TY - JOUR A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Hensel, Christina A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Preventing the explosion of acetylene cylinders involved in fire with help of numerical modeling JF - Journal of loss prevention in the process industries N2 - The current paper describes a mathematical model, which was developed to simulate the heat transfer in acetylene cylinders during exposure to a fire. The cases of a direct engulfment of the cylinder in the flames and of exposure to a distant fire were considered. Furthermore, the model was also applied to the prediction of the heat transfer during the cooling with water of heated acetylene cylinders, in order to assess the effectiveness of this procedure as a measure to prevent the burst of the cylinder. To provide data for the definition and validation of the model a total of 13 bonfire tests with 8.9-, 10- and 50-dm³-cylinders were performed, where pressure and temperature measurements in the samples were performed. During 5 experiments the fire was extinguished before the expected cylinder burst and a cooling with water was applied. In the paper a short description of the experimental set-up and of the test results is given. Finally, a comparison with the model predictions is provided, showing reasonable agreement. KW - Acetylene cylinders KW - Fire KW - Explosion KW - Cooling KW - Numerical model PY - 2012 DO - https://doi.org/10.1016/j.jlp.2011.10.006 SN - 0950-4230 SN - 1873-3352 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 25 IS - 2 SP - 364 EP - 372 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-25137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Ferrero, Fabio A1 - Schmidtchen, Ulrich T1 - Acetylenflaschen im Feuer JF - Technische Sicherheit - Brandschutz N2 - Acetylen ist eines der wichtigsten technischen Gase und findet insbesondere Anwendung beim Schweißen und Schneiden verschiedener Werkstoffe. Damit Acetylen in entsprechenden Mengen vor Ort zur Verfügung gestellt werden kann, wird es in Druckgasbehälter abgefüllt. Im Falle eines Brandes stehen Acetylenflaschen im Verdacht, jederzeit – auch nach Löschen des Feuers – aufgrund einer möglicherweise initiierten Zerfallsreaktion zu bersten. Um insbesondere Personenschäden zu vermeiden, evakuieren und sperren die Rettungskräfte einen Sicherheitsbereich mit einem Radius von mindestens 200 m um die verdächtige Flasche ab. Gleichzeitig wird umgehend mit der Kühlung der Flasche begonnen. Wie lange muss aber eine Acetylenflasche gekühlt werden, bis sie sicher abtransportiert werden kann, und wie lange muss der Sicherheitsbereich mit dem großen Radius aufrecht erhalten werden? Diesen Fragen ist die BAM in den vergangenen Jahren im Rahmen verschiedener Untersuchungen und Projekte nachgegangen. KW - Acetylen KW - Druckbehälter KW - Poröses Material KW - Lösungsmittel PY - 2012 SN - 2191-0073 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 2 IS - 4 SP - 19 EP - 25 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-25902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Gebauer, Marek A1 - Grüneberg, Miriam A1 - Müller, Ralf A1 - Eliezer, D. T1 - Pressure resistance of glass capillaries for hydrogen storage T2 - Workshop "Materials challenges for clean enery" im Rahmen des 3rd World Materials Research Institute Forum, NIST T2 - Workshop "Materials challenges for clean enery" im Rahmen des 3rd World Materials Research Institute Forum, NIST CY - Washington, D.C., USA DA - 2009-06-22 PY - 2009 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. AN - OPUS4-19677 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Modeling the heat transfer in acetylene cylinders during and after the exposure to fire JF - Journal of loss prevention in the process industries N2 - In this paper two different approaches for predicting the heating-up of an acetylene cylinder involved in a fire and the afterward cooling with water are presented. In the simulations polynomial functions were used to describe the temperature dependency of the thermal properties of the cylinder interior, which is a complex system composed by a solid porous material, a solvent (typically acetone) and acetylene dissolved in it. Model equations covered heat conduction in the cylinder interior and at its walls. In the first approach the cylinder surroundings were simulated as a further domain constituted by CO2, during the fire exposure, and for water, during the cooling. In this domain the coupled heat transfer (convection and conduction) and the momentum equation (Navier-Stokes) were solved. In the second approach no further domain was considered but boundary conditions were set directly on the cylinder walls. Results of the calculations performed with both approaches are presented. This work could prove helpful in predicting to which extent the interior of an acetylene cylinder exposed to fire reaches temperatures capable of initiating the decomposition of acetylene and to determine how long a water cooling should be applied, so that the system is brought again under non-critical conditions. KW - Safety KW - Acetylene KW - Heat transfer KW - Fire KW - Water cooling PY - 2010 DO - https://doi.org/10.1016/j.jlp.2010.06.012 SN - 0950-4230 SN - 1873-3352 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 23 SP - 654 EP - 661 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-21808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Hensel, Christina A1 - Kreißig, Michael A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Unterfeuerung von Acetylendruckgasbehältern T2 - 10. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit T2 - 10. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Deutschland DA - 2010-11-04 KW - Sicherheit KW - Acetylen KW - Feuer KW - Wasserkühlung KW - Wärmeübertragung PY - 2010 SN - 978-3-89746-119-2 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. IS - Paper N-02 SP - 1 EP - 20 CY - Frankfurt/M. AN - OPUS4-22351 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeps, Robert A1 - Rosenow, B. A1 - Kluge, Martin A1 - Blanchard, R. A1 - Holtappels, Kai T1 - Druckentlastungsvorgänge in großvolumigen Behältern T2 - 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik (BAM-PTB-Kolloquium) N2 - Es wurden Druckentlastungsvorgänge in einem 5 m³ Autoklav mit einem L/D-Verhältnis von 1,14 nach der Zündung von Methan-Luft-Gemischen untersucht. Schwerpunkt der Arbeit war die Bestimmung der Explosionsdrücke, der zeitlichen Druckanstiege bzw. der KG-Werte und der reduzierten Explosionsdrücke in Abhängigkeit der Methankonzentration. Im geschlossenen Behälter wurden die Explosionsdrücke und zeitlichen Druckanstiege für Methan-Luft-Gemische mit Methankonzentrationen von 5,9 Vol-% bis 13,5 Vol-% ermittelt. Die Ergebnisse zeigen gute Übereinstimmung mit den Literaturwerten. Weiter wurden Druckentlastungsversuche mit einer kreisrunden Entlastungsfläche von 0,011 m² und einer Druckentlastungsfolie mit einem statischen Ansprechdruck von 1,94 bar durchgeführt. Hierbei wurden Gemische mit Methankonzentrationen von 5,9 Vol-% bis 14,3 Vol-% untersucht. Dabei zeigte sich, dass die vergleichsweise kleine Entlastungsfläche nur dann zu reduzierten Explosionsdrücken gleich dem statischen Ansprechdruck der Berstfolie führte, wenn die Methankonzentration ≤ 5,9 Vol-% oder ≥ 14,0 Vol-% betrug. Bei allen anderen untersuchten Methankonzentrationen führten die durch die Druckentlastung induzierten Turbulenzen zu einer Beschleunigung der Verbrennungsreaktion und zu Explosionsdrücken vergleichbar denen im geschlossenen Behälter. T2 - 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik (BAM-PTB-Kolloquium) CY - Berlin, Germany DA - 14.06.2016 KW - Druckentlastung KW - Up-Scale KW - Deflagration KW - Sicherheitstechnik PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 VL - 2016 SP - 21 EP - 28 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-37176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Gebauer, Marek A1 - Grüneberg, Miriam A1 - Eliezer, D. T1 - Hydrogen storage in glass capillary arrays for portable and mobile systems T2 - 3rd International conference on hydrogen safety (Proceedings) T2 - 3rd International conference on hydrogen safety CY - Ajaccio, Corsica, France DA - 2009-09-16 KW - Glaskapillare KW - Hochdruckwasserstoff KW - Gasspeicherung KW - Mobile Speichersysteme PY - 2009 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. IS - ID 204 SP - 1 EP - 8(?) AN - OPUS4-19905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Schmidtchen, Ulrich A1 - Pahl, Robert A1 - Noack, Jennifer A1 - Kolvitz, Kristian A1 - Runge, Thomas A1 - Holtappels, Kai A1 - Hensel, Christina A1 - Bönig, Jürgen A1 - Schulze, Uwe A1 - Askar, Enis A1 - Frank, M. A1 - Thornton, D. T1 - Experimentelle und numerische Untersuchungen des Verhaltens von Acetylenflaschen im Feuer T2 - 12. Kolloquium zu Fragen der chemischen und physikalischen Sicherheitstechnik T2 - 12. Kolloquium zu Fragen der chemischen und physikalischen Sicherheitstechnik CY - Berlin, Deutschland DA - 2010-06-15 KW - Acetylendruckgasbehälter KW - Unterfeuerung KW - Aufheizverhalten KW - CFD-Modellierung PY - 2010 SN - 978-3-9813550-1-7 SN - 0938-5533 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 70 EP - 72 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-21488 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Hensel, Christina A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - The behavior of acetylene cylinders involved in fire: An experimental and numerical analysis T2 - 19th International congress of chemical and process engineering (CHISA 2010) / 7th European congress of chemical engineering (ECCE-7) N2 - Fire exposure tests of acetylene cylinders were performed. The purpose of the experiments was to gather information on the behavior in fire of such vessels, depending on the initial charge of acetylene. In fact "empty" acetylene cylinders still contain the solvent in which acetylene is dissolved plus the amount of acetylene to saturation at atmospheric pressure and ambient temperature and may still constitute a threat to safety. In the fire exposure tests performed the hazardousness of these vessels was demonstrated, since it was observed that not only fully charged acetylene cylinders but also cylinders with saturated solvent can explode, provided the heat transfer to the vessel is sufficient. The times to explosion were shorter for fully charged cylinders, due to the higher initial pressure and to the faster pressure increase. The effects of the explosions are comparable for both fully charged cylinders and for cylinders with saturated solvent, except for the smaller fireball which is produced in the second case, due to the smaller amount of fuel available. In both cases the cylinder walls or at least fragments can fly further than 100 m away from the burst location. Results of the experiments are presented in the paper. During the tests, temperature measurements at the cylinder walls and in the cylinder interior were performed. Furthermore, the pressure in the cylinder was recorded. The collected data will serve for the validation of a numerical model for the simulation of the heating of acetylene cylinders involved in fire and of the afterward cooling with water, which has been developed. The constitutive model equations and the results of some simulations are presented in the paper. T2 - 19th International congress of chemical and process engineering (CHISA 2010) / 7th European congress of chemical engineering (ECCE-7) CY - Prague, Czech Republic DA - 2010-08-28 KW - Safety KW - Acetylene KW - Heat transfer KW - Fire KW - Simulation PY - 2010 SN - 978-80-02-02210-7 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. IS - F3.1 / 0973 SP - 1 EP - 13 CY - Prague, Czech Republic AN - OPUS4-21923 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Holtappels, Kai A1 - Ried, Peter A1 - Krause, Heike A1 - Eliezer, D. T1 - Pressure resistance of glass capillary structures for gas storage purposes T2 - First International Conference on Materials for Energy T2 - First International Conference on Materials for Energy CY - Karlsruhe, Germany DA - 2010-07-04 PY - 2010 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, Martin - Birth name of Kluge, Martin: Beckmann-Kluge, Martin AN - OPUS4-24056 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Prevention of the explosion of acetylene cylinders involved in fire: experiments and simulations T2 - 23rd ICDERS 2011 N2 - In order to assess the effectiveness of water cooling of acetylene cylinders involved in fire, a total of 13 bonfire tests with 8.9-, 10 and 50-l-cylinders were performed. During the experiments the pressure in the cylinder and the temperature at different locations within the porous material and on the Shell surface as well as the flame temperature were measured. Overall 8 burst tests were performed, in order to determine the times to explosion for the cylinders. Cylinders failed not later than 15 minutes from the ignition of the bonfire, often with generation of a fireball. During the other 5 tests, the fire was extinguished before the expected burst and the cylinder was cooled with water. In 2 of the 5 extinction experiments, the explosion of the cylinder could be prevented. Noticeably, in one case the on-set of the decomposition of acetylene had already been observed, before the cooling was started. In spite of that, the cooling was still effective. The interpretation of the current results and of the data from previous tests with 40-l-cylinder suggests that single acetylene cylinders involved in fire might be saved by cooling, if their pressure does not exceed a value of about 45 bara. The recorded values of pressure and temperature were used to develop and validate a mathematical model for the prediction of the heat transfer in acetylene cylinders during the exposure to fire and the afterward cooling. The predictions agreed well with the experimental results. T2 - 23rd ICDERS 2011 CY - Irvine, CA, USA DA - 24.07.2011 KW - Acetylene KW - Gas cylinders KW - Fire exposure KW - Decomposition PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. IS - Paper 132 SP - 1 EP - 6 AN - OPUS4-24153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Holtappels, Kai T1 - COMSOL Multiphysics® as a Tool to Increase Safety in the Handling of Acetylene Cylinders Involved in Fires T2 - COMSOL Conference 2009 (Proceedings) N2 - In this paper a mathematical model for predicting the heating-up of an acetylene cylinder involved in a fire is presented. In the simulations polynomial functions were used to describe the temperature dependency of the thermal properties of the cylinder interior, which is a complex system composed by a solid porous material, a solvent and acetylene dissolved in it. Model equations covered heat conduction in the cylinder interior and at its walls, while the fire surrounding the cylinder was simulated by solving the coupled heat transfer and the momentum equation. Results of the calculations and the effects of some model parameters are discussed. T2 - COMSOL Conference 2009 CY - Milan, Italy DA - 2009-10-14 KW - Acetylene KW - Safety KW - Heat transfer KW - Momentum transfer PY - 2009 SN - 978-0-9825697-0-2 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 1 EP - 5 AN - OPUS4-20261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kluge, Martin A1 - Eliezer, D. A1 - Holtappels, Kai A1 - Krause, Heike A1 - Ried, Peter T1 - Pressure resistance of glass capillary structures for gas storage purposes T2 - 1st International conference on materials for energy (Proceedings) T2 - 1st International conference on materials for energy CY - Karlsruhe, Germany DA - 2010-07-04 KW - Dimerization KW - Numerical simulation KW - CFD KW - FEM KW - Self heating KW - TFE PY - 2010 SN - 978-3-89746-117-8 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 752 EP - 754 AN - OPUS4-23042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Gebauer, Marek A1 - Eliezer, D. T1 - Pressure resistance of glass capillaries for hydrogen storage JF - Materials Testing N2 - Ein entscheidendes Problem neuer Wasserstofftechnologien ist die leichte und sichere Lagerung ausreichender Mengen an Wasserstoff insbesondere für Nutzung bei tragbaren oder mobilen Anwendungen. Eine neue und innovative Technologie basierend auf gebündelte Kapillaren wurde entwickelt. Diese Systeme garantieren eine sichere Speicherung, Lagerung und kontrollierte Freisetzung von Wasserstoff, obgleich Speicherdrücke bis 1200 bar angewendet werden. Die neue Technologie ermöglicht die Lagerung einer erheblich größeren Menge Wasserstoff als andere Systeme und übertraf bereits die Zielsetzung des DOE 2010. Es wird erwartet, die DOE-Zielsetzung für das Jahr 2015 bereits in naher Zukunft zu erreichen. Hauptaspekt für die Speichertechnologie ist die Druckfestigkeit der Glaskapillaren. Es ist weithin bekannt, dass besonders Quarz eine dreimal höhere Festigkeit als Stahl hat. Gleichzeitig ist die Dichte ungefähr dreimal niedriger, was bedeutet, dass viel weniger Material notwendig ist, um die gleiche Druckfestigkeit zu erreichen. Die Druckfestigkeit einzelner Kapillare ist in der Abhängigkeit der Materialien, der Abmessungen, der Wandstärke etc. ermittelt worden, um optimale Parameter für die "finalen" Kapillaren herauszufinden. KW - Wasserstoffspeicherung KW - Glasstruktur KW - Druckefestigkeit KW - Berstdruck PY - 2011 SN - 0025-5300 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 53 IS - 1-2 SP - 14 EP - 18 PB - Hanser CY - München AN - OPUS4-23043 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blanchard, R. A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Schildberg, H.-P. A1 - Zeps, Robert ED - de Rademacher, E. ED - Schmelzer, P. T1 - Sizing of Explosion Pressure Relief using the Efflux Function T2 - Chemical Engineering Transactions N2 - Determination of deflagration venting requirements in chemical/process plants is usually carried out using well established standards employing an empirically based formula. However, this formula is shown to have severe shortcomings, especially in the range of low KG-values, where either negative or inconceivably large venting areas can be predicted. Due to these shortcomings a method has been developed using the efflux function for gases as a basis to predict the mass flow through a vent opening in a vessel during an internal explosion. The simulated rise in pressure due to the internal explosion is quantitatively determined from the KG-value, with the mass flow through the vent opening in the vessel resulting from the pressure difference between the vessel and its surroundings. This enables the maximum overpressure as a function of the pressure relief surface area to be predicted. The method takes into account the temperature of the efflux gases and turbulence enhancement brought about by the venting process. In the following paper explosion pressure relief experiments are described and the results from these experiments are compared to predictions from the efflux method. It is shown that by adjusting the assumed turbulence which evolves during the venting process, the reduced explosion pressure can be reasonably well reproduced. T2 - 15th International Symposium on Loss Prevention and Safety Promotion in the Process Industries and accompanying exhibition CY - Freiburg, Germany DA - 05.06.2016 KW - Deflagration KW - Explosion KW - Pressure relief KW - Venting KW - Efflux PY - 2016 SN - 978-88-95608-39-6 DO - https://doi.org/10.3303/CET1648082 SN - 2283-9216 VL - 48 SP - 487 EP - 492 PB - AIDIC Servizi S.r.l CY - Milano, Italy AN - OPUS4-37918 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Kluge, Martin A1 - Tschirschwitz, Rico A1 - Holtappels, Kai A1 - Pelzl, T. T1 - Feuerwehrmerkblätter zu Druckgasbehältern im Brandeinsatz T2 - Proceedings der 13. Fachtagung Anlagen, Arbeits- und Umweltsicherheit N2 - Die BAM hat zum Verhalten von Acetylen- und Propangasflaschen bei einer Vollunterfeuerung umfangreiche Versuchsreihen zur Auswirkungsbetrachtung des Behälterversagens auf dem TTS durchgeführt. In Zusammenarbeit mit verschiedenen Partnern entstanden zwei Merkblätter mit praktischen Hinweisen für Einsatzkräfte, die die aktuellen Forschungsarbeiten der BAM berücksichtigen. T2 - 13. Fachtagung Anlagen, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 16.11.2017 KW - Behälterversagen KW - Gassicherheit KW - Feuerwehr KW - Acetylen KW - Propan PY - 2017 SN - 978-3-96057-032-5 SP - 1 EP - 9 AN - OPUS4-42953 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krentel, Daniel A1 - Tschirschwitz, Rico A1 - Kluge, Martin A1 - Grasse, Dennis A1 - Holtappels, Kai A1 - Pelzl, T. T1 - Umgang mit Druckgasbehältern im Brandeinsatz JF - BRANDSchutz N2 - Regelmäßig werden Einsatzkräfte der Feuerwehr bei Brandeinsätzen mit brand- bzw. wärmebeaufschlagten Druckgasbehältern konfrontiert. Aufgrund ihrer großen Verbreitung handelt es sich dabei oftmals um Propan- oder Acetylengasflaschen. Propangasflaschen mit Füllmengen bis 33 Kilogramm sind in flächendeckender Verwendung zum Beispiel in Handwerksbetrieben, Produktionsbereichen, Baustellen und Restaurants, werden aber oftmals auch zum Heizen und Kochen im Privatbereich verwendet. Acetylengasflaschen sind in Verbindung mit entsprechenden Sauerstoffbehältern ebenso in Werkstätten, gewerblichen Anlagen und auf Baustellen zum Autogenschweißen und thermischen Trennen in vielfacher Verwendung. Beide Arten von Druckgasbehältern sind darüber hinaus auch im Straßenverkehr als Gefahrgut und in kleineren Mengen auch als private Fracht anzutreffen. Die Deutsche Gesetzliche Unfallversicherung (DGUV) hat zusammen mit weiteren Experten als Hilfestellung und aufgrund neuer wissenschaftlicher Erkenntnisse zwei DGUV-Informationen für Einsatzkräfte zum Umgang mit wärmebeaufschlagten Druckgasbehältern erstellt. KW - Behälterversagen KW - Brandbekämpfung KW - Feuerwehr KW - Acetylen KW - Propan PY - 2019 SN - 0006-9094 VL - 73 IS - 2 SP - 103 EP - 109 PB - W. Kohlhammer CY - Stuttgart AN - OPUS4-47445 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -