany DA - 1995-10-24 PY - 1995 AN - OPUS4-12099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Energy based characterization of the fiber-matrix interface unsing the pull-out and the push-out test T2 - Micro Mat '97 CY - Berlin, Germany DA - 1997-04-16 PY - 1997 AN - OPUS4-12100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -