TY - JOUR A1 - Brücher, M. A1 - von Bohlen, A. A1 - Jacob, P. A1 - Franzke, J. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Müller, Bernd R. A1 - Scharf, Oliver A1 - Hergenröder, R. T1 - The charge of solid-liquid interfaces measured by X-ray standing waves and streaming current N2 - Measurements of ion distributions at a charged solid–liquid interface using X-ray standing waves (XSW) are presented. High energy synchrotron radiation (17.48 keV) is used to produce an XSW pattern inside a thin water film on a silicon wafer. The liquid phase is an aqueous solution containing Br and Rb ions. The surface charge is adjusted by titration. Measurements are performed over a pH range from 2.2–9, using the native Si oxide layer and functional (amine) groups as surface charge. The Debye length, indicating the extension of the diffuse layer, could be measured with values varying between 1–4 nm. For functionalized wafers, the pH dependent change from attraction to repulsion of an ion species could be detected, indicating the isoelectric point. In combination with the measurement of the streaming current, the surface charge of the sample could be quantified. KW - Interfacial charge KW - Solid/liquid interfaces KW - Surface analysis KW - Surface functionalization KW - X-ray spectrometry KW - X-ray KW - Standing waves KW - XSW KW - Streaming current KW - Synchrotron radiation PY - 2010 DO - https://doi.org/10.1002/cphc.201000166 SN - 1439-4235 SN - 1439-7641 VL - 11 IS - 10 SP - 2118 EP - 2123 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-22057 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rodrigues, M. A1 - Schreiner, M. A1 - Mäder, M. A1 - Melcher, M. A1 - Guerra, M. A1 - Salomon, J. A1 - Radtke, Martin A1 - Alram, M. A1 - Schindel, N. T1 - The hoard of Becin - non-destructive analysis of the silver coins N2 - We report the results of an analytical investigation on 416 silver-copper coins stemming from the Ottoman Empire (end of 16th and beginning of 17th centuries), using synchrotron micro X-ray fluorescence analysis (SRXRF). In the past, analyses had already been conducted with energy dispersive X-ray fluorescence analysis (EDXRF), scanning electron microscopy with energy dispersive X-ray spectrometry (SEM/EDX) and proton induced X-ray emission spectroscopy (PIXE).With this combination of techniques it was possible to confirm the fineness of the coinage as well as to study the provenance of the alloy used for the coins. For the interpretation of the data statistical analysis (principal component analysis—PCA) has been performed. A definite local assignment was explored and significant clustering was obtained regarding the minor and trace elements composing the coin alloys. KW - SRXRF KW - Silber KW - Archaeometrie PY - 2010 DO - https://doi.org/10.1007/s00339-010-5627-y SN - 0947-8396 VL - 99 IS - 2 SP - 351 EP - 356 PB - Springer CY - Berlin AN - OPUS4-23170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Görner, Wolf A1 - Berger, Achim A1 - Merchel, Silke A1 - Pernicka, E. A1 - Radtke, Martin A1 - Reiche, I. A1 - Reinholz, Uwe A1 - Riederer, J. A1 - Riesemeier, Heinrich A1 - Wunderlich, C. H. T1 - Kunst- und Kulturgüter unter "Beschuss" T2 - Jahrestagung Zerstörungsfreie Materialprüfung 2004 CY - Salzburg, Österreich DA - 2004-05-17 KW - SY-RFA KW - PIXE KW - PIGE KW - PAA KW - Zerstörungsfreie Analyse KW - Silberstiftzeichnungen KW - Himmelsscheibe von Nebra KW - Indische Moghulmalereien PY - 2004 UR - http://www.ndt.net/article/dgzfp04/papers/p46/p46.htm SN - 3-931381-55-2 SP - 1(?) EP - 11(?) PB - DGZfP CY - Berlin AN - OPUS4-6897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wilde, L. A1 - Radnik, J. A1 - Schneider, M. A1 - Herein, D. A1 - Riesemeier, Heinrich A1 - Radtke, Martin T1 - In situ TEY cell for XAS measurements at the BAMline PY - 2004 UR - http://www.helmholtz-berlin.de/media/media/oea/web/pr_webseite/druckschriften/berichte/bessy/annualreport2003.pdf#page=283 SN - 0179-4159 SP - 283 EP - 285 PB - Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung CY - Berlin AN - OPUS4-3508 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Berger, Achim A1 - Görner, Wolf A1 - Merchel, Silke A1 - Radtke, Martin A1 - Riesemeier, Heinrich A1 - Reiche, I. A1 - Riederer, J. T1 - Non-destructive investigations of Dürer's silver point drawings by Sy-XRF PY - 2002 UR - http://www.helmholtz-berlin.de/media/media/oea/web/pr_webseite/druckschriften/berichte/bessy/annualreport2001.pdf#page=292 SN - 0179-4159 SP - 292 EP - 293 PB - Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung CY - Berlin AN - OPUS4-1324 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Berger, Achim A1 - Görner, Wolf A1 - Merchel, Silke A1 - Reiche, I. A1 - Riederer, J. A1 - Riesemeier, H. T1 - Spatial Resolved Trace Analysis of Dürer's Silver Point Drawings by Means of SR-XRF T2 - European Conference on Energy Dispersive X-Ray Spectrometry (EDXRS) CY - Berlin, Germany DA - 2002-06-16 PY - 2002 SP - 158 AN - OPUS4-1397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Berger, Achim A1 - Görner, Wolf A1 - Merchel, Silke A1 - Radtke, Martin A1 - Riesemeier, Heinrich A1 - Reiche, I. A1 - Riederer, J. T1 - A closer look at Albrecht Dürer's drawings (1471-1528) PY - 2002 UR - http://www.helmholtz-berlin.de/media/media/oea/web/pr_webseite/druckschriften/infos/bessy/highlights2001.pdf#page=32 SN - 0179-4159 SP - 32 EP - 33 PB - Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung CY - Berlin AN - OPUS4-1323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reiche, I. A1 - Berger, Achim A1 - Görner, Wolf A1 - Merchel, Silke A1 - Radtke, Martin A1 - Riederer, J. A1 - Riesemeier, Heinrich T1 - Silberstiftzeichnungen - Zerstörungsfreie Spurenanalyse mit Synchrotronstrahlung T2 - 10. IADA-Kongress (Internationale Arbeitsgemeinschaft der Archiv-, Bibliotheks- und Graphikrestauratoren) CY - Göttingen, Deutschland DA - 2003-09-21 PY - 2003 SN - 1563-2628 VL - 4 PB - Foto Text Verl. CY - Stuttgart AN - OPUS4-2663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kaiser, J. A1 - Szczerba, Wojciech A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Albrecht, M. A1 - Lu, Y. A1 - Ballauff, M. T1 - The structure of AuPd nanoalloys anchored on spherical polyelectrolyte brushes determined by x-ray absorption spectroscopy N2 - Well-defined and facetted bimetallic gold–palladium nanoalloys have been synthesized and anchored in spherical polyelectrolyte brushes (SPB) as composite particles (AuPd@SPB). These particles are better catalysts in aqueous phase than the pure metals. The atomistic arrangement of these nanoalloys has been analysed by extended X-ray absorption fine structure (EXAFS) spectroscopy at the Au–L3 and the Pd–K absorption edge. The samples with high amounts of gold appear as almost statistically mixed random alloys. Alloy compositions with less gold show slight enrichment of Pd at the surface of the particle. In addition, signals of non-metallic palladium appear at the Pd–K edge which indicate the presence of the Pd2+ species in addition to metallic palladium. The relation of these structural features to the catalytic activity is discussed. KW - EXAFS KW - Nanoalloys KW - Gold KW - Palladium KW - K-edge KW - L3-edge KW - HR-TEM KW - Synchrotron radiation KW - BAMline PY - 2013 DO - https://doi.org/10.1039/c3fd20132e SN - 1359-6640 SN - 1364-5498 VL - 162 SP - 45 EP - 55 PB - Soc. CY - Cambridge [u.a.] AN - OPUS4-28300 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rodrigues, M. A1 - Schreiner, M. A1 - Melcher, M. A1 - Guerra, M. A1 - Salomon, J. A1 - Radtke, Martin A1 - Alram, M. A1 - Schindel, N. T1 - Analysis of the hoard of Becin using X-ray-based techniques N2 - Four hundred and sixteen silver coins stemming from the Ottoman Empire (16th and 17th centuries) were analyzed to confirm the fineness of the coinage as well as to study the provenance of the alloy used for the coins. As most of the coins showed the typical green patina on their surfaces due to corrosion processes that have led to the depletion of copper in the near surface domains of the silver coins in comparison to their core composition, small samples had to be taken, embedded in synthetic resin, and cross sectioned to investigate the true-heart metal composition. µ-synchrotron micro X-ray fluorescence analysis and µ-proton-induced X-ray emission were applied to determine the silver contents as well as the minor and trace elements. The type of the alloy was investigated as well as if coins minted in different locations demonstrated homogeneous traits concerning the predominant impurities (Au and Bi), which could suggest a common ore. Finally, energy-dispersive microanalysis in a scanning electron microscope was applied to study the homogeneity/heterogeneity of the coins and the presence of surface enrichments and to explain differences between the µ-synchrotron micro X-ray fluorescence analysis and µ-proton-induced X-ray emission measurements concerning the main component. In general, the silver content of the analyzed specimen varies between 90 and 95%. These outcomes have not supported the historical interpretations, which predict that during the period studied, a debasement of approximately 44% of the silver content of the coins should have occurred. KW - SRXRF KW - Silber KW - BAMline PY - 2012 DO - https://doi.org/10.1002/xrs.2415 SN - 0049-8246 VL - 41 IS - 6 SP - 416 EP - 424 PB - Wiley CY - Chichester AN - OPUS4-27723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dippong, Martin A1 - Carl, Peter A1 - Lenz, C. A1 - Schenk, J. A. A1 - Hoffmann, Katrin A1 - Schwaar, Timm A1 - Schneider, Rudolf A1 - Kuhne, Maren T1 - Hapten-specific single-cell selection of hybridoma clones by fluorescence-activated cell sorting for the generation of monoclonal antibodies N2 - The conventional hybridoma screening and subcloning process is generally considered to be one of the most critical steps in hapten-specific antibody production. It is time-consuming, monoclonality is not guaranteed, and the number of clones that can be screened is limited. Our approach employs a novel hapten-specific labeling technique of hybridoma cells. This allows for fluorescence-activated cell sorting (FACS) and single-cell deposition and thereby eliminates the above-mentioned problems. A two-step staining approach is used to detect antigen specificity and antibody expression: in order to detect antigen specificity, hybridoma cells are incubated with a hapten−horseradish peroxidase conjugate (hapten−HRP), which is subsequently incubated with a fluorophore-labeled polyclonal anti-peroxidase antibody (anti-HRP−Alexa Fluor 488). To characterize the expression of membrane-bound immunoglobulin G (IgG), a fluorophore-labeled anti-mouse IgG antibody (anti-IgG−Alexa Fluor 647) is used. Hundreds of labeled hybridoma cells producing monoclonal antibodies (mAbs) specific for a hapten were rapidly isolated and deposited from a fusion mixture as single-cell clones via FACS. Enzyme-linked immunosorbent assay (ELISA) measurements of the supernatants of the sorted hybridoma clones revealed that all hapten-specific hybridoma clones secrete antibodies against the target. There are significant improvements using this high-throughput technique for the generation of mAbs including increased yield of antibody-producing hybridoma clones, ensured monoclonality of sorted cells, and reduced development times. KW - Monoclonal antibodies KW - FACS KW - Hybridoma cells PY - 2017 DO - https://doi.org/10.1021/acs.analchem.6b04569 SN - 0003-2700 SN - 1520-6882 VL - 89 IS - 7 SP - 4007 EP - 4012 PB - ACS Publications AN - OPUS4-40320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fortes Martin, R. A1 - Thünemann, Andreas A1 - Stockmann, Jörg M. A1 - Radnik, Jörg A1 - Koetz, J. T1 - From Nanoparticle Heteroclusters to Filament Networks by Self-Assembly at the Water–Oil Interface of Reverse Microemulsions N2 - Surface self-assembly of spherical nanoparticles of sizes below 10 nm into hierarchical heterostructures is under arising development despite the inherent difficulties of obtaining complex ordering patterns on a larger scale. Due to template-mediated interactions between oil-dispersible superparamagnetic nanoparticles (MNPs) and polyethylenimine-stabilized gold nanoparticles (Au(PEI)NPs) at the water–oil interface of microemulsions, complex nanostructured films can be formed. Characterization of the reverse microemulsion phase by UV–vis absorption revealed the formation of heteroclusters from Winsor type II phases (WPII) using Aerosol-OT (AOT) as the surfactant. SAXS measurements verify the mechanism of initial nanoparticle clustering in defined dimensions. XPS suggested an influence of AOT at the MNP surface. Further, cryo-SEM and TEM visualization demonstrated the elongation of the reverse microemulsions into cylindrical, wormlike structures, which subsequently build up larger nanoparticle superstructure arrangements. Such WPII phases are thus proven to be a new form of soft template, mediating the self-assembly of different nanoparticles in hierarchical network-like filaments over a substrate during solvent evaporation. KW - Small-angle X-ray scattering KW - SAXS KW - Nanoparticle KW - Nano structure PY - 2021 DO - https://doi.org/10.1021/acs.langmuir.1c01348 VL - 37 IS - 29 SP - 8876 EP - 8885 PB - American Chemical Society AN - OPUS4-53034 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bornemann-Pfeiffer, Martin A1 - Meyer, Klas A1 - Lademann, J. A1 - Kraume, M. A1 - Maiwald, Michael T1 - Contributions towards variable temperature shielding for compact NMR instruments N2 - The application of compact NMR instruments to hot flowing samples or exothermically reacting mixtures is limited by the temperature sensitivity of permanent magnets. Typically, such temperature effects directly influence the achievable magnetic field homogeneity and hence measurement quality. The internal-temperature control loop of the magnet and instruments is not designed for such temperature compensation. Passive insulation is restricted by the small dimensions within the magnet borehole. Here, we present a design approach for active heat shielding with the aim of variable temperature control of NMR samples for benchtop NMR instruments using a compressed airstream which is variable in flow and temperature. Based on the system identification and surface temperature measurements through thermography, a model predictive control was set up to minimise any disturbance effect on the permanent magnet from the probe or sample temperature. This methodology will facilitate the application of variable-temperature shielding and, therefore, extend the application of compact NMR instruments to flowing sample temperatures that differ from the magnet temperature. KW - Benchtop NMR KW - Continuous Processes KW - Inline Analytics KW - Model Predictive Control KW - Process Analytical Tecnology KW - Temperature Control PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579219 DO - https://doi.org/10.1002/mrc.5379 SN - 1097-458X SP - 1 EP - 10 PB - John Wiley & Sons Ltd. AN - OPUS4-57921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lilensten, L. A1 - Provost, K. A1 - Perrière, L. A1 - Fonda, E. A1 - Couzinié, J. A1 - Amman, F. A1 - Radtke, Martin A1 - Dirras, G. A1 - Guillot, I. T1 - Experimental investigation of the local environment and lattice distortion in refractory medium entropy alloys N2 - EXAFS analysis of pure elements, binary and ternary equiatomic refractory alloys within the Nb-Zr-Ti-Hf- Ta system is performed at the Nb and Zr K-edges to analyze the evolution of the chemical local environ- ment and the lattice distortion. A good mixing of the elements is found at the atomic scale. For some compounds, a distribution of distances between the central atom and its neighbors suggests a distortion of the structure. Finally, analysis of the Debye-Waller parameters shows some correlation with the lat- tice distortion parameter δ², and allows to quantify experimentally the static disorder in medium entropy alloys. KW - BAMline KW - Refractory alloys KW - EXAFS KW - Debye-Waller parameter PY - 2022 DO - https://doi.org/10.1016/j.scriptamat.2022.114532 SN - 1359-6462 VL - 211 SP - 1 EP - 6 PB - Elsevier Ltd. AN - OPUS4-55287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Margreiter, R. A1 - Baumann, J. A1 - Mantouvalou, I. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Strub, E. T1 - Investigations on fire-gilding N2 - Fire-gilding is a historic technique for the application of golden layers on a number of different base materials utilizing a gold amalgam. This technique leaves a significant amount of Hg in the golden layer, giving archeometrists a reliable indicator to identify firegildings. Recent findings on presumably fire-gilded objects have shown in several cases significantly lower Hg content than previously studied objects. This prompted a synchrotron-based X-ray fluorescence investigation into the Hg distribution along the material–gilding interface, as well as a series of measurements regarding the Hg content development in fire-gilded samples during artificial aging. This work presents findings on laboratory-prepared fire-gildings, indicating an Hg enrichment at the interface of firegilded silver samples. Notably, such an enrichment is missing in fire-gilded copper samples. Further, it is confirmed that fire-gilded layers typically do not undercut an Hg bulk content of 5%. In this light, it seems improbable that ancient samples that contain <5% Hg are fire-gilded. The results presented in this study might lead to a non-destructive method to identify the Hg enrichment at the interface. This might be obtained by a combination of different non-destructive measurements and might also work unambiguously in samples in which the gold top layer is altered. KW - BAMline KW - X-Ray Fluorescence KW - Gilding KW - Depth profile KW - Archaeometry PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-552885 DO - https://doi.org/10.1111/arcm.12797 SN - 0003-813X SP - 1 EP - 14 PB - Wiley online library AN - OPUS4-55288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lenz, J. U. A1 - Pospiech, D. A1 - Komber, H. A1 - Korwitz, A. A1 - Kobsch, O. A1 - Paven, M. A1 - Albach, R. W. A1 - Günther, Martin A1 - Schartel, Bernhard T1 - Effective halogen-free flame-retardant additives for crosslinked rigid polyisocyanurate foams: Comparison of chemical structures N2 - The impact of phosphorus-containing flame retardants (FR) on rigid polyisocyanurate (PIR) foams is studied by systematic variation of the chemical structure of the FR, including non-NCO-reactive and NCO-reactive dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide (BPPO)- and 9,10 dihydro-9-oxa-10 phosphaphenanthrene-10-oxide (DOPO)-containing compounds, among them a number of compounds not reported so far. These PIR foams are compared with PIR foams without FR and with standard FRs with respect to foam properties, thermal decomposition, and fire behavior. Although BPPO and DOPO differ by just one oxygen atom, the impact on the FR properties is very significant: when the FR is a filler or a dangling (dead) end in the PIR polymer network, DOPO is more effective than BPPO. When the FR is a subunit of a diol and it is fully incorporated in the PIR network, BPPO delivers superior results. KW - Flame retardant; KW - Dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide; BPPO KW - 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide; DOPO KW - Polyisocyanurate; PIR KW - Rigid foam KW - Cone calorimeter KW - Pudovik reaction PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567712 DO - https://doi.org/10.3390/ma16010172 SN - 1996-1944 VL - 16 IS - 1 SP - 1 EP - 22 PB - MDPI CY - Basel AN - OPUS4-56771 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Emamverdi, Farnaz A1 - Yin, Huajie A1 - Smales, Glen Jacob A1 - Harrison, W. J. A1 - Budd, P. M. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Polymers of intrinsic microporosity - Molecular mobility and physical aging revisited by dielectric spectroscopy and X‑ray scattering N2 - Polymers of intrinsic microporosity (PIMs) are promising candidates for the active layer in gas separation membranes due to their high permeability and reasonable permselectivity. These appealing properties originate from a microporous structure as a result of inefficient segment packing in the condensed state due to a combination of a ladder-like rigid backbone and sites of contortion. However, this class of polymers suffers from a significant decrease in the permeability with time due to physical aging, whereby typically, the permselectivity increases. The initial microporous structures approach a denser state via local rearrangements, leading to the reduction of the permeability. Hence, a detailed characterization of the molecular mobility in such materials can provide valuable information on physical aging. In this work, the dielectric behavior of PIM-1 films and their behavior upon heating (aging) were revisited by isothermal frequency scans during different heating/cooling cycles over a broad temperature range between 133 and 523 K (−140 to 250 °C). In addition, the obtained results were compared with data of samples that were annealed at ambient temperatures over different time scales. Multiple dielectric processes were observed: several relaxation processes due to local fluctuations and a Maxwell−Wagner−Sillars polarization effect related to the microporosity. The temperature dependence of the rates of all processes follows the Arrhenius law where the estimated activation energy depends on the nature of the process. The influence of the thermal history (aging) on the processes is discussed in detail. KW - Polymers of intrinsic microporosity PY - 2022 DO - https://doi.org/10.1021/acs.macromol.2c00934 VL - 55 SP - 7340 EP - 7350 PB - American Chemical Society CY - Washington, DC AN - OPUS4-55485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zoega, A. A1 - Krause, Martin A1 - Kurz, J. A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Boßmann, N. T1 - Ultraschalluntersuchungen zur Rissdetektion an Spannbetonschwellen N2 - Im deutschen Eisenbahnnetz sind ca. 80 Millionen Spannbetonschwellen verbaut. Analog zu anderen Bauwerken werden Wpannbetonschwellen regelmäßig visuell inspiziert. Die Rissbildung ist bei diesen Inspektionen ein Kriterium für die Schädigung einer Spannbetonschwelle. Durch Rissbildung kann es passieren, dass Betonschwellen ihre Nutzungsdauer nicht erreichen. KW - ZfPBau KW - Spannbeton PY - 2017 VL - März 2017 IS - Ernst & Sohn Special 2017 SP - 20 EP - 22 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-48112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lenz, J. A1 - Pospiech, D. A1 - Paven, M. A1 - Albach, R. W. A1 - Günther, Martin A1 - Schartel, Bernhard A1 - Voit, B. T1 - Improving the Flame Retardance of Polyisocyanurate Foams by Dibenzo[d,f][1,3,2]dioxaphosphepine 6-Oxide-Containing Additives N2 - A series of new flame retardants (FR) based on dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide (BPPO) incorporating acrylates and benzoquinone were developed previously. In this study, we examine the fire behavior of the new flame retardants in polyisocyanurate (PIR) foams. The foam characteristics, thermal decomposition, and fire behavior are investigated. The fire properties of the foams containing BPPO-based derivatives were found to depend on the chemical structure of the substituents. We also compare our results to state-of-the-art non-halogenated FR such as triphenylphosphate and chemically similar phosphinate, i.e. 9,10-dihydro-9-oxa-10- phosphaphenanthrene-10-oxide (DOPO), based derivatives to discuss the role of the phosphorus oxidation state. KW - Polyisocyanurate KW - Dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide KW - Phospha-Michael addition KW - Flame retardant KW - Foams PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-485590 DO - https://doi.org/10.3390/polym11081242 SN - 2073-4360 VL - 11 IS - 8 SP - Article 1242 PB - MDPI AN - OPUS4-48559 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Patrick P. A1 - Kohlhoff, Harald A1 - Hüllmann, Dino A1 - Krentel, Daniel A1 - Kluge, Martin A1 - Dzierliński, M. A1 - Lilienthal, A. J. A1 - Bartholmai, Matthias T1 - Aerial-based gas tomography – from single beams to complex gas distributions N2 - In this paper, we present and validate the concept of an autonomous aerial robot to reconstruct tomographic 2D slices of gas plumes in outdoor environments. Our platform, the so-called Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), combines a lightweight Tunable Diode Laser Absorption Spectroscopy (TDLAS) gas sensor with a 3-axis aerial stabilization gimbal for aiming at a versatile octocopter. While the TDLAS sensor provides integral gas concentration measurements, it does not measure the distance traveled by the laser diode’s beam nor the distribution of gas along the optical path. Thus, we complement the set-up with a laser rangefinder and apply principles of Computed Tomography (CT) to create a model of the spatial gas distribution from a set of integral concentration measurements. To allow for a fundamental ground truth evaluation of the applied gas tomography algorithm, we set up a unique outdoor test environment based on two 3D ultrasonic anemometers and a distributed array of 10 infrared gas transmitters. We present results showing its performance characteristics and 2D plume reconstruction capabilities under realistic conditions. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO). KW - Aerial robot olfaction KW - Mobile robot olfaction KW - Gas tomography KW - TDLAS KW - Plume PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-487843 DO - https://doi.org/10.1080/22797254.2019.1640078 SP - 1 EP - 16 PB - Taylor & Francis CY - London AN - OPUS4-48784 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Martin A1 - Wu, D. A1 - Berghmans, J. T1 - Spontaneous ignition behaviour of coal dust accumulations: A comparison of extrapolation methods from lab-scale to industrial-scale N2 - Smouldering fires and explosions arising from self-ignition of coal dust deposits represent a serious hazard for human being, environment and industry. It is essential for plant operators to know the conditions (temperature, duration and quantity) at which storage will be safe. In this work, self-ignition behaviour of three bituminous coal dusts in large scales are theoretically studied, based on the experimental data via a standardized hot-basket apparatus. A comprehensive 2-D transient model is developed, using a 2nd-order reaction kinetics considering both coal and oxygen consumptions, to investigate self-ignition parameters of coal dust accumulations. The numerical model shows a less conservative prediction compared with the steady-state methods. The computational self-ignition temperature and ignition delay time show a satisfaction agreement with lab-scale experimental results. In addition, the influences of ambient temperature and moisture content are analysed. The result shows that the moisture content delays the ignition and a small variation of the ambient temperature nearby the critical condition will lead to a large difference of the ignition delay time. KW - Spontanious ignition KW - Self-ignition KW - Extrapolation methods PY - 2019 DO - https://doi.org/10.1016/j.proci.2018.05.140 SN - 1540-7489 VL - 37 IS - 3 SP - 4181 EP - 4191 PB - Elsevier AN - OPUS4-47291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - De Samber, B. A1 - Scharf, Oliver A1 - Buzanich, Günter A1 - Garrevoet, J. A1 - Tack, P. A1 - Radtke, Martin A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Evens, R. A1 - De Schamphelaere, K. A1 - Falkenberg, G. A1 - Janssen, C. A1 - Vincze, L. T1 - Three-dimensional X-ray fluorescence imaging modes for biological specimens using a full-field energy dispersive CCD camera N2 - Besides conventional scanning X-ray fluorescence imaging at synchrotron sources, full-field X-ray fluorescence (FF-XRF) imaging techniques that do not implicitly require spatial scanning of the sample have become available. FF-XRF has become achievable thanks to the development of a new type of energy dispersive CCD-based 2D detector, also referred to as a 'color X-ray camera (CXC)' or 'SLcam'. We report on different imaging schemes for biological samples using FF-XRF imaging: (a) 2D 'zoom' imaging with pinhole optics using the 'camera obscura' principle; (b) 2D 'fixed magnification' imaging using magnifying polycapillary optics; and (c) 3D-FF-XRF imaging using an X-ray sheet beam or computed tomography (CT). The different FF-XRF imaging modes are illustrated using the crustacean Daphnia magna, a model organism for investigating the effects of metals on organism/ecosystem health, and foraminifera, a class of amoeboid protist. Detailed analytical characterization of the set-up is performed through analyzing various reference materials in order to determine limits of detection (LODs) and sensitivities. Experiments were performed using the BAMline at the BESSY synchrotron (Berlin, Germany) and using the P06 Hard X-ray Microprobe at the PETRAIII synchrotron (Hamburg, Germany). KW - CXC KW - BAMline KW - Maia detector KW - Synchrotron PY - 2019 DO - https://doi.org/10.1039/c9ja00198k VL - 34 IS - 10 SP - 2083 EP - 2093 PB - Royal Society of Chemistry CY - Cambridge, United Kingdom AN - OPUS4-49359 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Colla, Camilla A1 - Krause, Martin A1 - Maierhofer, Christiane A1 - Höhberger, H.-J. A1 - Sommer, H. T1 - Combination of NDT techniques for site investigation of non-ballasted railway tracks N2 - Today's civil engineering NDT needs are for quantitative, fast to apply and easy to interpret methods. They are required on site both for evaluation of existing structures/infrastructure and for quality control in new construction. With this purpose, BAM has carried out in-situ feasibility studies, using radar, impact-echo and ultrasonic-echo methods. Two examples are given of their combined application on different railway slab–track constructions, using high frequency radar, scanning impact-echo and ultrasonic array methods. The aim was to evaluate limitations and advantages, comparability and complementarity of these methods. The on-site measurements demonstrated the possibility to investigate, with good accuracy via NDT, the bonding conditions between sleepers and slab, to locate voids and measure layer thickness. The acoustic and electromagnetic methods used, were found to be complementary. KW - Concrete KW - NDT KW - Impact echo KW - Ultrasonics KW - Radar KW - Railway PY - 2002 DO - https://doi.org/10.1016/S0963-8695(01)00033-0 SN - 0963-8695 VL - 35 SP - 95 EP - 105 PB - Butterworth-Heinemann CY - Oxford AN - OPUS4-1858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mero, M. A1 - Clapp, B. A1 - Jasapara, J.C. A1 - Rudolph, W. A1 - Ristau, D. A1 - Starke, K. A1 - Krüger, Jörg A1 - Martin, Sven A1 - Kautek, Wolfgang T1 - On the damage behavior of dielectric films when illuminated with multiple femtosecond laser pulses N2 - The physical effects reducing the damage threshold of dielectric films when exposed to multiple femtosecond pulses are investigated. The measured temperature increase of a Ta2O5 film scales exponentially with the pulse fluence. A polarized luminescence signal is observed that depends quadratically on the pulse fluence and is attributed to twophoton excitation of self-trapped excitons that form after band-to-band excitation. The damage fluence decreases with increasing pulse number, but is independent of the repetition rate from 1 Hz to 1 kHz at a constant pulse number. The repetition rate dependence of the breakdown threshold is also measured for TiO2 , HfO2, Al2O3, and SiO2 films. A theoretical model is presented that explains these findings. KW - Laser-induced damage KW - Laser materials KW - Ultrafast phenomena KW - Coatings PY - 2005 DO - https://doi.org/10.1117/1.1905343 SN - 0892-354X VL - 44 IS - 5 SP - 051107-1-051107-7 PB - Dekker CY - New York, NY AN - OPUS4-7406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bothe, Martin A1 - Mya, K.Y. A1 - Lin, E.M.J. A1 - Yeo, C. C. A1 - Lu, X. A1 - He, C. A1 - Pretsch, Thorsten T1 - Triple-shape properties of star-shaped POSS-polycaprolactone polyurethane networks N2 - Here, we present an investigation of the triple-shape properties of star-shaped polyhedral oligomeric silsesquioxane-poly(ε-caprolactone) polyurethanes (SPOSS-PUs), which have three-dimensional network structures. In a typical 'triple-shape functionalization process', mostly consisting of two tensile deformations at different temperatures, chain immobilization of the polymer network component poly(ε-caprolactone) (PCL) was successfully realized first through crystallization and then through vitrification. Subsequently, large parts of the respective strains were released under stress-free recovery conditions. The two-fold fixed ('programmed') specimens responded to heating with two independent length contractions (switching steps); the first shape change was associated with PCL devitrification and the second one with the melting of hitherto crystalline PCL. It was revealed that the triple-shape properties of SPOSS-PU networks considerably depend on PCL network chain length. When applying exactly the same 'triple-shape creation procedure', larger strain releases were detected in the first transition for polymers with a higher PCL network chain length, whereas the second transition was more accentuated for SPOSS-PU networks with a shorter PCL chain length. In the course of thermo-mechanical cycling, the formation of a neck during the second tensile deformation was repeatedly detected for SPOSS-PUs with higher PCL network chain length; in the subsequent recovery process the specimens even exhibited the highest total strain recoverability. Finally, gradual strain release could be achieved at temperatures below the PCL melting transition through the selection of up to four temperature holding steps, at which every time stable shapes were formed. KW - Shape memory polymer KW - Active polymer KW - Triple-shape polymer KW - Hybrid star-shaped polymer KW - POSS-polycaprolactone polyurethanes KW - Thermo-mechanical properties PY - 2012 DO - https://doi.org/10.1039/c1sm06474f SN - 1744-683X VL - 8 IS - 4 SP - 965 EP - 972 PB - RSC Publ. CY - Cambridge AN - OPUS4-25260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Haardt, P. A1 - Krause, Martin A1 - Streicher, Doreen A1 - Krause, H.-J. ED - Watanabe, E. ED - Frangopol, D. T1 - Scanning NDT-Methods for the Inspection of Highway Structures T2 - 2nd International Conference on Bridge Maintenance, Safety and Management CY - Kyoto, Japan DA - 2004-10-19 KW - ZfPBau KW - Ingenieurbauwerke KW - Automatisierung KW - Laserscanner KW - Ultraschallecho KW - Impuls Radar KW - Impact-Echo PY - 2004 SN - 90-5809-680-7 SP - 8 pages PB - Balkema CY - Leiden AN - OPUS4-5201 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mayer, K. A1 - Langenberg, K.-J. A1 - Krause, Martin A1 - Milmann, Boris A1 - Mielentz, Frank T1 - Characterization of reflector types by phase-sensitive ultrasonic data processing and imaging N2 - Ultrasonic and radar imaging techniques are limited in resolution by the wavelength in the material, yet information beyond those limits is hidden in complex frequency dependent reflection coefficients. The analysis of the phase of complex reflection coefficients together with the properties of imaging algorithms can help to characterize and to classify indications of defects in concrete buildings. This paper describes a method to extract phase information from measurements and SAFT reconstructed images. The influencing factors like material properties, transducer characteristics, and imaging algorithms based on Born or Physical Optics approximations are elaborated. Simulated and experimental results are briefly discussed. KW - NDT KW - Imaging KW - Flaw characterization KW - Tendon ducts KW - Phase analysis KW - Ultrasonic echo KW - SAFT KW - FT-SAFT KW - EFIT-modeling KW - Modellierung KW - EFIT KW - Spannbeton KW - Ultraschallecho KW - Spannkanäle KW - Verpressfehler KW - Zerstörungsfreie Prüfung im Bauwesen KW - ZfP-Bau PY - 2008 DO - https://doi.org/10.1007/s10921-008-0035-3 SN - 0195-9298 SN - 1573-4862 VL - 27 IS - 1-3 SP - 35 EP - 45 PB - Plenum Press CY - New York, NY AN - OPUS4-17926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, Martin A1 - Milmann, Boris A1 - Mielentz, Frank A1 - Streicher, Doreen A1 - Redmer, Bernhard A1 - Mayer, K. A1 - Langenberg, K.-J. A1 - Schickert, M. T1 - Ultrasonic Imaging Methods for Investigation of Post-tensioned Concrete Structures: A Study of Interfaces at Artificial Grouting Faults and Its Verification N2 - This paper presents the progress of successful location of grouting faults in tendon ducts with ultrasonic imaging. The examples were obtained in the research group FOR 384 funded by DFG (German Research Foundation). The co-operation of experimental research and modeling allowed imaging and identification of grouted and ungrouted areas of tendon ducts (including strands) in a large test specimen (40 m²). In addition to the criteria for indicating grouting faults in post-tensioned ducts known until now the phase evaluation of reflected ultrasonic pulses is described. Experiments and modeling of wave propagation are presented for reflections at metal plates in concrete (thickness range 0.5 mm to 40 mm) and for tendon ducts including strands. The main part of the progress was achieved by automated measurements using dry contact transducers, 3D-SAFT reconstruction including phase evaluation and modeling considering wave propagation for typical elastic parameters and exact experimental site conditions. The results for shear waves as well as for pressure waves are compared in the frequency range from 50 kHz to 120 kHz. KW - Non-destructive testing KW - Tendons KW - Prestressed concrete bridges KW - Ultrasonic echo KW - Reconstruction calculation KW - 3D-SAFT KW - Modeling (EFIT) PY - 2008 DO - https://doi.org/10.1007/s10921-008-0033-5 SN - 0195-9298 SN - 1573-4862 VL - 27 IS - 1-3 SP - 67 EP - 82 PB - Plenum Press CY - New York, NY AN - OPUS4-17922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mayer, K. A1 - Langenberg, K.-J. A1 - Krause, Martin A1 - Maierhofer, Christiane A1 - Milmann, Boris A1 - Kohl, Christoph T1 - Characterization of ultrasonic and radar reflector types in concrete by phase evaluation of the signal and the reconstructed image T2 - 9th European Conference on NDT CY - Berlin, Germany DA - 2006-09-25 KW - NDT-CE KW - Ultrasonic echo KW - Radar KW - Phase evaluation KW - Modeling of wave propagation KW - Reconstruction calculation PY - 2006 SN - 3-931381-86-2 SP - 1 EP - 8(?) PB - European Federation for Non-Destructive Testing CY - Berlin AN - OPUS4-14225 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kroggel, O. A1 - Krause, Martin A1 - Schickert, M. A1 - Langenberg, K.-J. T1 - Moderne Verfahren der Bauwerksdiagnose, Entwicklung und Anwendung - Die DFG-Forschergruppe FOR384 stellt ihre Ergebnisse vor - Ultraschall T2 - Fachtagung 2005 des Deutschen Ausschusses für Stahlbeton in Zusammenarbeit mit der Bundesanstalt für Materialforschung und -prüfung "Zerstörungsfreie Prüfverfahren und Bauwerksdiagnose im Betonbau" CY - Berlin, Deutschland DA - 2005-03-10 KW - Ultraschallecho-Verfahren KW - Beton KW - Fundamente KW - Erhärtungsverhalten KW - Tomographie PY - 2005 SP - A5 EP - A10 PB - BAM CY - Berlin AN - OPUS4-11718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reifschneider, O. A1 - Vennemann, A. A1 - Buzanich, Günter A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Hogeback, J A1 - Köppen, C. A1 - Großgarten, M. A1 - Sperling, M. A1 - Wiemann, M. A1 - Karst, U. T1 - Revealing Silver Nanoparticle Uptake by Macrophages Using SR-μXRF and LA-ICP-MS N2 - To better study the impact of nanoparticles on both in vitro and in vivo models, tissue distribution and cellular doses need to be described more closely. Here silver nanoparticles were visualized in alveolar macrophages by means of synchrotron radiation micro X-ray fluorescence spectroscopy (SR-μXRF) with high spatial resolution of 3 × 3 μm2. For the spatial allocation of silver signals to cells and tissue structures, additional elemental labeling was carried out by staining with eosin, which binds to protein and can be detected as bromine signal with SR-μXRF. The method was compatible with immunostaining of macrophage antigens. We found that the silver distribution obtained with SR-μXRF was largely congruent with distribution maps from a subsequent laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) of the same tissue sites. The study shows a predominant, though not exclusive uptake of silver into alveolar macrophages in the rat lung, which can be modeled by a similar uptake in cultured alveolar macrophages. Advantages and limitations of the different strategies for measuring nanoparticle uptake at the single cell level are discussed. KW - Synchrotron KW - BAMline KW - XRF KW - Nanoparticle KW - Macrophagen PY - 2020 DO - https://doi.org/10.1021/acs.chemrestox.9b00507 VL - 33 IS - 5 SP - 1250 EP - 1255 PB - American Chemical Society AN - OPUS4-50855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konnertz, Nora A1 - Ding, Yi A1 - Harrison, W.J. A1 - Budd, P.M. A1 - Schönhals, Andreas A1 - Böhning, Martin T1 - Molecular mobility of the high performance membrane polymer PIM-1 as investigated by dielectric spectroscopy N2 - The increasing demand for energy efficient separation processes fosters the development of new high performance polymers as selective separation layers for membranes. PIM-1 is the archetypal representative of the class of polymers of intrinsic microporosity (PIM) which are considered most promising in this sector, especially for gas separations. Since their introduction, PIMs stimulated a vast amount of research in this field and meanwhile evolved to the state of the art in membrane technology for gas separation. The major obstacle for extending the practical membrane application is their strong tendency to physical aging. For the first time, investigations by broadband dielectric spectroscopy (BDS) addressing molecular dynamics and conductivity in PIM 1 are presented. As chain packing during film formation from the casting solution and physical aging are key factors determining the separation performance of PIMs as membrane materials, characterization of the molecular mobility in such materials as revealed by BDS will provide valuable information for further development and optimization. KW - PIM-1 KW - BDS broadband dielectric spectroscopy KW - Relaxation KW - Membrane PY - 2016 DO - https://doi.org/10.1021/acsmacrolett.6b00209 SN - 2161-1653 VL - 5 IS - 4 SP - 528 EP - 532 PB - ACS American Chemical Society CY - Washington, DC, USA AN - OPUS4-35798 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Kurz, J.H. A1 - Lanata, F. A1 - Krstevska, L. A1 - Cavalli, A. T1 - Needs for further developing monitoring- and NDT-methods for timber structures N2 - For the assessmentand for monitoring of timber structures there are numerous promising methods that enable the quantitative description of the current condition of construction elements or parts of a structure. This concerns material properties like modulus of elasticity, moisture content and density as well as structural properties like dynamic characteristics, localization of inhomogeneities, cracks, and biological attack. During the work in COST Action FP 1101, since 2012 the capability of experimental methods are discussed and compared. This covers electrical and electromagnetic wave methods (resistivity, microwave, Radar, X-Ray), elastic waves (ultrasound, pile testing) and mechanical testing (static and dynamic). Describing and collecting the use of the experimental methods for monitoring purposes was the objective of working group 3 "Monitoring of Timber Structures" of the COST Action. Monitoring capabilities will extend the use of timber structures to further applications in civil engineering. So far, no standard exists but collections of application examples and review papers representing the state of the art. From there needs for further developments regarding monitoring and NDT methods for timber structures can be identified and these are described in this paper. T2 - SHATIS 2015 - 3rd International conference on structural health assessment of timber structures CY - Wroclaw, Poland DA - 09.09.2015 KW - Holz Konstruktionen KW - Monitoring KW - Langzeitverhalten KW - Erdbebensicherheit KW - Historische Bauwerke KW - Ultrasonic echo imaging KW - Historical timber structures KW - Seismic investigation KW - Dynamic tests KW - Anisotropic wave propagation KW - Extending service life PY - 2015 VL - 1 SP - 1 EP - 12 AN - OPUS4-35178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gardei, André A1 - Garcia, O. A1 - Riedl, Martin A1 - Vanhellemond, I. A1 - Suput, J.S. A1 - Santarelli, M.-L. A1 - Rodríguez-Maribona, I. A1 - Müller, Urs ED - Jadwiga W. Lukaszewicz, ED - Piotr Niemcewicz, T1 - Performance and durability of a new antigraffiti system for cultural heritage - the EC project GRAFFITAGE T2 - 11th International Congress on Deterioration and Conservation of Stone CY - Torun, Poland DA - 2008-09-15 KW - Cultural heritage KW - Antigraffiti system KW - Sandstone KW - Limestone KW - Brick KW - Monument KW - Cleaning KW - Historische Baustoffe PY - 2008 SN - 978-83-231-2237-1 VL - II SP - 889 EP - 897 PB - Nicolaus Copernicus University Press CY - Torun, Poland AN - OPUS4-18844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mayer, K. A1 - Chinta, P.K. A1 - Langenberg, K.-J. A1 - Krause, Martin T1 - Ultrasonic imaging of defects in known anisotropic and inmomogeneous structures with fast synthetic aperture methodes T2 - 18th WCNDT - World conference on nondestructive testing CY - Durban, South Africa DA - 2012-04-16 KW - SAFT KW - Pulse echo technique KW - Back propagation KW - Inverse scattering KW - Imaging PY - 2012 SN - 978-0-620-52872-6 SP - 1 EP - 20 AN - OPUS4-35101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballier, G. A1 - Mayer, K. A1 - Langenberg, K.-J. A1 - Schulze, Sebastian A1 - Krause, Martin T1 - Improvement on tendon duct examination by modelling and imaging with synthetic aperture and one-way inverse methods T2 - 18th WCNDT - World conference on nondestructive testing CY - Durban, South Africa DA - 2012-04-16 KW - SAFT KW - Ultrasonic NDT KW - Concrete KW - One way KW - AFIT KW - Time reversal PY - 2012 SN - 978-0-620-52872-6 SP - 1 EP - 8 AN - OPUS4-35102 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konnertz, Nora A1 - Ding, Yi A1 - Harrison, W.J. A1 - Budd, P.M. A1 - Schönhals, Andreas A1 - Böhning, Martin T1 - Molecular mobility and gas transport properties of nanocomposites based on PIM-1 and polyhedral oligomeric phenethyl-silsesquioxanes (POSS) N2 - Polymers with intrinsic microporosity (PIMs) are of great interest in the field of gas separation membranes. Already the first synthesized PIM-1 shows extraordinary permeability and selectivity. Unfortunately, PIM-1 is susceptible to physical aging and thus gradually loses its outstanding properties. In this study a polyhedral oligomeric silsesquioxane with phenethyl substituents (PhenethylPOSS) was used as a nanofiller (0–40 wt%) in the PIM-1 matrix to potentially improve the gas transport properties and prevent physical aging. The molecular mobility of the solution-cast nanocomposite films was analyzed by Broadband Dielectric Spectroscopy (BDS). Furthermore, gas permeability was determined with the time lag method (0–20 bar upstream pressure) at 35 °C for N2, O2, CH4 and CO2. KW - Broadband Dielectric Spectroscopy KW - Gas separation KW - Gas permeation KW - Polymers of intrinsic microporosity KW - Nanocomposite KW - POSS KW - PIM-1 PY - 2017 DO - https://doi.org/10.1016/j.memsci.2017.02.007 SN - 0376-7388 SN - 1873-3123 VL - 529 SP - 274 EP - 285 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-39169 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Kohlhoff, Harald A1 - Hüllmann, Dino A1 - Lilienthal, A.J. A1 - Kluge, Martin T1 - Bringing Mobile Robot Olfaction to the Next Dimension – UAV-based Remote Sensing of Gas Clouds and Source Localization N2 - This paper introduces a novel robotic platform for aerial remote gas sensing. Spectroscopic measurement methods for remote sensing of selected gases lend themselves for use on mini-copters, which offer a number of advantages for inspection and surveillance. No direct contact with the target gas is needed and thus the influence of the aerial platform on the measured gas plume can be kept to a minimum. This allows to overcome one of the major issues with gas-sensitive mini-copters. On the other hand, remote gas sensors, most prominently Tunable Diode Laser Absorption Spectroscopy (TDLAS) sensors have been too bulky given the payload and energy restrictions of mini-copters. Here, we introduce and present the Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), which combines a novel lightweight TDLAS sensor with a 3-axis aerial stabilization gimbal for aiming on a versatile hexacopter. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO). It enables tomographic reconstruction of gas plumes and a localization of gas sources. We also present first results showing the gas sensing and aiming capabilities under realistic conditions. T2 - IEEE International Conference on Robotics and Automation (ICRA) CY - Singapore DA - 29.05.2017 KW - Tunable Diode Laser Absorption Spectroscopy (TDLAS) KW - 3-axis gimbal KW - Mobile Robot Olfaction KW - Tomographic reconstruction of gas plumes KW - Localization of gas sources KW - Aerial platform PY - 2017 SN - 978-1-5090-4632-4 SP - 3910 EP - 3916 PB - IEEE AN - OPUS4-40545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fittschen, U.E.A. A1 - Menzel, M. A1 - Scharf, O. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Buzanich, Günter A1 - Lopez, V.M. A1 - McIntosh, K. A1 - Streli, C. A1 - Havrilla, G.J. T1 - Observation of X-ray shadings in synchrotron radiation-total reflection X-ray fluorescence using a color X-ray camera N2 - Absorption effects and the impact of specimen shape on TXRF analysis has been discussed intensively. Model calculations indicated that ring shaped specimens should give better results in terms of higher counts per mass signals than filled rectangle or circle shaped specimens. One major reason for the difference in signal is shading effects. Full field micro-XRF with a color X-ray camera (CXC) was used to investigate shading, which occurs when working with small angles of excitation as in TXRF. The device allows monitoring the illuminated parts of the sample and the shaded parts at the same time. It is expected that sample material hit first by the primary beam shade material behind it. Using the CXC shading could be directly visualized for the high concentration specimens. In order to compare the experimental results with calculation of the shading effect the generation of controlled specimens is crucial. This was achieved by 'drop on demand' technology. It allows generating uniform, microscopic deposits of elements. The experimentally measured shadings match well with those expected from calculation. KW - TXRF KW - Full field micro-XRF KW - Color X-ray camera PY - 2014 DO - https://doi.org/10.1016/j.sab.2014.06.025 SN - 0584-8547 SN - 0038-6987 VL - 99 SP - 179 EP - 184 PB - Elsevier CY - Amsterdam AN - OPUS4-31180 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuhne, Maren A1 - Dippong, Martin A1 - Flemig, Sabine A1 - Hoffmann, Katrin A1 - Petsch, K. A1 - Schenk, J.A. A1 - Kunte, Hans-Jörg A1 - Schneider, Rudolf T1 - Comparative characterization of mAb producing hapten-specific hybridoma cells by flow cytometric analysis and ELISA N2 - A novel method that optimizes the screening for antibody-secreting hapten-specific hybridoma cells by using flow cytometry is described. Cell clones specific for five different haptens were analyzed. We selectively double stained and analyzed fixed hybridoma cells with fluorophore-labeled haptens to demonstrate the target-selectivity, and with a fluorophore-labeled anti-mouse IgG antibody to characterize the level of surface expression of membrane-bound IgGs. ELISA measurements with the supernatants of the individual hybridoma clones revealed that antibodies from those cells, which showed the highest fluorescence intensities in the flow cytometric analysis, also displayed the highest affinities for the target antigens. The fluorescence intensity of antibody-producing cells corresponded well with the produced antibodies' affinities toward their respective antigens. Immunohistochemical staining verified the successful double labeling of the cells. Our method makes it possible to perform a high-throughput screening for hybridoma cells, which have both an adequate IgG production rate and a high target affinity. KW - Immunization KW - Hapten KW - Monoclonal antibodies KW - Hybridoma KW - Flow cytometry KW - ELISA KW - Estradiol KW - Estrone KW - Digoxigenin KW - Zearalenone KW - Aflatoxin KW - CLSM PY - 2014 DO - https://doi.org/10.1016/j.jim.2014.07.004 SN - 0022-1759 SN - 1872-7905 VL - 413 SP - 45 EP - 56 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-32322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -