TY - CONF A1 - Meyer, Klas A1 - Paul, Andrea A1 - Ruiken, J.-P. A1 - Westad, Frank A1 - Illner, M. A1 - Müller, D. A1 - Esche, E. A1 - Repke, J.-U. A1 - Maiwald, Michael T1 - Online Spectroscopy in Microemulsions – A Process Analytical Approach for a Hydroformylation Mini-plant N2 - Within the Collaborative Research Center InPROMPT a novel process concept for the hydroformylation of long-chained olefins is studied in a mini-plant, using a rhodium complex as catalyst in the presence of syngas. Recently, the hydroformylation in micro¬emulsions, which allows for the efficient recycling of the expensive rhodium catalyst, was found to be feasible. However, the high sensitivity of this multi-phase system with regard to changes in temperature and composition demands a continuous observation of the reaction to achieve a reliable and economic plant operation. For that purpose, we tested the potential of both online NMR and Raman spectroscopy for process control. The lab-scale experiments were supported by off-line GC-analysis as a reference method. A fiber optic coupled probe of a process Raman spectrometer was directly integrated into the reactor. 25 mixtures with varying concentrations of olefin (1-dodecene), product (n-tridecanal), water, n-dodecane, and technical surfactant (Marlipal 24/70) were prepared according to a D-optimal design. Online NMR spectroscopy was implemented by using a flow probe equipped with 1/16” PFA tubing serving as a flow cell. This was hyphenated to the reactor within a thermostated bypass to maintain process conditions in the transfer lines. Partial least squares regression (PLSR) models were established based on the initial spectra after activation of the reaction with syngas for the prediction of unknown concentrations of 1-dodecene and n-tridecanal over the course of the reaction in the lab-scale system. The obtained Raman spectra do not only contain information on the chemical composition but are further affected by the emulsion properties of the mixtures, which depend on the phase state and the type of micelles. Based on the spectral signature of both Raman and NMR spectra, it could be deduced that especially in reaction mixtures with high 1-dodecene content the formation of isomers as a competitive reaction was dominating. Similar trends were also observed during some of the process runs in the mini-plant. The multivariate calibration allowed for the estimation of reactants and products of the hydroformylation reaction in both laboratory setup and mini-plant. T2 - 4th European Conference on Process Analytics and Control Technology (EuroPACT 2017) CY - Potsdam, Germany DA - 10.05.2017 KW - Microemulsions KW - Process Analytical Technology KW - Reaction Monitoring KW - Online NMR Spectroscopy KW - Online Raman Spectroscopy PY - 2017 SP - 64 EP - 64 CY - Frankfurt a. M. AN - OPUS4-40228 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Musolff, Andre A1 - Nakagami, M. A1 - Komatsuki, S. A1 - Tamaki, H. A1 - Kishimoto, J. A1 - Fujisawa, K. A1 - Nishio, T. ED - Quercetti, Thomas T1 - Experimental testing of RAM packages within Japanese German projects N2 - In context with Japanese disposal and transport container safety assessment the German Federal Institute for Materials Research and Testing (Bundesanstalt für Materialforschung und -prüfung) per-formed extensive drop test series with prototypes of RAM packages in recent years. The paper presents two cooperative projects focused on project management, testing performance and experimental results. In the first project, a full-scale prototype of a package for transport and storage of spent fuel elements with a total mass of 127,000 kg and its reduced-scale model which was similar to the prototype in both geometry and design were drop tested in 9 m and 1 m puncture tests at various drop orientations under regulatory conditions. In context with a corresponding research project the test data was used in combination with numerical methods to investigate the phenomenon of internal cask- content collisions during drop tests. Here, technological gaps between basket or radioactive content and cask body or primary lid can be a reason for significant high dynamic loadings of cask components and its internals due to additional impact interactions in the cask cavity caused by inner relative movement between content and cask. Further investigations were carried out in the field of similarity mechanics comparing experimental drop test data of the full-scale prototype and reduced-scale model in regard to the transferability of package impact response from reduced-scale models to full-scale packages. In the second project, drop tests with a waste container for intermediate depth disposal were per-formed being contracted by Kobe Steel, Ltd. and a consortium of Japanese electric power plant com-panies. The drop test program comprised three single 8-m drop tests in a specimen’s corner edge orientation. For drop tests according to legal regulations for interim storage or final disposal it is often necessary to use a target which represents the real ground of the storage facility. In such cases the container hits directly onto a well-defined concrete slab on top of the IAEA target. Here, the directly impact target for the drop tests were concrete slabs manufactured in Japan and connected by mortar to the impact pad of the unyielding IAEA target. KW - Drop testing KW - Package PY - 2016 SP - Paper 1043, 1 EP - 13 CY - Kobe, Japan AN - OPUS4-37557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Takahashi, Kazunori A1 - Ewert, Uwe A1 - Rosenthal, Martina A1 - Brekow, Gerhard A1 - Böhm, R. A1 - Ronneteg, U. A1 - Pitkänen, J. T1 - POD Evaluation of NDE Techniques for Canister-Components for Risk Assessment of Nuclear Waste Encapsulation T2 - 6th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurised Components CY - Budapest, Hungary DA - 2007-10-08 KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - POD PY - 2008 SN - 978-92-79-08897-1 DO - https://doi.org/10.2790/1274 SN - 1018-5593 SP - 168 EP - 179 AN - OPUS4-18589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Christina A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Heidt, Heinrich A1 - Pavlovic, Mato A1 - Rosenthal, Martina A1 - Takahashi, K. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Progress in evaluating the reliability of NDE systems - Paradigm shift N2 - The paper will give an overview of new methodology for evaluating the reliability of NDE systems accurately, reliably and efficiently in accordance with the specific requirements of industrial application. After a review of the substantive issues from the previous workshops, the go forward guidance from these interactions is considered. At the beginning of the reliability analysis, the actual safety demands have to be defined in order to fit the investigation to the level of risk when the component would fail. Next, all the essential influencing parameters need to be documented and transferred to an appropriate design of experiments (DOE) to determine the reliability in terms of a qualitative assessment for lower risk or in terms of a quantitative probability of detection (POD) or ROC (Receiver Operating Characteristics) curves for higher safety demands. A new paradigm is offered to consider the POD or reliability of the system as a function of the configuration of input variables and use it for optimisation rather than for a final judgement. An advantage for the end user is also to sample all single PODs to an integral 'Volume POD' of a part. Among the influencing parameters, the human factor is the most important one. A systematic psychological approach shall help to find out where the bottlenecks are but most importantly to provide best possible working conditions for the human inspectors. T2 - 4th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2009-06-24 KW - Zuverlässigkeit von ZfP-Systemen KW - Multiparameter POD PY - 2009 UR - http://www.ndt.net/article/reliability2009/Inhalt/we1a2.pdf SN - 978-3-940283-17-7 IS - DGZfP-BB 116 SP - 1 EP - 13 AN - OPUS4-20616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Takahashi, K. A1 - Pavlovic, Mato A1 - Ronneteg, U. A1 - Pitkänen, J. A1 - Müller, Christina T1 - Probability of detection from C-scan data for reliability analysis of ultrasonic non-destructive testing T2 - 4th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2009-06-24 KW - POD KW - UT KW - Reliability KW - C-scan PY - 2009 SN - 978-3-940283-17-7 IS - DGZfP-BB 116 SP - 1 EP - 7 AN - OPUS4-20617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pavlovic, Mato A1 - Takahashi, K. A1 - Ronneteg, U. A1 - Pitkänen, J. A1 - Müller, Christina T1 - Multi-parameter influence on the response of the flaw to the phased array ultrasonic NDT system. The volume POD. T2 - 4th European-American workshop on reliability of NDE CY - Berlin, Germany DA - 2009-06-24 KW - POD KW - Reliability KW - Multi-parameter signal response PY - 2009 SN - 978-3-940283-17-7 IS - DGZfP-BB 116 SP - 1 EP - 6 AN - OPUS4-20618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wondraczek, L. A1 - Reinsch, Stefan A1 - Gaber, Martin A1 - Deubener, J. A1 - Müller, Ralf A1 - Komatsu, T. T1 - Nano-crystalline germanate glass-ceramics T2 - 78. Glastechnische Tagung CY - Nürnberg, Deutschland DA - 2004-06-07 PY - 2004 SP - 37 EP - 40 PB - Deutsche Glastechnische Gesellschaft CY - Offenbach AN - OPUS4-6953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlaad, H. A1 - Müller, A. A1 - Spickermann, J. A1 - Räder, H. A1 - Krüger, Ralph-Peter T1 - Quantitative Analysis of Molecular Weight Distribution Obtained by Matrix-Assisted Laser Desorption/Ionization Time-of-Flight Mass Spectrometry (MALDI-TOF-MS) T2 - 2nd International Conference on Molecular Mass Characterization of Synthetic and Natural Polymers CY - Bradford, England, UK DA - 1996-04-01 PY - 1996 CY - Bradford AN - OPUS4-2218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, J. A1 - Kiechle, H. A1 - Ewert, Uwe A1 - Rädel, Christoph A1 - Redmer, Bernhard T1 - Mobile Computer Tomography for In-Service Inspection in Nuclear Power Plants T2 - 9th European Conference on NDT CY - Berlin, Germany DA - 2006-09-25 KW - Röntgen KW - Digitale Detektoren KW - Tomographie KW - TomoCAR KW - Schweißnähte KW - Analyse KW - Bewertung PY - 2006 SN - 3-931381-86-2 SP - 1(?) EP - 6(?) PB - European Federation for Non-Destructive Testing CY - Berlin AN - OPUS4-14376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato A1 - Boehm, Rainer A1 - Müller, Christina A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Investigation of the influence of the material attenuation on the POD of the flaws T2 - 8th International conference on NDE in relation to structural integrity for nuclear and pressurised components CY - Berlin, Germany DA - 2010-09-29 KW - POD KW - NDT KW - Attenuation KW - Ultrasonic KW - Reliability PY - 2010 SN - 978-3-940283-30-6 IS - DGZfP-BB 125 (Th.2.B.2) SP - 1 EP - 9 CY - Berlin AN - OPUS4-23922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -