TY - JOUR A1 - Kato, K. A1 - Watanabe, T. A1 - Heine, Hans-Joachim A1 - Boissière, Claudia A1 - Schulz, Gert A1 - Woo, J.-C. A1 - Kim, J.S. A1 - Sang-Hyub, O. A1 - Bae, H. K. A1 - Kim, Y.D. A1 - Qiao, H. A1 - Guenther, F.R. A1 - Roderick, G. C. A1 - Miller, W. A1 - Smeulders, D. A1 - Botha, A. A1 - van Rensburg, M.J. A1 - Tshilongo, J. A1 - Leshabane, N. A1 - Ntsasa, N. A1 - Milton, M. A1 - Vargha, G. A1 - Harling, A. A1 - Konopelko, L. A1 - Kustikov, Y.A. A1 - Vasserman, I.I. A1 - Zavyalov, S. V. A1 - Popova, T.A. A1 - Pankratov, V.V. A1 - Pir, M.N. A1 - Maltsev, M.A. A1 - Oudwater, R. A1 - Persijn, S. A1 - van Wijk, J. A1 - Wessel, R. M. T1 - International comparison CCQM-K66: Impurity analysis of methane JF - Metrologia N2 - This key comparison was performed to demonstrate the capability of NMIs to analyse the purity of methane for use as a source gas in the preparation of standard gas mixtures. This capability is an essential requirement for the preparation of accurate standards of natural gas and some other fuels. Since it is difficult to carry out a comparison with individual samples of pure gas, the sample for this comparison was a synthetic mixture of high purity methane with selected added impurities of nitrogen, argon, carbon dioxide and ethane. These mixtures were prepared by a gas company as a batch of 10 cylinders and their homogeneity and stability were evaluated by NMIJ. The KCRVs for the four different analytes in this key comparison are based on a consensus of values reported by participants. The uncertainties in the degrees of equivalence were calculated by combining the reported uncertainties with the homogeneity of the samples and the uncertainty of the KCRV. The results submitted are generally consistent with the KCRV within the estimated uncertainties. Finally, this comparison demonstrates that the analysis of nitrogen, argon, carbon dioxide and ethane in methane at amount fractions of 1 µmol/mol to 5 µmol/mol is generally possible with an uncertainty of 5% to 10%. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA). DatesIssue 1A (Technical Supplement 2012) KW - Ringversuch KW - Methan KW - Spurenverunreinigungen KW - Gaschromatographie PY - 2012 DO - https://doi.org/10.1088/0026-1394/49/1A/08001 SN - 0026-1394 SN - 1681-7575 VL - 49 IS - 08001 SP - 1 EP - 76 PB - Inst. of Physics Publ. CY - Bristol AN - OPUS4-25929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shirai, K. A1 - Namba, K. A1 - Wataru, M. A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Probst, Ulrich A1 - Jaunich, Matthias A1 - Schulz, Sebastian T1 - Numerical evaluation of the long-term sealing performance of the silver gasket for dual purpose metal cask under high temperature T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials (Proceedings) N2 - It is important to evaluate the effect of thermal ageing on the sealing performance of metal gaskets under high temperature for long-term usage. Therefore, in order to gain representative data for this kind of metal-sealed lid System, BAM is currently performing laboratory tests of different gasket types with aluminum and silver jackets at three different temperatures under static conditions up to four years so far, using test flanges for gaskets with full scale cross section diameter but much smaller outer diameter. On the other hand, in order to investigate the applicability of the numerical methodology to evaluate the long-term behavior of the metal gaskets, such as a correlation between seal pressure force and holding time, CRIEPI is developing a modeling method including material tests (tensile and creep tests) at high temperature. In this paper, the applicability of the finite element method (ABAQUS) to predict the recovery displacement and residual seal pressure force of the gasket complex was verified by comparing the calculated values with BAM’s laboratory test results under the joint research agreement between BAM and CRIEPI. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Metal seals KW - Extended storage KW - Long-term storage KW - Dual purpose cask PY - 2013 SP - 1 EP - 8 PB - Omnipress AN - OPUS4-31947 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wachtendorf, Volker A1 - Gaszner, K. A1 - Schulz, Ulrich A1 - Trubiroha, Peter T1 - Aufklärung der Ursachen für Lackschäden durch Umwelteinflüsse und Entwicklung praxisgerechter Prüfmethoden - Teil 1: Übertragung der Jacksonville Bewitterung auf eine Labor-Prüfmethode am Beispiel dekorative Eigenschaften und Kratzbeständigkeit T2 - DFO-Technologie-Tage Neue Entwicklungen zur Qualitätsprüfung in der Lackiertechnik (Berichtsband / Deutsche Forschungsgesellschaft für Oberflächenbehandlung e.V., DFO Nr. 50) T2 - DFO-Technologie-Tage Neue Entwicklungen zur Qualitätsprüfung in der Lackiertechnik CY - Münster, Deutschland DA - 2002-03-19 PY - 2002 SN - 3-932287-50-9 IS - 50 SP - 55 EP - 63 PB - DFO CY - Düsseldorf AN - OPUS4-1317 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kricheldorf, H. A1 - Hauser, K. A1 - Krüger, Ralph-Peter A1 - Schulz, Günter T1 - Macrocycles 12. Ring-Opening Polycondensations of Tin-Containing Macrocycles with Bis(Thioarylester)s JF - Journal of macromolecular science A N2 - 2,2-Dibutyl-2-stanna-1,3-dioxepane (DSDOP) was polycondensed with bis(4-chlorothiophenyl) suberat under various reaction conditions, but only moderate molecular weights (Mn 10000) were obtained. The MALDI-TOF mass spectrosmetry revealed the formation of cyclic oligo- and polyesters in addition to linear species having OH, CO2H, and unreacted 4-chlorothiophenyl ester endgroups. Furthermore, -Caprolactone (-CL) was polymerized with DSDOP as the initiator at monomer/initiator (M/I) ratios of 20 and 50. The resulting tin-containing macrocyclic polylactones were reacted with sebacic acid bis(4-thiocresyl)ester at three different temperatures and with different reaction times. Analogous polycondensations were conducted with suberic acid bis(4-chlorothiophenyl) ester. The presence of thioarylester endgroups in the isolated polyesters was checked by 1H NMR spectroscopy. The highest conversions were found at long reaction times (24 or 72 hours), or after the addition of pyridine and N,N-dimethylaminopyridine as catalysts. Despite high conversions, the number average molecular weights (Mn's) did not exceed values around 20000. Even in the samples having the highest molecular weights, unreacted 4-chlorothiophenylester endgroups were detected by GPC measurements evaluated with a UV-detector. It is concluded that both factors, cyclization and incomplete conversion, contribute to the limitation of the chain growth. KW - Ring-Opening Polycondensations KW - Macrocycles KW - Polyesters PY - 2000 DO - https://doi.org/10.1081/MA-100101099 SN - 1060-1325 SN - 1520-5738 VL - 37 IS - 4 SP - 379 EP - 394 PB - Taylor & Francis CY - Philadelphia, PA AN - OPUS4-2167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana A1 - Krüger, Ralph-Peter A1 - Much, Helmut A1 - Schulz, Günter A1 - Spranger, K. T1 - Neue Möglichkeiten der Polymercharakterisierung durch 2D-HPLC, Kopplung mit spektroskopischen Methoden und MALDI-TOF-MS T2 - Tagungsband der Gesellschaft Deutscher Chemiker, "Klassische Polymere im Aufwind, Polymerchemie aktuell" T2 - Gesellschaft Deutscher Chemiker, "Klassische Polymere im Aufwind, Polymerchemie aktuell" CY - Dresden, Deutschland DA - 1996-03-25 PY - 1996 CY - Dresden AN - OPUS4-2212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Much, Helmut A1 - Schulz, Günter A1 - Spranger, K. ED - Günther, W. T1 - MALDI-TOF-MS zur Charakterisierung von synthetischen Polymeren in Kopplung mit der HPLC T2 - InCom '96 T2 - InCom '96 - International Symposium on Instrumentalized Analytical Chemistry and Computer Technology CY - Düsseldorf, Deutschland DA - 1996-03-25 PY - 1996 PB - IAS CY - Moers AN - OPUS4-2213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Much, Helmut A1 - Schulz, Günter A1 - Spranger, K. T1 - Zur Charakterisierung von synthetischen Polymeren durch MALDI-TOF in Kopplung mit der LACCC T2 - Abstracts / Analytica Conference 96 T2 - Analytica Conference 96 CY - München, Deutschland DA - 1996-04-23 PY - 1996 PB - Messe München GmbH CY - München AN - OPUS4-2219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ramanathan, Thillaiyan A1 - Schulz, Eckhard A1 - Subramanian, K. T1 - Determination of energy release rate in carbon fiber - Thermoplastic composites and comparison of crack propagation in amorphous and crystalline interface by single fiber pullout test JF - Journal of reinforced plastics and composites N2 - The fracture toughness in the fiber-matrix composite by means of the single fiber pull-out test can be achievable, if it is possible to measure the compliance of partial debonded fiber, which necessitates a stable crack propagation and the determination of the corresponding crack length. A combination of high stiff test equipment and a simultaneous monitoring of the photo-elastic pattern of the embedded fibers with the help of polarization microscope enables to measure crack length and determination of Gc [Hampe, A and Marotzke, C. (1997). The Energy Release Rate of the Fiber/Polymer Matrix Interface: Measurement and Theoretical Analysis, J. Reinf. Plast. and Compo., 16: 341-352.]. This method is well-known for glass fiber-amorphous polymer composite. In this investigation, we tried to implement the same technique to C-fiber with amorphous and semi-crystalline polymer composites. The energy release rate (ERR) of the fiber-matrix interface was evaluated for the carbon fiber-reinforced in polycarbonate (PC) by interfacial crack propagation arising in the single fiber pullout test. Further, the crack propagation at the fiber-matrix interface with different matrix morphology was discussed with the use of photo-elastic pattern observed with the aid of polarization microscope. KW - Micromechanics KW - Carbon Fibers KW - Thermoplastic polymers KW - Fracture toughness PY - 2004 DO - https://doi.org/10.1177/0731684404039788 SN - 0731-6844 SN - 1530-7964 VL - 23 IS - 15 SP - 1639 EP - 1650 PB - Technomic Publ. Co. CY - Westport, Conn. AN - OPUS4-4486 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reinecke, K. A1 - Mischke, Wolf-Dietrich A1 - Ulrich, Armin A1 - Schulz-Forberg, Bernd T1 - Tankcontainer für gefährliche Güter im Unfallfeuer JF - Gefährliche Ladung PY - 1977 SN - 0016-5808 VL - 22 IS - 10 SP - 37 EP - 39 PB - Storck CY - Hamburg AN - OPUS4-8600 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulz, Eckhard A1 - Schulte, K. T1 - Fachausschuss "Gefüge und Eigenschaften von Polymerwerkstoffen" JF - Zeitschrift für Metallkunde N2 - Die in zunehmenden Maße Mitte der 80er Jahre einsetzende Substitution von metallischen Materialien z. B. durch hochleistungsfähige polymere Werkstoffe und Verbundwerkstoffe wurde u. a. von der DGM zum Anlass genommen, ihre zukünftigen Aufgaben neu zu definieren und gleichzeitig mit der Gründung des Fachausschusses "Gefüge und Eigenschaften von Polymerwerkstoffen" dieser neuen Entwicklung in der Materialkunde auf dem Gebiet der Kunststoffe und ihrer Anwendungen Rechnung zu tragen. KW - Aufgaben KW - Ziele PY - 2004 DO - https://doi.org/10.1515/ijmr-2004-0141 SN - 0044-3093 VL - 95 IS - 9 (85 Jahre DGM) SP - 742 EP - 743 PB - Hanser CY - München AN - OPUS4-5988 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -